* [PATCH 0/2] ARM: at91: allow all boards to use atmel-mci driver @ 2012-05-16 15:51 ` ludovic.desroches at atmel.com 0 siblings, 0 replies; 28+ messages in thread From: ludovic.desroches @ 2012-05-16 15:51 UTC (permalink / raw) To: linux-mmc, linux-arm-kernel; +Cc: nicolas.ferre, plagnioj This set of patches depends on 'mmc: atmel-mci: add support for old mci IPs' which allows to use atmel-mci driver on all boards. So keeping at91-mci only for old chips is no more necessary. If there are no issues with this new atmel-mci driver, at91-mci driver will be removed for 3.7 release. Regards Ludovic ^ permalink raw reply [flat|nested] 28+ messages in thread
* [PATCH 0/2] ARM: at91: allow all boards to use atmel-mci driver @ 2012-05-16 15:51 ` ludovic.desroches at atmel.com 0 siblings, 0 replies; 28+ messages in thread From: ludovic.desroches at atmel.com @ 2012-05-16 15:51 UTC (permalink / raw) To: linux-arm-kernel This set of patches depends on 'mmc: atmel-mci: add support for old mci IPs' which allows to use atmel-mci driver on all boards. So keeping at91-mci only for old chips is no more necessary. If there are no issues with this new atmel-mci driver, at91-mci driver will be removed for 3.7 release. Regards Ludovic ^ permalink raw reply [flat|nested] 28+ messages in thread
* [PATCH 1/2] ARM: at91: add atmel-mci support for chips and boards which can use it 2012-05-16 15:51 ` ludovic.desroches at atmel.com @ 2012-05-16 15:51 ` ludovic.desroches at atmel.com -1 siblings, 0 replies; 28+ messages in thread From: ludovic.desroches @ 2012-05-16 15:51 UTC (permalink / raw) To: linux-mmc, linux-arm-kernel; +Cc: nicolas.ferre, plagnioj, Ludovic Desroches From: Ludovic Desroches <ludovic.desroches@atmel.com> Since atmel-mci driver supports all atmel mci version excepted the rm9200 one, use it instead of at91_mci driver. Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> --- arch/arm/mach-at91/at91rm9200_devices.c | 99 ++++++++++++++++++ arch/arm/mach-at91/at91sam9261_devices.c | 67 ++++++++++++ arch/arm/mach-at91/at91sam9263.c | 2 + arch/arm/mach-at91/at91sam9263_devices.c | 164 ++++++++++++++++++++++++++++++ arch/arm/mach-at91/at91sam9rl_devices.c | 70 +++++++++++++ arch/arm/mach-at91/board-foxg20.c | 16 +++- arch/arm/mach-at91/board-rm9200ek.c | 14 +++ arch/arm/mach-at91/board-sam9-l9260.c | 16 +++- arch/arm/mach-at91/board-sam9260ek.c | 16 +++- arch/arm/mach-at91/board-sam9261ek.c | 14 +++ arch/arm/mach-at91/board-sam9263ek.c | 14 +++ arch/arm/mach-at91/board-sam9rlek.c | 14 +++ arch/arm/mach-at91/board-usb-a926x.c | 2 +- 13 files changed, 504 insertions(+), 4 deletions(-) diff --git a/arch/arm/mach-at91/at91rm9200_devices.c b/arch/arm/mach-at91/at91rm9200_devices.c index 05774e5..2c13783 100644 --- a/arch/arm/mach-at91/at91rm9200_devices.c +++ b/arch/arm/mach-at91/at91rm9200_devices.c @@ -374,6 +374,105 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {} /* -------------------------------------------------------------------- + * MMC / SD + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static u64 mmc_dmamask = DMA_BIT_MASK(32); +static struct mci_platform_data mmc_data; + +static struct resource mmc_resources[] = { + [0] = { + .start = AT91RM9200_BASE_MCI, + .end = AT91RM9200_BASE_MCI + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91RM9200_ID_MCI, + .end = AT91RM9200_ID_MCI, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91rm9200_mmc_device = { + .name = "atmel_mci", + .id = -1, + .dev = { + .dma_mask = &mmc_dmamask, + .coherent_dma_mask = DMA_BIT_MASK(32), + .platform_data = &mmc_data, + }, + .resource = mmc_resources, + .num_resources = ARRAY_SIZE(mmc_resources), +}; + +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) +{ + unsigned int i; + unsigned int slot_count = 0; + + if (!data) + return; + + for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) { + + if (!data->slot[i].bus_width) + continue; + + /* input/irq */ + if (gpio_is_valid(data->slot[i].detect_pin)) { + at91_set_gpio_input(data->slot[i].detect_pin, 1); + at91_set_deglitch(data->slot[i].detect_pin, 1); + } + if (gpio_is_valid(data->slot[i].wp_pin)) + at91_set_gpio_input(data->slot[i].wp_pin, 1); + + switch (i) { + case 0: /* slot A */ + /* CMD */ + at91_set_A_periph(AT91_PIN_PA28, 1); + /* DAT0, maybe DAT1..DAT3 */ + at91_set_A_periph(AT91_PIN_PA29, 1); + if (data->slot[i].bus_width == 4) { + at91_set_B_periph(AT91_PIN_PB3, 1); + at91_set_B_periph(AT91_PIN_PB4, 1); + at91_set_B_periph(AT91_PIN_PB5, 1); + } + slot_count++; + break; + case 1: /* slot B */ + /* CMD */ + at91_set_B_periph(AT91_PIN_PA8, 1); + /* DAT0, maybe DAT1..DAT3 */ + at91_set_B_periph(AT91_PIN_PA9, 1); + if (data->slot[i].bus_width == 4) { + at91_set_B_periph(AT91_PIN_PA10, 1); + at91_set_B_periph(AT91_PIN_PA11, 1); + at91_set_B_periph(AT91_PIN_PA12, 1); + } + slot_count++; + break; + default: + printk(KERN_ERR + "AT91: SD/MMC slot %d not available\n", i); + break; + } + if (slot_count) { + /* CLK */ + at91_set_A_periph(AT91_PIN_PA27, 0); + + mmc_data = *data; + platform_device_register(&at91rm9200_mmc_device); + } + } + +} +#else +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {} +#endif + + +/* -------------------------------------------------------------------- * NAND / SmartMedia * -------------------------------------------------------------------- */ diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c index 4db961a..0817854 100644 --- a/arch/arm/mach-at91/at91sam9261_devices.c +++ b/arch/arm/mach-at91/at91sam9261_devices.c @@ -202,7 +202,74 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {} #endif +/* -------------------------------------------------------------------- + * MMC / SD Slot for Atmel MCI Driver + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static u64 mmc_dmamask = DMA_BIT_MASK(32); +static struct mci_platform_data mmc_data; + +static struct resource mmc_resources[] = { + [0] = { + .start = AT91SAM9261_BASE_MCI, + .end = AT91SAM9261_BASE_MCI + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9261_ID_MCI, + .end = AT91SAM9261_ID_MCI, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91sam9261_mmc_device = { + .name = "atmel_mci", + .id = -1, + .dev = { + .dma_mask = &mmc_dmamask, + .coherent_dma_mask = DMA_BIT_MASK(32), + .platform_data = &mmc_data, + }, + .resource = mmc_resources, + .num_resources = ARRAY_SIZE(mmc_resources), +}; + +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) +{ + if (!data) + return; + if (data->slot[0].bus_width) { + /* input/irq */ + if (gpio_is_valid(data->slot[0].detect_pin)) { + at91_set_gpio_input(data->slot[0].detect_pin, 1); + at91_set_deglitch(data->slot[0].detect_pin, 1); + } + if (gpio_is_valid(data->slot[0].wp_pin)) + at91_set_gpio_input(data->slot[0].wp_pin, 1); + + /* CLK */ + at91_set_B_periph(AT91_PIN_PA2, 0); + + /* CMD */ + at91_set_B_periph(AT91_PIN_PA1, 1); + + /* DAT0, maybe DAT1..DAT3 */ + at91_set_B_periph(AT91_PIN_PA0, 1); + if (data->slot[0].bus_width == 4) { + at91_set_B_periph(AT91_PIN_PA4, 1); + at91_set_B_periph(AT91_PIN_PA5, 1); + at91_set_B_periph(AT91_PIN_PA6, 1); + } + + mmc_data = *data; + platform_device_register(&at91sam9261_mmc_device); + } +} +#else +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {} +#endif /* -------------------------------------------------------------------- * NAND / SmartMedia * -------------------------------------------------------------------- */ diff --git a/arch/arm/mach-at91/at91sam9263.c b/arch/arm/mach-at91/at91sam9263.c index ef301be..053e47a 100644 --- a/arch/arm/mach-at91/at91sam9263.c +++ b/arch/arm/mach-at91/at91sam9263.c @@ -189,6 +189,8 @@ static struct clk_lookup periph_clocks_lookups[] = { CLKDEV_CON_DEV_ID("pclk", "ssc.1", &ssc1_clk), CLKDEV_CON_DEV_ID("mci_clk", "at91_mci.0", &mmc0_clk), CLKDEV_CON_DEV_ID("mci_clk", "at91_mci.1", &mmc1_clk), + CLKDEV_CON_DEV_ID("mci_clk", "atmel_mci.0", &mmc0_clk), + CLKDEV_CON_DEV_ID("mci_clk", "atmel_mci.1", &mmc1_clk), CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.0", &spi0_clk), CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.1", &spi1_clk), CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tcb_clk), diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c index fe99206..617fbfc 100644 --- a/arch/arm/mach-at91/at91sam9263_devices.c +++ b/arch/arm/mach-at91/at91sam9263_devices.c @@ -354,6 +354,170 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {} #endif /* -------------------------------------------------------------------- + * MMC / SD + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static u64 mmc_dmamask = DMA_BIT_MASK(32); +static struct mci_platform_data mmc0_data, mmc1_data; + +static struct resource mmc0_resources[] = { + [0] = { + .start = AT91SAM9263_BASE_MCI0, + .end = AT91SAM9263_BASE_MCI0 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9263_ID_MCI0, + .end = AT91SAM9263_ID_MCI0, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91sam9263_mmc0_device = { + .name = "atmel_mci", + .id = 0, + .dev = { + .dma_mask = &mmc_dmamask, + .coherent_dma_mask = DMA_BIT_MASK(32), + .platform_data = &mmc0_data, + }, + .resource = mmc0_resources, + .num_resources = ARRAY_SIZE(mmc0_resources), +}; + +static struct resource mmc1_resources[] = { + [0] = { + .start = AT91SAM9263_BASE_MCI1, + .end = AT91SAM9263_BASE_MCI1 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9263_ID_MCI1, + .end = AT91SAM9263_ID_MCI1, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91sam9263_mmc1_device = { + .name = "atmel_mci", + .id = 1, + .dev = { + .dma_mask = &mmc_dmamask, + .coherent_dma_mask = DMA_BIT_MASK(32), + .platform_data = &mmc1_data, + }, + .resource = mmc1_resources, + .num_resources = ARRAY_SIZE(mmc1_resources), +}; + +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) +{ + unsigned int i; + unsigned int slot_count = 0; + + if (!data) + return; + + for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) { + + if (!data->slot[i].bus_width) + continue; + + /* input/irq */ + if (gpio_is_valid(data->slot[i].detect_pin)) { + at91_set_gpio_input(data->slot[i].detect_pin, + 1); + at91_set_deglitch(data->slot[i].detect_pin, + 1); + } + if (gpio_is_valid(data->slot[i].wp_pin)) + at91_set_gpio_input(data->slot[i].wp_pin, 1); + + if (mmc_id == 0) { /* MCI0 */ + switch (i) { + case 0: /* slot A */ + /* CMD */ + at91_set_A_periph(AT91_PIN_PA1, 1); + /* DAT0, maybe DAT1..DAT3 */ + at91_set_A_periph(AT91_PIN_PA0, 1); + if (data->slot[i].bus_width == 4) { + at91_set_A_periph(AT91_PIN_PA3, 1); + at91_set_A_periph(AT91_PIN_PA4, 1); + at91_set_A_periph(AT91_PIN_PA5, 1); + } + slot_count++; + break; + case 1: /* slot B */ + /* CMD */ + at91_set_A_periph(AT91_PIN_PA16, 1); + /* DAT0, maybe DAT1..DAT3 */ + at91_set_A_periph(AT91_PIN_PA17, 1); + if (data->slot[i].bus_width == 4) { + at91_set_A_periph(AT91_PIN_PA18, 1); + at91_set_A_periph(AT91_PIN_PA19, 1); + at91_set_A_periph(AT91_PIN_PA20, 1); + } + slot_count++; + break; + default: + printk(KERN_ERR + "AT91: SD/MMC slot %d not available\n", i); + break; + } + if (slot_count) { + /* CLK */ + at91_set_A_periph(AT91_PIN_PA12, 0); + + mmc0_data = *data; + platform_device_register(&at91sam9263_mmc0_device); + } + } else if (mmc_id == 1) { /* MCI1 */ + switch (i) { + case 0: /* slot A */ + /* CMD */ + at91_set_A_periph(AT91_PIN_PA7, 1); + /* DAT0, maybe DAT1..DAT3 */ + at91_set_A_periph(AT91_PIN_PA8, 1); + if (data->slot[i].bus_width == 4) { + at91_set_A_periph(AT91_PIN_PA9, 1); + at91_set_A_periph(AT91_PIN_PA10, 1); + at91_set_A_periph(AT91_PIN_PA11, 1); + } + slot_count++; + break; + case 1: /* slot B */ + /* CMD */ + at91_set_A_periph(AT91_PIN_PA21, 1); + /* DAT0, maybe DAT1..DAT3 */ + at91_set_A_periph(AT91_PIN_PA22, 1); + if (data->slot[i].bus_width == 4) { + at91_set_A_periph(AT91_PIN_PA23, 1); + at91_set_A_periph(AT91_PIN_PA24, 1); + at91_set_A_periph(AT91_PIN_PA25, 1); + } + slot_count++; + break; + default: + printk(KERN_ERR + "AT91: SD/MMC slot %d not available\n", i); + break; + } + if (slot_count) { + /* CLK */ + at91_set_A_periph(AT91_PIN_PA6, 0); + + mmc1_data = *data; + platform_device_register(&at91sam9263_mmc1_device); + } + } + } +} +#else +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {} +#endif + +/* -------------------------------------------------------------------- * Compact Flash (PCMCIA or IDE) * -------------------------------------------------------------------- */ diff --git a/arch/arm/mach-at91/at91sam9rl_devices.c b/arch/arm/mach-at91/at91sam9rl_devices.c index fe4ae22..83c5845 100644 --- a/arch/arm/mach-at91/at91sam9rl_devices.c +++ b/arch/arm/mach-at91/at91sam9rl_devices.c @@ -228,6 +228,76 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {} /* -------------------------------------------------------------------- + * MMC / SD + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static u64 mmc_dmamask = DMA_BIT_MASK(32); +static struct mci_platform_data mmc_data; + +static struct resource mmc_resources[] = { + [0] = { + .start = AT91SAM9RL_BASE_MCI, + .end = AT91SAM9RL_BASE_MCI + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9RL_ID_MCI, + .end = AT91SAM9RL_ID_MCI, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91sam9rl_mmc_device = { + .name = "atmel_mci", + .id = -1, + .dev = { + .dma_mask = &mmc_dmamask, + .coherent_dma_mask = DMA_BIT_MASK(32), + .platform_data = &mmc_data, + }, + .resource = mmc_resources, + .num_resources = ARRAY_SIZE(mmc_resources), +}; + +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) +{ + if (!data) + return; + + if (data->slot[0].bus_width) { + /* input/irq */ + if (gpio_is_valid(data->slot[0].detect_pin)) { + at91_set_gpio_input(data->slot[0].detect_pin, 1); + at91_set_deglitch(data->slot[0].detect_pin, 1); + } + if (gpio_is_valid(data->slot[0].wp_pin)) + at91_set_gpio_input(data->slot[0].wp_pin, 1); + + /* CLK */ + at91_set_A_periph(AT91_PIN_PA2, 0); + + /* CMD */ + at91_set_A_periph(AT91_PIN_PA1, 1); + + /* DAT0, maybe DAT1..DAT3 */ + at91_set_A_periph(AT91_PIN_PA0, 1); + if (data->slot[0].bus_width == 4) { + at91_set_A_periph(AT91_PIN_PA3, 1); + at91_set_A_periph(AT91_PIN_PA4, 1); + at91_set_A_periph(AT91_PIN_PA5, 1); + } + + mmc_data = *data; + platform_device_register(&at91sam9rl_mmc_device); + } +} +#else +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {} +#endif + + +/* -------------------------------------------------------------------- * NAND / SmartMedia * -------------------------------------------------------------------- */ diff --git a/arch/arm/mach-at91/board-foxg20.c b/arch/arm/mach-at91/board-foxg20.c index caf017f..6cda303 100644 --- a/arch/arm/mach-at91/board-foxg20.c +++ b/arch/arm/mach-at91/board-foxg20.c @@ -123,7 +123,7 @@ static struct at91_udc_data __initdata foxg20_udc_data = { * SPI devices. */ static struct spi_board_info foxg20_spi_devices[] = { -#if !defined(CONFIG_MMC_AT91) +#if !defined(CONFIG_MMC_AT91) && !defined(CONFIG_MMC_ATMELMCI) { .modalias = "mtd_dataflash", .chip_select = 1, @@ -146,6 +146,7 @@ static struct macb_platform_data __initdata foxg20_macb_data = { * MCI (SD/MMC) * det_pin, wp_pin and vcc_pin are not connected */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) static struct at91_mmc_data __initdata foxg20_mmc_data = { .slot_b = 1, .wire4 = 1, @@ -153,6 +154,15 @@ static struct at91_mmc_data __initdata foxg20_mmc_data = { .wp_pin = -EINVAL, .vcc_pin = -EINVAL, }; +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata foxg20_mci0_data = { + .slot[1] = { + .bus_width = 4, + .detect_pin = -EINVAL, + .wp_pin = -EINVAL, + }, +}; +#endif /* @@ -251,7 +261,11 @@ static void __init foxg20_board_init(void) /* Ethernet */ at91_add_device_eth(&foxg20_macb_data); /* MMC */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) at91_add_device_mmc(0, &foxg20_mmc_data); +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &foxg20_mci0_data); +#endif /* I2C */ at91_add_device_i2c(foxg20_i2c_devices, ARRAY_SIZE(foxg20_i2c_devices)); /* LEDs */ diff --git a/arch/arm/mach-at91/board-rm9200ek.c b/arch/arm/mach-at91/board-rm9200ek.c index b2e4fe2..7177aac 100644 --- a/arch/arm/mach-at91/board-rm9200ek.c +++ b/arch/arm/mach-at91/board-rm9200ek.c @@ -83,6 +83,7 @@ static struct at91_udc_data __initdata ek_udc_data = { }; #ifndef CONFIG_MTD_AT91_DATAFLASH_CARD +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) static struct at91_mmc_data __initdata ek_mmc_data = { .det_pin = AT91_PIN_PB27, .slot_b = 0, @@ -90,6 +91,15 @@ static struct at91_mmc_data __initdata ek_mmc_data = { .wp_pin = AT91_PIN_PA17, .vcc_pin = -EINVAL, }; +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata ek_mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PB27, + .wp_pin = AT91_PIN_PA17, + } +}; +#endif #endif static struct spi_board_info ek_spi_devices[] = { @@ -180,7 +190,11 @@ static void __init ek_board_init(void) #else /* MMC */ at91_set_gpio_output(AT91_PIN_PB22, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) at91_add_device_mmc(0, &ek_mmc_data); +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &ek_mci0_data); +#endif #endif /* NOR Flash */ platform_device_register(&ek_flash); diff --git a/arch/arm/mach-at91/board-sam9-l9260.c b/arch/arm/mach-at91/board-sam9-l9260.c index e8b116b..4a5786b 100644 --- a/arch/arm/mach-at91/board-sam9-l9260.c +++ b/arch/arm/mach-at91/board-sam9-l9260.c @@ -89,7 +89,7 @@ static struct at91_udc_data __initdata ek_udc_data = { * SPI devices. */ static struct spi_board_info ek_spi_devices[] = { -#if !defined(CONFIG_MMC_AT91) +#if !defined(CONFIG_MMC_AT91) && !defined(CONFIG_MMC_ATMELMCI) { /* DataFlash chip */ .modalias = "mtd_dataflash", .chip_select = 1, @@ -174,6 +174,7 @@ static void __init ek_add_device_nand(void) /* * MCI (SD/MMC) */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) static struct at91_mmc_data __initdata ek_mmc_data = { .slot_b = 1, .wire4 = 1, @@ -181,6 +182,15 @@ static struct at91_mmc_data __initdata ek_mmc_data = { .wp_pin = AT91_PIN_PC4, .vcc_pin = -EINVAL, }; +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata mci0_data = { + .slot[1] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PC8, + .wp_pin = AT91_PIN_PC4, + }, +}; +#endif static void __init ek_board_init(void) { @@ -197,7 +207,11 @@ static void __init ek_board_init(void) /* Ethernet */ at91_add_device_eth(&ek_macb_data); /* MMC */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) at91_add_device_mmc(0, &ek_mmc_data); +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &ek_mci0_data); +#endif /* I2C */ at91_add_device_i2c(NULL, 0); } diff --git a/arch/arm/mach-at91/board-sam9260ek.c b/arch/arm/mach-at91/board-sam9260ek.c index d5aec55..b6ce2df 100644 --- a/arch/arm/mach-at91/board-sam9260ek.c +++ b/arch/arm/mach-at91/board-sam9260ek.c @@ -121,7 +121,7 @@ static void __init at73c213_set_clk(struct at73c213_board_info *info) {} * SPI devices. */ static struct spi_board_info ek_spi_devices[] = { -#if !defined(CONFIG_MMC_AT91) +#if !defined(CONFIG_MMC_AT91) && !defined(CONFIG_MMC_ATMELMCI) { /* DataFlash chip */ .modalias = "mtd_dataflash", .chip_select = 1, @@ -224,6 +224,7 @@ static void __init ek_add_device_nand(void) /* * MCI (SD/MMC) */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) static struct at91_mmc_data __initdata ek_mmc_data = { .slot_b = 1, .wire4 = 1, @@ -231,6 +232,15 @@ static struct at91_mmc_data __initdata ek_mmc_data = { .wp_pin = -EINVAL, .vcc_pin = -EINVAL, }; +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata mci0_data = { + .slot[1] = { + .bus_width = 4, + .detect_pin = -EINVAL, + .wp_pin = -EINVAL, + }, +}; +#endif /* @@ -332,7 +342,11 @@ static void __init ek_board_init(void) /* Ethernet */ at91_add_device_eth(&ek_macb_data); /* MMC */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) at91_add_device_mmc(0, &ek_mmc_data); +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &ek_mci0_data); +#endif /* I2C */ at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices)); /* SSC (to AT73C213) */ diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c index 065fed3..797dd7c 100644 --- a/arch/arm/mach-at91/board-sam9261ek.c +++ b/arch/arm/mach-at91/board-sam9261ek.c @@ -344,6 +344,7 @@ static struct spi_board_info ek_spi_devices[] = { #else /* CONFIG_SPI_ATMEL_* */ /* spi0 and mmc/sd share the same PIO pins: cannot be used at the same time */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) /* * MCI (SD/MMC) * det_pin, wp_pin and vcc_pin are not connected @@ -354,6 +355,15 @@ static struct at91_mmc_data __initdata ek_mmc_data = { .wp_pin = -EINVAL, .vcc_pin = -EINVAL, }; +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = -EINVAL, + .wp_pin = -EINVAL, + }, +}; +#endif #endif /* CONFIG_SPI_ATMEL_* */ @@ -601,7 +611,11 @@ static void __init ek_board_init(void) at91_add_device_ssc(AT91SAM9261_ID_SSC1, ATMEL_SSC_TX); #else /* MMC */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) at91_add_device_mmc(0, &ek_mmc_data); +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &mci0_data); +#endif #endif /* LCD Controller */ at91_add_device_lcdc(&ek_lcdc_data); diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c index 2ffe50f..8080d02 100644 --- a/arch/arm/mach-at91/board-sam9263ek.c +++ b/arch/arm/mach-at91/board-sam9263ek.c @@ -149,12 +149,22 @@ static struct spi_board_info ek_spi_devices[] = { /* * MCI (SD/MMC) */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) static struct at91_mmc_data __initdata ek_mmc_data = { .wire4 = 1, .det_pin = AT91_PIN_PE18, .wp_pin = AT91_PIN_PE19, .vcc_pin = -EINVAL, }; +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata mci1_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PE18, + .wp_pin = AT91_PIN_PE19, + }, +}; +#endif /* @@ -423,7 +433,11 @@ static void __init ek_board_init(void) /* Touchscreen */ ek_add_device_ts(); /* MMC */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) at91_add_device_mmc(1, &ek_mmc_data); +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(1, &mci1_data); +#endif /* Ethernet */ at91_add_device_eth(&ek_macb_data); /* NAND */ diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c index b109ce2..bb06521 100644 --- a/arch/arm/mach-at91/board-sam9rlek.c +++ b/arch/arm/mach-at91/board-sam9rlek.c @@ -64,12 +64,22 @@ static struct usba_platform_data __initdata ek_usba_udc_data = { /* * MCI (SD/MMC) */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) static struct at91_mmc_data __initdata ek_mmc_data = { .wire4 = 1, .det_pin = AT91_PIN_PA15, .wp_pin = -EINVAL, .vcc_pin = -EINVAL, }; +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PA15, + .wp_pin = -EINVAL, + }, +}; +#endif /* @@ -306,7 +316,11 @@ static void __init ek_board_init(void) /* SPI */ at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); /* MMC */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) at91_add_device_mmc(0, &ek_mmc_data); +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &mci0_data); +#endif /* LCD Controller */ at91_add_device_lcdc(&ek_lcdc_data); /* AC97 */ diff --git a/arch/arm/mach-at91/board-usb-a926x.c b/arch/arm/mach-at91/board-usb-a926x.c index b7483a3..879e34e 100644 --- a/arch/arm/mach-at91/board-usb-a926x.c +++ b/arch/arm/mach-at91/board-usb-a926x.c @@ -114,7 +114,7 @@ static struct mmc_spi_platform_data at91_mmc_spi_pdata = { * SPI devices. */ static struct spi_board_info usb_a9263_spi_devices[] = { -#if !defined(CONFIG_MMC_AT91) +#if !defined(CONFIG_MMC_AT91) && !defined(CONFIG_MMC_ATMELMCI) { /* DataFlash chip */ .modalias = "mtd_dataflash", .chip_select = 0, -- 1.7.5.4 ^ permalink raw reply related [flat|nested] 28+ messages in thread
* [PATCH 1/2] ARM: at91: add atmel-mci support for chips and boards which can use it @ 2012-05-16 15:51 ` ludovic.desroches at atmel.com 0 siblings, 0 replies; 28+ messages in thread From: ludovic.desroches at atmel.com @ 2012-05-16 15:51 UTC (permalink / raw) To: linux-arm-kernel From: Ludovic Desroches <ludovic.desroches@atmel.com> Since atmel-mci driver supports all atmel mci version excepted the rm9200 one, use it instead of at91_mci driver. Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> --- arch/arm/mach-at91/at91rm9200_devices.c | 99 ++++++++++++++++++ arch/arm/mach-at91/at91sam9261_devices.c | 67 ++++++++++++ arch/arm/mach-at91/at91sam9263.c | 2 + arch/arm/mach-at91/at91sam9263_devices.c | 164 ++++++++++++++++++++++++++++++ arch/arm/mach-at91/at91sam9rl_devices.c | 70 +++++++++++++ arch/arm/mach-at91/board-foxg20.c | 16 +++- arch/arm/mach-at91/board-rm9200ek.c | 14 +++ arch/arm/mach-at91/board-sam9-l9260.c | 16 +++- arch/arm/mach-at91/board-sam9260ek.c | 16 +++- arch/arm/mach-at91/board-sam9261ek.c | 14 +++ arch/arm/mach-at91/board-sam9263ek.c | 14 +++ arch/arm/mach-at91/board-sam9rlek.c | 14 +++ arch/arm/mach-at91/board-usb-a926x.c | 2 +- 13 files changed, 504 insertions(+), 4 deletions(-) diff --git a/arch/arm/mach-at91/at91rm9200_devices.c b/arch/arm/mach-at91/at91rm9200_devices.c index 05774e5..2c13783 100644 --- a/arch/arm/mach-at91/at91rm9200_devices.c +++ b/arch/arm/mach-at91/at91rm9200_devices.c @@ -374,6 +374,105 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {} /* -------------------------------------------------------------------- + * MMC / SD + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static u64 mmc_dmamask = DMA_BIT_MASK(32); +static struct mci_platform_data mmc_data; + +static struct resource mmc_resources[] = { + [0] = { + .start = AT91RM9200_BASE_MCI, + .end = AT91RM9200_BASE_MCI + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91RM9200_ID_MCI, + .end = AT91RM9200_ID_MCI, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91rm9200_mmc_device = { + .name = "atmel_mci", + .id = -1, + .dev = { + .dma_mask = &mmc_dmamask, + .coherent_dma_mask = DMA_BIT_MASK(32), + .platform_data = &mmc_data, + }, + .resource = mmc_resources, + .num_resources = ARRAY_SIZE(mmc_resources), +}; + +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) +{ + unsigned int i; + unsigned int slot_count = 0; + + if (!data) + return; + + for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) { + + if (!data->slot[i].bus_width) + continue; + + /* input/irq */ + if (gpio_is_valid(data->slot[i].detect_pin)) { + at91_set_gpio_input(data->slot[i].detect_pin, 1); + at91_set_deglitch(data->slot[i].detect_pin, 1); + } + if (gpio_is_valid(data->slot[i].wp_pin)) + at91_set_gpio_input(data->slot[i].wp_pin, 1); + + switch (i) { + case 0: /* slot A */ + /* CMD */ + at91_set_A_periph(AT91_PIN_PA28, 1); + /* DAT0, maybe DAT1..DAT3 */ + at91_set_A_periph(AT91_PIN_PA29, 1); + if (data->slot[i].bus_width == 4) { + at91_set_B_periph(AT91_PIN_PB3, 1); + at91_set_B_periph(AT91_PIN_PB4, 1); + at91_set_B_periph(AT91_PIN_PB5, 1); + } + slot_count++; + break; + case 1: /* slot B */ + /* CMD */ + at91_set_B_periph(AT91_PIN_PA8, 1); + /* DAT0, maybe DAT1..DAT3 */ + at91_set_B_periph(AT91_PIN_PA9, 1); + if (data->slot[i].bus_width == 4) { + at91_set_B_periph(AT91_PIN_PA10, 1); + at91_set_B_periph(AT91_PIN_PA11, 1); + at91_set_B_periph(AT91_PIN_PA12, 1); + } + slot_count++; + break; + default: + printk(KERN_ERR + "AT91: SD/MMC slot %d not available\n", i); + break; + } + if (slot_count) { + /* CLK */ + at91_set_A_periph(AT91_PIN_PA27, 0); + + mmc_data = *data; + platform_device_register(&at91rm9200_mmc_device); + } + } + +} +#else +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {} +#endif + + +/* -------------------------------------------------------------------- * NAND / SmartMedia * -------------------------------------------------------------------- */ diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c index 4db961a..0817854 100644 --- a/arch/arm/mach-at91/at91sam9261_devices.c +++ b/arch/arm/mach-at91/at91sam9261_devices.c @@ -202,7 +202,74 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {} #endif +/* -------------------------------------------------------------------- + * MMC / SD Slot for Atmel MCI Driver + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static u64 mmc_dmamask = DMA_BIT_MASK(32); +static struct mci_platform_data mmc_data; + +static struct resource mmc_resources[] = { + [0] = { + .start = AT91SAM9261_BASE_MCI, + .end = AT91SAM9261_BASE_MCI + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9261_ID_MCI, + .end = AT91SAM9261_ID_MCI, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91sam9261_mmc_device = { + .name = "atmel_mci", + .id = -1, + .dev = { + .dma_mask = &mmc_dmamask, + .coherent_dma_mask = DMA_BIT_MASK(32), + .platform_data = &mmc_data, + }, + .resource = mmc_resources, + .num_resources = ARRAY_SIZE(mmc_resources), +}; + +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) +{ + if (!data) + return; + if (data->slot[0].bus_width) { + /* input/irq */ + if (gpio_is_valid(data->slot[0].detect_pin)) { + at91_set_gpio_input(data->slot[0].detect_pin, 1); + at91_set_deglitch(data->slot[0].detect_pin, 1); + } + if (gpio_is_valid(data->slot[0].wp_pin)) + at91_set_gpio_input(data->slot[0].wp_pin, 1); + + /* CLK */ + at91_set_B_periph(AT91_PIN_PA2, 0); + + /* CMD */ + at91_set_B_periph(AT91_PIN_PA1, 1); + + /* DAT0, maybe DAT1..DAT3 */ + at91_set_B_periph(AT91_PIN_PA0, 1); + if (data->slot[0].bus_width == 4) { + at91_set_B_periph(AT91_PIN_PA4, 1); + at91_set_B_periph(AT91_PIN_PA5, 1); + at91_set_B_periph(AT91_PIN_PA6, 1); + } + + mmc_data = *data; + platform_device_register(&at91sam9261_mmc_device); + } +} +#else +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {} +#endif /* -------------------------------------------------------------------- * NAND / SmartMedia * -------------------------------------------------------------------- */ diff --git a/arch/arm/mach-at91/at91sam9263.c b/arch/arm/mach-at91/at91sam9263.c index ef301be..053e47a 100644 --- a/arch/arm/mach-at91/at91sam9263.c +++ b/arch/arm/mach-at91/at91sam9263.c @@ -189,6 +189,8 @@ static struct clk_lookup periph_clocks_lookups[] = { CLKDEV_CON_DEV_ID("pclk", "ssc.1", &ssc1_clk), CLKDEV_CON_DEV_ID("mci_clk", "at91_mci.0", &mmc0_clk), CLKDEV_CON_DEV_ID("mci_clk", "at91_mci.1", &mmc1_clk), + CLKDEV_CON_DEV_ID("mci_clk", "atmel_mci.0", &mmc0_clk), + CLKDEV_CON_DEV_ID("mci_clk", "atmel_mci.1", &mmc1_clk), CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.0", &spi0_clk), CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.1", &spi1_clk), CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tcb_clk), diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c index fe99206..617fbfc 100644 --- a/arch/arm/mach-at91/at91sam9263_devices.c +++ b/arch/arm/mach-at91/at91sam9263_devices.c @@ -354,6 +354,170 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {} #endif /* -------------------------------------------------------------------- + * MMC / SD + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static u64 mmc_dmamask = DMA_BIT_MASK(32); +static struct mci_platform_data mmc0_data, mmc1_data; + +static struct resource mmc0_resources[] = { + [0] = { + .start = AT91SAM9263_BASE_MCI0, + .end = AT91SAM9263_BASE_MCI0 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9263_ID_MCI0, + .end = AT91SAM9263_ID_MCI0, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91sam9263_mmc0_device = { + .name = "atmel_mci", + .id = 0, + .dev = { + .dma_mask = &mmc_dmamask, + .coherent_dma_mask = DMA_BIT_MASK(32), + .platform_data = &mmc0_data, + }, + .resource = mmc0_resources, + .num_resources = ARRAY_SIZE(mmc0_resources), +}; + +static struct resource mmc1_resources[] = { + [0] = { + .start = AT91SAM9263_BASE_MCI1, + .end = AT91SAM9263_BASE_MCI1 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9263_ID_MCI1, + .end = AT91SAM9263_ID_MCI1, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91sam9263_mmc1_device = { + .name = "atmel_mci", + .id = 1, + .dev = { + .dma_mask = &mmc_dmamask, + .coherent_dma_mask = DMA_BIT_MASK(32), + .platform_data = &mmc1_data, + }, + .resource = mmc1_resources, + .num_resources = ARRAY_SIZE(mmc1_resources), +}; + +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) +{ + unsigned int i; + unsigned int slot_count = 0; + + if (!data) + return; + + for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) { + + if (!data->slot[i].bus_width) + continue; + + /* input/irq */ + if (gpio_is_valid(data->slot[i].detect_pin)) { + at91_set_gpio_input(data->slot[i].detect_pin, + 1); + at91_set_deglitch(data->slot[i].detect_pin, + 1); + } + if (gpio_is_valid(data->slot[i].wp_pin)) + at91_set_gpio_input(data->slot[i].wp_pin, 1); + + if (mmc_id == 0) { /* MCI0 */ + switch (i) { + case 0: /* slot A */ + /* CMD */ + at91_set_A_periph(AT91_PIN_PA1, 1); + /* DAT0, maybe DAT1..DAT3 */ + at91_set_A_periph(AT91_PIN_PA0, 1); + if (data->slot[i].bus_width == 4) { + at91_set_A_periph(AT91_PIN_PA3, 1); + at91_set_A_periph(AT91_PIN_PA4, 1); + at91_set_A_periph(AT91_PIN_PA5, 1); + } + slot_count++; + break; + case 1: /* slot B */ + /* CMD */ + at91_set_A_periph(AT91_PIN_PA16, 1); + /* DAT0, maybe DAT1..DAT3 */ + at91_set_A_periph(AT91_PIN_PA17, 1); + if (data->slot[i].bus_width == 4) { + at91_set_A_periph(AT91_PIN_PA18, 1); + at91_set_A_periph(AT91_PIN_PA19, 1); + at91_set_A_periph(AT91_PIN_PA20, 1); + } + slot_count++; + break; + default: + printk(KERN_ERR + "AT91: SD/MMC slot %d not available\n", i); + break; + } + if (slot_count) { + /* CLK */ + at91_set_A_periph(AT91_PIN_PA12, 0); + + mmc0_data = *data; + platform_device_register(&at91sam9263_mmc0_device); + } + } else if (mmc_id == 1) { /* MCI1 */ + switch (i) { + case 0: /* slot A */ + /* CMD */ + at91_set_A_periph(AT91_PIN_PA7, 1); + /* DAT0, maybe DAT1..DAT3 */ + at91_set_A_periph(AT91_PIN_PA8, 1); + if (data->slot[i].bus_width == 4) { + at91_set_A_periph(AT91_PIN_PA9, 1); + at91_set_A_periph(AT91_PIN_PA10, 1); + at91_set_A_periph(AT91_PIN_PA11, 1); + } + slot_count++; + break; + case 1: /* slot B */ + /* CMD */ + at91_set_A_periph(AT91_PIN_PA21, 1); + /* DAT0, maybe DAT1..DAT3 */ + at91_set_A_periph(AT91_PIN_PA22, 1); + if (data->slot[i].bus_width == 4) { + at91_set_A_periph(AT91_PIN_PA23, 1); + at91_set_A_periph(AT91_PIN_PA24, 1); + at91_set_A_periph(AT91_PIN_PA25, 1); + } + slot_count++; + break; + default: + printk(KERN_ERR + "AT91: SD/MMC slot %d not available\n", i); + break; + } + if (slot_count) { + /* CLK */ + at91_set_A_periph(AT91_PIN_PA6, 0); + + mmc1_data = *data; + platform_device_register(&at91sam9263_mmc1_device); + } + } + } +} +#else +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {} +#endif + +/* -------------------------------------------------------------------- * Compact Flash (PCMCIA or IDE) * -------------------------------------------------------------------- */ diff --git a/arch/arm/mach-at91/at91sam9rl_devices.c b/arch/arm/mach-at91/at91sam9rl_devices.c index fe4ae22..83c5845 100644 --- a/arch/arm/mach-at91/at91sam9rl_devices.c +++ b/arch/arm/mach-at91/at91sam9rl_devices.c @@ -228,6 +228,76 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {} /* -------------------------------------------------------------------- + * MMC / SD + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static u64 mmc_dmamask = DMA_BIT_MASK(32); +static struct mci_platform_data mmc_data; + +static struct resource mmc_resources[] = { + [0] = { + .start = AT91SAM9RL_BASE_MCI, + .end = AT91SAM9RL_BASE_MCI + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9RL_ID_MCI, + .end = AT91SAM9RL_ID_MCI, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91sam9rl_mmc_device = { + .name = "atmel_mci", + .id = -1, + .dev = { + .dma_mask = &mmc_dmamask, + .coherent_dma_mask = DMA_BIT_MASK(32), + .platform_data = &mmc_data, + }, + .resource = mmc_resources, + .num_resources = ARRAY_SIZE(mmc_resources), +}; + +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) +{ + if (!data) + return; + + if (data->slot[0].bus_width) { + /* input/irq */ + if (gpio_is_valid(data->slot[0].detect_pin)) { + at91_set_gpio_input(data->slot[0].detect_pin, 1); + at91_set_deglitch(data->slot[0].detect_pin, 1); + } + if (gpio_is_valid(data->slot[0].wp_pin)) + at91_set_gpio_input(data->slot[0].wp_pin, 1); + + /* CLK */ + at91_set_A_periph(AT91_PIN_PA2, 0); + + /* CMD */ + at91_set_A_periph(AT91_PIN_PA1, 1); + + /* DAT0, maybe DAT1..DAT3 */ + at91_set_A_periph(AT91_PIN_PA0, 1); + if (data->slot[0].bus_width == 4) { + at91_set_A_periph(AT91_PIN_PA3, 1); + at91_set_A_periph(AT91_PIN_PA4, 1); + at91_set_A_periph(AT91_PIN_PA5, 1); + } + + mmc_data = *data; + platform_device_register(&at91sam9rl_mmc_device); + } +} +#else +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {} +#endif + + +/* -------------------------------------------------------------------- * NAND / SmartMedia * -------------------------------------------------------------------- */ diff --git a/arch/arm/mach-at91/board-foxg20.c b/arch/arm/mach-at91/board-foxg20.c index caf017f..6cda303 100644 --- a/arch/arm/mach-at91/board-foxg20.c +++ b/arch/arm/mach-at91/board-foxg20.c @@ -123,7 +123,7 @@ static struct at91_udc_data __initdata foxg20_udc_data = { * SPI devices. */ static struct spi_board_info foxg20_spi_devices[] = { -#if !defined(CONFIG_MMC_AT91) +#if !defined(CONFIG_MMC_AT91) && !defined(CONFIG_MMC_ATMELMCI) { .modalias = "mtd_dataflash", .chip_select = 1, @@ -146,6 +146,7 @@ static struct macb_platform_data __initdata foxg20_macb_data = { * MCI (SD/MMC) * det_pin, wp_pin and vcc_pin are not connected */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) static struct at91_mmc_data __initdata foxg20_mmc_data = { .slot_b = 1, .wire4 = 1, @@ -153,6 +154,15 @@ static struct at91_mmc_data __initdata foxg20_mmc_data = { .wp_pin = -EINVAL, .vcc_pin = -EINVAL, }; +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata foxg20_mci0_data = { + .slot[1] = { + .bus_width = 4, + .detect_pin = -EINVAL, + .wp_pin = -EINVAL, + }, +}; +#endif /* @@ -251,7 +261,11 @@ static void __init foxg20_board_init(void) /* Ethernet */ at91_add_device_eth(&foxg20_macb_data); /* MMC */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) at91_add_device_mmc(0, &foxg20_mmc_data); +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &foxg20_mci0_data); +#endif /* I2C */ at91_add_device_i2c(foxg20_i2c_devices, ARRAY_SIZE(foxg20_i2c_devices)); /* LEDs */ diff --git a/arch/arm/mach-at91/board-rm9200ek.c b/arch/arm/mach-at91/board-rm9200ek.c index b2e4fe2..7177aac 100644 --- a/arch/arm/mach-at91/board-rm9200ek.c +++ b/arch/arm/mach-at91/board-rm9200ek.c @@ -83,6 +83,7 @@ static struct at91_udc_data __initdata ek_udc_data = { }; #ifndef CONFIG_MTD_AT91_DATAFLASH_CARD +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) static struct at91_mmc_data __initdata ek_mmc_data = { .det_pin = AT91_PIN_PB27, .slot_b = 0, @@ -90,6 +91,15 @@ static struct at91_mmc_data __initdata ek_mmc_data = { .wp_pin = AT91_PIN_PA17, .vcc_pin = -EINVAL, }; +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata ek_mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PB27, + .wp_pin = AT91_PIN_PA17, + } +}; +#endif #endif static struct spi_board_info ek_spi_devices[] = { @@ -180,7 +190,11 @@ static void __init ek_board_init(void) #else /* MMC */ at91_set_gpio_output(AT91_PIN_PB22, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) at91_add_device_mmc(0, &ek_mmc_data); +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &ek_mci0_data); +#endif #endif /* NOR Flash */ platform_device_register(&ek_flash); diff --git a/arch/arm/mach-at91/board-sam9-l9260.c b/arch/arm/mach-at91/board-sam9-l9260.c index e8b116b..4a5786b 100644 --- a/arch/arm/mach-at91/board-sam9-l9260.c +++ b/arch/arm/mach-at91/board-sam9-l9260.c @@ -89,7 +89,7 @@ static struct at91_udc_data __initdata ek_udc_data = { * SPI devices. */ static struct spi_board_info ek_spi_devices[] = { -#if !defined(CONFIG_MMC_AT91) +#if !defined(CONFIG_MMC_AT91) && !defined(CONFIG_MMC_ATMELMCI) { /* DataFlash chip */ .modalias = "mtd_dataflash", .chip_select = 1, @@ -174,6 +174,7 @@ static void __init ek_add_device_nand(void) /* * MCI (SD/MMC) */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) static struct at91_mmc_data __initdata ek_mmc_data = { .slot_b = 1, .wire4 = 1, @@ -181,6 +182,15 @@ static struct at91_mmc_data __initdata ek_mmc_data = { .wp_pin = AT91_PIN_PC4, .vcc_pin = -EINVAL, }; +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata mci0_data = { + .slot[1] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PC8, + .wp_pin = AT91_PIN_PC4, + }, +}; +#endif static void __init ek_board_init(void) { @@ -197,7 +207,11 @@ static void __init ek_board_init(void) /* Ethernet */ at91_add_device_eth(&ek_macb_data); /* MMC */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) at91_add_device_mmc(0, &ek_mmc_data); +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &ek_mci0_data); +#endif /* I2C */ at91_add_device_i2c(NULL, 0); } diff --git a/arch/arm/mach-at91/board-sam9260ek.c b/arch/arm/mach-at91/board-sam9260ek.c index d5aec55..b6ce2df 100644 --- a/arch/arm/mach-at91/board-sam9260ek.c +++ b/arch/arm/mach-at91/board-sam9260ek.c @@ -121,7 +121,7 @@ static void __init at73c213_set_clk(struct at73c213_board_info *info) {} * SPI devices. */ static struct spi_board_info ek_spi_devices[] = { -#if !defined(CONFIG_MMC_AT91) +#if !defined(CONFIG_MMC_AT91) && !defined(CONFIG_MMC_ATMELMCI) { /* DataFlash chip */ .modalias = "mtd_dataflash", .chip_select = 1, @@ -224,6 +224,7 @@ static void __init ek_add_device_nand(void) /* * MCI (SD/MMC) */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) static struct at91_mmc_data __initdata ek_mmc_data = { .slot_b = 1, .wire4 = 1, @@ -231,6 +232,15 @@ static struct at91_mmc_data __initdata ek_mmc_data = { .wp_pin = -EINVAL, .vcc_pin = -EINVAL, }; +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata mci0_data = { + .slot[1] = { + .bus_width = 4, + .detect_pin = -EINVAL, + .wp_pin = -EINVAL, + }, +}; +#endif /* @@ -332,7 +342,11 @@ static void __init ek_board_init(void) /* Ethernet */ at91_add_device_eth(&ek_macb_data); /* MMC */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) at91_add_device_mmc(0, &ek_mmc_data); +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &ek_mci0_data); +#endif /* I2C */ at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices)); /* SSC (to AT73C213) */ diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c index 065fed3..797dd7c 100644 --- a/arch/arm/mach-at91/board-sam9261ek.c +++ b/arch/arm/mach-at91/board-sam9261ek.c @@ -344,6 +344,7 @@ static struct spi_board_info ek_spi_devices[] = { #else /* CONFIG_SPI_ATMEL_* */ /* spi0 and mmc/sd share the same PIO pins: cannot be used at the same time */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) /* * MCI (SD/MMC) * det_pin, wp_pin and vcc_pin are not connected @@ -354,6 +355,15 @@ static struct at91_mmc_data __initdata ek_mmc_data = { .wp_pin = -EINVAL, .vcc_pin = -EINVAL, }; +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = -EINVAL, + .wp_pin = -EINVAL, + }, +}; +#endif #endif /* CONFIG_SPI_ATMEL_* */ @@ -601,7 +611,11 @@ static void __init ek_board_init(void) at91_add_device_ssc(AT91SAM9261_ID_SSC1, ATMEL_SSC_TX); #else /* MMC */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) at91_add_device_mmc(0, &ek_mmc_data); +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &mci0_data); +#endif #endif /* LCD Controller */ at91_add_device_lcdc(&ek_lcdc_data); diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c index 2ffe50f..8080d02 100644 --- a/arch/arm/mach-at91/board-sam9263ek.c +++ b/arch/arm/mach-at91/board-sam9263ek.c @@ -149,12 +149,22 @@ static struct spi_board_info ek_spi_devices[] = { /* * MCI (SD/MMC) */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) static struct at91_mmc_data __initdata ek_mmc_data = { .wire4 = 1, .det_pin = AT91_PIN_PE18, .wp_pin = AT91_PIN_PE19, .vcc_pin = -EINVAL, }; +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata mci1_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PE18, + .wp_pin = AT91_PIN_PE19, + }, +}; +#endif /* @@ -423,7 +433,11 @@ static void __init ek_board_init(void) /* Touchscreen */ ek_add_device_ts(); /* MMC */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) at91_add_device_mmc(1, &ek_mmc_data); +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(1, &mci1_data); +#endif /* Ethernet */ at91_add_device_eth(&ek_macb_data); /* NAND */ diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c index b109ce2..bb06521 100644 --- a/arch/arm/mach-at91/board-sam9rlek.c +++ b/arch/arm/mach-at91/board-sam9rlek.c @@ -64,12 +64,22 @@ static struct usba_platform_data __initdata ek_usba_udc_data = { /* * MCI (SD/MMC) */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) static struct at91_mmc_data __initdata ek_mmc_data = { .wire4 = 1, .det_pin = AT91_PIN_PA15, .wp_pin = -EINVAL, .vcc_pin = -EINVAL, }; +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PA15, + .wp_pin = -EINVAL, + }, +}; +#endif /* @@ -306,7 +316,11 @@ static void __init ek_board_init(void) /* SPI */ at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); /* MMC */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) at91_add_device_mmc(0, &ek_mmc_data); +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &mci0_data); +#endif /* LCD Controller */ at91_add_device_lcdc(&ek_lcdc_data); /* AC97 */ diff --git a/arch/arm/mach-at91/board-usb-a926x.c b/arch/arm/mach-at91/board-usb-a926x.c index b7483a3..879e34e 100644 --- a/arch/arm/mach-at91/board-usb-a926x.c +++ b/arch/arm/mach-at91/board-usb-a926x.c @@ -114,7 +114,7 @@ static struct mmc_spi_platform_data at91_mmc_spi_pdata = { * SPI devices. */ static struct spi_board_info usb_a9263_spi_devices[] = { -#if !defined(CONFIG_MMC_AT91) +#if !defined(CONFIG_MMC_AT91) && !defined(CONFIG_MMC_ATMELMCI) { /* DataFlash chip */ .modalias = "mtd_dataflash", .chip_select = 0, -- 1.7.5.4 ^ permalink raw reply related [flat|nested] 28+ messages in thread
* Re: [PATCH 1/2] ARM: at91: add atmel-mci support for chips and boards which can use it 2012-05-16 15:51 ` ludovic.desroches at atmel.com @ 2012-05-21 10:17 ` Nicolas Ferre -1 siblings, 0 replies; 28+ messages in thread From: Nicolas Ferre @ 2012-05-21 10:17 UTC (permalink / raw) To: ludovic.desroches; +Cc: linux-mmc, linux-arm-kernel, plagnioj On 05/16/2012 05:51 PM, ludovic.desroches@atmel.com : > From: Ludovic Desroches <ludovic.desroches@atmel.com> > > Since atmel-mci driver supports all atmel mci version excepted the rm9200 one, > use it instead of at91_mci driver. > > Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> > --- > arch/arm/mach-at91/at91rm9200_devices.c | 99 ++++++++++++++++++ > arch/arm/mach-at91/at91sam9261_devices.c | 67 ++++++++++++ > arch/arm/mach-at91/at91sam9263.c | 2 + > arch/arm/mach-at91/at91sam9263_devices.c | 164 ++++++++++++++++++++++++++++++ > arch/arm/mach-at91/at91sam9rl_devices.c | 70 +++++++++++++ > arch/arm/mach-at91/board-foxg20.c | 16 +++- > arch/arm/mach-at91/board-rm9200ek.c | 14 +++ > arch/arm/mach-at91/board-sam9-l9260.c | 16 +++- > arch/arm/mach-at91/board-sam9260ek.c | 16 +++- > arch/arm/mach-at91/board-sam9261ek.c | 14 +++ > arch/arm/mach-at91/board-sam9263ek.c | 14 +++ > arch/arm/mach-at91/board-sam9rlek.c | 14 +++ > arch/arm/mach-at91/board-usb-a926x.c | 2 +- > 13 files changed, 504 insertions(+), 4 deletions(-) > > diff --git a/arch/arm/mach-at91/at91rm9200_devices.c b/arch/arm/mach-at91/at91rm9200_devices.c > index 05774e5..2c13783 100644 > --- a/arch/arm/mach-at91/at91rm9200_devices.c > +++ b/arch/arm/mach-at91/at91rm9200_devices.c > @@ -374,6 +374,105 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {} > > > /* -------------------------------------------------------------------- > + * MMC / SD > + * -------------------------------------------------------------------- */ > + > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static u64 mmc_dmamask = DMA_BIT_MASK(32); > +static struct mci_platform_data mmc_data; > + > +static struct resource mmc_resources[] = { > + [0] = { > + .start = AT91RM9200_BASE_MCI, > + .end = AT91RM9200_BASE_MCI + SZ_16K - 1, > + .flags = IORESOURCE_MEM, > + }, > + [1] = { > + .start = AT91RM9200_ID_MCI, > + .end = AT91RM9200_ID_MCI, > + .flags = IORESOURCE_IRQ, > + }, > +}; > + > +static struct platform_device at91rm9200_mmc_device = { > + .name = "atmel_mci", > + .id = -1, > + .dev = { > + .dma_mask = &mmc_dmamask, > + .coherent_dma_mask = DMA_BIT_MASK(32), > + .platform_data = &mmc_data, > + }, > + .resource = mmc_resources, > + .num_resources = ARRAY_SIZE(mmc_resources), > +}; > + > +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) > +{ > + unsigned int i; > + unsigned int slot_count = 0; > + > + if (!data) > + return; > + > + for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) { > + > + if (!data->slot[i].bus_width) > + continue; > + > + /* input/irq */ > + if (gpio_is_valid(data->slot[i].detect_pin)) { > + at91_set_gpio_input(data->slot[i].detect_pin, 1); > + at91_set_deglitch(data->slot[i].detect_pin, 1); > + } > + if (gpio_is_valid(data->slot[i].wp_pin)) > + at91_set_gpio_input(data->slot[i].wp_pin, 1); > + > + switch (i) { > + case 0: /* slot A */ > + /* CMD */ > + at91_set_A_periph(AT91_PIN_PA28, 1); > + /* DAT0, maybe DAT1..DAT3 */ > + at91_set_A_periph(AT91_PIN_PA29, 1); > + if (data->slot[i].bus_width == 4) { > + at91_set_B_periph(AT91_PIN_PB3, 1); > + at91_set_B_periph(AT91_PIN_PB4, 1); > + at91_set_B_periph(AT91_PIN_PB5, 1); > + } > + slot_count++; > + break; > + case 1: /* slot B */ > + /* CMD */ > + at91_set_B_periph(AT91_PIN_PA8, 1); > + /* DAT0, maybe DAT1..DAT3 */ > + at91_set_B_periph(AT91_PIN_PA9, 1); > + if (data->slot[i].bus_width == 4) { > + at91_set_B_periph(AT91_PIN_PA10, 1); > + at91_set_B_periph(AT91_PIN_PA11, 1); > + at91_set_B_periph(AT91_PIN_PA12, 1); > + } > + slot_count++; > + break; > + default: > + printk(KERN_ERR > + "AT91: SD/MMC slot %d not available\n", i); > + break; > + } > + if (slot_count) { > + /* CLK */ > + at91_set_A_periph(AT91_PIN_PA27, 0); > + > + mmc_data = *data; > + platform_device_register(&at91rm9200_mmc_device); > + } > + } > + > +} > +#else > +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {} > +#endif > + > + > +/* -------------------------------------------------------------------- > * NAND / SmartMedia > * -------------------------------------------------------------------- */ > > diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c > index 4db961a..0817854 100644 > --- a/arch/arm/mach-at91/at91sam9261_devices.c > +++ b/arch/arm/mach-at91/at91sam9261_devices.c > @@ -202,7 +202,74 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) > void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {} > #endif > > +/* -------------------------------------------------------------------- > + * MMC / SD Slot for Atmel MCI Driver > + * -------------------------------------------------------------------- */ > + > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static u64 mmc_dmamask = DMA_BIT_MASK(32); > +static struct mci_platform_data mmc_data; > + > +static struct resource mmc_resources[] = { > + [0] = { > + .start = AT91SAM9261_BASE_MCI, > + .end = AT91SAM9261_BASE_MCI + SZ_16K - 1, > + .flags = IORESOURCE_MEM, > + }, > + [1] = { > + .start = AT91SAM9261_ID_MCI, > + .end = AT91SAM9261_ID_MCI, > + .flags = IORESOURCE_IRQ, > + }, > +}; > + > +static struct platform_device at91sam9261_mmc_device = { > + .name = "atmel_mci", > + .id = -1, > + .dev = { > + .dma_mask = &mmc_dmamask, > + .coherent_dma_mask = DMA_BIT_MASK(32), > + .platform_data = &mmc_data, > + }, > + .resource = mmc_resources, > + .num_resources = ARRAY_SIZE(mmc_resources), > +}; > + > +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) > +{ > + if (!data) > + return; > > + if (data->slot[0].bus_width) { > + /* input/irq */ > + if (gpio_is_valid(data->slot[0].detect_pin)) { > + at91_set_gpio_input(data->slot[0].detect_pin, 1); > + at91_set_deglitch(data->slot[0].detect_pin, 1); > + } > + if (gpio_is_valid(data->slot[0].wp_pin)) > + at91_set_gpio_input(data->slot[0].wp_pin, 1); > + > + /* CLK */ > + at91_set_B_periph(AT91_PIN_PA2, 0); > + > + /* CMD */ > + at91_set_B_periph(AT91_PIN_PA1, 1); > + > + /* DAT0, maybe DAT1..DAT3 */ > + at91_set_B_periph(AT91_PIN_PA0, 1); > + if (data->slot[0].bus_width == 4) { > + at91_set_B_periph(AT91_PIN_PA4, 1); > + at91_set_B_periph(AT91_PIN_PA5, 1); > + at91_set_B_periph(AT91_PIN_PA6, 1); > + } > + > + mmc_data = *data; > + platform_device_register(&at91sam9261_mmc_device); > + } > +} > +#else > +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {} > +#endif > /* -------------------------------------------------------------------- > * NAND / SmartMedia > * -------------------------------------------------------------------- */ > diff --git a/arch/arm/mach-at91/at91sam9263.c b/arch/arm/mach-at91/at91sam9263.c > index ef301be..053e47a 100644 > --- a/arch/arm/mach-at91/at91sam9263.c > +++ b/arch/arm/mach-at91/at91sam9263.c > @@ -189,6 +189,8 @@ static struct clk_lookup periph_clocks_lookups[] = { > CLKDEV_CON_DEV_ID("pclk", "ssc.1", &ssc1_clk), > CLKDEV_CON_DEV_ID("mci_clk", "at91_mci.0", &mmc0_clk), > CLKDEV_CON_DEV_ID("mci_clk", "at91_mci.1", &mmc1_clk), > + CLKDEV_CON_DEV_ID("mci_clk", "atmel_mci.0", &mmc0_clk), > + CLKDEV_CON_DEV_ID("mci_clk", "atmel_mci.1", &mmc1_clk), > CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.0", &spi0_clk), > CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.1", &spi1_clk), > CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tcb_clk), > diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c > index fe99206..617fbfc 100644 > --- a/arch/arm/mach-at91/at91sam9263_devices.c > +++ b/arch/arm/mach-at91/at91sam9263_devices.c > @@ -354,6 +354,170 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {} > #endif > > /* -------------------------------------------------------------------- > + * MMC / SD > + * -------------------------------------------------------------------- */ > + > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static u64 mmc_dmamask = DMA_BIT_MASK(32); > +static struct mci_platform_data mmc0_data, mmc1_data; > + > +static struct resource mmc0_resources[] = { > + [0] = { > + .start = AT91SAM9263_BASE_MCI0, > + .end = AT91SAM9263_BASE_MCI0 + SZ_16K - 1, > + .flags = IORESOURCE_MEM, > + }, > + [1] = { > + .start = AT91SAM9263_ID_MCI0, > + .end = AT91SAM9263_ID_MCI0, > + .flags = IORESOURCE_IRQ, > + }, > +}; > + > +static struct platform_device at91sam9263_mmc0_device = { > + .name = "atmel_mci", > + .id = 0, > + .dev = { > + .dma_mask = &mmc_dmamask, > + .coherent_dma_mask = DMA_BIT_MASK(32), > + .platform_data = &mmc0_data, > + }, > + .resource = mmc0_resources, > + .num_resources = ARRAY_SIZE(mmc0_resources), > +}; > + > +static struct resource mmc1_resources[] = { > + [0] = { > + .start = AT91SAM9263_BASE_MCI1, > + .end = AT91SAM9263_BASE_MCI1 + SZ_16K - 1, > + .flags = IORESOURCE_MEM, > + }, > + [1] = { > + .start = AT91SAM9263_ID_MCI1, > + .end = AT91SAM9263_ID_MCI1, > + .flags = IORESOURCE_IRQ, > + }, > +}; > + > +static struct platform_device at91sam9263_mmc1_device = { > + .name = "atmel_mci", > + .id = 1, > + .dev = { > + .dma_mask = &mmc_dmamask, > + .coherent_dma_mask = DMA_BIT_MASK(32), > + .platform_data = &mmc1_data, > + }, > + .resource = mmc1_resources, > + .num_resources = ARRAY_SIZE(mmc1_resources), > +}; > + > +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) > +{ > + unsigned int i; > + unsigned int slot_count = 0; > + > + if (!data) > + return; > + > + for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) { > + > + if (!data->slot[i].bus_width) > + continue; > + > + /* input/irq */ > + if (gpio_is_valid(data->slot[i].detect_pin)) { > + at91_set_gpio_input(data->slot[i].detect_pin, > + 1); > + at91_set_deglitch(data->slot[i].detect_pin, > + 1); > + } > + if (gpio_is_valid(data->slot[i].wp_pin)) > + at91_set_gpio_input(data->slot[i].wp_pin, 1); > + > + if (mmc_id == 0) { /* MCI0 */ > + switch (i) { > + case 0: /* slot A */ > + /* CMD */ > + at91_set_A_periph(AT91_PIN_PA1, 1); > + /* DAT0, maybe DAT1..DAT3 */ > + at91_set_A_periph(AT91_PIN_PA0, 1); > + if (data->slot[i].bus_width == 4) { > + at91_set_A_periph(AT91_PIN_PA3, 1); > + at91_set_A_periph(AT91_PIN_PA4, 1); > + at91_set_A_periph(AT91_PIN_PA5, 1); > + } > + slot_count++; > + break; > + case 1: /* slot B */ > + /* CMD */ > + at91_set_A_periph(AT91_PIN_PA16, 1); > + /* DAT0, maybe DAT1..DAT3 */ > + at91_set_A_periph(AT91_PIN_PA17, 1); > + if (data->slot[i].bus_width == 4) { > + at91_set_A_periph(AT91_PIN_PA18, 1); > + at91_set_A_periph(AT91_PIN_PA19, 1); > + at91_set_A_periph(AT91_PIN_PA20, 1); > + } > + slot_count++; > + break; > + default: > + printk(KERN_ERR > + "AT91: SD/MMC slot %d not available\n", i); > + break; > + } > + if (slot_count) { > + /* CLK */ > + at91_set_A_periph(AT91_PIN_PA12, 0); > + > + mmc0_data = *data; > + platform_device_register(&at91sam9263_mmc0_device); > + } > + } else if (mmc_id == 1) { /* MCI1 */ > + switch (i) { > + case 0: /* slot A */ > + /* CMD */ > + at91_set_A_periph(AT91_PIN_PA7, 1); > + /* DAT0, maybe DAT1..DAT3 */ > + at91_set_A_periph(AT91_PIN_PA8, 1); > + if (data->slot[i].bus_width == 4) { > + at91_set_A_periph(AT91_PIN_PA9, 1); > + at91_set_A_periph(AT91_PIN_PA10, 1); > + at91_set_A_periph(AT91_PIN_PA11, 1); > + } > + slot_count++; > + break; > + case 1: /* slot B */ > + /* CMD */ > + at91_set_A_periph(AT91_PIN_PA21, 1); > + /* DAT0, maybe DAT1..DAT3 */ > + at91_set_A_periph(AT91_PIN_PA22, 1); > + if (data->slot[i].bus_width == 4) { > + at91_set_A_periph(AT91_PIN_PA23, 1); > + at91_set_A_periph(AT91_PIN_PA24, 1); > + at91_set_A_periph(AT91_PIN_PA25, 1); > + } > + slot_count++; > + break; > + default: > + printk(KERN_ERR > + "AT91: SD/MMC slot %d not available\n", i); > + break; > + } > + if (slot_count) { > + /* CLK */ > + at91_set_A_periph(AT91_PIN_PA6, 0); > + > + mmc1_data = *data; > + platform_device_register(&at91sam9263_mmc1_device); > + } > + } > + } > +} > +#else > +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {} > +#endif > + > +/* -------------------------------------------------------------------- > * Compact Flash (PCMCIA or IDE) > * -------------------------------------------------------------------- */ > > diff --git a/arch/arm/mach-at91/at91sam9rl_devices.c b/arch/arm/mach-at91/at91sam9rl_devices.c > index fe4ae22..83c5845 100644 > --- a/arch/arm/mach-at91/at91sam9rl_devices.c > +++ b/arch/arm/mach-at91/at91sam9rl_devices.c > @@ -228,6 +228,76 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {} > > > /* -------------------------------------------------------------------- > + * MMC / SD > + * -------------------------------------------------------------------- */ > + > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static u64 mmc_dmamask = DMA_BIT_MASK(32); > +static struct mci_platform_data mmc_data; > + > +static struct resource mmc_resources[] = { > + [0] = { > + .start = AT91SAM9RL_BASE_MCI, > + .end = AT91SAM9RL_BASE_MCI + SZ_16K - 1, > + .flags = IORESOURCE_MEM, > + }, > + [1] = { > + .start = AT91SAM9RL_ID_MCI, > + .end = AT91SAM9RL_ID_MCI, > + .flags = IORESOURCE_IRQ, > + }, > +}; > + > +static struct platform_device at91sam9rl_mmc_device = { > + .name = "atmel_mci", > + .id = -1, > + .dev = { > + .dma_mask = &mmc_dmamask, > + .coherent_dma_mask = DMA_BIT_MASK(32), > + .platform_data = &mmc_data, > + }, > + .resource = mmc_resources, > + .num_resources = ARRAY_SIZE(mmc_resources), > +}; > + > +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) > +{ > + if (!data) > + return; > + > + if (data->slot[0].bus_width) { > + /* input/irq */ > + if (gpio_is_valid(data->slot[0].detect_pin)) { > + at91_set_gpio_input(data->slot[0].detect_pin, 1); > + at91_set_deglitch(data->slot[0].detect_pin, 1); > + } > + if (gpio_is_valid(data->slot[0].wp_pin)) > + at91_set_gpio_input(data->slot[0].wp_pin, 1); > + > + /* CLK */ > + at91_set_A_periph(AT91_PIN_PA2, 0); > + > + /* CMD */ > + at91_set_A_periph(AT91_PIN_PA1, 1); > + > + /* DAT0, maybe DAT1..DAT3 */ > + at91_set_A_periph(AT91_PIN_PA0, 1); > + if (data->slot[0].bus_width == 4) { > + at91_set_A_periph(AT91_PIN_PA3, 1); > + at91_set_A_periph(AT91_PIN_PA4, 1); > + at91_set_A_periph(AT91_PIN_PA5, 1); > + } > + > + mmc_data = *data; > + platform_device_register(&at91sam9rl_mmc_device); > + } > +} > +#else > +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {} > +#endif > + > + > +/* -------------------------------------------------------------------- > * NAND / SmartMedia > * -------------------------------------------------------------------- */ > > diff --git a/arch/arm/mach-at91/board-foxg20.c b/arch/arm/mach-at91/board-foxg20.c > index caf017f..6cda303 100644 > --- a/arch/arm/mach-at91/board-foxg20.c > +++ b/arch/arm/mach-at91/board-foxg20.c > @@ -123,7 +123,7 @@ static struct at91_udc_data __initdata foxg20_udc_data = { > * SPI devices. > */ > static struct spi_board_info foxg20_spi_devices[] = { > -#if !defined(CONFIG_MMC_AT91) > +#if !defined(CONFIG_MMC_AT91) && !defined(CONFIG_MMC_ATMELMCI) > { > .modalias = "mtd_dataflash", > .chip_select = 1, > @@ -146,6 +146,7 @@ static struct macb_platform_data __initdata foxg20_macb_data = { > * MCI (SD/MMC) > * det_pin, wp_pin and vcc_pin are not connected > */ > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > static struct at91_mmc_data __initdata foxg20_mmc_data = { > .slot_b = 1, > .wire4 = 1, > @@ -153,6 +154,15 @@ static struct at91_mmc_data __initdata foxg20_mmc_data = { > .wp_pin = -EINVAL, > .vcc_pin = -EINVAL, > }; > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata foxg20_mci0_data = { > + .slot[1] = { > + .bus_width = 4, > + .detect_pin = -EINVAL, > + .wp_pin = -EINVAL, > + }, > +}; > +#endif > > > /* > @@ -251,7 +261,11 @@ static void __init foxg20_board_init(void) > /* Ethernet */ > at91_add_device_eth(&foxg20_macb_data); > /* MMC */ > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > at91_add_device_mmc(0, &foxg20_mmc_data); > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0, &foxg20_mci0_data); > +#endif > /* I2C */ > at91_add_device_i2c(foxg20_i2c_devices, ARRAY_SIZE(foxg20_i2c_devices)); > /* LEDs */ > diff --git a/arch/arm/mach-at91/board-rm9200ek.c b/arch/arm/mach-at91/board-rm9200ek.c > index b2e4fe2..7177aac 100644 > --- a/arch/arm/mach-at91/board-rm9200ek.c > +++ b/arch/arm/mach-at91/board-rm9200ek.c > @@ -83,6 +83,7 @@ static struct at91_udc_data __initdata ek_udc_data = { > }; > > #ifndef CONFIG_MTD_AT91_DATAFLASH_CARD > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > static struct at91_mmc_data __initdata ek_mmc_data = { > .det_pin = AT91_PIN_PB27, > .slot_b = 0, > @@ -90,6 +91,15 @@ static struct at91_mmc_data __initdata ek_mmc_data = { > .wp_pin = AT91_PIN_PA17, > .vcc_pin = -EINVAL, > }; > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata ek_mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PB27, > + .wp_pin = AT91_PIN_PA17, > + } > +}; > +#endif > #endif > > static struct spi_board_info ek_spi_devices[] = { > @@ -180,7 +190,11 @@ static void __init ek_board_init(void) > #else > /* MMC */ > at91_set_gpio_output(AT91_PIN_PB22, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */ > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > at91_add_device_mmc(0, &ek_mmc_data); > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0, &ek_mci0_data); > +#endif > #endif > /* NOR Flash */ > platform_device_register(&ek_flash); > diff --git a/arch/arm/mach-at91/board-sam9-l9260.c b/arch/arm/mach-at91/board-sam9-l9260.c > index e8b116b..4a5786b 100644 > --- a/arch/arm/mach-at91/board-sam9-l9260.c > +++ b/arch/arm/mach-at91/board-sam9-l9260.c > @@ -89,7 +89,7 @@ static struct at91_udc_data __initdata ek_udc_data = { > * SPI devices. > */ > static struct spi_board_info ek_spi_devices[] = { > -#if !defined(CONFIG_MMC_AT91) > +#if !defined(CONFIG_MMC_AT91) && !defined(CONFIG_MMC_ATMELMCI) > { /* DataFlash chip */ > .modalias = "mtd_dataflash", > .chip_select = 1, > @@ -174,6 +174,7 @@ static void __init ek_add_device_nand(void) > /* > * MCI (SD/MMC) > */ > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > static struct at91_mmc_data __initdata ek_mmc_data = { > .slot_b = 1, > .wire4 = 1, > @@ -181,6 +182,15 @@ static struct at91_mmc_data __initdata ek_mmc_data = { > .wp_pin = AT91_PIN_PC4, > .vcc_pin = -EINVAL, > }; > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata mci0_data = { > + .slot[1] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PC8, > + .wp_pin = AT91_PIN_PC4, > + }, > +}; > +#endif > > static void __init ek_board_init(void) > { > @@ -197,7 +207,11 @@ static void __init ek_board_init(void) > /* Ethernet */ > at91_add_device_eth(&ek_macb_data); > /* MMC */ > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > at91_add_device_mmc(0, &ek_mmc_data); > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0, &ek_mci0_data); > +#endif > /* I2C */ > at91_add_device_i2c(NULL, 0); > } > diff --git a/arch/arm/mach-at91/board-sam9260ek.c b/arch/arm/mach-at91/board-sam9260ek.c > index d5aec55..b6ce2df 100644 > --- a/arch/arm/mach-at91/board-sam9260ek.c > +++ b/arch/arm/mach-at91/board-sam9260ek.c > @@ -121,7 +121,7 @@ static void __init at73c213_set_clk(struct at73c213_board_info *info) {} > * SPI devices. > */ > static struct spi_board_info ek_spi_devices[] = { > -#if !defined(CONFIG_MMC_AT91) > +#if !defined(CONFIG_MMC_AT91) && !defined(CONFIG_MMC_ATMELMCI) > { /* DataFlash chip */ > .modalias = "mtd_dataflash", > .chip_select = 1, > @@ -224,6 +224,7 @@ static void __init ek_add_device_nand(void) > /* > * MCI (SD/MMC) > */ > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > static struct at91_mmc_data __initdata ek_mmc_data = { > .slot_b = 1, > .wire4 = 1, > @@ -231,6 +232,15 @@ static struct at91_mmc_data __initdata ek_mmc_data = { > .wp_pin = -EINVAL, > .vcc_pin = -EINVAL, > }; > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata mci0_data = { > + .slot[1] = { > + .bus_width = 4, > + .detect_pin = -EINVAL, > + .wp_pin = -EINVAL, > + }, > +}; > +#endif > > > /* > @@ -332,7 +342,11 @@ static void __init ek_board_init(void) > /* Ethernet */ > at91_add_device_eth(&ek_macb_data); > /* MMC */ > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > at91_add_device_mmc(0, &ek_mmc_data); > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0, &ek_mci0_data); > +#endif > /* I2C */ > at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices)); > /* SSC (to AT73C213) */ > diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c > index 065fed3..797dd7c 100644 > --- a/arch/arm/mach-at91/board-sam9261ek.c > +++ b/arch/arm/mach-at91/board-sam9261ek.c > @@ -344,6 +344,7 @@ static struct spi_board_info ek_spi_devices[] = { > #else /* CONFIG_SPI_ATMEL_* */ > /* spi0 and mmc/sd share the same PIO pins: cannot be used at the same time */ > > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > /* > * MCI (SD/MMC) > * det_pin, wp_pin and vcc_pin are not connected > @@ -354,6 +355,15 @@ static struct at91_mmc_data __initdata ek_mmc_data = { > .wp_pin = -EINVAL, > .vcc_pin = -EINVAL, > }; > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = -EINVAL, > + .wp_pin = -EINVAL, > + }, > +}; > +#endif > > #endif /* CONFIG_SPI_ATMEL_* */ > > @@ -601,7 +611,11 @@ static void __init ek_board_init(void) > at91_add_device_ssc(AT91SAM9261_ID_SSC1, ATMEL_SSC_TX); > #else > /* MMC */ > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > at91_add_device_mmc(0, &ek_mmc_data); > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0, &mci0_data); > +#endif > #endif > /* LCD Controller */ > at91_add_device_lcdc(&ek_lcdc_data); > diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c > index 2ffe50f..8080d02 100644 > --- a/arch/arm/mach-at91/board-sam9263ek.c > +++ b/arch/arm/mach-at91/board-sam9263ek.c > @@ -149,12 +149,22 @@ static struct spi_board_info ek_spi_devices[] = { > /* > * MCI (SD/MMC) > */ > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > static struct at91_mmc_data __initdata ek_mmc_data = { > .wire4 = 1, > .det_pin = AT91_PIN_PE18, > .wp_pin = AT91_PIN_PE19, > .vcc_pin = -EINVAL, > }; > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata mci1_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PE18, > + .wp_pin = AT91_PIN_PE19, > + }, > +}; > +#endif > > > /* > @@ -423,7 +433,11 @@ static void __init ek_board_init(void) > /* Touchscreen */ > ek_add_device_ts(); > /* MMC */ > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > at91_add_device_mmc(1, &ek_mmc_data); > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(1, &mci1_data); > +#endif > /* Ethernet */ > at91_add_device_eth(&ek_macb_data); > /* NAND */ > diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c > index b109ce2..bb06521 100644 > --- a/arch/arm/mach-at91/board-sam9rlek.c > +++ b/arch/arm/mach-at91/board-sam9rlek.c > @@ -64,12 +64,22 @@ static struct usba_platform_data __initdata ek_usba_udc_data = { > /* > * MCI (SD/MMC) > */ > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > static struct at91_mmc_data __initdata ek_mmc_data = { > .wire4 = 1, > .det_pin = AT91_PIN_PA15, > .wp_pin = -EINVAL, > .vcc_pin = -EINVAL, > }; > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PA15, > + .wp_pin = -EINVAL, > + }, > +}; > +#endif > > > /* > @@ -306,7 +316,11 @@ static void __init ek_board_init(void) > /* SPI */ > at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); > /* MMC */ > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > at91_add_device_mmc(0, &ek_mmc_data); > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0, &mci0_data); > +#endif > /* LCD Controller */ > at91_add_device_lcdc(&ek_lcdc_data); > /* AC97 */ > diff --git a/arch/arm/mach-at91/board-usb-a926x.c b/arch/arm/mach-at91/board-usb-a926x.c > index b7483a3..879e34e 100644 > --- a/arch/arm/mach-at91/board-usb-a926x.c > +++ b/arch/arm/mach-at91/board-usb-a926x.c > @@ -114,7 +114,7 @@ static struct mmc_spi_platform_data at91_mmc_spi_pdata = { > * SPI devices. > */ > static struct spi_board_info usb_a9263_spi_devices[] = { > -#if !defined(CONFIG_MMC_AT91) > +#if !defined(CONFIG_MMC_AT91) && !defined(CONFIG_MMC_ATMELMCI) > { /* DataFlash chip */ > .modalias = "mtd_dataflash", > .chip_select = 0, -- Nicolas Ferre ^ permalink raw reply [flat|nested] 28+ messages in thread
* [PATCH 1/2] ARM: at91: add atmel-mci support for chips and boards which can use it @ 2012-05-21 10:17 ` Nicolas Ferre 0 siblings, 0 replies; 28+ messages in thread From: Nicolas Ferre @ 2012-05-21 10:17 UTC (permalink / raw) To: linux-arm-kernel On 05/16/2012 05:51 PM, ludovic.desroches at atmel.com : > From: Ludovic Desroches <ludovic.desroches@atmel.com> > > Since atmel-mci driver supports all atmel mci version excepted the rm9200 one, > use it instead of at91_mci driver. > > Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> > --- > arch/arm/mach-at91/at91rm9200_devices.c | 99 ++++++++++++++++++ > arch/arm/mach-at91/at91sam9261_devices.c | 67 ++++++++++++ > arch/arm/mach-at91/at91sam9263.c | 2 + > arch/arm/mach-at91/at91sam9263_devices.c | 164 ++++++++++++++++++++++++++++++ > arch/arm/mach-at91/at91sam9rl_devices.c | 70 +++++++++++++ > arch/arm/mach-at91/board-foxg20.c | 16 +++- > arch/arm/mach-at91/board-rm9200ek.c | 14 +++ > arch/arm/mach-at91/board-sam9-l9260.c | 16 +++- > arch/arm/mach-at91/board-sam9260ek.c | 16 +++- > arch/arm/mach-at91/board-sam9261ek.c | 14 +++ > arch/arm/mach-at91/board-sam9263ek.c | 14 +++ > arch/arm/mach-at91/board-sam9rlek.c | 14 +++ > arch/arm/mach-at91/board-usb-a926x.c | 2 +- > 13 files changed, 504 insertions(+), 4 deletions(-) > > diff --git a/arch/arm/mach-at91/at91rm9200_devices.c b/arch/arm/mach-at91/at91rm9200_devices.c > index 05774e5..2c13783 100644 > --- a/arch/arm/mach-at91/at91rm9200_devices.c > +++ b/arch/arm/mach-at91/at91rm9200_devices.c > @@ -374,6 +374,105 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {} > > > /* -------------------------------------------------------------------- > + * MMC / SD > + * -------------------------------------------------------------------- */ > + > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static u64 mmc_dmamask = DMA_BIT_MASK(32); > +static struct mci_platform_data mmc_data; > + > +static struct resource mmc_resources[] = { > + [0] = { > + .start = AT91RM9200_BASE_MCI, > + .end = AT91RM9200_BASE_MCI + SZ_16K - 1, > + .flags = IORESOURCE_MEM, > + }, > + [1] = { > + .start = AT91RM9200_ID_MCI, > + .end = AT91RM9200_ID_MCI, > + .flags = IORESOURCE_IRQ, > + }, > +}; > + > +static struct platform_device at91rm9200_mmc_device = { > + .name = "atmel_mci", > + .id = -1, > + .dev = { > + .dma_mask = &mmc_dmamask, > + .coherent_dma_mask = DMA_BIT_MASK(32), > + .platform_data = &mmc_data, > + }, > + .resource = mmc_resources, > + .num_resources = ARRAY_SIZE(mmc_resources), > +}; > + > +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) > +{ > + unsigned int i; > + unsigned int slot_count = 0; > + > + if (!data) > + return; > + > + for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) { > + > + if (!data->slot[i].bus_width) > + continue; > + > + /* input/irq */ > + if (gpio_is_valid(data->slot[i].detect_pin)) { > + at91_set_gpio_input(data->slot[i].detect_pin, 1); > + at91_set_deglitch(data->slot[i].detect_pin, 1); > + } > + if (gpio_is_valid(data->slot[i].wp_pin)) > + at91_set_gpio_input(data->slot[i].wp_pin, 1); > + > + switch (i) { > + case 0: /* slot A */ > + /* CMD */ > + at91_set_A_periph(AT91_PIN_PA28, 1); > + /* DAT0, maybe DAT1..DAT3 */ > + at91_set_A_periph(AT91_PIN_PA29, 1); > + if (data->slot[i].bus_width == 4) { > + at91_set_B_periph(AT91_PIN_PB3, 1); > + at91_set_B_periph(AT91_PIN_PB4, 1); > + at91_set_B_periph(AT91_PIN_PB5, 1); > + } > + slot_count++; > + break; > + case 1: /* slot B */ > + /* CMD */ > + at91_set_B_periph(AT91_PIN_PA8, 1); > + /* DAT0, maybe DAT1..DAT3 */ > + at91_set_B_periph(AT91_PIN_PA9, 1); > + if (data->slot[i].bus_width == 4) { > + at91_set_B_periph(AT91_PIN_PA10, 1); > + at91_set_B_periph(AT91_PIN_PA11, 1); > + at91_set_B_periph(AT91_PIN_PA12, 1); > + } > + slot_count++; > + break; > + default: > + printk(KERN_ERR > + "AT91: SD/MMC slot %d not available\n", i); > + break; > + } > + if (slot_count) { > + /* CLK */ > + at91_set_A_periph(AT91_PIN_PA27, 0); > + > + mmc_data = *data; > + platform_device_register(&at91rm9200_mmc_device); > + } > + } > + > +} > +#else > +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {} > +#endif > + > + > +/* -------------------------------------------------------------------- > * NAND / SmartMedia > * -------------------------------------------------------------------- */ > > diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c > index 4db961a..0817854 100644 > --- a/arch/arm/mach-at91/at91sam9261_devices.c > +++ b/arch/arm/mach-at91/at91sam9261_devices.c > @@ -202,7 +202,74 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) > void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {} > #endif > > +/* -------------------------------------------------------------------- > + * MMC / SD Slot for Atmel MCI Driver > + * -------------------------------------------------------------------- */ > + > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static u64 mmc_dmamask = DMA_BIT_MASK(32); > +static struct mci_platform_data mmc_data; > + > +static struct resource mmc_resources[] = { > + [0] = { > + .start = AT91SAM9261_BASE_MCI, > + .end = AT91SAM9261_BASE_MCI + SZ_16K - 1, > + .flags = IORESOURCE_MEM, > + }, > + [1] = { > + .start = AT91SAM9261_ID_MCI, > + .end = AT91SAM9261_ID_MCI, > + .flags = IORESOURCE_IRQ, > + }, > +}; > + > +static struct platform_device at91sam9261_mmc_device = { > + .name = "atmel_mci", > + .id = -1, > + .dev = { > + .dma_mask = &mmc_dmamask, > + .coherent_dma_mask = DMA_BIT_MASK(32), > + .platform_data = &mmc_data, > + }, > + .resource = mmc_resources, > + .num_resources = ARRAY_SIZE(mmc_resources), > +}; > + > +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) > +{ > + if (!data) > + return; > > + if (data->slot[0].bus_width) { > + /* input/irq */ > + if (gpio_is_valid(data->slot[0].detect_pin)) { > + at91_set_gpio_input(data->slot[0].detect_pin, 1); > + at91_set_deglitch(data->slot[0].detect_pin, 1); > + } > + if (gpio_is_valid(data->slot[0].wp_pin)) > + at91_set_gpio_input(data->slot[0].wp_pin, 1); > + > + /* CLK */ > + at91_set_B_periph(AT91_PIN_PA2, 0); > + > + /* CMD */ > + at91_set_B_periph(AT91_PIN_PA1, 1); > + > + /* DAT0, maybe DAT1..DAT3 */ > + at91_set_B_periph(AT91_PIN_PA0, 1); > + if (data->slot[0].bus_width == 4) { > + at91_set_B_periph(AT91_PIN_PA4, 1); > + at91_set_B_periph(AT91_PIN_PA5, 1); > + at91_set_B_periph(AT91_PIN_PA6, 1); > + } > + > + mmc_data = *data; > + platform_device_register(&at91sam9261_mmc_device); > + } > +} > +#else > +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {} > +#endif > /* -------------------------------------------------------------------- > * NAND / SmartMedia > * -------------------------------------------------------------------- */ > diff --git a/arch/arm/mach-at91/at91sam9263.c b/arch/arm/mach-at91/at91sam9263.c > index ef301be..053e47a 100644 > --- a/arch/arm/mach-at91/at91sam9263.c > +++ b/arch/arm/mach-at91/at91sam9263.c > @@ -189,6 +189,8 @@ static struct clk_lookup periph_clocks_lookups[] = { > CLKDEV_CON_DEV_ID("pclk", "ssc.1", &ssc1_clk), > CLKDEV_CON_DEV_ID("mci_clk", "at91_mci.0", &mmc0_clk), > CLKDEV_CON_DEV_ID("mci_clk", "at91_mci.1", &mmc1_clk), > + CLKDEV_CON_DEV_ID("mci_clk", "atmel_mci.0", &mmc0_clk), > + CLKDEV_CON_DEV_ID("mci_clk", "atmel_mci.1", &mmc1_clk), > CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.0", &spi0_clk), > CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.1", &spi1_clk), > CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tcb_clk), > diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c > index fe99206..617fbfc 100644 > --- a/arch/arm/mach-at91/at91sam9263_devices.c > +++ b/arch/arm/mach-at91/at91sam9263_devices.c > @@ -354,6 +354,170 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {} > #endif > > /* -------------------------------------------------------------------- > + * MMC / SD > + * -------------------------------------------------------------------- */ > + > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static u64 mmc_dmamask = DMA_BIT_MASK(32); > +static struct mci_platform_data mmc0_data, mmc1_data; > + > +static struct resource mmc0_resources[] = { > + [0] = { > + .start = AT91SAM9263_BASE_MCI0, > + .end = AT91SAM9263_BASE_MCI0 + SZ_16K - 1, > + .flags = IORESOURCE_MEM, > + }, > + [1] = { > + .start = AT91SAM9263_ID_MCI0, > + .end = AT91SAM9263_ID_MCI0, > + .flags = IORESOURCE_IRQ, > + }, > +}; > + > +static struct platform_device at91sam9263_mmc0_device = { > + .name = "atmel_mci", > + .id = 0, > + .dev = { > + .dma_mask = &mmc_dmamask, > + .coherent_dma_mask = DMA_BIT_MASK(32), > + .platform_data = &mmc0_data, > + }, > + .resource = mmc0_resources, > + .num_resources = ARRAY_SIZE(mmc0_resources), > +}; > + > +static struct resource mmc1_resources[] = { > + [0] = { > + .start = AT91SAM9263_BASE_MCI1, > + .end = AT91SAM9263_BASE_MCI1 + SZ_16K - 1, > + .flags = IORESOURCE_MEM, > + }, > + [1] = { > + .start = AT91SAM9263_ID_MCI1, > + .end = AT91SAM9263_ID_MCI1, > + .flags = IORESOURCE_IRQ, > + }, > +}; > + > +static struct platform_device at91sam9263_mmc1_device = { > + .name = "atmel_mci", > + .id = 1, > + .dev = { > + .dma_mask = &mmc_dmamask, > + .coherent_dma_mask = DMA_BIT_MASK(32), > + .platform_data = &mmc1_data, > + }, > + .resource = mmc1_resources, > + .num_resources = ARRAY_SIZE(mmc1_resources), > +}; > + > +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) > +{ > + unsigned int i; > + unsigned int slot_count = 0; > + > + if (!data) > + return; > + > + for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) { > + > + if (!data->slot[i].bus_width) > + continue; > + > + /* input/irq */ > + if (gpio_is_valid(data->slot[i].detect_pin)) { > + at91_set_gpio_input(data->slot[i].detect_pin, > + 1); > + at91_set_deglitch(data->slot[i].detect_pin, > + 1); > + } > + if (gpio_is_valid(data->slot[i].wp_pin)) > + at91_set_gpio_input(data->slot[i].wp_pin, 1); > + > + if (mmc_id == 0) { /* MCI0 */ > + switch (i) { > + case 0: /* slot A */ > + /* CMD */ > + at91_set_A_periph(AT91_PIN_PA1, 1); > + /* DAT0, maybe DAT1..DAT3 */ > + at91_set_A_periph(AT91_PIN_PA0, 1); > + if (data->slot[i].bus_width == 4) { > + at91_set_A_periph(AT91_PIN_PA3, 1); > + at91_set_A_periph(AT91_PIN_PA4, 1); > + at91_set_A_periph(AT91_PIN_PA5, 1); > + } > + slot_count++; > + break; > + case 1: /* slot B */ > + /* CMD */ > + at91_set_A_periph(AT91_PIN_PA16, 1); > + /* DAT0, maybe DAT1..DAT3 */ > + at91_set_A_periph(AT91_PIN_PA17, 1); > + if (data->slot[i].bus_width == 4) { > + at91_set_A_periph(AT91_PIN_PA18, 1); > + at91_set_A_periph(AT91_PIN_PA19, 1); > + at91_set_A_periph(AT91_PIN_PA20, 1); > + } > + slot_count++; > + break; > + default: > + printk(KERN_ERR > + "AT91: SD/MMC slot %d not available\n", i); > + break; > + } > + if (slot_count) { > + /* CLK */ > + at91_set_A_periph(AT91_PIN_PA12, 0); > + > + mmc0_data = *data; > + platform_device_register(&at91sam9263_mmc0_device); > + } > + } else if (mmc_id == 1) { /* MCI1 */ > + switch (i) { > + case 0: /* slot A */ > + /* CMD */ > + at91_set_A_periph(AT91_PIN_PA7, 1); > + /* DAT0, maybe DAT1..DAT3 */ > + at91_set_A_periph(AT91_PIN_PA8, 1); > + if (data->slot[i].bus_width == 4) { > + at91_set_A_periph(AT91_PIN_PA9, 1); > + at91_set_A_periph(AT91_PIN_PA10, 1); > + at91_set_A_periph(AT91_PIN_PA11, 1); > + } > + slot_count++; > + break; > + case 1: /* slot B */ > + /* CMD */ > + at91_set_A_periph(AT91_PIN_PA21, 1); > + /* DAT0, maybe DAT1..DAT3 */ > + at91_set_A_periph(AT91_PIN_PA22, 1); > + if (data->slot[i].bus_width == 4) { > + at91_set_A_periph(AT91_PIN_PA23, 1); > + at91_set_A_periph(AT91_PIN_PA24, 1); > + at91_set_A_periph(AT91_PIN_PA25, 1); > + } > + slot_count++; > + break; > + default: > + printk(KERN_ERR > + "AT91: SD/MMC slot %d not available\n", i); > + break; > + } > + if (slot_count) { > + /* CLK */ > + at91_set_A_periph(AT91_PIN_PA6, 0); > + > + mmc1_data = *data; > + platform_device_register(&at91sam9263_mmc1_device); > + } > + } > + } > +} > +#else > +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {} > +#endif > + > +/* -------------------------------------------------------------------- > * Compact Flash (PCMCIA or IDE) > * -------------------------------------------------------------------- */ > > diff --git a/arch/arm/mach-at91/at91sam9rl_devices.c b/arch/arm/mach-at91/at91sam9rl_devices.c > index fe4ae22..83c5845 100644 > --- a/arch/arm/mach-at91/at91sam9rl_devices.c > +++ b/arch/arm/mach-at91/at91sam9rl_devices.c > @@ -228,6 +228,76 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {} > > > /* -------------------------------------------------------------------- > + * MMC / SD > + * -------------------------------------------------------------------- */ > + > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static u64 mmc_dmamask = DMA_BIT_MASK(32); > +static struct mci_platform_data mmc_data; > + > +static struct resource mmc_resources[] = { > + [0] = { > + .start = AT91SAM9RL_BASE_MCI, > + .end = AT91SAM9RL_BASE_MCI + SZ_16K - 1, > + .flags = IORESOURCE_MEM, > + }, > + [1] = { > + .start = AT91SAM9RL_ID_MCI, > + .end = AT91SAM9RL_ID_MCI, > + .flags = IORESOURCE_IRQ, > + }, > +}; > + > +static struct platform_device at91sam9rl_mmc_device = { > + .name = "atmel_mci", > + .id = -1, > + .dev = { > + .dma_mask = &mmc_dmamask, > + .coherent_dma_mask = DMA_BIT_MASK(32), > + .platform_data = &mmc_data, > + }, > + .resource = mmc_resources, > + .num_resources = ARRAY_SIZE(mmc_resources), > +}; > + > +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) > +{ > + if (!data) > + return; > + > + if (data->slot[0].bus_width) { > + /* input/irq */ > + if (gpio_is_valid(data->slot[0].detect_pin)) { > + at91_set_gpio_input(data->slot[0].detect_pin, 1); > + at91_set_deglitch(data->slot[0].detect_pin, 1); > + } > + if (gpio_is_valid(data->slot[0].wp_pin)) > + at91_set_gpio_input(data->slot[0].wp_pin, 1); > + > + /* CLK */ > + at91_set_A_periph(AT91_PIN_PA2, 0); > + > + /* CMD */ > + at91_set_A_periph(AT91_PIN_PA1, 1); > + > + /* DAT0, maybe DAT1..DAT3 */ > + at91_set_A_periph(AT91_PIN_PA0, 1); > + if (data->slot[0].bus_width == 4) { > + at91_set_A_periph(AT91_PIN_PA3, 1); > + at91_set_A_periph(AT91_PIN_PA4, 1); > + at91_set_A_periph(AT91_PIN_PA5, 1); > + } > + > + mmc_data = *data; > + platform_device_register(&at91sam9rl_mmc_device); > + } > +} > +#else > +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {} > +#endif > + > + > +/* -------------------------------------------------------------------- > * NAND / SmartMedia > * -------------------------------------------------------------------- */ > > diff --git a/arch/arm/mach-at91/board-foxg20.c b/arch/arm/mach-at91/board-foxg20.c > index caf017f..6cda303 100644 > --- a/arch/arm/mach-at91/board-foxg20.c > +++ b/arch/arm/mach-at91/board-foxg20.c > @@ -123,7 +123,7 @@ static struct at91_udc_data __initdata foxg20_udc_data = { > * SPI devices. > */ > static struct spi_board_info foxg20_spi_devices[] = { > -#if !defined(CONFIG_MMC_AT91) > +#if !defined(CONFIG_MMC_AT91) && !defined(CONFIG_MMC_ATMELMCI) > { > .modalias = "mtd_dataflash", > .chip_select = 1, > @@ -146,6 +146,7 @@ static struct macb_platform_data __initdata foxg20_macb_data = { > * MCI (SD/MMC) > * det_pin, wp_pin and vcc_pin are not connected > */ > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > static struct at91_mmc_data __initdata foxg20_mmc_data = { > .slot_b = 1, > .wire4 = 1, > @@ -153,6 +154,15 @@ static struct at91_mmc_data __initdata foxg20_mmc_data = { > .wp_pin = -EINVAL, > .vcc_pin = -EINVAL, > }; > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata foxg20_mci0_data = { > + .slot[1] = { > + .bus_width = 4, > + .detect_pin = -EINVAL, > + .wp_pin = -EINVAL, > + }, > +}; > +#endif > > > /* > @@ -251,7 +261,11 @@ static void __init foxg20_board_init(void) > /* Ethernet */ > at91_add_device_eth(&foxg20_macb_data); > /* MMC */ > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > at91_add_device_mmc(0, &foxg20_mmc_data); > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0, &foxg20_mci0_data); > +#endif > /* I2C */ > at91_add_device_i2c(foxg20_i2c_devices, ARRAY_SIZE(foxg20_i2c_devices)); > /* LEDs */ > diff --git a/arch/arm/mach-at91/board-rm9200ek.c b/arch/arm/mach-at91/board-rm9200ek.c > index b2e4fe2..7177aac 100644 > --- a/arch/arm/mach-at91/board-rm9200ek.c > +++ b/arch/arm/mach-at91/board-rm9200ek.c > @@ -83,6 +83,7 @@ static struct at91_udc_data __initdata ek_udc_data = { > }; > > #ifndef CONFIG_MTD_AT91_DATAFLASH_CARD > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > static struct at91_mmc_data __initdata ek_mmc_data = { > .det_pin = AT91_PIN_PB27, > .slot_b = 0, > @@ -90,6 +91,15 @@ static struct at91_mmc_data __initdata ek_mmc_data = { > .wp_pin = AT91_PIN_PA17, > .vcc_pin = -EINVAL, > }; > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata ek_mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PB27, > + .wp_pin = AT91_PIN_PA17, > + } > +}; > +#endif > #endif > > static struct spi_board_info ek_spi_devices[] = { > @@ -180,7 +190,11 @@ static void __init ek_board_init(void) > #else > /* MMC */ > at91_set_gpio_output(AT91_PIN_PB22, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */ > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > at91_add_device_mmc(0, &ek_mmc_data); > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0, &ek_mci0_data); > +#endif > #endif > /* NOR Flash */ > platform_device_register(&ek_flash); > diff --git a/arch/arm/mach-at91/board-sam9-l9260.c b/arch/arm/mach-at91/board-sam9-l9260.c > index e8b116b..4a5786b 100644 > --- a/arch/arm/mach-at91/board-sam9-l9260.c > +++ b/arch/arm/mach-at91/board-sam9-l9260.c > @@ -89,7 +89,7 @@ static struct at91_udc_data __initdata ek_udc_data = { > * SPI devices. > */ > static struct spi_board_info ek_spi_devices[] = { > -#if !defined(CONFIG_MMC_AT91) > +#if !defined(CONFIG_MMC_AT91) && !defined(CONFIG_MMC_ATMELMCI) > { /* DataFlash chip */ > .modalias = "mtd_dataflash", > .chip_select = 1, > @@ -174,6 +174,7 @@ static void __init ek_add_device_nand(void) > /* > * MCI (SD/MMC) > */ > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > static struct at91_mmc_data __initdata ek_mmc_data = { > .slot_b = 1, > .wire4 = 1, > @@ -181,6 +182,15 @@ static struct at91_mmc_data __initdata ek_mmc_data = { > .wp_pin = AT91_PIN_PC4, > .vcc_pin = -EINVAL, > }; > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata mci0_data = { > + .slot[1] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PC8, > + .wp_pin = AT91_PIN_PC4, > + }, > +}; > +#endif > > static void __init ek_board_init(void) > { > @@ -197,7 +207,11 @@ static void __init ek_board_init(void) > /* Ethernet */ > at91_add_device_eth(&ek_macb_data); > /* MMC */ > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > at91_add_device_mmc(0, &ek_mmc_data); > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0, &ek_mci0_data); > +#endif > /* I2C */ > at91_add_device_i2c(NULL, 0); > } > diff --git a/arch/arm/mach-at91/board-sam9260ek.c b/arch/arm/mach-at91/board-sam9260ek.c > index d5aec55..b6ce2df 100644 > --- a/arch/arm/mach-at91/board-sam9260ek.c > +++ b/arch/arm/mach-at91/board-sam9260ek.c > @@ -121,7 +121,7 @@ static void __init at73c213_set_clk(struct at73c213_board_info *info) {} > * SPI devices. > */ > static struct spi_board_info ek_spi_devices[] = { > -#if !defined(CONFIG_MMC_AT91) > +#if !defined(CONFIG_MMC_AT91) && !defined(CONFIG_MMC_ATMELMCI) > { /* DataFlash chip */ > .modalias = "mtd_dataflash", > .chip_select = 1, > @@ -224,6 +224,7 @@ static void __init ek_add_device_nand(void) > /* > * MCI (SD/MMC) > */ > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > static struct at91_mmc_data __initdata ek_mmc_data = { > .slot_b = 1, > .wire4 = 1, > @@ -231,6 +232,15 @@ static struct at91_mmc_data __initdata ek_mmc_data = { > .wp_pin = -EINVAL, > .vcc_pin = -EINVAL, > }; > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata mci0_data = { > + .slot[1] = { > + .bus_width = 4, > + .detect_pin = -EINVAL, > + .wp_pin = -EINVAL, > + }, > +}; > +#endif > > > /* > @@ -332,7 +342,11 @@ static void __init ek_board_init(void) > /* Ethernet */ > at91_add_device_eth(&ek_macb_data); > /* MMC */ > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > at91_add_device_mmc(0, &ek_mmc_data); > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0, &ek_mci0_data); > +#endif > /* I2C */ > at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices)); > /* SSC (to AT73C213) */ > diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c > index 065fed3..797dd7c 100644 > --- a/arch/arm/mach-at91/board-sam9261ek.c > +++ b/arch/arm/mach-at91/board-sam9261ek.c > @@ -344,6 +344,7 @@ static struct spi_board_info ek_spi_devices[] = { > #else /* CONFIG_SPI_ATMEL_* */ > /* spi0 and mmc/sd share the same PIO pins: cannot be used at the same time */ > > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > /* > * MCI (SD/MMC) > * det_pin, wp_pin and vcc_pin are not connected > @@ -354,6 +355,15 @@ static struct at91_mmc_data __initdata ek_mmc_data = { > .wp_pin = -EINVAL, > .vcc_pin = -EINVAL, > }; > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = -EINVAL, > + .wp_pin = -EINVAL, > + }, > +}; > +#endif > > #endif /* CONFIG_SPI_ATMEL_* */ > > @@ -601,7 +611,11 @@ static void __init ek_board_init(void) > at91_add_device_ssc(AT91SAM9261_ID_SSC1, ATMEL_SSC_TX); > #else > /* MMC */ > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > at91_add_device_mmc(0, &ek_mmc_data); > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0, &mci0_data); > +#endif > #endif > /* LCD Controller */ > at91_add_device_lcdc(&ek_lcdc_data); > diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c > index 2ffe50f..8080d02 100644 > --- a/arch/arm/mach-at91/board-sam9263ek.c > +++ b/arch/arm/mach-at91/board-sam9263ek.c > @@ -149,12 +149,22 @@ static struct spi_board_info ek_spi_devices[] = { > /* > * MCI (SD/MMC) > */ > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > static struct at91_mmc_data __initdata ek_mmc_data = { > .wire4 = 1, > .det_pin = AT91_PIN_PE18, > .wp_pin = AT91_PIN_PE19, > .vcc_pin = -EINVAL, > }; > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata mci1_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PE18, > + .wp_pin = AT91_PIN_PE19, > + }, > +}; > +#endif > > > /* > @@ -423,7 +433,11 @@ static void __init ek_board_init(void) > /* Touchscreen */ > ek_add_device_ts(); > /* MMC */ > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > at91_add_device_mmc(1, &ek_mmc_data); > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(1, &mci1_data); > +#endif > /* Ethernet */ > at91_add_device_eth(&ek_macb_data); > /* NAND */ > diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c > index b109ce2..bb06521 100644 > --- a/arch/arm/mach-at91/board-sam9rlek.c > +++ b/arch/arm/mach-at91/board-sam9rlek.c > @@ -64,12 +64,22 @@ static struct usba_platform_data __initdata ek_usba_udc_data = { > /* > * MCI (SD/MMC) > */ > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > static struct at91_mmc_data __initdata ek_mmc_data = { > .wire4 = 1, > .det_pin = AT91_PIN_PA15, > .wp_pin = -EINVAL, > .vcc_pin = -EINVAL, > }; > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PA15, > + .wp_pin = -EINVAL, > + }, > +}; > +#endif > > > /* > @@ -306,7 +316,11 @@ static void __init ek_board_init(void) > /* SPI */ > at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); > /* MMC */ > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > at91_add_device_mmc(0, &ek_mmc_data); > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0, &mci0_data); > +#endif > /* LCD Controller */ > at91_add_device_lcdc(&ek_lcdc_data); > /* AC97 */ > diff --git a/arch/arm/mach-at91/board-usb-a926x.c b/arch/arm/mach-at91/board-usb-a926x.c > index b7483a3..879e34e 100644 > --- a/arch/arm/mach-at91/board-usb-a926x.c > +++ b/arch/arm/mach-at91/board-usb-a926x.c > @@ -114,7 +114,7 @@ static struct mmc_spi_platform_data at91_mmc_spi_pdata = { > * SPI devices. > */ > static struct spi_board_info usb_a9263_spi_devices[] = { > -#if !defined(CONFIG_MMC_AT91) > +#if !defined(CONFIG_MMC_AT91) && !defined(CONFIG_MMC_ATMELMCI) > { /* DataFlash chip */ > .modalias = "mtd_dataflash", > .chip_select = 0, -- Nicolas Ferre ^ permalink raw reply [flat|nested] 28+ messages in thread
* [PATCH 2/2] mmc: at91-mci: this driver is now deprecated 2012-05-16 15:51 ` ludovic.desroches at atmel.com @ 2012-05-16 15:51 ` ludovic.desroches at atmel.com -1 siblings, 0 replies; 28+ messages in thread From: ludovic.desroches @ 2012-05-16 15:51 UTC (permalink / raw) To: linux-mmc, linux-arm-kernel; +Cc: nicolas.ferre, plagnioj, Ludovic Desroches From: Ludovic Desroches <ludovic.desroches@atmel.com> at91-mci is deprecated since atmel-mci can deal with all chips. Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> --- Documentation/feature-removal-schedule.txt | 11 +++++++++++ drivers/mmc/host/Kconfig | 7 +++++-- 2 files changed, 16 insertions(+), 2 deletions(-) diff --git a/Documentation/feature-removal-schedule.txt b/Documentation/feature-removal-schedule.txt index 03ca210..8b4aef2 100644 --- a/Documentation/feature-removal-schedule.txt +++ b/Documentation/feature-removal-schedule.txt @@ -539,3 +539,14 @@ When: 3.6 Why: setitimer is not returning -EFAULT if user pointer is NULL. This violates the spec. Who: Sasikantha Babu <sasikanth.v19@gmail.com> + +---------------------------- + +What: at91-mci driver ("CONFIG_MMC_AT91") +When: 3.7 +Why: There two mci drivers: at91-mci and atmel-mci. The PDC support was + added to atmel-mci as a first step to support more chips. Then + at91-mci was kept only for old IP versions (on at91rm9200 and + at91sam9261). The support of these IP versions has just been added + so atmel-mci can be used for all chips. +Who: Ludovic Desroches <ludovic.desroches@atmel.com> diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig index 2bc06e7..f150591 100644 --- a/drivers/mmc/host/Kconfig +++ b/drivers/mmc/host/Kconfig @@ -278,10 +278,13 @@ choice Choose which driver to use for the Atmel MCI Silicon config MMC_AT91 - tristate "AT91 SD/MMC Card Interface support" + tristate "AT91 SD/MMC Card Interface support (DEPRECATED)" depends on ARCH_AT91 help - This selects the AT91 MCI controller. + This selects the AT91 MCI controller. This driver will be + remove soon (for more information have a look to + Documentation/feature-removal-schedule.txt). Please use + MMC_ATMEL_MCI. If unsure, say N. -- 1.7.5.4 ^ permalink raw reply related [flat|nested] 28+ messages in thread
* [PATCH 2/2] mmc: at91-mci: this driver is now deprecated @ 2012-05-16 15:51 ` ludovic.desroches at atmel.com 0 siblings, 0 replies; 28+ messages in thread From: ludovic.desroches at atmel.com @ 2012-05-16 15:51 UTC (permalink / raw) To: linux-arm-kernel From: Ludovic Desroches <ludovic.desroches@atmel.com> at91-mci is deprecated since atmel-mci can deal with all chips. Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> --- Documentation/feature-removal-schedule.txt | 11 +++++++++++ drivers/mmc/host/Kconfig | 7 +++++-- 2 files changed, 16 insertions(+), 2 deletions(-) diff --git a/Documentation/feature-removal-schedule.txt b/Documentation/feature-removal-schedule.txt index 03ca210..8b4aef2 100644 --- a/Documentation/feature-removal-schedule.txt +++ b/Documentation/feature-removal-schedule.txt @@ -539,3 +539,14 @@ When: 3.6 Why: setitimer is not returning -EFAULT if user pointer is NULL. This violates the spec. Who: Sasikantha Babu <sasikanth.v19@gmail.com> + +---------------------------- + +What: at91-mci driver ("CONFIG_MMC_AT91") +When: 3.7 +Why: There two mci drivers: at91-mci and atmel-mci. The PDC support was + added to atmel-mci as a first step to support more chips. Then + at91-mci was kept only for old IP versions (on at91rm9200 and + at91sam9261). The support of these IP versions has just been added + so atmel-mci can be used for all chips. +Who: Ludovic Desroches <ludovic.desroches@atmel.com> diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig index 2bc06e7..f150591 100644 --- a/drivers/mmc/host/Kconfig +++ b/drivers/mmc/host/Kconfig @@ -278,10 +278,13 @@ choice Choose which driver to use for the Atmel MCI Silicon config MMC_AT91 - tristate "AT91 SD/MMC Card Interface support" + tristate "AT91 SD/MMC Card Interface support (DEPRECATED)" depends on ARCH_AT91 help - This selects the AT91 MCI controller. + This selects the AT91 MCI controller. This driver will be + remove soon (for more information have a look to + Documentation/feature-removal-schedule.txt). Please use + MMC_ATMEL_MCI. If unsure, say N. -- 1.7.5.4 ^ permalink raw reply related [flat|nested] 28+ messages in thread
* Re: [PATCH 2/2] mmc: at91-mci: this driver is now deprecated 2012-05-16 15:51 ` ludovic.desroches at atmel.com @ 2012-05-17 12:45 ` Chris Ball -1 siblings, 0 replies; 28+ messages in thread From: Chris Ball @ 2012-05-17 12:45 UTC (permalink / raw) To: ludovic.desroches; +Cc: linux-mmc, linux-arm-kernel, nicolas.ferre, plagnioj Hi, On Wed, May 16 2012, ludovic.desroches@atmel.com wrote: > From: Ludovic Desroches <ludovic.desroches@atmel.com> > > at91-mci is deprecated since atmel-mci can deal with all chips. > > Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> > --- > Documentation/feature-removal-schedule.txt | 11 +++++++++++ > drivers/mmc/host/Kconfig | 7 +++++-- > 2 files changed, 16 insertions(+), 2 deletions(-) > > diff --git a/Documentation/feature-removal-schedule.txt b/Documentation/feature-removal-schedule.txt > index 03ca210..8b4aef2 100644 > --- a/Documentation/feature-removal-schedule.txt > +++ b/Documentation/feature-removal-schedule.txt > @@ -539,3 +539,14 @@ When: 3.6 > Why: setitimer is not returning -EFAULT if user pointer is NULL. This > violates the spec. > Who: Sasikantha Babu <sasikanth.v19@gmail.com> > + > +---------------------------- > + > +What: at91-mci driver ("CONFIG_MMC_AT91") > +When: 3.7 > +Why: There two mci drivers: at91-mci and atmel-mci. The PDC support was ^ are > + added to atmel-mci as a first step to support more chips. Then > + at91-mci was kept only for old IP versions (on at91rm9200 and > + at91sam9261). The support of these IP versions has just been added > + so atmel-mci can be used for all chips. > +Who: Ludovic Desroches <ludovic.desroches@atmel.com> > diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig > index 2bc06e7..f150591 100644 > --- a/drivers/mmc/host/Kconfig > +++ b/drivers/mmc/host/Kconfig > @@ -278,10 +278,13 @@ choice > Choose which driver to use for the Atmel MCI Silicon > > config MMC_AT91 > - tristate "AT91 SD/MMC Card Interface support" > + tristate "AT91 SD/MMC Card Interface support (DEPRECATED)" > depends on ARCH_AT91 > help > - This selects the AT91 MCI controller. > + This selects the AT91 MCI controller. This driver will be > + remove soon (for more information have a look to ^ removed > + Documentation/feature-removal-schedule.txt). Please use > + MMC_ATMEL_MCI. > > If unsure, say N. Seems like I should take this patch 2/2, and then someone else should merge 1/2? Thanks, - Chris. -- Chris Ball <cjb@laptop.org> <http://printf.net/> One Laptop Per Child ^ permalink raw reply [flat|nested] 28+ messages in thread
* [PATCH 2/2] mmc: at91-mci: this driver is now deprecated @ 2012-05-17 12:45 ` Chris Ball 0 siblings, 0 replies; 28+ messages in thread From: Chris Ball @ 2012-05-17 12:45 UTC (permalink / raw) To: linux-arm-kernel Hi, On Wed, May 16 2012, ludovic.desroches at atmel.com wrote: > From: Ludovic Desroches <ludovic.desroches@atmel.com> > > at91-mci is deprecated since atmel-mci can deal with all chips. > > Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> > --- > Documentation/feature-removal-schedule.txt | 11 +++++++++++ > drivers/mmc/host/Kconfig | 7 +++++-- > 2 files changed, 16 insertions(+), 2 deletions(-) > > diff --git a/Documentation/feature-removal-schedule.txt b/Documentation/feature-removal-schedule.txt > index 03ca210..8b4aef2 100644 > --- a/Documentation/feature-removal-schedule.txt > +++ b/Documentation/feature-removal-schedule.txt > @@ -539,3 +539,14 @@ When: 3.6 > Why: setitimer is not returning -EFAULT if user pointer is NULL. This > violates the spec. > Who: Sasikantha Babu <sasikanth.v19@gmail.com> > + > +---------------------------- > + > +What: at91-mci driver ("CONFIG_MMC_AT91") > +When: 3.7 > +Why: There two mci drivers: at91-mci and atmel-mci. The PDC support was ^ are > + added to atmel-mci as a first step to support more chips. Then > + at91-mci was kept only for old IP versions (on at91rm9200 and > + at91sam9261). The support of these IP versions has just been added > + so atmel-mci can be used for all chips. > +Who: Ludovic Desroches <ludovic.desroches@atmel.com> > diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig > index 2bc06e7..f150591 100644 > --- a/drivers/mmc/host/Kconfig > +++ b/drivers/mmc/host/Kconfig > @@ -278,10 +278,13 @@ choice > Choose which driver to use for the Atmel MCI Silicon > > config MMC_AT91 > - tristate "AT91 SD/MMC Card Interface support" > + tristate "AT91 SD/MMC Card Interface support (DEPRECATED)" > depends on ARCH_AT91 > help > - This selects the AT91 MCI controller. > + This selects the AT91 MCI controller. This driver will be > + remove soon (for more information have a look to ^ removed > + Documentation/feature-removal-schedule.txt). Please use > + MMC_ATMEL_MCI. > > If unsure, say N. Seems like I should take this patch 2/2, and then someone else should merge 1/2? Thanks, - Chris. -- Chris Ball <cjb@laptop.org> <http://printf.net/> One Laptop Per Child ^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: [PATCH 2/2] mmc: at91-mci: this driver is now deprecated 2012-05-17 12:45 ` Chris Ball @ 2012-05-17 18:28 ` ludovic.desroches -1 siblings, 0 replies; 28+ messages in thread From: ludovic.desroches @ 2012-05-17 18:28 UTC (permalink / raw) To: Chris Ball Cc: nicolas.ferre, plagnioj, ludovic.desroches, linux-mmc, linux-arm-kernel Hi Chris, Le 05/17/2012 02:45 PM, Chris Ball a écrit : > Hi, > > On Wed, May 16 2012, ludovic.desroches@atmel.com wrote: >> From: Ludovic Desroches<ludovic.desroches@atmel.com> >> >> at91-mci is deprecated since atmel-mci can deal with all chips. >> >> Signed-off-by: Ludovic Desroches<ludovic.desroches@atmel.com> >> --- >> Documentation/feature-removal-schedule.txt | 11 +++++++++++ >> drivers/mmc/host/Kconfig | 7 +++++-- >> 2 files changed, 16 insertions(+), 2 deletions(-) >> >> diff --git a/Documentation/feature-removal-schedule.txt b/Documentation/feature-removal-schedule.txt >> index 03ca210..8b4aef2 100644 >> --- a/Documentation/feature-removal-schedule.txt >> +++ b/Documentation/feature-removal-schedule.txt >> @@ -539,3 +539,14 @@ When: 3.6 >> Why: setitimer is not returning -EFAULT if user pointer is NULL. This >> violates the spec. >> Who: Sasikantha Babu<sasikanth.v19@gmail.com> >> + >> +---------------------------- >> + >> +What: at91-mci driver ("CONFIG_MMC_AT91") >> +When: 3.7 >> +Why: There two mci drivers: at91-mci and atmel-mci. The PDC support was > ^ are > >> + added to atmel-mci as a first step to support more chips. Then >> + at91-mci was kept only for old IP versions (on at91rm9200 and >> + at91sam9261). The support of these IP versions has just been added >> + so atmel-mci can be used for all chips. >> +Who: Ludovic Desroches<ludovic.desroches@atmel.com> >> diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig >> index 2bc06e7..f150591 100644 >> --- a/drivers/mmc/host/Kconfig >> +++ b/drivers/mmc/host/Kconfig >> @@ -278,10 +278,13 @@ choice >> Choose which driver to use for the Atmel MCI Silicon >> >> config MMC_AT91 >> - tristate "AT91 SD/MMC Card Interface support" >> + tristate "AT91 SD/MMC Card Interface support (DEPRECATED)" >> depends on ARCH_AT91 >> help >> - This selects the AT91 MCI controller. >> + This selects the AT91 MCI controller. This driver will be >> + remove soon (for more information have a look to > ^ removed >> + Documentation/feature-removal-schedule.txt). Please use >> + MMC_ATMEL_MCI. >> >> If unsure, say N. Sorry for the typo, do you want a new patch or is ok? > > Seems like I should take this patch 2/2, and then someone else should > merge 1/2? Yes, Nicolas would probably take patch 2/2. Regards Ludovic ^ permalink raw reply [flat|nested] 28+ messages in thread
* [PATCH 2/2] mmc: at91-mci: this driver is now deprecated @ 2012-05-17 18:28 ` ludovic.desroches 0 siblings, 0 replies; 28+ messages in thread From: ludovic.desroches @ 2012-05-17 18:28 UTC (permalink / raw) To: linux-arm-kernel Hi Chris, Le 05/17/2012 02:45 PM, Chris Ball a ?crit : > Hi, > > On Wed, May 16 2012, ludovic.desroches at atmel.com wrote: >> From: Ludovic Desroches<ludovic.desroches@atmel.com> >> >> at91-mci is deprecated since atmel-mci can deal with all chips. >> >> Signed-off-by: Ludovic Desroches<ludovic.desroches@atmel.com> >> --- >> Documentation/feature-removal-schedule.txt | 11 +++++++++++ >> drivers/mmc/host/Kconfig | 7 +++++-- >> 2 files changed, 16 insertions(+), 2 deletions(-) >> >> diff --git a/Documentation/feature-removal-schedule.txt b/Documentation/feature-removal-schedule.txt >> index 03ca210..8b4aef2 100644 >> --- a/Documentation/feature-removal-schedule.txt >> +++ b/Documentation/feature-removal-schedule.txt >> @@ -539,3 +539,14 @@ When: 3.6 >> Why: setitimer is not returning -EFAULT if user pointer is NULL. This >> violates the spec. >> Who: Sasikantha Babu<sasikanth.v19@gmail.com> >> + >> +---------------------------- >> + >> +What: at91-mci driver ("CONFIG_MMC_AT91") >> +When: 3.7 >> +Why: There two mci drivers: at91-mci and atmel-mci. The PDC support was > ^ are > >> + added to atmel-mci as a first step to support more chips. Then >> + at91-mci was kept only for old IP versions (on at91rm9200 and >> + at91sam9261). The support of these IP versions has just been added >> + so atmel-mci can be used for all chips. >> +Who: Ludovic Desroches<ludovic.desroches@atmel.com> >> diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig >> index 2bc06e7..f150591 100644 >> --- a/drivers/mmc/host/Kconfig >> +++ b/drivers/mmc/host/Kconfig >> @@ -278,10 +278,13 @@ choice >> Choose which driver to use for the Atmel MCI Silicon >> >> config MMC_AT91 >> - tristate "AT91 SD/MMC Card Interface support" >> + tristate "AT91 SD/MMC Card Interface support (DEPRECATED)" >> depends on ARCH_AT91 >> help >> - This selects the AT91 MCI controller. >> + This selects the AT91 MCI controller. This driver will be >> + remove soon (for more information have a look to > ^ removed >> + Documentation/feature-removal-schedule.txt). Please use >> + MMC_ATMEL_MCI. >> >> If unsure, say N. Sorry for the typo, do you want a new patch or is ok? > > Seems like I should take this patch 2/2, and then someone else should > merge 1/2? Yes, Nicolas would probably take patch 2/2. Regards Ludovic ^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: [PATCH 2/2] mmc: at91-mci: this driver is now deprecated 2012-05-17 18:28 ` ludovic.desroches @ 2012-05-17 18:36 ` Chris Ball -1 siblings, 0 replies; 28+ messages in thread From: Chris Ball @ 2012-05-17 18:36 UTC (permalink / raw) To: ludovic.desroches; +Cc: plagnioj, linux-mmc, nicolas.ferre, linux-arm-kernel Hi, On Thu, May 17 2012, ludovic.desroches wrote: >>> + remove soon (for more information have a look to >> ^ removed >>> + Documentation/feature-removal-schedule.txt). Please use >>> + MMC_ATMEL_MCI. >>> >>> If unsure, say N. > > Sorry for the typo, do you want a new patch or is ok? It's okay, I've fixed it up here. >> Seems like I should take this patch 2/2, and then someone else should >> merge 1/2? > > Yes, Nicolas would probably take patch 2/2. I think you must mean that Nicolas takes 1/2 (the arch/arm/ patches). Assuming you do, that's fine and I've pushed 2/2 to mmc-next for 3.5 now. Thanks, - Chris. -- Chris Ball <cjb@laptop.org> <http://printf.net/> One Laptop Per Child ^ permalink raw reply [flat|nested] 28+ messages in thread
* [PATCH 2/2] mmc: at91-mci: this driver is now deprecated @ 2012-05-17 18:36 ` Chris Ball 0 siblings, 0 replies; 28+ messages in thread From: Chris Ball @ 2012-05-17 18:36 UTC (permalink / raw) To: linux-arm-kernel Hi, On Thu, May 17 2012, ludovic.desroches wrote: >>> + remove soon (for more information have a look to >> ^ removed >>> + Documentation/feature-removal-schedule.txt). Please use >>> + MMC_ATMEL_MCI. >>> >>> If unsure, say N. > > Sorry for the typo, do you want a new patch or is ok? It's okay, I've fixed it up here. >> Seems like I should take this patch 2/2, and then someone else should >> merge 1/2? > > Yes, Nicolas would probably take patch 2/2. I think you must mean that Nicolas takes 1/2 (the arch/arm/ patches). Assuming you do, that's fine and I've pushed 2/2 to mmc-next for 3.5 now. Thanks, - Chris. -- Chris Ball <cjb@laptop.org> <http://printf.net/> One Laptop Per Child ^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: [PATCH 2/2] mmc: at91-mci: this driver is now deprecated 2012-05-17 18:36 ` Chris Ball @ 2012-05-17 18:40 ` ludovic.desroches -1 siblings, 0 replies; 28+ messages in thread From: ludovic.desroches @ 2012-05-17 18:40 UTC (permalink / raw) To: Chris Ball Cc: plagnioj, linux-mmc, ludovic.desroches, nicolas.ferre, linux-arm-kernel Le 05/17/2012 08:36 PM, Chris Ball a écrit : > Hi, > > On Thu, May 17 2012, ludovic.desroches wrote: >>>> + remove soon (for more information have a look to >>> ^ removed >>>> + Documentation/feature-removal-schedule.txt). Please use >>>> + MMC_ATMEL_MCI. >>>> >>>> If unsure, say N. >> >> Sorry for the typo, do you want a new patch or is ok? > > It's okay, I've fixed it up here. > >>> Seems like I should take this patch 2/2, and then someone else should >>> merge 1/2? >> >> Yes, Nicolas would probably take patch 2/2. > > I think you must mean that Nicolas takes 1/2 (the arch/arm/ patches). > Assuming you do, that's fine and I've pushed 2/2 to mmc-next for 3.5 now. > > Thanks, > > - Chris. Fine. Thanks Ludovic ^ permalink raw reply [flat|nested] 28+ messages in thread
* [PATCH 2/2] mmc: at91-mci: this driver is now deprecated @ 2012-05-17 18:40 ` ludovic.desroches 0 siblings, 0 replies; 28+ messages in thread From: ludovic.desroches @ 2012-05-17 18:40 UTC (permalink / raw) To: linux-arm-kernel Le 05/17/2012 08:36 PM, Chris Ball a ?crit : > Hi, > > On Thu, May 17 2012, ludovic.desroches wrote: >>>> + remove soon (for more information have a look to >>> ^ removed >>>> + Documentation/feature-removal-schedule.txt). Please use >>>> + MMC_ATMEL_MCI. >>>> >>>> If unsure, say N. >> >> Sorry for the typo, do you want a new patch or is ok? > > It's okay, I've fixed it up here. > >>> Seems like I should take this patch 2/2, and then someone else should >>> merge 1/2? >> >> Yes, Nicolas would probably take patch 2/2. > > I think you must mean that Nicolas takes 1/2 (the arch/arm/ patches). > Assuming you do, that's fine and I've pushed 2/2 to mmc-next for 3.5 now. > > Thanks, > > - Chris. Fine. Thanks Ludovic ^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: [PATCH 2/2] mmc: at91-mci: this driver is now deprecated 2012-05-17 18:36 ` Chris Ball @ 2012-05-21 10:19 ` Nicolas Ferre -1 siblings, 0 replies; 28+ messages in thread From: Nicolas Ferre @ 2012-05-21 10:19 UTC (permalink / raw) To: Chris Ball, linux-arm-kernel, Arnd Bergmann, Olof Johansson Cc: linux-mmc, ludovic.desroches, plagnioj On 05/17/2012 08:36 PM, Chris Ball : > Hi, > > On Thu, May 17 2012, ludovic.desroches wrote: >>>> + remove soon (for more information have a look to >>> ^ removed >>>> + Documentation/feature-removal-schedule.txt). Please use >>>> + MMC_ATMEL_MCI. >>>> >>>> If unsure, say N. >> >> Sorry for the typo, do you want a new patch or is ok? > > It's okay, I've fixed it up here. > >>> Seems like I should take this patch 2/2, and then someone else should >>> merge 1/2? >> >> Yes, Nicolas would probably take patch 2/2. > > I think you must mean that Nicolas takes 1/2 (the arch/arm/ patches). > Assuming you do, that's fine and I've pushed 2/2 to mmc-next for 3.5 now. Ludovic and Chris, Sure, I will take 1/2 patch of this series through arm-soc. Unfortunately, it seems to be a bit late for 3.5... Anyway, I will talk with Arnd and Olof about the possibility to include it in a "late" or "staging" branch: that will allow this platform data addition to have some exposure in linux-next. We can also imagine that having a better support for atmel-mci driver in AT91 boards will help people gain a more stable system and avoid using a now "deprecated" driver that will be removed in 3.7. So I am personally in favor for an inclusion as soon as possible... Thanks, best regards, -- Nicolas Ferre ^ permalink raw reply [flat|nested] 28+ messages in thread
* [PATCH 2/2] mmc: at91-mci: this driver is now deprecated @ 2012-05-21 10:19 ` Nicolas Ferre 0 siblings, 0 replies; 28+ messages in thread From: Nicolas Ferre @ 2012-05-21 10:19 UTC (permalink / raw) To: linux-arm-kernel On 05/17/2012 08:36 PM, Chris Ball : > Hi, > > On Thu, May 17 2012, ludovic.desroches wrote: >>>> + remove soon (for more information have a look to >>> ^ removed >>>> + Documentation/feature-removal-schedule.txt). Please use >>>> + MMC_ATMEL_MCI. >>>> >>>> If unsure, say N. >> >> Sorry for the typo, do you want a new patch or is ok? > > It's okay, I've fixed it up here. > >>> Seems like I should take this patch 2/2, and then someone else should >>> merge 1/2? >> >> Yes, Nicolas would probably take patch 2/2. > > I think you must mean that Nicolas takes 1/2 (the arch/arm/ patches). > Assuming you do, that's fine and I've pushed 2/2 to mmc-next for 3.5 now. Ludovic and Chris, Sure, I will take 1/2 patch of this series through arm-soc. Unfortunately, it seems to be a bit late for 3.5... Anyway, I will talk with Arnd and Olof about the possibility to include it in a "late" or "staging" branch: that will allow this platform data addition to have some exposure in linux-next. We can also imagine that having a better support for atmel-mci driver in AT91 boards will help people gain a more stable system and avoid using a now "deprecated" driver that will be removed in 3.7. So I am personally in favor for an inclusion as soon as possible... Thanks, best regards, -- Nicolas Ferre ^ permalink raw reply [flat|nested] 28+ messages in thread
* [PATCH v2] ARM: at91: add atmel-mci support for chips and boards which can use it 2012-05-16 15:51 ` ludovic.desroches at atmel.com @ 2012-05-21 10:23 ` ludovic.desroches at atmel.com -1 siblings, 0 replies; 28+ messages in thread From: ludovic.desroches @ 2012-05-21 10:23 UTC (permalink / raw) To: linux-mmc, linux-arm-kernel; +Cc: nicolas.ferre, plagnioj, Ludovic Desroches From: Ludovic Desroches <ludovic.desroches@atmel.com> Since atmel-mci driver supports all atmel mci version excepted the rm9200 one, use it instead of at91_mci driver. Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> --- V2: add several boards I missed arch/arm/mach-at91/at91rm9200_devices.c | 99 ++++++++++++++++++ arch/arm/mach-at91/at91sam9261_devices.c | 67 ++++++++++++ arch/arm/mach-at91/at91sam9263.c | 2 + arch/arm/mach-at91/at91sam9263_devices.c | 164 ++++++++++++++++++++++++++++++ arch/arm/mach-at91/at91sam9rl_devices.c | 70 +++++++++++++ arch/arm/mach-at91/board-afeb-9260v1.c | 14 +++ arch/arm/mach-at91/board-carmeva.c | 14 +++ arch/arm/mach-at91/board-cpu9krea.c | 14 +++ arch/arm/mach-at91/board-cpuat91.c | 14 +++ arch/arm/mach-at91/board-csb337.c | 14 +++ arch/arm/mach-at91/board-eb9200.c | 14 +++ arch/arm/mach-at91/board-ecbat91.c | 14 +++ arch/arm/mach-at91/board-eco920.c | 14 +++ arch/arm/mach-at91/board-flexibity.c | 14 +++ arch/arm/mach-at91/board-foxg20.c | 16 +++- arch/arm/mach-at91/board-kb9202.c | 14 +++ arch/arm/mach-at91/board-neocore926.c | 14 +++ arch/arm/mach-at91/board-picotux200.c | 14 +++ arch/arm/mach-at91/board-qil-a9260.c | 14 +++ arch/arm/mach-at91/board-rm9200dk.c | 14 +++ arch/arm/mach-at91/board-rm9200ek.c | 14 +++ arch/arm/mach-at91/board-rsi-ews.c | 14 +++ arch/arm/mach-at91/board-sam9-l9260.c | 16 +++- arch/arm/mach-at91/board-sam9260ek.c | 16 +++- arch/arm/mach-at91/board-sam9261ek.c | 14 +++ arch/arm/mach-at91/board-sam9263ek.c | 14 +++ arch/arm/mach-at91/board-sam9rlek.c | 14 +++ arch/arm/mach-at91/board-usb-a926x.c | 2 +- arch/arm/mach-at91/board-yl-9200.c | 14 +++ 29 files changed, 728 insertions(+), 4 deletions(-) diff --git a/arch/arm/mach-at91/at91rm9200_devices.c b/arch/arm/mach-at91/at91rm9200_devices.c index 05774e5..2c13783 100644 --- a/arch/arm/mach-at91/at91rm9200_devices.c +++ b/arch/arm/mach-at91/at91rm9200_devices.c @@ -374,6 +374,105 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {} /* -------------------------------------------------------------------- + * MMC / SD + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static u64 mmc_dmamask = DMA_BIT_MASK(32); +static struct mci_platform_data mmc_data; + +static struct resource mmc_resources[] = { + [0] = { + .start = AT91RM9200_BASE_MCI, + .end = AT91RM9200_BASE_MCI + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91RM9200_ID_MCI, + .end = AT91RM9200_ID_MCI, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91rm9200_mmc_device = { + .name = "atmel_mci", + .id = -1, + .dev = { + .dma_mask = &mmc_dmamask, + .coherent_dma_mask = DMA_BIT_MASK(32), + .platform_data = &mmc_data, + }, + .resource = mmc_resources, + .num_resources = ARRAY_SIZE(mmc_resources), +}; + +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) +{ + unsigned int i; + unsigned int slot_count = 0; + + if (!data) + return; + + for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) { + + if (!data->slot[i].bus_width) + continue; + + /* input/irq */ + if (gpio_is_valid(data->slot[i].detect_pin)) { + at91_set_gpio_input(data->slot[i].detect_pin, 1); + at91_set_deglitch(data->slot[i].detect_pin, 1); + } + if (gpio_is_valid(data->slot[i].wp_pin)) + at91_set_gpio_input(data->slot[i].wp_pin, 1); + + switch (i) { + case 0: /* slot A */ + /* CMD */ + at91_set_A_periph(AT91_PIN_PA28, 1); + /* DAT0, maybe DAT1..DAT3 */ + at91_set_A_periph(AT91_PIN_PA29, 1); + if (data->slot[i].bus_width == 4) { + at91_set_B_periph(AT91_PIN_PB3, 1); + at91_set_B_periph(AT91_PIN_PB4, 1); + at91_set_B_periph(AT91_PIN_PB5, 1); + } + slot_count++; + break; + case 1: /* slot B */ + /* CMD */ + at91_set_B_periph(AT91_PIN_PA8, 1); + /* DAT0, maybe DAT1..DAT3 */ + at91_set_B_periph(AT91_PIN_PA9, 1); + if (data->slot[i].bus_width == 4) { + at91_set_B_periph(AT91_PIN_PA10, 1); + at91_set_B_periph(AT91_PIN_PA11, 1); + at91_set_B_periph(AT91_PIN_PA12, 1); + } + slot_count++; + break; + default: + printk(KERN_ERR + "AT91: SD/MMC slot %d not available\n", i); + break; + } + if (slot_count) { + /* CLK */ + at91_set_A_periph(AT91_PIN_PA27, 0); + + mmc_data = *data; + platform_device_register(&at91rm9200_mmc_device); + } + } + +} +#else +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {} +#endif + + +/* -------------------------------------------------------------------- * NAND / SmartMedia * -------------------------------------------------------------------- */ diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c index 4db961a..0817854 100644 --- a/arch/arm/mach-at91/at91sam9261_devices.c +++ b/arch/arm/mach-at91/at91sam9261_devices.c @@ -202,7 +202,74 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {} #endif +/* -------------------------------------------------------------------- + * MMC / SD Slot for Atmel MCI Driver + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static u64 mmc_dmamask = DMA_BIT_MASK(32); +static struct mci_platform_data mmc_data; + +static struct resource mmc_resources[] = { + [0] = { + .start = AT91SAM9261_BASE_MCI, + .end = AT91SAM9261_BASE_MCI + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9261_ID_MCI, + .end = AT91SAM9261_ID_MCI, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91sam9261_mmc_device = { + .name = "atmel_mci", + .id = -1, + .dev = { + .dma_mask = &mmc_dmamask, + .coherent_dma_mask = DMA_BIT_MASK(32), + .platform_data = &mmc_data, + }, + .resource = mmc_resources, + .num_resources = ARRAY_SIZE(mmc_resources), +}; + +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) +{ + if (!data) + return; + if (data->slot[0].bus_width) { + /* input/irq */ + if (gpio_is_valid(data->slot[0].detect_pin)) { + at91_set_gpio_input(data->slot[0].detect_pin, 1); + at91_set_deglitch(data->slot[0].detect_pin, 1); + } + if (gpio_is_valid(data->slot[0].wp_pin)) + at91_set_gpio_input(data->slot[0].wp_pin, 1); + + /* CLK */ + at91_set_B_periph(AT91_PIN_PA2, 0); + + /* CMD */ + at91_set_B_periph(AT91_PIN_PA1, 1); + + /* DAT0, maybe DAT1..DAT3 */ + at91_set_B_periph(AT91_PIN_PA0, 1); + if (data->slot[0].bus_width == 4) { + at91_set_B_periph(AT91_PIN_PA4, 1); + at91_set_B_periph(AT91_PIN_PA5, 1); + at91_set_B_periph(AT91_PIN_PA6, 1); + } + + mmc_data = *data; + platform_device_register(&at91sam9261_mmc_device); + } +} +#else +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {} +#endif /* -------------------------------------------------------------------- * NAND / SmartMedia * -------------------------------------------------------------------- */ diff --git a/arch/arm/mach-at91/at91sam9263.c b/arch/arm/mach-at91/at91sam9263.c index ef301be..053e47a 100644 --- a/arch/arm/mach-at91/at91sam9263.c +++ b/arch/arm/mach-at91/at91sam9263.c @@ -189,6 +189,8 @@ static struct clk_lookup periph_clocks_lookups[] = { CLKDEV_CON_DEV_ID("pclk", "ssc.1", &ssc1_clk), CLKDEV_CON_DEV_ID("mci_clk", "at91_mci.0", &mmc0_clk), CLKDEV_CON_DEV_ID("mci_clk", "at91_mci.1", &mmc1_clk), + CLKDEV_CON_DEV_ID("mci_clk", "atmel_mci.0", &mmc0_clk), + CLKDEV_CON_DEV_ID("mci_clk", "atmel_mci.1", &mmc1_clk), CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.0", &spi0_clk), CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.1", &spi1_clk), CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tcb_clk), diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c index fe99206..617fbfc 100644 --- a/arch/arm/mach-at91/at91sam9263_devices.c +++ b/arch/arm/mach-at91/at91sam9263_devices.c @@ -354,6 +354,170 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {} #endif /* -------------------------------------------------------------------- + * MMC / SD + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static u64 mmc_dmamask = DMA_BIT_MASK(32); +static struct mci_platform_data mmc0_data, mmc1_data; + +static struct resource mmc0_resources[] = { + [0] = { + .start = AT91SAM9263_BASE_MCI0, + .end = AT91SAM9263_BASE_MCI0 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9263_ID_MCI0, + .end = AT91SAM9263_ID_MCI0, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91sam9263_mmc0_device = { + .name = "atmel_mci", + .id = 0, + .dev = { + .dma_mask = &mmc_dmamask, + .coherent_dma_mask = DMA_BIT_MASK(32), + .platform_data = &mmc0_data, + }, + .resource = mmc0_resources, + .num_resources = ARRAY_SIZE(mmc0_resources), +}; + +static struct resource mmc1_resources[] = { + [0] = { + .start = AT91SAM9263_BASE_MCI1, + .end = AT91SAM9263_BASE_MCI1 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9263_ID_MCI1, + .end = AT91SAM9263_ID_MCI1, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91sam9263_mmc1_device = { + .name = "atmel_mci", + .id = 1, + .dev = { + .dma_mask = &mmc_dmamask, + .coherent_dma_mask = DMA_BIT_MASK(32), + .platform_data = &mmc1_data, + }, + .resource = mmc1_resources, + .num_resources = ARRAY_SIZE(mmc1_resources), +}; + +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) +{ + unsigned int i; + unsigned int slot_count = 0; + + if (!data) + return; + + for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) { + + if (!data->slot[i].bus_width) + continue; + + /* input/irq */ + if (gpio_is_valid(data->slot[i].detect_pin)) { + at91_set_gpio_input(data->slot[i].detect_pin, + 1); + at91_set_deglitch(data->slot[i].detect_pin, + 1); + } + if (gpio_is_valid(data->slot[i].wp_pin)) + at91_set_gpio_input(data->slot[i].wp_pin, 1); + + if (mmc_id == 0) { /* MCI0 */ + switch (i) { + case 0: /* slot A */ + /* CMD */ + at91_set_A_periph(AT91_PIN_PA1, 1); + /* DAT0, maybe DAT1..DAT3 */ + at91_set_A_periph(AT91_PIN_PA0, 1); + if (data->slot[i].bus_width == 4) { + at91_set_A_periph(AT91_PIN_PA3, 1); + at91_set_A_periph(AT91_PIN_PA4, 1); + at91_set_A_periph(AT91_PIN_PA5, 1); + } + slot_count++; + break; + case 1: /* slot B */ + /* CMD */ + at91_set_A_periph(AT91_PIN_PA16, 1); + /* DAT0, maybe DAT1..DAT3 */ + at91_set_A_periph(AT91_PIN_PA17, 1); + if (data->slot[i].bus_width == 4) { + at91_set_A_periph(AT91_PIN_PA18, 1); + at91_set_A_periph(AT91_PIN_PA19, 1); + at91_set_A_periph(AT91_PIN_PA20, 1); + } + slot_count++; + break; + default: + printk(KERN_ERR + "AT91: SD/MMC slot %d not available\n", i); + break; + } + if (slot_count) { + /* CLK */ + at91_set_A_periph(AT91_PIN_PA12, 0); + + mmc0_data = *data; + platform_device_register(&at91sam9263_mmc0_device); + } + } else if (mmc_id == 1) { /* MCI1 */ + switch (i) { + case 0: /* slot A */ + /* CMD */ + at91_set_A_periph(AT91_PIN_PA7, 1); + /* DAT0, maybe DAT1..DAT3 */ + at91_set_A_periph(AT91_PIN_PA8, 1); + if (data->slot[i].bus_width == 4) { + at91_set_A_periph(AT91_PIN_PA9, 1); + at91_set_A_periph(AT91_PIN_PA10, 1); + at91_set_A_periph(AT91_PIN_PA11, 1); + } + slot_count++; + break; + case 1: /* slot B */ + /* CMD */ + at91_set_A_periph(AT91_PIN_PA21, 1); + /* DAT0, maybe DAT1..DAT3 */ + at91_set_A_periph(AT91_PIN_PA22, 1); + if (data->slot[i].bus_width == 4) { + at91_set_A_periph(AT91_PIN_PA23, 1); + at91_set_A_periph(AT91_PIN_PA24, 1); + at91_set_A_periph(AT91_PIN_PA25, 1); + } + slot_count++; + break; + default: + printk(KERN_ERR + "AT91: SD/MMC slot %d not available\n", i); + break; + } + if (slot_count) { + /* CLK */ + at91_set_A_periph(AT91_PIN_PA6, 0); + + mmc1_data = *data; + platform_device_register(&at91sam9263_mmc1_device); + } + } + } +} +#else +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {} +#endif + +/* -------------------------------------------------------------------- * Compact Flash (PCMCIA or IDE) * -------------------------------------------------------------------- */ diff --git a/arch/arm/mach-at91/at91sam9rl_devices.c b/arch/arm/mach-at91/at91sam9rl_devices.c index fe4ae22..83c5845 100644 --- a/arch/arm/mach-at91/at91sam9rl_devices.c +++ b/arch/arm/mach-at91/at91sam9rl_devices.c @@ -228,6 +228,76 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {} /* -------------------------------------------------------------------- + * MMC / SD + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static u64 mmc_dmamask = DMA_BIT_MASK(32); +static struct mci_platform_data mmc_data; + +static struct resource mmc_resources[] = { + [0] = { + .start = AT91SAM9RL_BASE_MCI, + .end = AT91SAM9RL_BASE_MCI + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9RL_ID_MCI, + .end = AT91SAM9RL_ID_MCI, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91sam9rl_mmc_device = { + .name = "atmel_mci", + .id = -1, + .dev = { + .dma_mask = &mmc_dmamask, + .coherent_dma_mask = DMA_BIT_MASK(32), + .platform_data = &mmc_data, + }, + .resource = mmc_resources, + .num_resources = ARRAY_SIZE(mmc_resources), +}; + +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) +{ + if (!data) + return; + + if (data->slot[0].bus_width) { + /* input/irq */ + if (gpio_is_valid(data->slot[0].detect_pin)) { + at91_set_gpio_input(data->slot[0].detect_pin, 1); + at91_set_deglitch(data->slot[0].detect_pin, 1); + } + if (gpio_is_valid(data->slot[0].wp_pin)) + at91_set_gpio_input(data->slot[0].wp_pin, 1); + + /* CLK */ + at91_set_A_periph(AT91_PIN_PA2, 0); + + /* CMD */ + at91_set_A_periph(AT91_PIN_PA1, 1); + + /* DAT0, maybe DAT1..DAT3 */ + at91_set_A_periph(AT91_PIN_PA0, 1); + if (data->slot[0].bus_width == 4) { + at91_set_A_periph(AT91_PIN_PA3, 1); + at91_set_A_periph(AT91_PIN_PA4, 1); + at91_set_A_periph(AT91_PIN_PA5, 1); + } + + mmc_data = *data; + platform_device_register(&at91sam9rl_mmc_device); + } +} +#else +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {} +#endif + + +/* -------------------------------------------------------------------- * NAND / SmartMedia * -------------------------------------------------------------------- */ diff --git a/arch/arm/mach-at91/board-afeb-9260v1.c b/arch/arm/mach-at91/board-afeb-9260v1.c index 161efba..1e294ba 100644 --- a/arch/arm/mach-at91/board-afeb-9260v1.c +++ b/arch/arm/mach-at91/board-afeb-9260v1.c @@ -148,6 +148,15 @@ static struct atmel_nand_data __initdata afeb9260_nand_data = { /* * MCI (SD/MMC) */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata afeb9260_mci0_data = { + .slot[1] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PC9, + .wp_pin = AT91_PIN_PC4, + }, +}; +#else static struct at91_mmc_data __initdata afeb9260_mmc_data = { .det_pin = AT91_PIN_PC9, .wp_pin = AT91_PIN_PC4, @@ -155,6 +164,7 @@ static struct at91_mmc_data __initdata afeb9260_mmc_data = { .wire4 = 1, .vcc_pin = -EINVAL, }; +#endif @@ -202,7 +212,11 @@ static void __init afeb9260_board_init(void) at91_set_B_periph(AT91_PIN_PA10, 0); /* ETX2 */ at91_set_B_periph(AT91_PIN_PA11, 0); /* ETX3 */ /* MMC */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &afeb9260_mci0_data); +#else at91_add_device_mmc(0, &afeb9260_mmc_data); +#endif /* I2C */ at91_add_device_i2c(afeb9260_i2c_devices, ARRAY_SIZE(afeb9260_i2c_devices)); diff --git a/arch/arm/mach-at91/board-carmeva.c b/arch/arm/mach-at91/board-carmeva.c index 59d9cf9..050b9d5 100644 --- a/arch/arm/mach-at91/board-carmeva.c +++ b/arch/arm/mach-at91/board-carmeva.c @@ -81,6 +81,15 @@ static struct at91_udc_data __initdata carmeva_udc_data = { // .vcc_pin = -EINVAL, // }; +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata carmeva_mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PB10, + .wp_pin = AT91_PIN_PC14, + }, +}; +#else static struct at91_mmc_data __initdata carmeva_mmc_data = { .slot_b = 0, .wire4 = 1, @@ -88,6 +97,7 @@ static struct at91_mmc_data __initdata carmeva_mmc_data = { .wp_pin = AT91_PIN_PC14, .vcc_pin = -EINVAL, }; +#endif static struct spi_board_info carmeva_spi_devices[] = { { /* DataFlash chip */ @@ -153,7 +163,11 @@ static void __init carmeva_board_init(void) /* Compact Flash */ // at91_add_device_cf(&carmeva_cf_data); /* MMC */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &carmeva_mci0_data); +#else at91_add_device_mmc(0, &carmeva_mmc_data); +#endif /* LEDs */ at91_gpio_leds(carmeva_leds, ARRAY_SIZE(carmeva_leds)); } diff --git a/arch/arm/mach-at91/board-cpu9krea.c b/arch/arm/mach-at91/board-cpu9krea.c index 5f3680e..9842297 100644 --- a/arch/arm/mach-at91/board-cpu9krea.c +++ b/arch/arm/mach-at91/board-cpu9krea.c @@ -339,6 +339,15 @@ static void __init cpu9krea_add_device_buttons(void) /* * MCI (SD/MMC) */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata cpu9krea_mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PA29, + .wp_pin = -EINVAL, + }, +}; +#else static struct at91_mmc_data __initdata cpu9krea_mmc_data = { .slot_b = 0, .wire4 = 1, @@ -346,6 +355,7 @@ static struct at91_mmc_data __initdata cpu9krea_mmc_data = { .wp_pin = -EINVAL, .vcc_pin = -EINVAL, }; +#endif static void __init cpu9krea_board_init(void) { @@ -362,7 +372,11 @@ static void __init cpu9krea_board_init(void) /* Ethernet */ at91_add_device_eth(&cpu9krea_macb_data); /* MMC */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &cpu9krea_mci0_data); +#else at91_add_device_mmc(0, &cpu9krea_mmc_data); +#endif /* I2C */ at91_add_device_i2c(cpu9krea_i2c_devices, ARRAY_SIZE(cpu9krea_i2c_devices)); diff --git a/arch/arm/mach-at91/board-cpuat91.c b/arch/arm/mach-at91/board-cpuat91.c index e094cc8..cb5dcbf 100644 --- a/arch/arm/mach-at91/board-cpuat91.c +++ b/arch/arm/mach-at91/board-cpuat91.c @@ -99,12 +99,22 @@ static struct at91_udc_data __initdata cpuat91_udc_data = { .pullup_pin = AT91_PIN_PC14, }; +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata cpuat91_mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PC2, + .wp_pin = -EINVAL, + }, +}; +#else static struct at91_mmc_data __initdata cpuat91_mmc_data = { .det_pin = AT91_PIN_PC2, .wire4 = 1, .wp_pin = -EINVAL, .vcc_pin = -EINVAL, }; +#endif static struct physmap_flash_data cpuat91_flash_data = { .width = 2, @@ -171,7 +181,11 @@ static void __init cpuat91_board_init(void) /* USB Device */ at91_add_device_udc(&cpuat91_udc_data); /* MMC */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &cpuat91_mci0_data); +#else at91_add_device_mmc(0, &cpuat91_mmc_data); +#endif /* I2C */ at91_add_device_i2c(NULL, 0); /* Platform devices */ diff --git a/arch/arm/mach-at91/board-csb337.c b/arch/arm/mach-at91/board-csb337.c index 1a1547b..36d65ef 100644 --- a/arch/arm/mach-at91/board-csb337.c +++ b/arch/arm/mach-at91/board-csb337.c @@ -95,6 +95,15 @@ static struct at91_cf_data __initdata csb337_cf_data = { .rst_pin = AT91_PIN_PD2, }; +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata csb337_mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PD5, + .wp_pin = AT91_PIN_PD6, + }, +}; +#else static struct at91_mmc_data __initdata csb337_mmc_data = { .det_pin = AT91_PIN_PD5, .slot_b = 0, @@ -102,6 +111,7 @@ static struct at91_mmc_data __initdata csb337_mmc_data = { .wp_pin = AT91_PIN_PD6, .vcc_pin = -EINVAL, }; +#endif static struct spi_board_info csb337_spi_devices[] = { { /* CAN controller */ @@ -244,7 +254,11 @@ static void __init csb337_board_init(void) /* SPI */ at91_add_device_spi(csb337_spi_devices, ARRAY_SIZE(csb337_spi_devices)); /* MMC */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &csb337_mci0_data); +#else at91_add_device_mmc(0, &csb337_mmc_data); +#endif /* NOR flash */ platform_device_register(&csb_flash); /* LEDs */ diff --git a/arch/arm/mach-at91/board-eb9200.c b/arch/arm/mach-at91/board-eb9200.c index d302ca3..f374ecc 100644 --- a/arch/arm/mach-at91/board-eb9200.c +++ b/arch/arm/mach-at91/board-eb9200.c @@ -83,6 +83,15 @@ static struct at91_cf_data __initdata eb9200_cf_data = { .rst_pin = AT91_PIN_PC5, }; +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata eb9200_mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = -EINVAL, + .wp_pin = -EINVAL, + }, +}; +#else static struct at91_mmc_data __initdata eb9200_mmc_data = { .slot_b = 0, .wire4 = 1, @@ -90,6 +99,7 @@ static struct at91_mmc_data __initdata eb9200_mmc_data = { .wp_pin = -EINVAL, .vcc_pin = -EINVAL, }; +#endif static struct i2c_board_info __initdata eb9200_i2c_devices[] = { { @@ -116,7 +126,11 @@ static void __init eb9200_board_init(void) at91_add_device_spi(NULL, 0); /* MMC */ /* only supports 1 or 4 bit interface, not wired through to SPI */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &eb9200_mci0_data); +#else at91_add_device_mmc(0, &eb9200_mmc_data); +#endif } MACHINE_START(ATEB9200, "Embest ATEB9200") diff --git a/arch/arm/mach-at91/board-ecbat91.c b/arch/arm/mach-at91/board-ecbat91.c index 69966ce..0f39fb3 100644 --- a/arch/arm/mach-at91/board-ecbat91.c +++ b/arch/arm/mach-at91/board-ecbat91.c @@ -75,6 +75,15 @@ static struct at91_usbh_data __initdata ecb_at91usbh_data = { .overcurrent_pin= {-EINVAL, -EINVAL}, }; +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata ecbat91_mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = -EINVAL, + .wp_pin = -EINVAL, + }, +}; +#else static struct at91_mmc_data __initdata ecb_at91mmc_data = { .slot_b = 0, .wire4 = 1, @@ -82,6 +91,7 @@ static struct at91_mmc_data __initdata ecb_at91mmc_data = { .wp_pin = -EINVAL, .vcc_pin = -EINVAL, }; +#endif #if defined(CONFIG_MTD_DATAFLASH) @@ -164,7 +174,11 @@ static void __init ecb_at91board_init(void) at91_add_device_i2c(NULL, 0); /* MMC */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &ecbat91_mci0_data); +#else at91_add_device_mmc(0, &ecb_at91mmc_data); +#endif /* SPI */ at91_add_device_spi(ecb_at91spi_devices, ARRAY_SIZE(ecb_at91spi_devices)); diff --git a/arch/arm/mach-at91/board-eco920.c b/arch/arm/mach-at91/board-eco920.c index f23aabe..932bebd 100644 --- a/arch/arm/mach-at91/board-eco920.c +++ b/arch/arm/mach-at91/board-eco920.c @@ -64,6 +64,15 @@ static struct at91_udc_data __initdata eco920_udc_data = { .pullup_pin = AT91_PIN_PB13, }; +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata eco920_mci0_data = { + .slot[0] = { + .bus_width = 1, + .detect_pin = -EINVAL, + .wp_pin = -EINVAL, + }, +}; +#else static struct at91_mmc_data __initdata eco920_mmc_data = { .slot_b = 0, .wire4 = 0, @@ -71,6 +80,7 @@ static struct at91_mmc_data __initdata eco920_mmc_data = { .wp_pin = -EINVAL, .vcc_pin = -EINVAL, }; +#endif static struct physmap_flash_data eco920_flash_data = { .width = 2, @@ -108,7 +118,11 @@ static void __init eco920_board_init(void) at91_add_device_usbh(&eco920_usbh_data); at91_add_device_udc(&eco920_udc_data); +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &eco920_mci0_data); +#else at91_add_device_mmc(0, &eco920_mmc_data); +#endif platform_device_register(&eco920_flash); at91_ramc_write(0, AT91_SMC_CSR(7), AT91_SMC_RWHOLD_(1) diff --git a/arch/arm/mach-at91/board-flexibity.c b/arch/arm/mach-at91/board-flexibity.c index 1815152..6632a80 100644 --- a/arch/arm/mach-at91/board-flexibity.c +++ b/arch/arm/mach-at91/board-flexibity.c @@ -80,6 +80,15 @@ static struct spi_board_info flexibity_spi_devices[] = { }; /* MCI (SD/MMC) */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata flexibity_mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PC9, + .wp_pin = AT91_PIN_PC4, + }, +}; +#else static struct at91_mmc_data __initdata flexibity_mmc_data = { .slot_b = 0, .wire4 = 1, @@ -87,6 +96,7 @@ static struct at91_mmc_data __initdata flexibity_mmc_data = { .wp_pin = AT91_PIN_PC4, .vcc_pin = -EINVAL, }; +#endif /* LEDs */ static struct gpio_led flexibity_leds[] = { @@ -155,7 +165,11 @@ static void __init flexibity_board_init(void) at91_add_device_spi(flexibity_spi_devices, ARRAY_SIZE(flexibity_spi_devices)); /* MMC */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &flexibity_mci0_data); +#else at91_add_device_mmc(0, &flexibity_mmc_data); +#endif /* LEDs */ at91_gpio_leds(flexibity_leds, ARRAY_SIZE(flexibity_leds)); } diff --git a/arch/arm/mach-at91/board-foxg20.c b/arch/arm/mach-at91/board-foxg20.c index caf017f..6cda303 100644 --- a/arch/arm/mach-at91/board-foxg20.c +++ b/arch/arm/mach-at91/board-foxg20.c @@ -123,7 +123,7 @@ static struct at91_udc_data __initdata foxg20_udc_data = { * SPI devices. */ static struct spi_board_info foxg20_spi_devices[] = { -#if !defined(CONFIG_MMC_AT91) +#if !defined(CONFIG_MMC_AT91) && !defined(CONFIG_MMC_ATMELMCI) { .modalias = "mtd_dataflash", .chip_select = 1, @@ -146,6 +146,7 @@ static struct macb_platform_data __initdata foxg20_macb_data = { * MCI (SD/MMC) * det_pin, wp_pin and vcc_pin are not connected */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) static struct at91_mmc_data __initdata foxg20_mmc_data = { .slot_b = 1, .wire4 = 1, @@ -153,6 +154,15 @@ static struct at91_mmc_data __initdata foxg20_mmc_data = { .wp_pin = -EINVAL, .vcc_pin = -EINVAL, }; +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata foxg20_mci0_data = { + .slot[1] = { + .bus_width = 4, + .detect_pin = -EINVAL, + .wp_pin = -EINVAL, + }, +}; +#endif /* @@ -251,7 +261,11 @@ static void __init foxg20_board_init(void) /* Ethernet */ at91_add_device_eth(&foxg20_macb_data); /* MMC */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) at91_add_device_mmc(0, &foxg20_mmc_data); +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &foxg20_mci0_data); +#endif /* I2C */ at91_add_device_i2c(foxg20_i2c_devices, ARRAY_SIZE(foxg20_i2c_devices)); /* LEDs */ diff --git a/arch/arm/mach-at91/board-kb9202.c b/arch/arm/mach-at91/board-kb9202.c index 59b92aa..e31ec8e 100644 --- a/arch/arm/mach-at91/board-kb9202.c +++ b/arch/arm/mach-at91/board-kb9202.c @@ -86,6 +86,15 @@ static struct at91_udc_data __initdata kb9202_udc_data = { .pullup_pin = AT91_PIN_PB22, }; +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata kb9202_mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PB2, + .wp_pin = -EINVAL, + }, +}; +#else static struct at91_mmc_data __initdata kb9202_mmc_data = { .det_pin = AT91_PIN_PB2, .slot_b = 0, @@ -93,6 +102,7 @@ static struct at91_mmc_data __initdata kb9202_mmc_data = { .wp_pin = -EINVAL, .vcc_pin = -EINVAL, }; +#endif static struct mtd_partition __initdata kb9202_nand_partition[] = { { @@ -124,7 +134,11 @@ static void __init kb9202_board_init(void) /* USB Device */ at91_add_device_udc(&kb9202_udc_data); /* MMC */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &kb9202_mci0_data); +#else at91_add_device_mmc(0, &kb9202_mmc_data); +#endif /* I2C */ at91_add_device_i2c(NULL, 0); /* SPI */ diff --git a/arch/arm/mach-at91/board-neocore926.c b/arch/arm/mach-at91/board-neocore926.c index 57d5f6a..849b938 100644 --- a/arch/arm/mach-at91/board-neocore926.c +++ b/arch/arm/mach-at91/board-neocore926.c @@ -146,12 +146,22 @@ static struct spi_board_info neocore926_spi_devices[] = { /* * MCI (SD/MMC) */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata neocore926_mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PE18, + .wp_pin = AT91_PIN_PE19, + }, +}; +#else static struct at91_mmc_data __initdata neocore926_mmc_data = { .wire4 = 1, .det_pin = AT91_PIN_PE18, .wp_pin = AT91_PIN_PE19, .vcc_pin = -EINVAL, }; +#endif /* @@ -357,7 +367,11 @@ static void __init neocore926_board_init(void) neocore926_add_device_ts(); /* MMC */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &neocore926_mci0_data); +#else at91_add_device_mmc(1, &neocore926_mmc_data); +#endif /* Ethernet */ at91_add_device_eth(&neocore926_macb_data); diff --git a/arch/arm/mach-at91/board-picotux200.c b/arch/arm/mach-at91/board-picotux200.c index 59e35dd..a8cb032 100644 --- a/arch/arm/mach-at91/board-picotux200.c +++ b/arch/arm/mach-at91/board-picotux200.c @@ -72,6 +72,15 @@ static struct at91_usbh_data __initdata picotux200_usbh_data = { .overcurrent_pin= {-EINVAL, -EINVAL}, }; +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata picotux200_mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PB27, + .wp_pin = AT91_PIN_PA17, + }, +}; +#else static struct at91_mmc_data __initdata picotux200_mmc_data = { .det_pin = AT91_PIN_PB27, .slot_b = 0, @@ -79,6 +88,7 @@ static struct at91_mmc_data __initdata picotux200_mmc_data = { .wp_pin = AT91_PIN_PA17, .vcc_pin = -EINVAL, }; +#endif #define PICOTUX200_FLASH_BASE AT91_CHIPSELECT_0 #define PICOTUX200_FLASH_SIZE SZ_4M @@ -115,7 +125,11 @@ static void __init picotux200_board_init(void) at91_add_device_i2c(NULL, 0); /* MMC */ at91_set_gpio_output(AT91_PIN_PB22, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &picotux200_mci0_data); +#else at91_add_device_mmc(0, &picotux200_mmc_data); +#endif /* NOR Flash */ platform_device_register(&picotux200_flash); } diff --git a/arch/arm/mach-at91/board-qil-a9260.c b/arch/arm/mach-at91/board-qil-a9260.c index b6ed5ed..2a49993 100644 --- a/arch/arm/mach-at91/board-qil-a9260.c +++ b/arch/arm/mach-at91/board-qil-a9260.c @@ -173,6 +173,15 @@ static void __init ek_add_device_nand(void) /* * MCI (SD/MMC) */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata ek_mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = -EINVAL, + .wp_pin = -EINVAL, + }, +}; +#else static struct at91_mmc_data __initdata ek_mmc_data = { .slot_b = 0, .wire4 = 1, @@ -180,6 +189,7 @@ static struct at91_mmc_data __initdata ek_mmc_data = { .wp_pin = -EINVAL, .vcc_pin = -EINVAL, }; +#endif /* * GPIO Buttons @@ -249,7 +259,11 @@ static void __init ek_board_init(void) /* Ethernet */ at91_add_device_eth(&ek_macb_data); /* MMC */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &ek_mci0_data); +#else at91_add_device_mmc(0, &ek_mmc_data); +#endif /* Push Buttons */ ek_add_device_buttons(); /* LEDs */ diff --git a/arch/arm/mach-at91/board-rm9200dk.c b/arch/arm/mach-at91/board-rm9200dk.c index 01332aa..b6128fb 100644 --- a/arch/arm/mach-at91/board-rm9200dk.c +++ b/arch/arm/mach-at91/board-rm9200dk.c @@ -90,6 +90,15 @@ static struct at91_cf_data __initdata dk_cf_data = { }; #ifndef CONFIG_MTD_AT91_DATAFLASH_CARD +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata dk_mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = -EINVAL, + .wp_pin = -EINVAL, + }, +}; +#else static struct at91_mmc_data __initdata dk_mmc_data = { .slot_b = 0, .wire4 = 1, @@ -98,6 +107,7 @@ static struct at91_mmc_data __initdata dk_mmc_data = { .vcc_pin = -EINVAL, }; #endif +#endif static struct spi_board_info dk_spi_devices[] = { { /* DataFlash chip */ @@ -211,8 +221,12 @@ static void __init dk_board_init(void) #else /* MMC */ at91_set_gpio_output(AT91_PIN_PB7, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &dk_mci0_data); +#else at91_add_device_mmc(0, &dk_mmc_data); #endif +#endif /* NAND */ at91_add_device_nand(&dk_nand_data); /* NOR Flash */ diff --git a/arch/arm/mach-at91/board-rm9200ek.c b/arch/arm/mach-at91/board-rm9200ek.c index b2e4fe2..7177aac 100644 --- a/arch/arm/mach-at91/board-rm9200ek.c +++ b/arch/arm/mach-at91/board-rm9200ek.c @@ -83,6 +83,7 @@ static struct at91_udc_data __initdata ek_udc_data = { }; #ifndef CONFIG_MTD_AT91_DATAFLASH_CARD +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) static struct at91_mmc_data __initdata ek_mmc_data = { .det_pin = AT91_PIN_PB27, .slot_b = 0, @@ -90,6 +91,15 @@ static struct at91_mmc_data __initdata ek_mmc_data = { .wp_pin = AT91_PIN_PA17, .vcc_pin = -EINVAL, }; +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata ek_mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PB27, + .wp_pin = AT91_PIN_PA17, + } +}; +#endif #endif static struct spi_board_info ek_spi_devices[] = { @@ -180,7 +190,11 @@ static void __init ek_board_init(void) #else /* MMC */ at91_set_gpio_output(AT91_PIN_PB22, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) at91_add_device_mmc(0, &ek_mmc_data); +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &ek_mci0_data); +#endif #endif /* NOR Flash */ platform_device_register(&ek_flash); diff --git a/arch/arm/mach-at91/board-rsi-ews.c b/arch/arm/mach-at91/board-rsi-ews.c index af0750f..373537a 100644 --- a/arch/arm/mach-at91/board-rsi-ews.c +++ b/arch/arm/mach-at91/board-rsi-ews.c @@ -77,12 +77,22 @@ static struct at91_usbh_data rsi_ews_usbh_data __initdata = { /* * SD/MC */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata rsi_ews_mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PB27, + .wp_pin = AT91_PIN_PB29, + }, +}; +#else static struct at91_mmc_data rsi_ews_mmc_data __initdata = { .slot_b = 0, .wire4 = 1, .det_pin = AT91_PIN_PB27, .wp_pin = AT91_PIN_PB29, }; +#endif /* * I2C @@ -218,7 +228,11 @@ static void __init rsi_ews_board_init(void) at91_add_device_spi(rsi_ews_spi_devices, ARRAY_SIZE(rsi_ews_spi_devices)); /* MMC */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &rsi_ews_mci0_data); +#else at91_add_device_mmc(0, &rsi_ews_mmc_data); +#endif /* NOR Flash */ platform_device_register(&rsiews_nor_flash); /* LEDs */ diff --git a/arch/arm/mach-at91/board-sam9-l9260.c b/arch/arm/mach-at91/board-sam9-l9260.c index e8b116b..7562011 100644 --- a/arch/arm/mach-at91/board-sam9-l9260.c +++ b/arch/arm/mach-at91/board-sam9-l9260.c @@ -89,7 +89,7 @@ static struct at91_udc_data __initdata ek_udc_data = { * SPI devices. */ static struct spi_board_info ek_spi_devices[] = { -#if !defined(CONFIG_MMC_AT91) +#if !defined(CONFIG_MMC_AT91) && !defined(CONFIG_MMC_ATMELMCI) { /* DataFlash chip */ .modalias = "mtd_dataflash", .chip_select = 1, @@ -174,6 +174,15 @@ static void __init ek_add_device_nand(void) /* * MCI (SD/MMC) */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata ek_mci0_data = { + .slot[1] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PC8, + .wp_pin = AT91_PIN_PC4, + }, +}; +#else static struct at91_mmc_data __initdata ek_mmc_data = { .slot_b = 1, .wire4 = 1, @@ -181,6 +190,7 @@ static struct at91_mmc_data __initdata ek_mmc_data = { .wp_pin = AT91_PIN_PC4, .vcc_pin = -EINVAL, }; +#endif static void __init ek_board_init(void) { @@ -197,7 +207,11 @@ static void __init ek_board_init(void) /* Ethernet */ at91_add_device_eth(&ek_macb_data); /* MMC */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &ek_mci0_data); +#else at91_add_device_mmc(0, &ek_mmc_data); +#endif /* I2C */ at91_add_device_i2c(NULL, 0); } diff --git a/arch/arm/mach-at91/board-sam9260ek.c b/arch/arm/mach-at91/board-sam9260ek.c index d5aec55..b39009e 100644 --- a/arch/arm/mach-at91/board-sam9260ek.c +++ b/arch/arm/mach-at91/board-sam9260ek.c @@ -121,7 +121,7 @@ static void __init at73c213_set_clk(struct at73c213_board_info *info) {} * SPI devices. */ static struct spi_board_info ek_spi_devices[] = { -#if !defined(CONFIG_MMC_AT91) +#if !defined(CONFIG_MMC_AT91) && !defined(CONFIG_MMC_ATMELMCI) { /* DataFlash chip */ .modalias = "mtd_dataflash", .chip_select = 1, @@ -224,6 +224,15 @@ static void __init ek_add_device_nand(void) /* * MCI (SD/MMC) */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata ek_mci0_data = { + .slot[1] = { + .bus_width = 4, + .detect_pin = -EINVAL, + .wp_pin = -EINVAL, + }, +}; +#else static struct at91_mmc_data __initdata ek_mmc_data = { .slot_b = 1, .wire4 = 1, @@ -231,6 +240,7 @@ static struct at91_mmc_data __initdata ek_mmc_data = { .wp_pin = -EINVAL, .vcc_pin = -EINVAL, }; +#endif /* @@ -332,7 +342,11 @@ static void __init ek_board_init(void) /* Ethernet */ at91_add_device_eth(&ek_macb_data); /* MMC */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &ek_mci0_data); +#else at91_add_device_mmc(0, &ek_mmc_data); +#endif /* I2C */ at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices)); /* SSC (to AT73C213) */ diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c index 065fed3..797dd7c 100644 --- a/arch/arm/mach-at91/board-sam9261ek.c +++ b/arch/arm/mach-at91/board-sam9261ek.c @@ -344,6 +344,7 @@ static struct spi_board_info ek_spi_devices[] = { #else /* CONFIG_SPI_ATMEL_* */ /* spi0 and mmc/sd share the same PIO pins: cannot be used at the same time */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) /* * MCI (SD/MMC) * det_pin, wp_pin and vcc_pin are not connected @@ -354,6 +355,15 @@ static struct at91_mmc_data __initdata ek_mmc_data = { .wp_pin = -EINVAL, .vcc_pin = -EINVAL, }; +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = -EINVAL, + .wp_pin = -EINVAL, + }, +}; +#endif #endif /* CONFIG_SPI_ATMEL_* */ @@ -601,7 +611,11 @@ static void __init ek_board_init(void) at91_add_device_ssc(AT91SAM9261_ID_SSC1, ATMEL_SSC_TX); #else /* MMC */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) at91_add_device_mmc(0, &ek_mmc_data); +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &mci0_data); +#endif #endif /* LCD Controller */ at91_add_device_lcdc(&ek_lcdc_data); diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c index 2ffe50f..419c57a 100644 --- a/arch/arm/mach-at91/board-sam9263ek.c +++ b/arch/arm/mach-at91/board-sam9263ek.c @@ -149,12 +149,22 @@ static struct spi_board_info ek_spi_devices[] = { /* * MCI (SD/MMC) */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata mci1_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PE18, + .wp_pin = AT91_PIN_PE19, + }, +}; +#else static struct at91_mmc_data __initdata ek_mmc_data = { .wire4 = 1, .det_pin = AT91_PIN_PE18, .wp_pin = AT91_PIN_PE19, .vcc_pin = -EINVAL, }; +#endif /* @@ -423,7 +433,11 @@ static void __init ek_board_init(void) /* Touchscreen */ ek_add_device_ts(); /* MMC */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(1, &mci1_data); +#else at91_add_device_mmc(1, &ek_mmc_data); +#endif /* Ethernet */ at91_add_device_eth(&ek_macb_data); /* NAND */ diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c index b109ce2..bb06521 100644 --- a/arch/arm/mach-at91/board-sam9rlek.c +++ b/arch/arm/mach-at91/board-sam9rlek.c @@ -64,12 +64,22 @@ static struct usba_platform_data __initdata ek_usba_udc_data = { /* * MCI (SD/MMC) */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) static struct at91_mmc_data __initdata ek_mmc_data = { .wire4 = 1, .det_pin = AT91_PIN_PA15, .wp_pin = -EINVAL, .vcc_pin = -EINVAL, }; +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PA15, + .wp_pin = -EINVAL, + }, +}; +#endif /* @@ -306,7 +316,11 @@ static void __init ek_board_init(void) /* SPI */ at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); /* MMC */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) at91_add_device_mmc(0, &ek_mmc_data); +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &mci0_data); +#endif /* LCD Controller */ at91_add_device_lcdc(&ek_lcdc_data); /* AC97 */ diff --git a/arch/arm/mach-at91/board-usb-a926x.c b/arch/arm/mach-at91/board-usb-a926x.c index b7483a3..879e34e 100644 --- a/arch/arm/mach-at91/board-usb-a926x.c +++ b/arch/arm/mach-at91/board-usb-a926x.c @@ -114,7 +114,7 @@ static struct mmc_spi_platform_data at91_mmc_spi_pdata = { * SPI devices. */ static struct spi_board_info usb_a9263_spi_devices[] = { -#if !defined(CONFIG_MMC_AT91) +#if !defined(CONFIG_MMC_AT91) && !defined(CONFIG_MMC_ATMELMCI) { /* DataFlash chip */ .modalias = "mtd_dataflash", .chip_select = 0, diff --git a/arch/arm/mach-at91/board-yl-9200.c b/arch/arm/mach-at91/board-yl-9200.c index 38dd279..3d3b8a6 100644 --- a/arch/arm/mach-at91/board-yl-9200.c +++ b/arch/arm/mach-at91/board-yl-9200.c @@ -138,12 +138,22 @@ static struct at91_udc_data __initdata yl9200_udc_data = { /* * MMC */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata yl9200_mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PB9, + .wp_pin = -EINVAL, + }, +}; +#else static struct at91_mmc_data __initdata yl9200_mmc_data = { .det_pin = AT91_PIN_PB9, .wire4 = 1, .wp_pin = -EINVAL, .vcc_pin = -EINVAL, }; +#endif /* * NAND Flash @@ -571,7 +581,11 @@ static void __init yl9200_board_init(void) /* I2C */ at91_add_device_i2c(yl9200_i2c_devices, ARRAY_SIZE(yl9200_i2c_devices)); /* MMC */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &yl9200_mci0_data); +#else at91_add_device_mmc(0, &yl9200_mmc_data); +#endif /* NAND */ at91_add_device_nand(&yl9200_nand_data); /* NOR Flash */ -- 1.7.5.4 ^ permalink raw reply related [flat|nested] 28+ messages in thread
* [PATCH v2] ARM: at91: add atmel-mci support for chips and boards which can use it @ 2012-05-21 10:23 ` ludovic.desroches at atmel.com 0 siblings, 0 replies; 28+ messages in thread From: ludovic.desroches at atmel.com @ 2012-05-21 10:23 UTC (permalink / raw) To: linux-arm-kernel From: Ludovic Desroches <ludovic.desroches@atmel.com> Since atmel-mci driver supports all atmel mci version excepted the rm9200 one, use it instead of at91_mci driver. Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> --- V2: add several boards I missed arch/arm/mach-at91/at91rm9200_devices.c | 99 ++++++++++++++++++ arch/arm/mach-at91/at91sam9261_devices.c | 67 ++++++++++++ arch/arm/mach-at91/at91sam9263.c | 2 + arch/arm/mach-at91/at91sam9263_devices.c | 164 ++++++++++++++++++++++++++++++ arch/arm/mach-at91/at91sam9rl_devices.c | 70 +++++++++++++ arch/arm/mach-at91/board-afeb-9260v1.c | 14 +++ arch/arm/mach-at91/board-carmeva.c | 14 +++ arch/arm/mach-at91/board-cpu9krea.c | 14 +++ arch/arm/mach-at91/board-cpuat91.c | 14 +++ arch/arm/mach-at91/board-csb337.c | 14 +++ arch/arm/mach-at91/board-eb9200.c | 14 +++ arch/arm/mach-at91/board-ecbat91.c | 14 +++ arch/arm/mach-at91/board-eco920.c | 14 +++ arch/arm/mach-at91/board-flexibity.c | 14 +++ arch/arm/mach-at91/board-foxg20.c | 16 +++- arch/arm/mach-at91/board-kb9202.c | 14 +++ arch/arm/mach-at91/board-neocore926.c | 14 +++ arch/arm/mach-at91/board-picotux200.c | 14 +++ arch/arm/mach-at91/board-qil-a9260.c | 14 +++ arch/arm/mach-at91/board-rm9200dk.c | 14 +++ arch/arm/mach-at91/board-rm9200ek.c | 14 +++ arch/arm/mach-at91/board-rsi-ews.c | 14 +++ arch/arm/mach-at91/board-sam9-l9260.c | 16 +++- arch/arm/mach-at91/board-sam9260ek.c | 16 +++- arch/arm/mach-at91/board-sam9261ek.c | 14 +++ arch/arm/mach-at91/board-sam9263ek.c | 14 +++ arch/arm/mach-at91/board-sam9rlek.c | 14 +++ arch/arm/mach-at91/board-usb-a926x.c | 2 +- arch/arm/mach-at91/board-yl-9200.c | 14 +++ 29 files changed, 728 insertions(+), 4 deletions(-) diff --git a/arch/arm/mach-at91/at91rm9200_devices.c b/arch/arm/mach-at91/at91rm9200_devices.c index 05774e5..2c13783 100644 --- a/arch/arm/mach-at91/at91rm9200_devices.c +++ b/arch/arm/mach-at91/at91rm9200_devices.c @@ -374,6 +374,105 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {} /* -------------------------------------------------------------------- + * MMC / SD + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static u64 mmc_dmamask = DMA_BIT_MASK(32); +static struct mci_platform_data mmc_data; + +static struct resource mmc_resources[] = { + [0] = { + .start = AT91RM9200_BASE_MCI, + .end = AT91RM9200_BASE_MCI + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91RM9200_ID_MCI, + .end = AT91RM9200_ID_MCI, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91rm9200_mmc_device = { + .name = "atmel_mci", + .id = -1, + .dev = { + .dma_mask = &mmc_dmamask, + .coherent_dma_mask = DMA_BIT_MASK(32), + .platform_data = &mmc_data, + }, + .resource = mmc_resources, + .num_resources = ARRAY_SIZE(mmc_resources), +}; + +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) +{ + unsigned int i; + unsigned int slot_count = 0; + + if (!data) + return; + + for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) { + + if (!data->slot[i].bus_width) + continue; + + /* input/irq */ + if (gpio_is_valid(data->slot[i].detect_pin)) { + at91_set_gpio_input(data->slot[i].detect_pin, 1); + at91_set_deglitch(data->slot[i].detect_pin, 1); + } + if (gpio_is_valid(data->slot[i].wp_pin)) + at91_set_gpio_input(data->slot[i].wp_pin, 1); + + switch (i) { + case 0: /* slot A */ + /* CMD */ + at91_set_A_periph(AT91_PIN_PA28, 1); + /* DAT0, maybe DAT1..DAT3 */ + at91_set_A_periph(AT91_PIN_PA29, 1); + if (data->slot[i].bus_width == 4) { + at91_set_B_periph(AT91_PIN_PB3, 1); + at91_set_B_periph(AT91_PIN_PB4, 1); + at91_set_B_periph(AT91_PIN_PB5, 1); + } + slot_count++; + break; + case 1: /* slot B */ + /* CMD */ + at91_set_B_periph(AT91_PIN_PA8, 1); + /* DAT0, maybe DAT1..DAT3 */ + at91_set_B_periph(AT91_PIN_PA9, 1); + if (data->slot[i].bus_width == 4) { + at91_set_B_periph(AT91_PIN_PA10, 1); + at91_set_B_periph(AT91_PIN_PA11, 1); + at91_set_B_periph(AT91_PIN_PA12, 1); + } + slot_count++; + break; + default: + printk(KERN_ERR + "AT91: SD/MMC slot %d not available\n", i); + break; + } + if (slot_count) { + /* CLK */ + at91_set_A_periph(AT91_PIN_PA27, 0); + + mmc_data = *data; + platform_device_register(&at91rm9200_mmc_device); + } + } + +} +#else +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {} +#endif + + +/* -------------------------------------------------------------------- * NAND / SmartMedia * -------------------------------------------------------------------- */ diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c index 4db961a..0817854 100644 --- a/arch/arm/mach-at91/at91sam9261_devices.c +++ b/arch/arm/mach-at91/at91sam9261_devices.c @@ -202,7 +202,74 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {} #endif +/* -------------------------------------------------------------------- + * MMC / SD Slot for Atmel MCI Driver + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static u64 mmc_dmamask = DMA_BIT_MASK(32); +static struct mci_platform_data mmc_data; + +static struct resource mmc_resources[] = { + [0] = { + .start = AT91SAM9261_BASE_MCI, + .end = AT91SAM9261_BASE_MCI + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9261_ID_MCI, + .end = AT91SAM9261_ID_MCI, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91sam9261_mmc_device = { + .name = "atmel_mci", + .id = -1, + .dev = { + .dma_mask = &mmc_dmamask, + .coherent_dma_mask = DMA_BIT_MASK(32), + .platform_data = &mmc_data, + }, + .resource = mmc_resources, + .num_resources = ARRAY_SIZE(mmc_resources), +}; + +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) +{ + if (!data) + return; + if (data->slot[0].bus_width) { + /* input/irq */ + if (gpio_is_valid(data->slot[0].detect_pin)) { + at91_set_gpio_input(data->slot[0].detect_pin, 1); + at91_set_deglitch(data->slot[0].detect_pin, 1); + } + if (gpio_is_valid(data->slot[0].wp_pin)) + at91_set_gpio_input(data->slot[0].wp_pin, 1); + + /* CLK */ + at91_set_B_periph(AT91_PIN_PA2, 0); + + /* CMD */ + at91_set_B_periph(AT91_PIN_PA1, 1); + + /* DAT0, maybe DAT1..DAT3 */ + at91_set_B_periph(AT91_PIN_PA0, 1); + if (data->slot[0].bus_width == 4) { + at91_set_B_periph(AT91_PIN_PA4, 1); + at91_set_B_periph(AT91_PIN_PA5, 1); + at91_set_B_periph(AT91_PIN_PA6, 1); + } + + mmc_data = *data; + platform_device_register(&at91sam9261_mmc_device); + } +} +#else +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {} +#endif /* -------------------------------------------------------------------- * NAND / SmartMedia * -------------------------------------------------------------------- */ diff --git a/arch/arm/mach-at91/at91sam9263.c b/arch/arm/mach-at91/at91sam9263.c index ef301be..053e47a 100644 --- a/arch/arm/mach-at91/at91sam9263.c +++ b/arch/arm/mach-at91/at91sam9263.c @@ -189,6 +189,8 @@ static struct clk_lookup periph_clocks_lookups[] = { CLKDEV_CON_DEV_ID("pclk", "ssc.1", &ssc1_clk), CLKDEV_CON_DEV_ID("mci_clk", "at91_mci.0", &mmc0_clk), CLKDEV_CON_DEV_ID("mci_clk", "at91_mci.1", &mmc1_clk), + CLKDEV_CON_DEV_ID("mci_clk", "atmel_mci.0", &mmc0_clk), + CLKDEV_CON_DEV_ID("mci_clk", "atmel_mci.1", &mmc1_clk), CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.0", &spi0_clk), CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.1", &spi1_clk), CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tcb_clk), diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c index fe99206..617fbfc 100644 --- a/arch/arm/mach-at91/at91sam9263_devices.c +++ b/arch/arm/mach-at91/at91sam9263_devices.c @@ -354,6 +354,170 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {} #endif /* -------------------------------------------------------------------- + * MMC / SD + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static u64 mmc_dmamask = DMA_BIT_MASK(32); +static struct mci_platform_data mmc0_data, mmc1_data; + +static struct resource mmc0_resources[] = { + [0] = { + .start = AT91SAM9263_BASE_MCI0, + .end = AT91SAM9263_BASE_MCI0 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9263_ID_MCI0, + .end = AT91SAM9263_ID_MCI0, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91sam9263_mmc0_device = { + .name = "atmel_mci", + .id = 0, + .dev = { + .dma_mask = &mmc_dmamask, + .coherent_dma_mask = DMA_BIT_MASK(32), + .platform_data = &mmc0_data, + }, + .resource = mmc0_resources, + .num_resources = ARRAY_SIZE(mmc0_resources), +}; + +static struct resource mmc1_resources[] = { + [0] = { + .start = AT91SAM9263_BASE_MCI1, + .end = AT91SAM9263_BASE_MCI1 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9263_ID_MCI1, + .end = AT91SAM9263_ID_MCI1, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91sam9263_mmc1_device = { + .name = "atmel_mci", + .id = 1, + .dev = { + .dma_mask = &mmc_dmamask, + .coherent_dma_mask = DMA_BIT_MASK(32), + .platform_data = &mmc1_data, + }, + .resource = mmc1_resources, + .num_resources = ARRAY_SIZE(mmc1_resources), +}; + +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) +{ + unsigned int i; + unsigned int slot_count = 0; + + if (!data) + return; + + for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) { + + if (!data->slot[i].bus_width) + continue; + + /* input/irq */ + if (gpio_is_valid(data->slot[i].detect_pin)) { + at91_set_gpio_input(data->slot[i].detect_pin, + 1); + at91_set_deglitch(data->slot[i].detect_pin, + 1); + } + if (gpio_is_valid(data->slot[i].wp_pin)) + at91_set_gpio_input(data->slot[i].wp_pin, 1); + + if (mmc_id == 0) { /* MCI0 */ + switch (i) { + case 0: /* slot A */ + /* CMD */ + at91_set_A_periph(AT91_PIN_PA1, 1); + /* DAT0, maybe DAT1..DAT3 */ + at91_set_A_periph(AT91_PIN_PA0, 1); + if (data->slot[i].bus_width == 4) { + at91_set_A_periph(AT91_PIN_PA3, 1); + at91_set_A_periph(AT91_PIN_PA4, 1); + at91_set_A_periph(AT91_PIN_PA5, 1); + } + slot_count++; + break; + case 1: /* slot B */ + /* CMD */ + at91_set_A_periph(AT91_PIN_PA16, 1); + /* DAT0, maybe DAT1..DAT3 */ + at91_set_A_periph(AT91_PIN_PA17, 1); + if (data->slot[i].bus_width == 4) { + at91_set_A_periph(AT91_PIN_PA18, 1); + at91_set_A_periph(AT91_PIN_PA19, 1); + at91_set_A_periph(AT91_PIN_PA20, 1); + } + slot_count++; + break; + default: + printk(KERN_ERR + "AT91: SD/MMC slot %d not available\n", i); + break; + } + if (slot_count) { + /* CLK */ + at91_set_A_periph(AT91_PIN_PA12, 0); + + mmc0_data = *data; + platform_device_register(&at91sam9263_mmc0_device); + } + } else if (mmc_id == 1) { /* MCI1 */ + switch (i) { + case 0: /* slot A */ + /* CMD */ + at91_set_A_periph(AT91_PIN_PA7, 1); + /* DAT0, maybe DAT1..DAT3 */ + at91_set_A_periph(AT91_PIN_PA8, 1); + if (data->slot[i].bus_width == 4) { + at91_set_A_periph(AT91_PIN_PA9, 1); + at91_set_A_periph(AT91_PIN_PA10, 1); + at91_set_A_periph(AT91_PIN_PA11, 1); + } + slot_count++; + break; + case 1: /* slot B */ + /* CMD */ + at91_set_A_periph(AT91_PIN_PA21, 1); + /* DAT0, maybe DAT1..DAT3 */ + at91_set_A_periph(AT91_PIN_PA22, 1); + if (data->slot[i].bus_width == 4) { + at91_set_A_periph(AT91_PIN_PA23, 1); + at91_set_A_periph(AT91_PIN_PA24, 1); + at91_set_A_periph(AT91_PIN_PA25, 1); + } + slot_count++; + break; + default: + printk(KERN_ERR + "AT91: SD/MMC slot %d not available\n", i); + break; + } + if (slot_count) { + /* CLK */ + at91_set_A_periph(AT91_PIN_PA6, 0); + + mmc1_data = *data; + platform_device_register(&at91sam9263_mmc1_device); + } + } + } +} +#else +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {} +#endif + +/* -------------------------------------------------------------------- * Compact Flash (PCMCIA or IDE) * -------------------------------------------------------------------- */ diff --git a/arch/arm/mach-at91/at91sam9rl_devices.c b/arch/arm/mach-at91/at91sam9rl_devices.c index fe4ae22..83c5845 100644 --- a/arch/arm/mach-at91/at91sam9rl_devices.c +++ b/arch/arm/mach-at91/at91sam9rl_devices.c @@ -228,6 +228,76 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {} /* -------------------------------------------------------------------- + * MMC / SD + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static u64 mmc_dmamask = DMA_BIT_MASK(32); +static struct mci_platform_data mmc_data; + +static struct resource mmc_resources[] = { + [0] = { + .start = AT91SAM9RL_BASE_MCI, + .end = AT91SAM9RL_BASE_MCI + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9RL_ID_MCI, + .end = AT91SAM9RL_ID_MCI, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91sam9rl_mmc_device = { + .name = "atmel_mci", + .id = -1, + .dev = { + .dma_mask = &mmc_dmamask, + .coherent_dma_mask = DMA_BIT_MASK(32), + .platform_data = &mmc_data, + }, + .resource = mmc_resources, + .num_resources = ARRAY_SIZE(mmc_resources), +}; + +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) +{ + if (!data) + return; + + if (data->slot[0].bus_width) { + /* input/irq */ + if (gpio_is_valid(data->slot[0].detect_pin)) { + at91_set_gpio_input(data->slot[0].detect_pin, 1); + at91_set_deglitch(data->slot[0].detect_pin, 1); + } + if (gpio_is_valid(data->slot[0].wp_pin)) + at91_set_gpio_input(data->slot[0].wp_pin, 1); + + /* CLK */ + at91_set_A_periph(AT91_PIN_PA2, 0); + + /* CMD */ + at91_set_A_periph(AT91_PIN_PA1, 1); + + /* DAT0, maybe DAT1..DAT3 */ + at91_set_A_periph(AT91_PIN_PA0, 1); + if (data->slot[0].bus_width == 4) { + at91_set_A_periph(AT91_PIN_PA3, 1); + at91_set_A_periph(AT91_PIN_PA4, 1); + at91_set_A_periph(AT91_PIN_PA5, 1); + } + + mmc_data = *data; + platform_device_register(&at91sam9rl_mmc_device); + } +} +#else +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {} +#endif + + +/* -------------------------------------------------------------------- * NAND / SmartMedia * -------------------------------------------------------------------- */ diff --git a/arch/arm/mach-at91/board-afeb-9260v1.c b/arch/arm/mach-at91/board-afeb-9260v1.c index 161efba..1e294ba 100644 --- a/arch/arm/mach-at91/board-afeb-9260v1.c +++ b/arch/arm/mach-at91/board-afeb-9260v1.c @@ -148,6 +148,15 @@ static struct atmel_nand_data __initdata afeb9260_nand_data = { /* * MCI (SD/MMC) */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata afeb9260_mci0_data = { + .slot[1] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PC9, + .wp_pin = AT91_PIN_PC4, + }, +}; +#else static struct at91_mmc_data __initdata afeb9260_mmc_data = { .det_pin = AT91_PIN_PC9, .wp_pin = AT91_PIN_PC4, @@ -155,6 +164,7 @@ static struct at91_mmc_data __initdata afeb9260_mmc_data = { .wire4 = 1, .vcc_pin = -EINVAL, }; +#endif @@ -202,7 +212,11 @@ static void __init afeb9260_board_init(void) at91_set_B_periph(AT91_PIN_PA10, 0); /* ETX2 */ at91_set_B_periph(AT91_PIN_PA11, 0); /* ETX3 */ /* MMC */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &afeb9260_mci0_data); +#else at91_add_device_mmc(0, &afeb9260_mmc_data); +#endif /* I2C */ at91_add_device_i2c(afeb9260_i2c_devices, ARRAY_SIZE(afeb9260_i2c_devices)); diff --git a/arch/arm/mach-at91/board-carmeva.c b/arch/arm/mach-at91/board-carmeva.c index 59d9cf9..050b9d5 100644 --- a/arch/arm/mach-at91/board-carmeva.c +++ b/arch/arm/mach-at91/board-carmeva.c @@ -81,6 +81,15 @@ static struct at91_udc_data __initdata carmeva_udc_data = { // .vcc_pin = -EINVAL, // }; +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata carmeva_mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PB10, + .wp_pin = AT91_PIN_PC14, + }, +}; +#else static struct at91_mmc_data __initdata carmeva_mmc_data = { .slot_b = 0, .wire4 = 1, @@ -88,6 +97,7 @@ static struct at91_mmc_data __initdata carmeva_mmc_data = { .wp_pin = AT91_PIN_PC14, .vcc_pin = -EINVAL, }; +#endif static struct spi_board_info carmeva_spi_devices[] = { { /* DataFlash chip */ @@ -153,7 +163,11 @@ static void __init carmeva_board_init(void) /* Compact Flash */ // at91_add_device_cf(&carmeva_cf_data); /* MMC */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &carmeva_mci0_data); +#else at91_add_device_mmc(0, &carmeva_mmc_data); +#endif /* LEDs */ at91_gpio_leds(carmeva_leds, ARRAY_SIZE(carmeva_leds)); } diff --git a/arch/arm/mach-at91/board-cpu9krea.c b/arch/arm/mach-at91/board-cpu9krea.c index 5f3680e..9842297 100644 --- a/arch/arm/mach-at91/board-cpu9krea.c +++ b/arch/arm/mach-at91/board-cpu9krea.c @@ -339,6 +339,15 @@ static void __init cpu9krea_add_device_buttons(void) /* * MCI (SD/MMC) */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata cpu9krea_mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PA29, + .wp_pin = -EINVAL, + }, +}; +#else static struct at91_mmc_data __initdata cpu9krea_mmc_data = { .slot_b = 0, .wire4 = 1, @@ -346,6 +355,7 @@ static struct at91_mmc_data __initdata cpu9krea_mmc_data = { .wp_pin = -EINVAL, .vcc_pin = -EINVAL, }; +#endif static void __init cpu9krea_board_init(void) { @@ -362,7 +372,11 @@ static void __init cpu9krea_board_init(void) /* Ethernet */ at91_add_device_eth(&cpu9krea_macb_data); /* MMC */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &cpu9krea_mci0_data); +#else at91_add_device_mmc(0, &cpu9krea_mmc_data); +#endif /* I2C */ at91_add_device_i2c(cpu9krea_i2c_devices, ARRAY_SIZE(cpu9krea_i2c_devices)); diff --git a/arch/arm/mach-at91/board-cpuat91.c b/arch/arm/mach-at91/board-cpuat91.c index e094cc8..cb5dcbf 100644 --- a/arch/arm/mach-at91/board-cpuat91.c +++ b/arch/arm/mach-at91/board-cpuat91.c @@ -99,12 +99,22 @@ static struct at91_udc_data __initdata cpuat91_udc_data = { .pullup_pin = AT91_PIN_PC14, }; +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata cpuat91_mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PC2, + .wp_pin = -EINVAL, + }, +}; +#else static struct at91_mmc_data __initdata cpuat91_mmc_data = { .det_pin = AT91_PIN_PC2, .wire4 = 1, .wp_pin = -EINVAL, .vcc_pin = -EINVAL, }; +#endif static struct physmap_flash_data cpuat91_flash_data = { .width = 2, @@ -171,7 +181,11 @@ static void __init cpuat91_board_init(void) /* USB Device */ at91_add_device_udc(&cpuat91_udc_data); /* MMC */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &cpuat91_mci0_data); +#else at91_add_device_mmc(0, &cpuat91_mmc_data); +#endif /* I2C */ at91_add_device_i2c(NULL, 0); /* Platform devices */ diff --git a/arch/arm/mach-at91/board-csb337.c b/arch/arm/mach-at91/board-csb337.c index 1a1547b..36d65ef 100644 --- a/arch/arm/mach-at91/board-csb337.c +++ b/arch/arm/mach-at91/board-csb337.c @@ -95,6 +95,15 @@ static struct at91_cf_data __initdata csb337_cf_data = { .rst_pin = AT91_PIN_PD2, }; +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata csb337_mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PD5, + .wp_pin = AT91_PIN_PD6, + }, +}; +#else static struct at91_mmc_data __initdata csb337_mmc_data = { .det_pin = AT91_PIN_PD5, .slot_b = 0, @@ -102,6 +111,7 @@ static struct at91_mmc_data __initdata csb337_mmc_data = { .wp_pin = AT91_PIN_PD6, .vcc_pin = -EINVAL, }; +#endif static struct spi_board_info csb337_spi_devices[] = { { /* CAN controller */ @@ -244,7 +254,11 @@ static void __init csb337_board_init(void) /* SPI */ at91_add_device_spi(csb337_spi_devices, ARRAY_SIZE(csb337_spi_devices)); /* MMC */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &csb337_mci0_data); +#else at91_add_device_mmc(0, &csb337_mmc_data); +#endif /* NOR flash */ platform_device_register(&csb_flash); /* LEDs */ diff --git a/arch/arm/mach-at91/board-eb9200.c b/arch/arm/mach-at91/board-eb9200.c index d302ca3..f374ecc 100644 --- a/arch/arm/mach-at91/board-eb9200.c +++ b/arch/arm/mach-at91/board-eb9200.c @@ -83,6 +83,15 @@ static struct at91_cf_data __initdata eb9200_cf_data = { .rst_pin = AT91_PIN_PC5, }; +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata eb9200_mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = -EINVAL, + .wp_pin = -EINVAL, + }, +}; +#else static struct at91_mmc_data __initdata eb9200_mmc_data = { .slot_b = 0, .wire4 = 1, @@ -90,6 +99,7 @@ static struct at91_mmc_data __initdata eb9200_mmc_data = { .wp_pin = -EINVAL, .vcc_pin = -EINVAL, }; +#endif static struct i2c_board_info __initdata eb9200_i2c_devices[] = { { @@ -116,7 +126,11 @@ static void __init eb9200_board_init(void) at91_add_device_spi(NULL, 0); /* MMC */ /* only supports 1 or 4 bit interface, not wired through to SPI */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &eb9200_mci0_data); +#else at91_add_device_mmc(0, &eb9200_mmc_data); +#endif } MACHINE_START(ATEB9200, "Embest ATEB9200") diff --git a/arch/arm/mach-at91/board-ecbat91.c b/arch/arm/mach-at91/board-ecbat91.c index 69966ce..0f39fb3 100644 --- a/arch/arm/mach-at91/board-ecbat91.c +++ b/arch/arm/mach-at91/board-ecbat91.c @@ -75,6 +75,15 @@ static struct at91_usbh_data __initdata ecb_at91usbh_data = { .overcurrent_pin= {-EINVAL, -EINVAL}, }; +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata ecbat91_mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = -EINVAL, + .wp_pin = -EINVAL, + }, +}; +#else static struct at91_mmc_data __initdata ecb_at91mmc_data = { .slot_b = 0, .wire4 = 1, @@ -82,6 +91,7 @@ static struct at91_mmc_data __initdata ecb_at91mmc_data = { .wp_pin = -EINVAL, .vcc_pin = -EINVAL, }; +#endif #if defined(CONFIG_MTD_DATAFLASH) @@ -164,7 +174,11 @@ static void __init ecb_at91board_init(void) at91_add_device_i2c(NULL, 0); /* MMC */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &ecbat91_mci0_data); +#else at91_add_device_mmc(0, &ecb_at91mmc_data); +#endif /* SPI */ at91_add_device_spi(ecb_at91spi_devices, ARRAY_SIZE(ecb_at91spi_devices)); diff --git a/arch/arm/mach-at91/board-eco920.c b/arch/arm/mach-at91/board-eco920.c index f23aabe..932bebd 100644 --- a/arch/arm/mach-at91/board-eco920.c +++ b/arch/arm/mach-at91/board-eco920.c @@ -64,6 +64,15 @@ static struct at91_udc_data __initdata eco920_udc_data = { .pullup_pin = AT91_PIN_PB13, }; +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata eco920_mci0_data = { + .slot[0] = { + .bus_width = 1, + .detect_pin = -EINVAL, + .wp_pin = -EINVAL, + }, +}; +#else static struct at91_mmc_data __initdata eco920_mmc_data = { .slot_b = 0, .wire4 = 0, @@ -71,6 +80,7 @@ static struct at91_mmc_data __initdata eco920_mmc_data = { .wp_pin = -EINVAL, .vcc_pin = -EINVAL, }; +#endif static struct physmap_flash_data eco920_flash_data = { .width = 2, @@ -108,7 +118,11 @@ static void __init eco920_board_init(void) at91_add_device_usbh(&eco920_usbh_data); at91_add_device_udc(&eco920_udc_data); +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &eco920_mci0_data); +#else at91_add_device_mmc(0, &eco920_mmc_data); +#endif platform_device_register(&eco920_flash); at91_ramc_write(0, AT91_SMC_CSR(7), AT91_SMC_RWHOLD_(1) diff --git a/arch/arm/mach-at91/board-flexibity.c b/arch/arm/mach-at91/board-flexibity.c index 1815152..6632a80 100644 --- a/arch/arm/mach-at91/board-flexibity.c +++ b/arch/arm/mach-at91/board-flexibity.c @@ -80,6 +80,15 @@ static struct spi_board_info flexibity_spi_devices[] = { }; /* MCI (SD/MMC) */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata flexibity_mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PC9, + .wp_pin = AT91_PIN_PC4, + }, +}; +#else static struct at91_mmc_data __initdata flexibity_mmc_data = { .slot_b = 0, .wire4 = 1, @@ -87,6 +96,7 @@ static struct at91_mmc_data __initdata flexibity_mmc_data = { .wp_pin = AT91_PIN_PC4, .vcc_pin = -EINVAL, }; +#endif /* LEDs */ static struct gpio_led flexibity_leds[] = { @@ -155,7 +165,11 @@ static void __init flexibity_board_init(void) at91_add_device_spi(flexibity_spi_devices, ARRAY_SIZE(flexibity_spi_devices)); /* MMC */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &flexibity_mci0_data); +#else at91_add_device_mmc(0, &flexibity_mmc_data); +#endif /* LEDs */ at91_gpio_leds(flexibity_leds, ARRAY_SIZE(flexibity_leds)); } diff --git a/arch/arm/mach-at91/board-foxg20.c b/arch/arm/mach-at91/board-foxg20.c index caf017f..6cda303 100644 --- a/arch/arm/mach-at91/board-foxg20.c +++ b/arch/arm/mach-at91/board-foxg20.c @@ -123,7 +123,7 @@ static struct at91_udc_data __initdata foxg20_udc_data = { * SPI devices. */ static struct spi_board_info foxg20_spi_devices[] = { -#if !defined(CONFIG_MMC_AT91) +#if !defined(CONFIG_MMC_AT91) && !defined(CONFIG_MMC_ATMELMCI) { .modalias = "mtd_dataflash", .chip_select = 1, @@ -146,6 +146,7 @@ static struct macb_platform_data __initdata foxg20_macb_data = { * MCI (SD/MMC) * det_pin, wp_pin and vcc_pin are not connected */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) static struct at91_mmc_data __initdata foxg20_mmc_data = { .slot_b = 1, .wire4 = 1, @@ -153,6 +154,15 @@ static struct at91_mmc_data __initdata foxg20_mmc_data = { .wp_pin = -EINVAL, .vcc_pin = -EINVAL, }; +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata foxg20_mci0_data = { + .slot[1] = { + .bus_width = 4, + .detect_pin = -EINVAL, + .wp_pin = -EINVAL, + }, +}; +#endif /* @@ -251,7 +261,11 @@ static void __init foxg20_board_init(void) /* Ethernet */ at91_add_device_eth(&foxg20_macb_data); /* MMC */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) at91_add_device_mmc(0, &foxg20_mmc_data); +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &foxg20_mci0_data); +#endif /* I2C */ at91_add_device_i2c(foxg20_i2c_devices, ARRAY_SIZE(foxg20_i2c_devices)); /* LEDs */ diff --git a/arch/arm/mach-at91/board-kb9202.c b/arch/arm/mach-at91/board-kb9202.c index 59b92aa..e31ec8e 100644 --- a/arch/arm/mach-at91/board-kb9202.c +++ b/arch/arm/mach-at91/board-kb9202.c @@ -86,6 +86,15 @@ static struct at91_udc_data __initdata kb9202_udc_data = { .pullup_pin = AT91_PIN_PB22, }; +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata kb9202_mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PB2, + .wp_pin = -EINVAL, + }, +}; +#else static struct at91_mmc_data __initdata kb9202_mmc_data = { .det_pin = AT91_PIN_PB2, .slot_b = 0, @@ -93,6 +102,7 @@ static struct at91_mmc_data __initdata kb9202_mmc_data = { .wp_pin = -EINVAL, .vcc_pin = -EINVAL, }; +#endif static struct mtd_partition __initdata kb9202_nand_partition[] = { { @@ -124,7 +134,11 @@ static void __init kb9202_board_init(void) /* USB Device */ at91_add_device_udc(&kb9202_udc_data); /* MMC */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &kb9202_mci0_data); +#else at91_add_device_mmc(0, &kb9202_mmc_data); +#endif /* I2C */ at91_add_device_i2c(NULL, 0); /* SPI */ diff --git a/arch/arm/mach-at91/board-neocore926.c b/arch/arm/mach-at91/board-neocore926.c index 57d5f6a..849b938 100644 --- a/arch/arm/mach-at91/board-neocore926.c +++ b/arch/arm/mach-at91/board-neocore926.c @@ -146,12 +146,22 @@ static struct spi_board_info neocore926_spi_devices[] = { /* * MCI (SD/MMC) */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata neocore926_mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PE18, + .wp_pin = AT91_PIN_PE19, + }, +}; +#else static struct at91_mmc_data __initdata neocore926_mmc_data = { .wire4 = 1, .det_pin = AT91_PIN_PE18, .wp_pin = AT91_PIN_PE19, .vcc_pin = -EINVAL, }; +#endif /* @@ -357,7 +367,11 @@ static void __init neocore926_board_init(void) neocore926_add_device_ts(); /* MMC */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &neocore926_mci0_data); +#else at91_add_device_mmc(1, &neocore926_mmc_data); +#endif /* Ethernet */ at91_add_device_eth(&neocore926_macb_data); diff --git a/arch/arm/mach-at91/board-picotux200.c b/arch/arm/mach-at91/board-picotux200.c index 59e35dd..a8cb032 100644 --- a/arch/arm/mach-at91/board-picotux200.c +++ b/arch/arm/mach-at91/board-picotux200.c @@ -72,6 +72,15 @@ static struct at91_usbh_data __initdata picotux200_usbh_data = { .overcurrent_pin= {-EINVAL, -EINVAL}, }; +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata picotux200_mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PB27, + .wp_pin = AT91_PIN_PA17, + }, +}; +#else static struct at91_mmc_data __initdata picotux200_mmc_data = { .det_pin = AT91_PIN_PB27, .slot_b = 0, @@ -79,6 +88,7 @@ static struct at91_mmc_data __initdata picotux200_mmc_data = { .wp_pin = AT91_PIN_PA17, .vcc_pin = -EINVAL, }; +#endif #define PICOTUX200_FLASH_BASE AT91_CHIPSELECT_0 #define PICOTUX200_FLASH_SIZE SZ_4M @@ -115,7 +125,11 @@ static void __init picotux200_board_init(void) at91_add_device_i2c(NULL, 0); /* MMC */ at91_set_gpio_output(AT91_PIN_PB22, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &picotux200_mci0_data); +#else at91_add_device_mmc(0, &picotux200_mmc_data); +#endif /* NOR Flash */ platform_device_register(&picotux200_flash); } diff --git a/arch/arm/mach-at91/board-qil-a9260.c b/arch/arm/mach-at91/board-qil-a9260.c index b6ed5ed..2a49993 100644 --- a/arch/arm/mach-at91/board-qil-a9260.c +++ b/arch/arm/mach-at91/board-qil-a9260.c @@ -173,6 +173,15 @@ static void __init ek_add_device_nand(void) /* * MCI (SD/MMC) */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata ek_mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = -EINVAL, + .wp_pin = -EINVAL, + }, +}; +#else static struct at91_mmc_data __initdata ek_mmc_data = { .slot_b = 0, .wire4 = 1, @@ -180,6 +189,7 @@ static struct at91_mmc_data __initdata ek_mmc_data = { .wp_pin = -EINVAL, .vcc_pin = -EINVAL, }; +#endif /* * GPIO Buttons @@ -249,7 +259,11 @@ static void __init ek_board_init(void) /* Ethernet */ at91_add_device_eth(&ek_macb_data); /* MMC */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &ek_mci0_data); +#else at91_add_device_mmc(0, &ek_mmc_data); +#endif /* Push Buttons */ ek_add_device_buttons(); /* LEDs */ diff --git a/arch/arm/mach-at91/board-rm9200dk.c b/arch/arm/mach-at91/board-rm9200dk.c index 01332aa..b6128fb 100644 --- a/arch/arm/mach-at91/board-rm9200dk.c +++ b/arch/arm/mach-at91/board-rm9200dk.c @@ -90,6 +90,15 @@ static struct at91_cf_data __initdata dk_cf_data = { }; #ifndef CONFIG_MTD_AT91_DATAFLASH_CARD +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata dk_mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = -EINVAL, + .wp_pin = -EINVAL, + }, +}; +#else static struct at91_mmc_data __initdata dk_mmc_data = { .slot_b = 0, .wire4 = 1, @@ -98,6 +107,7 @@ static struct at91_mmc_data __initdata dk_mmc_data = { .vcc_pin = -EINVAL, }; #endif +#endif static struct spi_board_info dk_spi_devices[] = { { /* DataFlash chip */ @@ -211,8 +221,12 @@ static void __init dk_board_init(void) #else /* MMC */ at91_set_gpio_output(AT91_PIN_PB7, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &dk_mci0_data); +#else at91_add_device_mmc(0, &dk_mmc_data); #endif +#endif /* NAND */ at91_add_device_nand(&dk_nand_data); /* NOR Flash */ diff --git a/arch/arm/mach-at91/board-rm9200ek.c b/arch/arm/mach-at91/board-rm9200ek.c index b2e4fe2..7177aac 100644 --- a/arch/arm/mach-at91/board-rm9200ek.c +++ b/arch/arm/mach-at91/board-rm9200ek.c @@ -83,6 +83,7 @@ static struct at91_udc_data __initdata ek_udc_data = { }; #ifndef CONFIG_MTD_AT91_DATAFLASH_CARD +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) static struct at91_mmc_data __initdata ek_mmc_data = { .det_pin = AT91_PIN_PB27, .slot_b = 0, @@ -90,6 +91,15 @@ static struct at91_mmc_data __initdata ek_mmc_data = { .wp_pin = AT91_PIN_PA17, .vcc_pin = -EINVAL, }; +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata ek_mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PB27, + .wp_pin = AT91_PIN_PA17, + } +}; +#endif #endif static struct spi_board_info ek_spi_devices[] = { @@ -180,7 +190,11 @@ static void __init ek_board_init(void) #else /* MMC */ at91_set_gpio_output(AT91_PIN_PB22, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) at91_add_device_mmc(0, &ek_mmc_data); +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &ek_mci0_data); +#endif #endif /* NOR Flash */ platform_device_register(&ek_flash); diff --git a/arch/arm/mach-at91/board-rsi-ews.c b/arch/arm/mach-at91/board-rsi-ews.c index af0750f..373537a 100644 --- a/arch/arm/mach-at91/board-rsi-ews.c +++ b/arch/arm/mach-at91/board-rsi-ews.c @@ -77,12 +77,22 @@ static struct at91_usbh_data rsi_ews_usbh_data __initdata = { /* * SD/MC */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata rsi_ews_mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PB27, + .wp_pin = AT91_PIN_PB29, + }, +}; +#else static struct at91_mmc_data rsi_ews_mmc_data __initdata = { .slot_b = 0, .wire4 = 1, .det_pin = AT91_PIN_PB27, .wp_pin = AT91_PIN_PB29, }; +#endif /* * I2C @@ -218,7 +228,11 @@ static void __init rsi_ews_board_init(void) at91_add_device_spi(rsi_ews_spi_devices, ARRAY_SIZE(rsi_ews_spi_devices)); /* MMC */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &rsi_ews_mci0_data); +#else at91_add_device_mmc(0, &rsi_ews_mmc_data); +#endif /* NOR Flash */ platform_device_register(&rsiews_nor_flash); /* LEDs */ diff --git a/arch/arm/mach-at91/board-sam9-l9260.c b/arch/arm/mach-at91/board-sam9-l9260.c index e8b116b..7562011 100644 --- a/arch/arm/mach-at91/board-sam9-l9260.c +++ b/arch/arm/mach-at91/board-sam9-l9260.c @@ -89,7 +89,7 @@ static struct at91_udc_data __initdata ek_udc_data = { * SPI devices. */ static struct spi_board_info ek_spi_devices[] = { -#if !defined(CONFIG_MMC_AT91) +#if !defined(CONFIG_MMC_AT91) && !defined(CONFIG_MMC_ATMELMCI) { /* DataFlash chip */ .modalias = "mtd_dataflash", .chip_select = 1, @@ -174,6 +174,15 @@ static void __init ek_add_device_nand(void) /* * MCI (SD/MMC) */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata ek_mci0_data = { + .slot[1] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PC8, + .wp_pin = AT91_PIN_PC4, + }, +}; +#else static struct at91_mmc_data __initdata ek_mmc_data = { .slot_b = 1, .wire4 = 1, @@ -181,6 +190,7 @@ static struct at91_mmc_data __initdata ek_mmc_data = { .wp_pin = AT91_PIN_PC4, .vcc_pin = -EINVAL, }; +#endif static void __init ek_board_init(void) { @@ -197,7 +207,11 @@ static void __init ek_board_init(void) /* Ethernet */ at91_add_device_eth(&ek_macb_data); /* MMC */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &ek_mci0_data); +#else at91_add_device_mmc(0, &ek_mmc_data); +#endif /* I2C */ at91_add_device_i2c(NULL, 0); } diff --git a/arch/arm/mach-at91/board-sam9260ek.c b/arch/arm/mach-at91/board-sam9260ek.c index d5aec55..b39009e 100644 --- a/arch/arm/mach-at91/board-sam9260ek.c +++ b/arch/arm/mach-at91/board-sam9260ek.c @@ -121,7 +121,7 @@ static void __init at73c213_set_clk(struct at73c213_board_info *info) {} * SPI devices. */ static struct spi_board_info ek_spi_devices[] = { -#if !defined(CONFIG_MMC_AT91) +#if !defined(CONFIG_MMC_AT91) && !defined(CONFIG_MMC_ATMELMCI) { /* DataFlash chip */ .modalias = "mtd_dataflash", .chip_select = 1, @@ -224,6 +224,15 @@ static void __init ek_add_device_nand(void) /* * MCI (SD/MMC) */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata ek_mci0_data = { + .slot[1] = { + .bus_width = 4, + .detect_pin = -EINVAL, + .wp_pin = -EINVAL, + }, +}; +#else static struct at91_mmc_data __initdata ek_mmc_data = { .slot_b = 1, .wire4 = 1, @@ -231,6 +240,7 @@ static struct at91_mmc_data __initdata ek_mmc_data = { .wp_pin = -EINVAL, .vcc_pin = -EINVAL, }; +#endif /* @@ -332,7 +342,11 @@ static void __init ek_board_init(void) /* Ethernet */ at91_add_device_eth(&ek_macb_data); /* MMC */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &ek_mci0_data); +#else at91_add_device_mmc(0, &ek_mmc_data); +#endif /* I2C */ at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices)); /* SSC (to AT73C213) */ diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c index 065fed3..797dd7c 100644 --- a/arch/arm/mach-at91/board-sam9261ek.c +++ b/arch/arm/mach-at91/board-sam9261ek.c @@ -344,6 +344,7 @@ static struct spi_board_info ek_spi_devices[] = { #else /* CONFIG_SPI_ATMEL_* */ /* spi0 and mmc/sd share the same PIO pins: cannot be used at the same time */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) /* * MCI (SD/MMC) * det_pin, wp_pin and vcc_pin are not connected @@ -354,6 +355,15 @@ static struct at91_mmc_data __initdata ek_mmc_data = { .wp_pin = -EINVAL, .vcc_pin = -EINVAL, }; +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = -EINVAL, + .wp_pin = -EINVAL, + }, +}; +#endif #endif /* CONFIG_SPI_ATMEL_* */ @@ -601,7 +611,11 @@ static void __init ek_board_init(void) at91_add_device_ssc(AT91SAM9261_ID_SSC1, ATMEL_SSC_TX); #else /* MMC */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) at91_add_device_mmc(0, &ek_mmc_data); +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &mci0_data); +#endif #endif /* LCD Controller */ at91_add_device_lcdc(&ek_lcdc_data); diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c index 2ffe50f..419c57a 100644 --- a/arch/arm/mach-at91/board-sam9263ek.c +++ b/arch/arm/mach-at91/board-sam9263ek.c @@ -149,12 +149,22 @@ static struct spi_board_info ek_spi_devices[] = { /* * MCI (SD/MMC) */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata mci1_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PE18, + .wp_pin = AT91_PIN_PE19, + }, +}; +#else static struct at91_mmc_data __initdata ek_mmc_data = { .wire4 = 1, .det_pin = AT91_PIN_PE18, .wp_pin = AT91_PIN_PE19, .vcc_pin = -EINVAL, }; +#endif /* @@ -423,7 +433,11 @@ static void __init ek_board_init(void) /* Touchscreen */ ek_add_device_ts(); /* MMC */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(1, &mci1_data); +#else at91_add_device_mmc(1, &ek_mmc_data); +#endif /* Ethernet */ at91_add_device_eth(&ek_macb_data); /* NAND */ diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c index b109ce2..bb06521 100644 --- a/arch/arm/mach-at91/board-sam9rlek.c +++ b/arch/arm/mach-at91/board-sam9rlek.c @@ -64,12 +64,22 @@ static struct usba_platform_data __initdata ek_usba_udc_data = { /* * MCI (SD/MMC) */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) static struct at91_mmc_data __initdata ek_mmc_data = { .wire4 = 1, .det_pin = AT91_PIN_PA15, .wp_pin = -EINVAL, .vcc_pin = -EINVAL, }; +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PA15, + .wp_pin = -EINVAL, + }, +}; +#endif /* @@ -306,7 +316,11 @@ static void __init ek_board_init(void) /* SPI */ at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); /* MMC */ +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) at91_add_device_mmc(0, &ek_mmc_data); +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &mci0_data); +#endif /* LCD Controller */ at91_add_device_lcdc(&ek_lcdc_data); /* AC97 */ diff --git a/arch/arm/mach-at91/board-usb-a926x.c b/arch/arm/mach-at91/board-usb-a926x.c index b7483a3..879e34e 100644 --- a/arch/arm/mach-at91/board-usb-a926x.c +++ b/arch/arm/mach-at91/board-usb-a926x.c @@ -114,7 +114,7 @@ static struct mmc_spi_platform_data at91_mmc_spi_pdata = { * SPI devices. */ static struct spi_board_info usb_a9263_spi_devices[] = { -#if !defined(CONFIG_MMC_AT91) +#if !defined(CONFIG_MMC_AT91) && !defined(CONFIG_MMC_ATMELMCI) { /* DataFlash chip */ .modalias = "mtd_dataflash", .chip_select = 0, diff --git a/arch/arm/mach-at91/board-yl-9200.c b/arch/arm/mach-at91/board-yl-9200.c index 38dd279..3d3b8a6 100644 --- a/arch/arm/mach-at91/board-yl-9200.c +++ b/arch/arm/mach-at91/board-yl-9200.c @@ -138,12 +138,22 @@ static struct at91_udc_data __initdata yl9200_udc_data = { /* * MMC */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata yl9200_mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PB9, + .wp_pin = -EINVAL, + }, +}; +#else static struct at91_mmc_data __initdata yl9200_mmc_data = { .det_pin = AT91_PIN_PB9, .wire4 = 1, .wp_pin = -EINVAL, .vcc_pin = -EINVAL, }; +#endif /* * NAND Flash @@ -571,7 +581,11 @@ static void __init yl9200_board_init(void) /* I2C */ at91_add_device_i2c(yl9200_i2c_devices, ARRAY_SIZE(yl9200_i2c_devices)); /* MMC */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &yl9200_mci0_data); +#else at91_add_device_mmc(0, &yl9200_mmc_data); +#endif /* NAND */ at91_add_device_nand(&yl9200_nand_data); /* NOR Flash */ -- 1.7.5.4 ^ permalink raw reply related [flat|nested] 28+ messages in thread
* Re: [PATCH v2] ARM: at91: add atmel-mci support for chips and boards which can use it 2012-05-21 10:23 ` ludovic.desroches at atmel.com @ 2012-05-21 10:31 ` ludovic.desroches -1 siblings, 0 replies; 28+ messages in thread From: ludovic.desroches @ 2012-05-21 10:31 UTC (permalink / raw) To: ludovic.desroches; +Cc: nicolas.ferre, plagnioj, linux-mmc, linux-arm-kernel Le 05/21/2012 12:23 PM, ludovic.desroches@atmel.com a écrit : > From: Ludovic Desroches<ludovic.desroches@atmel.com> > > Since atmel-mci driver supports all atmel mci version excepted the rm9200 one, > use it instead of at91_mci driver. Sorry commit message is wrong. Since atmel-mci driver supports all atmel mci versions, use it instead of at91_mci driver. > > Signed-off-by: Ludovic Desroches<ludovic.desroches@atmel.com> > --- > V2: add several boards I missed > > arch/arm/mach-at91/at91rm9200_devices.c | 99 ++++++++++++++++++ > arch/arm/mach-at91/at91sam9261_devices.c | 67 ++++++++++++ > arch/arm/mach-at91/at91sam9263.c | 2 + > arch/arm/mach-at91/at91sam9263_devices.c | 164 ++++++++++++++++++++++++++++++ > arch/arm/mach-at91/at91sam9rl_devices.c | 70 +++++++++++++ > arch/arm/mach-at91/board-afeb-9260v1.c | 14 +++ > arch/arm/mach-at91/board-carmeva.c | 14 +++ > arch/arm/mach-at91/board-cpu9krea.c | 14 +++ > arch/arm/mach-at91/board-cpuat91.c | 14 +++ > arch/arm/mach-at91/board-csb337.c | 14 +++ > arch/arm/mach-at91/board-eb9200.c | 14 +++ > arch/arm/mach-at91/board-ecbat91.c | 14 +++ > arch/arm/mach-at91/board-eco920.c | 14 +++ > arch/arm/mach-at91/board-flexibity.c | 14 +++ > arch/arm/mach-at91/board-foxg20.c | 16 +++- > arch/arm/mach-at91/board-kb9202.c | 14 +++ > arch/arm/mach-at91/board-neocore926.c | 14 +++ > arch/arm/mach-at91/board-picotux200.c | 14 +++ > arch/arm/mach-at91/board-qil-a9260.c | 14 +++ > arch/arm/mach-at91/board-rm9200dk.c | 14 +++ > arch/arm/mach-at91/board-rm9200ek.c | 14 +++ > arch/arm/mach-at91/board-rsi-ews.c | 14 +++ > arch/arm/mach-at91/board-sam9-l9260.c | 16 +++- > arch/arm/mach-at91/board-sam9260ek.c | 16 +++- > arch/arm/mach-at91/board-sam9261ek.c | 14 +++ > arch/arm/mach-at91/board-sam9263ek.c | 14 +++ > arch/arm/mach-at91/board-sam9rlek.c | 14 +++ > arch/arm/mach-at91/board-usb-a926x.c | 2 +- > arch/arm/mach-at91/board-yl-9200.c | 14 +++ > 29 files changed, 728 insertions(+), 4 deletions(-) > > diff --git a/arch/arm/mach-at91/at91rm9200_devices.c b/arch/arm/mach-at91/at91rm9200_devices.c > index 05774e5..2c13783 100644 > --- a/arch/arm/mach-at91/at91rm9200_devices.c > +++ b/arch/arm/mach-at91/at91rm9200_devices.c > @@ -374,6 +374,105 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {} > > > /* -------------------------------------------------------------------- > + * MMC / SD > + * -------------------------------------------------------------------- */ > + > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static u64 mmc_dmamask = DMA_BIT_MASK(32); > +static struct mci_platform_data mmc_data; > + > +static struct resource mmc_resources[] = { > + [0] = { > + .start = AT91RM9200_BASE_MCI, > + .end = AT91RM9200_BASE_MCI + SZ_16K - 1, > + .flags = IORESOURCE_MEM, > + }, > + [1] = { > + .start = AT91RM9200_ID_MCI, > + .end = AT91RM9200_ID_MCI, > + .flags = IORESOURCE_IRQ, > + }, > +}; > + > +static struct platform_device at91rm9200_mmc_device = { > + .name = "atmel_mci", > + .id = -1, > + .dev = { > + .dma_mask =&mmc_dmamask, > + .coherent_dma_mask = DMA_BIT_MASK(32), > + .platform_data =&mmc_data, > + }, > + .resource = mmc_resources, > + .num_resources = ARRAY_SIZE(mmc_resources), > +}; > + > +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) > +{ > + unsigned int i; > + unsigned int slot_count = 0; > + > + if (!data) > + return; > + > + for (i = 0; i< ATMCI_MAX_NR_SLOTS; i++) { > + > + if (!data->slot[i].bus_width) > + continue; > + > + /* input/irq */ > + if (gpio_is_valid(data->slot[i].detect_pin)) { > + at91_set_gpio_input(data->slot[i].detect_pin, 1); > + at91_set_deglitch(data->slot[i].detect_pin, 1); > + } > + if (gpio_is_valid(data->slot[i].wp_pin)) > + at91_set_gpio_input(data->slot[i].wp_pin, 1); > + > + switch (i) { > + case 0: /* slot A */ > + /* CMD */ > + at91_set_A_periph(AT91_PIN_PA28, 1); > + /* DAT0, maybe DAT1..DAT3 */ > + at91_set_A_periph(AT91_PIN_PA29, 1); > + if (data->slot[i].bus_width == 4) { > + at91_set_B_periph(AT91_PIN_PB3, 1); > + at91_set_B_periph(AT91_PIN_PB4, 1); > + at91_set_B_periph(AT91_PIN_PB5, 1); > + } > + slot_count++; > + break; > + case 1: /* slot B */ > + /* CMD */ > + at91_set_B_periph(AT91_PIN_PA8, 1); > + /* DAT0, maybe DAT1..DAT3 */ > + at91_set_B_periph(AT91_PIN_PA9, 1); > + if (data->slot[i].bus_width == 4) { > + at91_set_B_periph(AT91_PIN_PA10, 1); > + at91_set_B_periph(AT91_PIN_PA11, 1); > + at91_set_B_periph(AT91_PIN_PA12, 1); > + } > + slot_count++; > + break; > + default: > + printk(KERN_ERR > + "AT91: SD/MMC slot %d not available\n", i); > + break; > + } > + if (slot_count) { > + /* CLK */ > + at91_set_A_periph(AT91_PIN_PA27, 0); > + > + mmc_data = *data; > + platform_device_register(&at91rm9200_mmc_device); > + } > + } > + > +} > +#else > +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {} > +#endif > + > + > +/* -------------------------------------------------------------------- > * NAND / SmartMedia > * -------------------------------------------------------------------- */ > > diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c > index 4db961a..0817854 100644 > --- a/arch/arm/mach-at91/at91sam9261_devices.c > +++ b/arch/arm/mach-at91/at91sam9261_devices.c > @@ -202,7 +202,74 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) > void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {} > #endif > > +/* -------------------------------------------------------------------- > + * MMC / SD Slot for Atmel MCI Driver > + * -------------------------------------------------------------------- */ > + > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static u64 mmc_dmamask = DMA_BIT_MASK(32); > +static struct mci_platform_data mmc_data; > + > +static struct resource mmc_resources[] = { > + [0] = { > + .start = AT91SAM9261_BASE_MCI, > + .end = AT91SAM9261_BASE_MCI + SZ_16K - 1, > + .flags = IORESOURCE_MEM, > + }, > + [1] = { > + .start = AT91SAM9261_ID_MCI, > + .end = AT91SAM9261_ID_MCI, > + .flags = IORESOURCE_IRQ, > + }, > +}; > + > +static struct platform_device at91sam9261_mmc_device = { > + .name = "atmel_mci", > + .id = -1, > + .dev = { > + .dma_mask =&mmc_dmamask, > + .coherent_dma_mask = DMA_BIT_MASK(32), > + .platform_data =&mmc_data, > + }, > + .resource = mmc_resources, > + .num_resources = ARRAY_SIZE(mmc_resources), > +}; > + > +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) > +{ > + if (!data) > + return; > > + if (data->slot[0].bus_width) { > + /* input/irq */ > + if (gpio_is_valid(data->slot[0].detect_pin)) { > + at91_set_gpio_input(data->slot[0].detect_pin, 1); > + at91_set_deglitch(data->slot[0].detect_pin, 1); > + } > + if (gpio_is_valid(data->slot[0].wp_pin)) > + at91_set_gpio_input(data->slot[0].wp_pin, 1); > + > + /* CLK */ > + at91_set_B_periph(AT91_PIN_PA2, 0); > + > + /* CMD */ > + at91_set_B_periph(AT91_PIN_PA1, 1); > + > + /* DAT0, maybe DAT1..DAT3 */ > + at91_set_B_periph(AT91_PIN_PA0, 1); > + if (data->slot[0].bus_width == 4) { > + at91_set_B_periph(AT91_PIN_PA4, 1); > + at91_set_B_periph(AT91_PIN_PA5, 1); > + at91_set_B_periph(AT91_PIN_PA6, 1); > + } > + > + mmc_data = *data; > + platform_device_register(&at91sam9261_mmc_device); > + } > +} > +#else > +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {} > +#endif > /* -------------------------------------------------------------------- > * NAND / SmartMedia > * -------------------------------------------------------------------- */ > diff --git a/arch/arm/mach-at91/at91sam9263.c b/arch/arm/mach-at91/at91sam9263.c > index ef301be..053e47a 100644 > --- a/arch/arm/mach-at91/at91sam9263.c > +++ b/arch/arm/mach-at91/at91sam9263.c > @@ -189,6 +189,8 @@ static struct clk_lookup periph_clocks_lookups[] = { > CLKDEV_CON_DEV_ID("pclk", "ssc.1",&ssc1_clk), > CLKDEV_CON_DEV_ID("mci_clk", "at91_mci.0",&mmc0_clk), > CLKDEV_CON_DEV_ID("mci_clk", "at91_mci.1",&mmc1_clk), > + CLKDEV_CON_DEV_ID("mci_clk", "atmel_mci.0",&mmc0_clk), > + CLKDEV_CON_DEV_ID("mci_clk", "atmel_mci.1",&mmc1_clk), > CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.0",&spi0_clk), > CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.1",&spi1_clk), > CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0",&tcb_clk), > diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c > index fe99206..617fbfc 100644 > --- a/arch/arm/mach-at91/at91sam9263_devices.c > +++ b/arch/arm/mach-at91/at91sam9263_devices.c > @@ -354,6 +354,170 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {} > #endif > > /* -------------------------------------------------------------------- > + * MMC / SD > + * -------------------------------------------------------------------- */ > + > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static u64 mmc_dmamask = DMA_BIT_MASK(32); > +static struct mci_platform_data mmc0_data, mmc1_data; > + > +static struct resource mmc0_resources[] = { > + [0] = { > + .start = AT91SAM9263_BASE_MCI0, > + .end = AT91SAM9263_BASE_MCI0 + SZ_16K - 1, > + .flags = IORESOURCE_MEM, > + }, > + [1] = { > + .start = AT91SAM9263_ID_MCI0, > + .end = AT91SAM9263_ID_MCI0, > + .flags = IORESOURCE_IRQ, > + }, > +}; > + > +static struct platform_device at91sam9263_mmc0_device = { > + .name = "atmel_mci", > + .id = 0, > + .dev = { > + .dma_mask =&mmc_dmamask, > + .coherent_dma_mask = DMA_BIT_MASK(32), > + .platform_data =&mmc0_data, > + }, > + .resource = mmc0_resources, > + .num_resources = ARRAY_SIZE(mmc0_resources), > +}; > + > +static struct resource mmc1_resources[] = { > + [0] = { > + .start = AT91SAM9263_BASE_MCI1, > + .end = AT91SAM9263_BASE_MCI1 + SZ_16K - 1, > + .flags = IORESOURCE_MEM, > + }, > + [1] = { > + .start = AT91SAM9263_ID_MCI1, > + .end = AT91SAM9263_ID_MCI1, > + .flags = IORESOURCE_IRQ, > + }, > +}; > + > +static struct platform_device at91sam9263_mmc1_device = { > + .name = "atmel_mci", > + .id = 1, > + .dev = { > + .dma_mask =&mmc_dmamask, > + .coherent_dma_mask = DMA_BIT_MASK(32), > + .platform_data =&mmc1_data, > + }, > + .resource = mmc1_resources, > + .num_resources = ARRAY_SIZE(mmc1_resources), > +}; > + > +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) > +{ > + unsigned int i; > + unsigned int slot_count = 0; > + > + if (!data) > + return; > + > + for (i = 0; i< ATMCI_MAX_NR_SLOTS; i++) { > + > + if (!data->slot[i].bus_width) > + continue; > + > + /* input/irq */ > + if (gpio_is_valid(data->slot[i].detect_pin)) { > + at91_set_gpio_input(data->slot[i].detect_pin, > + 1); > + at91_set_deglitch(data->slot[i].detect_pin, > + 1); > + } > + if (gpio_is_valid(data->slot[i].wp_pin)) > + at91_set_gpio_input(data->slot[i].wp_pin, 1); > + > + if (mmc_id == 0) { /* MCI0 */ > + switch (i) { > + case 0: /* slot A */ > + /* CMD */ > + at91_set_A_periph(AT91_PIN_PA1, 1); > + /* DAT0, maybe DAT1..DAT3 */ > + at91_set_A_periph(AT91_PIN_PA0, 1); > + if (data->slot[i].bus_width == 4) { > + at91_set_A_periph(AT91_PIN_PA3, 1); > + at91_set_A_periph(AT91_PIN_PA4, 1); > + at91_set_A_periph(AT91_PIN_PA5, 1); > + } > + slot_count++; > + break; > + case 1: /* slot B */ > + /* CMD */ > + at91_set_A_periph(AT91_PIN_PA16, 1); > + /* DAT0, maybe DAT1..DAT3 */ > + at91_set_A_periph(AT91_PIN_PA17, 1); > + if (data->slot[i].bus_width == 4) { > + at91_set_A_periph(AT91_PIN_PA18, 1); > + at91_set_A_periph(AT91_PIN_PA19, 1); > + at91_set_A_periph(AT91_PIN_PA20, 1); > + } > + slot_count++; > + break; > + default: > + printk(KERN_ERR > + "AT91: SD/MMC slot %d not available\n", i); > + break; > + } > + if (slot_count) { > + /* CLK */ > + at91_set_A_periph(AT91_PIN_PA12, 0); > + > + mmc0_data = *data; > + platform_device_register(&at91sam9263_mmc0_device); > + } > + } else if (mmc_id == 1) { /* MCI1 */ > + switch (i) { > + case 0: /* slot A */ > + /* CMD */ > + at91_set_A_periph(AT91_PIN_PA7, 1); > + /* DAT0, maybe DAT1..DAT3 */ > + at91_set_A_periph(AT91_PIN_PA8, 1); > + if (data->slot[i].bus_width == 4) { > + at91_set_A_periph(AT91_PIN_PA9, 1); > + at91_set_A_periph(AT91_PIN_PA10, 1); > + at91_set_A_periph(AT91_PIN_PA11, 1); > + } > + slot_count++; > + break; > + case 1: /* slot B */ > + /* CMD */ > + at91_set_A_periph(AT91_PIN_PA21, 1); > + /* DAT0, maybe DAT1..DAT3 */ > + at91_set_A_periph(AT91_PIN_PA22, 1); > + if (data->slot[i].bus_width == 4) { > + at91_set_A_periph(AT91_PIN_PA23, 1); > + at91_set_A_periph(AT91_PIN_PA24, 1); > + at91_set_A_periph(AT91_PIN_PA25, 1); > + } > + slot_count++; > + break; > + default: > + printk(KERN_ERR > + "AT91: SD/MMC slot %d not available\n", i); > + break; > + } > + if (slot_count) { > + /* CLK */ > + at91_set_A_periph(AT91_PIN_PA6, 0); > + > + mmc1_data = *data; > + platform_device_register(&at91sam9263_mmc1_device); > + } > + } > + } > +} > +#else > +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {} > +#endif > + > +/* -------------------------------------------------------------------- > * Compact Flash (PCMCIA or IDE) > * -------------------------------------------------------------------- */ > > diff --git a/arch/arm/mach-at91/at91sam9rl_devices.c b/arch/arm/mach-at91/at91sam9rl_devices.c > index fe4ae22..83c5845 100644 > --- a/arch/arm/mach-at91/at91sam9rl_devices.c > +++ b/arch/arm/mach-at91/at91sam9rl_devices.c > @@ -228,6 +228,76 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {} > > > /* -------------------------------------------------------------------- > + * MMC / SD > + * -------------------------------------------------------------------- */ > + > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static u64 mmc_dmamask = DMA_BIT_MASK(32); > +static struct mci_platform_data mmc_data; > + > +static struct resource mmc_resources[] = { > + [0] = { > + .start = AT91SAM9RL_BASE_MCI, > + .end = AT91SAM9RL_BASE_MCI + SZ_16K - 1, > + .flags = IORESOURCE_MEM, > + }, > + [1] = { > + .start = AT91SAM9RL_ID_MCI, > + .end = AT91SAM9RL_ID_MCI, > + .flags = IORESOURCE_IRQ, > + }, > +}; > + > +static struct platform_device at91sam9rl_mmc_device = { > + .name = "atmel_mci", > + .id = -1, > + .dev = { > + .dma_mask =&mmc_dmamask, > + .coherent_dma_mask = DMA_BIT_MASK(32), > + .platform_data =&mmc_data, > + }, > + .resource = mmc_resources, > + .num_resources = ARRAY_SIZE(mmc_resources), > +}; > + > +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) > +{ > + if (!data) > + return; > + > + if (data->slot[0].bus_width) { > + /* input/irq */ > + if (gpio_is_valid(data->slot[0].detect_pin)) { > + at91_set_gpio_input(data->slot[0].detect_pin, 1); > + at91_set_deglitch(data->slot[0].detect_pin, 1); > + } > + if (gpio_is_valid(data->slot[0].wp_pin)) > + at91_set_gpio_input(data->slot[0].wp_pin, 1); > + > + /* CLK */ > + at91_set_A_periph(AT91_PIN_PA2, 0); > + > + /* CMD */ > + at91_set_A_periph(AT91_PIN_PA1, 1); > + > + /* DAT0, maybe DAT1..DAT3 */ > + at91_set_A_periph(AT91_PIN_PA0, 1); > + if (data->slot[0].bus_width == 4) { > + at91_set_A_periph(AT91_PIN_PA3, 1); > + at91_set_A_periph(AT91_PIN_PA4, 1); > + at91_set_A_periph(AT91_PIN_PA5, 1); > + } > + > + mmc_data = *data; > + platform_device_register(&at91sam9rl_mmc_device); > + } > +} > +#else > +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {} > +#endif > + > + > +/* -------------------------------------------------------------------- > * NAND / SmartMedia > * -------------------------------------------------------------------- */ > > diff --git a/arch/arm/mach-at91/board-afeb-9260v1.c b/arch/arm/mach-at91/board-afeb-9260v1.c > index 161efba..1e294ba 100644 > --- a/arch/arm/mach-at91/board-afeb-9260v1.c > +++ b/arch/arm/mach-at91/board-afeb-9260v1.c > @@ -148,6 +148,15 @@ static struct atmel_nand_data __initdata afeb9260_nand_data = { > /* > * MCI (SD/MMC) > */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata afeb9260_mci0_data = { > + .slot[1] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PC9, > + .wp_pin = AT91_PIN_PC4, > + }, > +}; > +#else > static struct at91_mmc_data __initdata afeb9260_mmc_data = { > .det_pin = AT91_PIN_PC9, > .wp_pin = AT91_PIN_PC4, > @@ -155,6 +164,7 @@ static struct at91_mmc_data __initdata afeb9260_mmc_data = { > .wire4 = 1, > .vcc_pin = -EINVAL, > }; > +#endif > > > > @@ -202,7 +212,11 @@ static void __init afeb9260_board_init(void) > at91_set_B_periph(AT91_PIN_PA10, 0); /* ETX2 */ > at91_set_B_periph(AT91_PIN_PA11, 0); /* ETX3 */ > /* MMC */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&afeb9260_mci0_data); > +#else > at91_add_device_mmc(0,&afeb9260_mmc_data); > +#endif > /* I2C */ > at91_add_device_i2c(afeb9260_i2c_devices, > ARRAY_SIZE(afeb9260_i2c_devices)); > diff --git a/arch/arm/mach-at91/board-carmeva.c b/arch/arm/mach-at91/board-carmeva.c > index 59d9cf9..050b9d5 100644 > --- a/arch/arm/mach-at91/board-carmeva.c > +++ b/arch/arm/mach-at91/board-carmeva.c > @@ -81,6 +81,15 @@ static struct at91_udc_data __initdata carmeva_udc_data = { > // .vcc_pin = -EINVAL, > // }; > > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata carmeva_mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PB10, > + .wp_pin = AT91_PIN_PC14, > + }, > +}; > +#else > static struct at91_mmc_data __initdata carmeva_mmc_data = { > .slot_b = 0, > .wire4 = 1, > @@ -88,6 +97,7 @@ static struct at91_mmc_data __initdata carmeva_mmc_data = { > .wp_pin = AT91_PIN_PC14, > .vcc_pin = -EINVAL, > }; > +#endif > > static struct spi_board_info carmeva_spi_devices[] = { > { /* DataFlash chip */ > @@ -153,7 +163,11 @@ static void __init carmeva_board_init(void) > /* Compact Flash */ > // at91_add_device_cf(&carmeva_cf_data); > /* MMC */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&carmeva_mci0_data); > +#else > at91_add_device_mmc(0,&carmeva_mmc_data); > +#endif > /* LEDs */ > at91_gpio_leds(carmeva_leds, ARRAY_SIZE(carmeva_leds)); > } > diff --git a/arch/arm/mach-at91/board-cpu9krea.c b/arch/arm/mach-at91/board-cpu9krea.c > index 5f3680e..9842297 100644 > --- a/arch/arm/mach-at91/board-cpu9krea.c > +++ b/arch/arm/mach-at91/board-cpu9krea.c > @@ -339,6 +339,15 @@ static void __init cpu9krea_add_device_buttons(void) > /* > * MCI (SD/MMC) > */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata cpu9krea_mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PA29, > + .wp_pin = -EINVAL, > + }, > +}; > +#else > static struct at91_mmc_data __initdata cpu9krea_mmc_data = { > .slot_b = 0, > .wire4 = 1, > @@ -346,6 +355,7 @@ static struct at91_mmc_data __initdata cpu9krea_mmc_data = { > .wp_pin = -EINVAL, > .vcc_pin = -EINVAL, > }; > +#endif > > static void __init cpu9krea_board_init(void) > { > @@ -362,7 +372,11 @@ static void __init cpu9krea_board_init(void) > /* Ethernet */ > at91_add_device_eth(&cpu9krea_macb_data); > /* MMC */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&cpu9krea_mci0_data); > +#else > at91_add_device_mmc(0,&cpu9krea_mmc_data); > +#endif > /* I2C */ > at91_add_device_i2c(cpu9krea_i2c_devices, > ARRAY_SIZE(cpu9krea_i2c_devices)); > diff --git a/arch/arm/mach-at91/board-cpuat91.c b/arch/arm/mach-at91/board-cpuat91.c > index e094cc8..cb5dcbf 100644 > --- a/arch/arm/mach-at91/board-cpuat91.c > +++ b/arch/arm/mach-at91/board-cpuat91.c > @@ -99,12 +99,22 @@ static struct at91_udc_data __initdata cpuat91_udc_data = { > .pullup_pin = AT91_PIN_PC14, > }; > > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata cpuat91_mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PC2, > + .wp_pin = -EINVAL, > + }, > +}; > +#else > static struct at91_mmc_data __initdata cpuat91_mmc_data = { > .det_pin = AT91_PIN_PC2, > .wire4 = 1, > .wp_pin = -EINVAL, > .vcc_pin = -EINVAL, > }; > +#endif > > static struct physmap_flash_data cpuat91_flash_data = { > .width = 2, > @@ -171,7 +181,11 @@ static void __init cpuat91_board_init(void) > /* USB Device */ > at91_add_device_udc(&cpuat91_udc_data); > /* MMC */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&cpuat91_mci0_data); > +#else > at91_add_device_mmc(0,&cpuat91_mmc_data); > +#endif > /* I2C */ > at91_add_device_i2c(NULL, 0); > /* Platform devices */ > diff --git a/arch/arm/mach-at91/board-csb337.c b/arch/arm/mach-at91/board-csb337.c > index 1a1547b..36d65ef 100644 > --- a/arch/arm/mach-at91/board-csb337.c > +++ b/arch/arm/mach-at91/board-csb337.c > @@ -95,6 +95,15 @@ static struct at91_cf_data __initdata csb337_cf_data = { > .rst_pin = AT91_PIN_PD2, > }; > > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata csb337_mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PD5, > + .wp_pin = AT91_PIN_PD6, > + }, > +}; > +#else > static struct at91_mmc_data __initdata csb337_mmc_data = { > .det_pin = AT91_PIN_PD5, > .slot_b = 0, > @@ -102,6 +111,7 @@ static struct at91_mmc_data __initdata csb337_mmc_data = { > .wp_pin = AT91_PIN_PD6, > .vcc_pin = -EINVAL, > }; > +#endif > > static struct spi_board_info csb337_spi_devices[] = { > { /* CAN controller */ > @@ -244,7 +254,11 @@ static void __init csb337_board_init(void) > /* SPI */ > at91_add_device_spi(csb337_spi_devices, ARRAY_SIZE(csb337_spi_devices)); > /* MMC */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&csb337_mci0_data); > +#else > at91_add_device_mmc(0,&csb337_mmc_data); > +#endif > /* NOR flash */ > platform_device_register(&csb_flash); > /* LEDs */ > diff --git a/arch/arm/mach-at91/board-eb9200.c b/arch/arm/mach-at91/board-eb9200.c > index d302ca3..f374ecc 100644 > --- a/arch/arm/mach-at91/board-eb9200.c > +++ b/arch/arm/mach-at91/board-eb9200.c > @@ -83,6 +83,15 @@ static struct at91_cf_data __initdata eb9200_cf_data = { > .rst_pin = AT91_PIN_PC5, > }; > > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata eb9200_mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = -EINVAL, > + .wp_pin = -EINVAL, > + }, > +}; > +#else > static struct at91_mmc_data __initdata eb9200_mmc_data = { > .slot_b = 0, > .wire4 = 1, > @@ -90,6 +99,7 @@ static struct at91_mmc_data __initdata eb9200_mmc_data = { > .wp_pin = -EINVAL, > .vcc_pin = -EINVAL, > }; > +#endif > > static struct i2c_board_info __initdata eb9200_i2c_devices[] = { > { > @@ -116,7 +126,11 @@ static void __init eb9200_board_init(void) > at91_add_device_spi(NULL, 0); > /* MMC */ > /* only supports 1 or 4 bit interface, not wired through to SPI */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&eb9200_mci0_data); > +#else > at91_add_device_mmc(0,&eb9200_mmc_data); > +#endif > } > > MACHINE_START(ATEB9200, "Embest ATEB9200") > diff --git a/arch/arm/mach-at91/board-ecbat91.c b/arch/arm/mach-at91/board-ecbat91.c > index 69966ce..0f39fb3 100644 > --- a/arch/arm/mach-at91/board-ecbat91.c > +++ b/arch/arm/mach-at91/board-ecbat91.c > @@ -75,6 +75,15 @@ static struct at91_usbh_data __initdata ecb_at91usbh_data = { > .overcurrent_pin= {-EINVAL, -EINVAL}, > }; > > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata ecbat91_mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = -EINVAL, > + .wp_pin = -EINVAL, > + }, > +}; > +#else > static struct at91_mmc_data __initdata ecb_at91mmc_data = { > .slot_b = 0, > .wire4 = 1, > @@ -82,6 +91,7 @@ static struct at91_mmc_data __initdata ecb_at91mmc_data = { > .wp_pin = -EINVAL, > .vcc_pin = -EINVAL, > }; > +#endif > > > #if defined(CONFIG_MTD_DATAFLASH) > @@ -164,7 +174,11 @@ static void __init ecb_at91board_init(void) > at91_add_device_i2c(NULL, 0); > > /* MMC */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&ecbat91_mci0_data); > +#else > at91_add_device_mmc(0,&ecb_at91mmc_data); > +#endif > > /* SPI */ > at91_add_device_spi(ecb_at91spi_devices, ARRAY_SIZE(ecb_at91spi_devices)); > diff --git a/arch/arm/mach-at91/board-eco920.c b/arch/arm/mach-at91/board-eco920.c > index f23aabe..932bebd 100644 > --- a/arch/arm/mach-at91/board-eco920.c > +++ b/arch/arm/mach-at91/board-eco920.c > @@ -64,6 +64,15 @@ static struct at91_udc_data __initdata eco920_udc_data = { > .pullup_pin = AT91_PIN_PB13, > }; > > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata eco920_mci0_data = { > + .slot[0] = { > + .bus_width = 1, > + .detect_pin = -EINVAL, > + .wp_pin = -EINVAL, > + }, > +}; > +#else > static struct at91_mmc_data __initdata eco920_mmc_data = { > .slot_b = 0, > .wire4 = 0, > @@ -71,6 +80,7 @@ static struct at91_mmc_data __initdata eco920_mmc_data = { > .wp_pin = -EINVAL, > .vcc_pin = -EINVAL, > }; > +#endif > > static struct physmap_flash_data eco920_flash_data = { > .width = 2, > @@ -108,7 +118,11 @@ static void __init eco920_board_init(void) > at91_add_device_usbh(&eco920_usbh_data); > at91_add_device_udc(&eco920_udc_data); > > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&eco920_mci0_data); > +#else > at91_add_device_mmc(0,&eco920_mmc_data); > +#endif > platform_device_register(&eco920_flash); > > at91_ramc_write(0, AT91_SMC_CSR(7), AT91_SMC_RWHOLD_(1) > diff --git a/arch/arm/mach-at91/board-flexibity.c b/arch/arm/mach-at91/board-flexibity.c > index 1815152..6632a80 100644 > --- a/arch/arm/mach-at91/board-flexibity.c > +++ b/arch/arm/mach-at91/board-flexibity.c > @@ -80,6 +80,15 @@ static struct spi_board_info flexibity_spi_devices[] = { > }; > > /* MCI (SD/MMC) */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata flexibity_mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PC9, > + .wp_pin = AT91_PIN_PC4, > + }, > +}; > +#else > static struct at91_mmc_data __initdata flexibity_mmc_data = { > .slot_b = 0, > .wire4 = 1, > @@ -87,6 +96,7 @@ static struct at91_mmc_data __initdata flexibity_mmc_data = { > .wp_pin = AT91_PIN_PC4, > .vcc_pin = -EINVAL, > }; > +#endif > > /* LEDs */ > static struct gpio_led flexibity_leds[] = { > @@ -155,7 +165,11 @@ static void __init flexibity_board_init(void) > at91_add_device_spi(flexibity_spi_devices, > ARRAY_SIZE(flexibity_spi_devices)); > /* MMC */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&flexibity_mci0_data); > +#else > at91_add_device_mmc(0,&flexibity_mmc_data); > +#endif > /* LEDs */ > at91_gpio_leds(flexibity_leds, ARRAY_SIZE(flexibity_leds)); > } > diff --git a/arch/arm/mach-at91/board-foxg20.c b/arch/arm/mach-at91/board-foxg20.c > index caf017f..6cda303 100644 > --- a/arch/arm/mach-at91/board-foxg20.c > +++ b/arch/arm/mach-at91/board-foxg20.c > @@ -123,7 +123,7 @@ static struct at91_udc_data __initdata foxg20_udc_data = { > * SPI devices. > */ > static struct spi_board_info foxg20_spi_devices[] = { > -#if !defined(CONFIG_MMC_AT91) > +#if !defined(CONFIG_MMC_AT91)&& !defined(CONFIG_MMC_ATMELMCI) > { > .modalias = "mtd_dataflash", > .chip_select = 1, > @@ -146,6 +146,7 @@ static struct macb_platform_data __initdata foxg20_macb_data = { > * MCI (SD/MMC) > * det_pin, wp_pin and vcc_pin are not connected > */ > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > static struct at91_mmc_data __initdata foxg20_mmc_data = { > .slot_b = 1, > .wire4 = 1, > @@ -153,6 +154,15 @@ static struct at91_mmc_data __initdata foxg20_mmc_data = { > .wp_pin = -EINVAL, > .vcc_pin = -EINVAL, > }; > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata foxg20_mci0_data = { > + .slot[1] = { > + .bus_width = 4, > + .detect_pin = -EINVAL, > + .wp_pin = -EINVAL, > + }, > +}; > +#endif > > > /* > @@ -251,7 +261,11 @@ static void __init foxg20_board_init(void) > /* Ethernet */ > at91_add_device_eth(&foxg20_macb_data); > /* MMC */ > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > at91_add_device_mmc(0,&foxg20_mmc_data); > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&foxg20_mci0_data); > +#endif > /* I2C */ > at91_add_device_i2c(foxg20_i2c_devices, ARRAY_SIZE(foxg20_i2c_devices)); > /* LEDs */ > diff --git a/arch/arm/mach-at91/board-kb9202.c b/arch/arm/mach-at91/board-kb9202.c > index 59b92aa..e31ec8e 100644 > --- a/arch/arm/mach-at91/board-kb9202.c > +++ b/arch/arm/mach-at91/board-kb9202.c > @@ -86,6 +86,15 @@ static struct at91_udc_data __initdata kb9202_udc_data = { > .pullup_pin = AT91_PIN_PB22, > }; > > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata kb9202_mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PB2, > + .wp_pin = -EINVAL, > + }, > +}; > +#else > static struct at91_mmc_data __initdata kb9202_mmc_data = { > .det_pin = AT91_PIN_PB2, > .slot_b = 0, > @@ -93,6 +102,7 @@ static struct at91_mmc_data __initdata kb9202_mmc_data = { > .wp_pin = -EINVAL, > .vcc_pin = -EINVAL, > }; > +#endif > > static struct mtd_partition __initdata kb9202_nand_partition[] = { > { > @@ -124,7 +134,11 @@ static void __init kb9202_board_init(void) > /* USB Device */ > at91_add_device_udc(&kb9202_udc_data); > /* MMC */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&kb9202_mci0_data); > +#else > at91_add_device_mmc(0,&kb9202_mmc_data); > +#endif > /* I2C */ > at91_add_device_i2c(NULL, 0); > /* SPI */ > diff --git a/arch/arm/mach-at91/board-neocore926.c b/arch/arm/mach-at91/board-neocore926.c > index 57d5f6a..849b938 100644 > --- a/arch/arm/mach-at91/board-neocore926.c > +++ b/arch/arm/mach-at91/board-neocore926.c > @@ -146,12 +146,22 @@ static struct spi_board_info neocore926_spi_devices[] = { > /* > * MCI (SD/MMC) > */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata neocore926_mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PE18, > + .wp_pin = AT91_PIN_PE19, > + }, > +}; > +#else > static struct at91_mmc_data __initdata neocore926_mmc_data = { > .wire4 = 1, > .det_pin = AT91_PIN_PE18, > .wp_pin = AT91_PIN_PE19, > .vcc_pin = -EINVAL, > }; > +#endif > > > /* > @@ -357,7 +367,11 @@ static void __init neocore926_board_init(void) > neocore926_add_device_ts(); > > /* MMC */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&neocore926_mci0_data); > +#else > at91_add_device_mmc(1,&neocore926_mmc_data); > +#endif > > /* Ethernet */ > at91_add_device_eth(&neocore926_macb_data); > diff --git a/arch/arm/mach-at91/board-picotux200.c b/arch/arm/mach-at91/board-picotux200.c > index 59e35dd..a8cb032 100644 > --- a/arch/arm/mach-at91/board-picotux200.c > +++ b/arch/arm/mach-at91/board-picotux200.c > @@ -72,6 +72,15 @@ static struct at91_usbh_data __initdata picotux200_usbh_data = { > .overcurrent_pin= {-EINVAL, -EINVAL}, > }; > > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata picotux200_mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PB27, > + .wp_pin = AT91_PIN_PA17, > + }, > +}; > +#else > static struct at91_mmc_data __initdata picotux200_mmc_data = { > .det_pin = AT91_PIN_PB27, > .slot_b = 0, > @@ -79,6 +88,7 @@ static struct at91_mmc_data __initdata picotux200_mmc_data = { > .wp_pin = AT91_PIN_PA17, > .vcc_pin = -EINVAL, > }; > +#endif > > #define PICOTUX200_FLASH_BASE AT91_CHIPSELECT_0 > #define PICOTUX200_FLASH_SIZE SZ_4M > @@ -115,7 +125,11 @@ static void __init picotux200_board_init(void) > at91_add_device_i2c(NULL, 0); > /* MMC */ > at91_set_gpio_output(AT91_PIN_PB22, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&picotux200_mci0_data); > +#else > at91_add_device_mmc(0,&picotux200_mmc_data); > +#endif > /* NOR Flash */ > platform_device_register(&picotux200_flash); > } > diff --git a/arch/arm/mach-at91/board-qil-a9260.c b/arch/arm/mach-at91/board-qil-a9260.c > index b6ed5ed..2a49993 100644 > --- a/arch/arm/mach-at91/board-qil-a9260.c > +++ b/arch/arm/mach-at91/board-qil-a9260.c > @@ -173,6 +173,15 @@ static void __init ek_add_device_nand(void) > /* > * MCI (SD/MMC) > */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata ek_mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = -EINVAL, > + .wp_pin = -EINVAL, > + }, > +}; > +#else > static struct at91_mmc_data __initdata ek_mmc_data = { > .slot_b = 0, > .wire4 = 1, > @@ -180,6 +189,7 @@ static struct at91_mmc_data __initdata ek_mmc_data = { > .wp_pin = -EINVAL, > .vcc_pin = -EINVAL, > }; > +#endif > > /* > * GPIO Buttons > @@ -249,7 +259,11 @@ static void __init ek_board_init(void) > /* Ethernet */ > at91_add_device_eth(&ek_macb_data); > /* MMC */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&ek_mci0_data); > +#else > at91_add_device_mmc(0,&ek_mmc_data); > +#endif > /* Push Buttons */ > ek_add_device_buttons(); > /* LEDs */ > diff --git a/arch/arm/mach-at91/board-rm9200dk.c b/arch/arm/mach-at91/board-rm9200dk.c > index 01332aa..b6128fb 100644 > --- a/arch/arm/mach-at91/board-rm9200dk.c > +++ b/arch/arm/mach-at91/board-rm9200dk.c > @@ -90,6 +90,15 @@ static struct at91_cf_data __initdata dk_cf_data = { > }; > > #ifndef CONFIG_MTD_AT91_DATAFLASH_CARD > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata dk_mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = -EINVAL, > + .wp_pin = -EINVAL, > + }, > +}; > +#else > static struct at91_mmc_data __initdata dk_mmc_data = { > .slot_b = 0, > .wire4 = 1, > @@ -98,6 +107,7 @@ static struct at91_mmc_data __initdata dk_mmc_data = { > .vcc_pin = -EINVAL, > }; > #endif > +#endif > > static struct spi_board_info dk_spi_devices[] = { > { /* DataFlash chip */ > @@ -211,8 +221,12 @@ static void __init dk_board_init(void) > #else > /* MMC */ > at91_set_gpio_output(AT91_PIN_PB7, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&dk_mci0_data); > +#else > at91_add_device_mmc(0,&dk_mmc_data); > #endif > +#endif > /* NAND */ > at91_add_device_nand(&dk_nand_data); > /* NOR Flash */ > diff --git a/arch/arm/mach-at91/board-rm9200ek.c b/arch/arm/mach-at91/board-rm9200ek.c > index b2e4fe2..7177aac 100644 > --- a/arch/arm/mach-at91/board-rm9200ek.c > +++ b/arch/arm/mach-at91/board-rm9200ek.c > @@ -83,6 +83,7 @@ static struct at91_udc_data __initdata ek_udc_data = { > }; > > #ifndef CONFIG_MTD_AT91_DATAFLASH_CARD > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > static struct at91_mmc_data __initdata ek_mmc_data = { > .det_pin = AT91_PIN_PB27, > .slot_b = 0, > @@ -90,6 +91,15 @@ static struct at91_mmc_data __initdata ek_mmc_data = { > .wp_pin = AT91_PIN_PA17, > .vcc_pin = -EINVAL, > }; > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata ek_mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PB27, > + .wp_pin = AT91_PIN_PA17, > + } > +}; > +#endif > #endif > > static struct spi_board_info ek_spi_devices[] = { > @@ -180,7 +190,11 @@ static void __init ek_board_init(void) > #else > /* MMC */ > at91_set_gpio_output(AT91_PIN_PB22, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */ > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > at91_add_device_mmc(0,&ek_mmc_data); > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&ek_mci0_data); > +#endif > #endif > /* NOR Flash */ > platform_device_register(&ek_flash); > diff --git a/arch/arm/mach-at91/board-rsi-ews.c b/arch/arm/mach-at91/board-rsi-ews.c > index af0750f..373537a 100644 > --- a/arch/arm/mach-at91/board-rsi-ews.c > +++ b/arch/arm/mach-at91/board-rsi-ews.c > @@ -77,12 +77,22 @@ static struct at91_usbh_data rsi_ews_usbh_data __initdata = { > /* > * SD/MC > */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata rsi_ews_mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PB27, > + .wp_pin = AT91_PIN_PB29, > + }, > +}; > +#else > static struct at91_mmc_data rsi_ews_mmc_data __initdata = { > .slot_b = 0, > .wire4 = 1, > .det_pin = AT91_PIN_PB27, > .wp_pin = AT91_PIN_PB29, > }; > +#endif > > /* > * I2C > @@ -218,7 +228,11 @@ static void __init rsi_ews_board_init(void) > at91_add_device_spi(rsi_ews_spi_devices, > ARRAY_SIZE(rsi_ews_spi_devices)); > /* MMC */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&rsi_ews_mci0_data); > +#else > at91_add_device_mmc(0,&rsi_ews_mmc_data); > +#endif > /* NOR Flash */ > platform_device_register(&rsiews_nor_flash); > /* LEDs */ > diff --git a/arch/arm/mach-at91/board-sam9-l9260.c b/arch/arm/mach-at91/board-sam9-l9260.c > index e8b116b..7562011 100644 > --- a/arch/arm/mach-at91/board-sam9-l9260.c > +++ b/arch/arm/mach-at91/board-sam9-l9260.c > @@ -89,7 +89,7 @@ static struct at91_udc_data __initdata ek_udc_data = { > * SPI devices. > */ > static struct spi_board_info ek_spi_devices[] = { > -#if !defined(CONFIG_MMC_AT91) > +#if !defined(CONFIG_MMC_AT91)&& !defined(CONFIG_MMC_ATMELMCI) > { /* DataFlash chip */ > .modalias = "mtd_dataflash", > .chip_select = 1, > @@ -174,6 +174,15 @@ static void __init ek_add_device_nand(void) > /* > * MCI (SD/MMC) > */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata ek_mci0_data = { > + .slot[1] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PC8, > + .wp_pin = AT91_PIN_PC4, > + }, > +}; > +#else > static struct at91_mmc_data __initdata ek_mmc_data = { > .slot_b = 1, > .wire4 = 1, > @@ -181,6 +190,7 @@ static struct at91_mmc_data __initdata ek_mmc_data = { > .wp_pin = AT91_PIN_PC4, > .vcc_pin = -EINVAL, > }; > +#endif > > static void __init ek_board_init(void) > { > @@ -197,7 +207,11 @@ static void __init ek_board_init(void) > /* Ethernet */ > at91_add_device_eth(&ek_macb_data); > /* MMC */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&ek_mci0_data); > +#else > at91_add_device_mmc(0,&ek_mmc_data); > +#endif > /* I2C */ > at91_add_device_i2c(NULL, 0); > } > diff --git a/arch/arm/mach-at91/board-sam9260ek.c b/arch/arm/mach-at91/board-sam9260ek.c > index d5aec55..b39009e 100644 > --- a/arch/arm/mach-at91/board-sam9260ek.c > +++ b/arch/arm/mach-at91/board-sam9260ek.c > @@ -121,7 +121,7 @@ static void __init at73c213_set_clk(struct at73c213_board_info *info) {} > * SPI devices. > */ > static struct spi_board_info ek_spi_devices[] = { > -#if !defined(CONFIG_MMC_AT91) > +#if !defined(CONFIG_MMC_AT91)&& !defined(CONFIG_MMC_ATMELMCI) > { /* DataFlash chip */ > .modalias = "mtd_dataflash", > .chip_select = 1, > @@ -224,6 +224,15 @@ static void __init ek_add_device_nand(void) > /* > * MCI (SD/MMC) > */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata ek_mci0_data = { > + .slot[1] = { > + .bus_width = 4, > + .detect_pin = -EINVAL, > + .wp_pin = -EINVAL, > + }, > +}; > +#else > static struct at91_mmc_data __initdata ek_mmc_data = { > .slot_b = 1, > .wire4 = 1, > @@ -231,6 +240,7 @@ static struct at91_mmc_data __initdata ek_mmc_data = { > .wp_pin = -EINVAL, > .vcc_pin = -EINVAL, > }; > +#endif > > > /* > @@ -332,7 +342,11 @@ static void __init ek_board_init(void) > /* Ethernet */ > at91_add_device_eth(&ek_macb_data); > /* MMC */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&ek_mci0_data); > +#else > at91_add_device_mmc(0,&ek_mmc_data); > +#endif > /* I2C */ > at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices)); > /* SSC (to AT73C213) */ > diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c > index 065fed3..797dd7c 100644 > --- a/arch/arm/mach-at91/board-sam9261ek.c > +++ b/arch/arm/mach-at91/board-sam9261ek.c > @@ -344,6 +344,7 @@ static struct spi_board_info ek_spi_devices[] = { > #else /* CONFIG_SPI_ATMEL_* */ > /* spi0 and mmc/sd share the same PIO pins: cannot be used at the same time */ > > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > /* > * MCI (SD/MMC) > * det_pin, wp_pin and vcc_pin are not connected > @@ -354,6 +355,15 @@ static struct at91_mmc_data __initdata ek_mmc_data = { > .wp_pin = -EINVAL, > .vcc_pin = -EINVAL, > }; > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = -EINVAL, > + .wp_pin = -EINVAL, > + }, > +}; > +#endif > > #endif /* CONFIG_SPI_ATMEL_* */ > > @@ -601,7 +611,11 @@ static void __init ek_board_init(void) > at91_add_device_ssc(AT91SAM9261_ID_SSC1, ATMEL_SSC_TX); > #else > /* MMC */ > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > at91_add_device_mmc(0,&ek_mmc_data); > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&mci0_data); > +#endif > #endif > /* LCD Controller */ > at91_add_device_lcdc(&ek_lcdc_data); > diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c > index 2ffe50f..419c57a 100644 > --- a/arch/arm/mach-at91/board-sam9263ek.c > +++ b/arch/arm/mach-at91/board-sam9263ek.c > @@ -149,12 +149,22 @@ static struct spi_board_info ek_spi_devices[] = { > /* > * MCI (SD/MMC) > */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata mci1_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PE18, > + .wp_pin = AT91_PIN_PE19, > + }, > +}; > +#else > static struct at91_mmc_data __initdata ek_mmc_data = { > .wire4 = 1, > .det_pin = AT91_PIN_PE18, > .wp_pin = AT91_PIN_PE19, > .vcc_pin = -EINVAL, > }; > +#endif > > > /* > @@ -423,7 +433,11 @@ static void __init ek_board_init(void) > /* Touchscreen */ > ek_add_device_ts(); > /* MMC */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(1,&mci1_data); > +#else > at91_add_device_mmc(1,&ek_mmc_data); > +#endif > /* Ethernet */ > at91_add_device_eth(&ek_macb_data); > /* NAND */ > diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c > index b109ce2..bb06521 100644 > --- a/arch/arm/mach-at91/board-sam9rlek.c > +++ b/arch/arm/mach-at91/board-sam9rlek.c > @@ -64,12 +64,22 @@ static struct usba_platform_data __initdata ek_usba_udc_data = { > /* > * MCI (SD/MMC) > */ > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > static struct at91_mmc_data __initdata ek_mmc_data = { > .wire4 = 1, > .det_pin = AT91_PIN_PA15, > .wp_pin = -EINVAL, > .vcc_pin = -EINVAL, > }; > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PA15, > + .wp_pin = -EINVAL, > + }, > +}; > +#endif > > > /* > @@ -306,7 +316,11 @@ static void __init ek_board_init(void) > /* SPI */ > at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); > /* MMC */ > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > at91_add_device_mmc(0,&ek_mmc_data); > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&mci0_data); > +#endif > /* LCD Controller */ > at91_add_device_lcdc(&ek_lcdc_data); > /* AC97 */ > diff --git a/arch/arm/mach-at91/board-usb-a926x.c b/arch/arm/mach-at91/board-usb-a926x.c > index b7483a3..879e34e 100644 > --- a/arch/arm/mach-at91/board-usb-a926x.c > +++ b/arch/arm/mach-at91/board-usb-a926x.c > @@ -114,7 +114,7 @@ static struct mmc_spi_platform_data at91_mmc_spi_pdata = { > * SPI devices. > */ > static struct spi_board_info usb_a9263_spi_devices[] = { > -#if !defined(CONFIG_MMC_AT91) > +#if !defined(CONFIG_MMC_AT91)&& !defined(CONFIG_MMC_ATMELMCI) > { /* DataFlash chip */ > .modalias = "mtd_dataflash", > .chip_select = 0, > diff --git a/arch/arm/mach-at91/board-yl-9200.c b/arch/arm/mach-at91/board-yl-9200.c > index 38dd279..3d3b8a6 100644 > --- a/arch/arm/mach-at91/board-yl-9200.c > +++ b/arch/arm/mach-at91/board-yl-9200.c > @@ -138,12 +138,22 @@ static struct at91_udc_data __initdata yl9200_udc_data = { > /* > * MMC > */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata yl9200_mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PB9, > + .wp_pin = -EINVAL, > + }, > +}; > +#else > static struct at91_mmc_data __initdata yl9200_mmc_data = { > .det_pin = AT91_PIN_PB9, > .wire4 = 1, > .wp_pin = -EINVAL, > .vcc_pin = -EINVAL, > }; > +#endif > > /* > * NAND Flash > @@ -571,7 +581,11 @@ static void __init yl9200_board_init(void) > /* I2C */ > at91_add_device_i2c(yl9200_i2c_devices, ARRAY_SIZE(yl9200_i2c_devices)); > /* MMC */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&yl9200_mci0_data); > +#else > at91_add_device_mmc(0,&yl9200_mmc_data); > +#endif > /* NAND */ > at91_add_device_nand(&yl9200_nand_data); > /* NOR Flash */ ^ permalink raw reply [flat|nested] 28+ messages in thread
* [PATCH v2] ARM: at91: add atmel-mci support for chips and boards which can use it @ 2012-05-21 10:31 ` ludovic.desroches 0 siblings, 0 replies; 28+ messages in thread From: ludovic.desroches @ 2012-05-21 10:31 UTC (permalink / raw) To: linux-arm-kernel Le 05/21/2012 12:23 PM, ludovic.desroches at atmel.com a ?crit : > From: Ludovic Desroches<ludovic.desroches@atmel.com> > > Since atmel-mci driver supports all atmel mci version excepted the rm9200 one, > use it instead of at91_mci driver. Sorry commit message is wrong. Since atmel-mci driver supports all atmel mci versions, use it instead of at91_mci driver. > > Signed-off-by: Ludovic Desroches<ludovic.desroches@atmel.com> > --- > V2: add several boards I missed > > arch/arm/mach-at91/at91rm9200_devices.c | 99 ++++++++++++++++++ > arch/arm/mach-at91/at91sam9261_devices.c | 67 ++++++++++++ > arch/arm/mach-at91/at91sam9263.c | 2 + > arch/arm/mach-at91/at91sam9263_devices.c | 164 ++++++++++++++++++++++++++++++ > arch/arm/mach-at91/at91sam9rl_devices.c | 70 +++++++++++++ > arch/arm/mach-at91/board-afeb-9260v1.c | 14 +++ > arch/arm/mach-at91/board-carmeva.c | 14 +++ > arch/arm/mach-at91/board-cpu9krea.c | 14 +++ > arch/arm/mach-at91/board-cpuat91.c | 14 +++ > arch/arm/mach-at91/board-csb337.c | 14 +++ > arch/arm/mach-at91/board-eb9200.c | 14 +++ > arch/arm/mach-at91/board-ecbat91.c | 14 +++ > arch/arm/mach-at91/board-eco920.c | 14 +++ > arch/arm/mach-at91/board-flexibity.c | 14 +++ > arch/arm/mach-at91/board-foxg20.c | 16 +++- > arch/arm/mach-at91/board-kb9202.c | 14 +++ > arch/arm/mach-at91/board-neocore926.c | 14 +++ > arch/arm/mach-at91/board-picotux200.c | 14 +++ > arch/arm/mach-at91/board-qil-a9260.c | 14 +++ > arch/arm/mach-at91/board-rm9200dk.c | 14 +++ > arch/arm/mach-at91/board-rm9200ek.c | 14 +++ > arch/arm/mach-at91/board-rsi-ews.c | 14 +++ > arch/arm/mach-at91/board-sam9-l9260.c | 16 +++- > arch/arm/mach-at91/board-sam9260ek.c | 16 +++- > arch/arm/mach-at91/board-sam9261ek.c | 14 +++ > arch/arm/mach-at91/board-sam9263ek.c | 14 +++ > arch/arm/mach-at91/board-sam9rlek.c | 14 +++ > arch/arm/mach-at91/board-usb-a926x.c | 2 +- > arch/arm/mach-at91/board-yl-9200.c | 14 +++ > 29 files changed, 728 insertions(+), 4 deletions(-) > > diff --git a/arch/arm/mach-at91/at91rm9200_devices.c b/arch/arm/mach-at91/at91rm9200_devices.c > index 05774e5..2c13783 100644 > --- a/arch/arm/mach-at91/at91rm9200_devices.c > +++ b/arch/arm/mach-at91/at91rm9200_devices.c > @@ -374,6 +374,105 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {} > > > /* -------------------------------------------------------------------- > + * MMC / SD > + * -------------------------------------------------------------------- */ > + > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static u64 mmc_dmamask = DMA_BIT_MASK(32); > +static struct mci_platform_data mmc_data; > + > +static struct resource mmc_resources[] = { > + [0] = { > + .start = AT91RM9200_BASE_MCI, > + .end = AT91RM9200_BASE_MCI + SZ_16K - 1, > + .flags = IORESOURCE_MEM, > + }, > + [1] = { > + .start = AT91RM9200_ID_MCI, > + .end = AT91RM9200_ID_MCI, > + .flags = IORESOURCE_IRQ, > + }, > +}; > + > +static struct platform_device at91rm9200_mmc_device = { > + .name = "atmel_mci", > + .id = -1, > + .dev = { > + .dma_mask =&mmc_dmamask, > + .coherent_dma_mask = DMA_BIT_MASK(32), > + .platform_data =&mmc_data, > + }, > + .resource = mmc_resources, > + .num_resources = ARRAY_SIZE(mmc_resources), > +}; > + > +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) > +{ > + unsigned int i; > + unsigned int slot_count = 0; > + > + if (!data) > + return; > + > + for (i = 0; i< ATMCI_MAX_NR_SLOTS; i++) { > + > + if (!data->slot[i].bus_width) > + continue; > + > + /* input/irq */ > + if (gpio_is_valid(data->slot[i].detect_pin)) { > + at91_set_gpio_input(data->slot[i].detect_pin, 1); > + at91_set_deglitch(data->slot[i].detect_pin, 1); > + } > + if (gpio_is_valid(data->slot[i].wp_pin)) > + at91_set_gpio_input(data->slot[i].wp_pin, 1); > + > + switch (i) { > + case 0: /* slot A */ > + /* CMD */ > + at91_set_A_periph(AT91_PIN_PA28, 1); > + /* DAT0, maybe DAT1..DAT3 */ > + at91_set_A_periph(AT91_PIN_PA29, 1); > + if (data->slot[i].bus_width == 4) { > + at91_set_B_periph(AT91_PIN_PB3, 1); > + at91_set_B_periph(AT91_PIN_PB4, 1); > + at91_set_B_periph(AT91_PIN_PB5, 1); > + } > + slot_count++; > + break; > + case 1: /* slot B */ > + /* CMD */ > + at91_set_B_periph(AT91_PIN_PA8, 1); > + /* DAT0, maybe DAT1..DAT3 */ > + at91_set_B_periph(AT91_PIN_PA9, 1); > + if (data->slot[i].bus_width == 4) { > + at91_set_B_periph(AT91_PIN_PA10, 1); > + at91_set_B_periph(AT91_PIN_PA11, 1); > + at91_set_B_periph(AT91_PIN_PA12, 1); > + } > + slot_count++; > + break; > + default: > + printk(KERN_ERR > + "AT91: SD/MMC slot %d not available\n", i); > + break; > + } > + if (slot_count) { > + /* CLK */ > + at91_set_A_periph(AT91_PIN_PA27, 0); > + > + mmc_data = *data; > + platform_device_register(&at91rm9200_mmc_device); > + } > + } > + > +} > +#else > +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {} > +#endif > + > + > +/* -------------------------------------------------------------------- > * NAND / SmartMedia > * -------------------------------------------------------------------- */ > > diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c > index 4db961a..0817854 100644 > --- a/arch/arm/mach-at91/at91sam9261_devices.c > +++ b/arch/arm/mach-at91/at91sam9261_devices.c > @@ -202,7 +202,74 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) > void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {} > #endif > > +/* -------------------------------------------------------------------- > + * MMC / SD Slot for Atmel MCI Driver > + * -------------------------------------------------------------------- */ > + > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static u64 mmc_dmamask = DMA_BIT_MASK(32); > +static struct mci_platform_data mmc_data; > + > +static struct resource mmc_resources[] = { > + [0] = { > + .start = AT91SAM9261_BASE_MCI, > + .end = AT91SAM9261_BASE_MCI + SZ_16K - 1, > + .flags = IORESOURCE_MEM, > + }, > + [1] = { > + .start = AT91SAM9261_ID_MCI, > + .end = AT91SAM9261_ID_MCI, > + .flags = IORESOURCE_IRQ, > + }, > +}; > + > +static struct platform_device at91sam9261_mmc_device = { > + .name = "atmel_mci", > + .id = -1, > + .dev = { > + .dma_mask =&mmc_dmamask, > + .coherent_dma_mask = DMA_BIT_MASK(32), > + .platform_data =&mmc_data, > + }, > + .resource = mmc_resources, > + .num_resources = ARRAY_SIZE(mmc_resources), > +}; > + > +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) > +{ > + if (!data) > + return; > > + if (data->slot[0].bus_width) { > + /* input/irq */ > + if (gpio_is_valid(data->slot[0].detect_pin)) { > + at91_set_gpio_input(data->slot[0].detect_pin, 1); > + at91_set_deglitch(data->slot[0].detect_pin, 1); > + } > + if (gpio_is_valid(data->slot[0].wp_pin)) > + at91_set_gpio_input(data->slot[0].wp_pin, 1); > + > + /* CLK */ > + at91_set_B_periph(AT91_PIN_PA2, 0); > + > + /* CMD */ > + at91_set_B_periph(AT91_PIN_PA1, 1); > + > + /* DAT0, maybe DAT1..DAT3 */ > + at91_set_B_periph(AT91_PIN_PA0, 1); > + if (data->slot[0].bus_width == 4) { > + at91_set_B_periph(AT91_PIN_PA4, 1); > + at91_set_B_periph(AT91_PIN_PA5, 1); > + at91_set_B_periph(AT91_PIN_PA6, 1); > + } > + > + mmc_data = *data; > + platform_device_register(&at91sam9261_mmc_device); > + } > +} > +#else > +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {} > +#endif > /* -------------------------------------------------------------------- > * NAND / SmartMedia > * -------------------------------------------------------------------- */ > diff --git a/arch/arm/mach-at91/at91sam9263.c b/arch/arm/mach-at91/at91sam9263.c > index ef301be..053e47a 100644 > --- a/arch/arm/mach-at91/at91sam9263.c > +++ b/arch/arm/mach-at91/at91sam9263.c > @@ -189,6 +189,8 @@ static struct clk_lookup periph_clocks_lookups[] = { > CLKDEV_CON_DEV_ID("pclk", "ssc.1",&ssc1_clk), > CLKDEV_CON_DEV_ID("mci_clk", "at91_mci.0",&mmc0_clk), > CLKDEV_CON_DEV_ID("mci_clk", "at91_mci.1",&mmc1_clk), > + CLKDEV_CON_DEV_ID("mci_clk", "atmel_mci.0",&mmc0_clk), > + CLKDEV_CON_DEV_ID("mci_clk", "atmel_mci.1",&mmc1_clk), > CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.0",&spi0_clk), > CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.1",&spi1_clk), > CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0",&tcb_clk), > diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c > index fe99206..617fbfc 100644 > --- a/arch/arm/mach-at91/at91sam9263_devices.c > +++ b/arch/arm/mach-at91/at91sam9263_devices.c > @@ -354,6 +354,170 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {} > #endif > > /* -------------------------------------------------------------------- > + * MMC / SD > + * -------------------------------------------------------------------- */ > + > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static u64 mmc_dmamask = DMA_BIT_MASK(32); > +static struct mci_platform_data mmc0_data, mmc1_data; > + > +static struct resource mmc0_resources[] = { > + [0] = { > + .start = AT91SAM9263_BASE_MCI0, > + .end = AT91SAM9263_BASE_MCI0 + SZ_16K - 1, > + .flags = IORESOURCE_MEM, > + }, > + [1] = { > + .start = AT91SAM9263_ID_MCI0, > + .end = AT91SAM9263_ID_MCI0, > + .flags = IORESOURCE_IRQ, > + }, > +}; > + > +static struct platform_device at91sam9263_mmc0_device = { > + .name = "atmel_mci", > + .id = 0, > + .dev = { > + .dma_mask =&mmc_dmamask, > + .coherent_dma_mask = DMA_BIT_MASK(32), > + .platform_data =&mmc0_data, > + }, > + .resource = mmc0_resources, > + .num_resources = ARRAY_SIZE(mmc0_resources), > +}; > + > +static struct resource mmc1_resources[] = { > + [0] = { > + .start = AT91SAM9263_BASE_MCI1, > + .end = AT91SAM9263_BASE_MCI1 + SZ_16K - 1, > + .flags = IORESOURCE_MEM, > + }, > + [1] = { > + .start = AT91SAM9263_ID_MCI1, > + .end = AT91SAM9263_ID_MCI1, > + .flags = IORESOURCE_IRQ, > + }, > +}; > + > +static struct platform_device at91sam9263_mmc1_device = { > + .name = "atmel_mci", > + .id = 1, > + .dev = { > + .dma_mask =&mmc_dmamask, > + .coherent_dma_mask = DMA_BIT_MASK(32), > + .platform_data =&mmc1_data, > + }, > + .resource = mmc1_resources, > + .num_resources = ARRAY_SIZE(mmc1_resources), > +}; > + > +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) > +{ > + unsigned int i; > + unsigned int slot_count = 0; > + > + if (!data) > + return; > + > + for (i = 0; i< ATMCI_MAX_NR_SLOTS; i++) { > + > + if (!data->slot[i].bus_width) > + continue; > + > + /* input/irq */ > + if (gpio_is_valid(data->slot[i].detect_pin)) { > + at91_set_gpio_input(data->slot[i].detect_pin, > + 1); > + at91_set_deglitch(data->slot[i].detect_pin, > + 1); > + } > + if (gpio_is_valid(data->slot[i].wp_pin)) > + at91_set_gpio_input(data->slot[i].wp_pin, 1); > + > + if (mmc_id == 0) { /* MCI0 */ > + switch (i) { > + case 0: /* slot A */ > + /* CMD */ > + at91_set_A_periph(AT91_PIN_PA1, 1); > + /* DAT0, maybe DAT1..DAT3 */ > + at91_set_A_periph(AT91_PIN_PA0, 1); > + if (data->slot[i].bus_width == 4) { > + at91_set_A_periph(AT91_PIN_PA3, 1); > + at91_set_A_periph(AT91_PIN_PA4, 1); > + at91_set_A_periph(AT91_PIN_PA5, 1); > + } > + slot_count++; > + break; > + case 1: /* slot B */ > + /* CMD */ > + at91_set_A_periph(AT91_PIN_PA16, 1); > + /* DAT0, maybe DAT1..DAT3 */ > + at91_set_A_periph(AT91_PIN_PA17, 1); > + if (data->slot[i].bus_width == 4) { > + at91_set_A_periph(AT91_PIN_PA18, 1); > + at91_set_A_periph(AT91_PIN_PA19, 1); > + at91_set_A_periph(AT91_PIN_PA20, 1); > + } > + slot_count++; > + break; > + default: > + printk(KERN_ERR > + "AT91: SD/MMC slot %d not available\n", i); > + break; > + } > + if (slot_count) { > + /* CLK */ > + at91_set_A_periph(AT91_PIN_PA12, 0); > + > + mmc0_data = *data; > + platform_device_register(&at91sam9263_mmc0_device); > + } > + } else if (mmc_id == 1) { /* MCI1 */ > + switch (i) { > + case 0: /* slot A */ > + /* CMD */ > + at91_set_A_periph(AT91_PIN_PA7, 1); > + /* DAT0, maybe DAT1..DAT3 */ > + at91_set_A_periph(AT91_PIN_PA8, 1); > + if (data->slot[i].bus_width == 4) { > + at91_set_A_periph(AT91_PIN_PA9, 1); > + at91_set_A_periph(AT91_PIN_PA10, 1); > + at91_set_A_periph(AT91_PIN_PA11, 1); > + } > + slot_count++; > + break; > + case 1: /* slot B */ > + /* CMD */ > + at91_set_A_periph(AT91_PIN_PA21, 1); > + /* DAT0, maybe DAT1..DAT3 */ > + at91_set_A_periph(AT91_PIN_PA22, 1); > + if (data->slot[i].bus_width == 4) { > + at91_set_A_periph(AT91_PIN_PA23, 1); > + at91_set_A_periph(AT91_PIN_PA24, 1); > + at91_set_A_periph(AT91_PIN_PA25, 1); > + } > + slot_count++; > + break; > + default: > + printk(KERN_ERR > + "AT91: SD/MMC slot %d not available\n", i); > + break; > + } > + if (slot_count) { > + /* CLK */ > + at91_set_A_periph(AT91_PIN_PA6, 0); > + > + mmc1_data = *data; > + platform_device_register(&at91sam9263_mmc1_device); > + } > + } > + } > +} > +#else > +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {} > +#endif > + > +/* -------------------------------------------------------------------- > * Compact Flash (PCMCIA or IDE) > * -------------------------------------------------------------------- */ > > diff --git a/arch/arm/mach-at91/at91sam9rl_devices.c b/arch/arm/mach-at91/at91sam9rl_devices.c > index fe4ae22..83c5845 100644 > --- a/arch/arm/mach-at91/at91sam9rl_devices.c > +++ b/arch/arm/mach-at91/at91sam9rl_devices.c > @@ -228,6 +228,76 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {} > > > /* -------------------------------------------------------------------- > + * MMC / SD > + * -------------------------------------------------------------------- */ > + > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static u64 mmc_dmamask = DMA_BIT_MASK(32); > +static struct mci_platform_data mmc_data; > + > +static struct resource mmc_resources[] = { > + [0] = { > + .start = AT91SAM9RL_BASE_MCI, > + .end = AT91SAM9RL_BASE_MCI + SZ_16K - 1, > + .flags = IORESOURCE_MEM, > + }, > + [1] = { > + .start = AT91SAM9RL_ID_MCI, > + .end = AT91SAM9RL_ID_MCI, > + .flags = IORESOURCE_IRQ, > + }, > +}; > + > +static struct platform_device at91sam9rl_mmc_device = { > + .name = "atmel_mci", > + .id = -1, > + .dev = { > + .dma_mask =&mmc_dmamask, > + .coherent_dma_mask = DMA_BIT_MASK(32), > + .platform_data =&mmc_data, > + }, > + .resource = mmc_resources, > + .num_resources = ARRAY_SIZE(mmc_resources), > +}; > + > +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) > +{ > + if (!data) > + return; > + > + if (data->slot[0].bus_width) { > + /* input/irq */ > + if (gpio_is_valid(data->slot[0].detect_pin)) { > + at91_set_gpio_input(data->slot[0].detect_pin, 1); > + at91_set_deglitch(data->slot[0].detect_pin, 1); > + } > + if (gpio_is_valid(data->slot[0].wp_pin)) > + at91_set_gpio_input(data->slot[0].wp_pin, 1); > + > + /* CLK */ > + at91_set_A_periph(AT91_PIN_PA2, 0); > + > + /* CMD */ > + at91_set_A_periph(AT91_PIN_PA1, 1); > + > + /* DAT0, maybe DAT1..DAT3 */ > + at91_set_A_periph(AT91_PIN_PA0, 1); > + if (data->slot[0].bus_width == 4) { > + at91_set_A_periph(AT91_PIN_PA3, 1); > + at91_set_A_periph(AT91_PIN_PA4, 1); > + at91_set_A_periph(AT91_PIN_PA5, 1); > + } > + > + mmc_data = *data; > + platform_device_register(&at91sam9rl_mmc_device); > + } > +} > +#else > +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {} > +#endif > + > + > +/* -------------------------------------------------------------------- > * NAND / SmartMedia > * -------------------------------------------------------------------- */ > > diff --git a/arch/arm/mach-at91/board-afeb-9260v1.c b/arch/arm/mach-at91/board-afeb-9260v1.c > index 161efba..1e294ba 100644 > --- a/arch/arm/mach-at91/board-afeb-9260v1.c > +++ b/arch/arm/mach-at91/board-afeb-9260v1.c > @@ -148,6 +148,15 @@ static struct atmel_nand_data __initdata afeb9260_nand_data = { > /* > * MCI (SD/MMC) > */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata afeb9260_mci0_data = { > + .slot[1] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PC9, > + .wp_pin = AT91_PIN_PC4, > + }, > +}; > +#else > static struct at91_mmc_data __initdata afeb9260_mmc_data = { > .det_pin = AT91_PIN_PC9, > .wp_pin = AT91_PIN_PC4, > @@ -155,6 +164,7 @@ static struct at91_mmc_data __initdata afeb9260_mmc_data = { > .wire4 = 1, > .vcc_pin = -EINVAL, > }; > +#endif > > > > @@ -202,7 +212,11 @@ static void __init afeb9260_board_init(void) > at91_set_B_periph(AT91_PIN_PA10, 0); /* ETX2 */ > at91_set_B_periph(AT91_PIN_PA11, 0); /* ETX3 */ > /* MMC */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&afeb9260_mci0_data); > +#else > at91_add_device_mmc(0,&afeb9260_mmc_data); > +#endif > /* I2C */ > at91_add_device_i2c(afeb9260_i2c_devices, > ARRAY_SIZE(afeb9260_i2c_devices)); > diff --git a/arch/arm/mach-at91/board-carmeva.c b/arch/arm/mach-at91/board-carmeva.c > index 59d9cf9..050b9d5 100644 > --- a/arch/arm/mach-at91/board-carmeva.c > +++ b/arch/arm/mach-at91/board-carmeva.c > @@ -81,6 +81,15 @@ static struct at91_udc_data __initdata carmeva_udc_data = { > // .vcc_pin = -EINVAL, > // }; > > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata carmeva_mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PB10, > + .wp_pin = AT91_PIN_PC14, > + }, > +}; > +#else > static struct at91_mmc_data __initdata carmeva_mmc_data = { > .slot_b = 0, > .wire4 = 1, > @@ -88,6 +97,7 @@ static struct at91_mmc_data __initdata carmeva_mmc_data = { > .wp_pin = AT91_PIN_PC14, > .vcc_pin = -EINVAL, > }; > +#endif > > static struct spi_board_info carmeva_spi_devices[] = { > { /* DataFlash chip */ > @@ -153,7 +163,11 @@ static void __init carmeva_board_init(void) > /* Compact Flash */ > // at91_add_device_cf(&carmeva_cf_data); > /* MMC */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&carmeva_mci0_data); > +#else > at91_add_device_mmc(0,&carmeva_mmc_data); > +#endif > /* LEDs */ > at91_gpio_leds(carmeva_leds, ARRAY_SIZE(carmeva_leds)); > } > diff --git a/arch/arm/mach-at91/board-cpu9krea.c b/arch/arm/mach-at91/board-cpu9krea.c > index 5f3680e..9842297 100644 > --- a/arch/arm/mach-at91/board-cpu9krea.c > +++ b/arch/arm/mach-at91/board-cpu9krea.c > @@ -339,6 +339,15 @@ static void __init cpu9krea_add_device_buttons(void) > /* > * MCI (SD/MMC) > */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata cpu9krea_mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PA29, > + .wp_pin = -EINVAL, > + }, > +}; > +#else > static struct at91_mmc_data __initdata cpu9krea_mmc_data = { > .slot_b = 0, > .wire4 = 1, > @@ -346,6 +355,7 @@ static struct at91_mmc_data __initdata cpu9krea_mmc_data = { > .wp_pin = -EINVAL, > .vcc_pin = -EINVAL, > }; > +#endif > > static void __init cpu9krea_board_init(void) > { > @@ -362,7 +372,11 @@ static void __init cpu9krea_board_init(void) > /* Ethernet */ > at91_add_device_eth(&cpu9krea_macb_data); > /* MMC */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&cpu9krea_mci0_data); > +#else > at91_add_device_mmc(0,&cpu9krea_mmc_data); > +#endif > /* I2C */ > at91_add_device_i2c(cpu9krea_i2c_devices, > ARRAY_SIZE(cpu9krea_i2c_devices)); > diff --git a/arch/arm/mach-at91/board-cpuat91.c b/arch/arm/mach-at91/board-cpuat91.c > index e094cc8..cb5dcbf 100644 > --- a/arch/arm/mach-at91/board-cpuat91.c > +++ b/arch/arm/mach-at91/board-cpuat91.c > @@ -99,12 +99,22 @@ static struct at91_udc_data __initdata cpuat91_udc_data = { > .pullup_pin = AT91_PIN_PC14, > }; > > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata cpuat91_mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PC2, > + .wp_pin = -EINVAL, > + }, > +}; > +#else > static struct at91_mmc_data __initdata cpuat91_mmc_data = { > .det_pin = AT91_PIN_PC2, > .wire4 = 1, > .wp_pin = -EINVAL, > .vcc_pin = -EINVAL, > }; > +#endif > > static struct physmap_flash_data cpuat91_flash_data = { > .width = 2, > @@ -171,7 +181,11 @@ static void __init cpuat91_board_init(void) > /* USB Device */ > at91_add_device_udc(&cpuat91_udc_data); > /* MMC */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&cpuat91_mci0_data); > +#else > at91_add_device_mmc(0,&cpuat91_mmc_data); > +#endif > /* I2C */ > at91_add_device_i2c(NULL, 0); > /* Platform devices */ > diff --git a/arch/arm/mach-at91/board-csb337.c b/arch/arm/mach-at91/board-csb337.c > index 1a1547b..36d65ef 100644 > --- a/arch/arm/mach-at91/board-csb337.c > +++ b/arch/arm/mach-at91/board-csb337.c > @@ -95,6 +95,15 @@ static struct at91_cf_data __initdata csb337_cf_data = { > .rst_pin = AT91_PIN_PD2, > }; > > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata csb337_mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PD5, > + .wp_pin = AT91_PIN_PD6, > + }, > +}; > +#else > static struct at91_mmc_data __initdata csb337_mmc_data = { > .det_pin = AT91_PIN_PD5, > .slot_b = 0, > @@ -102,6 +111,7 @@ static struct at91_mmc_data __initdata csb337_mmc_data = { > .wp_pin = AT91_PIN_PD6, > .vcc_pin = -EINVAL, > }; > +#endif > > static struct spi_board_info csb337_spi_devices[] = { > { /* CAN controller */ > @@ -244,7 +254,11 @@ static void __init csb337_board_init(void) > /* SPI */ > at91_add_device_spi(csb337_spi_devices, ARRAY_SIZE(csb337_spi_devices)); > /* MMC */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&csb337_mci0_data); > +#else > at91_add_device_mmc(0,&csb337_mmc_data); > +#endif > /* NOR flash */ > platform_device_register(&csb_flash); > /* LEDs */ > diff --git a/arch/arm/mach-at91/board-eb9200.c b/arch/arm/mach-at91/board-eb9200.c > index d302ca3..f374ecc 100644 > --- a/arch/arm/mach-at91/board-eb9200.c > +++ b/arch/arm/mach-at91/board-eb9200.c > @@ -83,6 +83,15 @@ static struct at91_cf_data __initdata eb9200_cf_data = { > .rst_pin = AT91_PIN_PC5, > }; > > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata eb9200_mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = -EINVAL, > + .wp_pin = -EINVAL, > + }, > +}; > +#else > static struct at91_mmc_data __initdata eb9200_mmc_data = { > .slot_b = 0, > .wire4 = 1, > @@ -90,6 +99,7 @@ static struct at91_mmc_data __initdata eb9200_mmc_data = { > .wp_pin = -EINVAL, > .vcc_pin = -EINVAL, > }; > +#endif > > static struct i2c_board_info __initdata eb9200_i2c_devices[] = { > { > @@ -116,7 +126,11 @@ static void __init eb9200_board_init(void) > at91_add_device_spi(NULL, 0); > /* MMC */ > /* only supports 1 or 4 bit interface, not wired through to SPI */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&eb9200_mci0_data); > +#else > at91_add_device_mmc(0,&eb9200_mmc_data); > +#endif > } > > MACHINE_START(ATEB9200, "Embest ATEB9200") > diff --git a/arch/arm/mach-at91/board-ecbat91.c b/arch/arm/mach-at91/board-ecbat91.c > index 69966ce..0f39fb3 100644 > --- a/arch/arm/mach-at91/board-ecbat91.c > +++ b/arch/arm/mach-at91/board-ecbat91.c > @@ -75,6 +75,15 @@ static struct at91_usbh_data __initdata ecb_at91usbh_data = { > .overcurrent_pin= {-EINVAL, -EINVAL}, > }; > > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata ecbat91_mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = -EINVAL, > + .wp_pin = -EINVAL, > + }, > +}; > +#else > static struct at91_mmc_data __initdata ecb_at91mmc_data = { > .slot_b = 0, > .wire4 = 1, > @@ -82,6 +91,7 @@ static struct at91_mmc_data __initdata ecb_at91mmc_data = { > .wp_pin = -EINVAL, > .vcc_pin = -EINVAL, > }; > +#endif > > > #if defined(CONFIG_MTD_DATAFLASH) > @@ -164,7 +174,11 @@ static void __init ecb_at91board_init(void) > at91_add_device_i2c(NULL, 0); > > /* MMC */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&ecbat91_mci0_data); > +#else > at91_add_device_mmc(0,&ecb_at91mmc_data); > +#endif > > /* SPI */ > at91_add_device_spi(ecb_at91spi_devices, ARRAY_SIZE(ecb_at91spi_devices)); > diff --git a/arch/arm/mach-at91/board-eco920.c b/arch/arm/mach-at91/board-eco920.c > index f23aabe..932bebd 100644 > --- a/arch/arm/mach-at91/board-eco920.c > +++ b/arch/arm/mach-at91/board-eco920.c > @@ -64,6 +64,15 @@ static struct at91_udc_data __initdata eco920_udc_data = { > .pullup_pin = AT91_PIN_PB13, > }; > > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata eco920_mci0_data = { > + .slot[0] = { > + .bus_width = 1, > + .detect_pin = -EINVAL, > + .wp_pin = -EINVAL, > + }, > +}; > +#else > static struct at91_mmc_data __initdata eco920_mmc_data = { > .slot_b = 0, > .wire4 = 0, > @@ -71,6 +80,7 @@ static struct at91_mmc_data __initdata eco920_mmc_data = { > .wp_pin = -EINVAL, > .vcc_pin = -EINVAL, > }; > +#endif > > static struct physmap_flash_data eco920_flash_data = { > .width = 2, > @@ -108,7 +118,11 @@ static void __init eco920_board_init(void) > at91_add_device_usbh(&eco920_usbh_data); > at91_add_device_udc(&eco920_udc_data); > > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&eco920_mci0_data); > +#else > at91_add_device_mmc(0,&eco920_mmc_data); > +#endif > platform_device_register(&eco920_flash); > > at91_ramc_write(0, AT91_SMC_CSR(7), AT91_SMC_RWHOLD_(1) > diff --git a/arch/arm/mach-at91/board-flexibity.c b/arch/arm/mach-at91/board-flexibity.c > index 1815152..6632a80 100644 > --- a/arch/arm/mach-at91/board-flexibity.c > +++ b/arch/arm/mach-at91/board-flexibity.c > @@ -80,6 +80,15 @@ static struct spi_board_info flexibity_spi_devices[] = { > }; > > /* MCI (SD/MMC) */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata flexibity_mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PC9, > + .wp_pin = AT91_PIN_PC4, > + }, > +}; > +#else > static struct at91_mmc_data __initdata flexibity_mmc_data = { > .slot_b = 0, > .wire4 = 1, > @@ -87,6 +96,7 @@ static struct at91_mmc_data __initdata flexibity_mmc_data = { > .wp_pin = AT91_PIN_PC4, > .vcc_pin = -EINVAL, > }; > +#endif > > /* LEDs */ > static struct gpio_led flexibity_leds[] = { > @@ -155,7 +165,11 @@ static void __init flexibity_board_init(void) > at91_add_device_spi(flexibity_spi_devices, > ARRAY_SIZE(flexibity_spi_devices)); > /* MMC */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&flexibity_mci0_data); > +#else > at91_add_device_mmc(0,&flexibity_mmc_data); > +#endif > /* LEDs */ > at91_gpio_leds(flexibity_leds, ARRAY_SIZE(flexibity_leds)); > } > diff --git a/arch/arm/mach-at91/board-foxg20.c b/arch/arm/mach-at91/board-foxg20.c > index caf017f..6cda303 100644 > --- a/arch/arm/mach-at91/board-foxg20.c > +++ b/arch/arm/mach-at91/board-foxg20.c > @@ -123,7 +123,7 @@ static struct at91_udc_data __initdata foxg20_udc_data = { > * SPI devices. > */ > static struct spi_board_info foxg20_spi_devices[] = { > -#if !defined(CONFIG_MMC_AT91) > +#if !defined(CONFIG_MMC_AT91)&& !defined(CONFIG_MMC_ATMELMCI) > { > .modalias = "mtd_dataflash", > .chip_select = 1, > @@ -146,6 +146,7 @@ static struct macb_platform_data __initdata foxg20_macb_data = { > * MCI (SD/MMC) > * det_pin, wp_pin and vcc_pin are not connected > */ > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > static struct at91_mmc_data __initdata foxg20_mmc_data = { > .slot_b = 1, > .wire4 = 1, > @@ -153,6 +154,15 @@ static struct at91_mmc_data __initdata foxg20_mmc_data = { > .wp_pin = -EINVAL, > .vcc_pin = -EINVAL, > }; > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata foxg20_mci0_data = { > + .slot[1] = { > + .bus_width = 4, > + .detect_pin = -EINVAL, > + .wp_pin = -EINVAL, > + }, > +}; > +#endif > > > /* > @@ -251,7 +261,11 @@ static void __init foxg20_board_init(void) > /* Ethernet */ > at91_add_device_eth(&foxg20_macb_data); > /* MMC */ > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > at91_add_device_mmc(0,&foxg20_mmc_data); > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&foxg20_mci0_data); > +#endif > /* I2C */ > at91_add_device_i2c(foxg20_i2c_devices, ARRAY_SIZE(foxg20_i2c_devices)); > /* LEDs */ > diff --git a/arch/arm/mach-at91/board-kb9202.c b/arch/arm/mach-at91/board-kb9202.c > index 59b92aa..e31ec8e 100644 > --- a/arch/arm/mach-at91/board-kb9202.c > +++ b/arch/arm/mach-at91/board-kb9202.c > @@ -86,6 +86,15 @@ static struct at91_udc_data __initdata kb9202_udc_data = { > .pullup_pin = AT91_PIN_PB22, > }; > > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata kb9202_mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PB2, > + .wp_pin = -EINVAL, > + }, > +}; > +#else > static struct at91_mmc_data __initdata kb9202_mmc_data = { > .det_pin = AT91_PIN_PB2, > .slot_b = 0, > @@ -93,6 +102,7 @@ static struct at91_mmc_data __initdata kb9202_mmc_data = { > .wp_pin = -EINVAL, > .vcc_pin = -EINVAL, > }; > +#endif > > static struct mtd_partition __initdata kb9202_nand_partition[] = { > { > @@ -124,7 +134,11 @@ static void __init kb9202_board_init(void) > /* USB Device */ > at91_add_device_udc(&kb9202_udc_data); > /* MMC */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&kb9202_mci0_data); > +#else > at91_add_device_mmc(0,&kb9202_mmc_data); > +#endif > /* I2C */ > at91_add_device_i2c(NULL, 0); > /* SPI */ > diff --git a/arch/arm/mach-at91/board-neocore926.c b/arch/arm/mach-at91/board-neocore926.c > index 57d5f6a..849b938 100644 > --- a/arch/arm/mach-at91/board-neocore926.c > +++ b/arch/arm/mach-at91/board-neocore926.c > @@ -146,12 +146,22 @@ static struct spi_board_info neocore926_spi_devices[] = { > /* > * MCI (SD/MMC) > */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata neocore926_mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PE18, > + .wp_pin = AT91_PIN_PE19, > + }, > +}; > +#else > static struct at91_mmc_data __initdata neocore926_mmc_data = { > .wire4 = 1, > .det_pin = AT91_PIN_PE18, > .wp_pin = AT91_PIN_PE19, > .vcc_pin = -EINVAL, > }; > +#endif > > > /* > @@ -357,7 +367,11 @@ static void __init neocore926_board_init(void) > neocore926_add_device_ts(); > > /* MMC */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&neocore926_mci0_data); > +#else > at91_add_device_mmc(1,&neocore926_mmc_data); > +#endif > > /* Ethernet */ > at91_add_device_eth(&neocore926_macb_data); > diff --git a/arch/arm/mach-at91/board-picotux200.c b/arch/arm/mach-at91/board-picotux200.c > index 59e35dd..a8cb032 100644 > --- a/arch/arm/mach-at91/board-picotux200.c > +++ b/arch/arm/mach-at91/board-picotux200.c > @@ -72,6 +72,15 @@ static struct at91_usbh_data __initdata picotux200_usbh_data = { > .overcurrent_pin= {-EINVAL, -EINVAL}, > }; > > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata picotux200_mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PB27, > + .wp_pin = AT91_PIN_PA17, > + }, > +}; > +#else > static struct at91_mmc_data __initdata picotux200_mmc_data = { > .det_pin = AT91_PIN_PB27, > .slot_b = 0, > @@ -79,6 +88,7 @@ static struct at91_mmc_data __initdata picotux200_mmc_data = { > .wp_pin = AT91_PIN_PA17, > .vcc_pin = -EINVAL, > }; > +#endif > > #define PICOTUX200_FLASH_BASE AT91_CHIPSELECT_0 > #define PICOTUX200_FLASH_SIZE SZ_4M > @@ -115,7 +125,11 @@ static void __init picotux200_board_init(void) > at91_add_device_i2c(NULL, 0); > /* MMC */ > at91_set_gpio_output(AT91_PIN_PB22, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&picotux200_mci0_data); > +#else > at91_add_device_mmc(0,&picotux200_mmc_data); > +#endif > /* NOR Flash */ > platform_device_register(&picotux200_flash); > } > diff --git a/arch/arm/mach-at91/board-qil-a9260.c b/arch/arm/mach-at91/board-qil-a9260.c > index b6ed5ed..2a49993 100644 > --- a/arch/arm/mach-at91/board-qil-a9260.c > +++ b/arch/arm/mach-at91/board-qil-a9260.c > @@ -173,6 +173,15 @@ static void __init ek_add_device_nand(void) > /* > * MCI (SD/MMC) > */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata ek_mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = -EINVAL, > + .wp_pin = -EINVAL, > + }, > +}; > +#else > static struct at91_mmc_data __initdata ek_mmc_data = { > .slot_b = 0, > .wire4 = 1, > @@ -180,6 +189,7 @@ static struct at91_mmc_data __initdata ek_mmc_data = { > .wp_pin = -EINVAL, > .vcc_pin = -EINVAL, > }; > +#endif > > /* > * GPIO Buttons > @@ -249,7 +259,11 @@ static void __init ek_board_init(void) > /* Ethernet */ > at91_add_device_eth(&ek_macb_data); > /* MMC */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&ek_mci0_data); > +#else > at91_add_device_mmc(0,&ek_mmc_data); > +#endif > /* Push Buttons */ > ek_add_device_buttons(); > /* LEDs */ > diff --git a/arch/arm/mach-at91/board-rm9200dk.c b/arch/arm/mach-at91/board-rm9200dk.c > index 01332aa..b6128fb 100644 > --- a/arch/arm/mach-at91/board-rm9200dk.c > +++ b/arch/arm/mach-at91/board-rm9200dk.c > @@ -90,6 +90,15 @@ static struct at91_cf_data __initdata dk_cf_data = { > }; > > #ifndef CONFIG_MTD_AT91_DATAFLASH_CARD > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata dk_mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = -EINVAL, > + .wp_pin = -EINVAL, > + }, > +}; > +#else > static struct at91_mmc_data __initdata dk_mmc_data = { > .slot_b = 0, > .wire4 = 1, > @@ -98,6 +107,7 @@ static struct at91_mmc_data __initdata dk_mmc_data = { > .vcc_pin = -EINVAL, > }; > #endif > +#endif > > static struct spi_board_info dk_spi_devices[] = { > { /* DataFlash chip */ > @@ -211,8 +221,12 @@ static void __init dk_board_init(void) > #else > /* MMC */ > at91_set_gpio_output(AT91_PIN_PB7, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&dk_mci0_data); > +#else > at91_add_device_mmc(0,&dk_mmc_data); > #endif > +#endif > /* NAND */ > at91_add_device_nand(&dk_nand_data); > /* NOR Flash */ > diff --git a/arch/arm/mach-at91/board-rm9200ek.c b/arch/arm/mach-at91/board-rm9200ek.c > index b2e4fe2..7177aac 100644 > --- a/arch/arm/mach-at91/board-rm9200ek.c > +++ b/arch/arm/mach-at91/board-rm9200ek.c > @@ -83,6 +83,7 @@ static struct at91_udc_data __initdata ek_udc_data = { > }; > > #ifndef CONFIG_MTD_AT91_DATAFLASH_CARD > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > static struct at91_mmc_data __initdata ek_mmc_data = { > .det_pin = AT91_PIN_PB27, > .slot_b = 0, > @@ -90,6 +91,15 @@ static struct at91_mmc_data __initdata ek_mmc_data = { > .wp_pin = AT91_PIN_PA17, > .vcc_pin = -EINVAL, > }; > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata ek_mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PB27, > + .wp_pin = AT91_PIN_PA17, > + } > +}; > +#endif > #endif > > static struct spi_board_info ek_spi_devices[] = { > @@ -180,7 +190,11 @@ static void __init ek_board_init(void) > #else > /* MMC */ > at91_set_gpio_output(AT91_PIN_PB22, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */ > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > at91_add_device_mmc(0,&ek_mmc_data); > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&ek_mci0_data); > +#endif > #endif > /* NOR Flash */ > platform_device_register(&ek_flash); > diff --git a/arch/arm/mach-at91/board-rsi-ews.c b/arch/arm/mach-at91/board-rsi-ews.c > index af0750f..373537a 100644 > --- a/arch/arm/mach-at91/board-rsi-ews.c > +++ b/arch/arm/mach-at91/board-rsi-ews.c > @@ -77,12 +77,22 @@ static struct at91_usbh_data rsi_ews_usbh_data __initdata = { > /* > * SD/MC > */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata rsi_ews_mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PB27, > + .wp_pin = AT91_PIN_PB29, > + }, > +}; > +#else > static struct at91_mmc_data rsi_ews_mmc_data __initdata = { > .slot_b = 0, > .wire4 = 1, > .det_pin = AT91_PIN_PB27, > .wp_pin = AT91_PIN_PB29, > }; > +#endif > > /* > * I2C > @@ -218,7 +228,11 @@ static void __init rsi_ews_board_init(void) > at91_add_device_spi(rsi_ews_spi_devices, > ARRAY_SIZE(rsi_ews_spi_devices)); > /* MMC */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&rsi_ews_mci0_data); > +#else > at91_add_device_mmc(0,&rsi_ews_mmc_data); > +#endif > /* NOR Flash */ > platform_device_register(&rsiews_nor_flash); > /* LEDs */ > diff --git a/arch/arm/mach-at91/board-sam9-l9260.c b/arch/arm/mach-at91/board-sam9-l9260.c > index e8b116b..7562011 100644 > --- a/arch/arm/mach-at91/board-sam9-l9260.c > +++ b/arch/arm/mach-at91/board-sam9-l9260.c > @@ -89,7 +89,7 @@ static struct at91_udc_data __initdata ek_udc_data = { > * SPI devices. > */ > static struct spi_board_info ek_spi_devices[] = { > -#if !defined(CONFIG_MMC_AT91) > +#if !defined(CONFIG_MMC_AT91)&& !defined(CONFIG_MMC_ATMELMCI) > { /* DataFlash chip */ > .modalias = "mtd_dataflash", > .chip_select = 1, > @@ -174,6 +174,15 @@ static void __init ek_add_device_nand(void) > /* > * MCI (SD/MMC) > */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata ek_mci0_data = { > + .slot[1] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PC8, > + .wp_pin = AT91_PIN_PC4, > + }, > +}; > +#else > static struct at91_mmc_data __initdata ek_mmc_data = { > .slot_b = 1, > .wire4 = 1, > @@ -181,6 +190,7 @@ static struct at91_mmc_data __initdata ek_mmc_data = { > .wp_pin = AT91_PIN_PC4, > .vcc_pin = -EINVAL, > }; > +#endif > > static void __init ek_board_init(void) > { > @@ -197,7 +207,11 @@ static void __init ek_board_init(void) > /* Ethernet */ > at91_add_device_eth(&ek_macb_data); > /* MMC */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&ek_mci0_data); > +#else > at91_add_device_mmc(0,&ek_mmc_data); > +#endif > /* I2C */ > at91_add_device_i2c(NULL, 0); > } > diff --git a/arch/arm/mach-at91/board-sam9260ek.c b/arch/arm/mach-at91/board-sam9260ek.c > index d5aec55..b39009e 100644 > --- a/arch/arm/mach-at91/board-sam9260ek.c > +++ b/arch/arm/mach-at91/board-sam9260ek.c > @@ -121,7 +121,7 @@ static void __init at73c213_set_clk(struct at73c213_board_info *info) {} > * SPI devices. > */ > static struct spi_board_info ek_spi_devices[] = { > -#if !defined(CONFIG_MMC_AT91) > +#if !defined(CONFIG_MMC_AT91)&& !defined(CONFIG_MMC_ATMELMCI) > { /* DataFlash chip */ > .modalias = "mtd_dataflash", > .chip_select = 1, > @@ -224,6 +224,15 @@ static void __init ek_add_device_nand(void) > /* > * MCI (SD/MMC) > */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata ek_mci0_data = { > + .slot[1] = { > + .bus_width = 4, > + .detect_pin = -EINVAL, > + .wp_pin = -EINVAL, > + }, > +}; > +#else > static struct at91_mmc_data __initdata ek_mmc_data = { > .slot_b = 1, > .wire4 = 1, > @@ -231,6 +240,7 @@ static struct at91_mmc_data __initdata ek_mmc_data = { > .wp_pin = -EINVAL, > .vcc_pin = -EINVAL, > }; > +#endif > > > /* > @@ -332,7 +342,11 @@ static void __init ek_board_init(void) > /* Ethernet */ > at91_add_device_eth(&ek_macb_data); > /* MMC */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&ek_mci0_data); > +#else > at91_add_device_mmc(0,&ek_mmc_data); > +#endif > /* I2C */ > at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices)); > /* SSC (to AT73C213) */ > diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c > index 065fed3..797dd7c 100644 > --- a/arch/arm/mach-at91/board-sam9261ek.c > +++ b/arch/arm/mach-at91/board-sam9261ek.c > @@ -344,6 +344,7 @@ static struct spi_board_info ek_spi_devices[] = { > #else /* CONFIG_SPI_ATMEL_* */ > /* spi0 and mmc/sd share the same PIO pins: cannot be used at the same time */ > > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > /* > * MCI (SD/MMC) > * det_pin, wp_pin and vcc_pin are not connected > @@ -354,6 +355,15 @@ static struct at91_mmc_data __initdata ek_mmc_data = { > .wp_pin = -EINVAL, > .vcc_pin = -EINVAL, > }; > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = -EINVAL, > + .wp_pin = -EINVAL, > + }, > +}; > +#endif > > #endif /* CONFIG_SPI_ATMEL_* */ > > @@ -601,7 +611,11 @@ static void __init ek_board_init(void) > at91_add_device_ssc(AT91SAM9261_ID_SSC1, ATMEL_SSC_TX); > #else > /* MMC */ > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > at91_add_device_mmc(0,&ek_mmc_data); > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&mci0_data); > +#endif > #endif > /* LCD Controller */ > at91_add_device_lcdc(&ek_lcdc_data); > diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c > index 2ffe50f..419c57a 100644 > --- a/arch/arm/mach-at91/board-sam9263ek.c > +++ b/arch/arm/mach-at91/board-sam9263ek.c > @@ -149,12 +149,22 @@ static struct spi_board_info ek_spi_devices[] = { > /* > * MCI (SD/MMC) > */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata mci1_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PE18, > + .wp_pin = AT91_PIN_PE19, > + }, > +}; > +#else > static struct at91_mmc_data __initdata ek_mmc_data = { > .wire4 = 1, > .det_pin = AT91_PIN_PE18, > .wp_pin = AT91_PIN_PE19, > .vcc_pin = -EINVAL, > }; > +#endif > > > /* > @@ -423,7 +433,11 @@ static void __init ek_board_init(void) > /* Touchscreen */ > ek_add_device_ts(); > /* MMC */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(1,&mci1_data); > +#else > at91_add_device_mmc(1,&ek_mmc_data); > +#endif > /* Ethernet */ > at91_add_device_eth(&ek_macb_data); > /* NAND */ > diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c > index b109ce2..bb06521 100644 > --- a/arch/arm/mach-at91/board-sam9rlek.c > +++ b/arch/arm/mach-at91/board-sam9rlek.c > @@ -64,12 +64,22 @@ static struct usba_platform_data __initdata ek_usba_udc_data = { > /* > * MCI (SD/MMC) > */ > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > static struct at91_mmc_data __initdata ek_mmc_data = { > .wire4 = 1, > .det_pin = AT91_PIN_PA15, > .wp_pin = -EINVAL, > .vcc_pin = -EINVAL, > }; > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PA15, > + .wp_pin = -EINVAL, > + }, > +}; > +#endif > > > /* > @@ -306,7 +316,11 @@ static void __init ek_board_init(void) > /* SPI */ > at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); > /* MMC */ > +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) > at91_add_device_mmc(0,&ek_mmc_data); > +#elif defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&mci0_data); > +#endif > /* LCD Controller */ > at91_add_device_lcdc(&ek_lcdc_data); > /* AC97 */ > diff --git a/arch/arm/mach-at91/board-usb-a926x.c b/arch/arm/mach-at91/board-usb-a926x.c > index b7483a3..879e34e 100644 > --- a/arch/arm/mach-at91/board-usb-a926x.c > +++ b/arch/arm/mach-at91/board-usb-a926x.c > @@ -114,7 +114,7 @@ static struct mmc_spi_platform_data at91_mmc_spi_pdata = { > * SPI devices. > */ > static struct spi_board_info usb_a9263_spi_devices[] = { > -#if !defined(CONFIG_MMC_AT91) > +#if !defined(CONFIG_MMC_AT91)&& !defined(CONFIG_MMC_ATMELMCI) > { /* DataFlash chip */ > .modalias = "mtd_dataflash", > .chip_select = 0, > diff --git a/arch/arm/mach-at91/board-yl-9200.c b/arch/arm/mach-at91/board-yl-9200.c > index 38dd279..3d3b8a6 100644 > --- a/arch/arm/mach-at91/board-yl-9200.c > +++ b/arch/arm/mach-at91/board-yl-9200.c > @@ -138,12 +138,22 @@ static struct at91_udc_data __initdata yl9200_udc_data = { > /* > * MMC > */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > +static struct mci_platform_data __initdata yl9200_mci0_data = { > + .slot[0] = { > + .bus_width = 4, > + .detect_pin = AT91_PIN_PB9, > + .wp_pin = -EINVAL, > + }, > +}; > +#else > static struct at91_mmc_data __initdata yl9200_mmc_data = { > .det_pin = AT91_PIN_PB9, > .wire4 = 1, > .wp_pin = -EINVAL, > .vcc_pin = -EINVAL, > }; > +#endif > > /* > * NAND Flash > @@ -571,7 +581,11 @@ static void __init yl9200_board_init(void) > /* I2C */ > at91_add_device_i2c(yl9200_i2c_devices, ARRAY_SIZE(yl9200_i2c_devices)); > /* MMC */ > +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) > + at91_add_device_mci(0,&yl9200_mci0_data); > +#else > at91_add_device_mmc(0,&yl9200_mmc_data); > +#endif > /* NAND */ > at91_add_device_nand(&yl9200_nand_data); > /* NOR Flash */ ^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: [PATCH v2] ARM: at91: add atmel-mci support for chips and boards which can use it 2012-05-21 10:23 ` ludovic.desroches at atmel.com @ 2012-05-28 7:41 ` Jean-Christophe PLAGNIOL-VILLARD -1 siblings, 0 replies; 28+ messages in thread From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-05-28 7:41 UTC (permalink / raw) To: ludovic.desroches; +Cc: linux-mmc, linux-arm-kernel, nicolas.ferre On 12:23 Mon 21 May , ludovic.desroches@atmel.com wrote: > From: Ludovic Desroches <ludovic.desroches@atmel.com> > > Since atmel-mci driver supports all atmel mci version excepted the rm9200 one, > use it instead of at91_mci driver. > > Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> > --- > V2: add several boards I missed for the 9g20 and 9260 please drop the old driver support too for calao bord you can do it too Best Regards, J. ^ permalink raw reply [flat|nested] 28+ messages in thread
* [PATCH v2] ARM: at91: add atmel-mci support for chips and boards which can use it @ 2012-05-28 7:41 ` Jean-Christophe PLAGNIOL-VILLARD 0 siblings, 0 replies; 28+ messages in thread From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-05-28 7:41 UTC (permalink / raw) To: linux-arm-kernel On 12:23 Mon 21 May , ludovic.desroches at atmel.com wrote: > From: Ludovic Desroches <ludovic.desroches@atmel.com> > > Since atmel-mci driver supports all atmel mci version excepted the rm9200 one, > use it instead of at91_mci driver. > > Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> > --- > V2: add several boards I missed for the 9g20 and 9260 please drop the old driver support too for calao bord you can do it too Best Regards, J. ^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: [PATCH v2] ARM: at91: add atmel-mci support for chips and boards which can use it 2012-05-28 7:41 ` Jean-Christophe PLAGNIOL-VILLARD @ 2012-05-29 10:56 ` Nicolas Ferre -1 siblings, 0 replies; 28+ messages in thread From: Nicolas Ferre @ 2012-05-29 10:56 UTC (permalink / raw) To: Jean-Christophe PLAGNIOL-VILLARD Cc: ludovic.desroches, linux-mmc, linux-arm-kernel On 05/28/2012 09:41 AM, Jean-Christophe PLAGNIOL-VILLARD : > On 12:23 Mon 21 May , ludovic.desroches@atmel.com wrote: >> From: Ludovic Desroches <ludovic.desroches@atmel.com> >> >> Since atmel-mci driver supports all atmel mci version excepted the rm9200 one, >> use it instead of at91_mci driver. >> >> Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> >> --- >> V2: add several boards I missed > for the 9g20 and 9260 please drop the old driver support too No, we will drop the support for old driver when we finish the transition period. We will then drop at91_mci with all configuration data in device/board files. > for calao bord you can do it too Well, you can add it yourself. As you may be able to test it, it sounds better if you handle this part... Bye, -- Nicolas Ferre ^ permalink raw reply [flat|nested] 28+ messages in thread
* [PATCH v2] ARM: at91: add atmel-mci support for chips and boards which can use it @ 2012-05-29 10:56 ` Nicolas Ferre 0 siblings, 0 replies; 28+ messages in thread From: Nicolas Ferre @ 2012-05-29 10:56 UTC (permalink / raw) To: linux-arm-kernel On 05/28/2012 09:41 AM, Jean-Christophe PLAGNIOL-VILLARD : > On 12:23 Mon 21 May , ludovic.desroches at atmel.com wrote: >> From: Ludovic Desroches <ludovic.desroches@atmel.com> >> >> Since atmel-mci driver supports all atmel mci version excepted the rm9200 one, >> use it instead of at91_mci driver. >> >> Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> >> --- >> V2: add several boards I missed > for the 9g20 and 9260 please drop the old driver support too No, we will drop the support for old driver when we finish the transition period. We will then drop at91_mci with all configuration data in device/board files. > for calao bord you can do it too Well, you can add it yourself. As you may be able to test it, it sounds better if you handle this part... Bye, -- Nicolas Ferre ^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: [PATCH v2] ARM: at91: add atmel-mci support for chips and boards which can use it 2012-05-29 10:56 ` Nicolas Ferre @ 2012-05-29 15:57 ` Jean-Christophe PLAGNIOL-VILLARD -1 siblings, 0 replies; 28+ messages in thread From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-05-29 15:57 UTC (permalink / raw) To: Nicolas Ferre; +Cc: ludovic.desroches, linux-mmc, linux-arm-kernel On 12:56 Tue 29 May , Nicolas Ferre wrote: > On 05/28/2012 09:41 AM, Jean-Christophe PLAGNIOL-VILLARD : > > On 12:23 Mon 21 May , ludovic.desroches@atmel.com wrote: > >> From: Ludovic Desroches <ludovic.desroches@atmel.com> > >> > >> Since atmel-mci driver supports all atmel mci version excepted the rm9200 one, > >> use it instead of at91_mci driver. > >> > >> Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> > >> --- > >> V2: add several boards I missed > > for the 9g20 and 9260 please drop the old driver support too > > No, we will drop the support for old driver when we finish the > transition period. We will then drop at91_mci with all configuration > data in device/board files. on 9g20 and 9260 the new drivers is present for release there is no reason to keep one more release Best Regards, J. ^ permalink raw reply [flat|nested] 28+ messages in thread
* [PATCH v2] ARM: at91: add atmel-mci support for chips and boards which can use it @ 2012-05-29 15:57 ` Jean-Christophe PLAGNIOL-VILLARD 0 siblings, 0 replies; 28+ messages in thread From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-05-29 15:57 UTC (permalink / raw) To: linux-arm-kernel On 12:56 Tue 29 May , Nicolas Ferre wrote: > On 05/28/2012 09:41 AM, Jean-Christophe PLAGNIOL-VILLARD : > > On 12:23 Mon 21 May , ludovic.desroches at atmel.com wrote: > >> From: Ludovic Desroches <ludovic.desroches@atmel.com> > >> > >> Since atmel-mci driver supports all atmel mci version excepted the rm9200 one, > >> use it instead of at91_mci driver. > >> > >> Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> > >> --- > >> V2: add several boards I missed > > for the 9g20 and 9260 please drop the old driver support too > > No, we will drop the support for old driver when we finish the > transition period. We will then drop at91_mci with all configuration > data in device/board files. on 9g20 and 9260 the new drivers is present for release there is no reason to keep one more release Best Regards, J. ^ permalink raw reply [flat|nested] 28+ messages in thread
end of thread, other threads:[~2012-05-29 15:57 UTC | newest] Thread overview: 28+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2012-05-16 15:51 [PATCH 0/2] ARM: at91: allow all boards to use atmel-mci driver ludovic.desroches 2012-05-16 15:51 ` ludovic.desroches at atmel.com 2012-05-16 15:51 ` [PATCH 1/2] ARM: at91: add atmel-mci support for chips and boards which can use it ludovic.desroches 2012-05-16 15:51 ` ludovic.desroches at atmel.com 2012-05-21 10:17 ` Nicolas Ferre 2012-05-21 10:17 ` Nicolas Ferre 2012-05-16 15:51 ` [PATCH 2/2] mmc: at91-mci: this driver is now deprecated ludovic.desroches 2012-05-16 15:51 ` ludovic.desroches at atmel.com 2012-05-17 12:45 ` Chris Ball 2012-05-17 12:45 ` Chris Ball 2012-05-17 18:28 ` ludovic.desroches 2012-05-17 18:28 ` ludovic.desroches 2012-05-17 18:36 ` Chris Ball 2012-05-17 18:36 ` Chris Ball 2012-05-17 18:40 ` ludovic.desroches 2012-05-17 18:40 ` ludovic.desroches 2012-05-21 10:19 ` Nicolas Ferre 2012-05-21 10:19 ` Nicolas Ferre 2012-05-21 10:23 ` [PATCH v2] ARM: at91: add atmel-mci support for chips and boards which can use it ludovic.desroches 2012-05-21 10:23 ` ludovic.desroches at atmel.com 2012-05-21 10:31 ` ludovic.desroches 2012-05-21 10:31 ` ludovic.desroches 2012-05-28 7:41 ` Jean-Christophe PLAGNIOL-VILLARD 2012-05-28 7:41 ` Jean-Christophe PLAGNIOL-VILLARD 2012-05-29 10:56 ` Nicolas Ferre 2012-05-29 10:56 ` Nicolas Ferre 2012-05-29 15:57 ` Jean-Christophe PLAGNIOL-VILLARD 2012-05-29 15:57 ` Jean-Christophe PLAGNIOL-VILLARD
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.