* [ALSA - driver 0001347]: unable to configure sound card
@ 2006-04-13 16:08 bugtrack
0 siblings, 0 replies; 13+ messages in thread
From: bugtrack @ 2006-04-13 16:08 UTC (permalink / raw)
To: alsa-devel
The following issue has been CLOSED
======================================================================
<https://bugtrack.alsa-project.org/alsa-bug/view.php?id=1347>
======================================================================
Reported By: CptS
Assigned To: tiwai
======================================================================
Project: ALSA - driver
Issue ID: 1347
Category: PCI - nm256
Reproducibility: always
Severity: major
Priority: normal
Status: closed
Distribution: Knoppix 4.0
Kernel Version: 2.6.11
Resolution: open
Fixed in Version:
======================================================================
Date Submitted: 08-17-2005 11:05 CEST
Last Modified: 04-13-2006 18:08 CEST
======================================================================
Summary: unable to configure sound card
Description:
I'm having problems configuring my sound card with alsa, here are the
details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??I'm having problems configuring my sound card with
alsa, here are the details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??I'm having problems configuring my sound card with
alsa, here are the details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??
======================================================================
----------------------------------------------------------------------
CptS - 04-13-06 17:42
----------------------------------------------------------------------
I didn't try with alsa cvs, but the hardware on that laptop is quite old so
I won't upgrade to newer versions on debian so i guess OSS will be just
fine for what it's used for.
thanks anyways.
Shay.
p.s. this thread is pretty old, i've been using the laptop with the oss
coniguration and kernel 2.4 for a long time now.
----------------------------------------------------------------------
rlrevell - 04-13-06 18:08
----------------------------------------------------------------------
AFAICT there's no bug
Issue History
Date Modified Username Field Change
======================================================================
08-17-05 11:05 CptS New Issue
08-17-05 11:05 CptS Distribution => Knoppix 4.0
08-17-05 11:05 CptS Kernel Version => 2.6.11
08-17-05 11:24 CptS Note Added: 0005835
08-20-05 19:48 CptS Issue Monitored: CptS
08-20-05 19:50 CptS Note Added: 0005883
08-20-05 20:32 rlrevell Note Added: 0005884
08-20-05 20:37 rlrevell Note Added: 0005885
08-22-05 22:00 CptS Note Added: 0005901
08-23-05 16:40 tiwai Note Added: 0005908
09-07-05 21:33 dcooppan Note Added: 0006066
03-16-06 08:01 rlrevell Note Added: 0008588
03-19-06 23:42 CptS Note Added: 0008699
03-20-06 01:26 rlrevell Note Added: 0008701
04-13-06 17:42 CptS Note Added: 0009264
04-13-06 18:08 rlrevell Status assigned => closed
04-13-06 18:08 rlrevell Note Added: 0009266
======================================================================
-------------------------------------------------------
This SF.Net email is sponsored by xPML, a groundbreaking scripting language
that extends applications into web and mobile media. Attend the live webcast
and join the prime developer group breaking into this new coding territory!
http://sel.as-us.falkag.net/sel?cmd=lnk&kid=110944&bid=241720&dat=121642
^ permalink raw reply [flat|nested] 13+ messages in thread* [ALSA - driver 0001347]: unable to configure sound card
@ 2006-04-13 15:42 bugtrack
0 siblings, 0 replies; 13+ messages in thread
From: bugtrack @ 2006-04-13 15:42 UTC (permalink / raw)
To: alsa-devel
A NOTE has been added to this issue.
======================================================================
<https://bugtrack.alsa-project.org/alsa-bug/view.php?id=1347>
======================================================================
Reported By: CptS
Assigned To: tiwai
======================================================================
Project: ALSA - driver
Issue ID: 1347
Category: PCI - nm256
Reproducibility: always
Severity: major
Priority: normal
Status: assigned
Distribution: Knoppix 4.0
Kernel Version: 2.6.11
======================================================================
Date Submitted: 08-17-2005 11:05 CEST
Last Modified: 04-13-2006 17:42 CEST
======================================================================
Summary: unable to configure sound card
Description:
I'm having problems configuring my sound card with alsa, here are the
details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??I'm having problems configuring my sound card with
alsa, here are the details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??I'm having problems configuring my sound card with
alsa, here are the details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??
======================================================================
----------------------------------------------------------------------
rlrevell - 03-20-06 01:26
----------------------------------------------------------------------
That's not possible, OSS will eventually be removed from the kernel.
If it works with the OSS sb16 model it should work with the ALSA snd-sb16
driver.
Maybe you can try again with ALSA CVS and the snd-nm256 driver - the bug
causing it to lock up the system was recently fixed.
----------------------------------------------------------------------
CptS - 04-13-06 17:42
----------------------------------------------------------------------
I didn't try with alsa cvs, but the hardware on that laptop is quite old so
I won't upgrade to newer versions on debian so i guess OSS will be just
fine for what it's used for.
thanks anyways.
Shay.
p.s. this thread is pretty old, i've been using the laptop with the oss
coniguration and kernel 2.4 for a long time now.
Issue History
Date Modified Username Field Change
======================================================================
08-17-05 11:05 CptS New Issue
08-17-05 11:05 CptS Distribution => Knoppix 4.0
08-17-05 11:05 CptS Kernel Version => 2.6.11
08-17-05 11:24 CptS Note Added: 0005835
08-20-05 19:48 CptS Issue Monitored: CptS
08-20-05 19:50 CptS Note Added: 0005883
08-20-05 20:32 rlrevell Note Added: 0005884
08-20-05 20:37 rlrevell Note Added: 0005885
08-22-05 22:00 CptS Note Added: 0005901
08-23-05 16:40 tiwai Note Added: 0005908
09-07-05 21:33 dcooppan Note Added: 0006066
03-16-06 08:01 rlrevell Note Added: 0008588
03-19-06 23:42 CptS Note Added: 0008699
03-20-06 01:26 rlrevell Note Added: 0008701
04-13-06 17:42 CptS Note Added: 0009264
======================================================================
-------------------------------------------------------
This SF.Net email is sponsored by xPML, a groundbreaking scripting language
that extends applications into web and mobile media. Attend the live webcast
and join the prime developer group breaking into this new coding territory!
http://sel.as-us.falkag.net/sel?cmd=lnk&kid=110944&bid=241720&dat=121642
^ permalink raw reply [flat|nested] 13+ messages in thread* [ALSA - driver 0001347]: unable to configure sound card
@ 2006-03-20 0:26 bugtrack
0 siblings, 0 replies; 13+ messages in thread
From: bugtrack @ 2006-03-20 0:26 UTC (permalink / raw)
To: alsa-devel
A NOTE has been added to this issue.
======================================================================
<https://bugtrack.alsa-project.org/alsa-bug/view.php?id=1347>
======================================================================
Reported By: CptS
Assigned To: tiwai
======================================================================
Project: ALSA - driver
Issue ID: 1347
Category: PCI - nm256
Reproducibility: always
Severity: major
Priority: normal
Status: assigned
Distribution: Knoppix 4.0
Kernel Version: 2.6.11
======================================================================
Date Submitted: 08-17-2005 11:05 CEST
Last Modified: 03-20-2006 01:26 CET
======================================================================
Summary: unable to configure sound card
Description:
I'm having problems configuring my sound card with alsa, here are the
details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??I'm having problems configuring my sound card with
alsa, here are the details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??I'm having problems configuring my sound card with
alsa, here are the details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??
======================================================================
----------------------------------------------------------------------
CptS - 03-19-06 23:42
----------------------------------------------------------------------
No improvements with later alsa, but oss made it work using sb16 module and
the kind help of people from #ubuntu. i suggets you ditch alsa on this
hardware and use oss.
----------------------------------------------------------------------
rlrevell - 03-20-06 01:26
----------------------------------------------------------------------
That's not possible, OSS will eventually be removed from the kernel.
If it works with the OSS sb16 model it should work with the ALSA snd-sb16
driver.
Maybe you can try again with ALSA CVS and the snd-nm256 driver - the bug
causing it to lock up the system was recently fixed.
Issue History
Date Modified Username Field Change
======================================================================
08-17-05 11:05 CptS New Issue
08-17-05 11:05 CptS Distribution => Knoppix 4.0
08-17-05 11:05 CptS Kernel Version => 2.6.11
08-17-05 11:24 CptS Note Added: 0005835
08-20-05 19:48 CptS Issue Monitored: CptS
08-20-05 19:50 CptS Note Added: 0005883
08-20-05 20:32 rlrevell Note Added: 0005884
08-20-05 20:37 rlrevell Note Added: 0005885
08-22-05 22:00 CptS Note Added: 0005901
08-23-05 16:40 tiwai Note Added: 0005908
09-07-05 21:33 dcooppan Note Added: 0006066
03-16-06 08:01 rlrevell Note Added: 0008588
03-19-06 23:42 CptS Note Added: 0008699
03-20-06 01:26 rlrevell Note Added: 0008701
======================================================================
-------------------------------------------------------
This SF.Net email is sponsored by xPML, a groundbreaking scripting language
that extends applications into web and mobile media. Attend the live webcast
and join the prime developer group breaking into this new coding territory!
http://sel.as-us.falkag.net/sel?cmd=lnk&kid=110944&bid=241720&dat=121642
^ permalink raw reply [flat|nested] 13+ messages in thread* [ALSA - driver 0001347]: unable to configure sound card
@ 2006-03-19 22:42 bugtrack
0 siblings, 0 replies; 13+ messages in thread
From: bugtrack @ 2006-03-19 22:42 UTC (permalink / raw)
To: alsa-devel
A NOTE has been added to this issue.
======================================================================
<https://bugtrack.alsa-project.org/alsa-bug/view.php?id=1347>
======================================================================
Reported By: CptS
Assigned To: tiwai
======================================================================
Project: ALSA - driver
Issue ID: 1347
Category: PCI - nm256
Reproducibility: always
Severity: major
Priority: normal
Status: assigned
Distribution: Knoppix 4.0
Kernel Version: 2.6.11
======================================================================
Date Submitted: 08-17-2005 11:05 CEST
Last Modified: 03-19-2006 23:42 CET
======================================================================
Summary: unable to configure sound card
Description:
I'm having problems configuring my sound card with alsa, here are the
details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??I'm having problems configuring my sound card with
alsa, here are the details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??I'm having problems configuring my sound card with
alsa, here are the details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??
======================================================================
----------------------------------------------------------------------
rlrevell - 03-16-06 08:01
----------------------------------------------------------------------
Any improvement with later ALSA versions?
----------------------------------------------------------------------
CptS - 03-19-06 23:42
----------------------------------------------------------------------
No improvements with later alsa, but oss made it work using sb16 module and
the kind help of people from #ubuntu. i suggets you ditch alsa on this
hardware and use oss.
Issue History
Date Modified Username Field Change
======================================================================
08-17-05 11:05 CptS New Issue
08-17-05 11:05 CptS Distribution => Knoppix 4.0
08-17-05 11:05 CptS Kernel Version => 2.6.11
08-17-05 11:24 CptS Note Added: 0005835
08-20-05 19:48 CptS Issue Monitored: CptS
08-20-05 19:50 CptS Note Added: 0005883
08-20-05 20:32 rlrevell Note Added: 0005884
08-20-05 20:37 rlrevell Note Added: 0005885
08-22-05 22:00 CptS Note Added: 0005901
08-23-05 16:40 tiwai Note Added: 0005908
09-07-05 21:33 dcooppan Note Added: 0006066
03-16-06 08:01 rlrevell Note Added: 0008588
03-19-06 23:42 CptS Note Added: 0008699
======================================================================
-------------------------------------------------------
This SF.Net email is sponsored by xPML, a groundbreaking scripting language
that extends applications into web and mobile media. Attend the live webcast
and join the prime developer group breaking into this new coding territory!
http://sel.as-us.falkag.net/sel?cmd=lnk&kid=110944&bid=241720&dat=121642
^ permalink raw reply [flat|nested] 13+ messages in thread* [ALSA - driver 0001347]: unable to configure sound card
@ 2006-03-16 7:01 bugtrack
0 siblings, 0 replies; 13+ messages in thread
From: bugtrack @ 2006-03-16 7:01 UTC (permalink / raw)
To: alsa-devel
A NOTE has been added to this issue.
======================================================================
<https://bugtrack.alsa-project.org/alsa-bug/view.php?id=1347>
======================================================================
Reported By: CptS
Assigned To: tiwai
======================================================================
Project: ALSA - driver
Issue ID: 1347
Category: PCI - nm256
Reproducibility: always
Severity: major
Priority: normal
Status: assigned
Distribution: Knoppix 4.0
Kernel Version: 2.6.11
======================================================================
Date Submitted: 08-17-2005 11:05 CEST
Last Modified: 03-16-2006 08:01 CET
======================================================================
Summary: unable to configure sound card
Description:
I'm having problems configuring my sound card with alsa, here are the
details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??I'm having problems configuring my sound card with
alsa, here are the details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??I'm having problems configuring my sound card with
alsa, here are the details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??
======================================================================
----------------------------------------------------------------------
dcooppan - 09-07-05 21:33
----------------------------------------------------------------------
I have the exact same problem: ALSA from FC4:2.6.11-1.1369_FC4 kernel
Hardware is Compaq 1920 laptop with NeoMagic sound card
>From dmesg one sees:
>>>>>>>>>>>>>>>>>>>>>>>>
PCI: Found IRQ 10 for device 0000:01:00.1
PCI: Sharing IRQ 10 with 0000:00:07.2
nm256: no ac97 is found!
force the driver to load by passing in the module parameter
force_ac97=1
or try sb16 or cs423x drivers instead.
NeoMagic 256: probe of 0000:01:00.1 failed with error -6
pnp: Device 00:01.01 activated.
>>>>>>>>>>>>>>>>>>>>>>>>
Can some check out what error -6 means. I confirm that if you use option
force_ac97=1 then the system will HANG! Only option is power-off.
I am very interested to get this working so please copy me at
dcooppan@comcast.net
BTW: I also tried 2.4 with OSS, nada, nothing, same problem, even tried
loading
snd_cs4236 driver and get:
>>>>>>>>>>>>>>
[root@dellcpx dcooppan]# modprobe snd-cs4236
FATAL: Error inserting snd_cs4236
(/lib/modules/2.6.11-1.1369_FC4/kernel/sound/isa/cs423x/snd-cs4236.ko): No
such device
>>>>>>>>>>>>>>>>>>>
thanks much
----------------------------------------------------------------------
rlrevell - 03-16-06 08:01
----------------------------------------------------------------------
Any improvement with later ALSA versions?
Issue History
Date Modified Username Field Change
======================================================================
08-17-05 11:05 CptS New Issue
08-17-05 11:05 CptS Distribution => Knoppix 4.0
08-17-05 11:05 CptS Kernel Version => 2.6.11
08-17-05 11:24 CptS Note Added: 0005835
08-20-05 19:48 CptS Issue Monitored: CptS
08-20-05 19:50 CptS Note Added: 0005883
08-20-05 20:32 rlrevell Note Added: 0005884
08-20-05 20:37 rlrevell Note Added: 0005885
08-22-05 22:00 CptS Note Added: 0005901
08-23-05 16:40 tiwai Note Added: 0005908
09-07-05 21:33 dcooppan Note Added: 0006066
03-16-06 08:01 rlrevell Note Added: 0008588
======================================================================
-------------------------------------------------------
This SF.Net email is sponsored by xPML, a groundbreaking scripting language
that extends applications into web and mobile media. Attend the live webcast
and join the prime developer group breaking into this new coding territory!
http://sel.as-us.falkag.net/sel?cmd=lnk&kid=110944&bid=241720&dat=121642
^ permalink raw reply [flat|nested] 13+ messages in thread* [ALSA - driver 0001347]: unable to configure sound card
@ 2005-09-07 19:33 bugtrack
0 siblings, 0 replies; 13+ messages in thread
From: bugtrack @ 2005-09-07 19:33 UTC (permalink / raw)
To: alsa-devel
A NOTE has been added to this issue.
======================================================================
<https://bugtrack.alsa-project.org/alsa-bug/view.php?id=1347>
======================================================================
Reported By: CptS
Assigned To: tiwai
======================================================================
Project: ALSA - driver
Issue ID: 1347
Category: PCI - nm256
Reproducibility: always
Severity: major
Priority: normal
Status: assigned
Distribution: Knoppix 4.0
Kernel Version: 2.6.11
======================================================================
Date Submitted: 08-17-2005 11:05 CEST
Last Modified: 09-07-2005 21:33 CEST
======================================================================
Summary: unable to configure sound card
Description:
I'm having problems configuring my sound card with alsa, here are the
details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??I'm having problems configuring my sound card with
alsa, here are the details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??I'm having problems configuring my sound card with
alsa, here are the details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??
======================================================================
----------------------------------------------------------------------
tiwai - 08-23-05 16:40
----------------------------------------------------------------------
I guess this laptop has no nm256 ac97 but it's connected to cs4236 codec
internally. Check your BIOS setting and try snd-cs4236 driver.
----------------------------------------------------------------------
dcooppan - 09-07-05 21:33
----------------------------------------------------------------------
I have the exact same problem: ALSA from FC4:2.6.11-1.1369_FC4 kernel
Hardware is Compaq 1920 laptop with NeoMagic sound card
>From dmesg one sees:
>>>>>>>>>>>>>>>>>>>>>>>>
PCI: Found IRQ 10 for device 0000:01:00.1
PCI: Sharing IRQ 10 with 0000:00:07.2
nm256: no ac97 is found!
force the driver to load by passing in the module parameter
force_ac97=1
or try sb16 or cs423x drivers instead.
NeoMagic 256: probe of 0000:01:00.1 failed with error -6
pnp: Device 00:01.01 activated.
>>>>>>>>>>>>>>>>>>>>>>>>
Can some check out what error -6 means. I confirm that if you use option
force_ac97=1 then the system will HANG! Only option is power-off.
I am very interested to get this working so please copy me at
dcooppan@comcast.net
BTW: I also tried 2.4 with OSS, nada, nothing, same problem, even tried
loading
snd_cs4236 driver and get:
>>>>>>>>>>>>>>
[root@dellcpx dcooppan]# modprobe snd-cs4236
FATAL: Error inserting snd_cs4236
(/lib/modules/2.6.11-1.1369_FC4/kernel/sound/isa/cs423x/snd-cs4236.ko): No
such device
>>>>>>>>>>>>>>>>>>>
thanks much
Issue History
Date Modified Username Field Change
======================================================================
08-17-05 11:05 CptS New Issue
08-17-05 11:05 CptS Distribution => Knoppix 4.0
08-17-05 11:05 CptS Kernel Version => 2.6.11
08-17-05 11:24 CptS Note Added: 0005835
08-20-05 19:48 CptS Issue Monitored: CptS
08-20-05 19:50 CptS Note Added: 0005883
08-20-05 20:32 rlrevell Note Added: 0005884
08-20-05 20:37 rlrevell Note Added: 0005885
08-22-05 22:00 CptS Note Added: 0005901
08-23-05 16:40 tiwai Note Added: 0005908
09-07-05 21:33 dcooppan Note Added: 0006066
======================================================================
-------------------------------------------------------
SF.Net email is Sponsored by the Better Software Conference & EXPO
September 19-22, 2005 * San Francisco, CA * Development Lifecycle Practices
Agile & Plan-Driven Development * Managing Projects & Teams * Testing & QA
Security * Process Improvement & Measurement * http://www.sqe.com/bsce5sf
^ permalink raw reply [flat|nested] 13+ messages in thread* [ALSA - driver 0001347]: unable to configure sound card
@ 2005-08-23 14:40 bugtrack
0 siblings, 0 replies; 13+ messages in thread
From: bugtrack @ 2005-08-23 14:40 UTC (permalink / raw)
To: alsa-devel
A NOTE has been added to this issue.
======================================================================
<https://bugtrack.alsa-project.org/alsa-bug/view.php?id=1347>
======================================================================
Reported By: CptS
Assigned To: tiwai
======================================================================
Project: ALSA - driver
Issue ID: 1347
Category: PCI - nm256
Reproducibility: always
Severity: major
Priority: normal
Status: assigned
Distribution: Knoppix 4.0
Kernel Version: 2.6.11
======================================================================
Date Submitted: 08-17-2005 11:05 CEST
Last Modified: 08-23-2005 16:40 CEST
======================================================================
Summary: unable to configure sound card
Description:
I'm having problems configuring my sound card with alsa, here are the
details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??I'm having problems configuring my sound card with
alsa, here are the details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??I'm having problems configuring my sound card with
alsa, here are the details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??
======================================================================
----------------------------------------------------------------------
CptS - 08-22-05 22:00
----------------------------------------------------------------------
It crashed = the system just stopped responding. no report found later in
the logs. if you have any ways of logging the crash i'd be happy to hear.
I didn't paste the bug 3 times... i just added 2 notes to the same bug.
S.
----------------------------------------------------------------------
tiwai - 08-23-05 16:40
----------------------------------------------------------------------
I guess this laptop has no nm256 ac97 but it's connected to cs4236 codec
internally. Check your BIOS setting and try snd-cs4236 driver.
Issue History
Date Modified Username Field Change
======================================================================
08-17-05 11:05 CptS New Issue
08-17-05 11:05 CptS Distribution => Knoppix 4.0
08-17-05 11:05 CptS Kernel Version => 2.6.11
08-17-05 11:24 CptS Note Added: 0005835
08-20-05 19:48 CptS Issue Monitored: CptS
08-20-05 19:50 CptS Note Added: 0005883
08-20-05 20:32 rlrevell Note Added: 0005884
08-20-05 20:37 rlrevell Note Added: 0005885
08-22-05 22:00 CptS Note Added: 0005901
08-23-05 16:40 tiwai Note Added: 0005908
======================================================================
-------------------------------------------------------
SF.Net email is Sponsored by the Better Software Conference & EXPO
September 19-22, 2005 * San Francisco, CA * Development Lifecycle Practices
Agile & Plan-Driven Development * Managing Projects & Teams * Testing & QA
Security * Process Improvement & Measurement * http://www.sqe.com/bsce5sf
^ permalink raw reply [flat|nested] 13+ messages in thread* [ALSA - driver 0001347]: unable to configure sound card
@ 2005-08-22 20:00 bugtrack
0 siblings, 0 replies; 13+ messages in thread
From: bugtrack @ 2005-08-22 20:00 UTC (permalink / raw)
To: alsa-devel
A NOTE has been added to this issue.
======================================================================
<https://bugtrack.alsa-project.org/alsa-bug/view.php?id=1347>
======================================================================
Reported By: CptS
Assigned To: tiwai
======================================================================
Project: ALSA - driver
Issue ID: 1347
Category: PCI - nm256
Reproducibility: always
Severity: major
Priority: normal
Status: assigned
Distribution: Knoppix 4.0
Kernel Version: 2.6.11
======================================================================
Date Submitted: 08-17-2005 11:05 CEST
Last Modified: 08-22-2005 22:00 CEST
======================================================================
Summary: unable to configure sound card
Description:
I'm having problems configuring my sound card with alsa, here are the
details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??I'm having problems configuring my sound card with
alsa, here are the details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??I'm having problems configuring my sound card with
alsa, here are the details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??
======================================================================
----------------------------------------------------------------------
rlrevell - 08-20-05 20:37
----------------------------------------------------------------------
You also pasted the same bug report three times which makes it a little
less likely that you'll get a response.
----------------------------------------------------------------------
CptS - 08-22-05 22:00
----------------------------------------------------------------------
It crashed = the system just stopped responding. no report found later in
the logs. if you have any ways of logging the crash i'd be happy to hear.
I didn't paste the bug 3 times... i just added 2 notes to the same bug.
S.
Issue History
Date Modified Username Field Change
======================================================================
08-17-05 11:05 CptS New Issue
08-17-05 11:05 CptS Distribution => Knoppix 4.0
08-17-05 11:05 CptS Kernel Version => 2.6.11
08-17-05 11:24 CptS Note Added: 0005835
08-20-05 19:48 CptS Issue Monitored: CptS
08-20-05 19:50 CptS Note Added: 0005883
08-20-05 20:32 rlrevell Note Added: 0005884
08-20-05 20:37 rlrevell Note Added: 0005885
08-22-05 22:00 CptS Note Added: 0005901
======================================================================
-------------------------------------------------------
SF.Net email is Sponsored by the Better Software Conference & EXPO
September 19-22, 2005 * San Francisco, CA * Development Lifecycle Practices
Agile & Plan-Driven Development * Managing Projects & Teams * Testing & QA
Security * Process Improvement & Measurement * http://www.sqe.com/bsce5sf
^ permalink raw reply [flat|nested] 13+ messages in thread* [ALSA - driver 0001347]: unable to configure sound card
@ 2005-08-20 18:37 bugtrack
0 siblings, 0 replies; 13+ messages in thread
From: bugtrack @ 2005-08-20 18:37 UTC (permalink / raw)
To: alsa-devel
A NOTE has been added to this issue.
======================================================================
<https://bugtrack.alsa-project.org/alsa-bug/view.php?id=1347>
======================================================================
Reported By: CptS
Assigned To: tiwai
======================================================================
Project: ALSA - driver
Issue ID: 1347
Category: PCI - nm256
Reproducibility: always
Severity: major
Priority: normal
Status: assigned
Distribution: Knoppix 4.0
Kernel Version: 2.6.11
======================================================================
Date Submitted: 08-17-2005 11:05 CEST
Last Modified: 08-20-2005 20:37 CEST
======================================================================
Summary: unable to configure sound card
Description:
I'm having problems configuring my sound card with alsa, here are the
details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??I'm having problems configuring my sound card with
alsa, here are the details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??I'm having problems configuring my sound card with
alsa, here are the details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??
======================================================================
----------------------------------------------------------------------
rlrevell - 08-20-05 20:32
----------------------------------------------------------------------
Because you didn't provide enough detail.
"I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)"
What do you mean by "it crashed"? What exactly happened? You mean a
kernel Oops? How about posting the output?
----------------------------------------------------------------------
rlrevell - 08-20-05 20:37
----------------------------------------------------------------------
You also pasted the same bug report three times which makes it a little
less likely that you'll get a response.
Issue History
Date Modified Username Field Change
======================================================================
08-17-05 11:05 CptS New Issue
08-17-05 11:05 CptS Distribution => Knoppix 4.0
08-17-05 11:05 CptS Kernel Version => 2.6.11
08-17-05 11:24 CptS Note Added: 0005835
08-20-05 19:48 CptS Issue Monitored: CptS
08-20-05 19:50 CptS Note Added: 0005883
08-20-05 20:32 rlrevell Note Added: 0005884
08-20-05 20:37 rlrevell Note Added: 0005885
======================================================================
-------------------------------------------------------
SF.Net email is Sponsored by the Better Software Conference & EXPO
September 19-22, 2005 * San Francisco, CA * Development Lifecycle Practices
Agile & Plan-Driven Development * Managing Projects & Teams * Testing & QA
Security * Process Improvement & Measurement * http://www.sqe.com/bsce5sf
^ permalink raw reply [flat|nested] 13+ messages in thread* [ALSA - driver 0001347]: unable to configure sound card
@ 2005-08-20 18:32 bugtrack
0 siblings, 0 replies; 13+ messages in thread
From: bugtrack @ 2005-08-20 18:32 UTC (permalink / raw)
To: alsa-devel
A NOTE has been added to this issue.
======================================================================
<https://bugtrack.alsa-project.org/alsa-bug/view.php?id=1347>
======================================================================
Reported By: CptS
Assigned To: tiwai
======================================================================
Project: ALSA - driver
Issue ID: 1347
Category: PCI - nm256
Reproducibility: always
Severity: major
Priority: normal
Status: assigned
Distribution: Knoppix 4.0
Kernel Version: 2.6.11
======================================================================
Date Submitted: 08-17-2005 11:05 CEST
Last Modified: 08-20-2005 20:32 CEST
======================================================================
Summary: unable to configure sound card
Description:
I'm having problems configuring my sound card with alsa, here are the
details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??I'm having problems configuring my sound card with
alsa, here are the details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??I'm having problems configuring my sound card with
alsa, here are the details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??
======================================================================
----------------------------------------------------------------------
CptS - 08-20-05 19:50
----------------------------------------------------------------------
Is anybody monitoring this forum ?? Please, i need help ASAP!
----------------------------------------------------------------------
rlrevell - 08-20-05 20:32
----------------------------------------------------------------------
Because you didn't provide enough detail.
"I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)"
What do you mean by "it crashed"? What exactly happened? You mean a
kernel Oops? How about posting the output?
Issue History
Date Modified Username Field Change
======================================================================
08-17-05 11:05 CptS New Issue
08-17-05 11:05 CptS Distribution => Knoppix 4.0
08-17-05 11:05 CptS Kernel Version => 2.6.11
08-17-05 11:24 CptS Note Added: 0005835
08-20-05 19:48 CptS Issue Monitored: CptS
08-20-05 19:50 CptS Note Added: 0005883
08-20-05 20:32 rlrevell Note Added: 0005884
======================================================================
-------------------------------------------------------
SF.Net email is Sponsored by the Better Software Conference & EXPO
September 19-22, 2005 * San Francisco, CA * Development Lifecycle Practices
Agile & Plan-Driven Development * Managing Projects & Teams * Testing & QA
Security * Process Improvement & Measurement * http://www.sqe.com/bsce5sf
^ permalink raw reply [flat|nested] 13+ messages in thread* [ALSA - driver 0001347]: unable to configure sound card
@ 2005-08-20 17:50 bugtrack
0 siblings, 0 replies; 13+ messages in thread
From: bugtrack @ 2005-08-20 17:50 UTC (permalink / raw)
To: alsa-devel
A NOTE has been added to this issue.
======================================================================
<https://bugtrack.alsa-project.org/alsa-bug/view.php?id=1347>
======================================================================
Reported By: CptS
Assigned To: tiwai
======================================================================
Project: ALSA - driver
Issue ID: 1347
Category: PCI - nm256
Reproducibility: always
Severity: major
Priority: normal
Status: assigned
Distribution: Knoppix 4.0
Kernel Version: 2.6.11
======================================================================
Date Submitted: 08-17-2005 11:05 CEST
Last Modified: 08-20-2005 19:50 CEST
======================================================================
Summary: unable to configure sound card
Description:
I'm having problems configuring my sound card with alsa, here are the
details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??I'm having problems configuring my sound card with
alsa, here are the details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??I'm having problems configuring my sound card with
alsa, here are the details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??
======================================================================
----------------------------------------------------------------------
CptS - 08-17-05 11:24
----------------------------------------------------------------------
ps. I've read the other PCI nm256 issues and found 2 identical threads, the
problem is that they are un-resolved... Please HELP! (i can't afford a new
laptop :))
----------------------------------------------------------------------
CptS - 08-20-05 19:50
----------------------------------------------------------------------
Is anybody monitoring this forum ?? Please, i need help ASAP!
Issue History
Date Modified Username Field Change
======================================================================
08-17-05 11:05 CptS New Issue
08-17-05 11:05 CptS Distribution => Knoppix 4.0
08-17-05 11:05 CptS Kernel Version => 2.6.11
08-17-05 11:24 CptS Note Added: 0005835
08-20-05 19:48 CptS Issue Monitored: CptS
08-20-05 19:50 CptS Note Added: 0005883
======================================================================
-------------------------------------------------------
SF.Net email is Sponsored by the Better Software Conference & EXPO
September 19-22, 2005 * San Francisco, CA * Development Lifecycle Practices
Agile & Plan-Driven Development * Managing Projects & Teams * Testing & QA
Security * Process Improvement & Measurement * http://www.sqe.com/bsce5sf
^ permalink raw reply [flat|nested] 13+ messages in thread* [ALSA - driver 0001347]: unable to configure sound card
@ 2005-08-17 9:24 bugtrack
0 siblings, 0 replies; 13+ messages in thread
From: bugtrack @ 2005-08-17 9:24 UTC (permalink / raw)
To: alsa-devel
A NOTE has been added to this issue.
======================================================================
<https://bugtrack.alsa-project.org/alsa-bug/view.php?id=1347>
======================================================================
Reported By: CptS
Assigned To: tiwai
======================================================================
Project: ALSA - driver
Issue ID: 1347
Category: PCI - nm256
Reproducibility: always
Severity: major
Priority: normal
Status: assigned
Distribution: Knoppix 4.0
Kernel Version: 2.6.11
======================================================================
Date Submitted: 08-17-2005 11:05 CEST
Last Modified: 08-17-2005 11:24 CEST
======================================================================
Summary: unable to configure sound card
Description:
I'm having problems configuring my sound card with alsa, here are the
details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??I'm having problems configuring my sound card with
alsa, here are the details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??I'm having problems configuring my sound card with
alsa, here are the details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??
======================================================================
----------------------------------------------------------------------
CptS - 08-17-05 11:24
----------------------------------------------------------------------
ps. I've read the other PCI nm256 issues and found 2 identical threads, the
problem is that they are un-resolved... Please HELP! (i can't afford a new
laptop :))
Issue History
Date Modified Username Field Change
======================================================================
08-17-05 11:05 CptS New Issue
08-17-05 11:05 CptS Distribution => Knoppix 4.0
08-17-05 11:05 CptS Kernel Version => 2.6.11
08-17-05 11:24 CptS Note Added: 0005835
======================================================================
-------------------------------------------------------
SF.Net email is Sponsored by the Better Software Conference & EXPO
September 19-22, 2005 * San Francisco, CA * Development Lifecycle Practices
Agile & Plan-Driven Development * Managing Projects & Teams * Testing & QA
Security * Process Improvement & Measurement * http://www.sqe.com/bsce5sf
^ permalink raw reply [flat|nested] 13+ messages in thread* [ALSA - driver 0001347]: unable to configure sound card
@ 2005-08-17 9:05 bugtrack
0 siblings, 0 replies; 13+ messages in thread
From: bugtrack @ 2005-08-17 9:05 UTC (permalink / raw)
To: alsa-devel
The following issue has been SUBMITTED.
======================================================================
<https://bugtrack.alsa-project.org/alsa-bug/view.php?id=1347>
======================================================================
Reported By: CptS
Assigned To: tiwai
======================================================================
Project: ALSA - driver
Issue ID: 1347
Category: PCI - nm256
Reproducibility: always
Severity: major
Priority: normal
Status: assigned
Distribution: Knoppix 4.0
Kernel Version: 2.6.11
======================================================================
Date Submitted: 08-17-2005 11:05 CEST
Last Modified: 08-17-2005 11:05 CEST
======================================================================
Summary: unable to configure sound card
Description:
I'm having problems configuring my sound card with alsa, here are the
details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??I'm having problems configuring my sound card with
alsa, here are the details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??I'm having problems configuring my sound card with
alsa, here are the details:
the sound card is NeoMagic 256AV (NM2200) located onboard a Compaq
Presario 1920.
I'm currently running Knoppix 4.0 hdd installed (kernel 2.6)
here's lspci -vv outputs on the cards:
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
Subsystem: Compaq Computer Corporation MagicMedia 256AV Audio
Device on Durango
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f4800000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
I wouldn't have addressed you unless I've already tried everything:
I've tried the solution of the same problem regarding HP Omni 4150 with
the same card.
I used alsaconf and it tried to load snd-nm256, after loading it crashed,
dmesg suggested loading it with force_ac97=1 switch but once i did it the
system crashed (on 3 differet linux installations)
I did a legacy scan using alsaconf for all legacy drivers.
I 'modprobe'ed for hours on every imaginable option (ad1848, sb, cs423x,
etc..)
I've edited the modules.conf and manually defined the dma and irq
I removed alsa completly and re-install it.
I had debian with 2.4 kernel installed and i've upgraded to 2.6
I changed the distro from debian to Knoppix (kinda same thing but...)
anyway, you get the point..
can you please assist??
======================================================================
Issue History
Date Modified Username Field Change
======================================================================
08-17-05 11:05 CptS New Issue
08-17-05 11:05 CptS Distribution => Knoppix 4.0
08-17-05 11:05 CptS Kernel Version => 2.6.11
======================================================================
-------------------------------------------------------
SF.Net email is Sponsored by the Better Software Conference & EXPO
September 19-22, 2005 * San Francisco, CA * Development Lifecycle Practices
Agile & Plan-Driven Development * Managing Projects & Teams * Testing & QA
Security * Process Improvement & Measurement * http://www.sqe.com/bsce5sf
^ permalink raw reply [flat|nested] 13+ messages in thread
end of thread, other threads:[~2006-04-13 16:08 UTC | newest]
Thread overview: 13+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2006-04-13 16:08 [ALSA - driver 0001347]: unable to configure sound card bugtrack
-- strict thread matches above, loose matches on Subject: below --
2006-04-13 15:42 bugtrack
2006-03-20 0:26 bugtrack
2006-03-19 22:42 bugtrack
2006-03-16 7:01 bugtrack
2005-09-07 19:33 bugtrack
2005-08-23 14:40 bugtrack
2005-08-22 20:00 bugtrack
2005-08-20 18:37 bugtrack
2005-08-20 18:32 bugtrack
2005-08-20 17:50 bugtrack
2005-08-17 9:24 bugtrack
2005-08-17 9:05 bugtrack
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.