* P3041DS: SATA SCSI disk gives errors
@ 2015-05-22 8:25 Siva Borra
2015-05-25 10:55 ` Luo Zhenhua
0 siblings, 1 reply; 4+ messages in thread
From: Siva Borra @ 2015-05-22 8:25 UTC (permalink / raw)
To: meta-freescale; +Cc: Adrian Dudau
Hello,
With latest dizzy branch of meta-fsl-ppc, with revision
(linux-qoriq_3.12.bb and linux-qoriq_3.12-prt.bb, Linux SRCREV =
"6619b8b55796cdf0cec04b66a71288edd3057229")
Instead of recognizing the HDD attached at SATA, it gives the following
errors.
[ 2.153541] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x1)
[ 6.800430] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x1)
[ 7.822380] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x1)
[ 11.966438] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x1)
[ 13.489386] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x1)
Same feature works fine with 3.0.xx kernel supplied with board. Please
suggest how to fix this issue?
Regards,
Siva Borra.
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: P3041DS: SATA SCSI disk gives errors
2015-05-22 8:25 P3041DS: SATA SCSI disk gives errors Siva Borra
@ 2015-05-25 10:55 ` Luo Zhenhua
2015-05-25 12:18 ` Siva Borra
0 siblings, 1 reply; 4+ messages in thread
From: Luo Zhenhua @ 2015-05-25 10:55 UTC (permalink / raw)
To: Siva Borra, meta-freescale@yoctoproject.org; +Cc: Adrian Dudau
[-- Attachment #1: Type: text/plain, Size: 1717 bytes --]
Hello Siva,
I tried the dizzy branch to build images and boot p3041ds board (uImage, dtb, core-image-mininal.rootfs.ext2.gz.u-boot), the SATA is launched normally.
Layers commit:
Poky - dizzy:9c4ff467f66428488b1cd9798066a8cb5d6b4c3b
meta-openembedded - dizzy:5b6f39ce325d490fc382d5d59c5b8b9d5fa38b38
meta-fsl-ppc - dizzy:5eeeb3ad74b72d904f805bc6e248e93e722b45c4
The full boot log is attached.
Best Regards,
Zhenhua
> -----Original Message-----
> From: meta-freescale-bounces@yoctoproject.org [mailto:meta-freescale-
> bounces@yoctoproject.org] On Behalf Of Siva Borra
> Sent: Friday, May 22, 2015 4:26 PM
> To: meta-freescale@yoctoproject.org
> Cc: Adrian Dudau
> Subject: [meta-freescale] P3041DS: SATA SCSI disk gives errors
>
> Hello,
>
> With latest dizzy branch of meta-fsl-ppc, with revision (linux-qoriq_3.12.bb and
> linux-qoriq_3.12-prt.bb, Linux SRCREV =
> "6619b8b55796cdf0cec04b66a71288edd3057229")
> Instead of recognizing the HDD attached at SATA, it gives the following errors.
>
> [ 2.153541] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x1) [ 6.800430]
> ata1.00: failed to IDENTIFY (I/O error, err_mask=0x1) [ 7.822380] ata2.00: failed
> to IDENTIFY (I/O error, err_mask=0x1) [ 11.966438] ata1.00: failed to IDENTIFY
> (I/O error, err_mask=0x1) [ 13.489386] ata2.00: failed to IDENTIFY (I/O error,
> err_mask=0x1)
>
> Same feature works fine with 3.0.xx kernel supplied with board. Please suggest
> how to fix this issue?
>
> Regards,
> Siva Borra.
>
> --
> _______________________________________________
> meta-freescale mailing list
> meta-freescale@yoctoproject.org
> https://lists.yoctoproject.org/listinfo/meta-freescale
[-- Attachment #2: p3041ds.log --]
[-- Type: application/octet-stream, Size: 37137 bytes --]
=> tftp 1000000 b19537/p3041ds/uImage
Using e1000#0 device
TFTP from server 192.168.2.1; our IP address is 192.168.2.79
Filename 'b19537/p3041ds/uImage'.
Load address: 0x1000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
##########################################################
5.8 MiB/s
done
Bytes transferred = 4289288 (417308 hex)
=> tftp 2000000 b19537/p3041ds/dtb
Using e1000#0 device
TFTP from server 192.168.2.1; our IP address is 192.168.2.79
Filename 'b19537/p3041ds/dtb'.
Load address: 0x2000000
Loading: #######
3 MiB/s
done
Bytes transferred = 34545 (86f1 hex)
=> tftp 4000000 b19537/p3041ds/rootfs
Using e1000#0 device
TFTP from server 192.168.2.1; our IP address is 192.168.2.79
Filename 'b19537/p3041ds/rootfs'.
Load address: 0x4000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#############################################
5.7 MiB/s
done
Bytes transferred = 2888311 (2c1277 hex)
=> bootm 1000000 4000000 2000000
WARNING: adjusting available memory to 30000000
## Booting kernel from Legacy Image at 01000000 ...
Image Name: Linux-3.12.19-rt30-1.7.2+g6619b8
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 4289224 Bytes = 4.1 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 04000000 ...
Image Name: core-image-minimal-p3041ds-20150
Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
Data Size: 2888247 Bytes = 2.8 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 02000000
Booting using the fdt blob at 0x2000000
Uncompressing Kernel Image ... OK
Loading Ramdisk to 2fd3e000, end 2ffff237 ... OK
Loading Device Tree to 03fe4000, end 03fff6f0 ... OK
Using CoreNet Generic machine description
Memory CAM mapping: 256/256/256 Mb, residual: 1280Mb
Linux version 3.12.19-rt30-1.7.2+g6619b8b (b19537@right) (gcc version 4.9.1 (GCC) ) #1 SMP Mon May 25 04:33:13 CDT 2015
Found initrd at 0xefd3e000:0xeffff237
No /soc@ffe000000/qman@318000 property 'fsl,qman-fqd', using memblock_alloc(0000000000400000)
No /soc@ffe000000/qman@318000 property 'fsl,qman-pfdr', using memblock_alloc(0000000002000000)
Qman ver:0a01,01,02,00
No /soc@ffe000000/bman@31a000 property 'fsl,bman-fbpr', using memblock_alloc(0000000001000000)
Bman ver:0a02,01,00
pme: No /soc@ffe000000/pme@316000 property 'fsl,pme-pdsr', using memblock_alloc(0x0000000001000000)
pme: No /soc@ffe000000/pme@316000 property 'fsl,pme-sre', using memblock_alloc(0x0000000000a00000)
No USDPAA memory, no 'usdpaa_mem' bootarg
CPU maps initialized for 1 thread per core
bootconsole [udbg0] enabled
setup_arch: bootmem
CoreNet Generic board from Freescale Semiconductor
arch: exit
Zone ranges:
DMA [mem 0x00000000-0x2fffffff]
Normal empty
HighMem [mem 0x30000000-0x7fffffff]
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x00000000-0x7fffffff]
MMU: Allocated 1088 bytes of context maps for 255 contexts
PERCPU: Embedded 8 pages/cpu @c1969000 s9792 r8192 d14784 u32768
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 522752
Kernel command line:
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Sorting __ex_table...
Memory: 1921256K/2097152K available (6728K kernel code, 332K rwdata, 1776K rodata, 272K init, 452K bss, 175896K reserved, 1310712K highmem)
Kernel virtual memory layout:
* 0xfff5f000..0xfffff000 : fixmap
* 0xffc00000..0xffe00000 : highmem PTEs
* 0xffbfb000..0xffc00000 : early ioremap
* 0xf1000000..0xffbfb000 : vmalloc & ioremap
Hierarchical RCU implementation.
RCU debugfs-based tracing is enabled.
RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
NR_IRQS:512 nr_irqs:512 16
mpic: Setting up MPIC " OpenPIC " version 1.2 at ffe040000, max 4 CPUs
mpic: ISU size: 512, shift: 9, mask: 1ff
mpic: Initializing for 512 sources
clocksource: timebase mult[2aaaaaab] shift[24] registered
Console: colour dummy device 80x25
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
mpic: requesting IPIs...
e500 family performance monitor hardware support registered
Brought up 4 CPUs
devtmpfs: initialized
NET: Registered protocol family 16
Found FSL PCI host bridge at 0x0000000ffe200000. Firmware bus number: 0->1
PCI host bridge /pcie@ffe200000 ranges:
MEM 0x0000000c00000000..0x0000000c1fffffff -> 0x00000000e0000000
IO 0x0000000ff8000000..0x0000000ff800ffff -> 0x0000000000000000
/pcie@ffe200000: PCICSRBAR @ 0xdf000000
EDAC PCI0: Giving out device to module 'MPC85xx_edac' controller 'mpc85xx_pci_err': DEV 'ffe200000.pcie' (INTERRUPT)
MPC85xx_edac acquired irq 482 for PCI Err
MPC85xx_edac PCI err registered
Found FSL PCI host bridge at 0x0000000ffe202000. Firmware bus number: 0->1
PCI host bridge /pcie@ffe202000 ranges:
MEM 0x0000000c40000000..0x0000000c5fffffff -> 0x00000000e0000000
IO 0x0000000ff8020000..0x0000000ff802ffff -> 0x0000000000000000
/pcie@ffe202000: PCICSRBAR @ 0xdf000000
EDAC PCI1: Giving out device to module 'MPC85xx_edac' controller 'mpc85xx_pci_err': DEV 'ffe202000.pcie' (INTERRUPT)
MPC85xx_edac acquired irq 480 for PCI Err
MPC85xx_edac PCI err registered
PCI: Probing PCI hardware
fsl-pci ffe200000.pcie: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [io 0xf1040000-0xf104ffff] (bus address [0x0000-0xffff])
pci_bus 0000:00: root bus resource [mem 0xc00000000-0xc1fffffff] (bus address [0xe0000000-0xffffffff])
pci_bus 0000:00: root bus resource [bus 00-ff]
pci 0000:00:00.0: ignoring class 0x0b2000 (doesn't match header type 01)
pci 0000:00:00.0: PCI bridge to [bus 01-ff]
fsl-pci ffe202000.pcie: PCI host bridge to bus 0001:02
pci_bus 0001:02: root bus resource [io 0xf1060000-0xf106ffff] (bus address [0x0000-0xffff])
pci_bus 0001:02: root bus resource [mem 0xc40000000-0xc5fffffff] (bus address [0xe0000000-0xffffffff])
pci_bus 0001:02: root bus resource [bus 02-ff]
pci 0001:02:00.0: ignoring class 0x0b2000 (doesn't match header type 01)
pci 0001:02:00.0: Primary bus is hard wired to 0
pci 0001:02:00.0: bridge configuration invalid ([bus 01-01]), reconfiguring
pci 0001:02:00.0: PCI bridge to [bus 03-ff]
pci 0000:00:00.0: BAR 9: can't assign mem pref (size 0x100000)
pci 0000:01:00.0: BAR 6: assigned [mem 0xc00040000-0xc0007ffff pref]
pci 0000:00:00.0: PCI bridge to [bus 01]
pci 0000:00:00.0: bridge window [io 0xf1040000-0xf104ffff]
pci 0000:00:00.0: bridge window [mem 0xc00000000-0xc1fffffff]
pci_bus 0000:00: Some PCI device resources are unassigned, try booting with pci=realloc
pci 0001:02:00.0: BAR 9: can't assign mem pref (size 0x100000)
pci 0001:03:00.0: BAR 6: assigned [mem 0xc40080000-0xc400fffff pref]
pci 0001:02:00.0: PCI bridge to [bus 03]
pci 0001:02:00.0: bridge window [io 0xf1060000-0xf106ffff]
pci 0001:02:00.0: bridge window [mem 0xc40000000-0xc5fffffff]
pci_bus 0001:02: Some PCI device resources are unassigned, try booting with pci=realloc
bio: create slab <bio-0> at 0
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Bman err interrupt handler present
Bman portal initialised, cpu 0
Bman portal initialised, cpu 1
Bman portal initialised, cpu 2
Bman portal initialised, cpu 3
Bman portals initialised
Qman err interrupt handler present
Qman portal initialised, cpu 0
Qman portal initialised, cpu 1
Qman portal initialised, cpu 2
Qman portal initialised, cpu 3
Qman portals initialised
Bman: BPID allocator includes range 32:32
Qman: FQID allocator includes range 256:256
Qman: FQID allocator includes range 32768:32768
Qman: CGRID allocator includes range 0:256
Qman: pool channel allocator includes range 33:15
Switched to clocksource timebase
NET: Registered protocol family 2
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP: reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 2820K (efd3e000 - effff000)
audit: initializing netlink socket (disabled)
type=2000 audit(0.340:1): initialized
bounce pool size: 64 pages
HugeTLB registered 1 MB page size, pre-allocated 0 pages
HugeTLB registered 4 MB page size, pre-allocated 0 pages
HugeTLB registered 16 MB page size, pre-allocated 0 pages
HugeTLB registered 64 MB page size, pre-allocated 0 pages
HugeTLB registered 256 MB page size, pre-allocated 0 pages
HugeTLB registered 1 GB page size, pre-allocated 0 pages
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
NTFS driver 2.1.30 [Flags: R/O].
jffs2: version 2.2. (NAND) 2001-2006 Red Hat, Inc.
msgmni has been set to 1326
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0xffe11c500 (irq = 36, base_baud = 23437499) is a 16550A
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
serial8250.0: ttyS1 at MMIO 0xffe11c600 (irq = 36, base_baud = 23437499) is a 16550A
serial8250.0: ttyS2 at MMIO 0xffe11d500 (irq = 37, base_baud = 23437499) is a 16550A
serial8250.0: ttyS3 at MMIO 0xffe11d600 (irq = 37, base_baud = 23437499) is a 16550A
ePAPR hypervisor byte channel driver
Generic non-volatile memory driver v1.1
brd: module loaded
loop: module loaded
st: Version 20101219, fixed bufsize 32768, s/g segs 256
fsl-sata ffe220000.sata: Sata FSL Platform/CSB Driver init
scsi0 : sata_fsl
ata1: SATA max UDMA/133 irq 68
fsl-sata ffe221000.sata: Sata FSL Platform/CSB Driver init
scsi1 : sata_fsl
ata2: SATA max UDMA/133 irq 69
scsi2 : sata_sil24
scsi3 : sata_sil24
ata3: SATA max UDMA/100 host m128@0xc40000000 port 0xc40004000 irq 42
ata4: SATA max UDMA/100 host m128@0xc40000000 port 0xc40006000 irq 42
fe8000000.flash: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002801
Amd/Fujitsu Extended Query Table at 0x0040
Amd/Fujitsu Extended Query version 1.3.
number of CFI chips: 1
ONFI param page 0 valid
ONFI flash detected
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xdc (Micron MT29F4G08ABADAWP), 512MiB, page size: 2048, OOB size: 64
Bad block table found at page 262080, version 0x01
Bad block table found at page 262016, version 0x01
6 ofpart partitions found on MTD device fffa00000.flash
Creating 6 MTD partitions on "fffa00000.flash":
0x000000000000-0x000002000000 : "NAND U-Boot Image"
0x000002000000-0x000012000000 : "NAND Root File System"
0x000012000000-0x00001a000000 : "NAND Compressed RFS Image"
0x00001a000000-0x00001e000000 : "NAND Linux Kernel Image"
0x00001e000000-0x00001f000000 : "NAND DTB Image"
0x00001f000000-0x000040000000 : "NAND Writable User area"
mtd: partition "NAND Writable User area" extends beyond the end of device "fffa00000.flash" -- size truncated to 0x1000000
eLBC NAND device at 0xfffa00000, bank 2
fsl_espi ffe110000.spi: master is unqueued, this is deprecated
m25p80 spi32766.0: found s25fl129p1, expected s25sl12801
m25p80 spi32766.0: s25fl129p1 (16384 Kbytes)
4 ofpart partitions found on MTD device spi32766.0
Creating 4 MTD partitions on "spi32766.0":
0x000000000000-0x000000100000 : "u-boot"
0x000000100000-0x000000600000 : "kernel"
0x000000600000-0x000000700000 : "dtb"
0x000000700000-0x000001000000 : "file system"
fsl_espi ffe110000.spi: at 0xf116e000 (irq = 53)
libphy: Fixed MDIO Bus: probed
mdio-mux-mmioreg fffdf0009.mdio-mux-emi1: failed to register mdio-mux bus /localbus@ffe124000/board-control@3,0/mdio-mux-emi1
platform fffdf0009.mdio-mux-emi1: Driver mdio-mux-mmioreg requests probe deferral
libphy: Freescale PowerQUICC MII Bus: probed
libphy: Freescale XGMAC MDIO Bus: probed
mdio_bus ffe4f1000: MDIO read error
mdio_bus ffe4f1000: MDIO read error
mdio_bus ffe4f1000: MDIO read error
mdio_bus ffe4f1000: MDIO read error
mdio_bus ffe4f1000: cannot get PHY at address 4
Freescale FM module (May 25 2015:04:32:35), FMD API version 21.1.0
Freescale FM Ports module (May 25 2015:04:32:39)
dpaa_debugfs: FSL DPAA Ethernet debugfs entries ()
dpaa_generic_debugfs: FSL DPAA Ethernet debugfs entries ()
fsl_mac: fsl_mac: FSL FMan MAC API based driver ()
fsl_mac ffe4e0000.ethernet: FMan dTSEC version: 0x08240101
fsl_mac ffe4e0000.ethernet: FMan MAC address: 00:e0:0c:00:3b:00
fsl_mac ffe4e2000.ethernet: FMan dTSEC version: 0x08240101
fsl_mac ffe4e2000.ethernet: FMan MAC address: 00:e0:0c:00:3b:01
fsl_mac ffe4e4000.ethernet: FMan dTSEC version: 0x08240101
fsl_mac ffe4e4000.ethernet: FMan MAC address: 00:e0:0c:00:3b:02
fsl_mac ffe4e6000.ethernet: FMan dTSEC version: 0x08240101
fsl_mac ffe4e6000.ethernet: FMan MAC address: 00:e0:0c:00:3b:03
fsl_mac ffe4e8000.ethernet: FMan dTSEC version: 0x08240101
fsl_mac ffe4e8000.ethernet: FMan MAC address: 00:e0:0c:00:3b:04
cpu1/1: Applying 10G TX ECC workaround (10GMAC-A004) ...
cpu1/1: done.
fsl_mac ffe4f0000.ethernet: FMan XGEC version: 0x00010330
fsl_mac ffe4f0000.ethernet: FMan MAC address: 00:e0:0c:00:3b:05
fsl_dpa: FSL DPAA Ethernet driver ()
fsl_dpa: fsl_dpa: Probed interface eth0
fsl_dpa: fsl_dpa: Probed interface eth1
fsl_dpa: fsl_dpa: Probed interface eth2
fsl_dpa: fsl_dpa: Probed interface eth3
fsl_dpa: fsl_dpa: Probed interface eth4
fsl_dpa_shared: FSL DPAA Shared Ethernet driver ()
fsl_dpa_proxy: FSL DPAA Proxy initialization driver ()
fsl_oh: FSL FMan Offline Parsing port driver ()
e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
e1000: Copyright (c) 1999-2006 Intel Corporation.
e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
e1000e 0000:01:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
e1000e 0000:01:00.0 eth5: registered PHC clock
ata1: No Device OR PHYRDY change,Hstatus = 0xa0000000
ata1: SATA link down (SStatus 0 SControl 300)
e1000e 0000:01:00.0 eth5: (PCI Express:2.5GT/s:Width x1) 00:1b:21:82:a0:c8
ata2: Signature Update detected @ 504 msecs
e1000e 0000:01:00.0 eth5: Intel(R) PRO/1000 Network Connection
e1000e 0000:01:00.0 eth5: MAC: 3, PHY: 8, PBA No: E46981-004
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-pci: OHCI PCI platform driver
fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
fsl-ehci fsl-ehci.0: irq 44, io mem 0xffe210000
fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
usbcore: registered new interface driver usb-storage
i2c /dev entries driver
mpc-i2c ffe118100.i2c: timeout 1000000 us
mpc-i2c ffe119100.i2c: timeout 1000000 us
rtc-ds3232 1-0068: rtc core: registered ds3232 as rtc0
mpc-i2c ffe118000.i2c: timeout 1000000 us
mpc-i2c ffe119000.i2c: timeout 1000000 us
ina2xx 1-0040: power monitor ina220 (Rshunt = 1000 uOhm)
ina2xx 1-0041: power monitor ina220 (Rshunt = 1000 uOhm)
ina2xx 1-0044: power monitor ina220 (Rshunt = 1000 uOhm)
ina2xx 1-0045: power monitor ina220 (Rshunt = 1000 uOhm)
Freescale(R) MPC85xx EDAC driver, (C) 2006 Montavista Software
EDAC MC0: Giving out device to 'MPC85xx_edac' 'mpc85xx_mc_err': DEV mpc85xx_mc_err
MPC85xx_edac acquired irq 490 for MC
MPC85xx_edac MC err registered
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
/soc@ffe000000/sdhc@114000: voltage-ranges unspecified
ata2.00: ATA-7: Hitachi HDS721616PLA380, P22OA70A, max UDMA/133
ata2.00: 321672960 sectors, multi 0: LBA48 NCQ (depth 16/32)
ata2.00: configured for UDMA/133
scsi 1:0:0:0: Direct-Access ATA Hitachi HDS72161 P22O PQ: 0 ANSI: 5
sd 1:0:0:0: [sda] 321672960 512-byte logical blocks: (164 GB/153 GiB)
sd 1:0:0:0: Attached scsi generic sg0 type 0
mmc0: SDHCI controller on ffe114000.sdhc [ffe114000.sdhc] using ADMA
platform caam_qi.0: Linux CAAM Queue I/F driver initialised
caam ffe300000.crypto: device ID = 0x0a12010000000000 (Era 3)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
caam ffe300000.crypto: job rings = 4, qi = 1
sda: sda1
sd 1:0:0:0: [sda] Attached SCSI disk
caam algorithms registered in /proc/crypto
caam_jr ffe301000.jr: registering rng-caam
caam ffe300000.crypto: fsl,sec-v4.2 algorithms registered in /proc/crypto
platform caam_qi.0: fsl,sec-v4.2 algorithms registered in /proc/crypto
Freescale USDPAA process driver
fsl-usdpaa: no region found
Freescale USDPAA process IRQ driver
fsl-pme ffe316000.pme: ver: 0x00100201
Freescale pme2 db driver
Freescale pme2 scan driver
fsl-pme2-scan: device pme_scan registered
Freescale hypervisor management driver
fsl-hv: no hypervisor found
ipip: IPv4 over IPv4 tunneling driver
TCP: cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
8021q: 802.1Q VLAN Support v1.8
Key type dns_resolver registered
libphy: mdio_mux: probed
libphy: mdio_mux: probed
mdio_bus 0.48: cannot get PHY at address 28
mdio_bus 0.48: cannot get PHY at address 29
mdio_bus 0.48: cannot get PHY at address 30
mdio_bus 0.48: cannot get PHY at address 31
mdio-mux-mmioreg fffdf0009.mdio-mux-emi1: Version 1.0
fsl_dpa_macless: FSL DPAA MACless Ethernet driver ()
fsl_dpa_generic: FSL DPAA Generic Ethernet driver ()
rtc-ds3232 1-0068: setting system clock to 2015-05-25 15:26:15 UTC (1432567575)
mmc0: new SDHC card at address baac
usb 1-1: new high-speed USB device number 2 using fsl-ehci
mmcblk0: mmc0:baac SD04G 3.69 GiB
mmcblk0: p1
usb-storage 1-1:1.0: USB Mass Storage device detected
scsi4 : usb-storage 1-1:1.0
scsi 4:0:0:0: Direct-Access Kingston DataTraveler 160 PMAP PQ: 0 ANSI: 0 CCS
sd 4:0:0:0: Attached scsi generic sg1 type 0
ata3: SATA link down (SStatus 0 SControl 0)
sd 4:0:0:0: [sdb] 7831552 512-byte logical blocks: (4.00 GB/3.73 GiB)
sd 4:0:0:0: [sdb] Write Protect is off
sd 4:0:0:0: [sdb] No Caching mode page found
sd 4:0:0:0: [sdb] Assuming drive cache: write through
sd 4:0:0:0: [sdb] No Caching mode page found
sd 4:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
sd 4:0:0:0: [sdb] No Caching mode page found
sd 4:0:0:0: [sdb] Assuming drive cache: write through
sd 4:0:0:0: [sdb] Attached SCSI removable disk
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata4.00: ATA-6: ST380013AS, 3.42, max UDMA/133
ata4.00: 156301488 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata4.00: configured for UDMA/100
scsi 3:0:0:0: Direct-Access ATA ST380013AS 3.42 PQ: 0 ANSI: 5
sd 3:0:0:0: [sdc] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
sd 3:0:0:0: Attached scsi generic sg2 type 0
sd 3:0:0:0: [sdc] Write Protect is off
sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1
sd 3:0:0:0: [sdc] Attached SCSI disk
RAMDISK: gzip image found at block 0
VFS: Mounted root (ext2 filesystem) readonly on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 272K (c0852000 - c0896000)
INIT: version 2.88 booting
Starting udev
udevd[1109]: starting version 182
bootlogd: cannot allocate pseudo tty: No such file or directory
Populating dev cache
Running postinst /etc/rpm-postinsts/100-sysvinit-inittab...
INIT: Entering runlevel: 5un-postinsts exists du
Configuring network interfaces... done.
Starting syslogd/klogd: done
Poky (Yocto Project Reference Distro) 1.7.2 p3041ds /dev/ttyS0
p3041ds login: root
root@p3041ds:~# dmesg | grep ata
ata4: SATA max UDMA/100 host m128@0xc40000000 port 0xc40006000 irq 42
ata1: No Device OR PHYRDY change,Hstatus = 0xa0000000
ata1: SATA link down (SStatus 0 SControl 300)
ata2: Signature Update detected @ 504 msecs
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: ATA-7: Hitachi HDS721616PLA380, P22OA70A, max UDMA/133
ata2.00: 321672960 sectors, multi 0: LBA48 NCQ (depth 16/32)
ata2.00: configured for UDMA/133
scsi 4:0:0:0: Direct-Access Kingston DataTraveler 160 PMAP PQ: 0 ANSI: 0 CCS
ata3: SATA link down (SStatus 0 SControl 0)
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata4.00: ATA-6: ST380013AS, 3.42, max UDMA/133
ata4.00: 156301488 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata4.00: configured for UDMA/100
root@p3041ds:~# dmesh
-sh: dmesh: not found
root@p3041ds:~# dmesg
ata4: SATA max UDMA/100 host m128@0xc40000000 port 0xc40006000 irq 42
fe8000000.flash: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002801
Amd/Fujitsu Extended Query Table at 0x0040
Amd/Fujitsu Extended Query version 1.3.
number of CFI chips: 1
ONFI param page 0 valid
ONFI flash detected
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xdc (Micron MT29F4G08ABADAWP), 512MiB, page size: 2048, OOB size: 64
Bad block table found at page 262080, version 0x01
Bad block table found at page 262016, version 0x01
6 ofpart partitions found on MTD device fffa00000.flash
Creating 6 MTD partitions on "fffa00000.flash":
0x000000000000-0x000002000000 : "NAND U-Boot Image"
0x000002000000-0x000012000000 : "NAND Root File System"
0x000012000000-0x00001a000000 : "NAND Compressed RFS Image"
0x00001a000000-0x00001e000000 : "NAND Linux Kernel Image"
0x00001e000000-0x00001f000000 : "NAND DTB Image"
0x00001f000000-0x000040000000 : "NAND Writable User area"
mtd: partition "NAND Writable User area" extends beyond the end of device "fffa00000.flash" -- size truncated to 0x1000000
eLBC NAND device at 0xfffa00000, bank 2
fsl_espi ffe110000.spi: master is unqueued, this is deprecated
m25p80 spi32766.0: found s25fl129p1, expected s25sl12801
m25p80 spi32766.0: s25fl129p1 (16384 Kbytes)
4 ofpart partitions found on MTD device spi32766.0
Creating 4 MTD partitions on "spi32766.0":
0x000000000000-0x000000100000 : "u-boot"
0x000000100000-0x000000600000 : "kernel"
0x000000600000-0x000000700000 : "dtb"
0x000000700000-0x000001000000 : "file system"
fsl_espi ffe110000.spi: at 0xf116e000 (irq = 53)
libphy: Fixed MDIO Bus: probed
mdio-mux-mmioreg fffdf0009.mdio-mux-emi1: failed to register mdio-mux bus /localbus@ffe124000/board-control@3,0/mdio-mux-emi1
platform fffdf0009.mdio-mux-emi1: Driver mdio-mux-mmioreg requests probe deferral
libphy: Freescale PowerQUICC MII Bus: probed
libphy: Freescale XGMAC MDIO Bus: probed
mdio_bus ffe4f1000: MDIO read error
mdio_bus ffe4f1000: MDIO read error
mdio_bus ffe4f1000: MDIO read error
mdio_bus ffe4f1000: MDIO read error
mdio_bus ffe4f1000: cannot get PHY at address 4
Freescale FM module (May 25 2015:04:32:35), FMD API version 21.1.0
Freescale FM Ports module (May 25 2015:04:32:39)
dpaa_debugfs: FSL DPAA Ethernet debugfs entries ()
dpaa_generic_debugfs: FSL DPAA Ethernet debugfs entries ()
fsl_mac: fsl_mac: FSL FMan MAC API based driver ()
fsl_mac ffe4e0000.ethernet: FMan dTSEC version: 0x08240101
fsl_mac ffe4e0000.ethernet: FMan MAC address: 00:e0:0c:00:3b:00
fsl_mac ffe4e2000.ethernet: FMan dTSEC version: 0x08240101
fsl_mac ffe4e2000.ethernet: FMan MAC address: 00:e0:0c:00:3b:01
fsl_mac ffe4e4000.ethernet: FMan dTSEC version: 0x08240101
fsl_mac ffe4e4000.ethernet: FMan MAC address: 00:e0:0c:00:3b:02
fsl_mac ffe4e6000.ethernet: FMan dTSEC version: 0x08240101
fsl_mac ffe4e6000.ethernet: FMan MAC address: 00:e0:0c:00:3b:03
fsl_mac ffe4e8000.ethernet: FMan dTSEC version: 0x08240101
fsl_mac ffe4e8000.ethernet: FMan MAC address: 00:e0:0c:00:3b:04
cpu1/1: Applying 10G TX ECC workaround (10GMAC-A004) ...
cpu1/1: done.
fsl_mac ffe4f0000.ethernet: FMan XGEC version: 0x00010330
fsl_mac ffe4f0000.ethernet: FMan MAC address: 00:e0:0c:00:3b:05
fsl_dpa: FSL DPAA Ethernet driver ()
fsl_dpa: fsl_dpa: Probed interface eth0
fsl_dpa: fsl_dpa: Probed interface eth1
fsl_dpa: fsl_dpa: Probed interface eth2
fsl_dpa: fsl_dpa: Probed interface eth3
fsl_dpa: fsl_dpa: Probed interface eth4
fsl_dpa_shared: FSL DPAA Shared Ethernet driver ()
fsl_dpa_proxy: FSL DPAA Proxy initialization driver ()
fsl_oh: FSL FMan Offline Parsing port driver ()
e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
e1000: Copyright (c) 1999-2006 Intel Corporation.
e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
e1000e 0000:01:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
e1000e 0000:01:00.0 eth5: registered PHC clock
ata1: No Device OR PHYRDY change,Hstatus = 0xa0000000
ata1: SATA link down (SStatus 0 SControl 300)
e1000e 0000:01:00.0 eth5: (PCI Express:2.5GT/s:Width x1) 00:1b:21:82:a0:c8
ata2: Signature Update detected @ 504 msecs
e1000e 0000:01:00.0 eth5: Intel(R) PRO/1000 Network Connection
e1000e 0000:01:00.0 eth5: MAC: 3, PHY: 8, PBA No: E46981-004
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-pci: OHCI PCI platform driver
fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
fsl-ehci fsl-ehci.0: irq 44, io mem 0xffe210000
fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
usbcore: registered new interface driver usb-storage
i2c /dev entries driver
mpc-i2c ffe118100.i2c: timeout 1000000 us
mpc-i2c ffe119100.i2c: timeout 1000000 us
rtc-ds3232 1-0068: rtc core: registered ds3232 as rtc0
mpc-i2c ffe118000.i2c: timeout 1000000 us
mpc-i2c ffe119000.i2c: timeout 1000000 us
ina2xx 1-0040: power monitor ina220 (Rshunt = 1000 uOhm)
ina2xx 1-0041: power monitor ina220 (Rshunt = 1000 uOhm)
ina2xx 1-0044: power monitor ina220 (Rshunt = 1000 uOhm)
ina2xx 1-0045: power monitor ina220 (Rshunt = 1000 uOhm)
Freescale(R) MPC85xx EDAC driver, (C) 2006 Montavista Software
EDAC MC0: Giving out device to 'MPC85xx_edac' 'mpc85xx_mc_err': DEV mpc85xx_mc_err
MPC85xx_edac acquired irq 490 for MC
MPC85xx_edac MC err registered
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
/soc@ffe000000/sdhc@114000: voltage-ranges unspecified
ata2.00: ATA-7: Hitachi HDS721616PLA380, P22OA70A, max UDMA/133
ata2.00: 321672960 sectors, multi 0: LBA48 NCQ (depth 16/32)
ata2.00: configured for UDMA/133
scsi 1:0:0:0: Direct-Access ATA Hitachi HDS72161 P22O PQ: 0 ANSI: 5
sd 1:0:0:0: [sda] 321672960 512-byte logical blocks: (164 GB/153 GiB)
sd 1:0:0:0: Attached scsi generic sg0 type 0
mmc0: SDHCI controller on ffe114000.sdhc [ffe114000.sdhc] using ADMA
platform caam_qi.0: Linux CAAM Queue I/F driver initialised
caam ffe300000.crypto: device ID = 0x0a12010000000000 (Era 3)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
caam ffe300000.crypto: job rings = 4, qi = 1
sda: sda1
sd 1:0:0:0: [sda] Attached SCSI disk
caam algorithms registered in /proc/crypto
caam_jr ffe301000.jr: registering rng-caam
caam ffe300000.crypto: fsl,sec-v4.2 algorithms registered in /proc/crypto
platform caam_qi.0: fsl,sec-v4.2 algorithms registered in /proc/crypto
Freescale USDPAA process driver
fsl-usdpaa: no region found
Freescale USDPAA process IRQ driver
fsl-pme ffe316000.pme: ver: 0x00100201
Freescale pme2 db driver
Freescale pme2 scan driver
fsl-pme2-scan: device pme_scan registered
Freescale hypervisor management driver
fsl-hv: no hypervisor found
ipip: IPv4 over IPv4 tunneling driver
TCP: cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
8021q: 802.1Q VLAN Support v1.8
Key type dns_resolver registered
libphy: mdio_mux: probed
libphy: mdio_mux: probed
mdio_bus 0.48: cannot get PHY at address 28
mdio_bus 0.48: cannot get PHY at address 29
mdio_bus 0.48: cannot get PHY at address 30
mdio_bus 0.48: cannot get PHY at address 31
mdio-mux-mmioreg fffdf0009.mdio-mux-emi1: Version 1.0
fsl_dpa_macless: FSL DPAA MACless Ethernet driver ()
fsl_dpa_generic: FSL DPAA Generic Ethernet driver ()
rtc-ds3232 1-0068: setting system clock to 2015-05-25 15:26:15 UTC (1432567575)
mmc0: new SDHC card at address baac
usb 1-1: new high-speed USB device number 2 using fsl-ehci
mmcblk0: mmc0:baac SD04G 3.69 GiB
mmcblk0: p1
usb-storage 1-1:1.0: USB Mass Storage device detected
scsi4 : usb-storage 1-1:1.0
scsi 4:0:0:0: Direct-Access Kingston DataTraveler 160 PMAP PQ: 0 ANSI: 0 CCS
sd 4:0:0:0: Attached scsi generic sg1 type 0
ata3: SATA link down (SStatus 0 SControl 0)
sd 4:0:0:0: [sdb] 7831552 512-byte logical blocks: (4.00 GB/3.73 GiB)
sd 4:0:0:0: [sdb] Write Protect is off
sd 4:0:0:0: [sdb] Mode Sense: 03 41 00 00
sd 4:0:0:0: [sdb] No Caching mode page found
sd 4:0:0:0: [sdb] Assuming drive cache: write through
sd 4:0:0:0: [sdb] No Caching mode page found
sd 4:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
sd 4:0:0:0: [sdb] No Caching mode page found
sd 4:0:0:0: [sdb] Assuming drive cache: write through
sd 4:0:0:0: [sdb] Attached SCSI removable disk
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata4.00: ATA-6: ST380013AS, 3.42, max UDMA/133
ata4.00: 156301488 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata4.00: configured for UDMA/100
scsi 3:0:0:0: Direct-Access ATA ST380013AS 3.42 PQ: 0 ANSI: 5
sd 3:0:0:0: [sdc] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
sd 3:0:0:0: Attached scsi generic sg2 type 0
sd 3:0:0:0: [sdc] Write Protect is off
sd 3:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1
sd 3:0:0:0: [sdc] Attached SCSI disk
RAMDISK: gzip image found at block 0
VFS: Mounted root (ext2 filesystem) readonly on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 272K (c0852000 - c0896000)
udevd[1109]: starting version 182
root@p3041ds:~#
root@p3041ds:~#
root@p3041ds:~#
root@p3041ds:~#
root@p3041ds:~#
root@p3041ds:~# dmesg | grep ata
ata4: SATA max UDMA/100 host m128@0xc40000000 port 0xc40006000 irq 42
ata1: No Device OR PHYRDY change,Hstatus = 0xa0000000
ata1: SATA link down (SStatus 0 SControl 300)
ata2: Signature Update detected @ 504 msecs
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: ATA-7: Hitachi HDS721616PLA380, P22OA70A, max UDMA/133
ata2.00: 321672960 sectors, multi 0: LBA48 NCQ (depth 16/32)
ata2.00: configured for UDMA/133
scsi 4:0:0:0: Direct-Access Kingston DataTraveler 160 PMAP PQ: 0 ANSI: 0 CCS
ata3: SATA link down (SStatus 0 SControl 0)
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata4.00: ATA-6: ST380013AS, 3.42, max UDMA/133
ata4.00: 156301488 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata4.00: configured for UDMA/100
root@p3041ds:~# fdisk -l
Disk /dev/mtdblock0: 134 MB, 134217728 bytes
255 heads, 63 sectors/track, 16 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk /dev/mtdblock0 doesn't contain a valid partition table
Disk /dev/mtdblock1: 33 MB, 33554432 bytes
255 heads, 63 sectors/track, 4 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk /dev/mtdblock1 doesn't contain a valid partition table
Disk /dev/mtdblock2: 268 MB, 268435456 bytes
255 heads, 63 sectors/track, 32 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk /dev/mtdblock2 doesn't contain a valid partition table
Disk /dev/mtdblock3: 134 MB, 134217728 bytes
255 heads, 63 sectors/track, 16 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk /dev/mtdblock3 doesn't contain a valid partition table
Disk /dev/mtdblock4: 67 MB, 67108864 bytes
255 heads, 63 sectors/track, 8 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk /dev/mtdblock4 doesn't contain a valid partition table
Disk /dev/mtdblock5: 16 MB, 16777216 bytes
255 heads, 63 sectors/track, 2 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk /dev/mtdblock5 doesn't contain a valid partition table
Disk /dev/mtdblock6: 16 MB, 16777216 bytes
255 heads, 63 sectors/track, 2 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk /dev/mtdblock6 doesn't contain a valid partition table
Disk /dev/mtdblock7: 1 MB, 1048576 bytes
255 heads, 63 sectors/track, 0 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk /dev/mtdblock7 doesn't contain a valid partition table
Disk /dev/mtdblock8: 5 MB, 5242880 bytes
255 heads, 63 sectors/track, 0 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk /dev/mtdblock8 doesn't contain a valid partition table
Disk /dev/mtdblock9: 1 MB, 1048576 bytes
255 heads, 63 sectors/track, 0 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk /dev/mtdblock9 doesn't contain a valid partition table
Disk /dev/mtdblock10: 9 MB, 9437184 bytes
255 heads, 63 sectors/track, 1 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk /dev/mtdblock10 doesn't contain a valid partition table
Disk /dev/sda: 164.6 GB, 164696555520 bytes
1 heads, 63 sectors/track, 5105920 cylinders
Units = cylinders of 63 * 512 = 32256 bytes
Device Boot Start End Blocks Id System
/dev/sda1 33 5105920 160835456 83 Linux
Partition 1 does not end on cylinder boundary
Disk /dev/mmcblk0: 3965 MB, 3965190144 bytes
1 heads, 16 sectors/track, 484032 cylinders
Units = cylinders of 16 * 512 = 8192 bytes
Device Boot Start End Blocks Id System
/dev/mmcblk0p1 129 484032 3871232 83 Linux
Partition 1 does not end on cylinder boundary
Disk /dev/sdb: 4009 MB, 4009754624 bytes
1 heads, 62 sectors/track, 126315 cylinders
Units = cylinders of 62 * 512 = 31744 bytes
Device Boot Start End Blocks Id System
/dev/sdb1 34 126316 3914752 83 Linux
Partition 1 does not end on cylinder boundary
Disk /dev/sdc: 80.0 GB, 80026361856 bytes
1 heads, 48 sectors/track, 3256281 cylinders
Units = cylinders of 48 * 512 = 24576 bytes
Device Boot Start End Blocks Id System
/dev/sdc1 43 3256281 78149720 83 Linux
root@p3041ds:~#
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: P3041DS: SATA SCSI disk gives errors
2015-05-25 10:55 ` Luo Zhenhua
@ 2015-05-25 12:18 ` Siva Borra
2015-05-26 1:54 ` Luo Zhenhua
0 siblings, 1 reply; 4+ messages in thread
From: Siva Borra @ 2015-05-25 12:18 UTC (permalink / raw)
To: Luo Zhenhua, meta-freescale@yoctoproject.org; +Cc: Adrian Dudau
Hi Luo,
Thank you. Can you share the board revision?
The board revision I have tried is :
Board: P3041DS, Sys ID: 0x1c, Sys Ver: 0x12, FPGA Ver: 0x05, vBank: 0
U-Boot 2011.06-rc2 (Jun 09 2011 - 20:15:17)
And the HDD used is:
SATA device 1: Model: Hitachi HDS721050CLA362 Firm: JP2OA3MA Ser#:
JP1511HJ3TTD0K
Type: Hard Disk
Supports 48-bit addressing
Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
Regards,
Siva Borra.
On 2015-05-25 12:55, Luo Zhenhua wrote:
> Hello Siva,
>
> I tried the dizzy branch to build images and boot p3041ds board (uImage, dtb, core-image-mininal.rootfs.ext2.gz.u-boot), the SATA is launched normally.
>
> Layers commit:
> Poky - dizzy:9c4ff467f66428488b1cd9798066a8cb5d6b4c3b
> meta-openembedded - dizzy:5b6f39ce325d490fc382d5d59c5b8b9d5fa38b38
> meta-fsl-ppc - dizzy:5eeeb3ad74b72d904f805bc6e248e93e722b45c4
>
> The full boot log is attached.
>
>
> Best Regards,
>
> Zhenhua
>
>> -----Original Message-----
>> From: meta-freescale-bounces@yoctoproject.org [mailto:meta-freescale-
>> bounces@yoctoproject.org] On Behalf Of Siva Borra
>> Sent: Friday, May 22, 2015 4:26 PM
>> To: meta-freescale@yoctoproject.org
>> Cc: Adrian Dudau
>> Subject: [meta-freescale] P3041DS: SATA SCSI disk gives errors
>>
>> Hello,
>>
>> With latest dizzy branch of meta-fsl-ppc, with revision (linux-qoriq_3.12.bb and
>> linux-qoriq_3.12-prt.bb, Linux SRCREV =
>> "6619b8b55796cdf0cec04b66a71288edd3057229")
>> Instead of recognizing the HDD attached at SATA, it gives the following errors.
>>
>> [ 2.153541] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x1) [ 6.800430]
>> ata1.00: failed to IDENTIFY (I/O error, err_mask=0x1) [ 7.822380] ata2.00: failed
>> to IDENTIFY (I/O error, err_mask=0x1) [ 11.966438] ata1.00: failed to IDENTIFY
>> (I/O error, err_mask=0x1) [ 13.489386] ata2.00: failed to IDENTIFY (I/O error,
>> err_mask=0x1)
>>
>> Same feature works fine with 3.0.xx kernel supplied with board. Please suggest
>> how to fix this issue?
>>
>> Regards,
>> Siva Borra.
>>
>> --
>> _______________________________________________
>> meta-freescale mailing list
>> meta-freescale@yoctoproject.org
>> https://lists.yoctoproject.org/listinfo/meta-freescale
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: P3041DS: SATA SCSI disk gives errors
2015-05-25 12:18 ` Siva Borra
@ 2015-05-26 1:54 ` Luo Zhenhua
0 siblings, 0 replies; 4+ messages in thread
From: Luo Zhenhua @ 2015-05-26 1:54 UTC (permalink / raw)
To: Siva Borra, meta-freescale@yoctoproject.org; +Cc: Adrian Dudau
Hi Siva,
Board: P3041DS, Sys ID: 0x20, Sys Ver: 0x01, FPGA Ver: 0x02, vBank: 0
U-Boot 2014.07QorIQ-SDK-V1.7+g659b6a2 (Dec 13 2014 - 14:05:10)
SATA device 1: Model: Hitachi HDS721616PLA380 Firm: P22OA70A Ser#: PVB300Z20142YF
Type: Hard Disk
Capacity: 157066.8 MB = 153.3 GB (321672960 x 512)
Best Regards,
Zhenhua
> -----Original Message-----
> From: Siva Borra [mailto:siva.borra@enea.com]
> Sent: Monday, May 25, 2015 8:18 PM
> To: Luo Zhenhua-B19537; meta-freescale@yoctoproject.org
> Cc: Adrian Dudau
> Subject: Re: [meta-freescale] P3041DS: SATA SCSI disk gives errors
>
> Hi Luo,
>
> Thank you. Can you share the board revision?
>
> The board revision I have tried is :
> Board: P3041DS, Sys ID: 0x1c, Sys Ver: 0x12, FPGA Ver: 0x05, vBank: 0 U-Boot
> 2011.06-rc2 (Jun 09 2011 - 20:15:17) And the HDD used is:
>
> SATA device 1: Model: Hitachi HDS721050CLA362 Firm: JP2OA3MA Ser#:
> JP1511HJ3TTD0K
> Type: Hard Disk
> Supports 48-bit addressing
> Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
>
> Regards,
> Siva Borra.
>
> On 2015-05-25 12:55, Luo Zhenhua wrote:
> > Hello Siva,
> >
> > I tried the dizzy branch to build images and boot p3041ds board (uImage, dtb,
> core-image-mininal.rootfs.ext2.gz.u-boot), the SATA is launched normally.
> >
> > Layers commit:
> > Poky - dizzy:9c4ff467f66428488b1cd9798066a8cb5d6b4c3b
> > meta-openembedded - dizzy:5b6f39ce325d490fc382d5d59c5b8b9d5fa38b38
> > meta-fsl-ppc - dizzy:5eeeb3ad74b72d904f805bc6e248e93e722b45c4
> >
> > The full boot log is attached.
> >
> >
> > Best Regards,
> >
> > Zhenhua
> >
> >> -----Original Message-----
> >> From: meta-freescale-bounces@yoctoproject.org [mailto:meta-freescale-
> >> bounces@yoctoproject.org] On Behalf Of Siva Borra
> >> Sent: Friday, May 22, 2015 4:26 PM
> >> To: meta-freescale@yoctoproject.org
> >> Cc: Adrian Dudau
> >> Subject: [meta-freescale] P3041DS: SATA SCSI disk gives errors
> >>
> >> Hello,
> >>
> >> With latest dizzy branch of meta-fsl-ppc, with revision
> >> (linux-qoriq_3.12.bb and linux-qoriq_3.12-prt.bb, Linux SRCREV =
> >> "6619b8b55796cdf0cec04b66a71288edd3057229")
> >> Instead of recognizing the HDD attached at SATA, it gives the following
> errors.
> >>
> >> [ 2.153541] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x1) [
> >> 6.800430]
> >> ata1.00: failed to IDENTIFY (I/O error, err_mask=0x1) [ 7.822380]
> >> ata2.00: failed to IDENTIFY (I/O error, err_mask=0x1) [ 11.966438]
> >> ata1.00: failed to IDENTIFY (I/O error, err_mask=0x1) [ 13.489386]
> >> ata2.00: failed to IDENTIFY (I/O error,
> >> err_mask=0x1)
> >>
> >> Same feature works fine with 3.0.xx kernel supplied with board.
> >> Please suggest how to fix this issue?
> >>
> >> Regards,
> >> Siva Borra.
> >>
> >> --
> >> _______________________________________________
> >> meta-freescale mailing list
> >> meta-freescale@yoctoproject.org
> >> https://lists.yoctoproject.org/listinfo/meta-freescale
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2015-05-26 1:54 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2015-05-22 8:25 P3041DS: SATA SCSI disk gives errors Siva Borra
2015-05-25 10:55 ` Luo Zhenhua
2015-05-25 12:18 ` Siva Borra
2015-05-26 1:54 ` Luo Zhenhua
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.