HT80 monitoring using ath10k

HT80 monitoring using ath10k

[Yeoh Chun-Yeow]

Hi, all

Anyone has able to capture the packet sent using HT80 or even higher
putting ath10k in monitor mode?

Please let me know. Thanks

Regards,
Chun-Yeow

_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k

Re: HT80 monitoring using ath10k

[Ben Greear]

On 09/01/2015 06:20 PM, Yeoh Chun-Yeow wrote:
> Hi, all
>
> Anyone has able to capture the packet sent using HT80 or even higher
> putting ath10k in monitor mode?
>
> Please let me know. Thanks

I guess it would require wave-2 hardware to even have a chance of HT160?

I thought HT80 capture worked fine on peregrine....I should have a chance to
try this for some upcoming IBSS work I have scheduled for my 10.1 firmware.

Thanks,
Ben

-- 
Ben Greear <greearb@candelatech.com>
Candela Technologies Inc  http://www.candelatech.com


_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k

Re: HT80 monitoring using ath10k

[Yeoh Chun-Yeow]

On Thu, Sep 3, 2015 at 2:46 AM, Ben Greear <greearb@candelatech.com> wrote:
> On 09/01/2015 06:20 PM, Yeoh Chun-Yeow wrote:
>>
>> Hi, all
>>
>> Anyone has able to capture the packet sent using HT80 or even higher
>> putting ath10k in monitor mode?
>>
>> Please let me know. Thanks
>
>
> I guess it would require wave-2 hardware to even have a chance of HT160?
>
> I thought HT80 capture worked fine on peregrine....I should have a chance to
> try this for some upcoming IBSS work I have scheduled for my 10.1 firmware.

Did you ever try it before with HT80?

I set using the following after bring up the interface:
iw moni0 set freq 5180 80 5210

But not seeing any data packet and just those mgmt frame.

---
Chun-Yeow

_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k

Re: HT80 monitoring using ath10k

[Ben Greear]

On 09/02/2015 08:32 PM, Yeoh Chun-Yeow wrote:
> On Thu, Sep 3, 2015 at 2:46 AM, Ben Greear <greearb@candelatech.com> wrote:
>> On 09/01/2015 06:20 PM, Yeoh Chun-Yeow wrote:
>>>
>>> Hi, all
>>>
>>> Anyone has able to capture the packet sent using HT80 or even higher
>>> putting ath10k in monitor mode?
>>>
>>> Please let me know. Thanks
>>
>>
>> I guess it would require wave-2 hardware to even have a chance of HT160?
>>
>> I thought HT80 capture worked fine on peregrine....I should have a chance to
>> try this for some upcoming IBSS work I have scheduled for my 10.1 firmware.
>
> Did you ever try it before with HT80?
>
> I set using the following after bring up the interface:
> iw moni0 set freq 5180 80 5210
>
> But not seeing any data packet and just those mgmt frame.

To be honest, I normally configure an AP on appropriate channels, and
then just start up a monitor interface.  Then, stop the AP interface.
I have poor luck getting a monitor interface to reliably configure the
proper channel & width on its own.

Thanks,
Ben


-- 
Ben Greear <greearb@candelatech.com>
Candela Technologies Inc  http://www.candelatech.com

_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k