* [PATCH V3] AHCI: Workaround for ThunderX Errata#22536
@ 2016-02-16 20:08 ` tchalamarla at caviumnetworks.com
0 siblings, 0 replies; 18+ messages in thread
From: tchalamarla @ 2016-02-16 20:08 UTC (permalink / raw)
To: tj; +Cc: stripathi, linux-ide, linux-kernel, linux-arm-kernel, tchalamarla
From: Tirumalesh Chalamarla <tchalamarla@caviumnetworks.com>
Due to Errata in ThunderX, HOST_IRQ_STAT should be
cleared before leaving the interrupt handler.
The patch attempts to satisfy the need.
Changes from V2:
- removed newfile
- code is now under CONFIG_ARM64
Changes from V1:
- Rebased on top of libata/for-4.6
- Moved ThunderX intr handler to new file
Signed-off-by: Tirumalesh Chalamarla <tchalamarla@caviumnetworks.com>
---
drivers/ata/ahci.c | 44 ++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 44 insertions(+)
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index 546a369..c8496fc 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -1325,6 +1325,44 @@ static inline void ahci_gtf_filter_workaround(struct ata_host *host)
{}
#endif
+#ifdef CONFIG_ARM64
+/* Due to ERRATA#22536, ThunderX need to handle
+ * HOST_IRQ_STAT differently.
+ * Work around is to make sure all pending IRQs
+ * are served before leaving handler
+ */
+static irqreturn_t ahci_thunderx_irq_handler(int irq, void *dev_instance)
+{
+ struct ata_host *host = dev_instance;
+ struct ahci_host_priv *hpriv;
+ unsigned int rc = 0;
+ void __iomem *mmio;
+ u32 irq_stat, irq_masked;
+ unsigned int handled = 1;
+
+ VPRINTK("ENTER\n");
+ hpriv = host->private_data;
+ mmio = hpriv->mmio;
+ irq_stat = readl(mmio + HOST_IRQ_STAT);
+ if (!irq_stat)
+ return IRQ_NONE;
+
+ do {
+ irq_masked = irq_stat & hpriv->port_map;
+ spin_lock(&host->lock);
+ rc = ahci_handle_port_intr(host, irq_masked);
+ if (!rc)
+ handled = 0;
+ writel(irq_stat, mmio + HOST_IRQ_STAT);
+ irq_stat = readl(mmio + HOST_IRQ_STAT);
+ spin_unlock(&host->lock);
+ } while (irq_stat);
+ VPRINTK("EXIT\n");
+
+ return IRQ_RETVAL(handled);
+}
+#endif
+
/*
* ahci_init_msix() - optionally enable per-port MSI-X otherwise defer
* to single msi.
@@ -1560,6 +1598,12 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
if (ahci_broken_devslp(pdev))
hpriv->flags |= AHCI_HFLAG_NO_DEVSLP;
+#ifdef CONFIG_ARM64
+ /* this should be done before save config*/
+ if (pdev->vendor == 0x177d && pdev->device == 0xa01c)
+ hpriv->irq_handler = ahci_thunderx_irq_handler;
+#endif
+
/* save initial config */
ahci_pci_save_initial_config(pdev, hpriv);
--
2.1.0
^ permalink raw reply related [flat|nested] 18+ messages in thread* [PATCH V3] AHCI: Workaround for ThunderX Errata#22536
@ 2016-02-16 20:08 ` tchalamarla at caviumnetworks.com
0 siblings, 0 replies; 18+ messages in thread
From: tchalamarla at caviumnetworks.com @ 2016-02-16 20:08 UTC (permalink / raw)
To: linux-arm-kernel
From: Tirumalesh Chalamarla <tchalamarla@caviumnetworks.com>
Due to Errata in ThunderX, HOST_IRQ_STAT should be
cleared before leaving the interrupt handler.
The patch attempts to satisfy the need.
Changes from V2:
- removed newfile
- code is now under CONFIG_ARM64
Changes from V1:
- Rebased on top of libata/for-4.6
- Moved ThunderX intr handler to new file
Signed-off-by: Tirumalesh Chalamarla <tchalamarla@caviumnetworks.com>
---
drivers/ata/ahci.c | 44 ++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 44 insertions(+)
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index 546a369..c8496fc 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -1325,6 +1325,44 @@ static inline void ahci_gtf_filter_workaround(struct ata_host *host)
{}
#endif
+#ifdef CONFIG_ARM64
+/* Due to ERRATA#22536, ThunderX need to handle
+ * HOST_IRQ_STAT differently.
+ * Work around is to make sure all pending IRQs
+ * are served before leaving handler
+ */
+static irqreturn_t ahci_thunderx_irq_handler(int irq, void *dev_instance)
+{
+ struct ata_host *host = dev_instance;
+ struct ahci_host_priv *hpriv;
+ unsigned int rc = 0;
+ void __iomem *mmio;
+ u32 irq_stat, irq_masked;
+ unsigned int handled = 1;
+
+ VPRINTK("ENTER\n");
+ hpriv = host->private_data;
+ mmio = hpriv->mmio;
+ irq_stat = readl(mmio + HOST_IRQ_STAT);
+ if (!irq_stat)
+ return IRQ_NONE;
+
+ do {
+ irq_masked = irq_stat & hpriv->port_map;
+ spin_lock(&host->lock);
+ rc = ahci_handle_port_intr(host, irq_masked);
+ if (!rc)
+ handled = 0;
+ writel(irq_stat, mmio + HOST_IRQ_STAT);
+ irq_stat = readl(mmio + HOST_IRQ_STAT);
+ spin_unlock(&host->lock);
+ } while (irq_stat);
+ VPRINTK("EXIT\n");
+
+ return IRQ_RETVAL(handled);
+}
+#endif
+
/*
* ahci_init_msix() - optionally enable per-port MSI-X otherwise defer
* to single msi.
@@ -1560,6 +1598,12 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
if (ahci_broken_devslp(pdev))
hpriv->flags |= AHCI_HFLAG_NO_DEVSLP;
+#ifdef CONFIG_ARM64
+ /* this should be done before save config*/
+ if (pdev->vendor == 0x177d && pdev->device == 0xa01c)
+ hpriv->irq_handler = ahci_thunderx_irq_handler;
+#endif
+
/* save initial config */
ahci_pci_save_initial_config(pdev, hpriv);
--
2.1.0
^ permalink raw reply related [flat|nested] 18+ messages in thread* Re: [PATCH V3] AHCI: Workaround for ThunderX Errata#22536
2016-02-16 20:08 ` tchalamarla at caviumnetworks.com
@ 2016-02-17 16:12 ` Thomas Gleixner
-1 siblings, 0 replies; 18+ messages in thread
From: Thomas Gleixner @ 2016-02-17 16:12 UTC (permalink / raw)
To: tchalamarla; +Cc: tj, stripathi, linux-ide, linux-kernel, linux-arm-kernel
On Tue, 16 Feb 2016, tchalamarla@caviumnetworks.com wrote:
> +#ifdef CONFIG_ARM64
> +/* Due to ERRATA#22536, ThunderX need to handle
> + * HOST_IRQ_STAT differently.
> + * Work around is to make sure all pending IRQs
> + * are served before leaving handler
> + */
> +static irqreturn_t ahci_thunderx_irq_handler(int irq, void *dev_instance)
> +{
> + struct ata_host *host = dev_instance;
> + struct ahci_host_priv *hpriv;
> + unsigned int rc = 0;
> + void __iomem *mmio;
> + u32 irq_stat, irq_masked;
> + unsigned int handled = 1;
> +
> + VPRINTK("ENTER\n");
Come on. This VPRINK stuff is really pointless. Enable irq tracepoints, they
already track the enter/exit of interrupt handlers ....
Thanks,
tglx
^ permalink raw reply [flat|nested] 18+ messages in thread* [PATCH V3] AHCI: Workaround for ThunderX Errata#22536
@ 2016-02-17 16:12 ` Thomas Gleixner
0 siblings, 0 replies; 18+ messages in thread
From: Thomas Gleixner @ 2016-02-17 16:12 UTC (permalink / raw)
To: linux-arm-kernel
On Tue, 16 Feb 2016, tchalamarla at caviumnetworks.com wrote:
> +#ifdef CONFIG_ARM64
> +/* Due to ERRATA#22536, ThunderX need to handle
> + * HOST_IRQ_STAT differently.
> + * Work around is to make sure all pending IRQs
> + * are served before leaving handler
> + */
> +static irqreturn_t ahci_thunderx_irq_handler(int irq, void *dev_instance)
> +{
> + struct ata_host *host = dev_instance;
> + struct ahci_host_priv *hpriv;
> + unsigned int rc = 0;
> + void __iomem *mmio;
> + u32 irq_stat, irq_masked;
> + unsigned int handled = 1;
> +
> + VPRINTK("ENTER\n");
Come on. This VPRINK stuff is really pointless. Enable irq tracepoints, they
already track the enter/exit of interrupt handlers ....
Thanks,
tglx
^ permalink raw reply [flat|nested] 18+ messages in thread* Re: [PATCH V3] AHCI: Workaround for ThunderX Errata#22536
2016-02-17 16:12 ` Thomas Gleixner
(?)
@ 2016-02-25 20:31 ` Tirumalesh Chalamarla
-1 siblings, 0 replies; 18+ messages in thread
From: Tirumalesh Chalamarla @ 2016-02-25 20:31 UTC (permalink / raw)
To: Thomas Gleixner; +Cc: tj, stripathi, linux-ide, linux-kernel, linux-arm-kernel
On 02/17/2016 08:12 AM, Thomas Gleixner wrote:
> On Tue, 16 Feb 2016, tchalamarla@caviumnetworks.com wrote:
>> +#ifdef CONFIG_ARM64
>> +/* Due to ERRATA#22536, ThunderX need to handle
>> + * HOST_IRQ_STAT differently.
>> + * Work around is to make sure all pending IRQs
>> + * are served before leaving handler
>> + */
>> +static irqreturn_t ahci_thunderx_irq_handler(int irq, void *dev_instance)
>> +{
>> + struct ata_host *host = dev_instance;
>> + struct ahci_host_priv *hpriv;
>> + unsigned int rc = 0;
>> + void __iomem *mmio;
>> + u32 irq_stat, irq_masked;
>> + unsigned int handled = 1;
>> +
>> + VPRINTK("ENTER\n");
>
> Come on. This VPRINK stuff is really pointless. Enable irq tracepoints, they
> already track the enter/exit of interrupt handlers ....
>
sure. waiting for some more comments if any.
> Thanks,
>
> tglx
>
>
^ permalink raw reply [flat|nested] 18+ messages in thread* Re: [PATCH V3] AHCI: Workaround for ThunderX Errata#22536
@ 2016-02-25 20:31 ` Tirumalesh Chalamarla
0 siblings, 0 replies; 18+ messages in thread
From: Tirumalesh Chalamarla @ 2016-02-25 20:31 UTC (permalink / raw)
To: Thomas Gleixner; +Cc: tj, stripathi, linux-ide, linux-kernel, linux-arm-kernel
On 02/17/2016 08:12 AM, Thomas Gleixner wrote:
> On Tue, 16 Feb 2016, tchalamarla@caviumnetworks.com wrote:
>> +#ifdef CONFIG_ARM64
>> +/* Due to ERRATA#22536, ThunderX need to handle
>> + * HOST_IRQ_STAT differently.
>> + * Work around is to make sure all pending IRQs
>> + * are served before leaving handler
>> + */
>> +static irqreturn_t ahci_thunderx_irq_handler(int irq, void *dev_instance)
>> +{
>> + struct ata_host *host = dev_instance;
>> + struct ahci_host_priv *hpriv;
>> + unsigned int rc = 0;
>> + void __iomem *mmio;
>> + u32 irq_stat, irq_masked;
>> + unsigned int handled = 1;
>> +
>> + VPRINTK("ENTER\n");
>
> Come on. This VPRINK stuff is really pointless. Enable irq tracepoints, they
> already track the enter/exit of interrupt handlers ....
>
sure. waiting for some more comments if any.
> Thanks,
>
> tglx
>
>
^ permalink raw reply [flat|nested] 18+ messages in thread* [PATCH V3] AHCI: Workaround for ThunderX Errata#22536
@ 2016-02-25 20:31 ` Tirumalesh Chalamarla
0 siblings, 0 replies; 18+ messages in thread
From: Tirumalesh Chalamarla @ 2016-02-25 20:31 UTC (permalink / raw)
To: linux-arm-kernel
On 02/17/2016 08:12 AM, Thomas Gleixner wrote:
> On Tue, 16 Feb 2016, tchalamarla at caviumnetworks.com wrote:
>> +#ifdef CONFIG_ARM64
>> +/* Due to ERRATA#22536, ThunderX need to handle
>> + * HOST_IRQ_STAT differently.
>> + * Work around is to make sure all pending IRQs
>> + * are served before leaving handler
>> + */
>> +static irqreturn_t ahci_thunderx_irq_handler(int irq, void *dev_instance)
>> +{
>> + struct ata_host *host = dev_instance;
>> + struct ahci_host_priv *hpriv;
>> + unsigned int rc = 0;
>> + void __iomem *mmio;
>> + u32 irq_stat, irq_masked;
>> + unsigned int handled = 1;
>> +
>> + VPRINTK("ENTER\n");
>
> Come on. This VPRINK stuff is really pointless. Enable irq tracepoints, they
> already track the enter/exit of interrupt handlers ....
>
sure. waiting for some more comments if any.
> Thanks,
>
> tglx
>
>
^ permalink raw reply [flat|nested] 18+ messages in thread* Re: [PATCH V3] AHCI: Workaround for ThunderX Errata#22536
2016-02-25 20:31 ` Tirumalesh Chalamarla
@ 2016-02-29 21:12 ` Tejun Heo
-1 siblings, 0 replies; 18+ messages in thread
From: Tejun Heo @ 2016-02-29 21:12 UTC (permalink / raw)
To: Tirumalesh Chalamarla
Cc: Thomas Gleixner, stripathi, linux-ide, linux-kernel,
linux-arm-kernel
Hello,
Sorry about the delay.
On Thu, Feb 25, 2016 at 12:31:53PM -0800, Tirumalesh Chalamarla wrote:
> On 02/17/2016 08:12 AM, Thomas Gleixner wrote:
> >On Tue, 16 Feb 2016, tchalamarla@caviumnetworks.com wrote:
> >>+#ifdef CONFIG_ARM64
> >>+/* Due to ERRATA#22536, ThunderX need to handle
> >>+ * HOST_IRQ_STAT differently.
> >>+ * Work around is to make sure all pending IRQs
> >>+ * are served before leaving handler
> >>+ */
> >>+static irqreturn_t ahci_thunderx_irq_handler(int irq, void *dev_instance)
> >>+{
> >>+ struct ata_host *host = dev_instance;
> >>+ struct ahci_host_priv *hpriv;
> >>+ unsigned int rc = 0;
> >>+ void __iomem *mmio;
> >>+ u32 irq_stat, irq_masked;
> >>+ unsigned int handled = 1;
> >>+
> >>+ VPRINTK("ENTER\n");
> >
> >Come on. This VPRINK stuff is really pointless. Enable irq tracepoints, they
> >already track the enter/exit of interrupt handlers ....
>
> sure. waiting for some more comments if any.
Yeah, VPRINTK way predates tracepoints and is kinda silly at this
point. That said, it's used relatively consistently across libata and
some people still use it for debugging. We can replace them with
proper tracepoints but that's a work for another patchset. For now,
let's leave it in for consistency with counterparts.
Thanks.
--
tejun
^ permalink raw reply [flat|nested] 18+ messages in thread* [PATCH V3] AHCI: Workaround for ThunderX Errata#22536
@ 2016-02-29 21:12 ` Tejun Heo
0 siblings, 0 replies; 18+ messages in thread
From: Tejun Heo @ 2016-02-29 21:12 UTC (permalink / raw)
To: linux-arm-kernel
Hello,
Sorry about the delay.
On Thu, Feb 25, 2016 at 12:31:53PM -0800, Tirumalesh Chalamarla wrote:
> On 02/17/2016 08:12 AM, Thomas Gleixner wrote:
> >On Tue, 16 Feb 2016, tchalamarla at caviumnetworks.com wrote:
> >>+#ifdef CONFIG_ARM64
> >>+/* Due to ERRATA#22536, ThunderX need to handle
> >>+ * HOST_IRQ_STAT differently.
> >>+ * Work around is to make sure all pending IRQs
> >>+ * are served before leaving handler
> >>+ */
> >>+static irqreturn_t ahci_thunderx_irq_handler(int irq, void *dev_instance)
> >>+{
> >>+ struct ata_host *host = dev_instance;
> >>+ struct ahci_host_priv *hpriv;
> >>+ unsigned int rc = 0;
> >>+ void __iomem *mmio;
> >>+ u32 irq_stat, irq_masked;
> >>+ unsigned int handled = 1;
> >>+
> >>+ VPRINTK("ENTER\n");
> >
> >Come on. This VPRINK stuff is really pointless. Enable irq tracepoints, they
> >already track the enter/exit of interrupt handlers ....
>
> sure. waiting for some more comments if any.
Yeah, VPRINTK way predates tracepoints and is kinda silly at this
point. That said, it's used relatively consistently across libata and
some people still use it for debugging. We can replace them with
proper tracepoints but that's a work for another patchset. For now,
let's leave it in for consistency with counterparts.
Thanks.
--
tejun
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH V3] AHCI: Workaround for ThunderX Errata#22536
2016-02-16 20:08 ` tchalamarla at caviumnetworks.com
(?)
@ 2016-02-24 0:00 ` Tirumalesh Chalamarla
-1 siblings, 0 replies; 18+ messages in thread
From: Tirumalesh Chalamarla @ 2016-02-24 0:00 UTC (permalink / raw)
To: tj; +Cc: stripathi, linux-ide, linux-kernel, linux-arm-kernel
Hi Tejun,
Any more comments on this?
Thanks,
Tirumalesh.
On 02/16/2016 12:08 PM, tchalamarla@caviumnetworks.com wrote:
> From: Tirumalesh Chalamarla <tchalamarla@caviumnetworks.com>
>
> Due to Errata in ThunderX, HOST_IRQ_STAT should be
> cleared before leaving the interrupt handler.
> The patch attempts to satisfy the need.
>
> Changes from V2:
> - removed newfile
> - code is now under CONFIG_ARM64
>
> Changes from V1:
> - Rebased on top of libata/for-4.6
> - Moved ThunderX intr handler to new file
>
> Signed-off-by: Tirumalesh Chalamarla <tchalamarla@caviumnetworks.com>
> ---
> drivers/ata/ahci.c | 44 ++++++++++++++++++++++++++++++++++++++++++++
> 1 file changed, 44 insertions(+)
>
> diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
> index 546a369..c8496fc 100644
> --- a/drivers/ata/ahci.c
> +++ b/drivers/ata/ahci.c
> @@ -1325,6 +1325,44 @@ static inline void ahci_gtf_filter_workaround(struct ata_host *host)
> {}
> #endif
>
> +#ifdef CONFIG_ARM64
> +/* Due to ERRATA#22536, ThunderX need to handle
> + * HOST_IRQ_STAT differently.
> + * Work around is to make sure all pending IRQs
> + * are served before leaving handler
> + */
> +static irqreturn_t ahci_thunderx_irq_handler(int irq, void *dev_instance)
> +{
> + struct ata_host *host = dev_instance;
> + struct ahci_host_priv *hpriv;
> + unsigned int rc = 0;
> + void __iomem *mmio;
> + u32 irq_stat, irq_masked;
> + unsigned int handled = 1;
> +
> + VPRINTK("ENTER\n");
> + hpriv = host->private_data;
> + mmio = hpriv->mmio;
> + irq_stat = readl(mmio + HOST_IRQ_STAT);
> + if (!irq_stat)
> + return IRQ_NONE;
> +
> + do {
> + irq_masked = irq_stat & hpriv->port_map;
> + spin_lock(&host->lock);
> + rc = ahci_handle_port_intr(host, irq_masked);
> + if (!rc)
> + handled = 0;
> + writel(irq_stat, mmio + HOST_IRQ_STAT);
> + irq_stat = readl(mmio + HOST_IRQ_STAT);
> + spin_unlock(&host->lock);
> + } while (irq_stat);
> + VPRINTK("EXIT\n");
> +
> + return IRQ_RETVAL(handled);
> +}
> +#endif
> +
> /*
> * ahci_init_msix() - optionally enable per-port MSI-X otherwise defer
> * to single msi.
> @@ -1560,6 +1598,12 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
> if (ahci_broken_devslp(pdev))
> hpriv->flags |= AHCI_HFLAG_NO_DEVSLP;
>
> +#ifdef CONFIG_ARM64
> + /* this should be done before save config*/
> + if (pdev->vendor == 0x177d && pdev->device == 0xa01c)
> + hpriv->irq_handler = ahci_thunderx_irq_handler;
> +#endif
> +
> /* save initial config */
> ahci_pci_save_initial_config(pdev, hpriv);
>
>
^ permalink raw reply [flat|nested] 18+ messages in thread* Re: [PATCH V3] AHCI: Workaround for ThunderX Errata#22536
@ 2016-02-24 0:00 ` Tirumalesh Chalamarla
0 siblings, 0 replies; 18+ messages in thread
From: Tirumalesh Chalamarla @ 2016-02-24 0:00 UTC (permalink / raw)
To: tj; +Cc: stripathi, linux-ide, linux-kernel, linux-arm-kernel
Hi Tejun,
Any more comments on this?
Thanks,
Tirumalesh.
On 02/16/2016 12:08 PM, tchalamarla@caviumnetworks.com wrote:
> From: Tirumalesh Chalamarla <tchalamarla@caviumnetworks.com>
>
> Due to Errata in ThunderX, HOST_IRQ_STAT should be
> cleared before leaving the interrupt handler.
> The patch attempts to satisfy the need.
>
> Changes from V2:
> - removed newfile
> - code is now under CONFIG_ARM64
>
> Changes from V1:
> - Rebased on top of libata/for-4.6
> - Moved ThunderX intr handler to new file
>
> Signed-off-by: Tirumalesh Chalamarla <tchalamarla@caviumnetworks.com>
> ---
> drivers/ata/ahci.c | 44 ++++++++++++++++++++++++++++++++++++++++++++
> 1 file changed, 44 insertions(+)
>
> diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
> index 546a369..c8496fc 100644
> --- a/drivers/ata/ahci.c
> +++ b/drivers/ata/ahci.c
> @@ -1325,6 +1325,44 @@ static inline void ahci_gtf_filter_workaround(struct ata_host *host)
> {}
> #endif
>
> +#ifdef CONFIG_ARM64
> +/* Due to ERRATA#22536, ThunderX need to handle
> + * HOST_IRQ_STAT differently.
> + * Work around is to make sure all pending IRQs
> + * are served before leaving handler
> + */
> +static irqreturn_t ahci_thunderx_irq_handler(int irq, void *dev_instance)
> +{
> + struct ata_host *host = dev_instance;
> + struct ahci_host_priv *hpriv;
> + unsigned int rc = 0;
> + void __iomem *mmio;
> + u32 irq_stat, irq_masked;
> + unsigned int handled = 1;
> +
> + VPRINTK("ENTER\n");
> + hpriv = host->private_data;
> + mmio = hpriv->mmio;
> + irq_stat = readl(mmio + HOST_IRQ_STAT);
> + if (!irq_stat)
> + return IRQ_NONE;
> +
> + do {
> + irq_masked = irq_stat & hpriv->port_map;
> + spin_lock(&host->lock);
> + rc = ahci_handle_port_intr(host, irq_masked);
> + if (!rc)
> + handled = 0;
> + writel(irq_stat, mmio + HOST_IRQ_STAT);
> + irq_stat = readl(mmio + HOST_IRQ_STAT);
> + spin_unlock(&host->lock);
> + } while (irq_stat);
> + VPRINTK("EXIT\n");
> +
> + return IRQ_RETVAL(handled);
> +}
> +#endif
> +
> /*
> * ahci_init_msix() - optionally enable per-port MSI-X otherwise defer
> * to single msi.
> @@ -1560,6 +1598,12 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
> if (ahci_broken_devslp(pdev))
> hpriv->flags |= AHCI_HFLAG_NO_DEVSLP;
>
> +#ifdef CONFIG_ARM64
> + /* this should be done before save config*/
> + if (pdev->vendor == 0x177d && pdev->device == 0xa01c)
> + hpriv->irq_handler = ahci_thunderx_irq_handler;
> +#endif
> +
> /* save initial config */
> ahci_pci_save_initial_config(pdev, hpriv);
>
>
^ permalink raw reply [flat|nested] 18+ messages in thread* [PATCH V3] AHCI: Workaround for ThunderX Errata#22536
@ 2016-02-24 0:00 ` Tirumalesh Chalamarla
0 siblings, 0 replies; 18+ messages in thread
From: Tirumalesh Chalamarla @ 2016-02-24 0:00 UTC (permalink / raw)
To: linux-arm-kernel
Hi Tejun,
Any more comments on this?
Thanks,
Tirumalesh.
On 02/16/2016 12:08 PM, tchalamarla at caviumnetworks.com wrote:
> From: Tirumalesh Chalamarla <tchalamarla@caviumnetworks.com>
>
> Due to Errata in ThunderX, HOST_IRQ_STAT should be
> cleared before leaving the interrupt handler.
> The patch attempts to satisfy the need.
>
> Changes from V2:
> - removed newfile
> - code is now under CONFIG_ARM64
>
> Changes from V1:
> - Rebased on top of libata/for-4.6
> - Moved ThunderX intr handler to new file
>
> Signed-off-by: Tirumalesh Chalamarla <tchalamarla@caviumnetworks.com>
> ---
> drivers/ata/ahci.c | 44 ++++++++++++++++++++++++++++++++++++++++++++
> 1 file changed, 44 insertions(+)
>
> diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
> index 546a369..c8496fc 100644
> --- a/drivers/ata/ahci.c
> +++ b/drivers/ata/ahci.c
> @@ -1325,6 +1325,44 @@ static inline void ahci_gtf_filter_workaround(struct ata_host *host)
> {}
> #endif
>
> +#ifdef CONFIG_ARM64
> +/* Due to ERRATA#22536, ThunderX need to handle
> + * HOST_IRQ_STAT differently.
> + * Work around is to make sure all pending IRQs
> + * are served before leaving handler
> + */
> +static irqreturn_t ahci_thunderx_irq_handler(int irq, void *dev_instance)
> +{
> + struct ata_host *host = dev_instance;
> + struct ahci_host_priv *hpriv;
> + unsigned int rc = 0;
> + void __iomem *mmio;
> + u32 irq_stat, irq_masked;
> + unsigned int handled = 1;
> +
> + VPRINTK("ENTER\n");
> + hpriv = host->private_data;
> + mmio = hpriv->mmio;
> + irq_stat = readl(mmio + HOST_IRQ_STAT);
> + if (!irq_stat)
> + return IRQ_NONE;
> +
> + do {
> + irq_masked = irq_stat & hpriv->port_map;
> + spin_lock(&host->lock);
> + rc = ahci_handle_port_intr(host, irq_masked);
> + if (!rc)
> + handled = 0;
> + writel(irq_stat, mmio + HOST_IRQ_STAT);
> + irq_stat = readl(mmio + HOST_IRQ_STAT);
> + spin_unlock(&host->lock);
> + } while (irq_stat);
> + VPRINTK("EXIT\n");
> +
> + return IRQ_RETVAL(handled);
> +}
> +#endif
> +
> /*
> * ahci_init_msix() - optionally enable per-port MSI-X otherwise defer
> * to single msi.
> @@ -1560,6 +1598,12 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
> if (ahci_broken_devslp(pdev))
> hpriv->flags |= AHCI_HFLAG_NO_DEVSLP;
>
> +#ifdef CONFIG_ARM64
> + /* this should be done before save config*/
> + if (pdev->vendor == 0x177d && pdev->device == 0xa01c)
> + hpriv->irq_handler = ahci_thunderx_irq_handler;
> +#endif
> +
> /* save initial config */
> ahci_pci_save_initial_config(pdev, hpriv);
>
>
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH V3] AHCI: Workaround for ThunderX Errata#22536
2016-02-16 20:08 ` tchalamarla at caviumnetworks.com
@ 2016-02-29 21:17 ` Tejun Heo
-1 siblings, 0 replies; 18+ messages in thread
From: Tejun Heo @ 2016-02-29 21:17 UTC (permalink / raw)
To: tchalamarla; +Cc: stripathi, linux-ide, linux-kernel, linux-arm-kernel
On Tue, Feb 16, 2016 at 12:08:49PM -0800, tchalamarla@caviumnetworks.com wrote:
> From: Tirumalesh Chalamarla <tchalamarla@caviumnetworks.com>
>
> Due to Errata in ThunderX, HOST_IRQ_STAT should be
> cleared before leaving the interrupt handler.
> The patch attempts to satisfy the need.
>
> Changes from V2:
> - removed newfile
> - code is now under CONFIG_ARM64
>
> Changes from V1:
> - Rebased on top of libata/for-4.6
> - Moved ThunderX intr handler to new file
>
> Signed-off-by: Tirumalesh Chalamarla <tchalamarla@caviumnetworks.com>
Applied to libata/for-4.5-fixes w/ minor adjustments to comments.
Thanks.
--
tejun
^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH V3] AHCI: Workaround for ThunderX Errata#22536
@ 2016-02-29 21:17 ` Tejun Heo
0 siblings, 0 replies; 18+ messages in thread
From: Tejun Heo @ 2016-02-29 21:17 UTC (permalink / raw)
To: linux-arm-kernel
On Tue, Feb 16, 2016 at 12:08:49PM -0800, tchalamarla at caviumnetworks.com wrote:
> From: Tirumalesh Chalamarla <tchalamarla@caviumnetworks.com>
>
> Due to Errata in ThunderX, HOST_IRQ_STAT should be
> cleared before leaving the interrupt handler.
> The patch attempts to satisfy the need.
>
> Changes from V2:
> - removed newfile
> - code is now under CONFIG_ARM64
>
> Changes from V1:
> - Rebased on top of libata/for-4.6
> - Moved ThunderX intr handler to new file
>
> Signed-off-by: Tirumalesh Chalamarla <tchalamarla@caviumnetworks.com>
Applied to libata/for-4.5-fixes w/ minor adjustments to comments.
Thanks.
--
tejun
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH V3] AHCI: Workaround for ThunderX Errata#22536
2016-02-29 21:17 ` Tejun Heo
(?)
@ 2016-02-29 22:00 ` Tirumalesh Chalamarla
-1 siblings, 0 replies; 18+ messages in thread
From: Tirumalesh Chalamarla @ 2016-02-29 22:00 UTC (permalink / raw)
To: Tejun Heo; +Cc: stripathi, linux-ide, linux-kernel, linux-arm-kernel
Thanks.
On 02/29/2016 01:17 PM, Tejun Heo wrote:
> On Tue, Feb 16, 2016 at 12:08:49PM -0800, tchalamarla@caviumnetworks.com wrote:
>> From: Tirumalesh Chalamarla <tchalamarla@caviumnetworks.com>
>>
>> Due to Errata in ThunderX, HOST_IRQ_STAT should be
>> cleared before leaving the interrupt handler.
>> The patch attempts to satisfy the need.
>>
>> Changes from V2:
>> - removed newfile
>> - code is now under CONFIG_ARM64
>>
>> Changes from V1:
>> - Rebased on top of libata/for-4.6
>> - Moved ThunderX intr handler to new file
>>
>> Signed-off-by: Tirumalesh Chalamarla <tchalamarla@caviumnetworks.com>
>
> Applied to libata/for-4.5-fixes w/ minor adjustments to comments.
>
> Thanks.
>
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH V3] AHCI: Workaround for ThunderX Errata#22536
@ 2016-02-29 22:00 ` Tirumalesh Chalamarla
0 siblings, 0 replies; 18+ messages in thread
From: Tirumalesh Chalamarla @ 2016-02-29 22:00 UTC (permalink / raw)
To: Tejun Heo; +Cc: stripathi, linux-ide, linux-kernel, linux-arm-kernel
Thanks.
On 02/29/2016 01:17 PM, Tejun Heo wrote:
> On Tue, Feb 16, 2016 at 12:08:49PM -0800, tchalamarla@caviumnetworks.com wrote:
>> From: Tirumalesh Chalamarla <tchalamarla@caviumnetworks.com>
>>
>> Due to Errata in ThunderX, HOST_IRQ_STAT should be
>> cleared before leaving the interrupt handler.
>> The patch attempts to satisfy the need.
>>
>> Changes from V2:
>> - removed newfile
>> - code is now under CONFIG_ARM64
>>
>> Changes from V1:
>> - Rebased on top of libata/for-4.6
>> - Moved ThunderX intr handler to new file
>>
>> Signed-off-by: Tirumalesh Chalamarla <tchalamarla@caviumnetworks.com>
>
> Applied to libata/for-4.5-fixes w/ minor adjustments to comments.
>
> Thanks.
>
^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH V3] AHCI: Workaround for ThunderX Errata#22536
@ 2016-02-29 22:00 ` Tirumalesh Chalamarla
0 siblings, 0 replies; 18+ messages in thread
From: Tirumalesh Chalamarla @ 2016-02-29 22:00 UTC (permalink / raw)
To: linux-arm-kernel
Thanks.
On 02/29/2016 01:17 PM, Tejun Heo wrote:
> On Tue, Feb 16, 2016 at 12:08:49PM -0800, tchalamarla at caviumnetworks.com wrote:
>> From: Tirumalesh Chalamarla <tchalamarla@caviumnetworks.com>
>>
>> Due to Errata in ThunderX, HOST_IRQ_STAT should be
>> cleared before leaving the interrupt handler.
>> The patch attempts to satisfy the need.
>>
>> Changes from V2:
>> - removed newfile
>> - code is now under CONFIG_ARM64
>>
>> Changes from V1:
>> - Rebased on top of libata/for-4.6
>> - Moved ThunderX intr handler to new file
>>
>> Signed-off-by: Tirumalesh Chalamarla <tchalamarla@caviumnetworks.com>
>
> Applied to libata/for-4.5-fixes w/ minor adjustments to comments.
>
> Thanks.
>
^ permalink raw reply [flat|nested] 18+ messages in thread