* [PATCH 0/3] ARM: dts: imx6: add support for more i.MX6 modules from Ka-Ro electronics @ 2016-01-12 18:01 ` Lothar Waßmann 0 siblings, 0 replies; 19+ messages in thread From: Lothar Waßmann @ 2016-01-12 18:01 UTC (permalink / raw) To: linux-arm-kernel This patchset adds support for some more modules from Ka-Ro electronics GmbH based on i.MX6SOLO and i.MX6UL. The last patch adds another LVDS display for the existing TX6 LVDS modules. ^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH 0/3] ARM: dts: imx6: add support for more i.MX6 modules from Ka-Ro electronics @ 2016-01-12 18:01 ` Lothar Waßmann 0 siblings, 0 replies; 19+ messages in thread From: Lothar Waßmann @ 2016-01-12 18:01 UTC (permalink / raw) To: Ian Campbell, Kumar Gala, Mark Rutland, Pawel Moll, Rob Herring, Russell King, Sascha Hauer, Shawn Guo, devicetree, linux-arm-kernel, linux-kernel This patchset adds support for some more modules from Ka-Ro electronics GmbH based on i.MX6SOLO and i.MX6UL. The last patch adds another LVDS display for the existing TX6 LVDS modules. ^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH 1/3] ARM: dts: imx6: add support for Ka-Ro electronics TX6S-8034 module 2016-01-12 18:01 ` Lothar Waßmann @ 2016-01-12 18:01 ` Lothar Waßmann -1 siblings, 0 replies; 19+ messages in thread From: Lothar Waßmann @ 2016-01-12 18:01 UTC (permalink / raw) To: linux-arm-kernel Add support for the TX6S-8034 module from Ka-Ro electronics. The module is equipped with an i.MX6SOLO at 792MHz, 256MiB DDR3 SDRAM and 128MiB NAND flash. Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx6dl-tx6s-8034.dts | 255 +++++++++++++++++++++++++++++++++ 2 files changed, 256 insertions(+) create mode 100644 arch/arm/boot/dts/imx6dl-tx6s-8034.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index a4a6d70..ac406d8 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -312,6 +312,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6dl-sabrelite.dtb \ imx6dl-sabresd.dtb \ imx6dl-tx6dl-comtft.dtb \ + imx6dl-tx6s-8034.dtb \ imx6dl-tx6u-801x.dtb \ imx6dl-tx6u-811x.dtb \ imx6dl-udoo.dtb \ diff --git a/arch/arm/boot/dts/imx6dl-tx6s-8034.dts b/arch/arm/boot/dts/imx6dl-tx6s-8034.dts new file mode 100644 index 0000000..6545335 --- /dev/null +++ b/arch/arm/boot/dts/imx6dl-tx6s-8034.dts @@ -0,0 +1,255 @@ +/* + * Copyright 2015 Lothar Wa?mann <LW@KARO-electronics.de> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "imx6dl.dtsi" +#include "imx6qdl-tx6.dtsi" + +/ { + model = "Ka-Ro electronics TX6S-8034 Module"; + compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl"; + timestamp = __DATE__, __TIME__; + + aliases { + display = &display; + ipu1 = &ipu1; + }; + + cpus { + /delete-node/ cpu at 1; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>; + power-supply = <®_3v3>; + /* + * a poor man's way to create a 1:1 relationship between + * the PWM value and the actual duty cycle + */ + brightness-levels = < 0 1 2 3 4 5 6 7 8 9 + 10 11 12 13 14 15 16 17 18 19 + 20 21 22 23 24 25 26 27 28 29 + 30 31 32 33 34 35 36 37 38 39 + 40 41 42 43 44 45 46 47 48 49 + 50 51 52 53 54 55 56 57 58 59 + 60 61 62 63 64 65 66 67 68 69 + 70 71 72 73 74 75 76 77 78 79 + 80 81 82 83 84 85 86 87 88 89 + 90 91 92 93 94 95 96 97 98 99 + 100>; + default-brightness-level = <50>; + }; + + display: display at di0 { + compatible = "fsl,imx-parallel-display"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_disp0_1>; + interface-pix-fmt = "rgb24"; +// fsl,panel = <&lcd0_panel>; + status = "okay"; + + port { + display0_in: endpoint { + remote-endpoint = <&ipu1_di0_disp0>; + }; + }; + + display-timings { + VGA { + clock-frequency = <25200000>; + hactive = <640>; + vactive = <480>; + hback-porch = <48>; + hsync-len = <96>; + hfront-porch = <16>; + vback-porch = <31>; + vsync-len = <2>; + vfront-porch = <12>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + + ETV570 { + clock-frequency = <25200000>; + hactive = <640>; + vactive = <480>; + hback-porch = <114>; + hsync-len = <30>; + hfront-porch = <16>; + vback-porch = <32>; + vsync-len = <3>; + vfront-porch = <10>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + + ET0350 { + clock-frequency = <6413760>; + hactive = <320>; + vactive = <240>; + hback-porch = <34>; + hsync-len = <34>; + hfront-porch = <20>; + vback-porch = <15>; + vsync-len = <3>; + vfront-porch = <4>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + + ET0430 { + clock-frequency = <9009000>; + hactive = <480>; + vactive = <272>; + hback-porch = <2>; + hsync-len = <41>; + hfront-porch = <2>; + vback-porch = <2>; + vsync-len = <10>; + vfront-porch = <2>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + + ET0500 { + clock-frequency = <33264000>; + hactive = <800>; + vactive = <480>; + hback-porch = <88>; + hsync-len = <128>; + hfront-porch = <40>; + vback-porch = <33>; + vsync-len = <2>; + vfront-porch = <10>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + + ET0700 { /* same as ET0500 */ + clock-frequency = <33264000>; + hactive = <800>; + vactive = <480>; + hback-porch = <88>; + hsync-len = <128>; + hfront-porch = <40>; + vback-porch = <33>; + vsync-len = <2>; + vfront-porch = <10>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + + ETQ570 { + clock-frequency = <6596040>; + hactive = <320>; + vactive = <240>; + hback-porch = <38>; + hsync-len = <30>; + hfront-porch = <30>; + vback-porch = <16>; + vsync-len = <3>; + vfront-porch = <4>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + }; + }; + + lcd0_panel: lcd-panel { + compatible = "edt,et070080dh6", "simple-panel"; + power-supply = <®_lcd0_pwr>; + enable-gpios = <&gpio2 31 GPIO_ACTIVE_HIGH>; + backlight = <&backlight>; + status = "disabled"; + }; +}; + +&ds1339 { + status = "disabled"; +}; + +&pinctrl_hog { + fsl,pins = < + MX6QDL_PAD_EIM_A18__GPIO2_IO20 0x1b0b1 /* LED */ + MX6QDL_PAD_SD3_DAT2__GPIO7_IO06 0x1b0b1 /* ETN PHY RESET */ + MX6QDL_PAD_SD3_DAT4__GPIO7_IO01 0x1b0b1 /* ETN PHY INT */ + MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x1b0b1 /* PWR BTN */ + >; +}; + +&pinctrl_usdhc1 { + fsl,pins = < + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x070b1 + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x07099 + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x070b1 + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x070b1 + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x070b1 + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x070b1 + MX6QDL_PAD_SD3_CMD__GPIO7_IO02 0x170b0 /* SD1 CD */ + >; +}; + +&ipu1_di0_disp0 { + remote-endpoint = <&display0_in>; +}; + +®_lcd0_pwr { + status = "disabled"; +}; + +®_lcd1_pwr { + status = "disabled"; +}; -- 2.1.4 ^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH 1/3] ARM: dts: imx6: add support for Ka-Ro electronics TX6S-8034 module @ 2016-01-12 18:01 ` Lothar Waßmann 0 siblings, 0 replies; 19+ messages in thread From: Lothar Waßmann @ 2016-01-12 18:01 UTC (permalink / raw) To: Ian Campbell, Kumar Gala, Mark Rutland, Pawel Moll, Rob Herring, Russell King, Sascha Hauer, Shawn Guo, devicetree, linux-arm-kernel, linux-kernel Cc: Lothar Waßmann Add support for the TX6S-8034 module from Ka-Ro electronics. The module is equipped with an i.MX6SOLO at 792MHz, 256MiB DDR3 SDRAM and 128MiB NAND flash. Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx6dl-tx6s-8034.dts | 255 +++++++++++++++++++++++++++++++++ 2 files changed, 256 insertions(+) create mode 100644 arch/arm/boot/dts/imx6dl-tx6s-8034.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index a4a6d70..ac406d8 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -312,6 +312,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6dl-sabrelite.dtb \ imx6dl-sabresd.dtb \ imx6dl-tx6dl-comtft.dtb \ + imx6dl-tx6s-8034.dtb \ imx6dl-tx6u-801x.dtb \ imx6dl-tx6u-811x.dtb \ imx6dl-udoo.dtb \ diff --git a/arch/arm/boot/dts/imx6dl-tx6s-8034.dts b/arch/arm/boot/dts/imx6dl-tx6s-8034.dts new file mode 100644 index 0000000..6545335 --- /dev/null +++ b/arch/arm/boot/dts/imx6dl-tx6s-8034.dts @@ -0,0 +1,255 @@ +/* + * Copyright 2015 Lothar Waßmann <LW@KARO-electronics.de> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "imx6dl.dtsi" +#include "imx6qdl-tx6.dtsi" + +/ { + model = "Ka-Ro electronics TX6S-8034 Module"; + compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl"; + timestamp = __DATE__, __TIME__; + + aliases { + display = &display; + ipu1 = &ipu1; + }; + + cpus { + /delete-node/ cpu@1; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>; + power-supply = <®_3v3>; + /* + * a poor man's way to create a 1:1 relationship between + * the PWM value and the actual duty cycle + */ + brightness-levels = < 0 1 2 3 4 5 6 7 8 9 + 10 11 12 13 14 15 16 17 18 19 + 20 21 22 23 24 25 26 27 28 29 + 30 31 32 33 34 35 36 37 38 39 + 40 41 42 43 44 45 46 47 48 49 + 50 51 52 53 54 55 56 57 58 59 + 60 61 62 63 64 65 66 67 68 69 + 70 71 72 73 74 75 76 77 78 79 + 80 81 82 83 84 85 86 87 88 89 + 90 91 92 93 94 95 96 97 98 99 + 100>; + default-brightness-level = <50>; + }; + + display: display@di0 { + compatible = "fsl,imx-parallel-display"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_disp0_1>; + interface-pix-fmt = "rgb24"; +// fsl,panel = <&lcd0_panel>; + status = "okay"; + + port { + display0_in: endpoint { + remote-endpoint = <&ipu1_di0_disp0>; + }; + }; + + display-timings { + VGA { + clock-frequency = <25200000>; + hactive = <640>; + vactive = <480>; + hback-porch = <48>; + hsync-len = <96>; + hfront-porch = <16>; + vback-porch = <31>; + vsync-len = <2>; + vfront-porch = <12>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + + ETV570 { + clock-frequency = <25200000>; + hactive = <640>; + vactive = <480>; + hback-porch = <114>; + hsync-len = <30>; + hfront-porch = <16>; + vback-porch = <32>; + vsync-len = <3>; + vfront-porch = <10>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + + ET0350 { + clock-frequency = <6413760>; + hactive = <320>; + vactive = <240>; + hback-porch = <34>; + hsync-len = <34>; + hfront-porch = <20>; + vback-porch = <15>; + vsync-len = <3>; + vfront-porch = <4>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + + ET0430 { + clock-frequency = <9009000>; + hactive = <480>; + vactive = <272>; + hback-porch = <2>; + hsync-len = <41>; + hfront-porch = <2>; + vback-porch = <2>; + vsync-len = <10>; + vfront-porch = <2>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + + ET0500 { + clock-frequency = <33264000>; + hactive = <800>; + vactive = <480>; + hback-porch = <88>; + hsync-len = <128>; + hfront-porch = <40>; + vback-porch = <33>; + vsync-len = <2>; + vfront-porch = <10>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + + ET0700 { /* same as ET0500 */ + clock-frequency = <33264000>; + hactive = <800>; + vactive = <480>; + hback-porch = <88>; + hsync-len = <128>; + hfront-porch = <40>; + vback-porch = <33>; + vsync-len = <2>; + vfront-porch = <10>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + + ETQ570 { + clock-frequency = <6596040>; + hactive = <320>; + vactive = <240>; + hback-porch = <38>; + hsync-len = <30>; + hfront-porch = <30>; + vback-porch = <16>; + vsync-len = <3>; + vfront-porch = <4>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + }; + }; + + lcd0_panel: lcd-panel { + compatible = "edt,et070080dh6", "simple-panel"; + power-supply = <®_lcd0_pwr>; + enable-gpios = <&gpio2 31 GPIO_ACTIVE_HIGH>; + backlight = <&backlight>; + status = "disabled"; + }; +}; + +&ds1339 { + status = "disabled"; +}; + +&pinctrl_hog { + fsl,pins = < + MX6QDL_PAD_EIM_A18__GPIO2_IO20 0x1b0b1 /* LED */ + MX6QDL_PAD_SD3_DAT2__GPIO7_IO06 0x1b0b1 /* ETN PHY RESET */ + MX6QDL_PAD_SD3_DAT4__GPIO7_IO01 0x1b0b1 /* ETN PHY INT */ + MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x1b0b1 /* PWR BTN */ + >; +}; + +&pinctrl_usdhc1 { + fsl,pins = < + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x070b1 + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x07099 + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x070b1 + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x070b1 + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x070b1 + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x070b1 + MX6QDL_PAD_SD3_CMD__GPIO7_IO02 0x170b0 /* SD1 CD */ + >; +}; + +&ipu1_di0_disp0 { + remote-endpoint = <&display0_in>; +}; + +®_lcd0_pwr { + status = "disabled"; +}; + +®_lcd1_pwr { + status = "disabled"; +}; -- 2.1.4 ^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH 2/3] ARM: dts: imx6ul: add support for Ka-Ro electronics TXUL modules 2016-01-12 18:01 ` Lothar Waßmann @ 2016-01-12 18:01 ` Lothar Waßmann -1 siblings, 0 replies; 19+ messages in thread From: Lothar Waßmann @ 2016-01-12 18:01 UTC (permalink / raw) To: linux-arm-kernel Add support for two module variants from Ka-Ro electronics equipped with an i.MX6UL processor running at 528MHz. Both modules are equipped with 256MiB DDR3 SDRAM. The TXUL-0010 has 128MiB NAND flash, while the TXUL-0011 is equipped with 4GiB eMMC. Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de> --- arch/arm/boot/dts/Makefile | 4 +- arch/arm/boot/dts/imx6ul-txul-0010.dts | 54 ++ arch/arm/boot/dts/imx6ul-txul-0011.dts | 85 +++ arch/arm/boot/dts/imx6ul-txul.dtsi | 948 +++++++++++++++++++++++++++++++++ 4 files changed, 1090 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/imx6ul-txul-0010.dts create mode 100644 arch/arm/boot/dts/imx6ul-txul-0011.dts create mode 100644 arch/arm/boot/dts/imx6ul-txul.dtsi diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index ac406d8..d7c3bdd 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -359,7 +359,9 @@ dtb-$(CONFIG_SOC_IMX6SX) += \ imx6sx-sdb-reva.dtb \ imx6sx-sdb.dtb dtb-$(CONFIG_SOC_IMX6UL) += \ - imx6ul-14x14-evk.dtb + imx6ul-14x14-evk.dtb \ + imx6ul-txul-0010.dtb \ + imx6ul-txul-0011.dtb dtb-$(CONFIG_SOC_IMX7D) += \ imx7d-cl-som-imx7.dtb \ imx7d-sbc-imx7.dtb \ diff --git a/arch/arm/boot/dts/imx6ul-txul-0010.dts b/arch/arm/boot/dts/imx6ul-txul-0010.dts new file mode 100644 index 0000000..5e0b09f --- /dev/null +++ b/arch/arm/boot/dts/imx6ul-txul-0010.dts @@ -0,0 +1,54 @@ +/* + * Copyright 2015 Lothar Wa?mann <LW@KARO-electronics.de> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "imx6ul.dtsi" +#include "imx6ul-txul.dtsi" + +/ { + model = "Ka-Ro electronics TXUL-0010 Module"; + compatible = "karo,imx6ul-tx6ul", "fsl,imx6ul"; + + aliases { + mmc0 = &usdhc1; + /delete-property/ mmc1; + }; +}; diff --git a/arch/arm/boot/dts/imx6ul-txul-0011.dts b/arch/arm/boot/dts/imx6ul-txul-0011.dts new file mode 100644 index 0000000..40103ea --- /dev/null +++ b/arch/arm/boot/dts/imx6ul-txul-0011.dts @@ -0,0 +1,85 @@ +/* + * Copyright 2015 Lothar Wa?mann <LW@KARO-electronics.de> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "imx6ul.dtsi" +#include "imx6ul-txul.dtsi" + +/ { + model = "Ka-Ro electronics TXUL-0011 Module"; + compatible = "karo,imx6ul-tx6ul", "fsl,imx6ul"; + + aliases { + mmc0 = &usdhc2; + mmc1 = &usdhc1; + }; +}; + +&gpmi { + status = "disabled"; +}; + +&iomuxc { + imx6qdl-tx6 { + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x070b1 + MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x070b1 + MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x070b1 + MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x070b1 + MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x070b1 + MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x070b1 + /* eMMC RESET */ + MX6UL_PAD_NAND_ALE__USDHC2_RESET_B 0x170b0 + >; + }; + }; +}; + +&usdhc2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc2>; + bus-width = <4>; + no-1-8-v; + non-removable; + fsl,wp-controller; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx6ul-txul.dtsi b/arch/arm/boot/dts/imx6ul-txul.dtsi new file mode 100644 index 0000000..e203999 --- /dev/null +++ b/arch/arm/boot/dts/imx6ul-txul.dtsi @@ -0,0 +1,948 @@ +/* + * Copyright 2015 Lothar Wa?mann <LW@KARO-electronics.de> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/pwm/pwm.h> + +/ { + aliases { + can0 = &can2; + can1 = &can1; + display = &display; + i2c0 = &i2c_gpio; + i2c1 = &i2c2; + lcdif_23bit_pins_a = &pinctrl_disp0_1; + lcdif_24bit_pins_a = &pinctrl_disp0_2; + pwm0 = &pwm5; + reg_can_xcvr = ®_can_xcvr; + serial2 = &uart5; + serial4 = &uart3; + spi0 = &ecspi2; + spi1 = &spi_gpio; + stk5led = &user_led; + usbh1 = &usbotg2; + usbotg = &usbotg1; + }; + + chosen { + stdout-path = &uart1; + }; + + memory { + reg = <0 0>; /* will be filled by U-Boot */ + }; + + clocks { + #address-cells = <1>; + #size-cells = <0>; + mclk: clock at 0 { + compatible = "fixed-clock"; + reg = <0>; + #clock-cells = <0>; + clock-frequency = <27000000>; + }; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&pwm5 0 500000 PWM_POLARITY_INVERTED>; + power-supply = <®_3v3>; + /* + * a poor man's way to create a 1:1 relationship between + * the PWM value and the actual duty cycle + */ + brightness-levels = < 0 1 2 3 4 5 6 7 8 9 + 10 11 12 13 14 15 16 17 18 19 + 20 21 22 23 24 25 26 27 28 29 + 30 31 32 33 34 35 36 37 38 39 + 40 41 42 43 44 45 46 47 48 49 + 50 51 52 53 54 55 56 57 58 59 + 60 61 62 63 64 65 66 67 68 69 + 70 71 72 73 74 75 76 77 78 79 + 80 81 82 83 84 85 86 87 88 89 + 90 91 92 93 94 95 96 97 98 99 + 100>; + default-brightness-level = <50>; + }; + + gpio-keys { + compatible = "gpio-keys"; + }; + + i2c_gpio: i2c-gpio { + compatible = "i2c-gpio"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c_gpio>; + gpios = < + &gpio5 1 GPIO_ACTIVE_HIGH /* SDA */ + &gpio5 0 GPIO_ACTIVE_HIGH /* SCL */ + >; + clock-frequency = <400000>; + status = "okay"; + + ds1339: rtc at 68 { + compatible = "dallas,ds1339"; + reg = <0x68>; + status = "disabled"; + }; + }; + + leds { + compatible = "gpio-leds"; + + user_led: user { + label = "Heartbeat"; + gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + reg_3v3_etn: regulator at 0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "3V3_ETN"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_etnphy_power>; + gpio = <&gpio5 7 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_2v5: regulator at 1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "2V5"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-always-on; + }; + + reg_3v3: regulator at 2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_can_xcvr: regulator at 3 { + compatible = "regulator-fixed"; + reg = <3>; + regulator-name = "CAN XCVR"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan_xcvr>; + gpio = <&gpio3 5 GPIO_ACTIVE_HIGH>; + enable-active-low; + }; + + reg_lcd_pwr: regulator at 5 { + compatible = "regulator-fixed"; + reg = <5>; + regulator-name = "LCD POWER"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcd_pwr>; + gpio = <&gpio5 4 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-boot-on; + regulator-always-on; + }; + + reg_lcd_reset: regulator at 6 { + compatible = "regulator-fixed"; + reg = <6>; + regulator-name = "LCD RESET"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcd_reset>; + gpio = <&gpio3 4 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-boot-on; + regulator-always-on; + }; + + reg_usbh1_vbus: regulator at 7 { + compatible = "regulator-fixed"; + reg = <7>; + regulator-name = "usbh1_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbh1_vbus &pinctrl_usbh1_oc>; + gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_usbotg_vbus: regulator at 8 { + compatible = "regulator-fixed"; + reg = <8>; + regulator-name = "usbotg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg_vbus &pinctrl_usbotg_oc>; + gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + }; + + spi_gpio: spi-gpio { + #address-cells = <1>; + #size-cells = <0>; + compatible = "spi-gpio"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi_gpio>; + gpio-mosi = <&gpio1 30 GPIO_ACTIVE_HIGH>; + gpio-miso = <&gpio1 31 GPIO_ACTIVE_HIGH>; + gpio-sck = <&gpio1 28 GPIO_ACTIVE_HIGH>; + num-chipselects = <2>; + cs-gpios = < + &gpio1 29 GPIO_ACTIVE_HIGH + &gpio1 10 GPIO_ACTIVE_HIGH + >; + status = "disabled"; + + spi at 0 { + compatible = "spidev"; + reg = <0>; + spi-max-frequency = <54000000>; + }; + + spi at 1 { + compatible = "spidev"; + reg = <1>; + spi-max-frequency = <54000000>; + }; + }; + + sound { + compatible = "karo,imx6ul-tx6ul-sgtl5000", + "fsl,imx-audio-sgtl5000"; + model = "imx6ul-tx6ul-sgtl5000-audio"; + ssi-controller = <&sai2>; + audio-codec = <&sgtl5000>; + audio-routing = + "MIC_IN", "Mic Jack", + "Mic Jack", "Mic Bias", + "Headphone Jack", "HP_OUT"; + fsl,no-audmux; + }; +}; + +&can1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan1>; + xceiver-supply = <®_can_xcvr>; + status = "okay"; +}; + +&can2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan2>; + xceiver-supply = <®_can_xcvr>; + status = "okay"; +}; + +&ecspi2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi2>; + fsl,spi-num-chipselects = <2>; + cs-gpios = < + &gpio1 29 GPIO_ACTIVE_HIGH + &gpio1 10 GPIO_ACTIVE_HIGH + >; + status = "okay"; + + spi at 0 { + compatible = "spidev"; + reg = <0>; + spi-max-frequency = <54000000>; + }; + + spi at 1 { + compatible = "spidev"; + reg = <1>; + spi-max-frequency = <54000000>; + }; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet1 &pinctrl_enet_mdio>; + phy-mode = "rmii"; + phy-reset-gpios = <&gpio5 6 GPIO_ACTIVE_HIGH>; + phy-supply = <®_3v3_etn>; + phy-handle = <&etnphy0>; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + etnphy0: ethernet-phy at 0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + interrupt-parent = <&gpio5>; + interrupts = <5>; + status = "okay"; + }; + + etnphy1: ethernet-phy at 1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + status = "okay"; + }; + }; +}; + +&fec2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet2>; + phy-mode = "rmii"; + phy-supply = <®_3v3_etn>; + phy-handle = <&etnphy1>; + status = "disabled"; +}; + +&gpmi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpmi_nand>; + nand-on-flash-bbt; + fsl,no-blockmark-swap; + status = "okay"; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + clock-frequency = <400000>; + status = "okay"; + + sgtl5000: sgtl5000 at 0a { + compatible = "fsl,sgtl5000"; + reg = <0x0a>; + VDDA-supply = <®_2v5>; + VDDIO-supply = <®_3v3>; + clocks = <&mclk>; + }; + + polytouch: edt-ft5x06 at 38 { + compatible = "edt,edt-ft5x06"; + reg = <0x38>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_edt_ft5x06>; + interrupt-parent = <&gpio5>; + interrupts = <2 IRQ_TYPE_EDGE_FALLING>; + reset-gpios = <&gpio5 3 GPIO_ACTIVE_LOW>; + wake-gpios = <&gpio5 8 GPIO_ACTIVE_HIGH>; + linux,wakeup; + }; + + touchscreen: tsc2007 at 48 { + compatible = "ti,tsc2007"; + reg = <0x48>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_tsc2007>; + interrupt-parent = <&gpio3>; + interrupts = <26 0>; + gpios = <&gpio3 26 GPIO_ACTIVE_LOW>; + ti,x-plate-ohms = <660>; + linux,wakeup; + }; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + imx6qdl-tx6 { + pinctrl_hog: hoggrp { + fsl,pins = < + MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x0b0b0 /* LED */ + MX6UL_PAD_SNVS_TAMPER6__GPIO5_IO06 0x0b0b0 /* ETN PHY RESET */ + MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05 0x0b0b0 /* ETN PHY INT */ + >; + }; + + pinctrl_disp0_1: disp0grp-1 { + fsl,pins = < + MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x10 /* LSCLK */ + MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x10 /* OE_ACD */ + MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC 0x10 /* HSYNC */ + MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x10 /* VSYNC */ + /* PAD DISP0_DAT0 is used for the Flexcan transceiver control */ + MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x10 + MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x10 + MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x10 + MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x10 + MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x10 + MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x10 + MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x10 + MX6UL_PAD_LCD_DATA08__LCDIF_DATA08 0x10 + MX6UL_PAD_LCD_DATA09__LCDIF_DATA09 0x10 + MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x10 + MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x10 + MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x10 + MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x10 + MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x10 + MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x10 + MX6UL_PAD_LCD_DATA16__LCDIF_DATA16 0x10 + MX6UL_PAD_LCD_DATA17__LCDIF_DATA17 0x10 + MX6UL_PAD_LCD_DATA18__LCDIF_DATA18 0x10 + MX6UL_PAD_LCD_DATA19__LCDIF_DATA19 0x10 + MX6UL_PAD_LCD_DATA20__LCDIF_DATA20 0x10 + MX6UL_PAD_LCD_DATA21__LCDIF_DATA21 0x10 + MX6UL_PAD_LCD_DATA22__LCDIF_DATA22 0x10 + MX6UL_PAD_LCD_DATA23__LCDIF_DATA23 0x10 + >; + }; + + pinctrl_disp0_2: disp0grp-2 { + fsl,pins = < + MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x10 /* LSCLK */ + MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x10 /* OE_ACD */ + MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC 0x10 /* HSYNC */ + MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x10 /* VSYNC */ + MX6UL_PAD_LCD_DATA00__LCDIF_DATA00 0x10 + MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x10 + MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x10 + MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x10 + MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x10 + MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x10 + MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x10 + MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x10 + MX6UL_PAD_LCD_DATA08__LCDIF_DATA08 0x10 + MX6UL_PAD_LCD_DATA09__LCDIF_DATA09 0x10 + MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x10 + MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x10 + MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x10 + MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x10 + MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x10 + MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x10 + MX6UL_PAD_LCD_DATA16__LCDIF_DATA16 0x10 + MX6UL_PAD_LCD_DATA17__LCDIF_DATA17 0x10 + MX6UL_PAD_LCD_DATA18__LCDIF_DATA18 0x10 + MX6UL_PAD_LCD_DATA19__LCDIF_DATA19 0x10 + MX6UL_PAD_LCD_DATA20__LCDIF_DATA20 0x10 + MX6UL_PAD_LCD_DATA21__LCDIF_DATA21 0x10 + MX6UL_PAD_LCD_DATA22__LCDIF_DATA22 0x10 + MX6UL_PAD_LCD_DATA23__LCDIF_DATA23 0x10 + >; + }; + + pinctrl_ecspi2: ecspi2grp { + fsl,pins = < + MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x0b0b0 /* CSPI_SS */ + MX6UL_PAD_JTAG_MOD__GPIO1_IO10 0x0b0b0 /* CSPI_SS */ + MX6UL_PAD_UART5_TX_DATA__ECSPI2_MOSI 0x0b0b0 /* CSPI_MOSI */ + MX6UL_PAD_UART5_RX_DATA__ECSPI2_MISO 0x0b0b0 /* CSPI_MISO */ + MX6UL_PAD_UART4_TX_DATA__ECSPI2_SCLK 0x0b0b0 /* CSPI_SCLK */ + >; + }; + + pinctrl_edt_ft5x06: edt-ft5x06grp { + fsl,pins = < + MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x1b0b0 /* Interrupt */ + MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03 0x1b0b0 /* Reset */ + MX6UL_PAD_SNVS_TAMPER8__GPIO5_IO08 0x1b0b0 /* Wake */ + >; + }; + + pinctrl_enet1: enet1grp { + fsl,pins = < + MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x0b0b0 + MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x0b0b0 + MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x0b0b0 + MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x0b0b0 + MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x0b0b0 + MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x0b0b0 + MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x0b0b0 + MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x40000031 + >; + }; + + pinctrl_enet2: enet2grp { + fsl,pins = < + MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x0b0b0 + MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x0b0b0 + MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x0b0b0 + MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x0b0b0 + MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x0b0b0 + MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x0b0b0 + MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x0b0b0 + MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x40000031 + >; + }; + + pinctrl_enet_mdio: enet-mdiogrp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO07__ENET1_MDC 0x0b0b0 + MX6UL_PAD_GPIO1_IO06__ENET1_MDIO 0x1b0b0 + >; + }; + + pinctrl_etnphy_power: etnphy-pwrgrp { + fsl,pins = < + MX6UL_PAD_SNVS_TAMPER7__GPIO5_IO07 0x0b0b0 /* ETN PHY POWER */ + >; + }; + + pinctrl_flexcan1: flexcan1grp { + fsl,pins = < + MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX 0x1b0b0 + MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX 0x1b0b0 + >; + }; + + pinctrl_flexcan2: flexcan2grp { + fsl,pins = < + MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX 0x1b0b0 + MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX 0x1b0b0 + >; + }; + + pinctrl_flexcan_xcvr: flexcan-xcvrgrp { + fsl,pins = < + MX6UL_PAD_LCD_DATA00__GPIO3_IO05 0x0b0b0 /* Flexcan XCVR enable */ + >; + }; + + pinctrl_gpmi_nand: gpminandgrp { + fsl,pins = < + MX6UL_PAD_NAND_CLE__RAWNAND_CLE 0x0b0b1 + MX6UL_PAD_NAND_ALE__RAWNAND_ALE 0x0b0b1 + MX6UL_PAD_NAND_WP_B__RAWNAND_WP_B 0x0b0b1 + MX6UL_PAD_NAND_READY_B__RAWNAND_READY_B 0x0b000 + MX6UL_PAD_NAND_CE0_B__RAWNAND_CE0_B 0x0b0b1 + MX6UL_PAD_NAND_RE_B__RAWNAND_RE_B 0x0b0b1 + MX6UL_PAD_NAND_WE_B__RAWNAND_WE_B 0x0b0b1 + MX6UL_PAD_NAND_DATA00__RAWNAND_DATA00 0x0b0b1 + MX6UL_PAD_NAND_DATA01__RAWNAND_DATA01 0x0b0b1 + MX6UL_PAD_NAND_DATA02__RAWNAND_DATA02 0x0b0b1 + MX6UL_PAD_NAND_DATA03__RAWNAND_DATA03 0x0b0b1 + MX6UL_PAD_NAND_DATA04__RAWNAND_DATA04 0x0b0b1 + MX6UL_PAD_NAND_DATA05__RAWNAND_DATA05 0x0b0b1 + MX6UL_PAD_NAND_DATA06__RAWNAND_DATA06 0x0b0b1 + MX6UL_PAD_NAND_DATA07__RAWNAND_DATA07 0x0b0b1 + >; + }; + + pinctrl_i2c_gpio: i2c-gpiogrp { + fsl,pins = < + MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x4001b8b1 /* I2C SCL */ + MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01 0x4001b8b1 /* I2C SDA */ + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO00__I2C2_SCL 0x4001b8b1 + MX6UL_PAD_GPIO1_IO01__I2C2_SDA 0x4001b8b1 + >; + }; + + pinctrl_kpp: kppgrp { + fsl,pins = < + MX6UL_PAD_ENET2_RX_DATA1__KPP_COL04 0x1b0b0 + MX6UL_PAD_ENET2_TX_DATA0__KPP_COL05 0x1b0b0 + MX6UL_PAD_ENET2_TX_EN__KPP_COL06 0x1b0b0 + MX6UL_PAD_ENET2_RX_ER__KPP_COL07 0x1b0b0 + MX6UL_PAD_ENET2_RX_DATA0__KPP_ROW04 0x1b0b0 + MX6UL_PAD_ENET2_RX_EN__KPP_ROW05 0x1b0b0 + MX6UL_PAD_ENET2_TX_DATA1__KPP_ROW06 0x1b0b0 + MX6UL_PAD_ENET2_TX_CLK__KPP_ROW07 0x1b0b0 + >; + }; + + pinctrl_lcd_pwr: lcd-pwrgrp { + fsl,pins = < + MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x0b0b0 /* LCD Power Enable */ + >; + }; + + pinctrl_lcd_reset: lcd-resetgrp { + fsl,pins = < + MX6UL_PAD_LCD_RESET__GPIO3_IO04 0x0b0b0 /* LCD RESET */ + >; + }; + + pinctrl_pwm5: pwm5grp { + fsl,pins = < + MX6UL_PAD_NAND_DQS__PWM5_OUT 0x0b0b0 + >; + }; + + pinctrl_sai2: sai2grp { + fsl,pins = < + MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA 0x0b0b0 /* SSI1_RXD */ + MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA 0x0b0b0 /* SSI1_TXD */ + MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK 0x0b0b0 /* SSI1_CLK */ + MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC 0x0b0b0 /* SSI1_FS */ + >; + }; + + pinctrl_spi_gpio: spi-gpiogrp { + fsl,pins = < + MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x0b0b0 /* CSPI_SS */ + MX6UL_PAD_JTAG_MOD__GPIO1_IO10 0x0b0b0 /* CSPI_SS */ + MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30 0x0b0b0 /* CSPI_MOSI */ + MX6UL_PAD_UART5_RX_DATA__GPIO1_IO31 0x0b0b0 /* CSPI_MISO */ + MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28 0x0b0b0 /* CSPI_SCLK */ + >; + }; + + pinctrl_tsc2007: tsc2007grp { + fsl,pins = < + MX6UL_PAD_JTAG_TMS__GPIO1_IO11 0x1b0b0 /* Interrupt */ + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x0b0b0 + MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x0b0b0 + >; + }; + + pinctrl_uart1_rtscts: uart1_rtsctsgrp { + fsl,pins = < + MX6UL_PAD_UART1_RTS_B__UART1_DCE_RTS 0x0b0b0 + MX6UL_PAD_UART1_CTS_B__UART1_DCE_CTS 0x0b0b0 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX6UL_PAD_UART2_TX_DATA__UART2_DCE_TX 0x0b0b0 + MX6UL_PAD_UART2_RX_DATA__UART2_DCE_RX 0x0b0b0 + >; + }; + + pinctrl_uart2_rtscts: uart2_rtsctsgrp { + fsl,pins = < + MX6UL_PAD_UART3_RX_DATA__UART2_DCE_RTS 0x0b0b0 + MX6UL_PAD_UART3_TX_DATA__UART2_DCE_CTS 0x0b0b0 + >; + }; + + pinctrl_uart5: uart5grp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO04__UART5_DCE_TX 0x0b0b0 + MX6UL_PAD_GPIO1_IO05__UART5_DCE_RX 0x0b0b0 + >; + }; + + pinctrl_uart5_rtscts: uart5_rtsctsgrp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO08__UART5_DCE_RTS 0x0b0b0 + MX6UL_PAD_GPIO1_IO09__UART5_DCE_CTS 0x0b0b0 + >; + }; + + pinctrl_usbh1_oc: usbh1-ocgrp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0x17059 /* USBH1_OC */ + >; + }; + + pinctrl_usbh1_vbus: usbh1-vbusgrp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0x0b0b0 /* USBH1_VBUSEN */ + >; + }; + + pinctrl_usbotg_oc: usbotg-ocgrp { + fsl,pins = < + MX6UL_PAD_UART3_RTS_B__GPIO1_IO27 0x17059 /* USBOTG_OC */ + >; + }; + + pinctrl_usbotg_vbus: usbotg-vbusgrp { + fsl,pins = < + MX6UL_PAD_UART3_CTS_B__GPIO1_IO26 0x1b0b0 /* USBOTG_VBUSEN */ + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x070b1 + MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x07099 + MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x070b1 + MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x070b1 + MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x070b1 + MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x070b1 + /* SD1 CD */ + MX6UL_PAD_NAND_CE1_B__GPIO4_IO14 0x170b0 /* SD1 CD */ + >; + }; + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x070b1 + MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x070b1 + MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x070b1 + MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x070b1 + MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x070b1 + MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x070b1 + /* eMMC RESET */ + MX6UL_PAD_NAND_ALE__USDHC2_RESET_B 0x170b0 + >; + }; + }; +}; + +&kpp { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_kpp>; + /* sample keymap */ + /* row/col 0,1 are mapped to KPP row/col 6,7 */ + linux,keymap = < + MATRIX_KEY(6, 6, KEY_POWER) /* 0x06060074 */ + MATRIX_KEY(6, 7, KEY_KP0) /* 0x06070052 */ + MATRIX_KEY(6, 2, KEY_KP1) /* 0x0602004f */ + MATRIX_KEY(6, 3, KEY_KP2) /* 0x06030050 */ + MATRIX_KEY(7, 6, KEY_KP3) /* 0x07060051 */ + MATRIX_KEY(7, 7, KEY_KP4) /* 0x0707004b */ + MATRIX_KEY(7, 2, KEY_KP5) /* 0x0702004c */ + MATRIX_KEY(7, 3, KEY_KP6) /* 0x0703004d */ + MATRIX_KEY(2, 6, KEY_KP7) /* 0x02060047 */ + MATRIX_KEY(2, 7, KEY_KP8) /* 0x02070048 */ + MATRIX_KEY(2, 2, KEY_KP9) /* 0x02020049 */ + >; + status = "okay"; +}; + +&lcdif { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_disp0_1>; + lcd-supply = <®_lcd_pwr>; + display = <&display>; + status = "okay"; + + display: display at di0 { + bits-per-pixel = <32>; + bus-width = <24>; + status = "okay"; + + display-timings { + VGA { + clock-frequency = <25200000>; + hactive = <640>; + vactive = <480>; + hback-porch = <48>; + hsync-len = <96>; + hfront-porch = <16>; + vback-porch = <31>; + vsync-len = <2>; + vfront-porch = <12>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + + ETV570 { + clock-frequency = <25200000>; + hactive = <640>; + vactive = <480>; + hback-porch = <114>; + hsync-len = <30>; + hfront-porch = <16>; + vback-porch = <32>; + vsync-len = <3>; + vfront-porch = <10>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + + ET0350 { + clock-frequency = <6413760>; + hactive = <320>; + vactive = <240>; + hback-porch = <34>; + hsync-len = <34>; + hfront-porch = <20>; + vback-porch = <15>; + vsync-len = <3>; + vfront-porch = <4>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + + ET0430 { + clock-frequency = <9009000>; + hactive = <480>; + vactive = <272>; + hback-porch = <2>; + hsync-len = <41>; + hfront-porch = <2>; + vback-porch = <2>; + vsync-len = <10>; + vfront-porch = <2>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + + ET0500 { + clock-frequency = <33264000>; + hactive = <800>; + vactive = <480>; + hback-porch = <88>; + hsync-len = <128>; + hfront-porch = <40>; + vback-porch = <33>; + vsync-len = <2>; + vfront-porch = <10>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + + ET0700 { /* same as ET0500 */ + clock-frequency = <33264000>; + hactive = <800>; + vactive = <480>; + hback-porch = <88>; + hsync-len = <128>; + hfront-porch = <40>; + vback-porch = <33>; + vsync-len = <2>; + vfront-porch = <10>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + + ETQ570 { + clock-frequency = <6596040>; + hactive = <320>; + vactive = <240>; + hback-porch = <38>; + hsync-len = <30>; + hfront-porch = <30>; + vback-porch = <16>; + vsync-len = <3>; + vfront-porch = <4>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + }; + }; +}; + +&pwm5 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm5>; + #pwm-cells = <3>; + status = "okay"; +}; + +&sai2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sai2>; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1 &pinctrl_uart1_rtscts>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2 &pinctrl_uart2_rtscts>; + status = "okay"; +}; + +&uart5 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart5 &pinctrl_uart5_rtscts>; + status = "okay"; +}; + +&usbotg2 { + vbus-supply = <®_usbh1_vbus>; + dr_mode = "host"; + disable-over-current; + status = "okay"; +}; + +&usbotg1 { + vbus-supply = <®_usbotg_vbus>; + dr_mode = "peripheral"; + disable-over-current; + status = "okay"; +}; + +&usdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1>; + bus-width = <4>; + no-1-8-v; + cd-gpios = <&gpio4 14 GPIO_ACTIVE_LOW>; + fsl,wp-controller; + status = "okay"; +}; -- 2.1.4 ^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH 2/3] ARM: dts: imx6ul: add support for Ka-Ro electronics TXUL modules @ 2016-01-12 18:01 ` Lothar Waßmann 0 siblings, 0 replies; 19+ messages in thread From: Lothar Waßmann @ 2016-01-12 18:01 UTC (permalink / raw) To: Ian Campbell, Kumar Gala, Mark Rutland, Pawel Moll, Rob Herring, Russell King, Sascha Hauer, Shawn Guo, devicetree, linux-arm-kernel, linux-kernel Cc: Lothar Waßmann Add support for two module variants from Ka-Ro electronics equipped with an i.MX6UL processor running at 528MHz. Both modules are equipped with 256MiB DDR3 SDRAM. The TXUL-0010 has 128MiB NAND flash, while the TXUL-0011 is equipped with 4GiB eMMC. Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> --- arch/arm/boot/dts/Makefile | 4 +- arch/arm/boot/dts/imx6ul-txul-0010.dts | 54 ++ arch/arm/boot/dts/imx6ul-txul-0011.dts | 85 +++ arch/arm/boot/dts/imx6ul-txul.dtsi | 948 +++++++++++++++++++++++++++++++++ 4 files changed, 1090 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/imx6ul-txul-0010.dts create mode 100644 arch/arm/boot/dts/imx6ul-txul-0011.dts create mode 100644 arch/arm/boot/dts/imx6ul-txul.dtsi diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index ac406d8..d7c3bdd 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -359,7 +359,9 @@ dtb-$(CONFIG_SOC_IMX6SX) += \ imx6sx-sdb-reva.dtb \ imx6sx-sdb.dtb dtb-$(CONFIG_SOC_IMX6UL) += \ - imx6ul-14x14-evk.dtb + imx6ul-14x14-evk.dtb \ + imx6ul-txul-0010.dtb \ + imx6ul-txul-0011.dtb dtb-$(CONFIG_SOC_IMX7D) += \ imx7d-cl-som-imx7.dtb \ imx7d-sbc-imx7.dtb \ diff --git a/arch/arm/boot/dts/imx6ul-txul-0010.dts b/arch/arm/boot/dts/imx6ul-txul-0010.dts new file mode 100644 index 0000000..5e0b09f --- /dev/null +++ b/arch/arm/boot/dts/imx6ul-txul-0010.dts @@ -0,0 +1,54 @@ +/* + * Copyright 2015 Lothar Waßmann <LW@KARO-electronics.de> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "imx6ul.dtsi" +#include "imx6ul-txul.dtsi" + +/ { + model = "Ka-Ro electronics TXUL-0010 Module"; + compatible = "karo,imx6ul-tx6ul", "fsl,imx6ul"; + + aliases { + mmc0 = &usdhc1; + /delete-property/ mmc1; + }; +}; diff --git a/arch/arm/boot/dts/imx6ul-txul-0011.dts b/arch/arm/boot/dts/imx6ul-txul-0011.dts new file mode 100644 index 0000000..40103ea --- /dev/null +++ b/arch/arm/boot/dts/imx6ul-txul-0011.dts @@ -0,0 +1,85 @@ +/* + * Copyright 2015 Lothar Waßmann <LW@KARO-electronics.de> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "imx6ul.dtsi" +#include "imx6ul-txul.dtsi" + +/ { + model = "Ka-Ro electronics TXUL-0011 Module"; + compatible = "karo,imx6ul-tx6ul", "fsl,imx6ul"; + + aliases { + mmc0 = &usdhc2; + mmc1 = &usdhc1; + }; +}; + +&gpmi { + status = "disabled"; +}; + +&iomuxc { + imx6qdl-tx6 { + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x070b1 + MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x070b1 + MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x070b1 + MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x070b1 + MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x070b1 + MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x070b1 + /* eMMC RESET */ + MX6UL_PAD_NAND_ALE__USDHC2_RESET_B 0x170b0 + >; + }; + }; +}; + +&usdhc2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc2>; + bus-width = <4>; + no-1-8-v; + non-removable; + fsl,wp-controller; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx6ul-txul.dtsi b/arch/arm/boot/dts/imx6ul-txul.dtsi new file mode 100644 index 0000000..e203999 --- /dev/null +++ b/arch/arm/boot/dts/imx6ul-txul.dtsi @@ -0,0 +1,948 @@ +/* + * Copyright 2015 Lothar Waßmann <LW@KARO-electronics.de> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/pwm/pwm.h> + +/ { + aliases { + can0 = &can2; + can1 = &can1; + display = &display; + i2c0 = &i2c_gpio; + i2c1 = &i2c2; + lcdif_23bit_pins_a = &pinctrl_disp0_1; + lcdif_24bit_pins_a = &pinctrl_disp0_2; + pwm0 = &pwm5; + reg_can_xcvr = ®_can_xcvr; + serial2 = &uart5; + serial4 = &uart3; + spi0 = &ecspi2; + spi1 = &spi_gpio; + stk5led = &user_led; + usbh1 = &usbotg2; + usbotg = &usbotg1; + }; + + chosen { + stdout-path = &uart1; + }; + + memory { + reg = <0 0>; /* will be filled by U-Boot */ + }; + + clocks { + #address-cells = <1>; + #size-cells = <0>; + mclk: clock@0 { + compatible = "fixed-clock"; + reg = <0>; + #clock-cells = <0>; + clock-frequency = <27000000>; + }; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&pwm5 0 500000 PWM_POLARITY_INVERTED>; + power-supply = <®_3v3>; + /* + * a poor man's way to create a 1:1 relationship between + * the PWM value and the actual duty cycle + */ + brightness-levels = < 0 1 2 3 4 5 6 7 8 9 + 10 11 12 13 14 15 16 17 18 19 + 20 21 22 23 24 25 26 27 28 29 + 30 31 32 33 34 35 36 37 38 39 + 40 41 42 43 44 45 46 47 48 49 + 50 51 52 53 54 55 56 57 58 59 + 60 61 62 63 64 65 66 67 68 69 + 70 71 72 73 74 75 76 77 78 79 + 80 81 82 83 84 85 86 87 88 89 + 90 91 92 93 94 95 96 97 98 99 + 100>; + default-brightness-level = <50>; + }; + + gpio-keys { + compatible = "gpio-keys"; + }; + + i2c_gpio: i2c-gpio { + compatible = "i2c-gpio"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c_gpio>; + gpios = < + &gpio5 1 GPIO_ACTIVE_HIGH /* SDA */ + &gpio5 0 GPIO_ACTIVE_HIGH /* SCL */ + >; + clock-frequency = <400000>; + status = "okay"; + + ds1339: rtc@68 { + compatible = "dallas,ds1339"; + reg = <0x68>; + status = "disabled"; + }; + }; + + leds { + compatible = "gpio-leds"; + + user_led: user { + label = "Heartbeat"; + gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + reg_3v3_etn: regulator@0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "3V3_ETN"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_etnphy_power>; + gpio = <&gpio5 7 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_2v5: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "2V5"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-always-on; + }; + + reg_3v3: regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_can_xcvr: regulator@3 { + compatible = "regulator-fixed"; + reg = <3>; + regulator-name = "CAN XCVR"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan_xcvr>; + gpio = <&gpio3 5 GPIO_ACTIVE_HIGH>; + enable-active-low; + }; + + reg_lcd_pwr: regulator@5 { + compatible = "regulator-fixed"; + reg = <5>; + regulator-name = "LCD POWER"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcd_pwr>; + gpio = <&gpio5 4 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-boot-on; + regulator-always-on; + }; + + reg_lcd_reset: regulator@6 { + compatible = "regulator-fixed"; + reg = <6>; + regulator-name = "LCD RESET"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcd_reset>; + gpio = <&gpio3 4 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-boot-on; + regulator-always-on; + }; + + reg_usbh1_vbus: regulator@7 { + compatible = "regulator-fixed"; + reg = <7>; + regulator-name = "usbh1_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbh1_vbus &pinctrl_usbh1_oc>; + gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_usbotg_vbus: regulator@8 { + compatible = "regulator-fixed"; + reg = <8>; + regulator-name = "usbotg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg_vbus &pinctrl_usbotg_oc>; + gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + }; + + spi_gpio: spi-gpio { + #address-cells = <1>; + #size-cells = <0>; + compatible = "spi-gpio"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi_gpio>; + gpio-mosi = <&gpio1 30 GPIO_ACTIVE_HIGH>; + gpio-miso = <&gpio1 31 GPIO_ACTIVE_HIGH>; + gpio-sck = <&gpio1 28 GPIO_ACTIVE_HIGH>; + num-chipselects = <2>; + cs-gpios = < + &gpio1 29 GPIO_ACTIVE_HIGH + &gpio1 10 GPIO_ACTIVE_HIGH + >; + status = "disabled"; + + spi@0 { + compatible = "spidev"; + reg = <0>; + spi-max-frequency = <54000000>; + }; + + spi@1 { + compatible = "spidev"; + reg = <1>; + spi-max-frequency = <54000000>; + }; + }; + + sound { + compatible = "karo,imx6ul-tx6ul-sgtl5000", + "fsl,imx-audio-sgtl5000"; + model = "imx6ul-tx6ul-sgtl5000-audio"; + ssi-controller = <&sai2>; + audio-codec = <&sgtl5000>; + audio-routing = + "MIC_IN", "Mic Jack", + "Mic Jack", "Mic Bias", + "Headphone Jack", "HP_OUT"; + fsl,no-audmux; + }; +}; + +&can1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan1>; + xceiver-supply = <®_can_xcvr>; + status = "okay"; +}; + +&can2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan2>; + xceiver-supply = <®_can_xcvr>; + status = "okay"; +}; + +&ecspi2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi2>; + fsl,spi-num-chipselects = <2>; + cs-gpios = < + &gpio1 29 GPIO_ACTIVE_HIGH + &gpio1 10 GPIO_ACTIVE_HIGH + >; + status = "okay"; + + spi@0 { + compatible = "spidev"; + reg = <0>; + spi-max-frequency = <54000000>; + }; + + spi@1 { + compatible = "spidev"; + reg = <1>; + spi-max-frequency = <54000000>; + }; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet1 &pinctrl_enet_mdio>; + phy-mode = "rmii"; + phy-reset-gpios = <&gpio5 6 GPIO_ACTIVE_HIGH>; + phy-supply = <®_3v3_etn>; + phy-handle = <&etnphy0>; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + etnphy0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + interrupt-parent = <&gpio5>; + interrupts = <5>; + status = "okay"; + }; + + etnphy1: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + status = "okay"; + }; + }; +}; + +&fec2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet2>; + phy-mode = "rmii"; + phy-supply = <®_3v3_etn>; + phy-handle = <&etnphy1>; + status = "disabled"; +}; + +&gpmi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpmi_nand>; + nand-on-flash-bbt; + fsl,no-blockmark-swap; + status = "okay"; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + clock-frequency = <400000>; + status = "okay"; + + sgtl5000: sgtl5000@0a { + compatible = "fsl,sgtl5000"; + reg = <0x0a>; + VDDA-supply = <®_2v5>; + VDDIO-supply = <®_3v3>; + clocks = <&mclk>; + }; + + polytouch: edt-ft5x06@38 { + compatible = "edt,edt-ft5x06"; + reg = <0x38>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_edt_ft5x06>; + interrupt-parent = <&gpio5>; + interrupts = <2 IRQ_TYPE_EDGE_FALLING>; + reset-gpios = <&gpio5 3 GPIO_ACTIVE_LOW>; + wake-gpios = <&gpio5 8 GPIO_ACTIVE_HIGH>; + linux,wakeup; + }; + + touchscreen: tsc2007@48 { + compatible = "ti,tsc2007"; + reg = <0x48>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_tsc2007>; + interrupt-parent = <&gpio3>; + interrupts = <26 0>; + gpios = <&gpio3 26 GPIO_ACTIVE_LOW>; + ti,x-plate-ohms = <660>; + linux,wakeup; + }; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + imx6qdl-tx6 { + pinctrl_hog: hoggrp { + fsl,pins = < + MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x0b0b0 /* LED */ + MX6UL_PAD_SNVS_TAMPER6__GPIO5_IO06 0x0b0b0 /* ETN PHY RESET */ + MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05 0x0b0b0 /* ETN PHY INT */ + >; + }; + + pinctrl_disp0_1: disp0grp-1 { + fsl,pins = < + MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x10 /* LSCLK */ + MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x10 /* OE_ACD */ + MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC 0x10 /* HSYNC */ + MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x10 /* VSYNC */ + /* PAD DISP0_DAT0 is used for the Flexcan transceiver control */ + MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x10 + MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x10 + MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x10 + MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x10 + MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x10 + MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x10 + MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x10 + MX6UL_PAD_LCD_DATA08__LCDIF_DATA08 0x10 + MX6UL_PAD_LCD_DATA09__LCDIF_DATA09 0x10 + MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x10 + MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x10 + MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x10 + MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x10 + MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x10 + MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x10 + MX6UL_PAD_LCD_DATA16__LCDIF_DATA16 0x10 + MX6UL_PAD_LCD_DATA17__LCDIF_DATA17 0x10 + MX6UL_PAD_LCD_DATA18__LCDIF_DATA18 0x10 + MX6UL_PAD_LCD_DATA19__LCDIF_DATA19 0x10 + MX6UL_PAD_LCD_DATA20__LCDIF_DATA20 0x10 + MX6UL_PAD_LCD_DATA21__LCDIF_DATA21 0x10 + MX6UL_PAD_LCD_DATA22__LCDIF_DATA22 0x10 + MX6UL_PAD_LCD_DATA23__LCDIF_DATA23 0x10 + >; + }; + + pinctrl_disp0_2: disp0grp-2 { + fsl,pins = < + MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x10 /* LSCLK */ + MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x10 /* OE_ACD */ + MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC 0x10 /* HSYNC */ + MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x10 /* VSYNC */ + MX6UL_PAD_LCD_DATA00__LCDIF_DATA00 0x10 + MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x10 + MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x10 + MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x10 + MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x10 + MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x10 + MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x10 + MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x10 + MX6UL_PAD_LCD_DATA08__LCDIF_DATA08 0x10 + MX6UL_PAD_LCD_DATA09__LCDIF_DATA09 0x10 + MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x10 + MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x10 + MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x10 + MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x10 + MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x10 + MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x10 + MX6UL_PAD_LCD_DATA16__LCDIF_DATA16 0x10 + MX6UL_PAD_LCD_DATA17__LCDIF_DATA17 0x10 + MX6UL_PAD_LCD_DATA18__LCDIF_DATA18 0x10 + MX6UL_PAD_LCD_DATA19__LCDIF_DATA19 0x10 + MX6UL_PAD_LCD_DATA20__LCDIF_DATA20 0x10 + MX6UL_PAD_LCD_DATA21__LCDIF_DATA21 0x10 + MX6UL_PAD_LCD_DATA22__LCDIF_DATA22 0x10 + MX6UL_PAD_LCD_DATA23__LCDIF_DATA23 0x10 + >; + }; + + pinctrl_ecspi2: ecspi2grp { + fsl,pins = < + MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x0b0b0 /* CSPI_SS */ + MX6UL_PAD_JTAG_MOD__GPIO1_IO10 0x0b0b0 /* CSPI_SS */ + MX6UL_PAD_UART5_TX_DATA__ECSPI2_MOSI 0x0b0b0 /* CSPI_MOSI */ + MX6UL_PAD_UART5_RX_DATA__ECSPI2_MISO 0x0b0b0 /* CSPI_MISO */ + MX6UL_PAD_UART4_TX_DATA__ECSPI2_SCLK 0x0b0b0 /* CSPI_SCLK */ + >; + }; + + pinctrl_edt_ft5x06: edt-ft5x06grp { + fsl,pins = < + MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x1b0b0 /* Interrupt */ + MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03 0x1b0b0 /* Reset */ + MX6UL_PAD_SNVS_TAMPER8__GPIO5_IO08 0x1b0b0 /* Wake */ + >; + }; + + pinctrl_enet1: enet1grp { + fsl,pins = < + MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x0b0b0 + MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x0b0b0 + MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x0b0b0 + MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x0b0b0 + MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x0b0b0 + MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x0b0b0 + MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x0b0b0 + MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x40000031 + >; + }; + + pinctrl_enet2: enet2grp { + fsl,pins = < + MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x0b0b0 + MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x0b0b0 + MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x0b0b0 + MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x0b0b0 + MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x0b0b0 + MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x0b0b0 + MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x0b0b0 + MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x40000031 + >; + }; + + pinctrl_enet_mdio: enet-mdiogrp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO07__ENET1_MDC 0x0b0b0 + MX6UL_PAD_GPIO1_IO06__ENET1_MDIO 0x1b0b0 + >; + }; + + pinctrl_etnphy_power: etnphy-pwrgrp { + fsl,pins = < + MX6UL_PAD_SNVS_TAMPER7__GPIO5_IO07 0x0b0b0 /* ETN PHY POWER */ + >; + }; + + pinctrl_flexcan1: flexcan1grp { + fsl,pins = < + MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX 0x1b0b0 + MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX 0x1b0b0 + >; + }; + + pinctrl_flexcan2: flexcan2grp { + fsl,pins = < + MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX 0x1b0b0 + MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX 0x1b0b0 + >; + }; + + pinctrl_flexcan_xcvr: flexcan-xcvrgrp { + fsl,pins = < + MX6UL_PAD_LCD_DATA00__GPIO3_IO05 0x0b0b0 /* Flexcan XCVR enable */ + >; + }; + + pinctrl_gpmi_nand: gpminandgrp { + fsl,pins = < + MX6UL_PAD_NAND_CLE__RAWNAND_CLE 0x0b0b1 + MX6UL_PAD_NAND_ALE__RAWNAND_ALE 0x0b0b1 + MX6UL_PAD_NAND_WP_B__RAWNAND_WP_B 0x0b0b1 + MX6UL_PAD_NAND_READY_B__RAWNAND_READY_B 0x0b000 + MX6UL_PAD_NAND_CE0_B__RAWNAND_CE0_B 0x0b0b1 + MX6UL_PAD_NAND_RE_B__RAWNAND_RE_B 0x0b0b1 + MX6UL_PAD_NAND_WE_B__RAWNAND_WE_B 0x0b0b1 + MX6UL_PAD_NAND_DATA00__RAWNAND_DATA00 0x0b0b1 + MX6UL_PAD_NAND_DATA01__RAWNAND_DATA01 0x0b0b1 + MX6UL_PAD_NAND_DATA02__RAWNAND_DATA02 0x0b0b1 + MX6UL_PAD_NAND_DATA03__RAWNAND_DATA03 0x0b0b1 + MX6UL_PAD_NAND_DATA04__RAWNAND_DATA04 0x0b0b1 + MX6UL_PAD_NAND_DATA05__RAWNAND_DATA05 0x0b0b1 + MX6UL_PAD_NAND_DATA06__RAWNAND_DATA06 0x0b0b1 + MX6UL_PAD_NAND_DATA07__RAWNAND_DATA07 0x0b0b1 + >; + }; + + pinctrl_i2c_gpio: i2c-gpiogrp { + fsl,pins = < + MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x4001b8b1 /* I2C SCL */ + MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01 0x4001b8b1 /* I2C SDA */ + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO00__I2C2_SCL 0x4001b8b1 + MX6UL_PAD_GPIO1_IO01__I2C2_SDA 0x4001b8b1 + >; + }; + + pinctrl_kpp: kppgrp { + fsl,pins = < + MX6UL_PAD_ENET2_RX_DATA1__KPP_COL04 0x1b0b0 + MX6UL_PAD_ENET2_TX_DATA0__KPP_COL05 0x1b0b0 + MX6UL_PAD_ENET2_TX_EN__KPP_COL06 0x1b0b0 + MX6UL_PAD_ENET2_RX_ER__KPP_COL07 0x1b0b0 + MX6UL_PAD_ENET2_RX_DATA0__KPP_ROW04 0x1b0b0 + MX6UL_PAD_ENET2_RX_EN__KPP_ROW05 0x1b0b0 + MX6UL_PAD_ENET2_TX_DATA1__KPP_ROW06 0x1b0b0 + MX6UL_PAD_ENET2_TX_CLK__KPP_ROW07 0x1b0b0 + >; + }; + + pinctrl_lcd_pwr: lcd-pwrgrp { + fsl,pins = < + MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x0b0b0 /* LCD Power Enable */ + >; + }; + + pinctrl_lcd_reset: lcd-resetgrp { + fsl,pins = < + MX6UL_PAD_LCD_RESET__GPIO3_IO04 0x0b0b0 /* LCD RESET */ + >; + }; + + pinctrl_pwm5: pwm5grp { + fsl,pins = < + MX6UL_PAD_NAND_DQS__PWM5_OUT 0x0b0b0 + >; + }; + + pinctrl_sai2: sai2grp { + fsl,pins = < + MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA 0x0b0b0 /* SSI1_RXD */ + MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA 0x0b0b0 /* SSI1_TXD */ + MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK 0x0b0b0 /* SSI1_CLK */ + MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC 0x0b0b0 /* SSI1_FS */ + >; + }; + + pinctrl_spi_gpio: spi-gpiogrp { + fsl,pins = < + MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x0b0b0 /* CSPI_SS */ + MX6UL_PAD_JTAG_MOD__GPIO1_IO10 0x0b0b0 /* CSPI_SS */ + MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30 0x0b0b0 /* CSPI_MOSI */ + MX6UL_PAD_UART5_RX_DATA__GPIO1_IO31 0x0b0b0 /* CSPI_MISO */ + MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28 0x0b0b0 /* CSPI_SCLK */ + >; + }; + + pinctrl_tsc2007: tsc2007grp { + fsl,pins = < + MX6UL_PAD_JTAG_TMS__GPIO1_IO11 0x1b0b0 /* Interrupt */ + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x0b0b0 + MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x0b0b0 + >; + }; + + pinctrl_uart1_rtscts: uart1_rtsctsgrp { + fsl,pins = < + MX6UL_PAD_UART1_RTS_B__UART1_DCE_RTS 0x0b0b0 + MX6UL_PAD_UART1_CTS_B__UART1_DCE_CTS 0x0b0b0 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX6UL_PAD_UART2_TX_DATA__UART2_DCE_TX 0x0b0b0 + MX6UL_PAD_UART2_RX_DATA__UART2_DCE_RX 0x0b0b0 + >; + }; + + pinctrl_uart2_rtscts: uart2_rtsctsgrp { + fsl,pins = < + MX6UL_PAD_UART3_RX_DATA__UART2_DCE_RTS 0x0b0b0 + MX6UL_PAD_UART3_TX_DATA__UART2_DCE_CTS 0x0b0b0 + >; + }; + + pinctrl_uart5: uart5grp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO04__UART5_DCE_TX 0x0b0b0 + MX6UL_PAD_GPIO1_IO05__UART5_DCE_RX 0x0b0b0 + >; + }; + + pinctrl_uart5_rtscts: uart5_rtsctsgrp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO08__UART5_DCE_RTS 0x0b0b0 + MX6UL_PAD_GPIO1_IO09__UART5_DCE_CTS 0x0b0b0 + >; + }; + + pinctrl_usbh1_oc: usbh1-ocgrp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0x17059 /* USBH1_OC */ + >; + }; + + pinctrl_usbh1_vbus: usbh1-vbusgrp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0x0b0b0 /* USBH1_VBUSEN */ + >; + }; + + pinctrl_usbotg_oc: usbotg-ocgrp { + fsl,pins = < + MX6UL_PAD_UART3_RTS_B__GPIO1_IO27 0x17059 /* USBOTG_OC */ + >; + }; + + pinctrl_usbotg_vbus: usbotg-vbusgrp { + fsl,pins = < + MX6UL_PAD_UART3_CTS_B__GPIO1_IO26 0x1b0b0 /* USBOTG_VBUSEN */ + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x070b1 + MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x07099 + MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x070b1 + MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x070b1 + MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x070b1 + MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x070b1 + /* SD1 CD */ + MX6UL_PAD_NAND_CE1_B__GPIO4_IO14 0x170b0 /* SD1 CD */ + >; + }; + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x070b1 + MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x070b1 + MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x070b1 + MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x070b1 + MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x070b1 + MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x070b1 + /* eMMC RESET */ + MX6UL_PAD_NAND_ALE__USDHC2_RESET_B 0x170b0 + >; + }; + }; +}; + +&kpp { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_kpp>; + /* sample keymap */ + /* row/col 0,1 are mapped to KPP row/col 6,7 */ + linux,keymap = < + MATRIX_KEY(6, 6, KEY_POWER) /* 0x06060074 */ + MATRIX_KEY(6, 7, KEY_KP0) /* 0x06070052 */ + MATRIX_KEY(6, 2, KEY_KP1) /* 0x0602004f */ + MATRIX_KEY(6, 3, KEY_KP2) /* 0x06030050 */ + MATRIX_KEY(7, 6, KEY_KP3) /* 0x07060051 */ + MATRIX_KEY(7, 7, KEY_KP4) /* 0x0707004b */ + MATRIX_KEY(7, 2, KEY_KP5) /* 0x0702004c */ + MATRIX_KEY(7, 3, KEY_KP6) /* 0x0703004d */ + MATRIX_KEY(2, 6, KEY_KP7) /* 0x02060047 */ + MATRIX_KEY(2, 7, KEY_KP8) /* 0x02070048 */ + MATRIX_KEY(2, 2, KEY_KP9) /* 0x02020049 */ + >; + status = "okay"; +}; + +&lcdif { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_disp0_1>; + lcd-supply = <®_lcd_pwr>; + display = <&display>; + status = "okay"; + + display: display@di0 { + bits-per-pixel = <32>; + bus-width = <24>; + status = "okay"; + + display-timings { + VGA { + clock-frequency = <25200000>; + hactive = <640>; + vactive = <480>; + hback-porch = <48>; + hsync-len = <96>; + hfront-porch = <16>; + vback-porch = <31>; + vsync-len = <2>; + vfront-porch = <12>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + + ETV570 { + clock-frequency = <25200000>; + hactive = <640>; + vactive = <480>; + hback-porch = <114>; + hsync-len = <30>; + hfront-porch = <16>; + vback-porch = <32>; + vsync-len = <3>; + vfront-porch = <10>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + + ET0350 { + clock-frequency = <6413760>; + hactive = <320>; + vactive = <240>; + hback-porch = <34>; + hsync-len = <34>; + hfront-porch = <20>; + vback-porch = <15>; + vsync-len = <3>; + vfront-porch = <4>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + + ET0430 { + clock-frequency = <9009000>; + hactive = <480>; + vactive = <272>; + hback-porch = <2>; + hsync-len = <41>; + hfront-porch = <2>; + vback-porch = <2>; + vsync-len = <10>; + vfront-porch = <2>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + + ET0500 { + clock-frequency = <33264000>; + hactive = <800>; + vactive = <480>; + hback-porch = <88>; + hsync-len = <128>; + hfront-porch = <40>; + vback-porch = <33>; + vsync-len = <2>; + vfront-porch = <10>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + + ET0700 { /* same as ET0500 */ + clock-frequency = <33264000>; + hactive = <800>; + vactive = <480>; + hback-porch = <88>; + hsync-len = <128>; + hfront-porch = <40>; + vback-porch = <33>; + vsync-len = <2>; + vfront-porch = <10>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + + ETQ570 { + clock-frequency = <6596040>; + hactive = <320>; + vactive = <240>; + hback-porch = <38>; + hsync-len = <30>; + hfront-porch = <30>; + vback-porch = <16>; + vsync-len = <3>; + vfront-porch = <4>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + }; + }; +}; + +&pwm5 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm5>; + #pwm-cells = <3>; + status = "okay"; +}; + +&sai2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sai2>; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1 &pinctrl_uart1_rtscts>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2 &pinctrl_uart2_rtscts>; + status = "okay"; +}; + +&uart5 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart5 &pinctrl_uart5_rtscts>; + status = "okay"; +}; + +&usbotg2 { + vbus-supply = <®_usbh1_vbus>; + dr_mode = "host"; + disable-over-current; + status = "okay"; +}; + +&usbotg1 { + vbus-supply = <®_usbotg_vbus>; + dr_mode = "peripheral"; + disable-over-current; + status = "okay"; +}; + +&usdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1>; + bus-width = <4>; + no-1-8-v; + cd-gpios = <&gpio4 14 GPIO_ACTIVE_LOW>; + fsl,wp-controller; + status = "okay"; +}; -- 2.1.4 ^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH 3/3] ARM: dts: imx6: add display timing for NL12880BC20 display to Ka-Ro electronics TX6 LVDS modules 2016-01-12 18:01 ` Lothar Waßmann @ 2016-01-12 18:01 ` Lothar Waßmann -1 siblings, 0 replies; 19+ messages in thread From: Lothar Waßmann @ 2016-01-12 18:01 UTC (permalink / raw) To: linux-arm-kernel Add support for the NLT Technologies WXGA LVDS display NL12880BC20 to the TX6 LVDS modules from Ka-Ro electronics. Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de> --- arch/arm/boot/dts/imx6dl-tx6u-811x.dts | 42 ++++++++++++++++++++++++++++++---- arch/arm/boot/dts/imx6q-tx6q-1110.dts | 42 ++++++++++++++++++++++++++++++---- 2 files changed, 76 insertions(+), 8 deletions(-) diff --git a/arch/arm/boot/dts/imx6dl-tx6u-811x.dts b/arch/arm/boot/dts/imx6dl-tx6u-811x.dts index c275eec..c14ee8f 100644 --- a/arch/arm/boot/dts/imx6dl-tx6u-811x.dts +++ b/arch/arm/boot/dts/imx6dl-tx6u-811x.dts @@ -104,8 +104,9 @@ status = "okay"; display-timings { - native-mode = <&lvds_timing0>; - lvds_timing0: hsd100pxn1 { + native-mode = <&lvds0_timing0>; + + lvds0_timing0: hsd100pxn1 { clock-frequency = <65000000>; hactive = <1024>; vactive = <768>; @@ -118,6 +119,22 @@ de-active = <1>; pixelclk-active = <1>; }; + + lvds0_timing1: nl12880bc20 { + clock-frequency = <71000000>; + hactive = <1280>; + vactive = <800>; + hback-porch = <50>; + hsync-len = <60>; + hfront-porch = <50>; + vback-porch = <5>; + vsync-len = <13>; + vfront-porch = <5>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; }; }; @@ -127,8 +144,9 @@ status = "disabled"; display-timings { - native-mode = <&lvds_timing1>; - lvds_timing1: hsd100pxn1 { + native-mode = <&lvds1_timing0>; + + lvds1_timing0: hsd100pxn1 { clock-frequency = <65000000>; hactive = <1024>; vactive = <768>; @@ -141,6 +159,22 @@ de-active = <1>; pixelclk-active = <1>; }; + + lvds1_timing1: nl12880bc20 { + clock-frequency = <71000000>; + hactive = <1280>; + vactive = <800>; + hback-porch = <50>; + hsync-len = <60>; + hfront-porch = <50>; + vback-porch = <5>; + vsync-len = <13>; + vfront-porch = <5>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; }; }; }; diff --git a/arch/arm/boot/dts/imx6q-tx6q-1110.dts b/arch/arm/boot/dts/imx6q-tx6q-1110.dts index 88aa1e4..7a8be02 100644 --- a/arch/arm/boot/dts/imx6q-tx6q-1110.dts +++ b/arch/arm/boot/dts/imx6q-tx6q-1110.dts @@ -104,8 +104,9 @@ status = "okay"; display-timings { - native-mode = <&lvds_timing0>; - lvds_timing0: hsd100pxn1 { + native-mode = <&lvds0_timing0>; + + lvds0_timing0: hsd100pxn1 { clock-frequency = <65000000>; hactive = <1024>; vactive = <768>; @@ -118,6 +119,22 @@ de-active = <1>; pixelclk-active = <1>; }; + + lvds0_timing1: nl12880bc20 { + clock-frequency = <71000000>; + hactive = <1280>; + vactive = <800>; + hback-porch = <50>; + hsync-len = <60>; + hfront-porch = <50>; + vback-porch = <5>; + vsync-len = <13>; + vfront-porch = <5>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; }; }; @@ -127,8 +144,9 @@ status = "disabled"; display-timings { - native-mode = <&lvds_timing1>; - lvds_timing1: hsd100pxn1 { + native-mode = <&lvds1_timing0>; + + lvds1_timing0: hsd100pxn1 { clock-frequency = <65000000>; hactive = <1024>; vactive = <768>; @@ -141,6 +159,22 @@ de-active = <1>; pixelclk-active = <1>; }; + + lvds1_timing1: nl12880bc20 { + clock-frequency = <71000000>; + hactive = <1280>; + vactive = <800>; + hback-porch = <50>; + hsync-len = <60>; + hfront-porch = <50>; + vback-porch = <5>; + vsync-len = <13>; + vfront-porch = <5>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; }; }; }; -- 2.1.4 ^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH 3/3] ARM: dts: imx6: add display timing for NL12880BC20 display to Ka-Ro electronics TX6 LVDS modules @ 2016-01-12 18:01 ` Lothar Waßmann 0 siblings, 0 replies; 19+ messages in thread From: Lothar Waßmann @ 2016-01-12 18:01 UTC (permalink / raw) To: Ian Campbell, Kumar Gala, Mark Rutland, Pawel Moll, Rob Herring, Russell King, Sascha Hauer, Shawn Guo, devicetree, linux-arm-kernel, linux-kernel Cc: Lothar Waßmann Add support for the NLT Technologies WXGA LVDS display NL12880BC20 to the TX6 LVDS modules from Ka-Ro electronics. Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> --- arch/arm/boot/dts/imx6dl-tx6u-811x.dts | 42 ++++++++++++++++++++++++++++++---- arch/arm/boot/dts/imx6q-tx6q-1110.dts | 42 ++++++++++++++++++++++++++++++---- 2 files changed, 76 insertions(+), 8 deletions(-) diff --git a/arch/arm/boot/dts/imx6dl-tx6u-811x.dts b/arch/arm/boot/dts/imx6dl-tx6u-811x.dts index c275eec..c14ee8f 100644 --- a/arch/arm/boot/dts/imx6dl-tx6u-811x.dts +++ b/arch/arm/boot/dts/imx6dl-tx6u-811x.dts @@ -104,8 +104,9 @@ status = "okay"; display-timings { - native-mode = <&lvds_timing0>; - lvds_timing0: hsd100pxn1 { + native-mode = <&lvds0_timing0>; + + lvds0_timing0: hsd100pxn1 { clock-frequency = <65000000>; hactive = <1024>; vactive = <768>; @@ -118,6 +119,22 @@ de-active = <1>; pixelclk-active = <1>; }; + + lvds0_timing1: nl12880bc20 { + clock-frequency = <71000000>; + hactive = <1280>; + vactive = <800>; + hback-porch = <50>; + hsync-len = <60>; + hfront-porch = <50>; + vback-porch = <5>; + vsync-len = <13>; + vfront-porch = <5>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; }; }; @@ -127,8 +144,9 @@ status = "disabled"; display-timings { - native-mode = <&lvds_timing1>; - lvds_timing1: hsd100pxn1 { + native-mode = <&lvds1_timing0>; + + lvds1_timing0: hsd100pxn1 { clock-frequency = <65000000>; hactive = <1024>; vactive = <768>; @@ -141,6 +159,22 @@ de-active = <1>; pixelclk-active = <1>; }; + + lvds1_timing1: nl12880bc20 { + clock-frequency = <71000000>; + hactive = <1280>; + vactive = <800>; + hback-porch = <50>; + hsync-len = <60>; + hfront-porch = <50>; + vback-porch = <5>; + vsync-len = <13>; + vfront-porch = <5>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; }; }; }; diff --git a/arch/arm/boot/dts/imx6q-tx6q-1110.dts b/arch/arm/boot/dts/imx6q-tx6q-1110.dts index 88aa1e4..7a8be02 100644 --- a/arch/arm/boot/dts/imx6q-tx6q-1110.dts +++ b/arch/arm/boot/dts/imx6q-tx6q-1110.dts @@ -104,8 +104,9 @@ status = "okay"; display-timings { - native-mode = <&lvds_timing0>; - lvds_timing0: hsd100pxn1 { + native-mode = <&lvds0_timing0>; + + lvds0_timing0: hsd100pxn1 { clock-frequency = <65000000>; hactive = <1024>; vactive = <768>; @@ -118,6 +119,22 @@ de-active = <1>; pixelclk-active = <1>; }; + + lvds0_timing1: nl12880bc20 { + clock-frequency = <71000000>; + hactive = <1280>; + vactive = <800>; + hback-porch = <50>; + hsync-len = <60>; + hfront-porch = <50>; + vback-porch = <5>; + vsync-len = <13>; + vfront-porch = <5>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; }; }; @@ -127,8 +144,9 @@ status = "disabled"; display-timings { - native-mode = <&lvds_timing1>; - lvds_timing1: hsd100pxn1 { + native-mode = <&lvds1_timing0>; + + lvds1_timing0: hsd100pxn1 { clock-frequency = <65000000>; hactive = <1024>; vactive = <768>; @@ -141,6 +159,22 @@ de-active = <1>; pixelclk-active = <1>; }; + + lvds1_timing1: nl12880bc20 { + clock-frequency = <71000000>; + hactive = <1280>; + vactive = <800>; + hback-porch = <50>; + hsync-len = <60>; + hfront-porch = <50>; + vback-porch = <5>; + vsync-len = <13>; + vfront-porch = <5>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; }; }; }; -- 2.1.4 ^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH 2/3] ARM: dts: imx6ul: add support for Ka-Ro electronics TXUL modules @ 2016-01-12 18:43 ` Fabio Estevam 0 siblings, 0 replies; 19+ messages in thread From: Fabio Estevam @ 2016-01-12 18:43 UTC (permalink / raw) To: linux-arm-kernel On Tue, Jan 12, 2016 at 4:01 PM, Lothar Wa?mann <LW@karo-electronics.de> wrote: > + spi at 0 { > + compatible = "spidev"; > + reg = <0>; > + spi-max-frequency = <54000000>; > + }; > + > + spi at 1 { > + compatible = "spidev"; > + reg = <1>; > + spi-max-frequency = <54000000>; > + }; > + }; If you leave the spidev node, the spi core will complain loudly about it. ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH 2/3] ARM: dts: imx6ul: add support for Ka-Ro electronics TXUL modules @ 2016-01-12 18:43 ` Fabio Estevam 0 siblings, 0 replies; 19+ messages in thread From: Fabio Estevam @ 2016-01-12 18:43 UTC (permalink / raw) To: Lothar Waßmann Cc: Ian Campbell, Kumar Gala, Mark Rutland, Pawel Moll, Rob Herring, Russell King, Sascha Hauer, Shawn Guo, devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-kernel On Tue, Jan 12, 2016 at 4:01 PM, Lothar Waßmann <LW@karo-electronics.de> wrote: > + spi@0 { > + compatible = "spidev"; > + reg = <0>; > + spi-max-frequency = <54000000>; > + }; > + > + spi@1 { > + compatible = "spidev"; > + reg = <1>; > + spi-max-frequency = <54000000>; > + }; > + }; If you leave the spidev node, the spi core will complain loudly about it. ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH 2/3] ARM: dts: imx6ul: add support for Ka-Ro electronics TXUL modules @ 2016-01-12 18:43 ` Fabio Estevam 0 siblings, 0 replies; 19+ messages in thread From: Fabio Estevam @ 2016-01-12 18:43 UTC (permalink / raw) To: Lothar Waßmann Cc: Ian Campbell, Kumar Gala, Mark Rutland, Pawel Moll, Rob Herring, Russell King, Sascha Hauer, Shawn Guo, devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org, linux-kernel On Tue, Jan 12, 2016 at 4:01 PM, Lothar Waßmann <LW@karo-electronics.de> wrote: > + spi@0 { > + compatible = "spidev"; > + reg = <0>; > + spi-max-frequency = <54000000>; > + }; > + > + spi@1 { > + compatible = "spidev"; > + reg = <1>; > + spi-max-frequency = <54000000>; > + }; > + }; If you leave the spidev node, the spi core will complain loudly about it. -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH 2/3] ARM: dts: imx6ul: add support for Ka-Ro electronics TXUL modules @ 2016-01-13 11:36 ` Lothar Waßmann 0 siblings, 0 replies; 19+ messages in thread From: Lothar Waßmann @ 2016-01-13 11:36 UTC (permalink / raw) To: linux-arm-kernel Hi, > On Tue, Jan 12, 2016 at 4:01 PM, Lothar Wa?mann <LW@karo-electronics.de> wrote: > > > + spi at 0 { > > + compatible = "spidev"; > > + reg = <0>; > > + spi-max-frequency = <54000000>; > > + }; > > + > > + spi at 1 { > > + compatible = "spidev"; > > + reg = <1>; > > + spi-max-frequency = <54000000>; > > + }; > > + }; > > If you leave the spidev node, the spi core will complain loudly about it. > I know. But this gives the opportunity to test the SPI interface without any bogus chip definitions. Lothar Wa?mann ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH 2/3] ARM: dts: imx6ul: add support for Ka-Ro electronics TXUL modules @ 2016-01-13 11:36 ` Lothar Waßmann 0 siblings, 0 replies; 19+ messages in thread From: Lothar Waßmann @ 2016-01-13 11:36 UTC (permalink / raw) To: Fabio Estevam Cc: Ian Campbell, Kumar Gala, Mark Rutland, Pawel Moll, Rob Herring, Russell King, Sascha Hauer, Shawn Guo, devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-kernel Hi, > On Tue, Jan 12, 2016 at 4:01 PM, Lothar Waßmann <LW@karo-electronics.de> wrote: > > > + spi@0 { > > + compatible = "spidev"; > > + reg = <0>; > > + spi-max-frequency = <54000000>; > > + }; > > + > > + spi@1 { > > + compatible = "spidev"; > > + reg = <1>; > > + spi-max-frequency = <54000000>; > > + }; > > + }; > > If you leave the spidev node, the spi core will complain loudly about it. > I know. But this gives the opportunity to test the SPI interface without any bogus chip definitions. Lothar Waßmann ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH 2/3] ARM: dts: imx6ul: add support for Ka-Ro electronics TXUL modules @ 2016-01-13 11:36 ` Lothar Waßmann 0 siblings, 0 replies; 19+ messages in thread From: Lothar Waßmann @ 2016-01-13 11:36 UTC (permalink / raw) To: Fabio Estevam Cc: Ian Campbell, Kumar Gala, Mark Rutland, Pawel Moll, Rob Herring, Russell King, Sascha Hauer, Shawn Guo, devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org, linux-kernel Hi, > On Tue, Jan 12, 2016 at 4:01 PM, Lothar Waßmann <LW@karo-electronics.de> wrote: > > > + spi@0 { > > + compatible = "spidev"; > > + reg = <0>; > > + spi-max-frequency = <54000000>; > > + }; > > + > > + spi@1 { > > + compatible = "spidev"; > > + reg = <1>; > > + spi-max-frequency = <54000000>; > > + }; > > + }; > > If you leave the spidev node, the spi core will complain loudly about it. > I know. But this gives the opportunity to test the SPI interface without any bogus chip definitions. Lothar Waßmann -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH 1/3] ARM: dts: imx6: add support for Ka-Ro electronics TX6S-8034 module @ 2016-01-13 7:35 ` Holger Schurig 0 siblings, 0 replies; 19+ messages in thread From: Holger Schurig @ 2016-01-13 7:35 UTC (permalink / raw) To: linux-arm-kernel Lothar Wa?mann <LW@KARO-electronics.de> writes: > +/ { > + model = "Ka-Ro electronics TX6S-8034 Module"; > + compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl"; > + timestamp = __DATE__, __TIME__; Is this needed or useful? There's a movement that aims to do "reproducible builds" ... being able to recompile an image and verify it against the supplied can be helpful for security audit purposes. > + display: display at di0 { > + compatible = "fsl,imx-parallel-display"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_disp0_1>; > + interface-pix-fmt = "rgb24"; > +// fsl,panel = <&lcd0_panel>; Probably not for upstream inclusion? ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH 1/3] ARM: dts: imx6: add support for Ka-Ro electronics TX6S-8034 module @ 2016-01-13 7:35 ` Holger Schurig 0 siblings, 0 replies; 19+ messages in thread From: Holger Schurig @ 2016-01-13 7:35 UTC (permalink / raw) To: Lothar Waßmann Cc: Ian Campbell, Kumar Gala, Mark Rutland, Pawel Moll, Rob Herring, Russell King, Sascha Hauer, Shawn Guo, devicetree, linux-arm-kernel, linux-kernel Lothar Waßmann <LW@KARO-electronics.de> writes: > +/ { > + model = "Ka-Ro electronics TX6S-8034 Module"; > + compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl"; > + timestamp = __DATE__, __TIME__; Is this needed or useful? There's a movement that aims to do "reproducible builds" ... being able to recompile an image and verify it against the supplied can be helpful for security audit purposes. > + display: display@di0 { > + compatible = "fsl,imx-parallel-display"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_disp0_1>; > + interface-pix-fmt = "rgb24"; > +// fsl,panel = <&lcd0_panel>; Probably not for upstream inclusion? ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH 1/3] ARM: dts: imx6: add support for Ka-Ro electronics TX6S-8034 module @ 2016-01-13 7:35 ` Holger Schurig 0 siblings, 0 replies; 19+ messages in thread From: Holger Schurig @ 2016-01-13 7:35 UTC (permalink / raw) To: Lothar Waßmann Cc: Ian Campbell, Kumar Gala, Mark Rutland, Pawel Moll, Rob Herring, Russell King, Sascha Hauer, Shawn Guo, devicetree-u79uwXL29TY76Z2rM5mHXA, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, linux-kernel-u79uwXL29TY76Z2rM5mHXA Lothar Waßmann <LW-bxm8fMRDkQLDiMYJYoSAnRvVK+yQ3ZXh@public.gmane.org> writes: > +/ { > + model = "Ka-Ro electronics TX6S-8034 Module"; > + compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl"; > + timestamp = __DATE__, __TIME__; Is this needed or useful? There's a movement that aims to do "reproducible builds" ... being able to recompile an image and verify it against the supplied can be helpful for security audit purposes. > + display: display@di0 { > + compatible = "fsl,imx-parallel-display"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_disp0_1>; > + interface-pix-fmt = "rgb24"; > +// fsl,panel = <&lcd0_panel>; Probably not for upstream inclusion? -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH 1/3] ARM: dts: imx6: add support for Ka-Ro electronics TX6S-8034 module 2016-01-13 7:35 ` Holger Schurig @ 2016-01-13 11:10 ` Lothar Waßmann -1 siblings, 0 replies; 19+ messages in thread From: Lothar Waßmann @ 2016-01-13 11:10 UTC (permalink / raw) To: linux-arm-kernel Hi, > Lothar Wa?mann <LW@KARO-electronics.de> writes: > > > +/ { > > + model = "Ka-Ro electronics TX6S-8034 Module"; > > + compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl"; > > + timestamp = __DATE__, __TIME__; > > Is this needed or useful? > > There's a movement that aims to do "reproducible builds" ... being > able to recompile an image and verify it against the supplied can be > helpful for security audit purposes. > Ooops. I was on the wrong branch when creating these patches. Will resend this patch series soon. > > + display: display at di0 { > > + compatible = "fsl,imx-parallel-display"; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_disp0_1>; > > + interface-pix-fmt = "rgb24"; > > +// fsl,panel = <&lcd0_panel>; > > Probably not for upstream inclusion? > see above. ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH 1/3] ARM: dts: imx6: add support for Ka-Ro electronics TX6S-8034 module @ 2016-01-13 11:10 ` Lothar Waßmann 0 siblings, 0 replies; 19+ messages in thread From: Lothar Waßmann @ 2016-01-13 11:10 UTC (permalink / raw) To: Holger Schurig Cc: Ian Campbell, Kumar Gala, Mark Rutland, Pawel Moll, Rob Herring, Russell King, Sascha Hauer, Shawn Guo, devicetree, linux-arm-kernel, linux-kernel Hi, > Lothar Waßmann <LW@KARO-electronics.de> writes: > > > +/ { > > + model = "Ka-Ro electronics TX6S-8034 Module"; > > + compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl"; > > + timestamp = __DATE__, __TIME__; > > Is this needed or useful? > > There's a movement that aims to do "reproducible builds" ... being > able to recompile an image and verify it against the supplied can be > helpful for security audit purposes. > Ooops. I was on the wrong branch when creating these patches. Will resend this patch series soon. > > + display: display@di0 { > > + compatible = "fsl,imx-parallel-display"; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_disp0_1>; > > + interface-pix-fmt = "rgb24"; > > +// fsl,panel = <&lcd0_panel>; > > Probably not for upstream inclusion? > see above. ^ permalink raw reply [flat|nested] 19+ messages in thread
end of thread, other threads:[~2016-01-13 11:36 UTC | newest] Thread overview: 19+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2016-01-12 18:01 [PATCH 0/3] ARM: dts: imx6: add support for more i.MX6 modules from Ka-Ro electronics Lothar Waßmann 2016-01-12 18:01 ` Lothar Waßmann 2016-01-12 18:01 ` [PATCH 1/3] ARM: dts: imx6: add support for Ka-Ro electronics TX6S-8034 module Lothar Waßmann 2016-01-12 18:01 ` Lothar Waßmann 2016-01-12 18:01 ` [PATCH 2/3] ARM: dts: imx6ul: add support for Ka-Ro electronics TXUL modules Lothar Waßmann 2016-01-12 18:01 ` Lothar Waßmann 2016-01-12 18:01 ` [PATCH 3/3] ARM: dts: imx6: add display timing for NL12880BC20 display to Ka-Ro electronics TX6 LVDS modules Lothar Waßmann 2016-01-12 18:01 ` Lothar Waßmann 2016-01-12 18:43 ` [PATCH 2/3] ARM: dts: imx6ul: add support for Ka-Ro electronics TXUL modules Fabio Estevam 2016-01-12 18:43 ` Fabio Estevam 2016-01-12 18:43 ` Fabio Estevam 2016-01-13 11:36 ` Lothar Waßmann 2016-01-13 11:36 ` Lothar Waßmann 2016-01-13 11:36 ` Lothar Waßmann 2016-01-13 7:35 ` [PATCH 1/3] ARM: dts: imx6: add support for Ka-Ro electronics TX6S-8034 module Holger Schurig 2016-01-13 7:35 ` Holger Schurig 2016-01-13 7:35 ` Holger Schurig 2016-01-13 11:10 ` Lothar Waßmann 2016-01-13 11:10 ` Lothar Waßmann
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.