From: "Pandiyan, Dhinakaran" <dhinakaran.pandiyan@intel.com>
To: "Vivi, Rodrigo" <rodrigo.vivi@intel.com>
Cc: "Nikula, Jani" <jani.nikula@intel.com>,
"intel-gfx@lists.freedesktop.org"
<intel-gfx@lists.freedesktop.org>
Subject: Re: [PATCH 4/6] drm/i915/cnp: Backlight support for CNP.
Date: Thu, 1 Jun 2017 22:43:55 +0000 [thread overview]
Message-ID: <1496358266.24196.41.camel@dk-H97M-D3H> (raw)
In-Reply-To: <1496356392-13668-4-git-send-email-rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
-DK
On Thu, 2017-06-01 at 15:33 -0700, Rodrigo Vivi wrote:
> Split out BXT and CNP's setup_backlight(),enable_backlight(),
> disable_backlight() and hz_to_pwm() into
> two separate functions instead of reusing BXT function.
>
> Reuse set_backlight() and get_backlight() since they have
> no reference to the utility pin.
>
> v2: Reuse BXT functions with controller 0 instead of
> redefining it. (Jani).
> Use dev_priv->rawclk_freq instead of getting the value
> from SFUSE_STRAP.
> v3: Avoid setup backligh controller along with hooks and
> fully reuse hooks setup as suggested by Jani.
> v4: Clean up commit message.
> v5: Implement per PCH instead per platform.
>
> v6: Introduce a new function for CNP.(Jani and Ville)
>
> v7: Squash the all CNP Backlight support patches into a
> single patch. (Jani)
>
> v8: Correct indentation, remove unneeded blank lines and
> correct mail address (Jani).
>
> v9: Remove unused enum pipe. (by CI)
>
> v10: Remove comment mentioning SFUSE_STRAP in a part of
> the code that we don't use it. (Jani)
> Make controller = 0 since current CNP has only one
> controller and put a comment mentioning why we
> reuse the BXT definitions and are keeping the
> controller = 0. (DK)
> v11: Remove spurious line. (DK)
>
> Reviewed-by: Jani Nikula <jani.nikula@intel.com>
> Suggested-by: Jani Nikula <jani.nikula@intel.com>
> Suggested-by: Ville Syrjala <ville.syrjala@intel.com>
> Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
> Cc: Jani Nikula <jani.nikula@intel.com>
> Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
> ---
> drivers/gpu/drm/i915/intel_panel.c | 96 ++++++++++++++++++++++++++++++++++++++
> 1 file changed, 96 insertions(+)
>
> diff --git a/drivers/gpu/drm/i915/intel_panel.c b/drivers/gpu/drm/i915/intel_panel.c
> index c8103f8..4114cb3 100644
> --- a/drivers/gpu/drm/i915/intel_panel.c
> +++ b/drivers/gpu/drm/i915/intel_panel.c
> @@ -796,6 +796,19 @@ static void bxt_disable_backlight(struct intel_connector *connector)
> }
> }
>
> +static void cnp_disable_backlight(struct intel_connector *connector)
> +{
> + struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
> + struct intel_panel *panel = &connector->panel;
> + u32 tmp;
> +
> + intel_panel_actually_set_backlight(connector, 0);
> +
> + tmp = I915_READ(BXT_BLC_PWM_CTL(panel->backlight.controller));
> + I915_WRITE(BXT_BLC_PWM_CTL(panel->backlight.controller),
> + tmp & ~BXT_BLC_PWM_ENABLE);
> +}
> +
> static void pwm_disable_backlight(struct intel_connector *connector)
> {
> struct intel_panel *panel = &connector->panel;
> @@ -1086,6 +1099,35 @@ static void bxt_enable_backlight(struct intel_connector *connector)
> pwm_ctl | BXT_BLC_PWM_ENABLE);
> }
>
> +static void cnp_enable_backlight(struct intel_connector *connector)
> +{
> + struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
> + struct intel_panel *panel = &connector->panel;
> + u32 pwm_ctl;
> +
> + pwm_ctl = I915_READ(BXT_BLC_PWM_CTL(panel->backlight.controller));
> + if (pwm_ctl & BXT_BLC_PWM_ENABLE) {
> + DRM_DEBUG_KMS("backlight already enabled\n");
> + pwm_ctl &= ~BXT_BLC_PWM_ENABLE;
> + I915_WRITE(BXT_BLC_PWM_CTL(panel->backlight.controller),
> + pwm_ctl);
> + }
> +
> + I915_WRITE(BXT_BLC_PWM_FREQ(panel->backlight.controller),
> + panel->backlight.max);
> +
> + intel_panel_actually_set_backlight(connector, panel->backlight.level);
> +
> + pwm_ctl = 0;
> + if (panel->backlight.active_low_pwm)
> + pwm_ctl |= BXT_BLC_PWM_POLARITY;
> +
> + I915_WRITE(BXT_BLC_PWM_CTL(panel->backlight.controller), pwm_ctl);
> + POSTING_READ(BXT_BLC_PWM_CTL(panel->backlight.controller));
> + I915_WRITE(BXT_BLC_PWM_CTL(panel->backlight.controller),
> + pwm_ctl | BXT_BLC_PWM_ENABLE);
> +}
> +
> static void pwm_enable_backlight(struct intel_connector *connector)
> {
> struct intel_panel *panel = &connector->panel;
> @@ -1250,6 +1292,17 @@ void intel_backlight_device_unregister(struct intel_connector *connector)
> #endif /* CONFIG_BACKLIGHT_CLASS_DEVICE */
>
> /*
> + * CNP: PWM clock frequency is 19.2 MHz or 24 MHz.
> + * PWM increment = 1
> + */
> +static u32 cnp_hz_to_pwm(struct intel_connector *connector, u32 pwm_freq_hz)
> +{
> + struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
> +
> + return DIV_ROUND_CLOSEST(KHz(dev_priv->rawclk_freq), pwm_freq_hz);
> +}
> +
> +/*
> * BXT: PWM clock frequency = 19.2 MHz.
> */
> static u32 bxt_hz_to_pwm(struct intel_connector *connector, u32 pwm_freq_hz)
> @@ -1644,6 +1697,42 @@ static int vlv_setup_backlight(struct intel_connector *connector, enum pipe pipe
> return 0;
> }
>
> +static int
> +cnp_setup_backlight(struct intel_connector *connector, enum pipe unused)
> +{
> + struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
> + struct intel_panel *panel = &connector->panel;
> + u32 pwm_ctl, val;
> +
> + /*
> + * CNP has the BXT implementation of backlight, but with only
> + * one controller. Future platforms could have multiple controllers
> + * so let's make this extensible and prepared for the future.
> + */
> + panel->backlight.controller = 0;
> +
> + pwm_ctl = I915_READ(BXT_BLC_PWM_CTL(panel->backlight.controller));
> +
> + panel->backlight.active_low_pwm = pwm_ctl & BXT_BLC_PWM_POLARITY;
> + panel->backlight.max =
> + I915_READ(BXT_BLC_PWM_FREQ(panel->backlight.controller));
> +
> + if (!panel->backlight.max)
> + panel->backlight.max = get_backlight_max_vbt(connector);
> +
> + if (!panel->backlight.max)
> + return -ENODEV;
> +
> + val = bxt_get_backlight(connector);
> + val = intel_panel_compute_brightness(connector, val);
> + panel->backlight.level = clamp(val, panel->backlight.min,
> + panel->backlight.max);
> +
> + panel->backlight.enabled = pwm_ctl & BXT_BLC_PWM_ENABLE;
> +
> + return 0;
> +}
> +
> static int pwm_setup_backlight(struct intel_connector *connector,
> enum pipe pipe)
> {
> @@ -1760,6 +1849,13 @@ void intel_panel_destroy_backlight(struct drm_connector *connector)
> panel->backlight.set = bxt_set_backlight;
> panel->backlight.get = bxt_get_backlight;
> panel->backlight.hz_to_pwm = bxt_hz_to_pwm;
> + } else if (HAS_PCH_CNP(dev_priv)) {
> + panel->backlight.setup = cnp_setup_backlight;
> + panel->backlight.enable = cnp_enable_backlight;
> + panel->backlight.disable = cnp_disable_backlight;
> + panel->backlight.set = bxt_set_backlight;
> + panel->backlight.get = bxt_get_backlight;
> + panel->backlight.hz_to_pwm = cnp_hz_to_pwm;
> } else if (HAS_PCH_LPT(dev_priv) || HAS_PCH_SPT(dev_priv) ||
> HAS_PCH_KBP(dev_priv)) {
> panel->backlight.setup = lpt_setup_backlight;
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
next prev parent reply other threads:[~2017-06-01 22:43 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-06-01 22:33 [PATCH 1/6] drm/i915/cnp: Introduce Cannonpoint PCH Rodrigo Vivi
2017-06-01 22:33 ` [PATCH 2/6] drm/i915/cnp: Add PCI ID for Cannonpoint LP PCH Rodrigo Vivi
2017-06-01 22:33 ` [PATCH 3/6] drm/i915/cnp: Get/set proper Raw clock frequency on CNP Rodrigo Vivi
2017-06-01 22:33 ` [PATCH 4/6] drm/i915/cnp: Backlight support for CNP Rodrigo Vivi
2017-06-01 22:43 ` Pandiyan, Dhinakaran [this message]
2017-06-01 22:33 ` [PATCH 5/6] drm/i915/cnp: add CNP gmbus support Rodrigo Vivi
2017-06-01 22:33 ` [PATCH 6/6] drm/i915/cnp: Panel Power sequence changes for CNP PCH Rodrigo Vivi
2017-06-01 22:50 ` ✗ Fi.CI.BAT: failure for series starting with [1/6] drm/i915/cnp: Introduce Cannonpoint PCH Patchwork
2017-06-01 23:05 ` Vivi, Rodrigo
2017-06-02 6:17 ` Saarinen, Jani
2017-06-02 17:43 ` Rodrigo Vivi
-- strict thread matches above, loose matches on Subject: below --
2017-06-02 20:06 [PATCH 1/6] " Rodrigo Vivi
2017-06-02 20:06 ` [PATCH 4/6] drm/i915/cnp: Backlight support for CNP Rodrigo Vivi
2017-06-01 0:23 [PATCH 1/6] drm/i915/cnp: Introduce Cannonpoint PCH Rodrigo Vivi
2017-06-01 0:23 ` [PATCH 4/6] drm/i915/cnp: Backlight support for CNP Rodrigo Vivi
2017-06-01 14:01 ` Jani Nikula
2017-05-30 22:11 [PATCH 1/6] drm/i915/cnp: Introduce Cannonpoint PCH Rodrigo Vivi
2017-05-30 22:11 ` [PATCH 4/6] drm/i915/cnp: Backlight support for CNP Rodrigo Vivi
2017-05-30 21:53 [PATCH 1/6] drm/i915/cnp: Introduce Cannonpoint PCH Rodrigo Vivi
2017-05-30 21:53 ` [PATCH 4/6] drm/i915/cnp: Backlight support for CNP Rodrigo Vivi
2017-05-31 5:57 ` kbuild test robot
2017-05-09 19:16 [PATCH 0/6] Cannonpoint Enabling Patches Anusha Srivatsa
2017-05-09 19:16 ` [PATCH 4/6] drm/i915/cnp: Backlight support for CNP Anusha Srivatsa
2017-05-08 23:44 [PATCH 0/6] Cannonpoint Enabling Patches Anusha Srivatsa
2017-05-08 23:45 ` [PATCH 4/6] drm/i915/cnp: Backlight support for CNP Anusha Srivatsa
2017-05-09 0:10 ` Pandiyan, Dhinakaran
2017-05-09 0:11 ` Srivatsa, Anusha
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1496358266.24196.41.camel@dk-H97M-D3H \
--to=dhinakaran.pandiyan@intel.com \
--cc=intel-gfx@lists.freedesktop.org \
--cc=jani.nikula@intel.com \
--cc=rodrigo.vivi@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox