Intel-GFX Archive on lore.kernel.org
 help / color / mirror / Atom feed
From: "Pandiyan, Dhinakaran" <dhinakaran.pandiyan@intel.com>
To: "Srivatsa, Anusha" <anusha.srivatsa@intel.com>
Cc: "Nikula, Jani" <jani.nikula@intel.com>,
	"intel-gfx@lists.freedesktop.org"
	<intel-gfx@lists.freedesktop.org>,
	"Vivi, Rodrigo" <rodrigo.vivi@intel.com>
Subject: Re: [PATCH 4/6] drm/i915/cnp: Backlight support for CNP.
Date: Tue, 9 May 2017 00:10:09 +0000	[thread overview]
Message-ID: <1494289800.26187.63.camel@dk-H97M-D3H> (raw)
In-Reply-To: <1494287104-13109-5-git-send-email-anusha.srivatsa@intel.com>

On Mon, 2017-05-08 at 16:45 -0700, Anusha Srivatsa wrote:
> From: Rodrigo Vivi <rodrigo.vivi@intel.com>
> 
> Split out BXT and CNP's setup_backlight(),enable_backlight(),
> disable_backlight() and hz_to_pwm() into
> two separate functions instead of reusing BXT function.
> 
> Reuse set_backlight() and get_backlight() since they have
> no reference to the utility pin.
> 
> v2: Reuse BXT functions with controller 0 instead of
>     redefining it. (Jani).
>     Use dev_priv->rawclk_freq instead of getting the value
>     from SFUSE_STRAP.
> v3: Avoid setup backligh controller along with hooks and
>     fully reuse hooks setup as suggested by Jani.
> v4: Clean up commit message.
> v5: Implement per PCH instead per platform.
> 
> v6: Introduce a new function for CNP.(Jani and Ville)
> 
> v7: Squash the all CNP Backlight support patches into a
> single patch. (Jani)
> 
> v8: Correct indentation, remove unneeded blank lines and
> correct mail address (Jani).
> 
> Reviewed-by: Jani Nikula <jani.nikula@intel.com>
> Suggested-by: Jani Nikula <jani.nikula@intel.com>
> Suggested-by: Ville Syrjala <ville.syrjala@intel.com>
> Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
> Cc: Jani Nikula <jani.nikula@intel.com>
> Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
> ---
>  drivers/gpu/drm/i915/intel_panel.c | 94 ++++++++++++++++++++++++++++++++++++++
>  1 file changed, 94 insertions(+)
> 
> diff --git a/drivers/gpu/drm/i915/intel_panel.c b/drivers/gpu/drm/i915/intel_panel.c
> index cb50c52..22da1e2 100644
> --- a/drivers/gpu/drm/i915/intel_panel.c
> +++ b/drivers/gpu/drm/i915/intel_panel.c
> @@ -796,6 +796,19 @@ static void bxt_disable_backlight(struct intel_connector *connector)
>  	}
>  }
>  
> +static void cnp_disable_backlight(struct intel_connector *connector)
> +{
> +	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
> +	struct intel_panel *panel = &connector->panel;
> +	u32 tmp;
> +
> +	intel_panel_actually_set_backlight(connector, 0);
> +
> +	tmp = I915_READ(BXT_BLC_PWM_CTL(panel->backlight.controller));
> +	I915_WRITE(BXT_BLC_PWM_CTL(panel->backlight.controller),
> +		   tmp & ~BXT_BLC_PWM_ENABLE);
> +}
> +
>  static void pwm_disable_backlight(struct intel_connector *connector)
>  {
>  	struct intel_panel *panel = &connector->panel;
> @@ -1076,6 +1089,36 @@ static void bxt_enable_backlight(struct intel_connector *connector)
>  			pwm_ctl | BXT_BLC_PWM_ENABLE);
>  }
>  
> +static void cnp_enable_backlight(struct intel_connector *connector)
> +{
> +	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
> +	struct intel_panel *panel = &connector->panel;
> +	enum pipe pipe = intel_get_pipe_from_connector(connector);
> +	u32 pwm_ctl;
> +
> +	pwm_ctl = I915_READ(BXT_BLC_PWM_CTL(panel->backlight.controller));
> +	if (pwm_ctl & BXT_BLC_PWM_ENABLE) {
> +		DRM_DEBUG_KMS("backlight already enabled\n");
> +		pwm_ctl &= ~BXT_BLC_PWM_ENABLE;
> +		I915_WRITE(BXT_BLC_PWM_CTL(panel->backlight.controller),
> +			   pwm_ctl);
> +	}
> +
> +	I915_WRITE(BXT_BLC_PWM_FREQ(panel->backlight.controller),
> +		   panel->backlight.max);
> +
> +	intel_panel_actually_set_backlight(connector, panel->backlight.level);
> +
> +	pwm_ctl = 0;
> +	if (panel->backlight.active_low_pwm)
> +		pwm_ctl |= BXT_BLC_PWM_POLARITY;
> +
> +	I915_WRITE(BXT_BLC_PWM_CTL(panel->backlight.controller), pwm_ctl);
> +	POSTING_READ(BXT_BLC_PWM_CTL(panel->backlight.controller));
> +	I915_WRITE(BXT_BLC_PWM_CTL(panel->backlight.controller),
> +		   pwm_ctl | BXT_BLC_PWM_ENABLE);
> +}
> +
>  static void pwm_enable_backlight(struct intel_connector *connector)
>  {
>  	struct intel_panel *panel = &connector->panel;
> @@ -1239,6 +1282,18 @@ void intel_backlight_device_unregister(struct intel_connector *connector)
>  #endif /* CONFIG_BACKLIGHT_CLASS_DEVICE */
>  
>  /*
> + * CNP: PWM clock frequency is 19.2 MHz or 24 MHz.
> + *      Value is found in SFUSE_STRAP.
> + *      PWM increment = 1
> + */
> +static u32 cnp_hz_to_pwm(struct intel_connector *connector, u32 pwm_freq_hz)
> +{
> +	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
> +
> +	return DIV_ROUND_CLOSEST(KHz(dev_priv->rawclk_freq), pwm_freq_hz);
> +}
> +
> +/*
>   * BXT: PWM clock frequency = 19.2 MHz.
>   */
>  static u32 bxt_hz_to_pwm(struct intel_connector *connector, u32 pwm_freq_hz)
> @@ -1633,6 +1688,37 @@ bxt_setup_backlight(struct intel_connector *connector, enum pipe unused)
>  	return 0;
>  }
>  
> +static int
> +cnp_setup_backlight(struct intel_connector *connector, enum pipe unused)
> +{
> +	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
> +	struct intel_panel *panel = &connector->panel;
> +	u32 pwm_ctl, val;
> +
> +	panel->backlight.controller = dev_priv->vbt.backlight.controller;
> +
> +	pwm_ctl = I915_READ(BXT_BLC_PWM_CTL(panel->backlight.controller));
> +
> +	panel->backlight.active_low_pwm = pwm_ctl & BXT_BLC_PWM_POLARITY;
> +	panel->backlight.max =
> +		I915_READ(BXT_BLC_PWM_FREQ(panel->backlight.controller));
> +
> +	if (!panel->backlight.max)
> +		panel->backlight.max = get_backlight_max_vbt(connector);
> +
> +	if (!panel->backlight.max)
> +		return -ENODEV;
> +
> +	val = bxt_get_backlight(connector);
> +	val = intel_panel_compute_brightness(connector, val);
> +	panel->backlight.level = clamp(val, panel->backlight.min,
> +				       panel->backlight.max);
> +
> +	panel->backlight.enabled = pwm_ctl & BXT_BLC_PWM_ENABLE;
> +
> +	return 0;
> +}
> +
>  static int pwm_setup_backlight(struct intel_connector *connector,
>  			       enum pipe pipe)
>  {
> @@ -1749,6 +1835,14 @@ intel_panel_init_backlight_funcs(struct intel_panel *panel)
>  		panel->backlight.set = bxt_set_backlight;
>  		panel->backlight.get = bxt_get_backlight;
>  		panel->backlight.hz_to_pwm = bxt_hz_to_pwm;
> +		panel->backlight.hz_to_pwm = bxt_hz_to_pwm;

This diff should not be here.

-DK


> +	} else if (HAS_PCH_CNP(dev_priv)) {
> +		panel->backlight.setup = cnp_setup_backlight;
> +		panel->backlight.enable = cnp_enable_backlight;
> +		panel->backlight.disable = cnp_disable_backlight;
> +		panel->backlight.set = bxt_set_backlight;
> +		panel->backlight.get = bxt_get_backlight;
> +		panel->backlight.hz_to_pwm = cnp_hz_to_pwm;
>  	} else if (HAS_PCH_LPT(dev_priv) || HAS_PCH_SPT(dev_priv) ||
>  		   HAS_PCH_KBP(dev_priv)) {
>  		panel->backlight.setup = lpt_setup_backlight;

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

  reply	other threads:[~2017-05-09  0:10 UTC|newest]

Thread overview: 19+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2017-05-08 23:44 [PATCH 0/6] Cannonpoint Enabling Patches Anusha Srivatsa
2017-05-08 23:44 ` [PATCH 1/6] drm/i915/cnp: Introduce Cannonpoint PCH Anusha Srivatsa
2017-05-08 23:45 ` [PATCH 2/6] drm/i915/cnp: Add PCI ID for Cannonpoint LP PCH Anusha Srivatsa
2017-05-08 23:45 ` [PATCH 3/6] drm/i915/cnp: Get/set proper Raw clock frequency on CNP Anusha Srivatsa
2017-05-08 23:45 ` [PATCH 4/6] drm/i915/cnp: Backlight support for CNP Anusha Srivatsa
2017-05-09  0:10   ` Pandiyan, Dhinakaran [this message]
2017-05-09  0:11     ` Srivatsa, Anusha
2017-05-08 23:45 ` [PATCH 5/6] drm/i915/cnp: add CNP gmbus support Anusha Srivatsa
2017-05-08 23:45 ` [PATCH 6/6] drm/i915/cnp: Panel Power sequence changes for CNP PCH Anusha Srivatsa
2017-05-09  6:46 ` ✗ Fi.CI.BAT: failure for Cannonpoint Enabling Patches Patchwork
  -- strict thread matches above, loose matches on Subject: below --
2017-05-09 19:16 [PATCH 0/6] " Anusha Srivatsa
2017-05-09 19:16 ` [PATCH 4/6] drm/i915/cnp: Backlight support for CNP Anusha Srivatsa
2017-05-30 21:53 [PATCH 1/6] drm/i915/cnp: Introduce Cannonpoint PCH Rodrigo Vivi
2017-05-30 21:53 ` [PATCH 4/6] drm/i915/cnp: Backlight support for CNP Rodrigo Vivi
2017-05-31  5:57   ` kbuild test robot
2017-05-30 22:11 [PATCH 1/6] drm/i915/cnp: Introduce Cannonpoint PCH Rodrigo Vivi
2017-05-30 22:11 ` [PATCH 4/6] drm/i915/cnp: Backlight support for CNP Rodrigo Vivi
2017-06-01  0:23 [PATCH 1/6] drm/i915/cnp: Introduce Cannonpoint PCH Rodrigo Vivi
2017-06-01  0:23 ` [PATCH 4/6] drm/i915/cnp: Backlight support for CNP Rodrigo Vivi
2017-06-01 14:01   ` Jani Nikula
2017-06-01 22:33 [PATCH 1/6] drm/i915/cnp: Introduce Cannonpoint PCH Rodrigo Vivi
2017-06-01 22:33 ` [PATCH 4/6] drm/i915/cnp: Backlight support for CNP Rodrigo Vivi
2017-06-01 22:43   ` Pandiyan, Dhinakaran
2017-06-02 20:06 [PATCH 1/6] drm/i915/cnp: Introduce Cannonpoint PCH Rodrigo Vivi
2017-06-02 20:06 ` [PATCH 4/6] drm/i915/cnp: Backlight support for CNP Rodrigo Vivi

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1494289800.26187.63.camel@dk-H97M-D3H \
    --to=dhinakaran.pandiyan@intel.com \
    --cc=anusha.srivatsa@intel.com \
    --cc=intel-gfx@lists.freedesktop.org \
    --cc=jani.nikula@intel.com \
    --cc=rodrigo.vivi@intel.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox