* [PATCH 0/2] Add Phytec phyFLEX-i.MX6 board @ 2013-05-29 21:06 Christian Hemp 2013-05-29 21:06 ` [PATCH 1/2] ARM: dts: imx6q: Add pinctrl for usdhc2 and enet Christian Hemp 2013-05-29 21:06 ` [PATCH 2/2] ARM: dts: Phytec phyFLEX-i.MX6 support Christian Hemp 0 siblings, 2 replies; 6+ messages in thread From: Christian Hemp @ 2013-05-29 21:06 UTC (permalink / raw) To: linux-arm-kernel This patchset adds basic support for Phytec's phyFLEX-i.MX6. It's based on git repo from Shwan Guo branche imx/dt Christian Hemp (2): ARM: dts: imx6q: Add pinctrl for usdhc2 and enet ARM: dts: Phytec phyFLEX-i.MX6 support arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx6q-phytec-phyflex.dts | 76 ++++++++++++++++++++++++++++ arch/arm/boot/dts/imx6q.dtsi | 33 ++++++++++++ 3 files changed, 110 insertions(+) create mode 100644 arch/arm/boot/dts/imx6q-phytec-phyflex.dts -- 1.7.9.5 ^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH 1/2] ARM: dts: imx6q: Add pinctrl for usdhc2 and enet 2013-05-29 21:06 [PATCH 0/2] Add Phytec phyFLEX-i.MX6 board Christian Hemp @ 2013-05-29 21:06 ` Christian Hemp 2013-05-30 6:25 ` Shawn Guo 2013-05-29 21:06 ` [PATCH 2/2] ARM: dts: Phytec phyFLEX-i.MX6 support Christian Hemp 1 sibling, 1 reply; 6+ messages in thread From: Christian Hemp @ 2013-05-29 21:06 UTC (permalink / raw) To: linux-arm-kernel Add a group to the usdhc2 and enet pinctrl. Signed-off-by: Christian Hemp <c.hemp@phytec.de> --- arch/arm/boot/dts/imx6q.dtsi | 33 +++++++++++++++++++++++++++++++++ 1 file changed, 33 insertions(+) diff --git a/arch/arm/boot/dts/imx6q.dtsi b/arch/arm/boot/dts/imx6q.dtsi index ed11bcf..c0c8b7b 100644 --- a/arch/arm/boot/dts/imx6q.dtsi +++ b/arch/arm/boot/dts/imx6q.dtsi @@ -157,6 +157,28 @@ MX6Q_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 >; }; + + pinctrl_enet_3: enetgrp-3 { + fsl,pins = < + MX6Q_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 + MX6Q_PAD_ENET_MDC__ENET_MDC 0x1b0b0 + MX6Q_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0 + MX6Q_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0 + MX6Q_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0 + MX6Q_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0 + MX6Q_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0 + MX6Q_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0 + MX6Q_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 + MX6Q_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 + MX6Q_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 + MX6Q_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 + MX6Q_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 + MX6Q_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 + MX6Q_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 + MX6Q_PAD_ENET_CRS_DV__SPDIF_EXT_CLK 0x1b0b0 + MX6Q_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0 + >; + }; }; gpmi-nand { @@ -266,6 +288,17 @@ MX6Q_PAD_NANDF_D7__SD2_DATA7 0x17059 >; }; + + pinctrl_usdhc2_2: usdhc2grp-2 { + fsl,pins = < + MX6Q_PAD_SD2_CMD__SD2_CMD 0x17059 + MX6Q_PAD_SD2_CLK__SD2_CLK 0x10059 + MX6Q_PAD_SD2_DAT0__SD2_DATA0 0x17059 + MX6Q_PAD_SD2_DAT1__SD2_DATA1 0x17059 + MX6Q_PAD_SD2_DAT2__SD2_DATA2 0x17059 + MX6Q_PAD_SD2_DAT3__SD2_DATA3 0x17059 + >; + }; }; usdhc3 { -- 1.7.9.5 ^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH 1/2] ARM: dts: imx6q: Add pinctrl for usdhc2 and enet 2013-05-29 21:06 ` [PATCH 1/2] ARM: dts: imx6q: Add pinctrl for usdhc2 and enet Christian Hemp @ 2013-05-30 6:25 ` Shawn Guo 0 siblings, 0 replies; 6+ messages in thread From: Shawn Guo @ 2013-05-30 6:25 UTC (permalink / raw) To: linux-arm-kernel On Wed, May 29, 2013 at 11:06:48PM +0200, Christian Hemp wrote: > Add a group to the usdhc2 and enet pinctrl. > > Signed-off-by: Christian Hemp <c.hemp@phytec.de> > --- > arch/arm/boot/dts/imx6q.dtsi | 33 +++++++++++++++++++++++++++++++++ > 1 file changed, 33 insertions(+) > > diff --git a/arch/arm/boot/dts/imx6q.dtsi b/arch/arm/boot/dts/imx6q.dtsi > index ed11bcf..c0c8b7b 100644 > --- a/arch/arm/boot/dts/imx6q.dtsi > +++ b/arch/arm/boot/dts/imx6q.dtsi > @@ -157,6 +157,28 @@ > MX6Q_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 > >; > }; > + > + pinctrl_enet_3: enetgrp-3 { > + fsl,pins = < > + MX6Q_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 > + MX6Q_PAD_ENET_MDC__ENET_MDC 0x1b0b0 > + MX6Q_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0 > + MX6Q_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0 > + MX6Q_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0 > + MX6Q_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0 > + MX6Q_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0 > + MX6Q_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0 > + MX6Q_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 > + MX6Q_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 > + MX6Q_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 > + MX6Q_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 > + MX6Q_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 > + MX6Q_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 > + MX6Q_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 > + MX6Q_PAD_ENET_CRS_DV__SPDIF_EXT_CLK 0x1b0b0 Why do you need to set up SPDIF_EXT_CLK in ENET pin group? Shawn > + MX6Q_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0 > + >; > + }; > }; > > gpmi-nand { > @@ -266,6 +288,17 @@ > MX6Q_PAD_NANDF_D7__SD2_DATA7 0x17059 > >; > }; > + > + pinctrl_usdhc2_2: usdhc2grp-2 { > + fsl,pins = < > + MX6Q_PAD_SD2_CMD__SD2_CMD 0x17059 > + MX6Q_PAD_SD2_CLK__SD2_CLK 0x10059 > + MX6Q_PAD_SD2_DAT0__SD2_DATA0 0x17059 > + MX6Q_PAD_SD2_DAT1__SD2_DATA1 0x17059 > + MX6Q_PAD_SD2_DAT2__SD2_DATA2 0x17059 > + MX6Q_PAD_SD2_DAT3__SD2_DATA3 0x17059 > + >; > + }; > }; > > usdhc3 { > -- > 1.7.9.5 > ^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH 2/2] ARM: dts: Phytec phyFLEX-i.MX6 support 2013-05-29 21:06 [PATCH 0/2] Add Phytec phyFLEX-i.MX6 board Christian Hemp 2013-05-29 21:06 ` [PATCH 1/2] ARM: dts: imx6q: Add pinctrl for usdhc2 and enet Christian Hemp @ 2013-05-29 21:06 ` Christian Hemp 2013-05-30 6:31 ` Shawn Guo 1 sibling, 1 reply; 6+ messages in thread From: Christian Hemp @ 2013-05-29 21:06 UTC (permalink / raw) To: linux-arm-kernel Add support for Phytec phyFLEX-i.MX6 board Signed-off-by: Christian Hemp <c.hemp@phytec.de> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx6q-phytec-phyflex.dts | 76 ++++++++++++++++++++++++++++ 2 files changed, 77 insertions(+) create mode 100644 arch/arm/boot/dts/imx6q-phytec-phyflex.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 4c58951..6ffdaa1 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -118,6 +118,7 @@ dtb-$(CONFIG_ARCH_MXC) += \ imx6dl-sabresd.dtb \ imx6dl-wandboard.dtb \ imx6q-arm2.dtb \ + imx6q-phytec-phyflex.dtb \ imx6q-sabreauto.dtb \ imx6q-sabrelite.dtb \ imx6q-sabresd.dtb \ diff --git a/arch/arm/boot/dts/imx6q-phytec-phyflex.dts b/arch/arm/boot/dts/imx6q-phytec-phyflex.dts new file mode 100644 index 0000000..9690691 --- /dev/null +++ b/arch/arm/boot/dts/imx6q-phytec-phyflex.dts @@ -0,0 +1,76 @@ +/* + * Copyright 2013 Christian Hemp, Phytec Messtechnik GmbH + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +#include "imx6q.dtsi" + +/ { + model = "Phytec phyFLEX-i.MX6"; + compatible = "phytec,phyflex-imx6", "fsl,imx6q"; + + memory { + reg = <0x10000000 0x80000000>; + }; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + hog { + pinctrl_hog: hoggrp { + fsl,pins = < + MX6Q_PAD_EIM_D23__GPIO3_IO23 0x80000000 + >; + }; + }; + + phyflex { + pinctrl_usdhc3_phyflex: usdhc3grp-phyflex { + fsl,pins = < + MX6Q_PAD_ENET_RXD0__GPIO1_IO27 0x80000000 + MX6Q_PAD_ENET_TXD1__GPIO1_IO29 0x80000000 + >; + }; + }; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet_3>; + phy-mode = "rgmii"; + phy-reset-gpios = <&gpio3 23 0>; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4_1>; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc2_2>; + cd-gpios = <&gpio1 4 0>; + wp-gpios = <&gpio1 2 0>; + status = "okay"; +}; + +&usdhc3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc3_2 + &pinctrl_usdhc3_phyflex>; + cd-gpios = <&gpio1 27 0>; + wp-gpios = <&gpio1 29 0>; + status = "okay"; +}; + -- 1.7.9.5 ^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH 2/2] ARM: dts: Phytec phyFLEX-i.MX6 support 2013-05-29 21:06 ` [PATCH 2/2] ARM: dts: Phytec phyFLEX-i.MX6 support Christian Hemp @ 2013-05-30 6:31 ` Shawn Guo 2013-05-31 9:56 ` Christian Hemp 0 siblings, 1 reply; 6+ messages in thread From: Shawn Guo @ 2013-05-30 6:31 UTC (permalink / raw) To: linux-arm-kernel On Wed, May 29, 2013 at 11:06:49PM +0200, Christian Hemp wrote: > Add support for Phytec phyFLEX-i.MX6 board It's a board supporting all i.MX6 family? Can we name it using SoC than family name? > > Signed-off-by: Christian Hemp <c.hemp@phytec.de> > --- > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/imx6q-phytec-phyflex.dts | 76 ++++++++++++++++++++++++++++ > 2 files changed, 77 insertions(+) > create mode 100644 arch/arm/boot/dts/imx6q-phytec-phyflex.dts > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index 4c58951..6ffdaa1 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -118,6 +118,7 @@ dtb-$(CONFIG_ARCH_MXC) += \ > imx6dl-sabresd.dtb \ > imx6dl-wandboard.dtb \ > imx6q-arm2.dtb \ > + imx6q-phytec-phyflex.dtb \ > imx6q-sabreauto.dtb \ > imx6q-sabrelite.dtb \ > imx6q-sabresd.dtb \ > diff --git a/arch/arm/boot/dts/imx6q-phytec-phyflex.dts b/arch/arm/boot/dts/imx6q-phytec-phyflex.dts > new file mode 100644 > index 0000000..9690691 > --- /dev/null > +++ b/arch/arm/boot/dts/imx6q-phytec-phyflex.dts > @@ -0,0 +1,76 @@ > +/* > + * Copyright 2013 Christian Hemp, Phytec Messtechnik GmbH > + * > + * The code contained herein is licensed under the GNU General Public > + * License. You may obtain a copy of the GNU General Public License > + * Version 2 or later at the following locations: > + * > + * http://www.opensource.org/licenses/gpl-license.html > + * http://www.gnu.org/copyleft/gpl.html > + */ > + > +/dts-v1/; > +#include "imx6q.dtsi" > + > +/ { > + model = "Phytec phyFLEX-i.MX6"; > + compatible = "phytec,phyflex-imx6", "fsl,imx6q"; ditto Shawn > + > + memory { > + reg = <0x10000000 0x80000000>; > + }; > +}; > + > +&iomuxc { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_hog>; > + > + hog { > + pinctrl_hog: hoggrp { > + fsl,pins = < > + MX6Q_PAD_EIM_D23__GPIO3_IO23 0x80000000 > + >; > + }; > + }; > + > + phyflex { > + pinctrl_usdhc3_phyflex: usdhc3grp-phyflex { > + fsl,pins = < > + MX6Q_PAD_ENET_RXD0__GPIO1_IO27 0x80000000 > + MX6Q_PAD_ENET_TXD1__GPIO1_IO29 0x80000000 > + >; > + }; > + }; > +}; > + > +&fec { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_enet_3>; > + phy-mode = "rgmii"; > + phy-reset-gpios = <&gpio3 23 0>; > + status = "okay"; > +}; > + > +&uart4 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart4_1>; > + status = "okay"; > +}; > + > +&usdhc2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usdhc2_2>; > + cd-gpios = <&gpio1 4 0>; > + wp-gpios = <&gpio1 2 0>; > + status = "okay"; > +}; > + > +&usdhc3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usdhc3_2 > + &pinctrl_usdhc3_phyflex>; > + cd-gpios = <&gpio1 27 0>; > + wp-gpios = <&gpio1 29 0>; > + status = "okay"; > +}; > + > -- > 1.7.9.5 > ^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH 2/2] ARM: dts: Phytec phyFLEX-i.MX6 support 2013-05-30 6:31 ` Shawn Guo @ 2013-05-31 9:56 ` Christian Hemp 0 siblings, 0 replies; 6+ messages in thread From: Christian Hemp @ 2013-05-31 9:56 UTC (permalink / raw) To: linux-arm-kernel Hello Shawn, Am Donnerstag, den 30.05.2013, 14:31 +0800 schrieb Shawn Guo: > On Wed, May 29, 2013 at 11:06:49PM +0200, Christian Hemp wrote: > > Add support for Phytec phyFLEX-i.MX6 board > > It's a board supporting all i.MX6 family? At the moment only i.MX6q but this will change. > Can we name it using SoC than > family name? Okay. Christian > > > > Signed-off-by: Christian Hemp <c.hemp@phytec.de> > > --- > > arch/arm/boot/dts/Makefile | 1 + > > arch/arm/boot/dts/imx6q-phytec-phyflex.dts | 76 ++++++++++++++++++++++++++++ > > 2 files changed, 77 insertions(+) > > create mode 100644 arch/arm/boot/dts/imx6q-phytec-phyflex.dts > > > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > > index 4c58951..6ffdaa1 100644 > > --- a/arch/arm/boot/dts/Makefile > > +++ b/arch/arm/boot/dts/Makefile > > @@ -118,6 +118,7 @@ dtb-$(CONFIG_ARCH_MXC) += \ > > imx6dl-sabresd.dtb \ > > imx6dl-wandboard.dtb \ > > imx6q-arm2.dtb \ > > + imx6q-phytec-phyflex.dtb \ > > imx6q-sabreauto.dtb \ > > imx6q-sabrelite.dtb \ > > imx6q-sabresd.dtb \ > > diff --git a/arch/arm/boot/dts/imx6q-phytec-phyflex.dts b/arch/arm/boot/dts/imx6q-phytec-phyflex.dts > > new file mode 100644 > > index 0000000..9690691 > > --- /dev/null > > +++ b/arch/arm/boot/dts/imx6q-phytec-phyflex.dts > > @@ -0,0 +1,76 @@ > > +/* > > + * Copyright 2013 Christian Hemp, Phytec Messtechnik GmbH > > + * > > + * The code contained herein is licensed under the GNU General Public > > + * License. You may obtain a copy of the GNU General Public License > > + * Version 2 or later at the following locations: > > + * > > + * http://www.opensource.org/licenses/gpl-license.html > > + * http://www.gnu.org/copyleft/gpl.html > > + */ > > + > > +/dts-v1/; > > +#include "imx6q.dtsi" > > + > > +/ { > > + model = "Phytec phyFLEX-i.MX6"; > > + compatible = "phytec,phyflex-imx6", "fsl,imx6q"; > > ditto > > Shawn > > > + > > + memory { > > + reg = <0x10000000 0x80000000>; > > + }; > > +}; > > + > > +&iomuxc { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_hog>; > > + > > + hog { > > + pinctrl_hog: hoggrp { > > + fsl,pins = < > > + MX6Q_PAD_EIM_D23__GPIO3_IO23 0x80000000 > > + >; > > + }; > > + }; > > + > > + phyflex { > > + pinctrl_usdhc3_phyflex: usdhc3grp-phyflex { > > + fsl,pins = < > > + MX6Q_PAD_ENET_RXD0__GPIO1_IO27 0x80000000 > > + MX6Q_PAD_ENET_TXD1__GPIO1_IO29 0x80000000 > > + >; > > + }; > > + }; > > +}; > > + > > +&fec { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_enet_3>; > > + phy-mode = "rgmii"; > > + phy-reset-gpios = <&gpio3 23 0>; > > + status = "okay"; > > +}; > > + > > +&uart4 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_uart4_1>; > > + status = "okay"; > > +}; > > + > > +&usdhc2 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_usdhc2_2>; > > + cd-gpios = <&gpio1 4 0>; > > + wp-gpios = <&gpio1 2 0>; > > + status = "okay"; > > +}; > > + > > +&usdhc3 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_usdhc3_2 > > + &pinctrl_usdhc3_phyflex>; > > + cd-gpios = <&gpio1 27 0>; > > + wp-gpios = <&gpio1 29 0>; > > + status = "okay"; > > +}; > > + > > -- > > 1.7.9.5 > > > > > _______________________________________________ > linux-arm-kernel mailing list > linux-arm-kernel at lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2013-05-31 9:56 UTC | newest] Thread overview: 6+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2013-05-29 21:06 [PATCH 0/2] Add Phytec phyFLEX-i.MX6 board Christian Hemp 2013-05-29 21:06 ` [PATCH 1/2] ARM: dts: imx6q: Add pinctrl for usdhc2 and enet Christian Hemp 2013-05-30 6:25 ` Shawn Guo 2013-05-29 21:06 ` [PATCH 2/2] ARM: dts: Phytec phyFLEX-i.MX6 support Christian Hemp 2013-05-30 6:31 ` Shawn Guo 2013-05-31 9:56 ` Christian Hemp
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox