From: fisaksen@baylibre.com (Frode Isaksen)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v3 6/6] spi: loopback-test: add option to use vmalloc'ed buffers
Date: Thu, 23 Feb 2017 19:02:01 +0100 [thread overview]
Message-ID: <1487872921-26628-7-git-send-email-fisaksen@baylibre.com> (raw)
In-Reply-To: <1487872921-26628-1-git-send-email-fisaksen@baylibre.com>
Using vmalloc'ed buffers will use one SG entry for each page,
that may provoke DMA errors for large transfers.
Also vmalloc'ed buffers may cause errors on CPU's with VIVT cache.
Add this option to catch these errors when testing.
Note that to catch VIVT cache errors, checking the rx range
has to be disabled, so this option has been added as well.
Signed-off-by: Frode Isaksen <fisaksen@baylibre.com>
---
drivers/spi/spi-loopback-test.c | 34 +++++++++++++++++++++++++++-------
1 file changed, 27 insertions(+), 7 deletions(-)
diff --git a/drivers/spi/spi-loopback-test.c b/drivers/spi/spi-loopback-test.c
index 50e620f..3596051 100644
--- a/drivers/spi/spi-loopback-test.c
+++ b/drivers/spi/spi-loopback-test.c
@@ -55,6 +55,18 @@ module_param(run_only_test, int, 0);
MODULE_PARM_DESC(run_only_test,
"only run the test with this number (0-based !)");
+/* use vmalloc'ed buffers */
+int use_vmalloc;
+module_param(use_vmalloc, int, 0644);
+MODULE_PARM_DESC(use_vmalloc,
+ "use vmalloc'ed buffers instead of kmalloc'ed");
+
+/* check rx ranges */
+int check_ranges = 1;
+module_param(check_ranges, int, 0644);
+MODULE_PARM_DESC(check_ranges,
+ "checks rx_buffer pattern are valid");
+
/* the actual tests to execute */
static struct spi_test spi_tests[] = {
{
@@ -492,9 +504,11 @@ static int spi_test_check_loopback_result(struct spi_device *spi,
int ret;
/* checks rx_buffer pattern are valid with loopback or without */
- ret = spi_check_rx_ranges(spi, msg, rx);
- if (ret)
- return ret;
+ if (check_ranges) {
+ ret = spi_check_rx_ranges(spi, msg, rx);
+ if (ret)
+ return ret;
+ }
/* if we run without loopback, then return now */
if (!loopback)
@@ -965,13 +979,19 @@ int spi_test_run_tests(struct spi_device *spi,
/* allocate rx/tx buffers of 128kB size without devm
* in the hope that is on a page boundary
*/
- rx = kzalloc(SPI_TEST_MAX_SIZE_PLUS, GFP_KERNEL);
+ if (use_vmalloc)
+ rx = vmalloc(SPI_TEST_MAX_SIZE_PLUS);
+ else
+ rx = kzalloc(SPI_TEST_MAX_SIZE_PLUS, GFP_KERNEL);
if (!rx) {
ret = -ENOMEM;
goto out;
}
- tx = kzalloc(SPI_TEST_MAX_SIZE_PLUS, GFP_KERNEL);
+ if (use_vmalloc)
+ tx = vmalloc(SPI_TEST_MAX_SIZE_PLUS);
+ else
+ tx = kzalloc(SPI_TEST_MAX_SIZE_PLUS, GFP_KERNEL);
if (!tx) {
ret = -ENOMEM;
goto out;
@@ -999,8 +1019,8 @@ int spi_test_run_tests(struct spi_device *spi,
}
out:
- kfree(rx);
- kfree(tx);
+ kvfree(rx);
+ kvfree(tx);
return ret;
}
EXPORT_SYMBOL_GPL(spi_test_run_tests);
--
2.7.4
next prev parent reply other threads:[~2017-02-23 18:02 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-02-23 18:01 [PATCH v3 0/6] Enable DMA for daVinci SPI controller Frode Isaksen
2017-02-23 18:01 ` [PATCH v3 1/6] spi: davinci: Use SPI framework to handle DMA mapping Frode Isaksen
2017-03-07 14:22 ` Applied "spi: davinci: Use SPI framework to handle DMA mapping" to the spi tree Mark Brown
2017-02-23 18:01 ` [PATCH v3 2/6] spi: davinci: enable DMA when channels are defined in DT Frode Isaksen
2017-02-23 18:01 ` [PATCH v3 3/6] spi: davinci: use rx buffer as dummy tx buffer Frode Isaksen
2017-03-15 19:35 ` Mark Brown
2017-02-23 18:01 ` [PATCH v3 4/6] spi: davinci: do not use DMA if transfer length is less than 16 Frode Isaksen
2017-03-15 19:37 ` Applied "spi: davinci: do not use DMA if transfer length is less than 16" to the spi tree Mark Brown
2017-02-23 18:02 ` [PATCH v3 5/6] spi: davinci: do not use DMA for vmalloc'ed buffers Frode Isaksen
2017-03-15 19:37 ` Applied "spi: davinci: do not use DMA for vmalloc'ed buffers" to the spi tree Mark Brown
2017-02-23 18:02 ` Frode Isaksen [this message]
2017-03-16 14:11 ` Applied "spi: loopback-test: add option to use " Mark Brown
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1487872921-26628-7-git-send-email-fisaksen@baylibre.com \
--to=fisaksen@baylibre.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox