[PATCH v7 0/4] Add peripherals for J784S4

[PATCH v7 0/4] Add peripherals for J784S4

[Jayesh Choudhary]

This series adds support for:
- SERDES, WIZ DT nodes, Serdes lane control mux
- DSS and DisplayPort-0 nodes

This support DEPENDS upon another series which was introduced as part
of discussion in v5. That series[1] moves the ti-serdes headers file
from bindings to "arch/arm64/boot/dts/ti". (That series is merged in
linux-next tree)

Changelog v6->v7:
- change compatible for scm_conf to 'simple-bus'
- drop main_cpsw node due to driver dependency on [2]

Changelog v5->v6:
- Change header file according to [1].
- Add idle-state property in serdes_ln_ctrl node.
- Fix dtbs_check warning due to clock-frequency property in serdes_refclk
  node by disabling the node in main.dtsi and enabling it in board file
  when the clock-frequency node is actually added.

Changelog v4->v5:
- rebased the patches on linux-next tip.

Changelog v3->v4:
- add reg property to serdes_ln_ctrl and fix the node name again to
  get rid of dtbs_check error.
- reorder reg, reg-names and ranges property for main_cpsw1.
- correct the order for clocks in serdes_wiz nodes to fix dtbs_check
  warnings.
- fix indentation in reg, reg-names and clock property for dss node.
- add comments for the reg type in dss registers.

Changelog v3->v2:
- fix dtc warnings for 'scm_conf' and 'serdes_ln_ctrl' nodes
  (Checked all the changes of the series with W=12 option during build)
- added clock-frequency for serdes_refclk along with other EVM changes
  This refclk is being used by all the instances of serdes_wiz which
  are disabled by default. So configuring refclk when the serdes nodes
  are used for the first time is okay.

Changelog v1->v2:
- Moved J784S4 EVM changes together to the last patch
  (Suggested by Andrew)

v5 patch link:
<https://lore.kernel.org/all/20230721132029.123881-1-j-choudhary@ti.com/>

[1]: <https://lore.kernel.org/all/20230721125732.122421-1-j-choudhary@ti.com/>
[2]: <https://lore.kernel.org/all/20230605154153.24025-1-afd@ti.com/>

Rahul T R (2):
  arm64: dts: ti: k3-j784s4-main: Add DSS and DP-bridge node
  arm64: dts: ti: k3-j784s4-evm: Enable DisplayPort-0

Siddharth Vadapalli (2):
  arm64: dts: ti: k3-j784s4-main: Add system controller and SERDES lane
    mux
  arm64: dts: ti: k3-j784s4: Add WIZ and SERDES PHY nodes

 arch/arm64/boot/dts/ti/k3-j784s4-evm.dts   | 117 +++++++++
 arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi | 285 +++++++++++++++++++++
 2 files changed, 402 insertions(+)

-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v7 1/4] arm64: dts: ti: k3-j784s4-main: Add system controller and SERDES lane mux

[Jayesh Choudhary]

From: Siddharth Vadapalli <s-vadapalli@ti.com>

The system controller node manages the CTRL_MMR0 region.
Add serdes_ln_ctrl node which is used for controlling the SERDES lane mux.

Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
[j-choudhary@ti.com: Fix serdes_ln_ctrl node]
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
---
 arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi | 40 ++++++++++++++++++++++
 1 file changed, 40 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
index 11f163e5cadf..8a816563706b 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
@@ -5,6 +5,10 @@
  * Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com/
  */
 
+#include <dt-bindings/mux/mux.h>
+
+#include "k3-serdes.h"
+
 &cbass_main {
 	msmc_ram: sram@70000000 {
 		compatible = "mmio-sram";
@@ -26,6 +30,42 @@ l3cache-sram@200000 {
 		};
 	};
 
+	scm_conf: bus@100000 {
+		compatible = "simple-bus";
+		reg = <0x00 0x00100000 0x00 0x1c000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x00 0x00 0x00100000 0x1c000>;
+
+		serdes_ln_ctrl: mux-controller@4080 {
+			compatible = "mmio-mux";
+			reg = <0x00004080 0x30>;
+			#mux-control-cells = <1>;
+			mux-reg-masks = <0x4080 0x3>, <0x4084 0x3>, /* SERDES0 lane0/1 select */
+					<0x4088 0x3>, <0x408c 0x3>, /* SERDES0 lane2/3 select */
+					<0x4090 0x3>, <0x4094 0x3>, /* SERDES1 lane0/1 select */
+					<0x4098 0x3>, <0x409c 0x3>, /* SERDES1 lane2/3 select */
+					<0x40a0 0x3>, <0x40a4 0x3>, /* SERDES2 lane0/1 select */
+					<0x40a8 0x3>, <0x40ac 0x3>; /* SERDES2 lane2/3 select */
+			idle-states = <J784S4_SERDES0_LANE0_PCIE1_LANE0>,
+				      <J784S4_SERDES0_LANE1_PCIE1_LANE1>,
+				      <J784S4_SERDES0_LANE2_IP3_UNUSED>,
+				      <J784S4_SERDES0_LANE3_USB>,
+				      <J784S4_SERDES1_LANE0_PCIE0_LANE0>,
+				      <J784S4_SERDES1_LANE1_PCIE0_LANE1>,
+				      <J784S4_SERDES1_LANE2_PCIE0_LANE2>,
+				      <J784S4_SERDES1_LANE3_PCIE0_LANE3>,
+				      <J784S4_SERDES2_LANE0_IP2_UNUSED>,
+				      <J784S4_SERDES2_LANE1_IP2_UNUSED>,
+				      <J784S4_SERDES2_LANE2_QSGMII_LANE1>,
+				      <J784S4_SERDES2_LANE3_QSGMII_LANE2>,
+				      <J784S4_SERDES4_LANE0_EDP_LANE0>,
+				      <J784S4_SERDES4_LANE1_EDP_LANE1>,
+				      <J784S4_SERDES4_LANE2_EDP_LANE2>,
+				      <J784S4_SERDES4_LANE3_EDP_LANE3>;
+		};
+	};
+
 	gic500: interrupt-controller@1800000 {
 		compatible = "arm,gic-v3";
 		#address-cells = <2>;
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v7 2/4] arm64: dts: ti: k3-j784s4: Add WIZ and SERDES PHY nodes

[Jayesh Choudhary]

From: Siddharth Vadapalli <s-vadapalli@ti.com>

J784S4 SoC has 4 Serdes instances along with their respective WIZ
instances. Add device-tree nodes for them and disable them by default.

Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
[j-choudhary@ti.com: fix serdes_wiz clock order & disable serdes refclk]
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
---
 arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi | 172 +++++++++++++++++++++
 1 file changed, 172 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
index 8a816563706b..fbf5ab94d785 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
@@ -6,9 +6,19 @@
  */
 
 #include <dt-bindings/mux/mux.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/phy/phy-ti.h>
 
 #include "k3-serdes.h"
 
+/ {
+	serdes_refclk: serdes-refclk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		status = "disabled";
+	};
+};
+
 &cbass_main {
 	msmc_ram: sram@70000000 {
 		compatible = "mmio-sram";
@@ -709,6 +719,168 @@ main_sdhci1: mmc@4fb0000 {
 		status = "disabled";
 	};
 
+	serdes_wiz0: wiz@5060000 {
+		compatible = "ti,j784s4-wiz-10g";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		power-domains = <&k3_pds 404 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 404 2>, <&k3_clks 404 6>, <&serdes_refclk>, <&k3_clks 404 5>;
+		clock-names = "fck", "core_ref_clk", "ext_ref_clk", "core_ref1_clk";
+		assigned-clocks = <&k3_clks 404 6>;
+		assigned-clock-parents = <&k3_clks 404 10>;
+		num-lanes = <4>;
+		#reset-cells = <1>;
+		#clock-cells = <1>;
+		ranges = <0x5060000 0x00 0x5060000 0x10000>;
+
+		status = "disabled";
+
+		serdes0: serdes@5060000 {
+			compatible = "ti,j721e-serdes-10g";
+			reg = <0x05060000 0x010000>;
+			reg-names = "torrent_phy";
+			resets = <&serdes_wiz0 0>;
+			reset-names = "torrent_reset";
+			clocks = <&serdes_wiz0 TI_WIZ_PLL0_REFCLK>,
+				 <&serdes_wiz0 TI_WIZ_PHY_EN_REFCLK>;
+			clock-names = "refclk", "phy_en_refclk";
+			assigned-clocks = <&serdes_wiz0 TI_WIZ_PLL0_REFCLK>,
+					  <&serdes_wiz0 TI_WIZ_PLL1_REFCLK>,
+					  <&serdes_wiz0 TI_WIZ_REFCLK_DIG>;
+			assigned-clock-parents = <&k3_clks 404 6>,
+						 <&k3_clks 404 6>,
+						 <&k3_clks 404 6>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#clock-cells = <1>;
+
+			status = "disabled";
+		};
+	};
+
+	serdes_wiz1: wiz@5070000 {
+		compatible = "ti,j784s4-wiz-10g";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		power-domains = <&k3_pds 405 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 405 2>, <&k3_clks 405 6>, <&serdes_refclk>, <&k3_clks 405 5>;
+		clock-names = "fck", "core_ref_clk", "ext_ref_clk", "core_ref1_clk";
+		assigned-clocks = <&k3_clks 405 6>;
+		assigned-clock-parents = <&k3_clks 405 10>;
+		num-lanes = <4>;
+		#reset-cells = <1>;
+		#clock-cells = <1>;
+		ranges = <0x05070000 0x00 0x05070000 0x10000>;
+
+		status = "disabled";
+
+		serdes1: serdes@5070000 {
+			compatible = "ti,j721e-serdes-10g";
+			reg = <0x05070000 0x010000>;
+			reg-names = "torrent_phy";
+			resets = <&serdes_wiz1 0>;
+			reset-names = "torrent_reset";
+			clocks = <&serdes_wiz1 TI_WIZ_PLL0_REFCLK>,
+				 <&serdes_wiz1 TI_WIZ_PHY_EN_REFCLK>;
+			clock-names = "refclk", "phy_en_refclk";
+			assigned-clocks = <&serdes_wiz1 TI_WIZ_PLL0_REFCLK>,
+					  <&serdes_wiz1 TI_WIZ_PLL1_REFCLK>,
+					  <&serdes_wiz1 TI_WIZ_REFCLK_DIG>;
+			assigned-clock-parents = <&k3_clks 405 6>,
+						 <&k3_clks 405 6>,
+						 <&k3_clks 405 6>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#clock-cells = <1>;
+
+			status = "disabled";
+		};
+	};
+
+	serdes_wiz2: wiz@5020000 {
+		compatible = "ti,j784s4-wiz-10g";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		power-domains = <&k3_pds 406 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 406 2>, <&k3_clks 406 6>, <&serdes_refclk>, <&k3_clks 406 5>;
+		clock-names = "fck", "core_ref_clk", "ext_ref_clk", "core_ref1_clk";
+		assigned-clocks = <&k3_clks 406 6>;
+		assigned-clock-parents = <&k3_clks 406 10>;
+		num-lanes = <4>;
+		#reset-cells = <1>;
+		#clock-cells = <1>;
+		ranges = <0x05020000 0x00 0x05020000 0x10000>;
+
+		status = "disabled";
+
+		serdes2: serdes@5020000 {
+			compatible = "ti,j721e-serdes-10g";
+			reg = <0x05020000 0x010000>;
+			reg-names = "torrent_phy";
+			resets = <&serdes_wiz2 0>;
+			reset-names = "torrent_reset";
+			clocks = <&serdes_wiz2 TI_WIZ_PLL0_REFCLK>,
+				 <&serdes_wiz2 TI_WIZ_PHY_EN_REFCLK>;
+			clock-names = "refclk", "phy_en_refclk";
+			assigned-clocks = <&serdes_wiz2 TI_WIZ_PLL0_REFCLK>,
+					  <&serdes_wiz2 TI_WIZ_PLL1_REFCLK>,
+					  <&serdes_wiz2 TI_WIZ_REFCLK_DIG>;
+			assigned-clock-parents = <&k3_clks 406 6>,
+						 <&k3_clks 406 6>,
+						 <&k3_clks 406 6>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#clock-cells = <1>;
+
+			status = "disabled";
+		};
+	};
+
+	serdes_wiz4: wiz@5050000 {
+		compatible = "ti,j784s4-wiz-10g";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		power-domains = <&k3_pds 407 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 407 2>, <&k3_clks 407 6>, <&serdes_refclk>, <&k3_clks 407 5>;
+		clock-names = "fck", "core_ref_clk", "ext_ref_clk", "core_ref1_clk";
+		assigned-clocks = <&k3_clks 407 6>;
+		assigned-clock-parents = <&k3_clks 407 10>;
+		num-lanes = <4>;
+		#reset-cells = <1>;
+		#clock-cells = <1>;
+		ranges = <0x05050000 0x00 0x05050000 0x10000>,
+			 <0xa030a00 0x00 0xa030a00 0x40>; /* DPTX PHY */
+
+		status = "disabled";
+
+		serdes4: serdes@5050000 {
+			/*
+			 * Note: we also map DPTX PHY registers as the Torrent
+			 * needs to manage those.
+			 */
+			compatible = "ti,j721e-serdes-10g";
+			reg = <0x05050000 0x010000>,
+			      <0x0a030a00 0x40>; /* DPTX PHY */
+			reg-names = "torrent_phy";
+			resets = <&serdes_wiz4 0>;
+			reset-names = "torrent_reset";
+			clocks = <&serdes_wiz4 TI_WIZ_PLL0_REFCLK>,
+				 <&serdes_wiz4 TI_WIZ_PHY_EN_REFCLK>;
+			clock-names = "refclk", "phy_en_refclk";
+			assigned-clocks = <&serdes_wiz4 TI_WIZ_PLL0_REFCLK>,
+					  <&serdes_wiz4 TI_WIZ_PLL1_REFCLK>,
+					  <&serdes_wiz4 TI_WIZ_REFCLK_DIG>;
+			assigned-clock-parents = <&k3_clks 407 6>,
+						 <&k3_clks 407 6>,
+						 <&k3_clks 407 6>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#clock-cells = <1>;
+
+			status = "disabled";
+		};
+	};
+
 	main_navss: bus@30000000 {
 		compatible = "simple-bus";
 		#address-cells = <2>;
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v7 3/4] arm64: dts: ti: k3-j784s4-main: Add DSS and DP-bridge node

[Jayesh Choudhary]

From: Rahul T R <r-ravikumar@ti.com>

Add DSS and DP-bridge node for J784S4 SoC. DSS IP in J784S4 is
same as DSS IP in J721E, so same compatible is being used.
The DP is Cadence MHDP8546.

Signed-off-by: Rahul T R <r-ravikumar@ti.com>
[j-choudhary@ti.com: move dss & mhdp node together in main, fix dss node]
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
---
 arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi | 73 ++++++++++++++++++++++
 1 file changed, 73 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
index fbf5ab94d785..975661948755 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
@@ -1749,4 +1749,77 @@ c71_3: dsp@67800000 {
 		resets = <&k3_reset 40 1>;
 		firmware-name = "j784s4-c71_3-fw";
 	};
+
+	mhdp: dp-bridge@a000000 {
+		compatible = "ti,j721e-mhdp8546";
+
+		reg = <0x0 0xa000000 0x0 0x30a00>,
+		      <0x0 0x4f40000 0x0 0x20>;
+		reg-names = "mhdptx", "j721e-intg";
+
+		clocks = <&k3_clks 217 11>;
+
+		interrupt-parent = <&gic500>;
+		interrupts = <GIC_SPI 614 IRQ_TYPE_LEVEL_HIGH>;
+
+		power-domains = <&k3_pds 217 TI_SCI_PD_EXCLUSIVE>;
+
+		status = "disabled";
+
+		dp0_ports: ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+
+	dss: dss@4a00000 {
+		compatible = "ti,j721e-dss";
+		reg = <0x00 0x04a00000 0x00 0x10000>, /* common_m */
+		      <0x00 0x04a10000 0x00 0x10000>, /* common_s0*/
+		      <0x00 0x04b00000 0x00 0x10000>, /* common_s1*/
+		      <0x00 0x04b10000 0x00 0x10000>, /* common_s2*/
+		      <0x00 0x04a20000 0x00 0x10000>, /* vidl1 */
+		      <0x00 0x04a30000 0x00 0x10000>, /* vidl2 */
+		      <0x00 0x04a50000 0x00 0x10000>, /* vid1 */
+		      <0x00 0x04a60000 0x00 0x10000>, /* vid2 */
+		      <0x00 0x04a70000 0x00 0x10000>, /* ovr1 */
+		      <0x00 0x04a90000 0x00 0x10000>, /* ovr2 */
+		      <0x00 0x04ab0000 0x00 0x10000>, /* ovr3 */
+		      <0x00 0x04ad0000 0x00 0x10000>, /* ovr4 */
+		      <0x00 0x04a80000 0x00 0x10000>, /* vp1 */
+		      <0x00 0x04aa0000 0x00 0x10000>, /* vp1 */
+		      <0x00 0x04ac0000 0x00 0x10000>, /* vp1 */
+		      <0x00 0x04ae0000 0x00 0x10000>, /* vp4 */
+		      <0x00 0x04af0000 0x00 0x10000>; /* wb */
+
+		reg-names = "common_m", "common_s0",
+			    "common_s1", "common_s2",
+			    "vidl1", "vidl2","vid1","vid2",
+			    "ovr1", "ovr2", "ovr3", "ovr4",
+			    "vp1", "vp2", "vp3", "vp4",
+			    "wb";
+
+		clocks = <&k3_clks 218 0>,
+			 <&k3_clks 218 2>,
+			 <&k3_clks 218 5>,
+			 <&k3_clks 218 14>,
+			 <&k3_clks 218 18>;
+		clock-names = "fck", "vp1", "vp2", "vp3", "vp4";
+
+		power-domains = <&k3_pds 218 TI_SCI_PD_EXCLUSIVE>;
+
+		interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "common_m",
+				  "common_s0",
+				  "common_s1",
+				  "common_s2";
+
+		status = "disabled";
+
+		dss_ports: ports {
+		};
+	};
 };
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v7 4/4] arm64: dts: ti: k3-j784s4-evm: Enable DisplayPort-0

[Jayesh Choudhary]

From: Rahul T R <r-ravikumar@ti.com>

Enable display for J784S4 EVM.

Add assigned clocks for DSS, DT node for DisplayPort PHY and pinmux for
DP HPD. Add the clock frequency for serdes_refclk.

Add the endpoint nodes to describe connection from:
DSS => MHDP => DisplayPort connector.

Also add the GPIO expander-4 node and pinmux for main_i2c4 which is
required for controlling DP power. Set status for all required nodes
for DP-0 as "okay".

Signed-off-by: Rahul T R <r-ravikumar@ti.com>
[j-choudhary@ti.com: move all the changes together to enable DP-0 in EVM]
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
---
 arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 117 +++++++++++++++++++++++
 1 file changed, 117 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
index 7ad152a1b90f..1145a7f046e2 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
@@ -249,6 +249,28 @@ vdd_sd_dv: regulator-TLV71033 {
 		states = <1800000 0x0>,
 			 <3300000 0x1>;
 	};
+
+	dp0_pwr_3v3: regulator-dp0-prw {
+		compatible = "regulator-fixed";
+		regulator-name = "dp0-pwr";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&exp4 0 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	dp0: dp0-connector {
+		compatible = "dp-connector";
+		label = "DP0";
+		type = "full-size";
+		dp-pwr-supply = <&dp0_pwr_3v3>;
+
+		port {
+			dp0_connector_in: endpoint {
+				remote-endpoint = <&dp0_out>;
+			};
+		};
+	};
 };
 
 &main_pmx0 {
@@ -286,6 +308,19 @@ vdd_sd_dv_pins_default: vdd-sd-dv-default-pins {
 			J784S4_IOPAD(0x020, PIN_INPUT, 7) /* (AJ35) MCAN15_RX.GPIO0_8 */
 		>;
 	};
+
+	dp0_pins_default: dp0-pins-default {
+		pinctrl-single,pins = <
+			J784S4_IOPAD(0x0cc, PIN_INPUT, 12) /* (AM37) SPI0_CS0.DP0_HPD */
+		>;
+	};
+
+	main_i2c4_pins_default: main-i2c4-pins-default {
+		pinctrl-single,pins = <
+			J784S4_IOPAD(0x014, PIN_INPUT_PULLUP, 8) /* (AG33) MCAN14_TX.I2C4_SCL */
+			J784S4_IOPAD(0x010, PIN_INPUT_PULLUP, 8) /* (AH33) MCAN13_RX.I2C4_SDA */
+		>;
+	};
 };
 
 &wkup_pmx2 {
@@ -827,3 +862,85 @@ adc {
 		ti,adc-channels = <0 1 2 3 4 5 6 7>;
 	};
 };
+
+&serdes_refclk {
+	status = "okay";
+	clock-frequency = <100000000>;
+};
+
+&dss {
+	status = "okay";
+	assigned-clocks = <&k3_clks 218 2>,
+			  <&k3_clks 218 5>,
+			  <&k3_clks 218 14>,
+			  <&k3_clks 218 18>;
+	assigned-clock-parents = <&k3_clks 218 3>,
+				 <&k3_clks 218 7>,
+				 <&k3_clks 218 16>,
+				 <&k3_clks 218 22>;
+};
+
+&serdes_wiz4 {
+	status = "okay";
+};
+
+&serdes4 {
+	status = "okay";
+	serdes4_dp_link: phy@0 {
+		reg = <0>;
+		cdns,num-lanes = <4>;
+		#phy-cells = <0>;
+		cdns,phy-type = <PHY_TYPE_DP>;
+		resets = <&serdes_wiz4 1>, <&serdes_wiz4 2>,
+			 <&serdes_wiz4 3>, <&serdes_wiz4 4>;
+	};
+};
+
+&mhdp {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&dp0_pins_default>;
+	phys = <&serdes4_dp_link>;
+	phy-names = "dpphy";
+};
+
+&dss_ports {
+	port {
+		dpi0_out: endpoint {
+			remote-endpoint = <&dp0_in>;
+		};
+	};
+};
+
+&main_i2c4 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_i2c4_pins_default>;
+	clock-frequency = <400000>;
+
+	exp4: gpio@20 {
+		compatible = "ti,tca6408";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+};
+
+&dp0_ports {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	port@0 {
+		reg = <0>;
+		dp0_in: endpoint {
+			remote-endpoint = <&dpi0_out>;
+		};
+	};
+
+	port@4 {
+		reg = <4>;
+		dp0_out: endpoint {
+			remote-endpoint = <&dp0_connector_in>;
+		};
+	};
+};
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v7 0/4] Add peripherals for J784S4

[Nishanth Menon]

On 10:38-20230728, Jayesh Choudhary wrote:
> This series adds support for:
> - SERDES, WIZ DT nodes, Serdes lane control mux
> - DSS and DisplayPort-0 nodes
> 
> This support DEPENDS upon another series which was introduced as part
> of discussion in v5. That series[1] moves the ti-serdes headers file
> from bindings to "arch/arm64/boot/dts/ti". (That series is merged in
> linux-next tree)
> 
> Changelog v6->v7:
> - change compatible for scm_conf to 'simple-bus'
> - drop main_cpsw node due to driver dependency on [2]
> 
> Changelog v5->v6:
> - Change header file according to [1].
> - Add idle-state property in serdes_ln_ctrl node.
> - Fix dtbs_check warning due to clock-frequency property in serdes_refclk
>   node by disabling the node in main.dtsi and enabling it in board file
>   when the clock-frequency node is actually added.
> 
> Changelog v4->v5:
> - rebased the patches on linux-next tip.
> 
> Changelog v3->v4:
> - add reg property to serdes_ln_ctrl and fix the node name again to
>   get rid of dtbs_check error.
> - reorder reg, reg-names and ranges property for main_cpsw1.
> - correct the order for clocks in serdes_wiz nodes to fix dtbs_check
>   warnings.
> - fix indentation in reg, reg-names and clock property for dss node.
> - add comments for the reg type in dss registers.
> 
> Changelog v3->v2:
> - fix dtc warnings for 'scm_conf' and 'serdes_ln_ctrl' nodes
>   (Checked all the changes of the series with W=12 option during build)
> - added clock-frequency for serdes_refclk along with other EVM changes
>   This refclk is being used by all the instances of serdes_wiz which
>   are disabled by default. So configuring refclk when the serdes nodes
>   are used for the first time is okay.
> 
> Changelog v1->v2:
> - Moved J784S4 EVM changes together to the last patch
>   (Suggested by Andrew)
> 
> v5 patch link:
> <https://lore.kernel.org/all/20230721132029.123881-1-j-choudhary@ti.com/>
> 
> [1]: <https://lore.kernel.org/all/20230721125732.122421-1-j-choudhary@ti.com/>
> [2]: <https://lore.kernel.org/all/20230605154153.24025-1-afd@ti.com/>
> 
> Rahul T R (2):
>   arm64: dts: ti: k3-j784s4-main: Add DSS and DP-bridge node
>   arm64: dts: ti: k3-j784s4-evm: Enable DisplayPort-0
> 

Could you enable AM69-SK as well? is there anything stopping it being part of the series?

-- 
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v7 0/4] Add peripherals for J784S4

[Jayesh Choudhary]

Hello Nishanth,

On 29/07/23 02:42, Nishanth Menon wrote:
> On 10:38-20230728, Jayesh Choudhary wrote:
>> This series adds support for:
>> - SERDES, WIZ DT nodes, Serdes lane control mux
>> - DSS and DisplayPort-0 nodes
>>
>> This support DEPENDS upon another series which was introduced as part
>> of discussion in v5. That series[1] moves the ti-serdes headers file
>> from bindings to "arch/arm64/boot/dts/ti". (That series is merged in
>> linux-next tree)
>>
>> Changelog v6->v7:
>> - change compatible for scm_conf to 'simple-bus'
>> - drop main_cpsw node due to driver dependency on [2]
>>

[...]

>>
>> v5 patch link:
>> <https://lore.kernel.org/all/20230721132029.123881-1-j-choudhary@ti.com/>
>>
>> [1]: <https://lore.kernel.org/all/20230721125732.122421-1-j-choudhary@ti.com/>
>> [2]: <https://lore.kernel.org/all/20230605154153.24025-1-afd@ti.com/>
>>
>> Rahul T R (2):
>>    arm64: dts: ti: k3-j784s4-main: Add DSS and DP-bridge node
>>    arm64: dts: ti: k3-j784s4-evm: Enable DisplayPort-0
>>
> 
> Could you enable AM69-SK as well? is there anything stopping it being part of the series?
> 

Okay I will add support for AM69-SK too.

Thanks,
-Jayesh

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel