[PATCH 00/18] clk: imx: misc update/fix

[PATCH 00/18] clk: imx: misc update/fix

[Peng Fan (OSS)]

Upstream several patches landed in NXP downstream repo for some time.
- i.MX8M/93/7ULP composite clk update
- Fix Fracn-gppll MFN got lost
- PLL14xx update
- i.MX8MP DRAM CLK fix
- i.MX8MM/N misc update
- Init i.MX8QXP parent clk before child clk

Downstream tags are kept for the patches got R-b

Although there are a few fixes, non-urgent for 6.9.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
Adrian Alonso (1):
      clk: imx: imx8mn: add sai7_ipg_clk clock settings

Florin Pavelescu (1):
      clk: imx: pll14xx: potential integer overflow eliminated by casting to u64

Jacky Bai (2):
      clk: imx: composite-93: keep root clock on when mcore enabled
      clk: imx: imx8mm: Change the 'nand_usdhc_bus' clock to non-critical one

Oliver F. Brown (1):
      clk: imx: imx8qxp: Add clock muxes for MIPI and PHY ref clocks

Peng Fan (8):
      clk: imx: composite-8m: Enable gate clk with mcore_booted
      clk: imx: imx8mp-audiomix: remove sdma root clock
      clk: imx: Remove CLK_SET_PARENT_GATE for DRAM mux for i.MX7D
      clk: imx: add CLK_SET_RATE_PARENT for lcdif_pixel_src for i.MX7D
      clk: imx: imx8qxp: Add LVDS bypass clocks
      clk: imx: imx8qxp: Register dc0_bypass0_clk before disp clk
      clk: imx: imx8qxp: Parent should be initialized earlier than the clock
      clk: imx: fracn-gppll: update rate table

Pengfei Li (1):
      clk: imx: fracn-gppll: fix fractional part of PLL getting lost

Shengjiu Wang (2):
      clk: imx: pll14xx: Add constraint for fvco frequency
      clk: imx: pll14xx: use rate_table for audio plls

Ye Li (1):
      clk: imx: composite-7ulp: Check the PCC present bit

Zhipeng Wang (1):
      clk: imx: imx8mp: fix clock tree update of TF-A managed clocks

 drivers/clk/imx/clk-composite-7ulp.c  |  5 ++++
 drivers/clk/imx/clk-composite-8m.c    | 53 +++++++++++++++++++++++++++--------
 drivers/clk/imx/clk-composite-93.c    | 15 +++++-----
 drivers/clk/imx/clk-fracn-gppll.c     |  6 ++++
 drivers/clk/imx/clk-imx7d.c           |  6 ++--
 drivers/clk/imx/clk-imx8mm.c          |  2 +-
 drivers/clk/imx/clk-imx8mn.c          |  1 +
 drivers/clk/imx/clk-imx8mp-audiomix.c |  1 -
 drivers/clk/imx/clk-imx8mp.c          |  4 +--
 drivers/clk/imx/clk-imx8qxp.c         | 51 +++++++++++++++++++++------------
 drivers/clk/imx/clk-pll14xx.c         | 21 ++++++++++++--
 11 files changed, 120 insertions(+), 45 deletions(-)
---
base-commit: 9221b2819b8a4196eecf5476d66201be60fbcf29
change-id: 20240503-imx-clk-a45b6ce7c15a

Best regards,
-- 
Peng Fan <peng.fan@nxp.com>


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 01/18] clk: imx: composite-8m: Enable gate clk with mcore_booted

[Peng Fan (OSS)]

From: Peng Fan <peng.fan@nxp.com>

Bootloader might disable some CCM ROOT Slices. So if mcore_booted set with
display CCM ROOT disabled by Bootloader, kernel display BLK CTRL driver
imx8m_blk_ctrl_driver_init may hang the system because the BUS clk is
disabled.

Add back gate ops, but with disable doing nothing, then the CCM ROOT
will be enabled when used.

Fixes: 489bbee0c983 ("clk: imx: composite-8m: Enable gate clk with mcore_booted")
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
 drivers/clk/imx/clk-composite-8m.c | 53 ++++++++++++++++++++++++++++++--------
 1 file changed, 42 insertions(+), 11 deletions(-)

diff --git a/drivers/clk/imx/clk-composite-8m.c b/drivers/clk/imx/clk-composite-8m.c
index 8cc07d056a83..f187582ba491 100644
--- a/drivers/clk/imx/clk-composite-8m.c
+++ b/drivers/clk/imx/clk-composite-8m.c
@@ -204,6 +204,34 @@ static const struct clk_ops imx8m_clk_composite_mux_ops = {
 	.determine_rate = imx8m_clk_composite_mux_determine_rate,
 };
 
+static int imx8m_clk_composite_gate_enable(struct clk_hw *hw)
+{
+	struct clk_gate *gate = to_clk_gate(hw);
+	unsigned long flags;
+	u32 val;
+
+	spin_lock_irqsave(gate->lock, flags);
+
+	val = readl(gate->reg);
+	val |= BIT(gate->bit_idx);
+	writel(val, gate->reg);
+
+	spin_unlock_irqrestore(gate->lock, flags);
+
+	return 0;
+}
+
+static void imx8m_clk_composite_gate_disable(struct clk_hw *hw)
+{
+	/* composite clk requires the disable hook */
+}
+
+static const struct clk_ops imx8m_clk_composite_gate_ops = {
+	.enable = imx8m_clk_composite_gate_enable,
+	.disable = imx8m_clk_composite_gate_disable,
+	.is_enabled = clk_gate_is_enabled,
+};
+
 struct clk_hw *__imx8m_clk_hw_composite(const char *name,
 					const char * const *parent_names,
 					int num_parents, void __iomem *reg,
@@ -217,6 +245,7 @@ struct clk_hw *__imx8m_clk_hw_composite(const char *name,
 	struct clk_mux *mux;
 	const struct clk_ops *divider_ops;
 	const struct clk_ops *mux_ops;
+	const struct clk_ops *gate_ops;
 
 	mux = kzalloc(sizeof(*mux), GFP_KERNEL);
 	if (!mux)
@@ -257,20 +286,22 @@ struct clk_hw *__imx8m_clk_hw_composite(const char *name,
 	div->flags = CLK_DIVIDER_ROUND_CLOSEST;
 
 	/* skip registering the gate ops if M4 is enabled */
-	if (!mcore_booted) {
-		gate = kzalloc(sizeof(*gate), GFP_KERNEL);
-		if (!gate)
-			goto free_div;
-
-		gate_hw = &gate->hw;
-		gate->reg = reg;
-		gate->bit_idx = PCG_CGC_SHIFT;
-		gate->lock = &imx_ccm_lock;
-	}
+	gate = kzalloc(sizeof(*gate), GFP_KERNEL);
+	if (!gate)
+		goto free_div;
+
+	gate_hw = &gate->hw;
+	gate->reg = reg;
+	gate->bit_idx = PCG_CGC_SHIFT;
+	gate->lock = &imx_ccm_lock;
+	if (!mcore_booted)
+		gate_ops = &clk_gate_ops;
+	else
+		gate_ops = &imx8m_clk_composite_gate_ops;
 
 	hw = clk_hw_register_composite(NULL, name, parent_names, num_parents,
 			mux_hw, mux_ops, div_hw,
-			divider_ops, gate_hw, &clk_gate_ops, flags);
+			divider_ops, gate_hw, gate_ops, flags);
 	if (IS_ERR(hw))
 		goto free_gate;
 

-- 
2.37.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 02/18] clk: imx: composite-93: keep root clock on when mcore enabled

[Peng Fan (OSS)]

From: Jacky Bai <ping.bai@nxp.com>

Previously we assumed that the root clock slice is enabled
by default when kernel boot up. But the bootloader may disable
the clocks before jump into kernel. The gate ops should be registered
rather than NULL to make sure the disabled clock can be enabled
when kernel boot up.  Refine the code to skip disable the clock
if mcore booted.

Fixes: a740d7350ff7 ("clk: imx: imx93: add mcore_booted module paratemter")
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Chancel Liu <chancel.liu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
 drivers/clk/imx/clk-composite-93.c | 15 ++++++++-------
 1 file changed, 8 insertions(+), 7 deletions(-)

diff --git a/drivers/clk/imx/clk-composite-93.c b/drivers/clk/imx/clk-composite-93.c
index 81164bdcd6cc..6c6c5a30f328 100644
--- a/drivers/clk/imx/clk-composite-93.c
+++ b/drivers/clk/imx/clk-composite-93.c
@@ -76,6 +76,13 @@ static int imx93_clk_composite_gate_enable(struct clk_hw *hw)
 
 static void imx93_clk_composite_gate_disable(struct clk_hw *hw)
 {
+	/*
+	 * Skip disable the root clock gate if mcore enabled.
+	 * The root clock may be used by the mcore.
+	 */
+	if (mcore_booted)
+		return;
+
 	imx93_clk_composite_gate_endisable(hw, 0);
 }
 
@@ -222,7 +229,7 @@ struct clk_hw *imx93_clk_composite_flags(const char *name, const char * const *p
 		hw = clk_hw_register_composite(NULL, name, parent_names, num_parents,
 					       mux_hw, &clk_mux_ro_ops, div_hw,
 					       &clk_divider_ro_ops, NULL, NULL, flags);
-	} else if (!mcore_booted) {
+	} else {
 		gate = kzalloc(sizeof(*gate), GFP_KERNEL);
 		if (!gate)
 			goto fail;
@@ -238,12 +245,6 @@ struct clk_hw *imx93_clk_composite_flags(const char *name, const char * const *p
 					       &imx93_clk_composite_divider_ops, gate_hw,
 					       &imx93_clk_composite_gate_ops,
 					       flags | CLK_SET_RATE_NO_REPARENT);
-	} else {
-		hw = clk_hw_register_composite(NULL, name, parent_names, num_parents,
-					       mux_hw, &imx93_clk_composite_mux_ops, div_hw,
-					       &imx93_clk_composite_divider_ops, NULL,
-					       &imx93_clk_composite_gate_ops,
-					       flags | CLK_SET_RATE_NO_REPARENT);
 	}
 
 	if (IS_ERR(hw))

-- 
2.37.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 03/18] clk: imx: composite-7ulp: Check the PCC present bit

[Peng Fan (OSS)]

From: Ye Li <ye.li@nxp.com>

When some module is disabled by fuse, its PCC PR bit is default 0 and
PCC is not operational. Any write to this PCC will cause SError.

Fixes: b40ba8065347 ("clk: imx: Update the compsite driver to support imx8ulp")
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
 drivers/clk/imx/clk-composite-7ulp.c | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/drivers/clk/imx/clk-composite-7ulp.c b/drivers/clk/imx/clk-composite-7ulp.c
index e208ddc51133..e70a03e7299c 100644
--- a/drivers/clk/imx/clk-composite-7ulp.c
+++ b/drivers/clk/imx/clk-composite-7ulp.c
@@ -14,6 +14,7 @@
 #include "../clk-fractional-divider.h"
 #include "clk.h"
 
+#define PCG_PR_MASK		BIT(31)
 #define PCG_PCS_SHIFT	24
 #define PCG_PCS_MASK	0x7
 #define PCG_CGC_SHIFT	30
@@ -78,6 +79,10 @@ static struct clk_hw *imx_ulp_clk_hw_composite(const char *name,
 	struct clk_hw *hw;
 	u32 val;
 
+	val = readl(reg);
+	if (!(val & PCG_PR_MASK))
+		return ERR_PTR(-ENODEV);
+
 	if (mux_present) {
 		mux = kzalloc(sizeof(*mux), GFP_KERNEL);
 		if (!mux)

-- 
2.37.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 04/18] clk: imx: fracn-gppll: fix fractional part of PLL getting lost

[Peng Fan (OSS)]

From: Pengfei Li <pengfei.li_1@nxp.com>

Fractional part of PLL gets lost after re-enabling the PLL. the
MFN can NOT be automatically loaded when doing frac PLL enable/disable,
So when re-enable PLL, configure mfn explicitly.

Fixes: 1b26cb8a77a4 ("clk: imx: support fracn gppll")
Signed-off-by: Pengfei Li <pengfei.li_1@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
 drivers/clk/imx/clk-fracn-gppll.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/clk/imx/clk-fracn-gppll.c b/drivers/clk/imx/clk-fracn-gppll.c
index 44462ab50e51..1becba2b62d0 100644
--- a/drivers/clk/imx/clk-fracn-gppll.c
+++ b/drivers/clk/imx/clk-fracn-gppll.c
@@ -291,6 +291,10 @@ static int clk_fracn_gppll_prepare(struct clk_hw *hw)
 	if (val & POWERUP_MASK)
 		return 0;
 
+	if (pll->flags & CLK_FRACN_GPPLL_FRACN)
+		writel_relaxed(readl_relaxed(pll->base + PLL_NUMERATOR),
+			       pll->base + PLL_NUMERATOR);
+
 	val |= CLKMUX_BYPASS;
 	writel_relaxed(val, pll->base + PLL_CTRL);
 

-- 
2.37.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 05/18] clk: imx: pll14xx: Add constraint for fvco frequency

[Peng Fan (OSS)]

From: Shengjiu Wang <shengjiu.wang@nxp.com>

The fvco frequency range is between 1600MHz and 3200MHz, without
this constraint the fvco may out of range, the real output
frequency is no accurate.

Aslo correct the name for fvco and fout clock.

Fixes: b09c68dc57c9 ("clk: imx: pll14xx: Support dynamic rates")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Jacky Bai <ping.bai@nxp.com>
Tested-by: Chancel Liu <chancel.liu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
 drivers/clk/imx/clk-pll14xx.c | 8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)

diff --git a/drivers/clk/imx/clk-pll14xx.c b/drivers/clk/imx/clk-pll14xx.c
index d63564dbb12c..55812bfb9ec2 100644
--- a/drivers/clk/imx/clk-pll14xx.c
+++ b/drivers/clk/imx/clk-pll14xx.c
@@ -131,7 +131,7 @@ static void imx_pll14xx_calc_settings(struct clk_pll14xx *pll, unsigned long rat
 {
 	u32 pll_div_ctl0, pll_div_ctl1;
 	int mdiv, pdiv, sdiv, kdiv;
-	long fout, rate_min, rate_max, dist, best = LONG_MAX;
+	long fvco, fout, rate_min, rate_max, dist, best = LONG_MAX;
 	const struct imx_pll14xx_rate_table *tt;
 
 	/*
@@ -144,6 +144,8 @@ static void imx_pll14xx_calc_settings(struct clk_pll14xx *pll, unsigned long rat
 	 *
 	 * fvco = (m * 65536 + k) * prate / (p * 65536)
 	 * fout = (m * 65536 + k) * prate / (p * 65536) / (1 << sdiv)
+	 *
+	 * e) 1600MHz <= fvco <= 3200MHz
 	 */
 
 	/* First try if we can get the desired rate from one of the static entries */
@@ -193,6 +195,10 @@ static void imx_pll14xx_calc_settings(struct clk_pll14xx *pll, unsigned long rat
 			kdiv = pll1443x_calc_kdiv(mdiv, pdiv, sdiv, rate, prate);
 			fout = pll14xx_calc_rate(pll, mdiv, pdiv, sdiv, kdiv, prate);
 
+			fvco = fout << sdiv;
+
+			if (fvco < 1600000000 || fvco > 3200000000)
+				continue;
 			/* best match */
 			dist = abs((long)rate - (long)fout);
 			if (dist < best) {

-- 
2.37.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 06/18] clk: imx: pll14xx: use rate_table for audio plls

[Peng Fan (OSS)]

From: Shengjiu Wang <shengjiu.wang@nxp.com>

The generated clock frequency may not accurate, for example
the expected rate is 361267200U, but result is 361267199U.
Add rate_table for audio clocks to avoid such issue.

Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
 drivers/clk/imx/clk-pll14xx.c | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/drivers/clk/imx/clk-pll14xx.c b/drivers/clk/imx/clk-pll14xx.c
index 55812bfb9ec2..6b2c849f8b71 100644
--- a/drivers/clk/imx/clk-pll14xx.c
+++ b/drivers/clk/imx/clk-pll14xx.c
@@ -64,6 +64,17 @@ static const struct imx_pll14xx_rate_table imx_pll1443x_tbl[] = {
 	PLL_1443X_RATE(650000000U, 325, 3, 2, 0),
 	PLL_1443X_RATE(594000000U, 198, 2, 2, 0),
 	PLL_1443X_RATE(519750000U, 173, 2, 2, 16384),
+	PLL_1443X_RATE(393216000U, 262, 2, 3, 9437),
+	PLL_1443X_RATE(361267200U, 361, 3, 3, 17511),
+	PLL_1443X_RATE(245760000U, 328, 4, 3, 0xae15),
+	PLL_1443X_RATE(225792000U, 226, 3, 3, 0xcac1),
+	PLL_1443X_RATE(122880000U, 328, 4, 4, 0xae15),
+	PLL_1443X_RATE(112896000U, 226, 3, 4, 0xcac1),
+	PLL_1443X_RATE(61440000U, 328, 4, 5, 0xae15),
+	PLL_1443X_RATE(56448000U, 226, 3, 5, 0xcac1),
+	PLL_1443X_RATE(49152000U, 393, 3, 6, 0x374c),
+	PLL_1443X_RATE(45158400U, 241, 2, 6, 0xd845),
+	PLL_1443X_RATE(40960000U, 109, 1, 6, 0x3a07),
 };
 
 struct imx_pll14xx_clk imx_1443x_pll = {

-- 
2.37.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 06/18] clk: imx: pll14xx: use rate_table for audio plls

[Adam Ford]

On Fri, May 3, 2024 at 7:42 PM Peng Fan (OSS) <peng.fan@oss.nxp.com> wrote:
>
> From: Shengjiu Wang <shengjiu.wang@nxp.com>
>
> The generated clock frequency may not accurate, for example
> the expected rate is 361267200U, but result is 361267199U.
> Add rate_table for audio clocks to avoid such issue.

Wouldn't it be better to fix the clock calculator and eliminate the
look-up table completely?
The LUT seems like a work-around for a bug.

adam
>
> Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
> Reviewed-by: Jacky Bai <ping.bai@nxp.com>
> Signed-off-by: Peng Fan <peng.fan@nxp.com>
> ---
>  drivers/clk/imx/clk-pll14xx.c | 11 +++++++++++
>  1 file changed, 11 insertions(+)
>
> diff --git a/drivers/clk/imx/clk-pll14xx.c b/drivers/clk/imx/clk-pll14xx.c
> index 55812bfb9ec2..6b2c849f8b71 100644
> --- a/drivers/clk/imx/clk-pll14xx.c
> +++ b/drivers/clk/imx/clk-pll14xx.c
> @@ -64,6 +64,17 @@ static const struct imx_pll14xx_rate_table imx_pll1443x_tbl[] = {
>         PLL_1443X_RATE(650000000U, 325, 3, 2, 0),
>         PLL_1443X_RATE(594000000U, 198, 2, 2, 0),
>         PLL_1443X_RATE(519750000U, 173, 2, 2, 16384),
> +       PLL_1443X_RATE(393216000U, 262, 2, 3, 9437),
> +       PLL_1443X_RATE(361267200U, 361, 3, 3, 17511),
> +       PLL_1443X_RATE(245760000U, 328, 4, 3, 0xae15),
> +       PLL_1443X_RATE(225792000U, 226, 3, 3, 0xcac1),
> +       PLL_1443X_RATE(122880000U, 328, 4, 4, 0xae15),
> +       PLL_1443X_RATE(112896000U, 226, 3, 4, 0xcac1),
> +       PLL_1443X_RATE(61440000U, 328, 4, 5, 0xae15),
> +       PLL_1443X_RATE(56448000U, 226, 3, 5, 0xcac1),
> +       PLL_1443X_RATE(49152000U, 393, 3, 6, 0x374c),
> +       PLL_1443X_RATE(45158400U, 241, 2, 6, 0xd845),
> +       PLL_1443X_RATE(40960000U, 109, 1, 6, 0x3a07),
>  };
>
>  struct imx_pll14xx_clk imx_1443x_pll = {
>
> --
> 2.37.1
>
>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 07/18] clk: imx: pll14xx: potential integer overflow eliminated by casting to u64

[Peng Fan (OSS)]

From: Florin Pavelescu <florin.pavelescu@nxp.com>

Cast to u64, so that multiplications and additions will be done
in 64-bit arithmetic (and the results will also be 64-bit)
and the possibility of integer overflow is eliminated.

Fix Unintentional integer overflow reported by Coverity

Reviewed-by: Viorel Suman <viorel.suman@nxp.com>
Signed-off-by: Florin Pavelescu <florin.pavelescu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
 drivers/clk/imx/clk-pll14xx.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/clk/imx/clk-pll14xx.c b/drivers/clk/imx/clk-pll14xx.c
index 6b2c849f8b71..78eedb1f4a79 100644
--- a/drivers/clk/imx/clk-pll14xx.c
+++ b/drivers/clk/imx/clk-pll14xx.c
@@ -118,7 +118,7 @@ static long pll14xx_calc_rate(struct clk_pll14xx *pll, int mdiv, int pdiv,
 	u64 fout = prate;
 
 	/* fout = (m * 65536 + k) * Fin / (p * 65536) / (1 << sdiv) */
-	fout *= (mdiv * 65536 + kdiv);
+	fout *= ((u64)mdiv * 65536 + (u64)kdiv);
 	pdiv *= 65536;
 
 	do_div(fout, pdiv << sdiv);

-- 
2.37.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 07/18] clk: imx: pll14xx: potential integer overflow eliminated by casting to u64

[Francesco Dolcini]

Hello Peng,

On Sat, May 04, 2024 at 08:49:00AM +0800, Peng Fan (OSS) wrote:
> From: Florin Pavelescu <florin.pavelescu@nxp.com>
> 
> Cast to u64, so that multiplications and additions will be done
> in 64-bit arithmetic (and the results will also be 64-bit)
> and the possibility of integer overflow is eliminated.
> 
> Fix Unintentional integer overflow reported by Coverity

Fixes tag if this is a fix?

It would be interesting in general if this can be trigger in real life
and with which side effects or if we are just silencing the tool


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

RE: [PATCH 07/18] clk: imx: pll14xx: potential integer overflow eliminated by casting to u64

[Peng Fan]

> Subject: Re: [PATCH 07/18] clk: imx: pll14xx: potential integer overflow
> eliminated by casting to u64
> 
> Hello Peng,
> 
> On Sat, May 04, 2024 at 08:49:00AM +0800, Peng Fan (OSS) wrote:
> > From: Florin Pavelescu <florin.pavelescu@nxp.com>
> >
> > Cast to u64, so that multiplications and additions will be done in
> > 64-bit arithmetic (and the results will also be 64-bit) and the
> > possibility of integer overflow is eliminated.
> >
> > Fix Unintentional integer overflow reported by Coverity
> 
> Fixes tag if this is a fix?
> 
> It would be interesting in general if this can be trigger in real life and with
> which side effects or if we are just silencing the tool

This is just to silencing the tool, maybe this patch is no needed.

Thanks,
Peng.


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 08/18] clk: imx: imx8mp-audiomix: remove sdma root clock

[Peng Fan (OSS)]

From: Peng Fan <peng.fan@nxp.com>

There is an issue:
SDMA3 can't work without setting AUDIOMIX_CLKEN0[SDMA2] (bit-26) to 1

The workaround is:
As the reset state of AUDIOMIX_CLKEN0[SDMA2] is enabled,
we just need to keep it on as reset state, don't touch it
in kernel, then every thing is same as before, if we register
the clock in clk-audiomix, then kernel will try to disable
it in idle.

Reviewed-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
 drivers/clk/imx/clk-imx8mp-audiomix.c | 1 -
 1 file changed, 1 deletion(-)

diff --git a/drivers/clk/imx/clk-imx8mp-audiomix.c b/drivers/clk/imx/clk-imx8mp-audiomix.c
index b381d6f784c8..88d8ba975b5a 100644
--- a/drivers/clk/imx/clk-imx8mp-audiomix.c
+++ b/drivers/clk/imx/clk-imx8mp-audiomix.c
@@ -172,7 +172,6 @@ static struct clk_imx8mp_audiomix_sel sels[] = {
 	CLK_GATE("ocrama", OCRAMA_IPG),
 	CLK_GATE("aud2htx", AUD2HTX_IPG),
 	CLK_GATE("earc_phy", EARC_PHY),
-	CLK_GATE("sdma2", SDMA2_ROOT),
 	CLK_GATE("sdma3", SDMA3_ROOT),
 	CLK_GATE("spba2", SPBA2_ROOT),
 	CLK_GATE("dsp", DSP_ROOT),

-- 
2.37.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 08/18] clk: imx: imx8mp-audiomix: remove sdma root clock

[Francesco Dolcini]

Hello Peng,

On Sat, May 04, 2024 at 08:49:01AM +0800, Peng Fan (OSS) wrote:
> From: Peng Fan <peng.fan@nxp.com>
> 
> There is an issue:
> SDMA3 can't work without setting AUDIOMIX_CLKEN0[SDMA2] (bit-26) to 1

Fixes tag, given that this is fixing an issue?

Francesco


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

RE: [PATCH 08/18] clk: imx: imx8mp-audiomix: remove sdma root clock

[Peng Fan]

> Subject: Re: [PATCH 08/18] clk: imx: imx8mp-audiomix: remove sdma root
> clock
> 
> Hello Peng,
> 
> On Sat, May 04, 2024 at 08:49:01AM +0800, Peng Fan (OSS) wrote:
> > From: Peng Fan <peng.fan@nxp.com>
> >
> > There is an issue:
> > SDMA3 can't work without setting AUDIOMIX_CLKEN0[SDMA2] (bit-26) to
> 1
> 
> Fixes tag, given that this is fixing an issue?

Sure. will add the tag in v2.

Thanks,
Peng.
> 
> Francesco


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 09/18] clk: imx: imx8mp: fix clock tree update of TF-A managed clocks

[Peng Fan (OSS)]

From: Zhipeng Wang <zhipeng.wang_1@nxp.com>

On the i.MX8M*, the TF-A exposes a SiP (Silicon Provider) service
for DDR frequency scaling. The imx8m-ddrc-devfreq driver calls the
SiP and then does clk_set_parent on the DDR muxes to synchronize
the clock tree.

since commit 936c383673b9 ("clk: imx: fix composite peripheral flags"),
these TF-A managed muxes have SET_PARENT_GATE set, which results
in imx8m-ddrc-devfreq's clk_set_parent after SiP failing with -EBUSY:

clk_set_parent(dram_apb_src, sys1_pll_40m);(busfreq-imx8mq.c)

This is safe to do, because updating the Linux clock tree to reflect
reality will always be glitch-free.

commit 926bf91248dd
("clk: imx8m: fix clock tree update of TF-A managed clocks") adds this
method and enables 8mm, 8mn and 8mq. i.MX8MP also needs it.

Another reason to this patch is that powersave image BT music
requires dram to be 400MTS, so clk_set_parent(dram_alt_src,
sys1_pll_800m); is required. Without this patch, it will not succeed.

Fixes: 936c383673b9 ("clk: imx: fix composite peripheral flags")
Signed-off-by: Zhipeng Wang <zhipeng.wang_1@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
 drivers/clk/imx/clk-imx8mp.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/clk/imx/clk-imx8mp.c b/drivers/clk/imx/clk-imx8mp.c
index 670aa2bab301..e561ff7b135f 100644
--- a/drivers/clk/imx/clk-imx8mp.c
+++ b/drivers/clk/imx/clk-imx8mp.c
@@ -551,8 +551,8 @@ static int imx8mp_clocks_probe(struct platform_device *pdev)
 
 	hws[IMX8MP_CLK_IPG_ROOT] = imx_clk_hw_divider2("ipg_root", "ahb_root", ccm_base + 0x9080, 0, 1);
 
-	hws[IMX8MP_CLK_DRAM_ALT] = imx8m_clk_hw_composite("dram_alt", imx8mp_dram_alt_sels, ccm_base + 0xa000);
-	hws[IMX8MP_CLK_DRAM_APB] = imx8m_clk_hw_composite_critical("dram_apb", imx8mp_dram_apb_sels, ccm_base + 0xa080);
+	hws[IMX8MP_CLK_DRAM_ALT] = imx8m_clk_hw_fw_managed_composite("dram_alt", imx8mp_dram_alt_sels, ccm_base + 0xa000);
+	hws[IMX8MP_CLK_DRAM_APB] = imx8m_clk_hw_fw_managed_composite_critical("dram_apb", imx8mp_dram_apb_sels, ccm_base + 0xa080);
 	hws[IMX8MP_CLK_VPU_G1] = imx8m_clk_hw_composite("vpu_g1", imx8mp_vpu_g1_sels, ccm_base + 0xa100);
 	hws[IMX8MP_CLK_VPU_G2] = imx8m_clk_hw_composite("vpu_g2", imx8mp_vpu_g2_sels, ccm_base + 0xa180);
 	hws[IMX8MP_CLK_CAN1] = imx8m_clk_hw_composite("can1", imx8mp_can1_sels, ccm_base + 0xa200);

-- 
2.37.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 10/18] clk: imx: Remove CLK_SET_PARENT_GATE for DRAM mux for i.MX7D

[Peng Fan (OSS)]

From: Peng Fan <peng.fan@nxp.com>

For i.MX7D DRAM related mux clock, the clock source change should ONLY
be done done in low level asm code without accessing DRAM, and then
calling clk API to sync the HW clock status with clk tree, it should never
touch real clock source switch via clk API, so CLK_SET_PARENT_GATE flag
should NOT be added, otherwise, DRAM's clock parent will be disabled when
DRAM is active, and system will hang.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
 drivers/clk/imx/clk-imx7d.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/clk/imx/clk-imx7d.c b/drivers/clk/imx/clk-imx7d.c
index 2b77d1fc7bb9..1e1296e74835 100644
--- a/drivers/clk/imx/clk-imx7d.c
+++ b/drivers/clk/imx/clk-imx7d.c
@@ -498,9 +498,9 @@ static void __init imx7d_clocks_init(struct device_node *ccm_node)
 	hws[IMX7D_ENET_AXI_ROOT_SRC] = imx_clk_hw_mux2_flags("enet_axi_src", base + 0x8900, 24, 3, enet_axi_sel, ARRAY_SIZE(enet_axi_sel), CLK_SET_PARENT_GATE);
 	hws[IMX7D_NAND_USDHC_BUS_ROOT_SRC] = imx_clk_hw_mux2_flags("nand_usdhc_src", base + 0x8980, 24, 3, nand_usdhc_bus_sel, ARRAY_SIZE(nand_usdhc_bus_sel), CLK_SET_PARENT_GATE);
 	hws[IMX7D_DRAM_PHYM_ROOT_SRC] = imx_clk_hw_mux2_flags("dram_phym_src", base + 0x9800, 24, 1, dram_phym_sel, ARRAY_SIZE(dram_phym_sel), CLK_SET_PARENT_GATE);
-	hws[IMX7D_DRAM_ROOT_SRC] = imx_clk_hw_mux2_flags("dram_src", base + 0x9880, 24, 1, dram_sel, ARRAY_SIZE(dram_sel), CLK_SET_PARENT_GATE);
+	hws[IMX7D_DRAM_ROOT_SRC] = imx_clk_hw_mux2("dram_src", base + 0x9880, 24, 1, dram_sel, ARRAY_SIZE(dram_sel));
 	hws[IMX7D_DRAM_PHYM_ALT_ROOT_SRC] = imx_clk_hw_mux2_flags("dram_phym_alt_src", base + 0xa000, 24, 3, dram_phym_alt_sel, ARRAY_SIZE(dram_phym_alt_sel), CLK_SET_PARENT_GATE);
-	hws[IMX7D_DRAM_ALT_ROOT_SRC]  = imx_clk_hw_mux2_flags("dram_alt_src", base + 0xa080, 24, 3, dram_alt_sel, ARRAY_SIZE(dram_alt_sel), CLK_SET_PARENT_GATE);
+	hws[IMX7D_DRAM_ALT_ROOT_SRC]  = imx_clk_hw_mux2("dram_alt_src", base + 0xa080, 24, 3, dram_alt_sel, ARRAY_SIZE(dram_alt_sel));
 	hws[IMX7D_USB_HSIC_ROOT_SRC] = imx_clk_hw_mux2_flags("usb_hsic_src", base + 0xa100, 24, 3, usb_hsic_sel, ARRAY_SIZE(usb_hsic_sel), CLK_SET_PARENT_GATE);
 	hws[IMX7D_PCIE_CTRL_ROOT_SRC] = imx_clk_hw_mux2_flags("pcie_ctrl_src", base + 0xa180, 24, 3, pcie_ctrl_sel, ARRAY_SIZE(pcie_ctrl_sel), CLK_SET_PARENT_GATE);
 	hws[IMX7D_PCIE_PHY_ROOT_SRC] = imx_clk_hw_mux2_flags("pcie_phy_src", base + 0xa200, 24, 3, pcie_phy_sel, ARRAY_SIZE(pcie_phy_sel), CLK_SET_PARENT_GATE);

-- 
2.37.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 10/18] clk: imx: Remove CLK_SET_PARENT_GATE for DRAM mux for i.MX7D

[Francesco Dolcini]

Hello Peng,

On Sat, May 04, 2024 at 08:49:03AM +0800, Peng Fan (OSS) wrote:
> From: Peng Fan <peng.fan@nxp.com>
> 
> For i.MX7D DRAM related mux clock, the clock source change should ONLY
> be done done in low level asm code without accessing DRAM, and then
> calling clk API to sync the HW clock status with clk tree, it should never
> touch real clock source switch via clk API, so CLK_SET_PARENT_GATE flag
> should NOT be added, otherwise, DRAM's clock parent will be disabled when
> DRAM is active, and system will hang.

From the description this is solving a system hang, but no fixes tag nor
cc stable.

Francesco


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

RE: [PATCH 10/18] clk: imx: Remove CLK_SET_PARENT_GATE for DRAM mux for i.MX7D

[Peng Fan]

> Subject: Re: [PATCH 10/18] clk: imx: Remove CLK_SET_PARENT_GATE for
> DRAM mux for i.MX7D
> 
> Hello Peng,
> 
> On Sat, May 04, 2024 at 08:49:03AM +0800, Peng Fan (OSS) wrote:
> > From: Peng Fan <peng.fan@nxp.com>
> >
> > For i.MX7D DRAM related mux clock, the clock source change should ONLY
> > be done done in low level asm code without accessing DRAM, and then
> > calling clk API to sync the HW clock status with clk tree, it should
> > never touch real clock source switch via clk API, so
> > CLK_SET_PARENT_GATE flag should NOT be added, otherwise, DRAM's clock
> > parent will be disabled when DRAM is active, and system will hang.
> 
> From the description this is solving a system hang, but no fixes tag nor cc
> stable.

Not add fixes tab, because current upstream kernel not support DRAM freq
update for 7D, so the issue will not happen in upstream kernel. But in case
in future DRAM freq change needs change..
> 
> Francesco


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 11/18] clk: imx: add CLK_SET_RATE_PARENT for lcdif_pixel_src for i.MX7D

[Peng Fan (OSS)]

From: Peng Fan <peng.fan@nxp.com>

Add flag 'CLK_SET_RATE_PARENT' to 'IMX7D_LCDIF_PIXEL_ROOT_SRC' to
propagate rate changes from LCDIF pixel clock to video PLL to
provide more accurate clock rate for LCDIF pixel clock.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
 drivers/clk/imx/clk-imx7d.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/clk/imx/clk-imx7d.c b/drivers/clk/imx/clk-imx7d.c
index 1e1296e74835..99adc55e3f5d 100644
--- a/drivers/clk/imx/clk-imx7d.c
+++ b/drivers/clk/imx/clk-imx7d.c
@@ -505,7 +505,7 @@ static void __init imx7d_clocks_init(struct device_node *ccm_node)
 	hws[IMX7D_PCIE_CTRL_ROOT_SRC] = imx_clk_hw_mux2_flags("pcie_ctrl_src", base + 0xa180, 24, 3, pcie_ctrl_sel, ARRAY_SIZE(pcie_ctrl_sel), CLK_SET_PARENT_GATE);
 	hws[IMX7D_PCIE_PHY_ROOT_SRC] = imx_clk_hw_mux2_flags("pcie_phy_src", base + 0xa200, 24, 3, pcie_phy_sel, ARRAY_SIZE(pcie_phy_sel), CLK_SET_PARENT_GATE);
 	hws[IMX7D_EPDC_PIXEL_ROOT_SRC] = imx_clk_hw_mux2_flags("epdc_pixel_src", base + 0xa280, 24, 3, epdc_pixel_sel, ARRAY_SIZE(epdc_pixel_sel), CLK_SET_PARENT_GATE);
-	hws[IMX7D_LCDIF_PIXEL_ROOT_SRC] = imx_clk_hw_mux2_flags("lcdif_pixel_src", base + 0xa300, 24, 3, lcdif_pixel_sel, ARRAY_SIZE(lcdif_pixel_sel), CLK_SET_PARENT_GATE);
+	hws[IMX7D_LCDIF_PIXEL_ROOT_SRC] = imx_clk_hw_mux2_flags("lcdif_pixel_src", base + 0xa300, 24, 3, lcdif_pixel_sel, ARRAY_SIZE(lcdif_pixel_sel), CLK_SET_PARENT_GATE | CLK_SET_RATE_PARENT);
 	hws[IMX7D_MIPI_DSI_ROOT_SRC] = imx_clk_hw_mux2_flags("mipi_dsi_src", base + 0xa380, 24, 3,  mipi_dsi_sel, ARRAY_SIZE(mipi_dsi_sel), CLK_SET_PARENT_GATE);
 	hws[IMX7D_MIPI_CSI_ROOT_SRC] = imx_clk_hw_mux2_flags("mipi_csi_src", base + 0xa400, 24, 3, mipi_csi_sel, ARRAY_SIZE(mipi_csi_sel), CLK_SET_PARENT_GATE);
 	hws[IMX7D_MIPI_DPHY_ROOT_SRC] = imx_clk_hw_mux2_flags("mipi_dphy_src", base + 0xa480, 24, 3, mipi_dphy_sel, ARRAY_SIZE(mipi_dphy_sel), CLK_SET_PARENT_GATE);

-- 
2.37.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 12/18] clk: imx: imx8mn: add sai7_ipg_clk clock settings

[Peng Fan (OSS)]

From: Adrian Alonso <adrian.alonso@nxp.com>

Add IMX8MN_CLK_SAI7_IPG clock entry.

Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Adrian Alonso <adrian.alonso@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
 drivers/clk/imx/clk-imx8mn.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/clk/imx/clk-imx8mn.c b/drivers/clk/imx/clk-imx8mn.c
index 4bd1ed11353b..ab77e148e70c 100644
--- a/drivers/clk/imx/clk-imx8mn.c
+++ b/drivers/clk/imx/clk-imx8mn.c
@@ -583,6 +583,7 @@ static int imx8mn_clocks_probe(struct platform_device *pdev)
 	hws[IMX8MN_CLK_SDMA2_ROOT] = imx_clk_hw_gate4("sdma2_clk", "ipg_audio_root", base + 0x43b0, 0);
 	hws[IMX8MN_CLK_SDMA3_ROOT] = imx_clk_hw_gate4("sdma3_clk", "ipg_audio_root", base + 0x45f0, 0);
 	hws[IMX8MN_CLK_SAI7_ROOT] = imx_clk_hw_gate2_shared2("sai7_root_clk", "sai7", base + 0x4650, 0, &share_count_sai7);
+	hws[IMX8MN_CLK_SAI7_IPG] = imx_clk_hw_gate2_shared2("sai7_ipg_clk", "ipg_audio_root", base + 0x4650, 0, &share_count_sai7);
 
 	hws[IMX8MN_CLK_GPT_3M] = imx_clk_hw_fixed_factor("gpt_3m", "osc_24m", 1, 8);
 

-- 
2.37.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 13/18] clk: imx: imx8mm: Change the 'nand_usdhc_bus' clock to non-critical one

[Peng Fan (OSS)]

From: Jacky Bai <ping.bai@nxp.com>

The 'nand_usdhc_bus' clock is only need to be enabled when usdhc
or nand module is active, so change it to non-critical clock type.

Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
 drivers/clk/imx/clk-imx8mm.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/clk/imx/clk-imx8mm.c b/drivers/clk/imx/clk-imx8mm.c
index 075f643e3f35..342049b847b9 100644
--- a/drivers/clk/imx/clk-imx8mm.c
+++ b/drivers/clk/imx/clk-imx8mm.c
@@ -432,7 +432,7 @@ static int imx8mm_clocks_probe(struct platform_device *pdev)
 	/* BUS */
 	hws[IMX8MM_CLK_MAIN_AXI] = imx8m_clk_hw_composite_bus_critical("main_axi",  imx8mm_main_axi_sels, base + 0x8800);
 	hws[IMX8MM_CLK_ENET_AXI] = imx8m_clk_hw_composite_bus("enet_axi", imx8mm_enet_axi_sels, base + 0x8880);
-	hws[IMX8MM_CLK_NAND_USDHC_BUS] = imx8m_clk_hw_composite_bus_critical("nand_usdhc_bus", imx8mm_nand_usdhc_sels, base + 0x8900);
+	hws[IMX8MM_CLK_NAND_USDHC_BUS] = imx8m_clk_hw_composite("nand_usdhc_bus", imx8mm_nand_usdhc_sels, base + 0x8900);
 	hws[IMX8MM_CLK_VPU_BUS] = imx8m_clk_hw_composite_bus("vpu_bus", imx8mm_vpu_bus_sels, base + 0x8980);
 	hws[IMX8MM_CLK_DISP_AXI] = imx8m_clk_hw_composite_bus("disp_axi", imx8mm_disp_axi_sels, base + 0x8a00);
 	hws[IMX8MM_CLK_DISP_APB] = imx8m_clk_hw_composite_bus("disp_apb", imx8mm_disp_apb_sels, base + 0x8a80);

-- 
2.37.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 14/18] clk: imx: imx8qxp: Add LVDS bypass clocks

[Peng Fan (OSS)]

From: Peng Fan <peng.fan@nxp.com>

For iMX8QXP and iMX8QM, add bypass clocks and register some of the LVDS
clocks with imx_clk_scu2 as the parent needs to explicitly set.

In order to make sure MIPI DSI works well after suspend/resume, the LVDS
pixel and phy clocks must be initialized before the MIPI tx_esacpe
and rx_escape clocks. LVDS phy, LVDS pixel, tx_escape, and rx_esacpe are all
on the same MSLICE. They all share the same clock parent. So, setting the
parent source or rate affects all of these clocks. In the LVDS use case the
MIPI tx_escape and rx_escape are not saved and restored. So, LVDS works for
either clock initialization order. For MIPI case, LVDS must be initialized first.

Signed-off-by: Ranjani Vaidyanathan <ranjani.vaidyanathan@nxp.com>
Signed-off-by: Oliver F. Brown <oliver.brown@oss.nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
 drivers/clk/imx/clk-imx8qxp.c | 17 ++++++++---------
 1 file changed, 8 insertions(+), 9 deletions(-)

diff --git a/drivers/clk/imx/clk-imx8qxp.c b/drivers/clk/imx/clk-imx8qxp.c
index 7d8883916cac..a0654edaae83 100644
--- a/drivers/clk/imx/clk-imx8qxp.c
+++ b/drivers/clk/imx/clk-imx8qxp.c
@@ -71,7 +71,7 @@ static const char *const lvds0_sels[] = {
 	"clk_dummy",
 	"clk_dummy",
 	"clk_dummy",
-	"mipi0_lvds_bypass_clk",
+	"lvds0_bypass_clk",
 };
 
 static const char *const lvds1_sels[] = {
@@ -79,7 +79,7 @@ static const char *const lvds1_sels[] = {
 	"clk_dummy",
 	"clk_dummy",
 	"clk_dummy",
-	"mipi1_lvds_bypass_clk",
+	"lvds1_bypass_clk",
 };
 
 static const char * const mipi_sels[] = {
@@ -223,9 +223,9 @@ static int imx8qxp_clk_probe(struct platform_device *pdev)
 	/* MIPI-LVDS SS */
 	imx_clk_scu("mipi0_bypass_clk", IMX_SC_R_MIPI_0, IMX_SC_PM_CLK_BYPASS);
 	imx_clk_scu("mipi0_pixel_clk", IMX_SC_R_MIPI_0, IMX_SC_PM_CLK_PER);
-	imx_clk_scu("mipi0_lvds_bypass_clk", IMX_SC_R_LVDS_0, IMX_SC_PM_CLK_BYPASS);
-	imx_clk_scu2("mipi0_lvds_pixel_clk", lvds0_sels, ARRAY_SIZE(lvds0_sels), IMX_SC_R_LVDS_0, IMX_SC_PM_CLK_MISC2);
-	imx_clk_scu2("mipi0_lvds_phy_clk", lvds0_sels, ARRAY_SIZE(lvds0_sels), IMX_SC_R_LVDS_0, IMX_SC_PM_CLK_MISC3);
+	imx_clk_scu("lvds0_bypass_clk", IMX_SC_R_LVDS_0, IMX_SC_PM_CLK_BYPASS);
+	imx_clk_scu2("lvds0_pixel_clk", lvds0_sels, ARRAY_SIZE(lvds0_sels), IMX_SC_R_LVDS_0, IMX_SC_PM_CLK_MISC2);
+	imx_clk_scu2("lvds0_phy_clk", lvds0_sels, ARRAY_SIZE(lvds0_sels), IMX_SC_R_LVDS_0, IMX_SC_PM_CLK_MISC3);
 	imx_clk_scu2("mipi0_dsi_tx_esc_clk", mipi_sels, ARRAY_SIZE(mipi_sels), IMX_SC_R_MIPI_0, IMX_SC_PM_CLK_MST_BUS);
 	imx_clk_scu2("mipi0_dsi_rx_esc_clk", mipi_sels, ARRAY_SIZE(mipi_sels), IMX_SC_R_MIPI_0, IMX_SC_PM_CLK_SLV_BUS);
 	imx_clk_scu2("mipi0_dsi_phy_clk", mipi_sels, ARRAY_SIZE(mipi_sels), IMX_SC_R_MIPI_0, IMX_SC_PM_CLK_PHY);
@@ -235,10 +235,9 @@ static int imx8qxp_clk_probe(struct platform_device *pdev)
 
 	imx_clk_scu("mipi1_bypass_clk", IMX_SC_R_MIPI_1, IMX_SC_PM_CLK_BYPASS);
 	imx_clk_scu("mipi1_pixel_clk", IMX_SC_R_MIPI_1, IMX_SC_PM_CLK_PER);
-	imx_clk_scu("mipi1_lvds_bypass_clk", IMX_SC_R_LVDS_1, IMX_SC_PM_CLK_BYPASS);
-	imx_clk_scu2("mipi1_lvds_pixel_clk", lvds1_sels, ARRAY_SIZE(lvds1_sels), IMX_SC_R_LVDS_1, IMX_SC_PM_CLK_MISC2);
-	imx_clk_scu2("mipi1_lvds_phy_clk", lvds1_sels, ARRAY_SIZE(lvds1_sels), IMX_SC_R_LVDS_1, IMX_SC_PM_CLK_MISC3);
-
+	imx_clk_scu("lvds1_bypass_clk", IMX_SC_R_LVDS_1, IMX_SC_PM_CLK_BYPASS);
+	imx_clk_scu2("lvds1_pixel_clk", lvds1_sels, ARRAY_SIZE(lvds1_sels), IMX_SC_R_LVDS_1, IMX_SC_PM_CLK_MISC2);
+	imx_clk_scu2("lvds1_phy_clk", lvds1_sels, ARRAY_SIZE(lvds1_sels), IMX_SC_R_LVDS_1, IMX_SC_PM_CLK_MISC3);
 	imx_clk_scu2("mipi1_dsi_tx_esc_clk", mipi_sels, ARRAY_SIZE(mipi_sels), IMX_SC_R_MIPI_1, IMX_SC_PM_CLK_MST_BUS);
 	imx_clk_scu2("mipi1_dsi_rx_esc_clk", mipi_sels, ARRAY_SIZE(mipi_sels), IMX_SC_R_MIPI_1, IMX_SC_PM_CLK_SLV_BUS);
 	imx_clk_scu2("mipi1_dsi_phy_clk", mipi_sels, ARRAY_SIZE(mipi_sels), IMX_SC_R_MIPI_1, IMX_SC_PM_CLK_PHY);

-- 
2.37.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 15/18] clk: imx: imx8qxp: Add clock muxes for MIPI and PHY ref clocks

[Peng Fan (OSS)]

From: "Oliver F. Brown" <oliver.brown@oss.nxp.com>

The MIPI Pixel and PHY Reference can use the bypass clock as a source. The
MIPI bypass clock is the Pixel clock from the Display controller via the
pixel link. Using the pixel clock for the PHY reference allows the MIPI bit
clock match the pixel rate exactly.

The MIPI pixel clock is currently set to be source from the bypass clock in
the SCFW. This patch allows the pixel clock parent to be set by the kernel
in the event that the SCFW default clock parent may change in the future.

Signed-off-by: Oliver F. Brown <oliver.brown@oss.nxp.com>
Signed-off-by: Robert Chiras <robert.chiras@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
 drivers/clk/imx/clk-imx8qxp.c | 24 ++++++++++++++++++++----
 1 file changed, 20 insertions(+), 4 deletions(-)

diff --git a/drivers/clk/imx/clk-imx8qxp.c b/drivers/clk/imx/clk-imx8qxp.c
index a0654edaae83..fe6509be6ce9 100644
--- a/drivers/clk/imx/clk-imx8qxp.c
+++ b/drivers/clk/imx/clk-imx8qxp.c
@@ -90,6 +90,22 @@ static const char * const mipi_sels[] = {
 	"clk_dummy",
 };
 
+static const char * const mipi0_phy_sels[] = {
+	"clk_dummy",
+	"clk_dummy",
+	"mipi_pll_div2_clk",
+	"clk_dummy",
+	"mipi0_bypass_clk",
+};
+
+static const char * const mipi1_phy_sels[] = {
+	"clk_dummy",
+	"clk_dummy",
+	"mipi_pll_div2_clk",
+	"clk_dummy",
+	"mipi1_bypass_clk",
+};
+
 static const char * const lcd_sels[] = {
 	"clk_dummy",
 	"clk_dummy",
@@ -222,25 +238,25 @@ static int imx8qxp_clk_probe(struct platform_device *pdev)
 
 	/* MIPI-LVDS SS */
 	imx_clk_scu("mipi0_bypass_clk", IMX_SC_R_MIPI_0, IMX_SC_PM_CLK_BYPASS);
-	imx_clk_scu("mipi0_pixel_clk", IMX_SC_R_MIPI_0, IMX_SC_PM_CLK_PER);
+	imx_clk_scu2("mipi0_pixel_clk", mipi0_phy_sels, ARRAY_SIZE(mipi0_phy_sels), IMX_SC_R_MIPI_0, IMX_SC_PM_CLK_PER);
 	imx_clk_scu("lvds0_bypass_clk", IMX_SC_R_LVDS_0, IMX_SC_PM_CLK_BYPASS);
 	imx_clk_scu2("lvds0_pixel_clk", lvds0_sels, ARRAY_SIZE(lvds0_sels), IMX_SC_R_LVDS_0, IMX_SC_PM_CLK_MISC2);
 	imx_clk_scu2("lvds0_phy_clk", lvds0_sels, ARRAY_SIZE(lvds0_sels), IMX_SC_R_LVDS_0, IMX_SC_PM_CLK_MISC3);
 	imx_clk_scu2("mipi0_dsi_tx_esc_clk", mipi_sels, ARRAY_SIZE(mipi_sels), IMX_SC_R_MIPI_0, IMX_SC_PM_CLK_MST_BUS);
 	imx_clk_scu2("mipi0_dsi_rx_esc_clk", mipi_sels, ARRAY_SIZE(mipi_sels), IMX_SC_R_MIPI_0, IMX_SC_PM_CLK_SLV_BUS);
-	imx_clk_scu2("mipi0_dsi_phy_clk", mipi_sels, ARRAY_SIZE(mipi_sels), IMX_SC_R_MIPI_0, IMX_SC_PM_CLK_PHY);
+	imx_clk_scu2("mipi0_dsi_phy_clk", mipi0_phy_sels, ARRAY_SIZE(mipi0_phy_sels), IMX_SC_R_MIPI_0, IMX_SC_PM_CLK_PHY);
 	imx_clk_scu("mipi0_i2c0_clk", IMX_SC_R_MIPI_0_I2C_0, IMX_SC_PM_CLK_MISC2);
 	imx_clk_scu("mipi0_i2c1_clk", IMX_SC_R_MIPI_0_I2C_1, IMX_SC_PM_CLK_MISC2);
 	imx_clk_scu("mipi0_pwm0_clk", IMX_SC_R_MIPI_0_PWM_0, IMX_SC_PM_CLK_PER);
 
 	imx_clk_scu("mipi1_bypass_clk", IMX_SC_R_MIPI_1, IMX_SC_PM_CLK_BYPASS);
-	imx_clk_scu("mipi1_pixel_clk", IMX_SC_R_MIPI_1, IMX_SC_PM_CLK_PER);
+	imx_clk_scu2("mipi1_pixel_clk", mipi1_phy_sels, ARRAY_SIZE(mipi1_phy_sels), IMX_SC_R_MIPI_1, IMX_SC_PM_CLK_PER);
 	imx_clk_scu("lvds1_bypass_clk", IMX_SC_R_LVDS_1, IMX_SC_PM_CLK_BYPASS);
 	imx_clk_scu2("lvds1_pixel_clk", lvds1_sels, ARRAY_SIZE(lvds1_sels), IMX_SC_R_LVDS_1, IMX_SC_PM_CLK_MISC2);
 	imx_clk_scu2("lvds1_phy_clk", lvds1_sels, ARRAY_SIZE(lvds1_sels), IMX_SC_R_LVDS_1, IMX_SC_PM_CLK_MISC3);
 	imx_clk_scu2("mipi1_dsi_tx_esc_clk", mipi_sels, ARRAY_SIZE(mipi_sels), IMX_SC_R_MIPI_1, IMX_SC_PM_CLK_MST_BUS);
 	imx_clk_scu2("mipi1_dsi_rx_esc_clk", mipi_sels, ARRAY_SIZE(mipi_sels), IMX_SC_R_MIPI_1, IMX_SC_PM_CLK_SLV_BUS);
-	imx_clk_scu2("mipi1_dsi_phy_clk", mipi_sels, ARRAY_SIZE(mipi_sels), IMX_SC_R_MIPI_1, IMX_SC_PM_CLK_PHY);
+	imx_clk_scu2("mipi1_dsi_phy_clk", mipi1_phy_sels, ARRAY_SIZE(mipi1_phy_sels), IMX_SC_R_MIPI_1, IMX_SC_PM_CLK_PHY);
 	imx_clk_scu("mipi1_i2c0_clk", IMX_SC_R_MIPI_1_I2C_0, IMX_SC_PM_CLK_MISC2);
 	imx_clk_scu("mipi1_i2c1_clk", IMX_SC_R_MIPI_1_I2C_1, IMX_SC_PM_CLK_MISC2);
 	imx_clk_scu("mipi1_pwm0_clk", IMX_SC_R_MIPI_1_PWM_0, IMX_SC_PM_CLK_PER);

-- 
2.37.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 16/18] clk: imx: imx8qxp: Register dc0_bypass0_clk before disp clk

[Peng Fan (OSS)]

From: Peng Fan <peng.fan@nxp.com>

The initialization order of SCU clocks affects the sequence of SCU clock
resume. If there are no other effects, the earlier the initialization,
the earlier the resume. During SCU clock resume, the clock rate is
restored. As SCFW guidelines, configure the parent clock rate before
configuring the child rate.

Fixes: 91e916771de0 ("clk: imx: scu: remove legacy scu clock binding support")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
 drivers/clk/imx/clk-imx8qxp.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/clk/imx/clk-imx8qxp.c b/drivers/clk/imx/clk-imx8qxp.c
index fe6509be6ce9..47f4ceab1179 100644
--- a/drivers/clk/imx/clk-imx8qxp.c
+++ b/drivers/clk/imx/clk-imx8qxp.c
@@ -222,11 +222,11 @@ static int imx8qxp_clk_probe(struct platform_device *pdev)
 	imx_clk_scu("usb3_lpm_div", IMX_SC_R_USB_2, IMX_SC_PM_CLK_MISC);
 
 	/* Display controller SS */
-	imx_clk_scu2("dc0_disp0_clk", dc0_sels, ARRAY_SIZE(dc0_sels), IMX_SC_R_DC_0, IMX_SC_PM_CLK_MISC0);
-	imx_clk_scu2("dc0_disp1_clk", dc0_sels, ARRAY_SIZE(dc0_sels), IMX_SC_R_DC_0, IMX_SC_PM_CLK_MISC1);
 	imx_clk_scu("dc0_pll0_clk", IMX_SC_R_DC_0_PLL_0, IMX_SC_PM_CLK_PLL);
 	imx_clk_scu("dc0_pll1_clk", IMX_SC_R_DC_0_PLL_1, IMX_SC_PM_CLK_PLL);
 	imx_clk_scu("dc0_bypass0_clk", IMX_SC_R_DC_0_VIDEO0, IMX_SC_PM_CLK_BYPASS);
+	imx_clk_scu2("dc0_disp0_clk", dc0_sels, ARRAY_SIZE(dc0_sels), IMX_SC_R_DC_0, IMX_SC_PM_CLK_MISC0);
+	imx_clk_scu2("dc0_disp1_clk", dc0_sels, ARRAY_SIZE(dc0_sels), IMX_SC_R_DC_0, IMX_SC_PM_CLK_MISC1);
 	imx_clk_scu("dc0_bypass1_clk", IMX_SC_R_DC_0_VIDEO1, IMX_SC_PM_CLK_BYPASS);
 
 	imx_clk_scu2("dc1_disp0_clk", dc1_sels, ARRAY_SIZE(dc1_sels), IMX_SC_R_DC_1, IMX_SC_PM_CLK_MISC0);

-- 
2.37.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 17/18] clk: imx: imx8qxp: Parent should be initialized earlier than the clock

[Peng Fan (OSS)]

From: Peng Fan <peng.fan@nxp.com>

The initialization order of SCU clocks affects the sequence of SCU clock
resume. If there are no other effects, the earlier the initialization,
the earlier the resume. During SCU clock resume, the clock rate is
restored. As SCFW guidelines, configure the parent clock rate before
configuring the child rate.

Fixes: babfaa9556d7 ("clk: imx: scu: add more scu clocks")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
 drivers/clk/imx/clk-imx8qxp.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/clk/imx/clk-imx8qxp.c b/drivers/clk/imx/clk-imx8qxp.c
index 47f4ceab1179..3ae162625bb1 100644
--- a/drivers/clk/imx/clk-imx8qxp.c
+++ b/drivers/clk/imx/clk-imx8qxp.c
@@ -186,8 +186,8 @@ static int imx8qxp_clk_probe(struct platform_device *pdev)
 	imx_clk_scu("pwm_clk",   IMX_SC_R_LCD_0_PWM_0, IMX_SC_PM_CLK_PER);
 	imx_clk_scu("elcdif_pll", IMX_SC_R_ELCDIF_PLL, IMX_SC_PM_CLK_PLL);
 	imx_clk_scu2("lcd_clk", lcd_sels, ARRAY_SIZE(lcd_sels), IMX_SC_R_LCD_0, IMX_SC_PM_CLK_PER);
-	imx_clk_scu2("lcd_pxl_clk", lcd_pxl_sels, ARRAY_SIZE(lcd_pxl_sels), IMX_SC_R_LCD_0, IMX_SC_PM_CLK_MISC0);
 	imx_clk_scu("lcd_pxl_bypass_div_clk", IMX_SC_R_LCD_0, IMX_SC_PM_CLK_BYPASS);
+	imx_clk_scu2("lcd_pxl_clk", lcd_pxl_sels, ARRAY_SIZE(lcd_pxl_sels), IMX_SC_R_LCD_0, IMX_SC_PM_CLK_MISC0);
 
 	/* Audio SS */
 	imx_clk_scu("audio_pll0_clk", IMX_SC_R_AUDIO_PLL_0, IMX_SC_PM_CLK_PLL);
@@ -229,11 +229,11 @@ static int imx8qxp_clk_probe(struct platform_device *pdev)
 	imx_clk_scu2("dc0_disp1_clk", dc0_sels, ARRAY_SIZE(dc0_sels), IMX_SC_R_DC_0, IMX_SC_PM_CLK_MISC1);
 	imx_clk_scu("dc0_bypass1_clk", IMX_SC_R_DC_0_VIDEO1, IMX_SC_PM_CLK_BYPASS);
 
-	imx_clk_scu2("dc1_disp0_clk", dc1_sels, ARRAY_SIZE(dc1_sels), IMX_SC_R_DC_1, IMX_SC_PM_CLK_MISC0);
-	imx_clk_scu2("dc1_disp1_clk", dc1_sels, ARRAY_SIZE(dc1_sels), IMX_SC_R_DC_1, IMX_SC_PM_CLK_MISC1);
 	imx_clk_scu("dc1_pll0_clk", IMX_SC_R_DC_1_PLL_0, IMX_SC_PM_CLK_PLL);
 	imx_clk_scu("dc1_pll1_clk", IMX_SC_R_DC_1_PLL_1, IMX_SC_PM_CLK_PLL);
 	imx_clk_scu("dc1_bypass0_clk", IMX_SC_R_DC_1_VIDEO0, IMX_SC_PM_CLK_BYPASS);
+	imx_clk_scu2("dc1_disp0_clk", dc1_sels, ARRAY_SIZE(dc1_sels), IMX_SC_R_DC_1, IMX_SC_PM_CLK_MISC0);
+	imx_clk_scu2("dc1_disp1_clk", dc1_sels, ARRAY_SIZE(dc1_sels), IMX_SC_R_DC_1, IMX_SC_PM_CLK_MISC1);
 	imx_clk_scu("dc1_bypass1_clk", IMX_SC_R_DC_1_VIDEO1, IMX_SC_PM_CLK_BYPASS);
 
 	/* MIPI-LVDS SS */

-- 
2.37.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 18/18] clk: imx: fracn-gppll: update rate table

[Peng Fan (OSS)]

From: Peng Fan <peng.fan@nxp.com>

- Add 1039.5MHz clock for video PLL to fulfill the LVDS display
  148.5MHz * 7 requirement
- Add 800MHz clock for ARM PLL

Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
 drivers/clk/imx/clk-fracn-gppll.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/clk/imx/clk-fracn-gppll.c b/drivers/clk/imx/clk-fracn-gppll.c
index 1becba2b62d0..591e0364ee5c 100644
--- a/drivers/clk/imx/clk-fracn-gppll.c
+++ b/drivers/clk/imx/clk-fracn-gppll.c
@@ -78,6 +78,7 @@ struct clk_fracn_gppll {
  * The Fvco should be in range 2.5Ghz to 5Ghz
  */
 static const struct imx_fracn_gppll_rate_table fracn_tbl[] = {
+	PLL_FRACN_GP(1039500000U, 173, 25, 100, 1, 4),
 	PLL_FRACN_GP(650000000U, 162, 50, 100, 0, 6),
 	PLL_FRACN_GP(594000000U, 198, 0, 1, 0, 8),
 	PLL_FRACN_GP(560000000U, 140, 0, 1, 0, 6),
@@ -106,6 +107,7 @@ static const struct imx_fracn_gppll_rate_table int_tbl[] = {
 	PLL_FRACN_GP_INTEGER(1700000000U, 141, 1, 2),
 	PLL_FRACN_GP_INTEGER(1400000000U, 175, 1, 3),
 	PLL_FRACN_GP_INTEGER(900000000U, 150, 1, 4),
+	PLL_FRACN_GP_INTEGER(800000000U, 200, 1, 6),
 };
 
 struct imx_fracn_gppll_clk imx_fracn_gppll_integer = {

-- 
2.37.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel