[PATCH v3 0/2] Introduce basic support for MR-NAVQ95

[PATCH v3 0/2] Introduce basic support for MR-NAVQ95

[Laurentiu Mihalcea]

From: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>

Hi folks,

So, as the title says, this series attempts to introduce basic support for
NXP's MR-NAVQ95 board. The "basic support" refers to introducing a new DTS
and enabling a couple of peripherals so that the board'll be able to boot
from eMMC/SD/NFS.

So, compared to MX95-19x19-EVK, this board has a smaller form factor
(comparable to the MX95-based FRDM boards) and is designed for
robotics-related applications (e.g. drones, rovers, humanoids, etc...).
The board is currently at revision B and is only available internally.
The board should be officially announced around October/November 2026.

Given that the board and its support are fairly new and still under
development, I would expect some (hopefully) small changes to the DTS.
Hopefully, this'll be acceptable.

The schematics, a brief overview and some pictures of the board are
publicly available at [1].

[1]: https://github.com/NXP-Robotics/MR-NAVQ95

---

Changes in v3:

* use "gpios" instead of the deprecated "gpio" for the "regulator-usdhc2"
node.

* fix issues raised by running "dt-check-style --mode strict". Note that
"dt-check-style" still reports the following issues:

[property-order] property 'compatible' out of canonical order [...]
[line-length] line exceeds 80 columns [...]

these'll be fixed by Krzysztof Kozlowski's on-going patches: [3]. Manually
applied his patches and dt-check-style seems happy with the DTS.

* link to v2: https://lore.kernel.org/imx/20260827150657.1657-1-laurentiumihalcea111@gmail.com/

[3]: https://lore.kernel.org/lkml/20260826-n-dts-style-checker-continued-v5-0-fdd16ca6e771@oss.qualcomm.com/

Changes in v2:

* remove the "pinctrl_usdhc2_100mhz", "pinctrl_usdhc2_200mhz", and
"pinctrl_usdhc1_100mhz" DT nodes as they have the same configuration
as "pinctrl_usdhc2" and "pinctrl_usdhc1", respectively.

* add "bootph-pre-ram" property to all nodes that were included in Elena's
u-boot patches. See [2]. Note that "imx95-u-boot.dtsi" is still required
for the binman node and for the rest of the nodes tagged with
"bootph-pre-ram".

* link to v1: https://lore.kernel.org/imx/20260825120812.2152-1-laurentiumihalcea111@gmail.com/

[2]: https://lists.u-boot-project.org/pipermail/u-boot/2026-August/629002.html

---

Laurentiu Mihalcea (2):
  dt-bindings: arm: fsl: add MR-NAVQ95 board
  arm64: dts: freescale: add MR-NAVQ95 basic board support

 .../devicetree/bindings/arm/fsl.yaml          |   1 +
 arch/arm64/boot/dts/freescale/Makefile        |   1 +
 arch/arm64/boot/dts/freescale/imx95-navq.dts  | 222 ++++++++++++++++++
 3 files changed, 224 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx95-navq.dts

-- 
2.53.0

[PATCH v3 1/2] dt-bindings: arm: fsl: add MR-NAVQ95 board

[Laurentiu Mihalcea]

From: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>

Add DT compatible string for the MR-NAVQ95 board.

Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
---
 Documentation/devicetree/bindings/arm/fsl.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 656f2596e1d5..5d9da745b715 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -1535,6 +1535,7 @@ properties:
               - fsl,imx95-15x15-frdm      # i.MX95 15x15 FRDM Board
               - fsl,imx95-19x19-evk       # i.MX95 19x19 EVK Board
               - fsl,imx95-19x19-frdm-pro  # i.MX95 19x19 FRDM PRO Board
+              - fsl,imx95-navq            # MR-NAVQ95 board
               - toradex,verdin-imx95-19x19-evk  # i.MX95 Verdin Evaluation Kit (EVK)
           - const: fsl,imx95
 
-- 
2.53.0

[PATCH v3 2/2] arm64: dts: freescale: add MR-NAVQ95 basic board support

[Laurentiu Mihalcea]

From: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>

Add basic support for NXP's MR-NAVQ95 board. This board is designed for
robotics applications (e.g. drones, rovers, humanoids, etc..) and has the
following hardware feats (list is not exhaustive):

* based on i.MX95 19x19 SoC
* 64GB eMMC
* up to 16GB of LPDDR5 memory
* 1 x USB 2.0 TypeC
* 1 x USB 3.0 TypeC
* 1 x RJ45 port with RTL8211 PHY

The support targets revision B of the board.

Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
---
 arch/arm64/boot/dts/freescale/Makefile       |   1 +
 arch/arm64/boot/dts/freescale/imx95-navq.dts | 222 +++++++++++++++++++
 2 files changed, 223 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx95-navq.dts

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 95ae85ab4adf..4c5ef83cd857 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -712,6 +712,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx95-19x19-evk-sof.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx95-19x19-frdm-pro.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx95-aquila-clover.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx95-aquila-dev.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx95-navq.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx95-toradex-smarc-dev.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx95-tqma9596la-mba95xxca.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx95-tqma9596sa-mb-smarc-2.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx95-navq.dts b/arch/arm64/boot/dts/freescale/imx95-navq.dts
new file mode 100644
index 000000000000..1366dc2d2bfa
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx95-navq.dts
@@ -0,0 +1,222 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2026 NXP
+ */
+
+/dts-v1/;
+
+#include "imx95.dtsi"
+
+/ {
+	model = "NXP MR-NAVQ95";
+	compatible = "fsl,imx95-navq", "fsl,imx95";
+
+	aliases {
+		ethernet0 = &enetc_port0;
+		mmc0 = &usdhc1;
+		mmc1 = &usdhc2;
+		serial0 = &lpuart1;
+	};
+
+	chosen {
+		stdout-path = &lpuart1;
+	};
+
+	reg_usdhc2_vmmc: regulator-usdhc2 {
+		compatible = "regulator-fixed";
+		bootph-pre-ram;
+		enable-active-high;
+		gpios = <&gpio3 7 GPIO_ACTIVE_HIGH>;
+		off-on-delay-us = <12000>;
+		pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
+		pinctrl-names = "default";
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "VDD_SD2_3V3";
+	};
+};
+
+&edma1 {
+	/* owned by M7 */
+	status = "reserved";
+};
+
+&edma2 {
+	/* channels 30-63 owned by M7 */
+	dma-channels = <30>;
+};
+
+&enetc_port0 {
+	phy-handle = <&ethphy0>;
+	phy-mode = "rgmii-id";
+	pinctrl-0 = <&pinctrl_enetc0>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&lpi2c3 {
+	clock-frequency = <400000>;
+	pinctrl-0 = <&pinctrl_lpi2c3>;
+	pinctrl-names = "default";
+
+	status = "okay";
+
+	i2c3_gpio_expander_21: gpio-expander@21 {
+		compatible = "nxp,pcal6408";
+		reg = <0x21>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		#interrupt-cells = <2>;
+		interrupt-controller;
+		interrupt-parent = <&gpio4>;
+		interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-0 = <&pinctrl_i2c3_gpio_expander_21>;
+		pinctrl-names = "default";
+	};
+};
+
+&lpuart1 {
+	bootph-pre-ram;
+	pinctrl-0 = <&pinctrl_uart1>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&netc_blk_ctrl {
+	status = "okay";
+};
+
+&netc_emdio {
+	pinctrl-0 = <&pinctrl_emdio>;
+	pinctrl-names = "default";
+
+	status = "okay";
+
+	ethphy0: ethernet-phy@1 {
+		compatible = "ethernet-phy-id001c.c916";
+		reg = <1>;
+		reset-assert-us = <10000>;
+		reset-deassert-us = <80000>;
+		reset-gpios = <&i2c3_gpio_expander_21 1 GPIO_ACTIVE_LOW>;
+		realtek,clkout-disable;
+	};
+};
+
+&scmi_iomuxc {
+	pinctrl_emdio: emdiogrp {
+		fsl,pins = <IMX95_PAD_ENET2_MDC__NETCMIX_TOP_NETC_MDC			0x57e>,
+			   <IMX95_PAD_ENET2_MDIO__NETCMIX_TOP_NETC_MDIO			0x97e>;
+	};
+
+	pinctrl_enetc0: enetc0grp {
+		fsl,pins = <IMX95_PAD_ENET1_TD3__NETCMIX_TOP_ETH0_RGMII_TD3		0x57e>,
+			   <IMX95_PAD_ENET1_TD2__NETCMIX_TOP_ETH0_RGMII_TD2		0x57e>,
+			   <IMX95_PAD_ENET1_TD1__NETCMIX_TOP_ETH0_RGMII_TD1		0x57e>,
+			   <IMX95_PAD_ENET1_TD0__NETCMIX_TOP_ETH0_RGMII_TD0		0x57e>,
+			   <IMX95_PAD_ENET1_TX_CTL__NETCMIX_TOP_ETH0_RGMII_TX_CTL	0x57e>,
+			   <IMX95_PAD_ENET1_TXC__NETCMIX_TOP_ETH0_RGMII_TX_CLK		0x58e>,
+			   <IMX95_PAD_ENET1_RX_CTL__NETCMIX_TOP_ETH0_RGMII_RX_CTL	0x57e>,
+			   <IMX95_PAD_ENET1_RXC__NETCMIX_TOP_ETH0_RGMII_RX_CLK		0x58e>,
+			   <IMX95_PAD_ENET1_RD0__NETCMIX_TOP_ETH0_RGMII_RD0		0x57e>,
+			   <IMX95_PAD_ENET1_RD1__NETCMIX_TOP_ETH0_RGMII_RD1		0x57e>,
+			   <IMX95_PAD_ENET1_RD2__NETCMIX_TOP_ETH0_RGMII_RD2		0x57e>,
+			   <IMX95_PAD_ENET1_RD3__NETCMIX_TOP_ETH0_RGMII_RD3		0x57e>;
+	};
+
+	pinctrl_i2c3_gpio_expander_21: i2c3gpioexpander21grp {
+		fsl,pins = <IMX95_PAD_ENET2_RD3__GPIO4_IO_BIT27				0x31e>;
+	};
+
+	pinctrl_lpi2c3: lpi2c3grp {
+		fsl,pins = <IMX95_PAD_GPIO_IO28__LPI2C3_SDA				0x40000b9e>,
+			   <IMX95_PAD_GPIO_IO29__LPI2C3_SCL				0x40000b9e>;
+	};
+
+	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
+		bootph-pre-ram;
+		fsl,pins = <IMX95_PAD_SD2_RESET_B__GPIO3_IO_BIT7			0x31e>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		bootph-pre-ram;
+		fsl,pins = <IMX95_PAD_UART1_RXD__AONMIX_TOP_LPUART1_RX			0x31e>,
+			   <IMX95_PAD_UART1_TXD__AONMIX_TOP_LPUART1_TX			0x31e>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
+		bootph-pre-ram;
+		fsl,pins = <IMX95_PAD_SD1_CLK__USDHC1_CLK				0x15fe>,
+			   <IMX95_PAD_SD1_CMD__USDHC1_CMD				0x13fe>,
+			   <IMX95_PAD_SD1_DATA0__USDHC1_DATA0				0x13fe>,
+			   <IMX95_PAD_SD1_DATA1__USDHC1_DATA1				0x13fe>,
+			   <IMX95_PAD_SD1_DATA2__USDHC1_DATA2				0x13fe>,
+			   <IMX95_PAD_SD1_DATA3__USDHC1_DATA3				0x13fe>,
+			   <IMX95_PAD_SD1_DATA4__USDHC1_DATA4				0x13fe>,
+			   <IMX95_PAD_SD1_DATA5__USDHC1_DATA5				0x13fe>,
+			   <IMX95_PAD_SD1_DATA6__USDHC1_DATA6				0x13fe>,
+			   <IMX95_PAD_SD1_DATA7__USDHC1_DATA7				0x13fe>,
+			   <IMX95_PAD_SD1_STROBE__USDHC1_STROBE				0x15fe>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		bootph-pre-ram;
+		fsl,pins = <IMX95_PAD_SD1_CLK__USDHC1_CLK				0x158e>,
+			   <IMX95_PAD_SD1_CMD__USDHC1_CMD				0x138e>,
+			   <IMX95_PAD_SD1_DATA0__USDHC1_DATA0				0x138e>,
+			   <IMX95_PAD_SD1_DATA1__USDHC1_DATA1				0x138e>,
+			   <IMX95_PAD_SD1_DATA2__USDHC1_DATA2				0x138e>,
+			   <IMX95_PAD_SD1_DATA3__USDHC1_DATA3				0x138e>,
+			   <IMX95_PAD_SD1_DATA4__USDHC1_DATA4				0x138e>,
+			   <IMX95_PAD_SD1_DATA5__USDHC1_DATA5				0x138e>,
+			   <IMX95_PAD_SD1_DATA6__USDHC1_DATA6				0x138e>,
+			   <IMX95_PAD_SD1_DATA7__USDHC1_DATA7				0x138e>,
+			   <IMX95_PAD_SD1_STROBE__USDHC1_STROBE				0x158e>;
+	};
+
+	pinctrl_usdhc2_gpio: usdhc2gpiogrp {
+		bootph-pre-ram;
+		fsl,pins = <IMX95_PAD_SD2_CD_B__GPIO3_IO_BIT0				0x31e>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		bootph-pre-ram;
+		fsl,pins = <IMX95_PAD_SD2_CLK__USDHC2_CLK				0x158e>,
+			   <IMX95_PAD_SD2_CMD__USDHC2_CMD				0x138e>,
+			   <IMX95_PAD_SD2_DATA0__USDHC2_DATA0				0x138e>,
+			   <IMX95_PAD_SD2_DATA1__USDHC2_DATA1				0x138e>,
+			   <IMX95_PAD_SD2_DATA2__USDHC2_DATA2				0x138e>,
+			   <IMX95_PAD_SD2_DATA3__USDHC2_DATA3				0x138e>,
+			   <IMX95_PAD_SD2_VSELECT__USDHC2_VSELECT			0x51e>;
+	};
+};
+
+&usdhc1 {
+	bootph-pre-ram;
+	bus-width = <8>;
+	no-sd;
+	no-sdio;
+	non-removable;
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	pinctrl-3 = <&pinctrl_usdhc1>;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+
+	status = "okay";
+};
+
+&usdhc2 {
+	bootph-pre-ram;
+	bus-width = <4>;
+	cd-gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-3 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+
+	status = "okay";
+};
-- 
2.53.0