* [PATCH v4 1/2] arm64: dts: qcom: rubikpi3: Add qcs6490-rubikpi3 board dts
2025-09-30 4:32 [PATCH v4 0/2] arm64: dts: qcom: rubikpi3: Add qcs6490-rubikpi3 board dts Hongyang Zhao
@ 2025-09-30 4:32 ` Hongyang Zhao
2025-10-06 10:33 ` Konrad Dybcio
2025-09-30 4:32 ` [PATCH v4 2/2] dt-bindings: arm: qcom: rubikpi3: document rubikpi3 board binding Hongyang Zhao
1 sibling, 1 reply; 11+ messages in thread
From: Hongyang Zhao @ 2025-09-30 4:32 UTC (permalink / raw)
To: linux-arm-msm
Cc: casey.connolly, christopher.obbard, loic.minier, andersson,
Hongyang Zhao, Roger Shimizu
Add DTS for Thundercomm qcs6490-rubikpi3 board which uses
QCS6490 SoC.
Works:
- Wi-Fi (AP6256)
- Bluetooth (AP6256)
- Ethernet (AX88179B connected to UPD720201)
- USB Type-C
- USB Type-A 2.0 port
- Two USB Type-A 3.0 ports (UPD720201 connected to PCIe0)
- M.2 M-Key 2280 PCIe 3.0
- RTC
- 40PIN: I2C x1, UART x1
Signed-off-by: Hongyang Zhao <hongyang.zhao@thundersoft.com>
Reviewed-by: Roger Shimizu <rosh@debian.org>
Cc: Casey Connolly <casey.connolly@linaro.org>
Cc: Christopher Obbard <christopher.obbard@linaro.org>
Cc: Loic Minier V1<loic.minier@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
.../dts/qcom/qcs6490-thundercomm-rubikpi3.dts | 1410 +++++++++++++++++
2 files changed, 1411 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/qcs6490-thundercomm-rubikpi3.dts
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 296688f7cb26..74938791f62d 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -133,6 +133,7 @@ qcs6490-rb3gen2-industrial-mezzanine-dtbs := qcs6490-rb3gen2.dtb qcs6490-rb3gen2
dtb-$(CONFIG_ARCH_QCOM) += qcs6490-rb3gen2-industrial-mezzanine.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs6490-rb3gen2-vision-mezzanine.dtb
+dtb-$(CONFIG_ARCH_QCOM) += qcs6490-thundercomm-rubikpi3.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs8300-ride.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs8550-aim300-aiot.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs9100-ride.dtb
diff --git a/arch/arm64/boot/dts/qcom/qcs6490-thundercomm-rubikpi3.dts b/arch/arm64/boot/dts/qcom/qcs6490-thundercomm-rubikpi3.dts
new file mode 100644
index 000000000000..e09a94819565
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/qcs6490-thundercomm-rubikpi3.dts
@@ -0,0 +1,1410 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2025, Thundercomm All rights reserved.
+ */
+
+/dts-v1/;
+
+/* PM7250B is configured to use SID8/9 */
+#define PM7250B_SID 8
+#define PM7250B_SID1 9
+
+#include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h>
+#include <dt-bindings/iio/qcom,spmi-adc7-pm7325.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "sc7280.dtsi"
+#include "pm7250b.dtsi"
+#include "pm7325.dtsi"
+#include "pm8350c.dtsi"
+#include "pmk8350.dtsi"
+
+/delete-node/ &adsp_mem;
+/delete-node/ &cdsp_mem;
+/delete-node/ &ipa_fw_mem;
+/delete-node/ &mpss_mem;
+/delete-node/ &remoteproc_mpss;
+/delete-node/ &remoteproc_wpss;
+/delete-node/ &rmtfs_mem;
+/delete-node/ &video_mem;
+/delete-node/ &wifi;
+/delete-node/ &wlan_ce_mem;
+/delete-node/ &wlan_fw_mem;
+/delete-node/ &wpss_mem;
+/delete-node/ &xbl_mem;
+
+/ {
+ model = "Thundercomm RUBIK Pi 3";
+ compatible = "thundercomm,rubikpi3", "qcom,qcm6490";
+
+ chassis-type = "embedded";
+
+ aliases {
+ serial0 = &uart5;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ fan0: pwm-fan {
+ compatible = "pwm-fan";
+ pwms = <&pm8350c_pwm 3 1000000>;
+ pinctrl-0 = <&fan_pwm_out_default>;
+ pinctrl-names = "default";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ pinctrl-0 = <&kypd_vol_up_n>;
+ pinctrl-names = "default";
+
+ key-volume-up {
+ label = "Volume Up";
+ gpios = <&pm7325_gpios 6 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEUP>;
+ linux,can-disable;
+ };
+ };
+
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con: endpoint {
+ remote-endpoint = <<9611_out>;
+ };
+ };
+ };
+
+ pmic-glink {
+ compatible = "qcom,qcm6490-pmic-glink", "qcom,pmic-glink";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ orientation-gpios = <&tlmm 140 GPIO_ACTIVE_HIGH>;
+
+ connector@0 {
+ compatible = "usb-c-connector";
+ reg = <0>;
+ power-role = "dual";
+ data-role = "dual";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ pmic_glink_hs_in: endpoint {
+ remote-endpoint = <&usb_1_dwc3_hs>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ pmic_glink_ss_in: endpoint {
+ remote-endpoint = <&usb_dp_qmpphy_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ pmic_glink_sbu_in: endpoint {
+ remote-endpoint = <&usb1_sbu_mux>;
+ };
+ };
+ };
+ };
+ };
+
+ reserved-memory {
+ xbl_mem: xbl@80700000 {
+ reg = <0x0 0x80700000 0x0 0x100000>;
+ no-map;
+ };
+
+ cdsp_secure_heap_mem: cdsp-secure-heap@81800000 {
+ reg = <0x0 0x81800000 0x0 0x1e00000>;
+ no-map;
+ };
+
+ camera_mem: camera@84300000 {
+ reg = <0x0 0x84300000 0x0 0x500000>;
+ no-map;
+ };
+
+ adsp_mem: adsp@86100000 {
+ reg = <0x0 0x86100000 0x0 0x2800000>;
+ no-map;
+ };
+
+ cdsp_mem: cdsp@88900000 {
+ reg = <0x0 0x88900000 0x0 0x1e00000>;
+ no-map;
+ };
+
+ video_mem: video@8a700000 {
+ reg = <0x0 0x8a700000 0x0 0x700000>;
+ no-map;
+ };
+
+ cvp_mem: cvp@8ae00000 {
+ reg = <0x0 0x8ae00000 0x0 0x500000>;
+ no-map;
+ };
+
+ gpu_microcode_mem: gpu-microcode@8b31a000 {
+ reg = <0x0 0x8b31a000 0x0 0x2000>;
+ no-map;
+ };
+
+ tz_stat_mem: tz-stat@c0000000 {
+ reg = <0x0 0xc0000000 0x0 0x100000>;
+ no-map;
+ };
+
+ tags_mem: tags@c0100000 {
+ reg = <0x0 0xc0100000 0x0 0x1200000>;
+ no-map;
+ };
+
+ qtee_mem: qtee@c1300000 {
+ reg = <0x0 0xc1300000 0x0 0x500000>;
+ no-map;
+ };
+
+ trusted_apps_mem: trusted-apps@c1800000 {
+ reg = <0x0 0xc1800000 0x0 0x1c00000>;
+ no-map;
+ };
+
+ debug_vm_mem: debug-vm@d0600000 {
+ reg = <0x0 0xd0600000 0x0 0x100000>;
+ no-map;
+ };
+ };
+
+ thermal-zones {
+ sdm-skin-thermal {
+ thermal-sensors = <&pmk8350_adc_tm 3>;
+
+ trips {
+ active-config0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ quiet-thermal {
+ thermal-sensors = <&pmk8350_adc_tm 1>;
+
+ trips {
+ active-config0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ xo-thermal {
+ thermal-sensors = <&pmk8350_adc_tm 0>;
+
+ trips {
+ active-config0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+ };
+
+ usb1-sbu-mux {
+ compatible = "pericom,pi3usb102", "gpio-sbu-mux";
+ enable-gpios = <&tlmm 53 GPIO_ACTIVE_LOW>;
+ select-gpios = <&tlmm 52 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&usb1_sbu_default>;
+ pinctrl-names = "default";
+ mode-switch;
+ orientation-switch;
+
+ port {
+ usb1_sbu_mux: endpoint {
+ remote-endpoint = <&pmic_glink_sbu_in>;
+ };
+ };
+ };
+
+ vreg_lt9611_3p3: vreg_lt9611_3p3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "vreg_lt9611_3p3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 83 0>;
+ enable-active-high;
+
+ pinctrl-0 = <<9611_vcc_pin>;
+ pinctrl-names = "default";
+ };
+
+ vreg_m2_1p8: vreg_m2_1p8 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "vreg_m2_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-enable-ramp-delay = <50000>;
+
+ gpio = <&tlmm 56 0>;
+ enable-active-high;
+
+ pinctrl-0 = <&m2_vcc_pin>;
+ pinctrl-names = "default";
+
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vph_pwr: vph-pwr-regulator {
+ compatible = "regulator-fixed";
+
+ regulator-name = "vph_pwr";
+ regulator-min-microvolt = <3700000>;
+ regulator-max-microvolt = <3700000>;
+ };
+
+ vreg_sdio_wifi_1p8: vreg_sdio_wifi_1p8 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "vreg_sdio_wifi_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-enable-ramp-delay = <50000>;
+
+ gpio = <&tlmm 125 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&wifi_reset_active>,
+ <&wifi_host_wake>,
+ <&wifi_power_on>;
+ pinctrl-names = "default";
+
+ regulator-always-on;
+ };
+
+ vreg_usbhub_1p8: vreg_usbhub_1p8 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "vreg_usbhub_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-enable-ramp-delay = <50000>;
+
+ gpio = <&tlmm 86 0>;
+ enable-active-high;
+
+ pinctrl-0 = <&usbhub_power>;
+ pinctrl-names = "default";
+
+ regulator-always-on;
+ };
+
+ vreg_usb_eth_1p8: vreg_usb_eth_1p8 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "vreg_usb_eth_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-enable-ramp-delay = <50000>;
+
+ gpio = <&tlmm 7 0>;
+ enable-active-high;
+
+ pinctrl-0 = <&usb_eth_power>;
+ pinctrl-names = "default";
+
+ vin-supply = <&vreg_usbhub_1p8>;
+ };
+
+ vreg_usbhub_rest: vreg_usbhub_rest {
+ compatible = "regulator-fixed";
+
+ regulator-name = "vreg_usbhub_rest";
+ regulator-min-microvolt = <1800000>;
+ regulator-enable-ramp-delay = <50000>;
+ regulator-max-microvolt = <1800000>;
+
+ gpio = <&tlmm 136 0>;
+ enable-active-high;
+
+ pinctrl-0 = <&usbhub_rest>;
+ pinctrl-names = "default";
+
+ vin-supply = <&vreg_usb_eth_1p8>;
+
+ regulator-always-on;
+ regulator-boot-on;
+ };
+};
+
+&apps_rsc {
+ regulators-0 {
+ compatible = "qcom,pm7325-rpmh-regulators";
+ qcom,pmic-id = "b";
+
+ vdd-s1-supply = <&vph_pwr>;
+ vdd-s2-supply = <&vph_pwr>;
+ vdd-s3-supply = <&vph_pwr>;
+ vdd-s4-supply = <&vph_pwr>;
+ vdd-s5-supply = <&vph_pwr>;
+ vdd-s6-supply = <&vph_pwr>;
+ vdd-s7-supply = <&vph_pwr>;
+ vdd-s8-supply = <&vph_pwr>;
+ vdd-l1-l4-l12-l15-supply = <&vreg_s7b_0p972>;
+ vdd-l2-l7-supply = <&vreg_bob_3p296>;
+ vdd-l3-supply = <&vreg_s2b_0p876>;
+ vdd-l5-supply = <&vreg_s2b_0p876>;
+ vdd-l6-l9-l10-supply = <&vreg_s8b_1p272>;
+ vdd-l8-supply = <&vreg_s7b_0p972>;
+ vdd-l11-l17-l18-l19-supply = <&vreg_s1b_1p872>;
+ vdd-l13-supply = <&vreg_s7b_0p972>;
+ vdd-l14-l16-supply = <&vreg_s8b_1p272>;
+
+ vreg_s1b_1p872: smps1 {
+ regulator-name = "vreg_s1b_1p872";
+ regulator-min-microvolt = <1840000>;
+ regulator-max-microvolt = <2040000>;
+ };
+
+ vreg_s2b_0p876: smps2 {
+ regulator-name = "vreg_s2b_0p876";
+ regulator-min-microvolt = <570070>;
+ regulator-max-microvolt = <1050000>;
+ };
+
+ vreg_s7b_0p972: smps7 {
+ regulator-name = "vreg_s7b_0p972";
+ regulator-min-microvolt = <535000>;
+ regulator-max-microvolt = <1120000>;
+ };
+
+ vreg_s8b_1p272: smps8 {
+ regulator-name = "vreg_s8b_1p272";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_RET>;
+ };
+
+ vreg_l1b_0p912: ldo1 {
+ regulator-name = "vreg_l1b_0p912";
+ regulator-min-microvolt = <825000>;
+ regulator-max-microvolt = <925000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2b_3p072: ldo2 {
+ regulator-name = "vreg_l2b_3p072";
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3544000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3b_0p504: ldo3 {
+ regulator-name = "vreg_l3b_0p504";
+ regulator-min-microvolt = <312000>;
+ regulator-max-microvolt = <910000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4b_0p752: ldo4 {
+ regulator-name = "vreg_l4b_0p752";
+ regulator-min-microvolt = <752000>;
+ regulator-max-microvolt = <820000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ reg_l5b_0p752: ldo5 {
+ regulator-name = "reg_l5b_0p752";
+ regulator-min-microvolt = <552000>;
+ regulator-max-microvolt = <832000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6b_1p2: ldo6 {
+ regulator-name = "vreg_l6b_1p2";
+ regulator-min-microvolt = <1140000>;
+ regulator-max-microvolt = <1260000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7b_2p952: ldo7 {
+ regulator-name = "vreg_l7b_2p952";
+ regulator-min-microvolt = <2952000>;
+ regulator-max-microvolt = <2952000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8b_0p904: ldo8 {
+ regulator-name = "vreg_l8b_0p904";
+ regulator-min-microvolt = <870000>;
+ regulator-max-microvolt = <970000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l9b_1p2: ldo9 {
+ regulator-name = "vreg_l9b_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l11b_1p504: ldo11 {
+ regulator-name = "vreg_l11b_1p504";
+ regulator-min-microvolt = <1504000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l12b_0p751: ldo12 {
+ regulator-name = "vreg_l12b_0p751";
+ regulator-min-microvolt = <751000>;
+ regulator-max-microvolt = <824000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l13b_0p53: ldo13 {
+ regulator-name = "vreg_l13b_0p53";
+ regulator-min-microvolt = <530000>;
+ regulator-max-microvolt = <824000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l14b_1p08: ldo14 {
+ regulator-name = "vreg_l14b_1p08";
+ regulator-min-microvolt = <1080000>;
+ regulator-max-microvolt = <1304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l15b_0p765: ldo15 {
+ regulator-name = "vreg_l15b_0p765";
+ regulator-min-microvolt = <765000>;
+ regulator-max-microvolt = <1020000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l16b_1p1: ldo16 {
+ regulator-name = "vreg_l16b_1p1";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l17b_1p7: ldo17 {
+ regulator-name = "vreg_l17b_1p7";
+ regulator-min-microvolt = <1700000>;
+ regulator-max-microvolt = <1900000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l18b_1p8: ldo18 {
+ regulator-name = "vreg_l18b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l19b_1p8: ldo19 {
+ regulator-name = "vreg_l19b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-1 {
+ compatible = "qcom,pm8350c-rpmh-regulators";
+ qcom,pmic-id = "c";
+
+ vdd-s1-supply = <&vph_pwr>;
+ vdd-s2-supply = <&vph_pwr>;
+ vdd-s3-supply = <&vph_pwr>;
+ vdd-s4-supply = <&vph_pwr>;
+ vdd-s5-supply = <&vph_pwr>;
+ vdd-s6-supply = <&vph_pwr>;
+ vdd-s7-supply = <&vph_pwr>;
+ vdd-s8-supply = <&vph_pwr>;
+ vdd-s9-supply = <&vph_pwr>;
+ vdd-s10-supply = <&vph_pwr>;
+ vdd-l1-l12-supply = <&vreg_s1b_1p872>;
+ vdd-l2-l8-supply = <&vreg_s1b_1p872>;
+ vdd-l3-l4-l5-l7-l13-supply = <&vreg_bob_3p296>;
+ vdd-l6-l9-l11-supply = <&vreg_bob_3p296>;
+ vdd-l10-supply = <&vreg_s7b_0p972>;
+ vdd-bob-supply = <&vph_pwr>;
+
+ vreg_s1c_2p19: smps1 {
+ regulator-name = "vreg_s1c_2p19";
+ regulator-min-microvolt = <2190000>;
+ regulator-max-microvolt = <2210000>;
+ };
+
+ vreg_s2c_0p752: smps2 {
+ regulator-name = "vreg_s2c_0p752";
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <800000>;
+ };
+
+ vreg_s5c_0p752: smps5 {
+ regulator-name = "vreg_s5c_0p752";
+ regulator-min-microvolt = <465000>;
+ regulator-max-microvolt = <1050000>;
+ };
+
+ vreg_s7c_0p752: smps7 {
+ regulator-name = "vreg_s7c_0p752";
+ regulator-min-microvolt = <465000>;
+ regulator-max-microvolt = <800000>;
+ };
+
+ vreg_s9c_1p084: smps9 {
+ regulator-name = "vreg_s9c_1p084";
+ regulator-min-microvolt = <1010000>;
+ regulator-max-microvolt = <1170000>;
+ };
+
+ vreg_l1c_1p8: ldo1 {
+ regulator-name = "vreg_l1c_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1980000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2c_1p62: ldo2 {
+ regulator-name = "vreg_l2c_1p62";
+ regulator-min-microvolt = <1620000>;
+ regulator-max-microvolt = <1980000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3c_2p8: ldo3 {
+ regulator-name = "vreg_l3c_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3540000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4c_1p62: ldo4 {
+ regulator-name = "vreg_l4c_1p62";
+ regulator-min-microvolt = <1620000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5c_1p62: ldo5 {
+ regulator-name = "vreg_l5c_1p62";
+ regulator-min-microvolt = <1620000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6c_2p96: ldo6 {
+ regulator-name = "vreg_l6c_2p96";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7c_3p0: ldo7 {
+ regulator-name = "vreg_l7c_3p0";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3544000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8c_1p62: ldo8 {
+ regulator-name = "vreg_l8c_1p62";
+ regulator-min-microvolt = <1620000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l9c_2p96: ldo9 {
+ regulator-name = "vreg_l9c_2p96";
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3544000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l10c_0p88: ldo10 {
+ regulator-name = "vreg_l10c_0p88";
+ regulator-min-microvolt = <720000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l11c_2p8: ldo11 {
+ regulator-name = "vreg_l11c_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3544000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l12c_1p65: ldo12 {
+ regulator-name = "vreg_l12c_1p65";
+ regulator-min-microvolt = <1650000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l13c_2p7: ldo13 {
+ regulator-name = "vreg_l13c_2p7";
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3544000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_bob_3p296: bob {
+ regulator-name = "vreg_bob_3p296";
+ regulator-min-microvolt = <3008000>;
+ regulator-max-microvolt = <3960000>;
+ };
+ };
+};
+
+&gcc {
+ protected-clocks = <GCC_CFG_NOC_LPASS_CLK>,
+ <GCC_MSS_CFG_AHB_CLK>,
+ <GCC_MSS_GPLL0_MAIN_DIV_CLK_SRC>,
+ <GCC_MSS_OFFLINE_AXI_CLK>,
+ <GCC_MSS_Q6SS_BOOT_CLK_SRC>,
+ <GCC_MSS_Q6_MEMNOC_AXI_CLK>,
+ <GCC_MSS_SNOC_AXI_CLK>,
+ <GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
+ <GCC_QSPI_CORE_CLK>,
+ <GCC_QSPI_CORE_CLK_SRC>,
+ <GCC_SEC_CTRL_CLK_SRC>,
+ <GCC_WPSS_AHB_BDG_MST_CLK>,
+ <GCC_WPSS_AHB_CLK>,
+ <GCC_WPSS_RSCP_CLK>;
+};
+
+&gpi_dma0 {
+ status = "okay";
+};
+
+&gpi_dma1 {
+ status = "okay";
+};
+
+&gpu {
+ status = "okay";
+};
+
+&gpu_zap_shader {
+ firmware-name = "qcom/qcs6490/a660_zap.mbn";
+};
+
+/* Pin 3, 5 in 40-pin connector */
+&i2c1 {
+ status = "okay";
+};
+
+&i2c9 {
+ clock-frequency = <400000>;
+
+ status = "okay";
+
+ lt9611_codec: hdmi-bridge@39 {
+ compatible = "lontium,lt9611";
+ reg = <0x39>;
+
+ interrupts-extended = <&tlmm 20 IRQ_TYPE_EDGE_FALLING>;
+ reset-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
+
+ vdd-supply = <&vreg_lt9611_3p3>;
+ vcc-supply = <&vreg_lt9611_3p3>;
+
+ pinctrl-0 = <<9611_irq_pin>,
+ <<9611_rst_pin>;
+ pinctrl-names = "default";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ lt9611_a: endpoint {
+ remote-endpoint = <&mdss_dsi0_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ lt9611_out: endpoint {
+ remote-endpoint = <&hdmi_con>;
+ };
+ };
+ };
+ };
+};
+
+&mdss {
+ status = "okay";
+};
+
+&mdss_dp {
+ status = "okay";
+};
+
+&mdss_dp_out {
+ data-lanes = <0 1>;
+ link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+
+ remote-endpoint = <&usb_dp_qmpphy_dp_in>;
+};
+
+&mdss_dsi {
+ vdda-supply = <&vreg_l6b_1p2>;
+
+ status = "okay";
+};
+
+&mdss_dsi0_out {
+ remote-endpoint = <<9611_a>;
+ data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi_phy {
+ vdds-supply = <&vreg_l10c_0p88>;
+
+ status = "okay";
+};
+
+&pcie0 {
+ status = "okay";
+};
+
+&pcie0_phy {
+ status = "okay";
+ vdda-phy-supply = <&vreg_l10c_0p88>;
+ vdda-pll-supply = <&vreg_l6b_1p2>;
+};
+
+&pcie1 {
+ perst-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 3 GPIO_ACTIVE_LOW>;
+
+ pinctrl-0 = <&pcie1_reset_n>,
+ <&pcie1_wake_n>,
+ <&pcie1_clkreq_n>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&pcie1_phy {
+ vdda-phy-supply = <&vreg_l10c_0p88>;
+ vdda-pll-supply = <&vreg_l6b_1p2>;
+
+ status = "okay";
+};
+
+&pm7325_gpios {
+ kypd_vol_up_n: kypd-vol-up-n-state {
+ pins = "gpio6";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ power-source = <1>;
+ bias-pull-up;
+ input-enable;
+ };
+};
+
+&pm7325_temp_alarm {
+ io-channels = <&pmk8350_vadc PM7325_ADC7_DIE_TEMP>;
+ io-channel-names = "thermal";
+};
+
+&pmk8350_adc_tm {
+ status = "okay";
+
+ xo-therm@0 {
+ reg = <0>;
+ io-channels = <&pmk8350_vadc PMK8350_ADC7_AMUX_THM1_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time-us = <200>;
+ };
+
+ quiet-therm@1 {
+ reg = <1>;
+ io-channels = <&pmk8350_vadc PM7325_ADC7_AMUX_THM1_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time-us = <200>;
+ };
+
+ sdm-skin-therm@3 {
+ reg = <3>;
+ io-channels = <&pmk8350_vadc PM7325_ADC7_AMUX_THM3_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time-us = <200>;
+ };
+};
+
+&pm8350c_pwm {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "okay";
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_INDICATOR;
+ function-enumerator = <3>;
+ linux,default-trigger = "none";
+ default-state = "off";
+ panic-indicator;
+ label = "red";
+ };
+
+ led@2 {
+ reg = <2>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_INDICATOR;
+ function-enumerator = <2>;
+ linux,default-trigger = "none";
+ default-state = "off";
+ label = "green";
+ };
+
+ led@3 {
+ reg = <3>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_INDICATOR;
+ function-enumerator = <1>;
+ linux,default-trigger = "none";
+ default-state = "off";
+ label = "blue";
+ };
+};
+
+&pm8350c_gpios {
+ fan_pwm_out_default: fan-pwm-out-default-state {
+ pins = "gpio8";
+ function = "func1";
+ power-source = <1>;
+ drive-push-pull;
+ output-high;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+ };
+};
+
+&pmk8350_rtc {
+ allow-set-time;
+
+ status = "okay";
+};
+
+&pmk8350_vadc {
+ channel@3 {
+ reg = <PMK8350_ADC7_DIE_TEMP>;
+ label = "pmk8350_die_temp";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ channel@44 {
+ reg = <PMK8350_ADC7_AMUX_THM1_100K_PU>;
+ label = "xo_therm";
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ qcom,ratiometric;
+ };
+
+ channel@103 {
+ reg = <PM7325_ADC7_DIE_TEMP>;
+ label = "pm7325_die_temp";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ channel@144 {
+ reg = <PM7325_ADC7_AMUX_THM1_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ label = "pm7325_quiet_therm";
+ };
+
+ channel@146 {
+ reg = <PM7325_ADC7_AMUX_THM3_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ label = "pm7325_sdm_skin_therm";
+ };
+};
+
+&pon_pwrkey {
+ status = "okay";
+};
+
+&pon_resin {
+ linux,code = <KEY_VOLUMEDOWN>;
+
+ status = "okay";
+};
+
+&qup_uart7_cts {
+ /*
+ * Configure a bias-bus-hold on CTS to lower power
+ * usage when Bluetooth is turned off. Bus hold will
+ * maintain a low power state regardless of whether
+ * the Bluetooth module drives the pin in either
+ * direction or leaves the pin fully unpowered.
+ */
+ bias-bus-hold;
+};
+
+&qup_uart7_rts {
+ /* We'll drive RTS, so no pull */
+ drive-strength = <2>;
+ bias-disable;
+};
+
+&qup_uart7_rx {
+ /*
+ * Configure a pull-up on RX. This is needed to avoid
+ * garbage data when the TX pin of the Bluetooth module is
+ * in tri-state (module powered off or not driving the
+ * signal yet).
+ */
+ bias-pull-up;
+};
+
+&qup_uart7_tx {
+ /* We'll drive TX, so no pull */
+ drive-strength = <2>;
+ bias-disable;
+};
+
+&qupv3_id_0 {
+ status = "okay";
+};
+
+&qupv3_id_1 {
+ status = "okay";
+};
+
+&remoteproc_adsp {
+ firmware-name = "qcom/qcs6490/adsp.mbn";
+
+ status = "okay";
+};
+
+&remoteproc_cdsp {
+ firmware-name = "qcom/qcs6490/cdsp.mbn";
+
+ status = "okay";
+};
+
+/* WIFI part of the AP6256 connected with SDIO */
+&sdhc_2 {
+ vmmc-supply = <&vreg_l9c_2p96>;
+ vqmmc-supply = <&vreg_l6c_2p96>;
+
+ non-removable;
+ keep-power-in-suspend;
+ /delete-property/ cd-gpios;
+
+ status = "okay";
+};
+
+/* Pin 19, 21, 23, 24 in 40-pin connector */
+&spi12 {
+ status = "okay";
+};
+
+/* Pin 8, 10 in 40-pin connector */
+&uart2 {
+ status = "okay";
+};
+
+&uart5 {
+ status = "okay";
+};
+
+/* BT part of the AP6256 connected with UART */
+&uart7 {
+ /delete-property/ interrupts;
+ interrupts-extended = <&intc GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>,
+ <&tlmm 31 IRQ_TYPE_EDGE_FALLING>;
+ pinctrl-1 = <&qup_uart7_sleep_cts>,
+ <&qup_uart7_sleep_rts>,
+ <&qup_uart7_sleep_tx>,
+ <&qup_uart7_sleep_rx>;
+ pinctrl-names = "default",
+ "sleep";
+
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm4345c5";
+ clocks = <&sleep_clk>;
+ clock-names = "lpo";
+ device-wakeup-gpios = <&tlmm 39 GPIO_ACTIVE_HIGH>;
+ host-wakeup-gpios = <&tlmm 137 GPIO_ACTIVE_HIGH>;
+ shutdown-gpios = <&tlmm 17 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&bt_device_wake>,
+ <&bt_host_wake>,
+ <&bt_reset>;
+ pinctrl-names = "default";
+ vbat-supply = <&vreg_sdio_wifi_1p8>;
+ vddio-supply = <&vreg_sdio_wifi_1p8>;
+ max-speed = <3000000>;
+ };
+};
+
+&usb_1 {
+ dr_mode = "otg";
+
+ status = "okay";
+};
+
+&usb_1_dwc3_hs {
+ remote-endpoint = <&pmic_glink_hs_in>;
+};
+
+&usb_1_hsphy {
+ vdda-pll-supply = <&vreg_l10c_0p88>;
+ vdda33-supply = <&vreg_l2b_3p072>;
+ vdda18-supply = <&vreg_l1c_1p8>;
+
+ status = "okay";
+};
+
+&usb_1_qmpphy {
+ vdda-phy-supply = <&vreg_l6b_1p2>;
+ vdda-pll-supply = <&vreg_l1b_0p912>;
+
+ status = "okay";
+};
+
+&usb_2 {
+ dr_mode = "host";
+
+ status = "okay";
+};
+
+&usb_2_hsphy {
+ vdda-pll-supply = <&vreg_l10c_0p88>;
+ vdda18-supply = <&vreg_l1c_1p8>;
+ vdda33-supply = <&vreg_l2b_3p072>;
+
+ status = "okay";
+};
+
+&usb_dp_qmpphy_out {
+ remote-endpoint = <&pmic_glink_ss_in>;
+};
+
+&ufs_mem_hc {
+ reset-gpios = <&tlmm 175 GPIO_ACTIVE_LOW>;
+ vcc-supply = <&vreg_l7b_2p952>;
+ vcc-max-microamp = <800000>;
+ vccq-supply = <&vreg_l9b_1p2>;
+ vccq-max-microamp = <900000>;
+ vccq2-supply = <&vreg_l9b_1p2>;
+ vccq2-max-microamp = <900000>;
+
+ status = "okay";
+};
+
+&ufs_mem_phy {
+ vdda-phy-supply = <&vreg_l10c_0p88>;
+ vdda-pll-supply = <&vreg_l6b_1p2>;
+
+ status = "okay";
+};
+
+&venus {
+ status = "okay";
+};
+
+&thermal_zones {
+ cpu0-thermal {
+ trips {
+ cpu_tepid: cpu-tepid {
+ temperature = <65000>;
+ hysteresis = <5000>;
+ type = "active";
+ };
+
+ cpu_warm: cpu-warm {
+ temperature = <80000>;
+ hysteresis = <5000>;
+ type = "active";
+ };
+
+ cpu_hot: cpu-hot {
+ temperature = <90000>;
+ hysteresis = <5000>;
+ type = "active";
+ };
+ };
+ };
+
+ gpuss0-thermal {
+ trips {
+ gpuss0_alert0: trip-point0 {
+ temperature = <95000>;
+ hysteresis = <5000>;
+ type = "passive";
+ };
+ };
+ };
+
+ gpuss1-thermal {
+ trips {
+ gpuss1_alert0: trip-point0 {
+ temperature = <95000>;
+ hysteresis = <5000>;
+ type = "passive";
+ };
+ };
+ };
+
+ nspss0-thermal {
+ trips {
+ nspss0_alert0: trip-point0 {
+ temperature = <95000>;
+ hysteresis = <5000>;
+ type = "hot";
+ };
+ };
+ };
+
+ nspss1-thermal {
+ trips {
+ nspss1_alert0: trip-point0 {
+ temperature = <95000>;
+ hysteresis = <5000>;
+ type = "hot";
+ };
+ };
+ };
+};
+
+/* PINCTRL - ADDITIONS TO NODES IN PARENT DEVICE TREE FILES */
+&sdc2_clk {
+ bias-disable;
+ drive-strength = <16>;
+};
+
+&sdc2_cmd {
+ bias-pull-up;
+ drive-strength = <10>;
+};
+
+&sdc2_data {
+ bias-pull-up;
+ drive-strength = <10>;
+};
+
+&tlmm {
+ bt_device_wake: bt-device-wake-state {
+ pins = "gpio39";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ bt_host_wake: bt-host-wake-state {
+ pins = "gpio137";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ bt_reset: bt-reset-state {
+ pins = "gpio17";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ lt9611_vcc_pin: lt9611-vcc-pin-state {
+ pins = "gpio83";
+ function = "gpio";
+ output-high;
+ input-disable;
+ };
+
+ lt9611_irq_pin: lt9611-irq-state {
+ pins = "gpio20";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ lt9611_rst_pin: lt9611-rst-state {
+ pins = "gpio21";
+ function = "gpio";
+ output-high;
+ input-disable;
+ };
+
+ m2_vcc_pin: m2-vcc-state {
+ pins = "gpio56";
+ function = "gpio";
+ output-high;
+ input-disable;
+ };
+
+ pcie1_reset_n: pcie1-reset-n-state {
+ pins = "gpio2";
+ function = "gpio";
+ drive-strength = <16>;
+ output-low;
+ bias-disable;
+ };
+
+ pcie1_wake_n: pcie1-wake-n-state {
+ pins = "gpio3";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_uart7_sleep_cts: qup-uart7-sleep-cts-state {
+ pins = "gpio28";
+ function = "gpio";
+ /*
+ * Configure a bias-bus-hold on CTS to lower power
+ * usage when Bluetooth is turned off. Bus hold will
+ * maintain a low power state regardless of whether
+ * the Bluetooth module drives the pin in either
+ * direction or leaves the pin fully unpowered.
+ */
+ bias-bus-hold;
+ };
+
+ qup_uart7_sleep_rts: qup-uart7-sleep-rts-state {
+ pins = "gpio29";
+ function = "gpio";
+ /*
+ * Configure pull-down on RTS. As RTS is active low
+ * signal, pull it low to indicate the BT SoC that it
+ * can wakeup the system anytime from suspend state by
+ * pulling RX low (by sending wakeup bytes).
+ */
+ bias-pull-down;
+ };
+
+ qup_uart7_sleep_rx: qup-uart7-sleep-rx-state {
+ pins = "gpio31";
+ function = "gpio";
+ /*
+ * Configure a pull-up on RX. This is needed to avoid
+ * garbage data when the TX pin of the Bluetooth module
+ * is floating which may cause spurious wakeups.
+ */
+ bias-pull-up;
+ };
+
+ qup_uart7_sleep_tx: qup-uart7-sleep-tx-state {
+ pins = "gpio30";
+ function = "gpio";
+ /*
+ * Configure pull-up on TX when it isn't actively driven
+ * to prevent BT SoC from receiving garbage during sleep.
+ */
+ bias-pull-up;
+ };
+
+ usb1_sbu_default: usb1-sbu-state {
+ oe-n-pins {
+ pins = "gpio53";
+ function = "gpio";
+ bias-disable;
+ drive-strength = <16>;
+ output-high;
+ };
+ sel-pins {
+ pins = "gpio52";
+ function = "gpio";
+ bias-disable;
+ drive-strength = <16>;
+ };
+ };
+
+ usb_eth_power: usb-eth-power-state {
+ pins = "gpio7";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ usbhub_power: usbhub-power-state {
+ pins = "gpio86";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ usbhub_rest: usbhub-reset-state {
+ pins = "gpio136";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ wifi_host_wake: wifi-host-wake-state {
+ pins = "gpio38";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ wifi_power_on: wifi-power-on-state {
+ pins = "gpio125";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ wifi_reset_active: wifi-reset-active-state {
+ pins = "gpio16";
+ function = "gpio";
+ drive-strength = <2>;
+ output-high;
+ bias-disable;
+ };
+};
+
+/*
+ * Update the lpassaudio node to support the new compatible as the
+ * lpassaudio needs to support the reset functionality on the
+ * QCS6490 RUBIK Pi 3 board and the rest of the Audio functionality would be
+ * provided from the LPASS firmware.
+ */
+&lpass_audiocc {
+ compatible = "qcom,qcm6490-lpassaudiocc";
+ /delete-property/ power-domains;
+};
--
2.43.0
^ permalink raw reply related [flat|nested] 11+ messages in thread