[PATCH v5 0/4] PCI: dwc: Add support for configuring lane equalization presets

[PATCH v5 0/4] PCI: dwc: Add support for configuring lane equalization presets

[Krishna Chaitanya Chundru]

PCIe equalization presets are predefined settings used to optimize
signal integrity by compensating for signal loss and distortion in
high-speed data transmission.

As per PCIe spec 6.0.1 revision section 8.3.3.3 & 4.2.4 for data rates
of 8.0 GT/s, 16.0 GT/s, 32.0 GT/s, and 64.0 GT/s, there is a way to
configure lane equalization presets for each lane to enhance the PCIe
link reliability. Each preset value represents a different combination
of pre-shoot and de-emphasis values. For each data rate, different
registers are defined: for 8.0 GT/s, registers are defined in section
7.7.3.4; for 16.0 GT/s, in section 7.7.5.9, etc. The 8.0 GT/s rate has
an extra receiver preset hint, requiring 16 bits per lane, while the
remaining data rates use 8 bits per lane.

Based on the number of lanes and the supported data rate, read the
device tree property and stores in the presets structure.

Based upon the lane width and supported data rate update lane
equalization registers.

This patch depends on the this dt binding pull request which got recently
merged: https://github.com/devicetree-org/dt-schema/pull/146

Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
---
Changes in v5:
- Instead of using of_property_present use return value of
  of_property_read_u8_array to know about property is present or not and
  add a macro for reserved value(Konrad).
- Link to v4: https://lore.kernel.org/r/20250124-preset_v2-v4-0-0b512cad08e1@oss.qualcomm.com

Changes in v4:
- use static arrays for storing preset values and use default value 0xff
  to indicate the property is not present (Dimitry & konrad).
- Link to v3: https://lore.kernel.org/r/20241223-preset_v2-v3-0-a339f475caf5@oss.qualcomm.com

Changes in v3:
- In previous series a wrong patch was attached, correct it
- Link to v2: https://lore.kernel.org/r/20241212-preset_v2-v2-0-210430fbcd8a@oss.qualcomm.com

Changes in v2:
- Fix the kernel test robot error
- As suggested by konrad use for loop and read "eq-presets-%ugts", (8 << i)
- Link to v1: https://lore.kernel.org/r/20241116-presets-v1-0-878a837a4fee@quicinc.com

---
Krishna Chaitanya Chundru (4):
      arm64: dts: qcom: x1e80100: Add PCIe lane equalization preset properties
      PCI: of: Add API to retrieve equalization presets from device tree
      PCI: dwc: Improve handling of PCIe lane configuration
      PCI: dwc: Add support for configuring lane equalization presets

 arch/arm64/boot/dts/qcom/x1e80100.dtsi            |  8 +++++
 drivers/pci/controller/dwc/pcie-designware-host.c | 44 +++++++++++++++++++++++
 drivers/pci/controller/dwc/pcie-designware.c      | 12 ++++++-
 drivers/pci/controller/dwc/pcie-designware.h      |  4 +++
 drivers/pci/of.c                                  | 43 ++++++++++++++++++++++
 drivers/pci/pci.h                                 | 26 +++++++++++++-
 include/uapi/linux/pci_regs.h                     |  3 ++
 7 files changed, 138 insertions(+), 2 deletions(-)
---
base-commit: 87d6aab2389e5ce0197d8257d5f8ee965a67c4cd
change-id: 20241212-preset_v2-549b7acda9b7

Best regards,
-- 
Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>

[PATCH v5 1/4] arm64: dts: qcom: x1e80100: Add PCIe lane equalization preset properties

[Krishna Chaitanya Chundru]

Add PCIe lane equalization preset properties for 8 GT/s and 16 GT/s data
rates used in lane equalization procedure.

Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
---
This patch depends on the this dt binding pull request which got recently
merged: https://github.com/devicetree-org/dt-schema/pull/146
---
 arch/arm64/boot/dts/qcom/x1e80100.dtsi | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/x1e80100.dtsi b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
index a36076e3c56b..6a2074297030 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100.dtsi
+++ b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
@@ -2993,6 +2993,10 @@ &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
 			phys = <&pcie6a_phy>;
 			phy-names = "pciephy";
 
+			eq-presets-8gts = /bits/ 16 <0x5555 0x5555>;
+
+			eq-presets-16gts = /bits/ 8 <0x55 0x55>;
+
 			status = "disabled";
 		};
 
@@ -3115,6 +3119,8 @@ &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
 			phys = <&pcie5_phy>;
 			phy-names = "pciephy";
 
+			eq-presets-8gts = /bits/ 16 <0x5555 0x5555>;
+
 			status = "disabled";
 		};
 
@@ -3235,6 +3241,8 @@ &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
 			phys = <&pcie4_phy>;
 			phy-names = "pciephy";
 
+			eq-presets-8gts = /bits/ 16 <0x5555 0x5555>;
+
 			status = "disabled";
 
 			pcie4_port0: pcie@0 {

-- 
2.34.1

[PATCH v5 2/4] PCI: of: Add API to retrieve equalization presets from device tree

[Krishna Chaitanya Chundru]

PCIe equalization presets are predefined settings used to optimize
signal integrity by compensating for signal loss and distortion in
high-speed data transmission.

As per PCIe spec 6.0.1 revision section 8.3.3.3 & 4.2.4 for data rates
of 8.0 GT/s, 16.0 GT/s, 32.0 GT/s, and 64.0 GT/s, there is a way to
configure lane equalization presets for each lane to enhance the PCIe
link reliability. Each preset value represents a different combination
of pre-shoot and de-emphasis values. For each data rate, different
registers are defined: for 8.0 GT/s, registers are defined in section
7.7.3.4; for 16.0 GT/s, in section 7.7.5.9, etc. The 8.0 GT/s rate has
an extra receiver preset hint, requiring 16 bits per lane, while the
remaining data rates use 8 bits per lane.

Based on the number of lanes and the supported data rate, this function
reads the device tree property and stores in the presets structure.

Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
---
 drivers/pci/of.c  | 43 +++++++++++++++++++++++++++++++++++++++++++
 drivers/pci/pci.h | 26 +++++++++++++++++++++++++-
 2 files changed, 68 insertions(+), 1 deletion(-)

diff --git a/drivers/pci/of.c b/drivers/pci/of.c
index dacea3fc5128..835ffefb9741 100644
--- a/drivers/pci/of.c
+++ b/drivers/pci/of.c
@@ -826,3 +826,46 @@ u32 of_pci_get_slot_power_limit(struct device_node *node,
 	return slot_power_limit_mw;
 }
 EXPORT_SYMBOL_GPL(of_pci_get_slot_power_limit);
+
+/**
+ * of_pci_get_equalization_presets - Parses the "eq-presets-ngts" property.
+ *
+ * @dev: Device containing the properties.
+ * @presets: Pointer to store the parsed data.
+ * @num_lanes: Maximum number of lanes supported.
+ *
+ * If the property is present read and store the data in the preset structure
+ * assign default value 0xff to indicate property is not present.
+ *
+ * If the property is not found or is invalid, returns 0.
+ */
+int of_pci_get_equalization_presets(struct device *dev,
+				    struct pci_eq_presets *presets,
+				    int num_lanes)
+{
+	char name[20];
+	int ret;
+
+	presets->eq_presets_8gts[0] = PCI_EQ_RESV;
+	ret = of_property_read_u16_array(dev->of_node, "eq-presets-8gts",
+					 presets->eq_presets_8gts, num_lanes);
+	if (ret && ret != -EINVAL) {
+		dev_err(dev, "Error reading eq-presets-8gts %d\n", ret);
+		return ret;
+	}
+
+	for (int i = 0; i < EQ_PRESET_TYPE_MAX; i++) {
+		presets->eq_presets_Ngts[i][0] = PCI_EQ_RESV;
+		snprintf(name, sizeof(name), "eq-presets-%dgts", 8 << (i + 1));
+		ret = of_property_read_u8_array(dev->of_node, name,
+						presets->eq_presets_Ngts[i],
+						num_lanes);
+		if (ret && ret != -EINVAL) {
+			dev_err(dev, "Error %s %d\n", name, ret);
+			return ret;
+		}
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(of_pci_get_equalization_presets);
diff --git a/drivers/pci/pci.h b/drivers/pci/pci.h
index 14d00ce45bfa..1070b10751db 100644
--- a/drivers/pci/pci.h
+++ b/drivers/pci/pci.h
@@ -7,6 +7,8 @@
 /* Number of possible devfns: 0.0 to 1f.7 inclusive */
 #define MAX_NR_DEVFNS 256
 
+#define MAX_NR_LANES 16
+
 #define PCI_FIND_CAP_TTL	48
 
 #define PCI_VSEC_ID_INTEL_TBT	0x1234	/* Thunderbolt */
@@ -732,6 +734,20 @@ static inline u64 pci_rebar_size_to_bytes(int size)
 
 struct device_node;
 
+#define	PCI_EQ_RESV	0xff
+
+enum equalization_preset_type {
+	EQ_PRESET_TYPE_16GTS,
+	EQ_PRESET_TYPE_32GTS,
+	EQ_PRESET_TYPE_64GTS,
+	EQ_PRESET_TYPE_MAX
+};
+
+struct pci_eq_presets {
+	u16 eq_presets_8gts[MAX_NR_LANES];
+	u8 eq_presets_Ngts[EQ_PRESET_TYPE_MAX][MAX_NR_LANES];
+};
+
 #ifdef CONFIG_OF
 int of_pci_parse_bus_range(struct device_node *node, struct resource *res);
 int of_get_pci_domain_nr(struct device_node *node);
@@ -746,7 +762,9 @@ void pci_set_bus_of_node(struct pci_bus *bus);
 void pci_release_bus_of_node(struct pci_bus *bus);
 
 int devm_of_pci_bridge_init(struct device *dev, struct pci_host_bridge *bridge);
-
+int of_pci_get_equalization_presets(struct device *dev,
+				    struct pci_eq_presets *presets,
+				    int num_lanes);
 #else
 static inline int
 of_pci_parse_bus_range(struct device_node *node, struct resource *res)
@@ -793,6 +811,12 @@ static inline int devm_of_pci_bridge_init(struct device *dev, struct pci_host_br
 	return 0;
 }
 
+static inline int of_pci_get_equalization_presets(struct device *dev,
+						  struct pci_eq_presets *presets,
+						  int num_lanes)
+{
+	return 0;
+}
 #endif /* CONFIG_OF */
 
 struct of_changeset;

-- 
2.34.1

[PATCH v5 3/4] PCI: dwc: Improve handling of PCIe lane configuration

[Krishna Chaitanya Chundru]

Currently even if the number of lanes hardware supports is equal to
the number lanes provided in the devicetree, the driver is trying to
configure again the maximum number of lanes which is not needed.

Update number of lanes only when it is not equal to hardware capability.

And also if the num-lanes property is not present in the devicetree
update the num_lanes with the maximum hardware supports.

Introduce dw_pcie_link_get_max_link_width() to get the maximum lane
width the hardware supports.

Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
---
 drivers/pci/controller/dwc/pcie-designware-host.c |  3 +++
 drivers/pci/controller/dwc/pcie-designware.c      | 12 +++++++++++-
 drivers/pci/controller/dwc/pcie-designware.h      |  1 +
 3 files changed, 15 insertions(+), 1 deletion(-)

diff --git a/drivers/pci/controller/dwc/pcie-designware-host.c b/drivers/pci/controller/dwc/pcie-designware-host.c
index 3e41865c7290..2cd0acbf9e18 100644
--- a/drivers/pci/controller/dwc/pcie-designware-host.c
+++ b/drivers/pci/controller/dwc/pcie-designware-host.c
@@ -504,6 +504,9 @@ int dw_pcie_host_init(struct dw_pcie_rp *pp)
 
 	dw_pcie_iatu_detect(pci);
 
+	if (pci->num_lanes < 1)
+		pci->num_lanes = dw_pcie_link_get_max_link_width(pci);
+
 	/*
 	 * Allocate the resource for MSG TLP before programming the iATU
 	 * outbound window in dw_pcie_setup_rc(). Since the allocation depends
diff --git a/drivers/pci/controller/dwc/pcie-designware.c b/drivers/pci/controller/dwc/pcie-designware.c
index 6d6cbc8b5b2c..1007248d3525 100644
--- a/drivers/pci/controller/dwc/pcie-designware.c
+++ b/drivers/pci/controller/dwc/pcie-designware.c
@@ -736,6 +736,14 @@ static void dw_pcie_link_set_max_speed(struct dw_pcie *pci)
 
 }
 
+int dw_pcie_link_get_max_link_width(struct dw_pcie *pci)
+{
+	u8 cap = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
+	u32 lnkcap = dw_pcie_readl_dbi(pci, cap + PCI_EXP_LNKCAP);
+
+	return FIELD_GET(PCI_EXP_LNKCAP_MLW, lnkcap);
+}
+
 static void dw_pcie_link_set_max_link_width(struct dw_pcie *pci, u32 num_lanes)
 {
 	u32 lnkcap, lwsc, plc;
@@ -1069,6 +1077,7 @@ void dw_pcie_edma_remove(struct dw_pcie *pci)
 
 void dw_pcie_setup(struct dw_pcie *pci)
 {
+	int num_lanes = dw_pcie_link_get_max_link_width(pci);
 	u32 val;
 
 	dw_pcie_link_set_max_speed(pci);
@@ -1102,5 +1111,6 @@ void dw_pcie_setup(struct dw_pcie *pci)
 	val |= PORT_LINK_DLL_LINK_EN;
 	dw_pcie_writel_dbi(pci, PCIE_PORT_LINK_CONTROL, val);
 
-	dw_pcie_link_set_max_link_width(pci, pci->num_lanes);
+	if (num_lanes != pci->num_lanes)
+		dw_pcie_link_set_max_link_width(pci, pci->num_lanes);
 }
diff --git a/drivers/pci/controller/dwc/pcie-designware.h b/drivers/pci/controller/dwc/pcie-designware.h
index 347ab74ac35a..500e793c9361 100644
--- a/drivers/pci/controller/dwc/pcie-designware.h
+++ b/drivers/pci/controller/dwc/pcie-designware.h
@@ -486,6 +486,7 @@ void dw_pcie_write_dbi2(struct dw_pcie *pci, u32 reg, size_t size, u32 val);
 int dw_pcie_link_up(struct dw_pcie *pci);
 void dw_pcie_upconfig_setup(struct dw_pcie *pci);
 int dw_pcie_wait_for_link(struct dw_pcie *pci);
+int dw_pcie_link_get_max_link_width(struct dw_pcie *pci);
 int dw_pcie_prog_outbound_atu(struct dw_pcie *pci,
 			      const struct dw_pcie_ob_atu_cfg *atu);
 int dw_pcie_prog_inbound_atu(struct dw_pcie *pci, int index, int type,

-- 
2.34.1

[PATCH v5 4/4] PCI: dwc: Add support for configuring lane equalization presets

[Krishna Chaitanya Chundru]

PCIe equalization presets are predefined settings used to optimize
signal integrity by compensating for signal loss and distortion in
high-speed data transmission.

Based upon the number of lanes and the data rate supported, write
the preset data read from the device tree in to the lane equalization
control registers.

Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
---
 drivers/pci/controller/dwc/pcie-designware-host.c | 41 +++++++++++++++++++++++
 drivers/pci/controller/dwc/pcie-designware.h      |  3 ++
 include/uapi/linux/pci_regs.h                     |  3 ++
 3 files changed, 47 insertions(+)

diff --git a/drivers/pci/controller/dwc/pcie-designware-host.c b/drivers/pci/controller/dwc/pcie-designware-host.c
index 2cd0acbf9e18..f458b4c70053 100644
--- a/drivers/pci/controller/dwc/pcie-designware-host.c
+++ b/drivers/pci/controller/dwc/pcie-designware-host.c
@@ -507,6 +507,10 @@ int dw_pcie_host_init(struct dw_pcie_rp *pp)
 	if (pci->num_lanes < 1)
 		pci->num_lanes = dw_pcie_link_get_max_link_width(pci);
 
+	ret = of_pci_get_equalization_presets(dev, &pp->presets, pci->num_lanes);
+	if (ret)
+		goto err_free_msi;
+
 	/*
 	 * Allocate the resource for MSG TLP before programming the iATU
 	 * outbound window in dw_pcie_setup_rc(). Since the allocation depends
@@ -802,6 +806,42 @@ static int dw_pcie_iatu_setup(struct dw_pcie_rp *pp)
 	return 0;
 }
 
+static void dw_pcie_program_presets(struct dw_pcie *pci, u8 cap_id, u8 lane_eq_offset,
+				    u8 lane_reg_size, u8 *presets, u8 num_lanes)
+{
+	u32 cap;
+	int i;
+
+	cap = dw_pcie_find_ext_capability(pci, cap_id);
+	if (!cap)
+		return;
+
+	/*
+	 * Write preset values to the registers byte-by-byte for the given
+	 * number of lanes and register size.
+	 */
+	for (i = 0; i < num_lanes * lane_reg_size; i++)
+		dw_pcie_writeb_dbi(pci, cap + lane_eq_offset + i, presets[i]);
+}
+
+static void dw_pcie_config_presets(struct dw_pcie_rp *pp)
+{
+	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
+	enum pci_bus_speed speed = pcie_link_speed[pci->max_link_speed];
+
+	/* For data rate of 8 GT/S each lane equalization control is 16bits wide */
+	if (speed >= PCIE_SPEED_8_0GT && pp->presets.eq_presets_8gts[0] != PCI_EQ_RESV)
+		dw_pcie_program_presets(pci, PCI_EXT_CAP_ID_SECPCI, PCI_SECPCI_LE_CTRL,
+					0x2, (u8 *)pp->presets.eq_presets_8gts, pci->num_lanes);
+
+	/* For data rate of 16 GT/S each lane equalization control is 8bits wide */
+	if (speed >= PCIE_SPEED_16_0GT &&
+	    pp->presets.eq_presets_Ngts[EQ_PRESET_TYPE_16GTS][0] != PCI_EQ_RESV)
+		dw_pcie_program_presets(pci, PCI_EXT_CAP_ID_PL_16GT, PCI_PL_16GT_LE_CTRL,
+					0x1, pp->presets.eq_presets_Ngts[EQ_PRESET_TYPE_16GTS],
+					pci->num_lanes);
+}
+
 int dw_pcie_setup_rc(struct dw_pcie_rp *pp)
 {
 	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
@@ -855,6 +895,7 @@ int dw_pcie_setup_rc(struct dw_pcie_rp *pp)
 		PCI_COMMAND_MASTER | PCI_COMMAND_SERR;
 	dw_pcie_writel_dbi(pci, PCI_COMMAND, val);
 
+	dw_pcie_config_presets(pp);
 	/*
 	 * If the platform provides its own child bus config accesses, it means
 	 * the platform uses its own address translation component rather than
diff --git a/drivers/pci/controller/dwc/pcie-designware.h b/drivers/pci/controller/dwc/pcie-designware.h
index 500e793c9361..b12b33944df4 100644
--- a/drivers/pci/controller/dwc/pcie-designware.h
+++ b/drivers/pci/controller/dwc/pcie-designware.h
@@ -25,6 +25,8 @@
 #include <linux/pci-epc.h>
 #include <linux/pci-epf.h>
 
+#include "../../pci.h"
+
 /* DWC PCIe IP-core versions (native support since v4.70a) */
 #define DW_PCIE_VER_365A		0x3336352a
 #define DW_PCIE_VER_460A		0x3436302a
@@ -379,6 +381,7 @@ struct dw_pcie_rp {
 	bool			use_atu_msg;
 	int			msg_atu_index;
 	struct resource		*msg_res;
+	struct pci_eq_presets	presets;
 };
 
 struct dw_pcie_ep_ops {
diff --git a/include/uapi/linux/pci_regs.h b/include/uapi/linux/pci_regs.h
index 12323b3334a9..68fc8873bc60 100644
--- a/include/uapi/linux/pci_regs.h
+++ b/include/uapi/linux/pci_regs.h
@@ -1118,6 +1118,9 @@
 #define PCI_DLF_CAP		0x04	/* Capabilities Register */
 #define  PCI_DLF_EXCHANGE_ENABLE	0x80000000  /* Data Link Feature Exchange Enable */
 
+/* Secondary PCIe Capability 8.0 GT/s */
+#define PCI_SECPCI_LE_CTRL	0x0c /* Lane Equalization Control Register */
+
 /* Physical Layer 16.0 GT/s */
 #define PCI_PL_16GT_LE_CTRL	0x20	/* Lane Equalization Control Register */
 #define  PCI_PL_16GT_LE_CTRL_DSP_TX_PRESET_MASK		0x0000000F

-- 
2.34.1

Re: [PATCH v5 1/4] arm64: dts: qcom: x1e80100: Add PCIe lane equalization preset properties

[Konrad Dybcio]

On 28.01.2025 10:37 AM, Krishna Chaitanya Chundru wrote:
> Add PCIe lane equalization preset properties for 8 GT/s and 16 GT/s data
> rates used in lane equalization procedure.
> 
> Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
> ---
> This patch depends on the this dt binding pull request which got recently
> merged: https://github.com/devicetree-org/dt-schema/pull/146
> ---
>  arch/arm64/boot/dts/qcom/x1e80100.dtsi | 8 ++++++++
>  1 file changed, 8 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/x1e80100.dtsi b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> index a36076e3c56b..6a2074297030 100644
> --- a/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> +++ b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> @@ -2993,6 +2993,10 @@ &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
>  			phys = <&pcie6a_phy>;
>  			phy-names = "pciephy";
>  
> +			eq-presets-8gts = /bits/ 16 <0x5555 0x5555>;
> +
> +			eq-presets-16gts = /bits/ 8 <0x55 0x55>;

Think these should be 2x longer, for the 4-lane port?

otherwise the values seem in sync with what the bootloader does (good)

Konrad

Re: [PATCH v5 4/4] PCI: dwc: Add support for configuring lane equalization presets

[Konrad Dybcio]

On 28.01.2025 10:37 AM, Krishna Chaitanya Chundru wrote:
> PCIe equalization presets are predefined settings used to optimize
> signal integrity by compensating for signal loss and distortion in
> high-speed data transmission.
> 
> Based upon the number of lanes and the data rate supported, write
> the preset data read from the device tree in to the lane equalization
> control registers.
> 
> Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
> ---
>  drivers/pci/controller/dwc/pcie-designware-host.c | 41 +++++++++++++++++++++++
>  drivers/pci/controller/dwc/pcie-designware.h      |  3 ++
>  include/uapi/linux/pci_regs.h                     |  3 ++
>  3 files changed, 47 insertions(+)
> 
> diff --git a/drivers/pci/controller/dwc/pcie-designware-host.c b/drivers/pci/controller/dwc/pcie-designware-host.c
> index 2cd0acbf9e18..f458b4c70053 100644
> --- a/drivers/pci/controller/dwc/pcie-designware-host.c
> +++ b/drivers/pci/controller/dwc/pcie-designware-host.c
> @@ -507,6 +507,10 @@ int dw_pcie_host_init(struct dw_pcie_rp *pp)
>  	if (pci->num_lanes < 1)
>  		pci->num_lanes = dw_pcie_link_get_max_link_width(pci);
>  
> +	ret = of_pci_get_equalization_presets(dev, &pp->presets, pci->num_lanes);
> +	if (ret)
> +		goto err_free_msi;
> +
>  	/*
>  	 * Allocate the resource for MSG TLP before programming the iATU
>  	 * outbound window in dw_pcie_setup_rc(). Since the allocation depends
> @@ -802,6 +806,42 @@ static int dw_pcie_iatu_setup(struct dw_pcie_rp *pp)
>  	return 0;
>  }
>  
> +static void dw_pcie_program_presets(struct dw_pcie *pci, u8 cap_id, u8 lane_eq_offset,
> +				    u8 lane_reg_size, u8 *presets, u8 num_lanes)
> +{
> +	u32 cap;
> +	int i;
> +
> +	cap = dw_pcie_find_ext_capability(pci, cap_id);
> +	if (!cap)
> +		return;
> +
> +	/*
> +	 * Write preset values to the registers byte-by-byte for the given
> +	 * number of lanes and register size.
> +	 */
> +	for (i = 0; i < num_lanes * lane_reg_size; i++)
> +		dw_pcie_writeb_dbi(pci, cap + lane_eq_offset + i, presets[i]);
> +}
> +
> +static void dw_pcie_config_presets(struct dw_pcie_rp *pp)
> +{
> +	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
> +	enum pci_bus_speed speed = pcie_link_speed[pci->max_link_speed];
> +
> +	/* For data rate of 8 GT/S each lane equalization control is 16bits wide */
> +	if (speed >= PCIE_SPEED_8_0GT && pp->presets.eq_presets_8gts[0] != PCI_EQ_RESV)
> +		dw_pcie_program_presets(pci, PCI_EXT_CAP_ID_SECPCI, PCI_SECPCI_LE_CTRL,
> +					0x2, (u8 *)pp->presets.eq_presets_8gts, pci->num_lanes);

If you move the != RESERVED into dw_pcie_program_presets, this becomes more readable

otherwise, this looks good

Konrad