[PATCH] arm64: dts: qcom: lemans-evk: Add OTG support for primary USB controller

[PATCH] arm64: dts: qcom: lemans-evk: Add OTG support for primary USB controller

[Krishna Kurapati]

Enable OTG support for primary USB controller on EVK Platform. Add
HD3SS3220 Type-C port controller present between Type-C port and SoC
that provides role switch notifications to controller.

Signed-off-by: Krishna Kurapati <krishna.kurapati@oss.qualcomm.com>
---
Link to driver and binding changes:
https://lore.kernel.org/all/20251002172539.586538-1-krishna.kurapati@oss.qualcomm.com/

 arch/arm64/boot/dts/qcom/lemans-evk.dts | 122 +++++++++++++++++++++++-
 1 file changed, 121 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/qcom/lemans-evk.dts b/arch/arm64/boot/dts/qcom/lemans-evk.dts
index c7dc9b8f4457..0b6d8d2d19d6 100644
--- a/arch/arm64/boot/dts/qcom/lemans-evk.dts
+++ b/arch/arm64/boot/dts/qcom/lemans-evk.dts
@@ -37,6 +37,32 @@ chosen {
 		stdout-path = "serial0:115200n8";
 	};
 
+	connector0 {
+		compatible = "usb-c-connector";
+		label = "USB0-Type-C";
+		data-role = "dual";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				usb0_con_hs_ep: endpoint {
+					remote-endpoint = <&usb3_hs_ep>;
+				};
+			};
+			port@1 {
+				reg = <1>;
+
+				usb0_con_ss_ep: endpoint {
+					remote-endpoint = <&hd3ss3220_in_ep>;
+				};
+			};
+		};
+	};
+
 	edp0-connector {
 		compatible = "dp-connector";
 		label = "EDP0";
@@ -101,6 +127,15 @@ platform {
 		};
 	};
 
+	vbus_supply_regulator_0: vbus-supply-regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vbus_supply_0";
+		gpio = <&expander1 2 GPIO_ACTIVE_HIGH>;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+	};
+
 	vmmc_sdc: regulator-vmmc-sdc {
 		compatible = "regulator-fixed";
 
@@ -453,6 +488,55 @@ &gpi_dma2 {
 	status = "okay";
 };
 
+&pmm8654au_2_gpios {
+	usb0_intr_state: usb0-intr-state {
+		pins = "gpio5";
+		function = "normal";
+		input-enable;
+		bias-pull-up;
+		power-source = <0>;
+	};
+};
+
+&i2c11 {
+	status = "okay";
+
+	hd3ss3220@67 {
+		compatible = "ti,hd3ss3220";
+		reg = <0x67>;
+
+		interrupts-extended = <&pmm8654au_2_gpios 5 IRQ_TYPE_EDGE_FALLING>;
+
+		id-gpios = <&tlmm 50 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-0 = <&usb_id>, <&usb0_intr_state>;
+		pinctrl-names = "default";
+
+		vbus-supply = <&vbus_supply_regulator_0>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				hd3ss3220_in_ep: endpoint {
+					remote-endpoint = <&usb0_con_ss_ep>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				hd3ss3220_out_ep: endpoint {
+					remote-endpoint = <&usb3_role_switch>;
+				};
+			};
+		};
+	};
+};
+
 &i2c18 {
 	status = "okay";
 
@@ -718,11 +802,24 @@ wake-pins {
 		};
 	};
 
+	qup_i2c11_default: qup-i2c11-state {
+		pins = "gpio48", "gpio49";
+		function = "qup1_se4";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+
 	sd_cd: sd-cd-state {
 		pins = "gpio36";
 		function = "gpio";
 		bias-pull-up;
 	};
+
+	usb_id: usb-id-state {
+		pins = "gpio50";
+		function = "gpio";
+		bias-pull-up;
+	};
 };
 
 &uart10 {
@@ -751,9 +848,32 @@ &ufs_mem_phy {
 };
 
 &usb_0 {
-	dr_mode = "peripheral";
+	dr_mode = "otg";
+	usb-role-switch;
 
 	status = "okay";
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			usb3_hs_ep: endpoint {
+				remote-endpoint = <&usb0_con_hs_ep>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			usb3_role_switch: endpoint {
+				remote-endpoint = <&hd3ss3220_out_ep>;
+			};
+		};
+
+	};
 };
 
 &usb_0_hsphy {
-- 
2.34.1

Re: [PATCH] arm64: dts: qcom: lemans-evk: Add OTG support for primary USB controller

[Rob Herring (Arm)]

On Thu, 02 Oct 2025 22:59:46 +0530, Krishna Kurapati wrote:
> Enable OTG support for primary USB controller on EVK Platform. Add
> HD3SS3220 Type-C port controller present between Type-C port and SoC
> that provides role switch notifications to controller.
> 
> Signed-off-by: Krishna Kurapati <krishna.kurapati@oss.qualcomm.com>
> ---
> Link to driver and binding changes:
> https://lore.kernel.org/all/20251002172539.586538-1-krishna.kurapati@oss.qualcomm.com/
> 
>  arch/arm64/boot/dts/qcom/lemans-evk.dts | 122 +++++++++++++++++++++++-
>  1 file changed, 121 insertions(+), 1 deletion(-)
> 


My bot found new DTB warnings on the .dts files added or changed in this
series.

Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
are fixed by another series. Ultimately, it is up to the platform
maintainer whether these warnings are acceptable or not. No need to reply
unless the platform maintainer has comments.

If you already ran DT checks and didn't see these error(s), then
make sure dt-schema is up to date:

  pip3 install dtschema --upgrade


This patch series was applied (using b4) to base:
 Base: attempting to guess base-commit...
 Base: remotes/next/fs-next-6496-g155abb6f8812 (exact match)

If this is not the correct base, please add 'base-commit' tag
(or use b4 which does this automatically)

New warnings running 'make CHECK_DTBS=y for arch/arm64/boot/dts/qcom/' for 20251002172946.589061-1-krishna.kurapati@oss.qualcomm.com:

arch/arm64/boot/dts/qcom/lemans-evk.dtb: hd3ss3220@67 (ti,hd3ss3220): 'id-gpios', 'vbus-supply' do not match any of the regexes: '^pinctrl-[0-9]+$'
	from schema $id: http://devicetree.org/schemas/usb/ti,hd3ss3220.yaml#

Re: [PATCH] arm64: dts: qcom: lemans-evk: Add OTG support for primary USB controller

[Konrad Dybcio]

On 10/2/25 7:29 PM, Krishna Kurapati wrote:
> Enable OTG support for primary USB controller on EVK Platform. Add
> HD3SS3220 Type-C port controller present between Type-C port and SoC
> that provides role switch notifications to controller.
> 
> Signed-off-by: Krishna Kurapati <krishna.kurapati@oss.qualcomm.com>
> ---
> Link to driver and binding changes:
> https://lore.kernel.org/all/20251002172539.586538-1-krishna.kurapati@oss.qualcomm.com/
> 
>  arch/arm64/boot/dts/qcom/lemans-evk.dts | 122 +++++++++++++++++++++++-
>  1 file changed, 121 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/lemans-evk.dts b/arch/arm64/boot/dts/qcom/lemans-evk.dts
> index c7dc9b8f4457..0b6d8d2d19d6 100644
> --- a/arch/arm64/boot/dts/qcom/lemans-evk.dts
> +++ b/arch/arm64/boot/dts/qcom/lemans-evk.dts
> @@ -37,6 +37,32 @@ chosen {
>  		stdout-path = "serial0:115200n8";
>  	};
>  
> +	connector0 {
> +		compatible = "usb-c-connector";
> +		label = "USB0-Type-C";

Are there other, non-type-C ports labeled USB0 onboard?

> +		data-role = "dual";

power-role = "xxx"

[...]

> +	vbus_supply_regulator_0: vbus-supply-regulator-0 {

the suffix suggests there are going to be more - is that the case?

[...]

>  &usb_0 {
> -	dr_mode = "peripheral";
> +	dr_mode = "otg";

otg is default, you can probably drop it

Konrad

Re: [PATCH] arm64: dts: qcom: lemans-evk: Add OTG support for primary USB controller

[Krishna Kurapati PSSNV]

On 10/3/2025 6:57 PM, Konrad Dybcio wrote:
> On 10/2/25 7:29 PM, Krishna Kurapati wrote:
>> Enable OTG support for primary USB controller on EVK Platform. Add
>> HD3SS3220 Type-C port controller present between Type-C port and SoC
>> that provides role switch notifications to controller.
>>
>> Signed-off-by: Krishna Kurapati <krishna.kurapati@oss.qualcomm.com>
>> ---
>> Link to driver and binding changes:
>> https://lore.kernel.org/all/20251002172539.586538-1-krishna.kurapati@oss.qualcomm.com/
>>
>>   arch/arm64/boot/dts/qcom/lemans-evk.dts | 122 +++++++++++++++++++++++-
>>   1 file changed, 121 insertions(+), 1 deletion(-)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/lemans-evk.dts b/arch/arm64/boot/dts/qcom/lemans-evk.dts
>> index c7dc9b8f4457..0b6d8d2d19d6 100644
>> --- a/arch/arm64/boot/dts/qcom/lemans-evk.dts
>> +++ b/arch/arm64/boot/dts/qcom/lemans-evk.dts
>> @@ -37,6 +37,32 @@ chosen {
>>   		stdout-path = "serial0:115200n8";
>>   	};
>>   
>> +	connector0 {
>> +		compatible = "usb-c-connector";
>> +		label = "USB0-Type-C";
> 
> Are there other, non-type-C ports labeled USB0 onboard?
> 

There is another Type-C port connected to secondary controller.
There is one Micro USB Port connected to tertiary controller.

>> +		data-role = "dual";
> 
> power-role = "xxx"
> 

ACK. Will add it.

> [...]
> 
>> +	vbus_supply_regulator_0: vbus-supply-regulator-0 {
> 
> the suffix suggests there are going to be more - is that the case?
> 

The second Typec port would have another connector added. So another 
vbus node would be added.

> [...]
> 
>>   &usb_0 {
>> -	dr_mode = "peripheral";
>> +	dr_mode = "otg";
> 
> otg is default, you can probably drop it
> 

ACK.

Regards,
Krishna,