[PATCH v8 0/5] media: iris: add support for purwa platform

[PATCH v8 0/5] media: iris: add support for purwa platform

[Wangao Wang]

This series enables the Iris video codec on purwa, allowing purwa to
use hardware‑accelerated video encoding and decoding.

The Iris codec on purwa is nearly identical to the one on hamoa(X1E),
except that it requires one additional clock and uses a different OPP
table.

Therefore, purwa can reuse the Iris node from hamoa, but the clocks
and OPP table need to be redefined.

All patches have been tested with v4l2-compliance and v4l2-ctl on
purwa. And it does not affect existing targets.

Dependencies:
https://lore.kernel.org/all/20260409-purwa-videocc-camcc-v4-0-5a8e5f2dd4b2@oss.qualcomm.com/

The result of v4l2-compliance on purwa:
v4l2-compliance 1.31.0-5379, 64 bits, 64-bit time_t
v4l2-compliance SHA: 14c988631ad4 2025-11-11 11:19:35

Compliance test for iris_driver device /dev/video0:

Driver Info:
        Driver name      : iris_driver
        Card type        : Iris Decoder
        Bus info         : platform:aa00000.video-codec
        Driver version   : 6.19.0
        Capabilities     : 0x84204000
                Video Memory-to-Memory Multiplanar
                Streaming
                Extended Pix Format
                Device Capabilities
        Device Caps      : 0x04204000
                Video Memory-to-Memory Multiplanar
                Streaming
                Extended Pix Format
        Detected Stateful Decoder

Required ioctls:
        test VIDIOC_QUERYCAP: OK
        test invalid ioctls: OK

Allow for multiple opens:
        test second /dev/video0 open: OK
        test VIDIOC_QUERYCAP: OK
        test VIDIOC_G/S_PRIORITY: OK
        test for unlimited opens: OK

Debug ioctls:
        test VIDIOC_DBG_G/S_REGISTER: OK (Not Supported)
        test VIDIOC_LOG_STATUS: OK (Not Supported)

Input ioctls:
        test VIDIOC_G/S_TUNER/ENUM_FREQ_BANDS: OK (Not Supported)
        test VIDIOC_G/S_FREQUENCY: OK (Not Supported)
        test VIDIOC_S_HW_FREQ_SEEK: OK (Not Supported)
        test VIDIOC_ENUMAUDIO: OK (Not Supported)
        test VIDIOC_G/S/ENUMINPUT: OK (Not Supported)
        test VIDIOC_G/S_AUDIO: OK (Not Supported)
        Inputs: 0 Audio Inputs: 0 Tuners: 0

Output ioctls:
        test VIDIOC_G/S_MODULATOR: OK (Not Supported)
        test VIDIOC_G/S_FREQUENCY: OK (Not Supported)
        test VIDIOC_ENUMAUDOUT: OK (Not Supported)
        test VIDIOC_G/S/ENUMOUTPUT: OK (Not Supported)
        test VIDIOC_G/S_AUDOUT: OK (Not Supported)
        Outputs: 0 Audio Outputs: 0 Modulators: 0

Input/Output configuration ioctls:
        test VIDIOC_ENUM/G/S/QUERY_STD: OK (Not Supported)
        test VIDIOC_ENUM/G/S/QUERY_DV_TIMINGS: OK (Not Supported)
        test VIDIOC_DV_TIMINGS_CAP: OK (Not Supported)
        test VIDIOC_G/S_EDID: OK (Not Supported)

Control ioctls:
        test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: OK
        test VIDIOC_QUERYCTRL: OK
        test VIDIOC_G/S_CTRL: OK
        test VIDIOC_G/S/TRY_EXT_CTRLS: OK
        test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: OK
        test VIDIOC_G/S_JPEGCOMP: OK (Not Supported)
        Standard Controls: 10 Private Controls: 0

Format ioctls:
        test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK
        test VIDIOC_G/S_PARM: OK (Not Supported)
        test VIDIOC_G_FBUF: OK (Not Supported)
        test VIDIOC_G_FMT: OK
        test VIDIOC_TRY_FMT: OK
        test VIDIOC_S_FMT: OK
        test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported)
        test Cropping: OK
        test Composing: OK
        test Scaling: OK (Not Supported)

Codec ioctls:
        test VIDIOC_(TRY_)ENCODER_CMD: OK (Not Supported)
        test VIDIOC_G_ENC_INDEX: OK (Not Supported)
        test VIDIOC_(TRY_)DECODER_CMD: OK

Buffer ioctls:
        test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK
        test CREATE_BUFS maximum buffers: OK
        test VIDIOC_REMOVE_BUFS: OK
        test VIDIOC_EXPBUF: OK
        test Requests: OK (Not Supported)
        test blocking wait: OK

Test input 0:

Streaming ioctls:
        test read/write: OK (Not Supported)
the input file is smaller than 7077888 bytes
        Video Capture Multiplanar: Captured 65 buffers
        test MMAP (select, REQBUFS): OK
the input file is smaller than 7077888 bytes
        Video Capture Multiplanar: Captured 65 buffers
        test MMAP (epoll, REQBUFS): OK
the input file is smaller than 7077888 bytes
        Video Capture Multiplanar: Captured 65 buffers
        test MMAP (select, CREATE_BUFS): OK
the input file is smaller than 7077888 bytes
        Video Capture Multiplanar: Captured 65 buffers
        test MMAP (epoll, CREATE_BUFS): OK
        test USERPTR (select): OK (Not Supported)
        test DMABUF: Cannot test, specify --expbuf-device

Total for iris_driver device /dev/video0: 54, Succeeded: 54, Failed: 0, Warnings: 0
root@localhost:/lib/video_test# ./v4l2-compliance -d /dev/video1 -s
v4l2-compliance 1.31.0-5379, 64 bits, 64-bit time_t
v4l2-compliance SHA: 14c988631ad4 2025-11-11 11:19:35

Compliance test for iris_driver device /dev/video1:

Driver Info:
        Driver name      : iris_driver
        Card type        : Iris Encoder
        Bus info         : platform:aa00000.video-codec
        Driver version   : 6.19.0
        Capabilities     : 0x84204000
                Video Memory-to-Memory Multiplanar
                Streaming
                Extended Pix Format
                Device Capabilities
        Device Caps      : 0x04204000
                Video Memory-to-Memory Multiplanar
                Streaming
                Extended Pix Format
        Detected Stateful Encoder

Required ioctls:
        test VIDIOC_QUERYCAP: OK
        test invalid ioctls: OK

Allow for multiple opens:
        test second /dev/video1 open: OK
        test VIDIOC_QUERYCAP: OK
        test VIDIOC_G/S_PRIORITY: OK
        test for unlimited opens: OK

Debug ioctls:
        test VIDIOC_DBG_G/S_REGISTER: OK (Not Supported)
        test VIDIOC_LOG_STATUS: OK (Not Supported)

Input ioctls:
        test VIDIOC_G/S_TUNER/ENUM_FREQ_BANDS: OK (Not Supported)
        test VIDIOC_G/S_FREQUENCY: OK (Not Supported)
        test VIDIOC_S_HW_FREQ_SEEK: OK (Not Supported)
        test VIDIOC_ENUMAUDIO: OK (Not Supported)
        test VIDIOC_G/S/ENUMINPUT: OK (Not Supported)
        test VIDIOC_G/S_AUDIO: OK (Not Supported)
        Inputs: 0 Audio Inputs: 0 Tuners: 0

Output ioctls:
        test VIDIOC_G/S_MODULATOR: OK (Not Supported)
        test VIDIOC_G/S_FREQUENCY: OK (Not Supported)
        test VIDIOC_ENUMAUDOUT: OK (Not Supported)
        test VIDIOC_G/S/ENUMOUTPUT: OK (Not Supported)
        test VIDIOC_G/S_AUDOUT: OK (Not Supported)
        Outputs: 0 Audio Outputs: 0 Modulators: 0

Input/Output configuration ioctls:
        test VIDIOC_ENUM/G/S/QUERY_STD: OK (Not Supported)
        test VIDIOC_ENUM/G/S/QUERY_DV_TIMINGS: OK (Not Supported)
        test VIDIOC_DV_TIMINGS_CAP: OK (Not Supported)
        test VIDIOC_G/S_EDID: OK (Not Supported)

Control ioctls:
        test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: OK
        test VIDIOC_QUERYCTRL: OK
        test VIDIOC_G/S_CTRL: OK
        test VIDIOC_G/S/TRY_EXT_CTRLS: OK
        test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: OK
        test VIDIOC_G/S_JPEGCOMP: OK (Not Supported)
        Standard Controls: 38 Private Controls: 0

Format ioctls:
        test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK
        test VIDIOC_G/S_PARM: OK
        test VIDIOC_G_FBUF: OK (Not Supported)
        test VIDIOC_G_FMT: OK
        test VIDIOC_TRY_FMT: OK
        test VIDIOC_S_FMT: OK
        test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported)
        test Cropping: OK
        test Composing: OK (Not Supported)
        test Scaling: OK (Not Supported)

Codec ioctls:
        test VIDIOC_(TRY_)ENCODER_CMD: OK
        test VIDIOC_G_ENC_INDEX: OK (Not Supported)
        test VIDIOC_(TRY_)DECODER_CMD: OK (Not Supported)

Buffer ioctls:
        test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK
        test CREATE_BUFS maximum buffers: OK
        test VIDIOC_REMOVE_BUFS: OK
        test VIDIOC_EXPBUF: OK
        test Requests: OK (Not Supported)
        test blocking wait: OK

Test input 0:

Streaming ioctls:
        test read/write: OK (Not Supported)
        Video Capture Multiplanar: Captured 61 buffers
        test MMAP (select, REQBUFS): OK
        Video Capture Multiplanar: Captured 61 buffers
        test MMAP (epoll, REQBUFS): OK
        Video Capture Multiplanar: Captured 61 buffers
        test MMAP (select, CREATE_BUFS): OK
        Video Capture Multiplanar: Captured 61 buffers
        test MMAP (epoll, CREATE_BUFS): OK
        test USERPTR (select): OK (Not Supported)
        test DMABUF: Cannot test, specify --expbuf-device

Total for iris_driver device /dev/video1: 54, Succeeded: 54, Failed: 0, Warnings: 0

fluster result:
H.264:
Ran 77/135 tests successfully

H.265:
Ran 131/147 tests successfully

VP9:
Ran 235/305 tests successfully

Signed-off-by: Wangao Wang <wangao.wang@oss.qualcomm.com>
---
Changes in v8:
- Rebase onto the media-committers venus-iris-next branch.
- Link to v7: https://lore.kernel.org/r/20260514-enable_iris_on_purwa-v7-0-47aa5b026f1a@oss.qualcomm.com

Changes in v7:
- Rebase onto the media-committers next+fixes branch.
- Correct the firmware name.
- Link to v6: https://lore.kernel.org/r/20260507-enable_iris_on_purwa-v6-0-48da505e23bf@oss.qualcomm.com

Changes in v6:
- Correct the firmware being used.(Dikshita)
- Add comments to platform data.(Dikshita)
- Link to v5: https://lore.kernel.org/r/20260429-enable_iris_on_purwa-v5-0-438fa96da248@oss.qualcomm.com

Changes in v5:
- Modify the dt-binding description.(Krzysztof)
- Move the BSE clock on/off handling into the vpu3 code.(Krzysztof)
- Link to v4: https://lore.kernel.org/r/20260401-enable_iris_on_purwa-v4-0-ca784552a3e9@oss.qualcomm.com

Changes in v4:
- Correct the dt-binding description.(Krzysztof)
- Fix incorrect required-opps.(Dmitry)
- Reuse the vpu3 power off hardware api.
- Link to v3: https://lore.kernel.org/r/20260319-enable_iris_on_purwa-v3-0-bf8f3e9a8c9c@oss.qualcomm.com

Changes in v3:
- Correct the dt-binding description.(Krzysztof)
- Fix warnings reported in the patch.(Krzysztof)
- Add separate power on/off hooks for Purwa.(Dmitry)
- Link to v2: https://lore.kernel.org/r/20260306-enable_iris_on_purwa-v2-0-75fa80a0a9e3@oss.qualcomm.com

Changes in v2:
- Improve the dt-binding description.(Krzysztof)
- Move the BSE clock on/off handling into the vpu3 code.(Dmitry)
- Add the required members to the platform data for Purwa.(Dikshita)
- Link to v1: https://lore.kernel.org/r/20260209-enable_iris_on_purwa-v1-0-537c410f604f@oss.qualcomm.com

---
Wangao Wang (5):
      dt-bindings: media: qcom,sm8550-iris: Add X1P42100 compatible
      media: iris: Add hardware power on/off ops for X1P42100
      media: iris: Add platform data for X1P42100
      arm64: dts: qcom: purwa: Override Iris clocks and operating points
      arm64: dts: qcom: purwa-iot-som: enable video

 .../bindings/media/qcom,sm8550-iris.yaml           | 23 +++++++++-
 arch/arm64/boot/dts/qcom/purwa-iot-som.dtsi        |  4 ++
 arch/arm64/boot/dts/qcom/purwa.dtsi                | 50 ++++++++++++++++++++++
 .../platform/qcom/iris/iris_platform_common.h      |  1 +
 .../media/platform/qcom/iris/iris_platform_vpu3x.c | 42 ++++++++++++++++++
 .../platform/qcom/iris/iris_platform_x1p42100.h    | 22 ++++++++++
 drivers/media/platform/qcom/iris/iris_probe.c      |  4 ++
 drivers/media/platform/qcom/iris/iris_vpu_common.c |  9 +++-
 8 files changed, 153 insertions(+), 2 deletions(-)
---
base-commit: 735d2f48cadaa9a87e7c7601667878de70c771c5
change-id: 20260209-enable_iris_on_purwa-a000527a098d
prerequisite-change-id: 20260331-purwa-videocc-camcc-d9700d0f797d:v4
prerequisite-patch-id: 61bdb45446193b72dd8a4b093e4ab2f78db2f066
prerequisite-patch-id: b5be9dcbb612a14108f890b2782860847edfcbe4
prerequisite-patch-id: 2f4d4c5c118e057c76e6d2785479df01d5bc1c7b
prerequisite-patch-id: 026db5dd71d5b0472225ba72c8ba2781334143a9
prerequisite-patch-id: 615e6f38e528de35dc206f1c7f3eaf78ff04afe2
prerequisite-patch-id: 66096b909debe4d942eee972948d5a138a5be427
prerequisite-patch-id: ee26e00cdde21ddb070af713230082ad3454422c

Best regards,
-- 
Wangao Wang <wangao.wang@oss.qualcomm.com>

[PATCH v8 1/5] dt-bindings: media: qcom,sm8550-iris: Add X1P42100 compatible

[Wangao Wang]

Document the new compatible string "qcom,x1p42100-iris".

Unlike SM8550 where the BSE (Bitstream Engine) is clocked implicitly
via vcodec0_core, x1p42100 exposes a dedicated BSE clock vcodec0_bse
that requires explicit enable/disable and frequency configuration.
The SM8550 driver has no knowledge of this clock and therefore cannot
operate x1p42100 hardware correctly.

Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Wangao Wang <wangao.wang@oss.qualcomm.com>
---
 .../bindings/media/qcom,sm8550-iris.yaml           | 23 +++++++++++++++++++++-
 1 file changed, 22 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/media/qcom,sm8550-iris.yaml b/Documentation/devicetree/bindings/media/qcom,sm8550-iris.yaml
index 9c4b760508b50251ac467ad44a366689260bfc0d..0400ca1bff05dcef6b742c3fbf77e38adca9f280 100644
--- a/Documentation/devicetree/bindings/media/qcom,sm8550-iris.yaml
+++ b/Documentation/devicetree/bindings/media/qcom,sm8550-iris.yaml
@@ -26,6 +26,7 @@ properties:
           - qcom,qcs8300-iris
           - qcom,sm8550-iris
           - qcom,sm8650-iris
+          - qcom,x1p42100-iris
 
   reg:
     maxItems: 1
@@ -41,13 +42,16 @@ properties:
       - const: mmcx
 
   clocks:
-    maxItems: 3
+    minItems: 3
+    maxItems: 4
 
   clock-names:
+    minItems: 3
     items:
       - const: iface
       - const: core
       - const: vcodec0_core
+      - const: vcodec0_bse
 
   firmware-name:
     maxItems: 1
@@ -115,6 +119,23 @@ allOf:
           maxItems: 1
         reset-names:
           maxItems: 1
+  - if:
+      properties:
+        compatible:
+          enum:
+            - qcom,x1p42100-iris
+    then:
+      properties:
+        clocks:
+          minItems: 4
+        clock-names:
+          minItems: 4
+    else:
+      properties:
+        clocks:
+          maxItems: 3
+        clock-names:
+          maxItems: 3
 
 unevaluatedProperties: false
 

-- 
2.43.0

[PATCH v8 2/5] media: iris: Add hardware power on/off ops for X1P42100

[Wangao Wang]

On X1P42100 the Iris block has an extra BSE clock. Wire this clock into
the power on/off sequence.

The BSE clock is used to drive the Bin Stream Engine, which is a sub-block
of the video codec hardware responsible for bitstream-level processing. It
is required to be enabled separately from the core clock to ensure proper
codec operation.

Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Dikshita Agarwal <dikshita.agarwal@oss.qualcomm.com>
Signed-off-by: Wangao Wang <wangao.wang@oss.qualcomm.com>
---
 drivers/media/platform/qcom/iris/iris_vpu_common.c | 9 ++++++++-
 1 file changed, 8 insertions(+), 1 deletion(-)

diff --git a/drivers/media/platform/qcom/iris/iris_vpu_common.c b/drivers/media/platform/qcom/iris/iris_vpu_common.c
index 3872c4f37987ebbddbb040722adaa252faa40a73..5a85568c5ee1c5b656131607e7aef1b8a75e020d 100644
--- a/drivers/media/platform/qcom/iris/iris_vpu_common.c
+++ b/drivers/media/platform/qcom/iris/iris_vpu_common.c
@@ -224,6 +224,7 @@ void iris_vpu_power_off_hw(struct iris_core *core)
 {
 	dev_pm_genpd_set_hwmode(core->pmdomain_tbl->pd_devs[IRIS_HW_POWER_DOMAIN], false);
 	iris_disable_power_domains(core, core->pmdomain_tbl->pd_devs[IRIS_HW_POWER_DOMAIN]);
+	iris_disable_unprepare_clock(core, IRIS_BSE_HW_CLK);
 	iris_disable_unprepare_clock(core, IRIS_HW_AHB_CLK);
 	iris_disable_unprepare_clock(core, IRIS_HW_CLK);
 }
@@ -292,12 +293,18 @@ int iris_vpu_power_on_hw(struct iris_core *core)
 	if (ret && ret != -ENOENT)
 		goto err_disable_hw_clock;
 
+	ret = iris_prepare_enable_clock(core, IRIS_BSE_HW_CLK);
+	if (ret && ret != -ENOENT)
+		goto err_disable_hw_ahb_clock;
+
 	ret = dev_pm_genpd_set_hwmode(core->pmdomain_tbl->pd_devs[IRIS_HW_POWER_DOMAIN], true);
 	if (ret)
-		goto err_disable_hw_ahb_clock;
+		goto err_disable_bse_hw_clock;
 
 	return 0;
 
+err_disable_bse_hw_clock:
+	iris_disable_unprepare_clock(core, IRIS_BSE_HW_CLK);
 err_disable_hw_ahb_clock:
 	iris_disable_unprepare_clock(core, IRIS_HW_AHB_CLK);
 err_disable_hw_clock:

-- 
2.43.0

[PATCH v8 3/5] media: iris: Add platform data for X1P42100

[Wangao Wang]

Introduce platform data for X1P42100, derived from SM8550 but using a
different clock configuration and a dedicated OPP setup.

Reviewed-by: Vikash Garodia <vikash.garodia@oss.qualcomm.com>
Signed-off-by: Wangao Wang <wangao.wang@oss.qualcomm.com>
---
 .../platform/qcom/iris/iris_platform_common.h      |  1 +
 .../media/platform/qcom/iris/iris_platform_vpu3x.c | 42 ++++++++++++++++++++++
 .../platform/qcom/iris/iris_platform_x1p42100.h    | 22 ++++++++++++
 drivers/media/platform/qcom/iris/iris_probe.c      |  4 +++
 4 files changed, 69 insertions(+)

diff --git a/drivers/media/platform/qcom/iris/iris_platform_common.h b/drivers/media/platform/qcom/iris/iris_platform_common.h
index 972fd4dd021cda6359cc84c444e2a77f41ab7ddb..8201c4723ed16c6440eb95c6ea623ae9af4e3cc5 100644
--- a/drivers/media/platform/qcom/iris/iris_platform_common.h
+++ b/drivers/media/platform/qcom/iris/iris_platform_common.h
@@ -59,6 +59,7 @@ extern const struct iris_platform_data sm8250_data;
 extern const struct iris_platform_data sm8550_data;
 extern const struct iris_platform_data sm8650_data;
 extern const struct iris_platform_data sm8750_data;
+extern const struct iris_platform_data x1p42100_data;
 
 enum platform_clk_type {
 	IRIS_AXI_CLK, /* AXI0 in case of platforms with multiple AXI clocks */
diff --git a/drivers/media/platform/qcom/iris/iris_platform_vpu3x.c b/drivers/media/platform/qcom/iris/iris_platform_vpu3x.c
index c249ff8275414a355339ec8edb6856f292b5cff2..541ddc40e3aeef349f1ae68e216d398b3b4fba78 100644
--- a/drivers/media/platform/qcom/iris/iris_platform_vpu3x.c
+++ b/drivers/media/platform/qcom/iris/iris_platform_vpu3x.c
@@ -16,6 +16,7 @@
 #include "iris_platform_sm8550.h"
 #include "iris_platform_sm8650.h"
 #include "iris_platform_sm8750.h"
+#include "iris_platform_x1p42100.h"
 
 static const struct iris_firmware_desc iris_vpu30_p4_s6_gen2_desc = {
 	.firmware_data = &iris_hfi_gen2_data,
@@ -29,6 +30,12 @@ static const struct iris_firmware_desc iris_vpu30_p4_gen2_desc = {
 	.fwname = "qcom/vpu/vpu30_p4.mbn",
 };
 
+static const struct iris_firmware_desc iris_vpu30_p1_gen2_desc = {
+	.firmware_data = &iris_hfi_gen2_data,
+	.get_vpu_buffer_size = iris_vpu_buf_size,
+	.fwname = "qcom/vpu/vpu30_p1_s7.mbn",
+};
+
 static const struct iris_firmware_desc iris_vpu33_p4_gen2_desc = {
 	.firmware_data = &iris_hfi_gen2_data,
 	.get_vpu_buffer_size = iris_vpu33_buf_size,
@@ -217,3 +224,38 @@ const struct iris_platform_data sm8750_data = {
 	.max_core_mbpf = NUM_MBS_8K * 2,
 	.max_core_mbps = ((7680 * 4320) / 256) * 60,
 };
+
+/*
+ * Shares most of SM8550 data except:
+ * - clk_tbl and opp_clk_tbl for x1p42100
+ * - different firmware
+ * - different num_vpp_pipe
+ */
+const struct iris_platform_data x1p42100_data = {
+	.firmware_desc = &iris_vpu30_p1_gen2_desc,
+	.vpu_ops = &iris_vpu3_ops,
+	.icc_tbl = iris_icc_info_vpu3x,
+	.icc_tbl_size = ARRAY_SIZE(iris_icc_info_vpu3x),
+	.clk_rst_tbl = sm8550_clk_reset_table,
+	.clk_rst_tbl_size = ARRAY_SIZE(sm8550_clk_reset_table),
+	.bw_tbl_dec = iris_bw_table_dec_vpu3x,
+	.bw_tbl_dec_size = ARRAY_SIZE(iris_bw_table_dec_vpu3x),
+	.pmdomain_tbl = iris_pmdomain_table_vpu3x,
+	.pmdomain_tbl_size = ARRAY_SIZE(iris_pmdomain_table_vpu3x),
+	.opp_pd_tbl = iris_opp_pd_table_vpu3x,
+	.opp_pd_tbl_size = ARRAY_SIZE(iris_opp_pd_table_vpu3x),
+	.clk_tbl = x1p42100_clk_table,
+	.clk_tbl_size = ARRAY_SIZE(x1p42100_clk_table),
+	.opp_clk_tbl = x1p42100_opp_clk_table,
+	/* Upper bound of DMA address range */
+	.dma_mask = 0xe0000000 - 1,
+	.inst_iris_fmts = iris_fmts_vpu3x_dec,
+	.inst_iris_fmts_size = ARRAY_SIZE(iris_fmts_vpu3x_dec),
+	.inst_caps = &platform_inst_cap_sm8550,
+	.tz_cp_config_data = tz_cp_config_vpu3,
+	.tz_cp_config_data_size = ARRAY_SIZE(tz_cp_config_vpu3),
+	.num_vpp_pipe = 1,
+	.max_session_count = 16,
+	.max_core_mbpf = NUM_MBS_8K * 2,
+	.max_core_mbps = ((7680 * 4320) / 256) * 60,
+};
diff --git a/drivers/media/platform/qcom/iris/iris_platform_x1p42100.h b/drivers/media/platform/qcom/iris/iris_platform_x1p42100.h
new file mode 100644
index 0000000000000000000000000000000000000000..d89acfbc1233dad0692f6c13c3fc22b10e5bdd80
--- /dev/null
+++ b/drivers/media/platform/qcom/iris/iris_platform_x1p42100.h
@@ -0,0 +1,22 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+#ifndef __IRIS_PLATFORM_X1P42100_H__
+#define __IRIS_PLATFORM_X1P42100_H__
+
+static const struct platform_clk_data x1p42100_clk_table[] = {
+	{IRIS_AXI_CLK,		"iface"			},
+	{IRIS_CTRL_CLK,		"core"			},
+	{IRIS_HW_CLK,		"vcodec0_core"		},
+	{IRIS_BSE_HW_CLK,	"vcodec0_bse"		},
+};
+
+static const char *const x1p42100_opp_clk_table[] = {
+	"vcodec0_core",
+	"vcodec0_bse",
+	NULL,
+};
+
+#endif
diff --git a/drivers/media/platform/qcom/iris/iris_probe.c b/drivers/media/platform/qcom/iris/iris_probe.c
index d36f0c0e785b7de0e3527e0a824942db0fb79133..9f8113ec7a508a5a26cf275408165d34684d3e0b 100644
--- a/drivers/media/platform/qcom/iris/iris_probe.c
+++ b/drivers/media/platform/qcom/iris/iris_probe.c
@@ -385,6 +385,10 @@ static const struct of_device_id iris_dt_match[] = {
 		.compatible = "qcom,sm8750-iris",
 		.data = &sm8750_data,
 	},
+	{
+		.compatible = "qcom,x1p42100-iris",
+		.data = &x1p42100_data,
+	},
 	{ },
 };
 MODULE_DEVICE_TABLE(of, iris_dt_match);

-- 
2.43.0

[PATCH v8 4/5] arm64: dts: qcom: purwa: Override Iris clocks and operating points

[Wangao Wang]

The Iris block on X1P differs from SM8550/X1E in its clock configuration
and requires a dedicated OPP table. The node inherited from the X1E cannot
be reused directly, and the fallback compatible "qcom,sm8550-iris" cannot
be applied.

Override the inherited clocks, clock-names, and operating points, and
replaces them with the X1P42100-specific definitions. A new OPP table
is provided to support the correct performance levels on this platform.

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dikshita Agarwal <dikshita.agarwal@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Wangao Wang <wangao.wang@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/purwa.dtsi | 50 +++++++++++++++++++++++++++++++++++++
 1 file changed, 50 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/purwa.dtsi b/arch/arm64/boot/dts/qcom/purwa.dtsi
index ea65b8448836ead83f837e973ed536e8ea0ed8ef..a503deec97d75dcfb6792b007e0b74e517404cfc 100644
--- a/arch/arm64/boot/dts/qcom/purwa.dtsi
+++ b/arch/arm64/boot/dts/qcom/purwa.dtsi
@@ -21,6 +21,7 @@
 /delete-node/ &cpu_pd11;
 /delete-node/ &gpu_opp_table;
 /delete-node/ &gpu_speed_bin;
+/delete-node/ &iris_opp_table;
 /delete-node/ &pcie3_phy;
 /delete-node/ &thermal_aoss3;
 /delete-node/ &thermal_cpu2_0_btm;
@@ -167,6 +168,55 @@ &gpucc {
 	compatible = "qcom,x1p42100-gpucc";
 };
 
+&iris {
+	compatible = "qcom,x1p42100-iris";
+
+	clocks = <&gcc GCC_VIDEO_AXI0_CLK>,
+		 <&videocc VIDEO_CC_MVS0C_CLK>,
+		 <&videocc VIDEO_CC_MVS0_CLK>,
+		 <&videocc VIDEO_CC_MVS0_BSE_CLK>;
+	clock-names = "iface",
+		      "core",
+		      "vcodec0_core",
+		      "vcodec0_bse";
+
+	operating-points-v2 = <&iris_opp_table_x1p42100>;
+
+	iris_opp_table_x1p42100: opp-table {
+		compatible = "operating-points-v2";
+
+		opp-210000000 {
+			opp-hz = /bits/ 64 <210000000 105000000>;
+			required-opps = <&rpmhpd_opp_low_svs_d1>,
+					<&rpmhpd_opp_low_svs>;
+		};
+
+		opp-300000000 {
+			opp-hz = /bits/ 64 <300000000 150000000>;
+			required-opps = <&rpmhpd_opp_low_svs_d1>,
+					<&rpmhpd_opp_svs>;
+		};
+
+		opp-335000000 {
+			opp-hz = /bits/ 64 <335000000 167500000>;
+			required-opps = <&rpmhpd_opp_svs>,
+					<&rpmhpd_opp_svs_l1>;
+		};
+
+		opp-424000000 {
+			opp-hz = /bits/ 64 <424000000 212000000>;
+			required-opps = <&rpmhpd_opp_svs>,
+					<&rpmhpd_opp_nom>;
+		};
+
+		opp-500000000 {
+			opp-hz = /bits/ 64 <500000000 250000000>;
+			required-opps = <&rpmhpd_opp_svs>,
+					<&rpmhpd_opp_turbo>;
+		};
+	};
+};
+
 /* PCIe3 has half the lanes compared to X1E80100 */
 &pcie3 {
 	num-lanes = <4>;

-- 
2.43.0

[PATCH v8 5/5] arm64: dts: qcom: purwa-iot-som: enable video

[Wangao Wang]

Enable video nodes on the purwa-iot-som board.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Dikshita Agarwal <dikshita.agarwal@oss.qualcomm.com>
Signed-off-by: Wangao Wang <wangao.wang@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/purwa-iot-som.dtsi | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/purwa-iot-som.dtsi b/arch/arm64/boot/dts/qcom/purwa-iot-som.dtsi
index 394e65518ac5037e5c7c50583acefc0dbc8ebb47..ff8621f8750584636ad781467f9c35ace2354e4c 100644
--- a/arch/arm64/boot/dts/qcom/purwa-iot-som.dtsi
+++ b/arch/arm64/boot/dts/qcom/purwa-iot-som.dtsi
@@ -389,6 +389,10 @@ &gpu_zap_shader {
 	firmware-name = "qcom/x1p42100/gen71500_zap.mbn";
 };
 
+&iris {
+	status = "okay";
+};
+
 &pcie3 {
 	pinctrl-0 = <&pcie3_default>;
 	pinctrl-names = "default";

-- 
2.43.0

Re: [PATCH v8 1/5] dt-bindings: media: qcom,sm8550-iris: Add X1P42100 compatible

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 2 potential issue(s) to consider:
- [Medium] Missing required properties in the conditional block for `qcom,x1p42100-iris` allows incomplete device tree nodes to pass validation.
- [Medium] Broken schema conditional matching for `qcom,x1p42100-iris` causes valid device tree nodes to fail validation.
--

commit f911896de9da99ee2b5652949237c15bf6d78f44
Author: Wangao Wang <wangao.wang@oss.qualcomm.com>

dt-bindings: media: qcom,sm8550-iris: Add X1P42100 compatible

Document the new compatible string "qcom,x1p42100-iris". Unlike SM8550 where
the BSE is clocked implicitly, x1p42100 exposes a dedicated BSE clock that
requires explicit configuration.

> diff --git a/Documentation/devicetree/bindings/media/qcom,sm8550-iris.yaml b/Documentation/devicetree/bindings/media/qcom,sm8550-iris.yaml
> index 9c4b760508b50..0400ca1bff05d 100644
> --- a/Documentation/devicetree/bindings/media/qcom,sm8550-iris.yaml
> +++ b/Documentation/devicetree/bindings/media/qcom,sm8550-iris.yaml

[ ... ]

> @@ -115,6 +119,23 @@ allOf:
>            maxItems: 1
>          reset-names:
>            maxItems: 1
> +  - if:
> +      properties:
> +        compatible:
> +          enum:
> +            - qcom,x1p42100-iris

[Severity: Medium]
Should this use "contains: enum" or "contains: const" instead of a direct
enum match?

Since the compatible property is evaluated as an array of strings in device
tree validation, a direct enum match will fail against an array. This could
cause the condition to always evaluate to false, falling through to the else
block which restricts clocks to maxItems: 3, causing correctly configured
nodes to fail validation.

> +    then:
> +      properties:
> +        clocks:
> +          minItems: 4
> +        clock-names:
> +          minItems: 4

[Severity: Medium]
Since minItems constraints only apply if the property is actually present,
should clocks and clock-names be added to a required list in this block?

Without them, a device tree node omitting the clocks entirely might silently
pass schema validation, even though the fourth clock is mandatory for this
variant to operate.

> +    else:
> +      properties:
> +        clocks:
> +          maxItems: 3
> +        clock-names:
> +          maxItems: 3

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20260529-enable_iris_on_purwa-v8-0-b1b9670459ab@oss.qualcomm.com?part=1

Re: [PATCH v8 2/5] media: iris: Add hardware power on/off ops for X1P42100

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider:

Pre-existing issues:
- [High] Incorrect teardown ordering in `iris_vpu_power_off_hw()` disables power domains before hardware clocks.
--

commit 99a4b6ceed030f2e0c99e6828095cd2e45157242
Author: Wangao Wang <wangao.wang@oss.qualcomm.com>

media: iris: Add hardware power on/off ops for X1P42100

This commit wires an extra BSE clock into the power on/off sequence for
the Iris block on the X1P42100 platform. The BSE clock drives the Bin
Stream Engine and is required to be enabled separately from the core clock.

> diff --git a/drivers/media/platform/qcom/iris/iris_vpu_common.c b/drivers/media/platform/qcom/iris/iris_vpu_common.c
> index c6cfc1d9fd9ec..a3238bf118eb9 100644
> --- a/drivers/media/platform/qcom/iris/iris_vpu_common.c
> +++ b/drivers/media/platform/qcom/iris/iris_vpu_common.c
> @@ -224,6 +224,7 @@ void iris_vpu_power_off_hw(struct iris_core *core)
>  {
>  	dev_pm_genpd_set_hwmode(core->pmdomain_tbl->pd_devs[IRIS_HW_POWER_DOMAIN], false);
>  	iris_disable_power_domains(core, core->pmdomain_tbl->pd_devs[IRIS_HW_POWER_DOMAIN]);
> +	iris_disable_unprepare_clock(core, IRIS_BSE_HW_CLK);

[Severity: High]
This isn't a bug introduced by this patch, but does this function disable
power domains before disabling the hardware clocks?

In iris_vpu_power_on_hw(), the sequence first enables the power domain,
then enables the clocks, and finally sets the hwmode. The error path of
iris_vpu_power_on_hw() correctly follows a last-in, first-out (LIFO) order
and disables the clocks before disabling the power domain.

However, iris_vpu_power_off_hw() calls iris_disable_power_domains() before
disabling the clocks. On ARM/Qualcomm platforms, turning off a power domain
(such as a GDSC) while its associated clocks are still running can prevent
the domain from fully collapsing, lead to bus hangs, or trigger
asynchronous external aborts (SErrors) when the clock controller
subsequently attempts to access unpowered registers.

By inserting the new IRIS_BSE_HW_CLK here, this patch perpetuates the
unsafe sequence. Should the teardown in iris_vpu_power_off_hw() be updated
to strictly mirror the reverse order used in the error path of
iris_vpu_power_on_hw()?

>  	iris_disable_unprepare_clock(core, IRIS_HW_AHB_CLK);
>  	iris_disable_unprepare_clock(core, IRIS_HW_CLK);
>  }

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20260529-enable_iris_on_purwa-v8-0-b1b9670459ab@oss.qualcomm.com?part=2

Re: [PATCH v8 0/5] media: iris: add support for purwa platform

[Jie Gan]

On 5/29/2026 3:34 PM, Wangao Wang wrote:
> This series enables the Iris video codec on purwa, allowing purwa to
> use hardware‑accelerated video encoding and decoding.
> 
> The Iris codec on purwa is nearly identical to the one on hamoa(X1E),
> except that it requires one additional clock and uses a different OPP
> table.
> 
> Therefore, purwa can reuse the Iris node from hamoa, but the clocks
> and OPP table need to be redefined.
> 
> All patches have been tested with v4l2-compliance and v4l2-ctl on
> purwa. And it does not affect existing targets.
> 

Please rebase on the latest linux-next tag, saw conflict with the commit:
95a337f92f0a  media: iris: switch to hardware mode after firmware boot

Thanks,
Jie

> Dependencies:
> https://lore.kernel.org/all/20260409-purwa-videocc-camcc-v4-0-5a8e5f2dd4b2@oss.qualcomm.com/
> 
> The result of v4l2-compliance on purwa:
> v4l2-compliance 1.31.0-5379, 64 bits, 64-bit time_t
> v4l2-compliance SHA: 14c988631ad4 2025-11-11 11:19:35
> 
> Compliance test for iris_driver device /dev/video0:
> 
> Driver Info:
>          Driver name      : iris_driver
>          Card type        : Iris Decoder
>          Bus info         : platform:aa00000.video-codec
>          Driver version   : 6.19.0
>          Capabilities     : 0x84204000
>                  Video Memory-to-Memory Multiplanar
>                  Streaming
>                  Extended Pix Format
>                  Device Capabilities
>          Device Caps      : 0x04204000
>                  Video Memory-to-Memory Multiplanar
>                  Streaming
>                  Extended Pix Format
>          Detected Stateful Decoder
> 
> Required ioctls:
>          test VIDIOC_QUERYCAP: OK
>          test invalid ioctls: OK
> 
> Allow for multiple opens:
>          test second /dev/video0 open: OK
>          test VIDIOC_QUERYCAP: OK
>          test VIDIOC_G/S_PRIORITY: OK
>          test for unlimited opens: OK
> 
> Debug ioctls:
>          test VIDIOC_DBG_G/S_REGISTER: OK (Not Supported)
>          test VIDIOC_LOG_STATUS: OK (Not Supported)
> 
> Input ioctls:
>          test VIDIOC_G/S_TUNER/ENUM_FREQ_BANDS: OK (Not Supported)
>          test VIDIOC_G/S_FREQUENCY: OK (Not Supported)
>          test VIDIOC_S_HW_FREQ_SEEK: OK (Not Supported)
>          test VIDIOC_ENUMAUDIO: OK (Not Supported)
>          test VIDIOC_G/S/ENUMINPUT: OK (Not Supported)
>          test VIDIOC_G/S_AUDIO: OK (Not Supported)
>          Inputs: 0 Audio Inputs: 0 Tuners: 0
> 
> Output ioctls:
>          test VIDIOC_G/S_MODULATOR: OK (Not Supported)
>          test VIDIOC_G/S_FREQUENCY: OK (Not Supported)
>          test VIDIOC_ENUMAUDOUT: OK (Not Supported)
>          test VIDIOC_G/S/ENUMOUTPUT: OK (Not Supported)
>          test VIDIOC_G/S_AUDOUT: OK (Not Supported)
>          Outputs: 0 Audio Outputs: 0 Modulators: 0
> 
> Input/Output configuration ioctls:
>          test VIDIOC_ENUM/G/S/QUERY_STD: OK (Not Supported)
>          test VIDIOC_ENUM/G/S/QUERY_DV_TIMINGS: OK (Not Supported)
>          test VIDIOC_DV_TIMINGS_CAP: OK (Not Supported)
>          test VIDIOC_G/S_EDID: OK (Not Supported)
> 
> Control ioctls:
>          test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: OK
>          test VIDIOC_QUERYCTRL: OK
>          test VIDIOC_G/S_CTRL: OK
>          test VIDIOC_G/S/TRY_EXT_CTRLS: OK
>          test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: OK
>          test VIDIOC_G/S_JPEGCOMP: OK (Not Supported)
>          Standard Controls: 10 Private Controls: 0
> 
> Format ioctls:
>          test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK
>          test VIDIOC_G/S_PARM: OK (Not Supported)
>          test VIDIOC_G_FBUF: OK (Not Supported)
>          test VIDIOC_G_FMT: OK
>          test VIDIOC_TRY_FMT: OK
>          test VIDIOC_S_FMT: OK
>          test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported)
>          test Cropping: OK
>          test Composing: OK
>          test Scaling: OK (Not Supported)
> 
> Codec ioctls:
>          test VIDIOC_(TRY_)ENCODER_CMD: OK (Not Supported)
>          test VIDIOC_G_ENC_INDEX: OK (Not Supported)
>          test VIDIOC_(TRY_)DECODER_CMD: OK
> 
> Buffer ioctls:
>          test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK
>          test CREATE_BUFS maximum buffers: OK
>          test VIDIOC_REMOVE_BUFS: OK
>          test VIDIOC_EXPBUF: OK
>          test Requests: OK (Not Supported)
>          test blocking wait: OK
> 
> Test input 0:
> 
> Streaming ioctls:
>          test read/write: OK (Not Supported)
> the input file is smaller than 7077888 bytes
>          Video Capture Multiplanar: Captured 65 buffers
>          test MMAP (select, REQBUFS): OK
> the input file is smaller than 7077888 bytes
>          Video Capture Multiplanar: Captured 65 buffers
>          test MMAP (epoll, REQBUFS): OK
> the input file is smaller than 7077888 bytes
>          Video Capture Multiplanar: Captured 65 buffers
>          test MMAP (select, CREATE_BUFS): OK
> the input file is smaller than 7077888 bytes
>          Video Capture Multiplanar: Captured 65 buffers
>          test MMAP (epoll, CREATE_BUFS): OK
>          test USERPTR (select): OK (Not Supported)
>          test DMABUF: Cannot test, specify --expbuf-device
> 
> Total for iris_driver device /dev/video0: 54, Succeeded: 54, Failed: 0, Warnings: 0
> root@localhost:/lib/video_test# ./v4l2-compliance -d /dev/video1 -s
> v4l2-compliance 1.31.0-5379, 64 bits, 64-bit time_t
> v4l2-compliance SHA: 14c988631ad4 2025-11-11 11:19:35
> 
> Compliance test for iris_driver device /dev/video1:
> 
> Driver Info:
>          Driver name      : iris_driver
>          Card type        : Iris Encoder
>          Bus info         : platform:aa00000.video-codec
>          Driver version   : 6.19.0
>          Capabilities     : 0x84204000
>                  Video Memory-to-Memory Multiplanar
>                  Streaming
>                  Extended Pix Format
>                  Device Capabilities
>          Device Caps      : 0x04204000
>                  Video Memory-to-Memory Multiplanar
>                  Streaming
>                  Extended Pix Format
>          Detected Stateful Encoder
> 
> Required ioctls:
>          test VIDIOC_QUERYCAP: OK
>          test invalid ioctls: OK
> 
> Allow for multiple opens:
>          test second /dev/video1 open: OK
>          test VIDIOC_QUERYCAP: OK
>          test VIDIOC_G/S_PRIORITY: OK
>          test for unlimited opens: OK
> 
> Debug ioctls:
>          test VIDIOC_DBG_G/S_REGISTER: OK (Not Supported)
>          test VIDIOC_LOG_STATUS: OK (Not Supported)
> 
> Input ioctls:
>          test VIDIOC_G/S_TUNER/ENUM_FREQ_BANDS: OK (Not Supported)
>          test VIDIOC_G/S_FREQUENCY: OK (Not Supported)
>          test VIDIOC_S_HW_FREQ_SEEK: OK (Not Supported)
>          test VIDIOC_ENUMAUDIO: OK (Not Supported)
>          test VIDIOC_G/S/ENUMINPUT: OK (Not Supported)
>          test VIDIOC_G/S_AUDIO: OK (Not Supported)
>          Inputs: 0 Audio Inputs: 0 Tuners: 0
> 
> Output ioctls:
>          test VIDIOC_G/S_MODULATOR: OK (Not Supported)
>          test VIDIOC_G/S_FREQUENCY: OK (Not Supported)
>          test VIDIOC_ENUMAUDOUT: OK (Not Supported)
>          test VIDIOC_G/S/ENUMOUTPUT: OK (Not Supported)
>          test VIDIOC_G/S_AUDOUT: OK (Not Supported)
>          Outputs: 0 Audio Outputs: 0 Modulators: 0
> 
> Input/Output configuration ioctls:
>          test VIDIOC_ENUM/G/S/QUERY_STD: OK (Not Supported)
>          test VIDIOC_ENUM/G/S/QUERY_DV_TIMINGS: OK (Not Supported)
>          test VIDIOC_DV_TIMINGS_CAP: OK (Not Supported)
>          test VIDIOC_G/S_EDID: OK (Not Supported)
> 
> Control ioctls:
>          test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: OK
>          test VIDIOC_QUERYCTRL: OK
>          test VIDIOC_G/S_CTRL: OK
>          test VIDIOC_G/S/TRY_EXT_CTRLS: OK
>          test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: OK
>          test VIDIOC_G/S_JPEGCOMP: OK (Not Supported)
>          Standard Controls: 38 Private Controls: 0
> 
> Format ioctls:
>          test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK
>          test VIDIOC_G/S_PARM: OK
>          test VIDIOC_G_FBUF: OK (Not Supported)
>          test VIDIOC_G_FMT: OK
>          test VIDIOC_TRY_FMT: OK
>          test VIDIOC_S_FMT: OK
>          test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported)
>          test Cropping: OK
>          test Composing: OK (Not Supported)
>          test Scaling: OK (Not Supported)
> 
> Codec ioctls:
>          test VIDIOC_(TRY_)ENCODER_CMD: OK
>          test VIDIOC_G_ENC_INDEX: OK (Not Supported)
>          test VIDIOC_(TRY_)DECODER_CMD: OK (Not Supported)
> 
> Buffer ioctls:
>          test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK
>          test CREATE_BUFS maximum buffers: OK
>          test VIDIOC_REMOVE_BUFS: OK
>          test VIDIOC_EXPBUF: OK
>          test Requests: OK (Not Supported)
>          test blocking wait: OK
> 
> Test input 0:
> 
> Streaming ioctls:
>          test read/write: OK (Not Supported)
>          Video Capture Multiplanar: Captured 61 buffers
>          test MMAP (select, REQBUFS): OK
>          Video Capture Multiplanar: Captured 61 buffers
>          test MMAP (epoll, REQBUFS): OK
>          Video Capture Multiplanar: Captured 61 buffers
>          test MMAP (select, CREATE_BUFS): OK
>          Video Capture Multiplanar: Captured 61 buffers
>          test MMAP (epoll, CREATE_BUFS): OK
>          test USERPTR (select): OK (Not Supported)
>          test DMABUF: Cannot test, specify --expbuf-device
> 
> Total for iris_driver device /dev/video1: 54, Succeeded: 54, Failed: 0, Warnings: 0
> 
> fluster result:
> H.264:
> Ran 77/135 tests successfully
> 
> H.265:
> Ran 131/147 tests successfully
> 
> VP9:
> Ran 235/305 tests successfully
> 
> Signed-off-by: Wangao Wang <wangao.wang@oss.qualcomm.com>
> ---
> Changes in v8:
> - Rebase onto the media-committers venus-iris-next branch.
> - Link to v7: https://lore.kernel.org/r/20260514-enable_iris_on_purwa-v7-0-47aa5b026f1a@oss.qualcomm.com
> 
> Changes in v7:
> - Rebase onto the media-committers next+fixes branch.
> - Correct the firmware name.
> - Link to v6: https://lore.kernel.org/r/20260507-enable_iris_on_purwa-v6-0-48da505e23bf@oss.qualcomm.com
> 
> Changes in v6:
> - Correct the firmware being used.(Dikshita)
> - Add comments to platform data.(Dikshita)
> - Link to v5: https://lore.kernel.org/r/20260429-enable_iris_on_purwa-v5-0-438fa96da248@oss.qualcomm.com
> 
> Changes in v5:
> - Modify the dt-binding description.(Krzysztof)
> - Move the BSE clock on/off handling into the vpu3 code.(Krzysztof)
> - Link to v4: https://lore.kernel.org/r/20260401-enable_iris_on_purwa-v4-0-ca784552a3e9@oss.qualcomm.com
> 
> Changes in v4:
> - Correct the dt-binding description.(Krzysztof)
> - Fix incorrect required-opps.(Dmitry)
> - Reuse the vpu3 power off hardware api.
> - Link to v3: https://lore.kernel.org/r/20260319-enable_iris_on_purwa-v3-0-bf8f3e9a8c9c@oss.qualcomm.com
> 
> Changes in v3:
> - Correct the dt-binding description.(Krzysztof)
> - Fix warnings reported in the patch.(Krzysztof)
> - Add separate power on/off hooks for Purwa.(Dmitry)
> - Link to v2: https://lore.kernel.org/r/20260306-enable_iris_on_purwa-v2-0-75fa80a0a9e3@oss.qualcomm.com
> 
> Changes in v2:
> - Improve the dt-binding description.(Krzysztof)
> - Move the BSE clock on/off handling into the vpu3 code.(Dmitry)
> - Add the required members to the platform data for Purwa.(Dikshita)
> - Link to v1: https://lore.kernel.org/r/20260209-enable_iris_on_purwa-v1-0-537c410f604f@oss.qualcomm.com
> 
> ---
> Wangao Wang (5):
>        dt-bindings: media: qcom,sm8550-iris: Add X1P42100 compatible
>        media: iris: Add hardware power on/off ops for X1P42100
>        media: iris: Add platform data for X1P42100
>        arm64: dts: qcom: purwa: Override Iris clocks and operating points
>        arm64: dts: qcom: purwa-iot-som: enable video
> 
>   .../bindings/media/qcom,sm8550-iris.yaml           | 23 +++++++++-
>   arch/arm64/boot/dts/qcom/purwa-iot-som.dtsi        |  4 ++
>   arch/arm64/boot/dts/qcom/purwa.dtsi                | 50 ++++++++++++++++++++++
>   .../platform/qcom/iris/iris_platform_common.h      |  1 +
>   .../media/platform/qcom/iris/iris_platform_vpu3x.c | 42 ++++++++++++++++++
>   .../platform/qcom/iris/iris_platform_x1p42100.h    | 22 ++++++++++
>   drivers/media/platform/qcom/iris/iris_probe.c      |  4 ++
>   drivers/media/platform/qcom/iris/iris_vpu_common.c |  9 +++-
>   8 files changed, 153 insertions(+), 2 deletions(-)
> ---
> base-commit: 735d2f48cadaa9a87e7c7601667878de70c771c5
> change-id: 20260209-enable_iris_on_purwa-a000527a098d
> prerequisite-change-id: 20260331-purwa-videocc-camcc-d9700d0f797d:v4
> prerequisite-patch-id: 61bdb45446193b72dd8a4b093e4ab2f78db2f066
> prerequisite-patch-id: b5be9dcbb612a14108f890b2782860847edfcbe4
> prerequisite-patch-id: 2f4d4c5c118e057c76e6d2785479df01d5bc1c7b
> prerequisite-patch-id: 026db5dd71d5b0472225ba72c8ba2781334143a9
> prerequisite-patch-id: 615e6f38e528de35dc206f1c7f3eaf78ff04afe2
> prerequisite-patch-id: 66096b909debe4d942eee972948d5a138a5be427
> prerequisite-patch-id: ee26e00cdde21ddb070af713230082ad3454422c
> 
> Best regards,

Re: [PATCH v8 4/5] arm64: dts: qcom: purwa: Override Iris clocks and operating points

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider:
- [Low] The device tree references an undefined macro `VIDEO_CC_MVS0_BSE_CLK`, which will cause a build failure.
--

commit b94ef34ae2cd7814137efba66c178dd0760ea44d
Author: Wangao Wang <wangao.wang@oss.qualcomm.com>

arm64: dts: qcom: purwa: Override Iris clocks and operating points

This commit modifies the device tree for the Purwa platform to override the
Iris clocks and operating points. It provides a new OPP table specific to the
X1P42100 platform to ensure correct performance levels.

> diff --git a/arch/arm64/boot/dts/qcom/purwa.dtsi b/arch/arm64/boot/dts/qcom/purwa.dtsi
> index 9ab4f26b35f29..b842ce5e7262e 100644
> --- a/arch/arm64/boot/dts/qcom/purwa.dtsi
> +++ b/arch/arm64/boot/dts/qcom/purwa.dtsi

[ ... ]

> @@ -157,6 +158,55 @@ &gpucc {
>  	compatible = "qcom,x1p42100-gpucc";
>  };
>  
> +&iris {
> +	compatible = "qcom,x1p42100-iris";
> +
> +	clocks = <&gcc GCC_VIDEO_AXI0_CLK>,
> +		 <&videocc VIDEO_CC_MVS0C_CLK>,
> +		 <&videocc VIDEO_CC_MVS0_CLK>,
> +		 <&videocc VIDEO_CC_MVS0_BSE_CLK>;

[Severity: Low]
Is VIDEO_CC_MVS0_BSE_CLK defined anywhere in the kernel? 

It appears this macro might be missing from the clock dt-bindings headers, 
which would cause the C preprocessor to leave it unexpanded as a string 
literal. Does this cause a dtc syntax error and break the device tree build?

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20260529-enable_iris_on_purwa-v8-0-b1b9670459ab@oss.qualcomm.com?part=4

Re: [PATCH v8 0/5] media: iris: add support for purwa platform

[Bryan O'Donoghue]

On 29/05/2026 09:46, Jie Gan wrote:
>> All patches have been tested with v4l2-compliance and v4l2-ctl on
>> purwa. And it does not affect existing targets.
>>
> Please rebase on the latest linux-next tag, saw conflict with the commit:
> 95a337f92f0a  media: iris: switch to hardware mode after firmware boot
> 
> Thanks,
> Jie

That's a -stable commit.

Base patches off of media-committers/next.

media-committers 
git@ssh.gitlab.freedesktop.org:linux-media/media-committers.git (fetch)
media-committers 
git@ssh.gitlab.freedesktop.org:linux-media/media-committers.git (push)

---
bod

Re: [PATCH v8 0/5] media: iris: add support for purwa platform

[Bryan O'Donoghue]

On 29/05/2026 08:34, Wangao Wang wrote:
> This series enables the Iris video codec on purwa, allowing purwa to
> use hardware‑accelerated video encoding and decoding.
> 
> The Iris codec on purwa is nearly identical to the one on hamoa(X1E),
> except that it requires one additional clock and uses a different OPP
> table.
> 
> Therefore, purwa can reuse the Iris node from hamoa, but the clocks
> and OPP table need to be redefined.
> 
> All patches have been tested with v4l2-compliance and v4l2-ctl on
> purwa. And it does not affect existing targets.
> 
> Dependencies:
> https://lore.kernel.org/all/20260409-purwa-videocc-camcc-v4-0-5a8e5f2dd4b2@oss.qualcomm.com/
> 
> The result of v4l2-compliance on purwa:
> v4l2-compliance 1.31.0-5379, 64 bits, 64-bit time_t
> v4l2-compliance SHA: 14c988631ad4 2025-11-11 11:19:35
> 
> Compliance test for iris_driver device /dev/video0:
> 
> Driver Info:
>          Driver name      : iris_driver
>          Card type        : Iris Decoder
>          Bus info         : platform:aa00000.video-codec
>          Driver version   : 6.19.0
>          Capabilities     : 0x84204000
>                  Video Memory-to-Memory Multiplanar
>                  Streaming
>                  Extended Pix Format
>                  Device Capabilities
>          Device Caps      : 0x04204000
>                  Video Memory-to-Memory Multiplanar
>                  Streaming
>                  Extended Pix Format
>          Detected Stateful Decoder
> 
> Required ioctls:
>          test VIDIOC_QUERYCAP: OK
>          test invalid ioctls: OK
> 
> Allow for multiple opens:
>          test second /dev/video0 open: OK
>          test VIDIOC_QUERYCAP: OK
>          test VIDIOC_G/S_PRIORITY: OK
>          test for unlimited opens: OK
> 
> Debug ioctls:
>          test VIDIOC_DBG_G/S_REGISTER: OK (Not Supported)
>          test VIDIOC_LOG_STATUS: OK (Not Supported)
> 
> Input ioctls:
>          test VIDIOC_G/S_TUNER/ENUM_FREQ_BANDS: OK (Not Supported)
>          test VIDIOC_G/S_FREQUENCY: OK (Not Supported)
>          test VIDIOC_S_HW_FREQ_SEEK: OK (Not Supported)
>          test VIDIOC_ENUMAUDIO: OK (Not Supported)
>          test VIDIOC_G/S/ENUMINPUT: OK (Not Supported)
>          test VIDIOC_G/S_AUDIO: OK (Not Supported)
>          Inputs: 0 Audio Inputs: 0 Tuners: 0
> 
> Output ioctls:
>          test VIDIOC_G/S_MODULATOR: OK (Not Supported)
>          test VIDIOC_G/S_FREQUENCY: OK (Not Supported)
>          test VIDIOC_ENUMAUDOUT: OK (Not Supported)
>          test VIDIOC_G/S/ENUMOUTPUT: OK (Not Supported)
>          test VIDIOC_G/S_AUDOUT: OK (Not Supported)
>          Outputs: 0 Audio Outputs: 0 Modulators: 0
> 
> Input/Output configuration ioctls:
>          test VIDIOC_ENUM/G/S/QUERY_STD: OK (Not Supported)
>          test VIDIOC_ENUM/G/S/QUERY_DV_TIMINGS: OK (Not Supported)
>          test VIDIOC_DV_TIMINGS_CAP: OK (Not Supported)
>          test VIDIOC_G/S_EDID: OK (Not Supported)
> 
> Control ioctls:
>          test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: OK
>          test VIDIOC_QUERYCTRL: OK
>          test VIDIOC_G/S_CTRL: OK
>          test VIDIOC_G/S/TRY_EXT_CTRLS: OK
>          test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: OK
>          test VIDIOC_G/S_JPEGCOMP: OK (Not Supported)
>          Standard Controls: 10 Private Controls: 0
> 
> Format ioctls:
>          test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK
>          test VIDIOC_G/S_PARM: OK (Not Supported)
>          test VIDIOC_G_FBUF: OK (Not Supported)
>          test VIDIOC_G_FMT: OK
>          test VIDIOC_TRY_FMT: OK
>          test VIDIOC_S_FMT: OK
>          test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported)
>          test Cropping: OK
>          test Composing: OK
>          test Scaling: OK (Not Supported)
> 
> Codec ioctls:
>          test VIDIOC_(TRY_)ENCODER_CMD: OK (Not Supported)
>          test VIDIOC_G_ENC_INDEX: OK (Not Supported)
>          test VIDIOC_(TRY_)DECODER_CMD: OK
> 
> Buffer ioctls:
>          test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK
>          test CREATE_BUFS maximum buffers: OK
>          test VIDIOC_REMOVE_BUFS: OK
>          test VIDIOC_EXPBUF: OK
>          test Requests: OK (Not Supported)
>          test blocking wait: OK
> 
> Test input 0:
> 
> Streaming ioctls:
>          test read/write: OK (Not Supported)
> the input file is smaller than 7077888 bytes
>          Video Capture Multiplanar: Captured 65 buffers
>          test MMAP (select, REQBUFS): OK
> the input file is smaller than 7077888 bytes
>          Video Capture Multiplanar: Captured 65 buffers
>          test MMAP (epoll, REQBUFS): OK
> the input file is smaller than 7077888 bytes
>          Video Capture Multiplanar: Captured 65 buffers
>          test MMAP (select, CREATE_BUFS): OK
> the input file is smaller than 7077888 bytes
>          Video Capture Multiplanar: Captured 65 buffers
>          test MMAP (epoll, CREATE_BUFS): OK
>          test USERPTR (select): OK (Not Supported)
>          test DMABUF: Cannot test, specify --expbuf-device
> 
> Total for iris_driver device /dev/video0: 54, Succeeded: 54, Failed: 0, Warnings: 0
> root@localhost:/lib/video_test# ./v4l2-compliance -d /dev/video1 -s
> v4l2-compliance 1.31.0-5379, 64 bits, 64-bit time_t
> v4l2-compliance SHA: 14c988631ad4 2025-11-11 11:19:35
> 
> Compliance test for iris_driver device /dev/video1:
> 
> Driver Info:
>          Driver name      : iris_driver
>          Card type        : Iris Encoder
>          Bus info         : platform:aa00000.video-codec
>          Driver version   : 6.19.0
>          Capabilities     : 0x84204000
>                  Video Memory-to-Memory Multiplanar
>                  Streaming
>                  Extended Pix Format
>                  Device Capabilities
>          Device Caps      : 0x04204000
>                  Video Memory-to-Memory Multiplanar
>                  Streaming
>                  Extended Pix Format
>          Detected Stateful Encoder
> 
> Required ioctls:
>          test VIDIOC_QUERYCAP: OK
>          test invalid ioctls: OK
> 
> Allow for multiple opens:
>          test second /dev/video1 open: OK
>          test VIDIOC_QUERYCAP: OK
>          test VIDIOC_G/S_PRIORITY: OK
>          test for unlimited opens: OK
> 
> Debug ioctls:
>          test VIDIOC_DBG_G/S_REGISTER: OK (Not Supported)
>          test VIDIOC_LOG_STATUS: OK (Not Supported)
> 
> Input ioctls:
>          test VIDIOC_G/S_TUNER/ENUM_FREQ_BANDS: OK (Not Supported)
>          test VIDIOC_G/S_FREQUENCY: OK (Not Supported)
>          test VIDIOC_S_HW_FREQ_SEEK: OK (Not Supported)
>          test VIDIOC_ENUMAUDIO: OK (Not Supported)
>          test VIDIOC_G/S/ENUMINPUT: OK (Not Supported)
>          test VIDIOC_G/S_AUDIO: OK (Not Supported)
>          Inputs: 0 Audio Inputs: 0 Tuners: 0
> 
> Output ioctls:
>          test VIDIOC_G/S_MODULATOR: OK (Not Supported)
>          test VIDIOC_G/S_FREQUENCY: OK (Not Supported)
>          test VIDIOC_ENUMAUDOUT: OK (Not Supported)
>          test VIDIOC_G/S/ENUMOUTPUT: OK (Not Supported)
>          test VIDIOC_G/S_AUDOUT: OK (Not Supported)
>          Outputs: 0 Audio Outputs: 0 Modulators: 0
> 
> Input/Output configuration ioctls:
>          test VIDIOC_ENUM/G/S/QUERY_STD: OK (Not Supported)
>          test VIDIOC_ENUM/G/S/QUERY_DV_TIMINGS: OK (Not Supported)
>          test VIDIOC_DV_TIMINGS_CAP: OK (Not Supported)
>          test VIDIOC_G/S_EDID: OK (Not Supported)
> 
> Control ioctls:
>          test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: OK
>          test VIDIOC_QUERYCTRL: OK
>          test VIDIOC_G/S_CTRL: OK
>          test VIDIOC_G/S/TRY_EXT_CTRLS: OK
>          test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: OK
>          test VIDIOC_G/S_JPEGCOMP: OK (Not Supported)
>          Standard Controls: 38 Private Controls: 0
> 
> Format ioctls:
>          test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK
>          test VIDIOC_G/S_PARM: OK
>          test VIDIOC_G_FBUF: OK (Not Supported)
>          test VIDIOC_G_FMT: OK
>          test VIDIOC_TRY_FMT: OK
>          test VIDIOC_S_FMT: OK
>          test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported)
>          test Cropping: OK
>          test Composing: OK (Not Supported)
>          test Scaling: OK (Not Supported)
> 
> Codec ioctls:
>          test VIDIOC_(TRY_)ENCODER_CMD: OK
>          test VIDIOC_G_ENC_INDEX: OK (Not Supported)
>          test VIDIOC_(TRY_)DECODER_CMD: OK (Not Supported)
> 
> Buffer ioctls:
>          test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK
>          test CREATE_BUFS maximum buffers: OK
>          test VIDIOC_REMOVE_BUFS: OK
>          test VIDIOC_EXPBUF: OK
>          test Requests: OK (Not Supported)
>          test blocking wait: OK
> 
> Test input 0:
> 
> Streaming ioctls:
>          test read/write: OK (Not Supported)
>          Video Capture Multiplanar: Captured 61 buffers
>          test MMAP (select, REQBUFS): OK
>          Video Capture Multiplanar: Captured 61 buffers
>          test MMAP (epoll, REQBUFS): OK
>          Video Capture Multiplanar: Captured 61 buffers
>          test MMAP (select, CREATE_BUFS): OK
>          Video Capture Multiplanar: Captured 61 buffers
>          test MMAP (epoll, CREATE_BUFS): OK
>          test USERPTR (select): OK (Not Supported)
>          test DMABUF: Cannot test, specify --expbuf-device
> 
> Total for iris_driver device /dev/video1: 54, Succeeded: 54, Failed: 0, Warnings: 0
> 
> fluster result:
> H.264:
> Ran 77/135 tests successfully
> 
> H.265:
> Ran 131/147 tests successfully
> 
> VP9:
> Ran 235/305 tests successfully
> 
> Signed-off-by: Wangao Wang <wangao.wang@oss.qualcomm.com>
> ---
> Changes in v8:
> - Rebase onto the media-committers venus-iris-next branch.
> - Link to v7: https://lore.kernel.org/r/20260514-enable_iris_on_purwa-v7-0-47aa5b026f1a@oss.qualcomm.com
> 
> Changes in v7:
> - Rebase onto the media-committers next+fixes branch.
> - Correct the firmware name.
> - Link to v6: https://lore.kernel.org/r/20260507-enable_iris_on_purwa-v6-0-48da505e23bf@oss.qualcomm.com
> 
> Changes in v6:
> - Correct the firmware being used.(Dikshita)
> - Add comments to platform data.(Dikshita)
> - Link to v5: https://lore.kernel.org/r/20260429-enable_iris_on_purwa-v5-0-438fa96da248@oss.qualcomm.com
> 
> Changes in v5:
> - Modify the dt-binding description.(Krzysztof)
> - Move the BSE clock on/off handling into the vpu3 code.(Krzysztof)
> - Link to v4: https://lore.kernel.org/r/20260401-enable_iris_on_purwa-v4-0-ca784552a3e9@oss.qualcomm.com
> 
> Changes in v4:
> - Correct the dt-binding description.(Krzysztof)
> - Fix incorrect required-opps.(Dmitry)
> - Reuse the vpu3 power off hardware api.
> - Link to v3: https://lore.kernel.org/r/20260319-enable_iris_on_purwa-v3-0-bf8f3e9a8c9c@oss.qualcomm.com
> 
> Changes in v3:
> - Correct the dt-binding description.(Krzysztof)
> - Fix warnings reported in the patch.(Krzysztof)
> - Add separate power on/off hooks for Purwa.(Dmitry)
> - Link to v2: https://lore.kernel.org/r/20260306-enable_iris_on_purwa-v2-0-75fa80a0a9e3@oss.qualcomm.com
> 
> Changes in v2:
> - Improve the dt-binding description.(Krzysztof)
> - Move the BSE clock on/off handling into the vpu3 code.(Dmitry)
> - Add the required members to the platform data for Purwa.(Dikshita)
> - Link to v1: https://lore.kernel.org/r/20260209-enable_iris_on_purwa-v1-0-537c410f604f@oss.qualcomm.com
> 
> ---
> Wangao Wang (5):
>        dt-bindings: media: qcom,sm8550-iris: Add X1P42100 compatible
>        media: iris: Add hardware power on/off ops for X1P42100
>        media: iris: Add platform data for X1P42100
>        arm64: dts: qcom: purwa: Override Iris clocks and operating points
>        arm64: dts: qcom: purwa-iot-som: enable video
> 
>   .../bindings/media/qcom,sm8550-iris.yaml           | 23 +++++++++-
>   arch/arm64/boot/dts/qcom/purwa-iot-som.dtsi        |  4 ++
>   arch/arm64/boot/dts/qcom/purwa.dtsi                | 50 ++++++++++++++++++++++
>   .../platform/qcom/iris/iris_platform_common.h      |  1 +
>   .../media/platform/qcom/iris/iris_platform_vpu3x.c | 42 ++++++++++++++++++
>   .../platform/qcom/iris/iris_platform_x1p42100.h    | 22 ++++++++++
>   drivers/media/platform/qcom/iris/iris_probe.c      |  4 ++
>   drivers/media/platform/qcom/iris/iris_vpu_common.c |  9 +++-
>   8 files changed, 153 insertions(+), 2 deletions(-)
> ---
> base-commit: 735d2f48cadaa9a87e7c7601667878de70c771c5
> change-id: 20260209-enable_iris_on_purwa-a000527a098d
> prerequisite-change-id: 20260331-purwa-videocc-camcc-d9700d0f797d:v4
> prerequisite-patch-id: 61bdb45446193b72dd8a4b093e4ab2f78db2f066
> prerequisite-patch-id: b5be9dcbb612a14108f890b2782860847edfcbe4
> prerequisite-patch-id: 2f4d4c5c118e057c76e6d2785479df01d5bc1c7b
> prerequisite-patch-id: 026db5dd71d5b0472225ba72c8ba2781334143a9
> prerequisite-patch-id: 615e6f38e528de35dc206f1c7f3eaf78ff04afe2
> prerequisite-patch-id: 66096b909debe4d942eee972948d5a138a5be427
> prerequisite-patch-id: ee26e00cdde21ddb070af713230082ad3454422c
> 
> Best regards,
> --
> Wangao Wang <wangao.wang@oss.qualcomm.com>
> 

Ehy why are camcc patches prerequisites for vidc ?

I'll drop all of that stuff since you don't depend on it and and you 
don't actually want to be gated by it.

---
bod

Re: [PATCH v8 0/5] media: iris: add support for purwa platform

[Wangao Wang]

On 2026/5/29 17:15, Bryan O'Donoghue wrote:
> 
> Ehy why are camcc patches prerequisites for vidc ?
> 
> I'll drop all of that stuff since you don't depend on it and and you 
> don't actually want to be gated by it.
> 
> ---
> bod

Only the last two patches of this series, which are the DT patches, 
depend on videocc. Please drop them. The driver is good to go.

-- 
Best Regards,
Wangao