[PATCH v4 00/19] firmware: qcom: scm: Add minidump SRAM destination support

[PATCH v4 00/19] firmware: qcom: scm: Add minidump SRAM destination support

[Mukesh Ojha]

On most Qualcomm SoCs where minidump is supported, a word in
always-on SRAM is shared between the operating system (OS) and
boot firmware.  Before DDR is initialised on the warm reset
following a crash, firmware reads this word to decide if minidump
is enabled and collect a minidump and where to deliver it:
destination (USB upload to a host, or save to local storage) and
OS is expected to select one destination.

This series wires that mechanism into the SCM driver:

[1]- The SRAM word location is described via a 'sram' phandle on the
  SCM DT node.

[2]- Add minidump-sram pattern property for older soc which supports
  minidump destination support.

[3-4]- Trivial change for consistency.

[5]- A 'minidump_dest' module parameter (default: usb) selects the
  destination.  Custom kernel_param_ops expose it as the human-
  readable strings "usb" or "storage".

[6-19]- Add the support for Kaanapali and other various SoCs.

Change in v4: https://lore.kernel.org/all/20260522195009.2961022-1-mukesh.ojha@oss.qualcomm.com/
 - Refactor commit text for 1, 2, 5.
 - added new commit(3/19) for existing  issue reported by Sasiko .

Changes in v3: https://lore.kernel.org/lkml/20260519171442.1582987-1-mukesh.ojha@oss.qualcomm.com/
 - Addressed some code improvement comments.
 - Removed example from scm binding.
 - Added minidump-sram binding which follows qcom,imem binding.
 - Added some more SoCs which supports this .

Changes in v2: https://lore.kernel.org/lkml/20260507080727.3227367-1-mukesh.ojha@oss.qualcomm.com/
 - Remove the restriction on the binding change done in v1.
 - Remove sram-name from binding.
 - sram definition is introduced and merged, so removed the refs from
   v1.
 - Minor change in the log as per comment s/find/get/
 - remove reference of sram-names
 - use minidump-sram instead of minidump-config.


Mukesh Ojha (19):
  dt-bindings: firmware: qcom,scm: Add minidump SRAM property
  dt-bindings: sram: qcom,imem: Add minidump-sram pattern property
  firmware: qcom: scm: Fix missing smp_load_acquire()
  firmware: qcom: scm: use dev_err_probe() for dload address failure
  firmware: qcom: scm: Add minidump SRAM support
  arm64: dts: qcom: kaanapali: Add minidump SRAM config to SCM node
  arm64: dts: qcom: sm8450: Add minidump SRAM config to SCM node
  arm64: dts: qcom: sa8775p: Add minidump SRAM config to SCM node
  arm64: dts: qcom: qcs8300: Add minidump SRAM config to SCM node
  arm64: dts: qcom: qdu1000: Add minidump SRAM config to SCM node
  arm64: dts: qcom: sm8550: Add minidump SRAM config to SCM node
  arm64: dts: qcom: sm8650: Add minidump SRAM config to SCM node
  arm64: dts: qcom: sc7280: Add minidump SRAM config to SCM node
  arm64: dts: qcom: sm8350: Add minidump SRAM config to SCM node
  arm64: dts: qcom: sc7180: Add minidump SRAM config to SCM node
  arm64: dts: qcom: sm6350: Add minidump SRAM config to SCM node
  arm64: dts: qcom: sm6375: Add minidump SRAM config to SCM node
  arm64: dts: qcom: qcs615: Add minidump SRAM config to SCM node
  arm64: dts: qcom: sdm845: Add minidump SRAM config to SCM node

 .../bindings/firmware/qcom,scm.yaml           |   7 +
 .../devicetree/bindings/sram/qcom,imem.yaml   |  16 +++
 arch/arm64/boot/dts/qcom/kaanapali.dtsi       |   5 +
 arch/arm64/boot/dts/qcom/kodiak.dtsi          |   5 +
 arch/arm64/boot/dts/qcom/lemans.dtsi          |   5 +
 arch/arm64/boot/dts/qcom/monaco.dtsi          |   5 +
 arch/arm64/boot/dts/qcom/qdu1000.dtsi         |   5 +
 arch/arm64/boot/dts/qcom/sc7180.dtsi          |   5 +
 arch/arm64/boot/dts/qcom/sdm845.dtsi          |   5 +
 arch/arm64/boot/dts/qcom/sm6350.dtsi          |   5 +
 arch/arm64/boot/dts/qcom/sm6375.dtsi          |   5 +
 arch/arm64/boot/dts/qcom/sm8350.dtsi          |   5 +
 arch/arm64/boot/dts/qcom/sm8450.dtsi          |   5 +
 arch/arm64/boot/dts/qcom/sm8550.dtsi          |   5 +
 arch/arm64/boot/dts/qcom/sm8650.dtsi          |   5 +
 arch/arm64/boot/dts/qcom/talos.dtsi           |   5 +
 drivers/firmware/qcom/qcom_scm.c              | 120 ++++++++++++++++--
 17 files changed, 201 insertions(+), 12 deletions(-)

-- 
2.53.0

[PATCH v4 01/19] dt-bindings: firmware: qcom,scm: Add minidump SRAM property

[Mukesh Ojha]

On Qualcomm SoCs that support minidump, a word in always-on SRAM
is shared between the Operating System(HLOS) and boot firmware.
OS is expected to select the minidump download destination
either USB upload to a host PC or save to on-device storage.
Boot firmware will reads this word before DDR is initialized
on the warm reset following a crash to decide where to deliver
the minidump.

Add a 'sram' property to the SCM binding to allow the OS to
identify this SRAM region via a phandle.

Signed-off-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
---
 Documentation/devicetree/bindings/firmware/qcom,scm.yaml | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/Documentation/devicetree/bindings/firmware/qcom,scm.yaml b/Documentation/devicetree/bindings/firmware/qcom,scm.yaml
index 25f62bacbc91..2d68b4065341 100644
--- a/Documentation/devicetree/bindings/firmware/qcom,scm.yaml
+++ b/Documentation/devicetree/bindings/firmware/qcom,scm.yaml
@@ -129,6 +129,13 @@ properties:
           - description: offset of the download mode control register
     description: TCSR hardware block
 
+  sram:
+    description:
+      Phandle to a region in always-on SRAM used to store the download
+      mode value for boot firmware to read before DDR is initialised on
+      the next warm reset.
+    maxItems: 1
+
 allOf:
   # Clocks
   - if:
-- 
2.53.0

Re: [PATCH v4 01/19] dt-bindings: firmware: qcom,scm: Add minidump SRAM property

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider:
- [Low] Missing property type reference (`$ref`) for the `sram` property in the dt-binding schema.
--

commit 6acd1cecaeb951d30398f9208dd4e87b7cfd156e
Author: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>

dt-bindings: firmware: qcom,scm: Add minidump SRAM property

This commit adds a new 'sram' property to the Qualcomm SCM dt-binding. The
property is intended to contain a phandle to a region in always-on SRAM used
for minidump download destination configuration. This allows the OS to share
information with the boot firmware across warm resets.

> diff --git a/Documentation/devicetree/bindings/firmware/qcom,scm.yaml b/Documentation/devicetree/bindings/firmware/qcom,scm.yaml
> index 7918d31f58b4a..82c661db0b616 100644
> --- a/Documentation/devicetree/bindings/firmware/qcom,scm.yaml
> +++ b/Documentation/devicetree/bindings/firmware/qcom,scm.yaml
> @@ -127,6 +127,13 @@ properties:
>            - description: offset of the download mode control register
>      description: TCSR hardware block
>  
> +  sram:
> +    description:
> +      Phandle to a region in always-on SRAM used to store the download
> +      mode value for boot firmware to read before DDR is initialised on
> +      the next warm reset.
> +    maxItems: 1

[Severity: Low]
Does this property need an explicit type reference, such as
$ref: /schemas/types.yaml#/definitions/phandle?

Without a type definition, the dt-schema validator might infer the property
as an untyped array based on the presence of maxItems: 1. Could this allow
malformed device trees to pass validation silently since it won't enforce
that the provided value is actually a valid phandle?

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20260624190830.3131112-1-mukesh.ojha@oss.qualcomm.com?part=1

[PATCH v4 02/19] dt-bindings: sram: qcom,imem: Add minidump-sram pattern property

[Mukesh Ojha]

The qcom,imem binding describes a single word in always-on SRAM shared
between the operating system (OS) and boot firmware. Before DDR is
initialized on the warm reset following a crash, firmware reads this
word to decide where to deliver the minidump, and the OS is expected to
select one of the destinations: either USB upload to a host PC or save
to on-device storage. If nothing is selected by the OS, USB is the
default.

Signed-off-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
---
 .../devicetree/bindings/sram/qcom,imem.yaml      | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/Documentation/devicetree/bindings/sram/qcom,imem.yaml b/Documentation/devicetree/bindings/sram/qcom,imem.yaml
index c63026904061..17adced6d3a4 100644
--- a/Documentation/devicetree/bindings/sram/qcom,imem.yaml
+++ b/Documentation/devicetree/bindings/sram/qcom,imem.yaml
@@ -67,6 +67,22 @@ properties:
     $ref: /schemas/power/reset/syscon-reboot-mode.yaml#
 
 patternProperties:
+  "^minidump-sram@[0-9a-f]+$":
+    type: object
+    description:
+      A word in always-on SRAM shared between the kernel and boot firmware.
+      Before DDR is initialised on the warm reset following a crash, firmware
+      reads this word to decide where to deliver the minidump (USB or storage).
+
+    properties:
+      reg:
+        maxItems: 1
+
+    required:
+      - reg
+
+    additionalProperties: false
+
   "^modem-tables@[0-9a-f]+$":
     type: object
     description:
-- 
2.53.0

[PATCH v4 03/19] firmware: qcom: scm: Fix missing smp_load_acquire()

[Mukesh Ojha]

__scm is published in qcom_scm_probe() with smp_store_release()
but qcom_scm_set_download_mode() reads it directly without
smp_load_acquire(), creating a potential ordering violation where a
CPU could observe a stale or partially initialised __scm pointer.

Use smp_load_acquire() to acquire __scm in the
qcom_scm_set_download_mode() function.

Signed-off-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
---
 drivers/firmware/qcom/qcom_scm.c | 25 ++++++++++++++-----------
 1 file changed, 14 insertions(+), 11 deletions(-)

diff --git a/drivers/firmware/qcom/qcom_scm.c b/drivers/firmware/qcom/qcom_scm.c
index 6b601a4b89db..b78da40a4d60 100644
--- a/drivers/firmware/qcom/qcom_scm.c
+++ b/drivers/firmware/qcom/qcom_scm.c
@@ -551,23 +551,23 @@ static int qcom_scm_io_rmw(phys_addr_t addr, unsigned int mask, unsigned int val
 	return qcom_scm_io_writel(addr, new);
 }
 
-static void qcom_scm_set_download_mode(u32 dload_mode)
+static void qcom_scm_set_download_mode(struct qcom_scm *scm, u32 dload_mode)
 {
 	int ret = 0;
 
-	if (__scm->dload_mode_addr) {
-		ret = qcom_scm_io_rmw(__scm->dload_mode_addr, QCOM_DLOAD_MASK,
+	if (scm->dload_mode_addr) {
+		ret = qcom_scm_io_rmw(scm->dload_mode_addr, QCOM_DLOAD_MASK,
 				      FIELD_PREP(QCOM_DLOAD_MASK, dload_mode));
-	} else if (__qcom_scm_is_call_available(__scm->dev, QCOM_SCM_SVC_BOOT,
+	} else if (__qcom_scm_is_call_available(scm->dev, QCOM_SCM_SVC_BOOT,
 						QCOM_SCM_BOOT_SET_DLOAD_MODE)) {
-		ret = __qcom_scm_set_dload_mode(__scm->dev, !!dload_mode);
+		ret = __qcom_scm_set_dload_mode(scm->dev, !!dload_mode);
 	} else if (dload_mode) {
-		dev_err(__scm->dev,
+		dev_err(scm->dev,
 			"No available mechanism for setting download mode\n");
 	}
 
 	if (ret)
-		dev_err(__scm->dev, "failed to set download mode: %d\n", ret);
+		dev_err(scm->dev, "failed to set download mode: %d\n", ret);
 }
 
 /**
@@ -2705,6 +2705,7 @@ static int get_download_mode(char *buffer, const struct kernel_param *kp)
 
 static int set_download_mode(const char *val, const struct kernel_param *kp)
 {
+	struct qcom_scm *scm;
 	bool tmp;
 	int ret;
 
@@ -2720,8 +2721,10 @@ static int set_download_mode(const char *val, const struct kernel_param *kp)
 	}
 
 	download_mode = ret;
-	if (__scm)
-		qcom_scm_set_download_mode(download_mode);
+	/* Pairs with smp_store_release() in qcom_scm_probe(). */
+	scm = smp_load_acquire(&__scm);
+	if (scm)
+		qcom_scm_set_download_mode(scm, download_mode);
 
 	return 0;
 }
@@ -2842,7 +2845,7 @@ static int qcom_scm_probe(struct platform_device *pdev)
 	 * will cause the boot stages to enter download mode, unless
 	 * disabled below by a clean shutdown/reboot.
 	 */
-	qcom_scm_set_download_mode(download_mode);
+	qcom_scm_set_download_mode(scm, download_mode);
 
 	/*
 	 * Disable SDI if indicated by DT that it is enabled by default.
@@ -2875,7 +2878,7 @@ static int qcom_scm_probe(struct platform_device *pdev)
 static void qcom_scm_shutdown(struct platform_device *pdev)
 {
 	/* Clean shutdown, disable download mode to allow normal restart */
-	qcom_scm_set_download_mode(QCOM_DLOAD_NODUMP);
+	qcom_scm_set_download_mode(__scm, QCOM_DLOAD_NODUMP);
 }
 
 static const struct of_device_id qcom_scm_dt_match[] = {
-- 
2.53.0

Re: [PATCH v4 03/19] firmware: qcom: scm: Fix missing smp_load_acquire()

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider:

Pre-existing issues:
- [High] The waitqueue interrupt is requested and enabled before the global __scm pointer is published, leading to a potential NULL pointer dereference in the IRQ handler path.
--

commit 181d68fe28239c2e3b0bbf1762f175bcdf577648
Author: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>

firmware: qcom: scm: Fix missing smp_load_acquire()

This commit fixes a potential ordering violation in
qcom_scm_set_download_mode() by using smp_load_acquire() to safely read
the __scm pointer published by qcom_scm_probe().

> diff --git a/drivers/firmware/qcom/qcom_scm.c b/drivers/firmware/qcom/qcom_scm.c
> index 9b06a69d3a6d7..c8a84836887f0 100644
> --- a/drivers/firmware/qcom/qcom_scm.c
> +++ b/drivers/firmware/qcom/qcom_scm.c
[ ... ]
> @@ -2841,7 +2844,7 @@ static int qcom_scm_probe(struct platform_device *pdev)
>  	 * will cause the boot stages to enter download mode, unless
>  	 * disabled below by a clean shutdown/reboot.
>  	 */
> -	qcom_scm_set_download_mode(download_mode);
> +	qcom_scm_set_download_mode(scm, download_mode);

[Severity: High]
This is a pre-existing issue, but since we are looking at the initialization
ordering in qcom_scm_probe() in drivers/firmware/qcom/qcom_scm.c, could the
IRQ registration order cause a NULL pointer dereference?

Earlier in qcom_scm_probe(), the waitqueue interrupt is enabled before the
global __scm pointer is published:

	ret = devm_request_threaded_irq(scm->dev, irq, NULL, qcom_scm_irq_handler,
					IRQF_ONESHOT, "qcom-scm", scm);
	...
	smp_store_release(&__scm, scm);

If a pending hardware interrupt fires before __scm is published, the IRQ
handler will execute. The handler calls qcom_scm_waitq_wakeup(), which invokes
qcom_scm_get_completion().

Could qcom_scm_get_completion() crash here, since it ignores the valid scm
context passed via the IRQ data and unconditionally dereferences __scm?

drivers/firmware/qcom/qcom_scm.c:qcom_scm_get_completion() {
	if (WARN_ON_ONCE(wq_ctx >= __scm->wq_cnt))
		return ERR_PTR(-EINVAL);
	...
}

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20260624190830.3131112-1-mukesh.ojha@oss.qualcomm.com?part=3

[PATCH v4 04/19] firmware: qcom: scm: use dev_err_probe() for dload address failure

[Mukesh Ojha]

Replace the bare `return ret` after qcom_scm_find_dload_address() with
dev_err_probe() to produce a consistent, deferred-probe-aware error
message when the download-mode address cannot be resolved.

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
---
 drivers/firmware/qcom/qcom_scm.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/firmware/qcom/qcom_scm.c b/drivers/firmware/qcom/qcom_scm.c
index b78da40a4d60..83e4810f1c53 100644
--- a/drivers/firmware/qcom/qcom_scm.c
+++ b/drivers/firmware/qcom/qcom_scm.c
@@ -2751,7 +2751,8 @@ static int qcom_scm_probe(struct platform_device *pdev)
 	scm->dev = &pdev->dev;
 	ret = qcom_scm_find_dload_address(&pdev->dev, &scm->dload_mode_addr);
 	if (ret < 0)
-		return ret;
+		return dev_err_probe(&pdev->dev, ret,
+				     "Failed to get download mode address\n");
 
 	mutex_init(&scm->scm_bw_lock);
 
-- 
2.53.0

Re: [PATCH v4 04/19] firmware: qcom: scm: use dev_err_probe() for dload address failure

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 2 potential issue(s) to consider:

Pre-existing issues:
- [High] The global `qcom_tzmem_dev` pointer is set during `qcom_tzmem_enable()` but is never cleared on probe failure, causing subsequent probe retries to permanently fail with `-EBUSY`.
- [High] The probe function calls `of_reserved_mem_device_init()` but does not call `of_reserved_mem_device_release()` on subsequent error paths, leading to permanent probe failure or resource leaks upon probe retry.
--

commit 6dc15526252b78a9c217f06ed35ed4966a794450
Author: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>

firmware: qcom: scm: use dev_err_probe() for dload address failure

Replace the bare return ret after qcom_scm_find_dload_address() with
dev_err_probe() to produce a consistent, deferred-probe-aware error
message when the download-mode address cannot be resolved.

> diff --git a/drivers/firmware/qcom/qcom_scm.c b/drivers/firmware/qcom/qcom_scm.c
> index c8a84836887f0..6cd4d9468456f 100644
> --- a/drivers/firmware/qcom/qcom_scm.c
> +++ b/drivers/firmware/qcom/qcom_scm.c
> @@ -2750,7 +2750,8 @@ static int qcom_scm_probe(struct platform_device *pdev)
>  	scm->dev = &pdev->dev;
>  	ret = qcom_scm_find_dload_address(&pdev->dev, &scm->dload_mode_addr);
>  	if (ret < 0)
> -		return ret;
> +		return dev_err_probe(&pdev->dev, ret,
> +				     "Failed to get download mode address\n");
>  
>  	mutex_init(&scm->scm_bw_lock);

[Severity: High]
This is a pre-existing issue, but does qcom_scm_probe() properly release
resources on later probe failures?

Later in qcom_scm_probe(), of_reserved_mem_device_init() is called to setup
reserved memory:

drivers/firmware/qcom/qcom_scm.c:qcom_scm_probe() {
	...
	ret = of_reserved_mem_device_init(scm->dev);
	if (ret && ret != -ENODEV)
		return dev_err_probe(scm->dev, ret,
				     "Failed to setup the reserved memory region for TZ mem\n");
	...
}

However, subsequent error paths, such as platform_get_irq_optional() returning
-EPROBE_DEFER, exit directly without calling of_reserved_mem_device_release().

If the probe is deferred, will this cause the next probe attempt to fail with
-EBUSY, or leak memory by duplicating the rmem_assigned_device list entry on
every retry?

[Severity: High]
This is a pre-existing issue, but does qcom_tzmem_enable() cause a permanent
probe failure if qcom_scm_probe() defers later in the function?

qcom_tzmem_enable() sets a static qcom_tzmem_dev pointer in qcom_tzmem.c:

drivers/firmware/qcom/qcom_tzmem.c:qcom_tzmem_enable() {
	if (qcom_tzmem_dev)
		return -EBUSY;

	qcom_tzmem_dev = dev;

	return qcom_tzmem_init();
}

Since qcom_scm_probe() does not clear this pointer if it defers after this
call, will subsequent probe retries permanently fail with -EBUSY when
qcom_tzmem_enable() checks the still-set pointer?

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20260624190830.3131112-1-mukesh.ojha@oss.qualcomm.com?part=4

[PATCH v4 05/19] firmware: qcom: scm: Add minidump SRAM support

[Mukesh Ojha]

On most Qualcomm SoCs where minidump is supported, a word in always-on
SRAM is shared between the operating system (OS) and boot firmware.
Before DDR is initialized on the warm reset following a crash, firmware
reads this word to decide if minidump is enabled and collect a minidump,
and where to deliver it (USB upload to a host, or save to local
storage). The OS is expected to select one of the destinations.

The SRAM region is described by a 'sram' phandle on the SCM DT node.
If the property is absent the feature is silently disabled, keeping
existing SoCs unaffected.

Expose a 'minidump_dest' module parameter (default: usb) so the user
can select the destination. Only the string names "usb" or "storage"
are accepted.

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
---
 drivers/firmware/qcom/qcom_scm.c | 92 ++++++++++++++++++++++++++++++++
 1 file changed, 92 insertions(+)

diff --git a/drivers/firmware/qcom/qcom_scm.c b/drivers/firmware/qcom/qcom_scm.c
index 83e4810f1c53..ba5cdeed8a04 100644
--- a/drivers/firmware/qcom/qcom_scm.c
+++ b/drivers/firmware/qcom/qcom_scm.c
@@ -57,6 +57,7 @@ struct qcom_scm {
 	int scm_vote_count;
 
 	u64 dload_mode_addr;
+	void __iomem *minidump_sram;
 
 	struct qcom_tzmem_pool *mempool;
 	unsigned int wq_cnt;
@@ -141,6 +142,20 @@ static const u8 qcom_scm_cpu_warm_bits[QCOM_SCM_BOOT_MAX_CPUS] = {
 #define QCOM_DLOAD_MINIDUMP	2
 #define QCOM_DLOAD_BOTHDUMP	3
 
+/* Minidump destination values written to always-on SRAM for boot firmware */
+#define QCOM_MINIDUMP_DEST_USB		0x0
+#define QCOM_MINIDUMP_DEST_STORAGE	0x2
+
+static u32 minidump_dest = QCOM_MINIDUMP_DEST_USB;
+
+static const struct {
+	const char *name;
+	u32 val;
+} minidump_dest_map[] = {
+	{ "usb",     QCOM_MINIDUMP_DEST_USB     },
+	{ "storage", QCOM_MINIDUMP_DEST_STORAGE },
+};
+
 #define QCOM_SCM_DEFAULT_WAITQ_COUNT 1
 
 static const char * const qcom_scm_convention_names[] = {
@@ -568,6 +583,14 @@ static void qcom_scm_set_download_mode(struct qcom_scm *scm, u32 dload_mode)
 
 	if (ret)
 		dev_err(scm->dev, "failed to set download mode: %d\n", ret);
+
+	/*
+	 * Write the destination into the always-on SRAM so boot firmware
+	 * can read it before DDR is initialised on the next warm reset.
+	 * Only written when minidump is active;
+	 */
+	if (scm->minidump_sram && (dload_mode & QCOM_DLOAD_MINIDUMP))
+		writel_relaxed(minidump_dest, scm->minidump_sram);
 }
 
 /**
@@ -2040,6 +2063,29 @@ int qcom_scm_gpu_init_regs(u32 gpu_req)
 }
 EXPORT_SYMBOL_GPL(qcom_scm_gpu_init_regs);
 
+static int qcom_scm_map_minidump_sram(struct device *dev, void __iomem **out)
+{
+	struct device_node *np = dev->of_node;
+	struct device_node *sram_np;
+	struct resource res;
+	int ret;
+
+	sram_np = of_parse_phandle(np, "sram", 0);
+	if (!sram_np)
+		return 0;
+
+	ret = of_address_to_resource(sram_np, 0, &res);
+	of_node_put(sram_np);
+	if (ret)
+		return ret;
+
+	*out = devm_ioremap(dev, res.start, resource_size(&res));
+	if (!*out)
+		return -ENOMEM;
+
+	return 0;
+}
+
 static int qcom_scm_find_dload_address(struct device *dev, u64 *addr)
 {
 	struct device_node *tcsr;
@@ -2737,6 +2783,47 @@ static const struct kernel_param_ops download_mode_param_ops = {
 module_param_cb(download_mode, &download_mode_param_ops, NULL, 0644);
 MODULE_PARM_DESC(download_mode, "download mode: off/0/N for no dump mode, full/on/1/Y for full dump mode, mini for minidump mode and full,mini for both full and minidump mode together are acceptable values");
 
+static int get_minidump_dest(char *buffer, const struct kernel_param *kp)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(minidump_dest_map); i++)
+		if (minidump_dest == minidump_dest_map[i].val)
+			return sysfs_emit(buffer, "%s\n", minidump_dest_map[i].name);
+
+	return sysfs_emit(buffer, "unknown\n");
+}
+
+static int set_minidump_dest(const char *val, const struct kernel_param *kp)
+{
+	struct qcom_scm *scm;
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(minidump_dest_map); i++)
+		if (sysfs_streq(val, minidump_dest_map[i].name))
+			break;
+
+	if (i >= ARRAY_SIZE(minidump_dest_map))
+		return -EINVAL;
+
+	minidump_dest = minidump_dest_map[i].val;
+
+	/* Pairs with smp_store_release() in qcom_scm_probe(). */
+	scm = smp_load_acquire(&__scm);
+	if (scm && scm->minidump_sram && (download_mode & QCOM_DLOAD_MINIDUMP))
+		writel_relaxed(minidump_dest, scm->minidump_sram);
+
+	return 0;
+}
+
+static const struct kernel_param_ops minidump_dest_param_ops = {
+	.get = get_minidump_dest,
+	.set = set_minidump_dest,
+};
+
+module_param_cb(minidump_dest, &minidump_dest_param_ops, NULL, 0644);
+MODULE_PARM_DESC(minidump_dest, "Minidump SRAM destination: usb (default) or storage");
+
 static int qcom_scm_probe(struct platform_device *pdev)
 {
 	struct qcom_tzmem_pool_config pool_config;
@@ -2754,6 +2841,11 @@ static int qcom_scm_probe(struct platform_device *pdev)
 		return dev_err_probe(&pdev->dev, ret,
 				     "Failed to get download mode address\n");
 
+	ret = qcom_scm_map_minidump_sram(&pdev->dev, &scm->minidump_sram);
+	if (ret < 0)
+		return dev_err_probe(&pdev->dev, ret,
+				     "Failed to map minidump SRAM\n");
+
 	mutex_init(&scm->scm_bw_lock);
 
 	scm->path = devm_of_icc_get(&pdev->dev, NULL);
-- 
2.53.0

[PATCH v4 06/19] arm64: dts: qcom: kaanapali: Add minidump SRAM config to SCM node

[Mukesh Ojha]

Point the SCM node at the minidump config slot in the always-on SRAM.
Boot firmware reads this word before DDR is initialised on a warm reset
to decide where to deliver the minidump.

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/kaanapali.dtsi | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/kaanapali.dtsi b/arch/arm64/boot/dts/qcom/kaanapali.dtsi
index 7aa9653bd456..0342fd28f9b9 100644
--- a/arch/arm64/boot/dts/qcom/kaanapali.dtsi
+++ b/arch/arm64/boot/dts/qcom/kaanapali.dtsi
@@ -224,6 +224,7 @@ scm: scm {
 			qcom,dload-mode = <&tcsr 0x19000>;
 			interconnects = <&aggre_noc MASTER_CRYPTO QCOM_ICC_TAG_ALWAYS
 					 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
+			sram = <&minidump_config>;
 		};
 
 		scmi: scmi {
@@ -5452,6 +5453,10 @@ sram@14680000 {
 			#address-cells = <1>;
 			#size-cells = <1>;
 
+			minidump_config: minidump-sram@1c {
+				reg = <0x1c 0x4>;
+			};
+
 			pil-sram@94c {
 				compatible = "qcom,pil-reloc-info";
 				reg = <0x94c 0xc8>;
-- 
2.53.0

[PATCH v4 07/19] arm64: dts: qcom: sm8450: Add minidump SRAM config to SCM node

[Mukesh Ojha]

Point the SCM node at the minidump config slot in the always-on SRAM.
Boot firmware reads this word before DDR is initialised on a warm reset
to decide where to deliver the minidump.

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index 56cb6e959e4e..f819b4f7fdbc 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -479,6 +479,7 @@ scm: scm {
 			compatible = "qcom,scm-sm8450", "qcom,scm";
 			qcom,dload-mode = <&tcsr 0x13000>;
 			interconnects = <&aggre2_noc MASTER_CRYPTO 0 &mc_virt SLAVE_EBI1 0>;
+			sram = <&minidump_config>;
 			#reset-cells = <1>;
 		};
 	};
@@ -4978,6 +4979,10 @@ sram@146aa000 {
 			#address-cells = <1>;
 			#size-cells = <1>;
 
+			minidump_config: minidump-sram@1c {
+				reg = <0x1c 0x4>;
+			};
+
 			pil-reloc@94c {
 				compatible = "qcom,pil-reloc-info";
 				reg = <0x94c 0xc8>;
-- 
2.53.0

[PATCH v4 08/19] arm64: dts: qcom: sa8775p: Add minidump SRAM config to SCM node

[Mukesh Ojha]

Point the SCM node at the minidump config slot in the always-on SRAM.
Boot firmware reads this word before DDR is initialised on a warm reset
to decide where to deliver the minidump.

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/lemans.dtsi | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/lemans.dtsi b/arch/arm64/boot/dts/qcom/lemans.dtsi
index 353a6e6fd3ac..a1708bd15076 100644
--- a/arch/arm64/boot/dts/qcom/lemans.dtsi
+++ b/arch/arm64/boot/dts/qcom/lemans.dtsi
@@ -524,6 +524,7 @@ firmware {
 		scm {
 			compatible = "qcom,scm-sa8775p", "qcom,scm";
 			qcom,dload-mode = <&tcsr 0x13000>;
+			sram = <&minidump_config>;
 		};
 	};
 
@@ -6825,6 +6826,10 @@ sram: sram@146d8000 {
 			#address-cells = <1>;
 			#size-cells = <1>;
 
+			minidump_config: minidump-sram@1c {
+				reg = <0x1c 0x4>;
+			};
+
 			pil-reloc@94c {
 				compatible = "qcom,pil-reloc-info";
 				reg = <0x94c 0xc8>;
-- 
2.53.0

[PATCH v4 09/19] arm64: dts: qcom: qcs8300: Add minidump SRAM config to SCM node

[Mukesh Ojha]

Point the SCM node at the minidump config slot in the always-on SRAM.
Boot firmware reads this word before DDR is initialised on a warm reset
to decide where to deliver the minidump.

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/monaco.dtsi | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/monaco.dtsi b/arch/arm64/boot/dts/qcom/monaco.dtsi
index e4c8466f941b..a05b8d28bdb8 100644
--- a/arch/arm64/boot/dts/qcom/monaco.dtsi
+++ b/arch/arm64/boot/dts/qcom/monaco.dtsi
@@ -634,6 +634,7 @@ firmware {
 		scm: scm {
 			compatible = "qcom,scm-qcs8300", "qcom,scm";
 			qcom,dload-mode = <&tcsr 0x13000>;
+			sram = <&minidump_config>;
 		};
 	};
 
@@ -7154,6 +7155,10 @@ sram: sram@146d8000 {
 			#address-cells = <1>;
 			#size-cells = <1>;
 
+			minidump_config: minidump-sram@1c {
+				reg = <0x1c 0x4>;
+			};
+
 			pil-reloc@94c {
 				compatible = "qcom,pil-reloc-info";
 				reg = <0x94c 0xc8>;
-- 
2.53.0

[PATCH v4 10/19] arm64: dts: qcom: qdu1000: Add minidump SRAM config to SCM node

[Mukesh Ojha]

Point the SCM node at the minidump config slot in the always-on SRAM.
Boot firmware reads this word before DDR is initialised on a warm reset
to decide where to deliver the minidump.

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/qdu1000.dtsi | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/qdu1000.dtsi b/arch/arm64/boot/dts/qcom/qdu1000.dtsi
index 952d4270d118..0c6ae3ff06fb 100644
--- a/arch/arm64/boot/dts/qcom/qdu1000.dtsi
+++ b/arch/arm64/boot/dts/qcom/qdu1000.dtsi
@@ -171,6 +171,7 @@ cluster_sleep_1: cluster-sleep-1 {
 	firmware {
 		scm {
 			compatible = "qcom,scm-qdu1000", "qcom,scm";
+			sram = <&minidump_config>;
 		};
 	};
 
@@ -1369,6 +1370,10 @@ sram@14680000 {
 			#address-cells = <1>;
 			#size-cells = <1>;
 
+			minidump_config: minidump-sram@1c {
+				reg = <0x1c 0x4>;
+			};
+
 			pil-reloc@94c {
 				compatible = "qcom,pil-reloc-info";
 				reg = <0x94c 0xc8>;
-- 
2.53.0

[PATCH v4 11/19] arm64: dts: qcom: sm8550: Add minidump SRAM config to SCM node

[Mukesh Ojha]

Point the SCM node at the minidump config slot in the always-on SRAM.
Boot firmware reads this word before DDR is initialised on a warm reset
to decide where to deliver the minidump.

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/sm8550.dtsi | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8550.dtsi b/arch/arm64/boot/dts/qcom/sm8550.dtsi
index 396201905ef2..8830da63261f 100644
--- a/arch/arm64/boot/dts/qcom/sm8550.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8550.dtsi
@@ -391,6 +391,7 @@ scm: scm {
 			qcom,dload-mode = <&tcsr 0x19000>;
 			interconnects = <&aggre2_noc MASTER_CRYPTO QCOM_ICC_TAG_ALWAYS
 					 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
+			sram = <&minidump_config>;
 		};
 	};
 
@@ -5537,6 +5538,10 @@ sram@14680000 {
 
 			ranges = <0 0 0x14680000 0x2c000>;
 
+			minidump_config: minidump-sram@1c {
+				reg = <0x1c 0x4>;
+			};
+
 			ipa_modem_tables: modem-tables@8000 {
 				reg = <0x8000 0x2000>;
 			};
-- 
2.53.0

[PATCH v4 12/19] arm64: dts: qcom: sm8650: Add minidump SRAM config to SCM node

[Mukesh Ojha]

Point the SCM node at the minidump config slot in the always-on SRAM.
Boot firmware reads this word before DDR is initialised on a warm reset
to decide where to deliver the minidump.

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/sm8650.dtsi | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8650.dtsi b/arch/arm64/boot/dts/qcom/sm8650.dtsi
index 160ead25ecf7..88751d3b72cd 100644
--- a/arch/arm64/boot/dts/qcom/sm8650.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8650.dtsi
@@ -645,6 +645,7 @@ scm: scm {
 			qcom,dload-mode = <&tcsr 0x19000>;
 			interconnects = <&aggre2_noc MASTER_CRYPTO QCOM_ICC_TAG_ALWAYS
 					 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
+			sram = <&minidump_config>;
 		};
 	};
 
@@ -7091,6 +7092,10 @@ sram@14680000 {
 
 			ranges = <0 0 0x14680000 0x2c000>;
 
+			minidump_config: minidump-sram@1c {
+				reg = <0x1c 0x4>;
+			};
+
 			ipa_modem_tables: modem-tables@8000 {
 				reg = <0x8000 0x2000>;
 			};
-- 
2.53.0

[PATCH v4 13/19] arm64: dts: qcom: sc7280: Add minidump SRAM config to SCM node

[Mukesh Ojha]

Point the SCM node at the minidump config slot in the always-on SRAM.
Boot firmware reads this word before DDR is initialised on a warm reset
to decide where to deliver the minidump.

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/kodiak.dtsi | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/kodiak.dtsi b/arch/arm64/boot/dts/qcom/kodiak.dtsi
index fa540d8c2615..6d805cbe5b4f 100644
--- a/arch/arm64/boot/dts/qcom/kodiak.dtsi
+++ b/arch/arm64/boot/dts/qcom/kodiak.dtsi
@@ -720,6 +720,7 @@ firmware {
 		scm: scm {
 			compatible = "qcom,scm-sc7280", "qcom,scm";
 			qcom,dload-mode = <&tcsr_2 0x13000>;
+			sram = <&minidump_config>;
 		};
 	};
 
@@ -6698,6 +6699,10 @@ sram@146a5000 {
 
 			ranges = <0 0 0x146a5000 0x6000>;
 
+			minidump_config: minidump-sram@1c {
+				reg = <0x1c 0x4>;
+			};
+
 			ipa_modem_tables: modem-tables@3000 {
 				reg = <0x3000 0x2000>;
 			};
-- 
2.53.0

[PATCH v4 14/19] arm64: dts: qcom: sm8350: Add minidump SRAM config to SCM node

[Mukesh Ojha]

Point the SCM node at the minidump config slot in the always-on SRAM.
Boot firmware reads this word before DDR is initialised on a warm reset
to decide where to deliver the minidump.

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/sm8350.dtsi | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi
index c830953156ec..dea97330da49 100644
--- a/arch/arm64/boot/dts/qcom/sm8350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi
@@ -293,6 +293,7 @@ firmware {
 		scm: scm {
 			compatible = "qcom,scm-sm8350", "qcom,scm";
 			qcom,dload-mode = <&tcsr 0x13000>;
+			sram = <&minidump_config>;
 			#reset-cells = <1>;
 		};
 	};
@@ -3451,6 +3452,10 @@ sram@14680000 {
 
 			ranges = <0 0 0x14680000 0x40000>;
 
+			minidump_config: minidump-sram@1c {
+				reg = <0x1c 0x4>;
+			};
+
 			ipa_modem_tables: modem-tables@3d000 {
 				reg = <0x3d000 0x2000>;
 			};
-- 
2.53.0

[PATCH v4 15/19] arm64: dts: qcom: sc7180: Add minidump SRAM config to SCM node

[Mukesh Ojha]

Point the SCM node at the minidump config slot in the always-on SRAM.
Boot firmware reads this word before DDR is initialised on a warm reset
to decide where to deliver the minidump.

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/sc7180.dtsi | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
index fa65c485172f..1f51fd431ce5 100644
--- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
@@ -385,6 +385,7 @@ cluster_aoss_sleep: cluster-sleep-2 {
 	firmware {
 		scm: scm {
 			compatible = "qcom,scm-sc7180", "qcom,scm";
+			sram = <&minidump_config>;
 		};
 	};
 
@@ -3596,6 +3597,10 @@ sram@14680000 {
 
 			ranges = <0 0 0x14680000 0x2e000>;
 
+			minidump_config: minidump-sram@1c {
+				reg = <0x1c 0x4>;
+			};
+
 			ipa_modem_tables: modem-tables@28000 {
 				reg = <0x28000 0x2000>;
 			};
-- 
2.53.0

[PATCH v4 16/19] arm64: dts: qcom: sm6350: Add minidump SRAM config to SCM node

[Mukesh Ojha]

Point the SCM node at the minidump config slot in the always-on SRAM.
Boot firmware reads this word before DDR is initialised on a warm reset
to decide where to deliver the minidump.

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/sm6350.dtsi | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
index d6adf68563cb..06892ba22875 100644
--- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
@@ -363,6 +363,7 @@ big_cpu_sleep_1: cpu-sleep-1-1 {
 	firmware {
 		scm: scm {
 			compatible = "qcom,scm-sm6350", "qcom,scm";
+			sram = <&minidump_config>;
 			#reset-cells = <1>;
 		};
 	};
@@ -2808,6 +2809,10 @@ sram@14680000 {
 
 			ranges = <0 0 0x14680000 0x2e000>;
 
+			minidump_config: minidump-sram@1c {
+				reg = <0x1c 0x4>;
+			};
+
 			ipa_modem_tables: modem-tables@28000 {
 				reg = <0x28000 0x2000>;
 			};
-- 
2.53.0

[PATCH v4 17/19] arm64: dts: qcom: sm6375: Add minidump SRAM config to SCM node

[Mukesh Ojha]

Point the SCM node at the minidump config slot in the always-on SRAM.
Boot firmware reads this word before DDR is initialised on a warm reset
to decide where to deliver the minidump.

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/sm6375.dtsi | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6375.dtsi b/arch/arm64/boot/dts/qcom/sm6375.dtsi
index ccf572bb1549..71a228597093 100644
--- a/arch/arm64/boot/dts/qcom/sm6375.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6375.dtsi
@@ -307,6 +307,7 @@ scm {
 			compatible = "qcom,scm-sm6375", "qcom,scm";
 			clocks = <&rpmcc RPM_SMD_CE1_CLK>;
 			clock-names = "core";
+			sram = <&minidump_config>;
 			#reset-cells = <1>;
 		};
 	};
@@ -1645,6 +1646,10 @@ sram@c125000 {
 			#address-cells = <1>;
 			#size-cells = <1>;
 
+			minidump_config: minidump-sram@1c {
+				reg = <0x1c 0x4>;
+			};
+
 			pil-reloc@94c {
 				compatible = "qcom,pil-reloc-info";
 				reg = <0x94c 0xc8>;
-- 
2.53.0

[PATCH v4 18/19] arm64: dts: qcom: qcs615: Add minidump SRAM config to SCM node

[Mukesh Ojha]

Point the SCM node at the minidump config slot in the always-on SRAM.
Boot firmware reads this word before DDR is initialised on a warm reset
to decide where to deliver the minidump.

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/talos.dtsi | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/talos.dtsi b/arch/arm64/boot/dts/qcom/talos.dtsi
index fb1bbc51bb8a..a358d5441fa9 100644
--- a/arch/arm64/boot/dts/qcom/talos.dtsi
+++ b/arch/arm64/boot/dts/qcom/talos.dtsi
@@ -473,6 +473,7 @@ firmware {
 		scm {
 			compatible = "qcom,scm-qcs615", "qcom,scm";
 			qcom,dload-mode = <&tcsr 0x13000>;
+			sram = <&minidump_config>;
 		};
 	};
 
@@ -4654,6 +4655,10 @@ sram@14680000 {
 			#address-cells = <1>;
 			#size-cells = <1>;
 
+			minidump_config: minidump-sram@1c {
+				reg = <0x1c 0x4>;
+			};
+
 			pil-reloc@2a94c {
 				compatible = "qcom,pil-reloc-info";
 				reg = <0x2a94c 0xc8>;
-- 
2.53.0

[PATCH v4 19/19] arm64: dts: qcom: sdm845: Add minidump SRAM config to SCM node

[Mukesh Ojha]

Point the SCM node at the minidump config slot in the always-on SRAM.
Boot firmware reads this word before DDR is initialised on a warm reset
to decide where to deliver the minidump.

Signed-off-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/sdm845.dtsi | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
index 4ae8627d6dbc..2179988dbaaf 100644
--- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
@@ -363,6 +363,7 @@ cluster_sleep_0: cluster-sleep-0 {
 	firmware {
 		scm {
 			compatible = "qcom,scm-sdm845", "qcom,scm";
+			sram = <&minidump_config>;
 		};
 	};
 
@@ -5192,6 +5193,10 @@ sram@14680000 {
 
 			ranges = <0 0 0x14680000 0x40000>;
 
+			minidump_config: minidump-sram@1c {
+				reg = <0x1c 0x4>;
+			};
+
 			ipa_modem_tables: modem-tables@3d000 {
 				reg = <0x3d000 0x2000>;
 			};
-- 
2.53.0