[PATCH v6 0/4] arm64: qcom: add Ayaneo Pocket DS gaming console

[PATCH v6 0/4] arm64: qcom: add Ayaneo Pocket DS gaming console

[Alexandre Hamamdjian via B4 Relay]

This series adds initial support for the Ayaneo Pocket DS, a handheld
gaming console built around the Qualcomm QCS8550 SoC. It has UFS
storage, WiFi/Bluetooth, gaming buttons, microSD, and USB-C with
DisplayPort. Game controls are exposed through a Renesas uPD720201
PCIe USB 3.0 host controller hung off PCIe1, while a dedicated gamepad
MCU is reached over UART11.

The series is structured as:

  1. dt-bindings entry for the new ayaneo,pocket-ds compatible.
  2. sm8550.dtsi: add the QUP2 SE3 (UART11) controller node and its
     default pinctrl, so the board can enable it as &uart11.
  3. The Pocket DS board device tree itself, together with thermal_*
     labels for the cpuss/cpu/gpuss thermal zones added to sm8550.dtsi
     so the board has a real user of them in the same patch.

Only the basics are wired up at this stage (boot to console, core
peripherals, USB-C with DP and SBU AUX muxing, microSD, WiFi/BT,
gaming controls, volume keys, the RGB power LED and PWM-fan cooling),
plus the lower DSI panel in patch 4.

The upper panel is still missing. Its Chipone ICNA3512 binding makes
disp-supply and blvdd-supply mandatory, and this board has no
separately controllable rail for either: the vendor device tree drives
the upper panel through a platform enable GPIO and points the panel
node at the simulator supply list, and holding that GPIO low on the
device does not stop the panel initialising. It will follow once the
wiring is confirmed.

Signed-off-by: Alexandre Hamamdjian <azkali.limited@gmail.com>
---
Changes in v6:
- board dts: renamed the uart11 alias from hsuart0 to serial2. uart11 is
  a plain serial engine like uart7 and uart14; hsuart0 in-tree only
  labels the sc7180/trogdor Bluetooth UART (Konrad).
- board dts: dropped output-low from the fan_pwr_active pinctrl state.
  vdd_fan_5v0 is a regulator-fixed with gpios = <&tlmm 31 ...>, so the
  gpiod API already drives the pin (Konrad).
- board dts: reordered the codec node before cpu in both dai-links of
  the sound node (Konrad).
- board dts: kept output-high on the gamepad_pwr_en pinctrl state.
  Unlike fan_pwr_active, gpio52 has no GPIO consumer anywhere in the
  device tree, so pinctrl is the only thing asserting it; dropping it
  leaves the uPD720201 gamepad host controller unpowered. This mirrors
  the already-merged sm8650-ayaneo-pocket-s2.dts and reverses a v4
  removal that v5 restored. Happy to model it as a fixed regulator
  instead if that is preferred.
- Rebased onto next-20260824. Three fallouts from the newer base, all in
  the board dts:
    * &pcieport0 is now &pcie0_port0 in sm8550.dtsi.
    * the uPD720201 node moved from an inline pcie@0 child of &pcie1 to
      the &pcie1_port0 label, matching sm8650-ayaneo-pocket-s2.
    * &ipa now carries memory-region = <&ipa_fw_mem>, so deleting the
      ipa_fw_mem reserved-memory node left a dangling phandle and dtc
      refused to build. Added /delete-property/ memory-region on &ipa,
      the same treatment &remoteproc_mpss and &remoteproc_cdsp already
      get; &ipa is status = "disabled" on this board.
- board dts: added the RGB power LED under &pm8550_pwm, shaped like the
  multi-led node already in sm8650-ayaneo-pocket-s2.
- New patch 4/4 adding the lower DSI panel (ST7703 + SGM3804 + SY7758 +
  TCA6408 rails). It is kept separate because it depends on four
  bindings that only reached linux-next recently, so patches 1-3 can be
  applied without waiting for them.
- Picked up Konrad's Reviewed-by on the board dts patch. It predates the
  RGB LED node above; happy to drop it if you would rather re-review.
- Link to v5: https://patch.msgid.link/20260723-pocketds-v5-0-74508388c716@gmail.com

Changes in v5:
- Restore output-high on the gamepad_pwr_en pinctrl state: the Renesas
  uPD720201 gamepad host controller power-enable on gpio52 must be
  driven high. It was dropped in v4 together with the boot-time
  output-high states, but unlike those it is a functional enable
  rather than a downstream boot artefact (Sashiko).
- Link to v4: https://patch.msgid.link/20260722-pocketds-v4-0-438704cd51f7@gmail.com

Changes in v4:
- Reordered the series so the sm8550.dtsi UART11 patch comes before the
  board dts that consumes &uart11, keeping the tree bisectable (Dmitry).
- Renamed the board compatible from "ayaneo,pocketds" to
  "ayaneo,pocket-ds", matching the hyphenated "ayaneo,pocket-s2" already
  in qcom.yaml and the DT compatible naming convention (Sashiko). The
  Acked-by on the bindings patch was given for the unhyphenated string;
  kept it since the change is a one-word rename, please shout if you
  would rather re-ack it.
- uart11: switched operating-points-v2 to &qup_opp_table_120mhz, which
  is what i2c11 and spi11 use for the very same serial engine at
  0x88c000; the 100 MHz table was simply wrong (Sashiko).
- uart11: use bias-pull-up rather than bias-disable on TX/RX, matching
  qup_uart14_default, the other high-speed UART on this SoC (Sashiko).
- Reworded the UART11 commit message, which implied that open-coding
  the controller in a board dts was a viable alternative (Konrad).
- Squashed the sm8550.dtsi thermal-zone labels patch into the board
  dts patch so the labels gain their consumer in the same change
  (Krzysztof).
- Renamed the sm8550.dtsi thermal-zone labels from
  cpuss[0-3]_thermal / cpu7_top_thermal / gpuss[0-7]_thermal to
  thermal_cpuss[0-3] / thermal_cpu7_top / thermal_gpuss[0-7] so all
  thermal-related overrides cluster alphabetically in the consuming
  board dts (Dmitry).
- Dropped the &gpu_opp_table override until upstream gains proper
  speed-bin detection (Dmitry).
- Switched remoteproc_adsp firmware-name from the downstream .mdt
  suffix to the upstream .mbn convention (Dmitry).
- Replaced the /delete-node/ overrides on &remoteproc_mpss /
  &remoteproc_cdsp with /delete-property/ memory-region (Dmitry). Both
  are already status="disabled" in sm8550.dtsi, so the nodes never
  needed deleting; only their now-dangling memory-region phandles did.
  The reserved-memory regions for the unused modem, CDSP, camera and
  IPA firmware stay /delete-node/-ed so that memory is handed back to
  Linux, matching what sm8550-samsung-q5q and
  sm8550-sony-xperia-yodo-pdx234 already do on this SoC.
- Dropped the downstream rocknix-u-boot-dt-id root property (Neil).
- Switched the deprecated "gpio" property to "gpios" on all fixed
  regulators (Neil).
- Reworked the audio-routing DAPM table to drop the bogus
  "VA DMIC0/1, vdd-micb" routes (Neil).
- Reshaped the per-zone thermal-zones overrides to a single "active"
  trip point bound to &pwm_fan via cooling-maps, mirroring the
  Ayaneo Pocket S2 style (Neil).
- Added a pinctrl-1 sleep state for pwm_fan and the corresponding
  fan_pwm_sleep PMIC pinctrl entry (Neil).
- Added a gpio-keys node wiring up the Volume Up button via the
  previously-unreferenced volume_up_n pinctrl (Neil).
- Dropped every output-high in the &tlmm pinctrl states (Neil).
- Dropped the incomplete DSI/panel bring-up (display_panel, &mdss_dsi0,
  &mdss_dsi0_phy, &mdss_dsi1, &mdss_dsi1_out, &mdss_dsi1_phy and the
  sde_dsi*/sde_te*/panel_pwr_active pinctrl) until the panel bindings
  are reviewed (Neil).
- Added the missing SBU AUX endpoint between the pmic-glink connector
  and the NB7VPQ904M redriver port@2 to complete the DP altmode
  signal path (Neil).
- Normalised the last fixed-regulator node name to the "<name>-regulator"
  convention (vph_pwr) (Krzysztof).
- Reauthored the bindings patch under Alexandre alone (no co-developed
  needed for the trivial DT entry) and picked up Krzysztof's Acked-by.
- Fixed the sign-off chain on the board dts patch: the From: author's
  Signed-off-by now comes first and the submitter's last (Krzysztof).
- No qup_uart11_cts_rts pinctrl state was added: nothing in-tree
  references it, and hardware flow control is not wired on this board.
  It can be added together with its first user (Sashiko).
- Built with "make CHECK_DTBS=yes qcom/qcs8550-ayaneo-pocket-ds.dtb":
  no errors, no warnings. With W=1 dtc additionally reports
  avoid_unnecessary_addr_size on sm8550.dtsi's dsi@ae94000/dsi@ae96000,
  because no panel child is added while display support is deferred;
  qcs8550-aim300-aiot already reports the same for dsi@ae96000.
- board dts: enabled &pcie0_phy and added the &pcieport0 wifi@0 supply
  node for the WCN7850. Without the PCIe0 PHY and the vddpcie0p9 /
  vddpcie1p8 rails the WiFi link never trained; the wifi@0 supply node
  follows sm8650-ayaneo-pocket-s2 and the sm8550/sm8650 QRD/HDK boards.
- board dts: dropped &i2c4 to 100 kHz. The FT5426 touchscreen
  clock-stretches past the GENI controller's timeout at 400 kHz, and
  the qcom-geni-i2c controller has no i2c_bus_recovery, so a stuck SCL
  can only be cleared by an FSM reset that is itself the operation
  timing out. Standard mode is within the FT5426's clock-stretch spec.
- board dts: pinned &pcie0 to max-link-speed = <2> (Gen2), the link
  speed validated for the WCN7850 on this board.
- board dts: dropped the undocumented sdhci-caps-mask = <0x3 0x0> on
  &sdhc_2 (it masked the SDR50/SDR104 capability bits that the board's
  own sd-uhs-sdr50 / sd-uhs-sdr104 properties enable). qcom,dll-config
  is kept, with its derivation now recorded in the commit message.
- Renamed the board dts to qcs8550-ayaneo-pocket-ds.dts to match the
  hyphenated compatible and the sibling sm8650-ayaneo-pocket-s2.dts;
  the Makefile entry and the CHECK_DTBS target were updated to suit.
- Note on the UART11 Reviewed-by: Konrad's tag was given on v3, before
  the operating-points-v2 (&qup_opp_table_120mhz) and bias-pull-up
  changes above. It is retained here; happy to drop it for a re-review.
- Link to v3: https://patch.msgid.link/20260517-pocketds-v3-0-d5910c801756@gmail.com

Changes in v3:
- New prerequisite patch adding the QUP2 SE3 (UART11) controller node
  and the qup_uart11_default pinctrl state to sm8550.dtsi, so the
  board can enable the gamepad MCU UART via &uart11 instead of
  duplicating the controller node in the board dts.
- Alphabetised the root-level nodes in the board dts and renamed the
  fixed regulators to the "<name>-regulator" node-name convention.
- Link to v2: https://patch.msgid.link/20260511-pocketds-v2-0-299dd4247f2f@gmail.com

Changes in v2:
- Inlined the board into a single qcs8550-ayaneo-pocketds.dts, matching
  the sm8650-ayaneo-pocket-s2 layout
- Added qcom,qcs8550 to the compatible chain
- Prerequisite patch labelling the sm8550 thermal zones so the board
  can extend them via &label overrides (and refactored the board's
  thermal-zones to use them)
- Added the Renesas uPD720201 USB 3.0 controller as a child of pcie1
  with proper avdd33 / vdd10 / vdd33 regulators
- Moved gamepad_pwr_en off &pcie1's pinctrl-0 and onto the
  usb-controller node
- Split the lumped upd720201_active pinctrl into per-regulator states
- Fixed mdss_dp0_out data-lanes to <0 1 2 3> (all four wired)
- Fixed gpio-reserved-ranges to <32 4> (gpio 38-39 drive the Goodix
  touchscreen)
- Renamed nodes with underscores (llcc-lpi-region, splash-region,
  gpio@20) per DT conventions
- Reordered pinctrl-names after pinctrl-N file-wide
- Dropped the unused cont_splash_region label
- Link to v1: https://patch.msgid.link/20260510-pocketds-v1-0-cf05acec06af@gmail.com

To: Bjorn Andersson <andersson@kernel.org>
To: Konrad Dybcio <konradybcio@kernel.org>
To: Rob Herring <robh@kernel.org>
To: Krzysztof Kozlowski <krzk+dt@kernel.org>
To: Conor Dooley <conor+dt@kernel.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org

---
Alexandre Hamamdjian (3):
      dt-bindings: arm: qcom: document the Ayaneo Pocket DS
      arm64: dts: qcom: sm8550: add UART11 node
      arm64: dts: qcom: qcs8550-ayaneo-pocket-ds: add the lower DSI panel

Teguh Sobirin (1):
      arm64: dts: qcom: add basic devicetree for Ayaneo Pocket DS gaming console

 Documentation/devicetree/bindings/arm/qcom.yaml    |    1 +
 arch/arm64/boot/dts/qcom/Makefile                  |    1 +
 .../boot/dts/qcom/qcs8550-ayaneo-pocket-ds.dts     | 1742 ++++++++++++++++++++
 arch/arm64/boot/dts/qcom/sm8550.dtsi               |   52 +-
 4 files changed, 1783 insertions(+), 13 deletions(-)
---
base-commit: 4b18edbd8e70f7e6860d56370f13244896d0f95c
change-id: 20260510-pocketds-e0e7b99cf369

Best regards,
--  
Alexandre Hamamdjian <azkali.limited@gmail.com>

[PATCH v6 1/4] dt-bindings: arm: qcom: document the Ayaneo Pocket DS

[Alexandre Hamamdjian via B4 Relay]

From: Alexandre Hamamdjian <azkali.limited@gmail.com>

Document the Qualcomm QCS8550 based Ayaneo Pocket DS gaming console.

Signed-off-by: Alexandre Hamamdjian <azkali.limited@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
---
 Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index ff8a35df7862..6ff28b86bfe6 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -1154,6 +1154,7 @@ properties:
 
       - items:
           - enum:
+              - ayaneo,pocket-ds
               - qcom,qcs8550-rb5gen2
           - const: qcom,qcs8550
           - const: qcom,sm8550

-- 
2.55.0

[PATCH v6 2/4] arm64: dts: qcom: sm8550: add UART11 node

[Alexandre Hamamdjian via B4 Relay]

From: Alexandre Hamamdjian <azkali.limited@gmail.com>

Add the QUPv3_2 SE3 UART (UART11) controller node and its default
pinctrl state to sm8550.dtsi, so boards with a peripheral wired to
that serial engine can enable it through &uart11.

The serial engine at 0x88c000 is already described as i2c11 and spi11,
so the UART node takes the same qup_opp_table_120mhz they use: it is
the same block behind the same GCC_QUPV3_WRAP2_S3_CLK, and its core
clock tops out at 120 MHz rather than the 100 MHz the other table
allows. TX and RX are biased pull-up, matching qup_uart14_default, so
the lines idle high on boards that do not fit external pull-ups.

Signed-off-by: Alexandre Hamamdjian <azkali.limited@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/sm8550.dtsi | 26 ++++++++++++++++++++++++++
 1 file changed, 26 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8550.dtsi b/arch/arm64/boot/dts/qcom/sm8550.dtsi
index 0e701e709235..fcbcf22ff951 100644
--- a/arch/arm64/boot/dts/qcom/sm8550.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8550.dtsi
@@ -1442,6 +1442,24 @@ &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ACTIVE_ONLY>,
 				status = "disabled";
 			};
 
+			uart11: serial@88c000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x0088c000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
+				interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH 0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart11_default>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>,
+						<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ACTIVE_ONLY
+						 &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ACTIVE_ONLY>;
+				interconnect-names = "qup-core", "qup-config";
+				operating-points-v2 = <&qup_opp_table_120mhz>;
+				power-domains = <&rpmhpd RPMHPD_CX>;
+				status = "disabled";
+			};
+
 			i2c12: i2c@890000 {
 				compatible = "qcom,geni-i2c";
 				reg = <0 0x00890000 0 0x4000>;
@@ -5478,6 +5496,14 @@ qup_uart7_default: qup-uart7-default-state {
 				bias-disable;
 			};
 
+			qup_uart11_default: qup-uart11-default-state {
+				/* TX, RX */
+				pins = "gpio70", "gpio71";
+				function = "qup2_se3";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
 			qup_uart14_default: qup-uart14-default-state {
 				/* TX, RX */
 				pins = "gpio78", "gpio79";

-- 
2.55.0

[PATCH v6 3/4] arm64: dts: qcom: add basic devicetree for Ayaneo Pocket DS gaming console

[Alexandre Hamamdjian via B4 Relay]

From: Teguh Sobirin <teguh@sobir.in>

Add initial Device Tree for the Ayaneo Pocket DS gaming console based
on the Qualcomm QCS8550 platform.

The design is similar to a phone without the modem: game controls are
exposed through a Renesas uPD720201 PCIe USB 3.0 host controller hung
off PCIe1, while a dedicated gamepad MCU is reached over UART11.
DisplayPort is muxed over the USB-C connector with all four lanes
wired, with an ON Semi NB7VPQ904M redriver handling SS and SBU AUX
muxing.

Only the basics are wired up at this stage (boot to console, core
peripherals, USB-C and DP, microSD, WiFi/BT, gaming controls); DSI
panel support will follow in a later submission once the panel
bindings are reviewed.

The FT5426 touchscreen on i2c4 clock-stretches past the GENI
controller's timeout at 400 kHz. The qcom-geni-i2c controller
implements no i2c_bus_recovery, so a stuck SCL can only be cleared by
an FSM reset, which is itself the operation that times out. i2c4 is
therefore run at 100 kHz, well within the FT5426's clock-stretch
tolerance and with ample bandwidth for its sub-256-byte reports.

PCIe0 hosts the WCN7850 WiFi and is pinned to Gen2 (max-link-speed =
<2>), the link speed validated on this board.

sdhc_2 sets qcom,dll-config to 0x0007442c, the DLL_CONFIG value the
QCS8550 vendor device tree ships for this SDCC2 instance, in place of
the generic sm8550 default of 0x0007642c; the vendor value is the one
validated for SDR104 operation on this board.

The board uses the &thermal_cpuss[0-3], &thermal_cpu7_top and
&thermal_gpuss[0-7] labels to extend the SoC thermal zones with an
active trip point and a cooling map driving the on-board PWM fan;
those labels are added to sm8550.dtsi as part of this change so the
board has a real user from the same patch.

Signed-off-by: Teguh Sobirin <teguh@sobir.in>
Co-developed-by: Alexandre Hamamdjian <azkali.limited@gmail.com>
Signed-off-by: Alexandre Hamamdjian <azkali.limited@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/Makefile                  |    1 +
 .../boot/dts/qcom/qcs8550-ayaneo-pocket-ds.dts     | 1645 ++++++++++++++++++++
 arch/arm64/boot/dts/qcom/sm8550.dtsi               |   26 +-
 3 files changed, 1659 insertions(+), 13 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 1c86e7e98f55..9bdea2e8ec05 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -193,6 +193,7 @@ qcs8300-ride-el2-dtbs := qcs8300-ride.dtb monaco-el2.dtbo
 
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs8300-ride-el2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs8550-aim300-aiot.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= qcs8550-ayaneo-pocket-ds.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs8550-rb5gen2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs9100-ride.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs9100-ride-r3.dtb
diff --git a/arch/arm64/boot/dts/qcom/qcs8550-ayaneo-pocket-ds.dts b/arch/arm64/boot/dts/qcom/qcs8550-ayaneo-pocket-ds.dts
new file mode 100644
index 000000000000..09b1c86cc3d3
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/qcs8550-ayaneo-pocket-ds.dts
@@ -0,0 +1,1645 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2025, Teguh Sobirin.
+ * Copyright (c) 2025, ROCKNIX (https://github.com/ROCKNIX)
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "qcs8550.dtsi"
+#include "pm8550.dtsi"
+#include "pm8550b.dtsi"
+#define PMK8550VE_SID 5
+#include "pm8550ve.dtsi"
+#include "pm8550vs.dtsi"
+#include "pmk8550.dtsi"
+
+/delete-node/ &aop_image_mem;
+/delete-node/ &aop_config_mem;
+/delete-node/ &camera_mem;
+/delete-node/ &ipa_fw_mem;
+/delete-node/ &ipa_gsi_mem;
+/delete-node/ &mpss_dsm_mem;
+/delete-node/ &mpss_mem;
+/delete-node/ &q6_mpss_dtb_mem;
+/delete-node/ &cdsp_mem;
+/delete-node/ &q6_cdsp_dtb_mem;
+
+/ {
+	model = "AYANEO Pocket DS";
+	compatible = "ayaneo,pocket-ds", "qcom,qcs8550", "qcom,sm8550";
+
+	aliases {
+		serial0 = &uart7;
+		serial1 = &uart14;
+		serial2 = &uart11;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&volume_up_n>;
+		pinctrl-names = "default";
+
+		key-volume-up {
+			label = "Volume Up";
+			linux,code = <KEY_VOLUMEUP>;
+			gpios = <&pm8550_gpios 6 GPIO_ACTIVE_LOW>;
+			debounce-interval = <15>;
+		};
+	};
+
+	pmic-glink {
+		compatible = "qcom,sm8550-pmic-glink", "qcom,pmic-glink";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		orientation-gpios = <&tlmm 11 GPIO_ACTIVE_HIGH>;
+
+		connector@0 {
+			compatible = "usb-c-connector";
+
+			reg = <0>;
+
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_hs_in: endpoint {
+						remote-endpoint = <&usb_1_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss_in: endpoint {
+						remote-endpoint = <&redriver_ss_out>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+
+					pmic_glink_sbu: endpoint {
+						remote-endpoint = <&redriver_sbu>;
+					};
+				};
+			};
+		};
+	};
+
+	pwm_fan: pwm-fan {
+		compatible = "pwm-fan";
+
+		pinctrl-0 = <&fan_pwm_active>, <&fan_int>;
+		pinctrl-1 = <&fan_pwm_sleep>, <&fan_int>;
+		pinctrl-names = "default", "sleep";
+
+		fan-supply = <&vdd_fan_5v0>;
+		pwms = <&pm8550_pwm 3 40000>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <64 IRQ_TYPE_EDGE_FALLING>;
+
+		#cooling-cells = <2>;
+		cooling-levels = <0 30 45 60 70 90 120 150>;
+	};
+
+	reserved-memory {
+		hyp_mem: hyp-region@80000000 {
+			reg = <0 0x80000000 0 0xa00000>;
+			no-map;
+		};
+
+		cpusys_vm_mem: cpusys-vm-region@80a00000 {
+			reg = <0 0x80a00000 0 0x400000>;
+			no-map;
+		};
+
+		hyp_tags_mem: hyp-tags-region@80e00000 {
+			reg = <0 0x80e00000 0 0x3d0000>;
+			no-map;
+		};
+
+		xbl_sc_mem: xbl-sc-region@d8100000 {
+			reg = <0 0xd8100000 0 0x40000>;
+			no-map;
+		};
+
+		hyp_tags_reserved_mem: hyp-tags-reserved-region@811d0000 {
+			reg = <0 0x811d0000 0 0x30000>;
+			no-map;
+		};
+
+		xbl_dt_log_merged_mem: xbl-dt-log-merged-region@81a00000 {
+			reg = <0 0x81a00000 0 0x260000>;
+			no-map;
+		};
+
+		aop_config_merged_mem: aop-config-merged-region@81c80000 {
+			reg = <0 0x81c80000 0 0x74000>;
+			no-map;
+		};
+
+		chipinfo_mem: chipinfo-region@81cf4000 {
+			reg = <0 0x81cf4000 0 0x1000>;
+			no-map;
+		};
+
+		global_sync_mem: global-sync-region@82600000 {
+			reg = <0 0x82600000 0 0x100000>;
+			no-map;
+		};
+
+		tz_stat_mem: tz-stat-region@82700000 {
+			reg = <0 0x82700000 0 0x100000>;
+			no-map;
+		};
+
+		cpucp_fw_mem: cpucp-fw-region@d8140000 {
+			reg = <0 0xd8140000 0 0x1c0000>;
+			no-map;
+		};
+
+		qtee_mem: qtee-region@d8300000 {
+			reg = <0 0xd8300000 0 0x500000>;
+			no-map;
+		};
+
+		hwfence_shbuf: hwfence-shbuf-region@e6440000 {
+			reg = <0 0xe6440000 0 0x2dd000>;
+			no-map;
+		};
+
+		hyp_ext_reserved_mem: hyp-ext-reserved-region@ff700000 {
+			reg = <0 0xff700000 0 0x100000>;
+			no-map;
+		};
+
+		llcc_lpi_mem: llcc-lpi-region@ff800000 {
+			reg = <0 0xff800000 0 0x600000>;
+			no-map;
+		};
+
+		hyp_ext_tags_mem: hyp-ext-tags-region@fce00000 {
+			reg = <0 0xfce00000 0 0x2900000>;
+			no-map;
+		};
+
+		splash_region: splash-region@b8000000 {
+			reg = <0x0 0xb8000000 0x0 0x2b00000>;
+			no-map;
+		};
+	};
+
+	sound {
+		compatible = "qcom,sm8550-sndcard", "qcom,sm8450-sndcard";
+		model = "SM8550-APS";
+
+		audio-routing = "SpkrLeft IN", "WSA_SPK1 OUT",
+				"SpkrRight IN", "WSA_SPK2 OUT";
+
+		wsa-dai-link {
+			link-name = "WSA Playback";
+
+			codec {
+				sound-dai = <&spk_amp_l>,
+					    <&spk_amp_r>,
+					    <&swr0 0>,
+					    <&lpass_wsamacro 0>;
+			};
+
+			cpu {
+				sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		va-dai-link {
+			link-name = "VA Capture";
+
+			codec {
+				sound-dai = <&lpass_vamacro 0>;
+			};
+
+			cpu {
+				sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+	};
+
+	tca6424_vcc: tca6424-vcc-regulator {
+		compatible = "regulator-fixed";
+
+		regulator-name = "tca6424_vcc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&tlmm 168 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-boot-on;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	upd720201_avdd33_reg: upd720201-avdd33-regulator {
+		compatible = "regulator-fixed";
+
+		regulator-name = "upd720201_avdd33";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&tlmm 10 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		vin-supply = <&vph_pwr>;
+
+		pinctrl-0 = <&upd720201_avdd33>;
+		pinctrl-names = "default";
+	};
+
+	upd720201_vdd10_reg: upd720201-vdd10-regulator {
+		compatible = "regulator-fixed";
+
+		regulator-name = "upd720201_vdd10";
+		regulator-min-microvolt = <1050000>;
+		regulator-max-microvolt = <1050000>;
+
+		gpios = <&tlmm 13 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		vin-supply = <&vph_pwr>;
+
+		pinctrl-0 = <&upd720201_vdd10>;
+		pinctrl-names = "default";
+	};
+
+	upd720201_vdd33_reg: upd720201-vdd33-regulator {
+		compatible = "regulator-fixed";
+
+		regulator-name = "upd720201_vdd33";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&tlmm 18 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		vin-supply = <&vph_pwr>;
+
+		pinctrl-0 = <&upd720201_vdd33>;
+		pinctrl-names = "default";
+	};
+
+	vdd_fan_5v0: vdd-fan-5v0-regulator {
+		compatible = "regulator-fixed";
+
+		regulator-name = "vdd_fan_5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		gpios = <&tlmm 31 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&fan_pwr_active>;
+		pinctrl-names = "default";
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	vdd_ts: vdd-ts-regulator {
+		compatible = "regulator-fixed";
+
+		regulator-name = "vdd_ts_en";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&tca6408 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	wcn7850-pmu {
+		compatible = "qcom,wcn7850-pmu";
+
+		pinctrl-0 = <&wlan_en>, <&bt_default>, <&pmk8550_sleep_clk>;
+		pinctrl-names = "default";
+
+		wlan-enable-gpios = <&tlmm 80 GPIO_ACTIVE_HIGH>;
+		bt-enable-gpios = <&tlmm 81 GPIO_ACTIVE_HIGH>;
+
+		vdd-supply = <&vreg_s5g_0p85>;
+		vddio-supply = <&vreg_l15b_1p8>;
+		vddaon-supply = <&vreg_s2g_0p85>;
+		vdddig-supply = <&vreg_s4e_0p95>;
+		vddrfa1p2-supply = <&vreg_s4g_1p25>;
+		vddrfa1p8-supply = <&vreg_s6g_1p86>;
+
+		regulators {
+			vreg_pmu_rfa_cmn: ldo0 {
+				regulator-name = "vreg_pmu_rfa_cmn";
+			};
+
+			vreg_pmu_aon_0p59: ldo1 {
+				regulator-name = "vreg_pmu_aon_0p59";
+			};
+
+			vreg_pmu_wlcx_0p8: ldo2 {
+				regulator-name = "vreg_pmu_wlcx_0p8";
+			};
+
+			vreg_pmu_wlmx_0p85: ldo3 {
+				regulator-name = "vreg_pmu_wlmx_0p85";
+			};
+
+			vreg_pmu_btcmx_0p85: ldo4 {
+				regulator-name = "vreg_pmu_btcmx_0p85";
+			};
+
+			vreg_pmu_rfa_0p8: ldo5 {
+				regulator-name = "vreg_pmu_rfa_0p8";
+			};
+
+			vreg_pmu_rfa_1p2: ldo6 {
+				regulator-name = "vreg_pmu_rfa_1p2";
+			};
+
+			vreg_pmu_rfa_1p8: ldo7 {
+				regulator-name = "vreg_pmu_rfa_1p8";
+			};
+
+			vreg_pmu_pcie_0p9: ldo8 {
+				regulator-name = "vreg_pmu_pcie_0p9";
+			};
+
+			vreg_pmu_pcie_1p8: ldo9 {
+				regulator-name = "vreg_pmu_pcie_1p8";
+			};
+		};
+	};
+};
+
+&apps_rsc {
+	regulators-0 {
+		compatible = "qcom,pm8550-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vdd-bob1-supply = <&vph_pwr>;
+		vdd-bob2-supply = <&vph_pwr>;
+		vdd-l1-l4-l10-supply = <&vreg_s6g_1p86>;
+		vdd-l2-l13-l14-supply = <&vreg_bob1>;
+		vdd-l3-supply = <&vreg_s4g_1p25>;
+		vdd-l5-l16-supply = <&vreg_bob1>;
+		vdd-l6-l7-supply = <&vreg_bob1>;
+		vdd-l8-l9-supply = <&vreg_bob1>;
+		vdd-l11-supply = <&vreg_s4g_1p25>;
+		vdd-l12-supply = <&vreg_s6g_1p86>;
+		vdd-l15-supply = <&vreg_s6g_1p86>;
+		vdd-l17-supply = <&vreg_bob2>;
+
+		vreg_bob1: bob1 {
+			regulator-name = "vreg_bob1";
+			regulator-min-microvolt = <3296000>;
+			regulator-max-microvolt = <3960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_bob2: bob2 {
+			regulator-name = "vreg_bob2";
+			regulator-min-microvolt = <2720000>;
+			regulator-max-microvolt = <3960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2b_3p0: ldo2 {
+			regulator-name = "vreg_l2b_3p0";
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5b_3p1: ldo5 {
+			regulator-name = "vreg_l5b_3p1";
+			regulator-min-microvolt = <3104000>;
+			regulator-max-microvolt = <3104000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6b_1p8: ldo6 {
+			regulator-name = "vreg_l6b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7b_1p8: ldo7 {
+			regulator-name = "vreg_l7b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8b_1p8: ldo8 {
+			regulator-name = "vreg_l8b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9b_2p9: ldo9 {
+			regulator-name = "vreg_l9b_2p9";
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l10b_1p8: ldo10 {
+			regulator-name = "vreg_l10b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l11b_1p2: ldo11 {
+			regulator-name = "vreg_l11b_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1504000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l12b_1p8: ldo12 {
+			regulator-name = "vreg_l12b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l13b_3p0: ldo13 {
+			regulator-name = "vreg_l13b_3p0";
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l14b_3p2: ldo14 {
+			regulator-name = "vreg_l14b_3p2";
+			regulator-min-microvolt = <3200000>;
+			regulator-max-microvolt = <3200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l15b_1p8: ldo15 {
+			regulator-name = "vreg_l15b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l16b_2p8: ldo16 {
+			regulator-name = "vreg_l16b_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l17b_2p5: ldo17 {
+			regulator-name = "vreg_l17b_2p5";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <2504000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,pm8550vs-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vdd-l1-supply = <&vreg_s4g_1p25>;
+		vdd-l2-supply = <&vreg_s4e_0p95>;
+		vdd-l3-supply = <&vreg_s4e_0p95>;
+
+		vreg_l3c_0p9: ldo3 {
+			regulator-name = "vreg_l3c_0p9";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-2 {
+		compatible = "qcom,pm8550vs-rpmh-regulators";
+		qcom,pmic-id = "d";
+
+		vdd-l1-supply = <&vreg_s4e_0p95>;
+		vdd-l2-supply = <&vreg_s4e_0p95>;
+		vdd-l3-supply = <&vreg_s4e_0p95>;
+
+		vreg_l1d_0p88: ldo1 {
+			regulator-name = "vreg_l1d_0p88";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-3 {
+		compatible = "qcom,pm8550vs-rpmh-regulators";
+		qcom,pmic-id = "e";
+
+		vdd-l1-supply = <&vreg_s4e_0p95>;
+		vdd-l2-supply = <&vreg_s4e_0p95>;
+		vdd-l3-supply = <&vreg_s4g_1p25>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+
+		vreg_s4e_0p95: smps4 {
+			regulator-name = "vreg_s4e_0p95";
+			regulator-min-microvolt = <904000>;
+			regulator-max-microvolt = <984000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s5e_1p08: smps5 {
+			regulator-name = "vreg_s5e_1p08";
+			regulator-min-microvolt = <1010000>;
+			regulator-max-microvolt = <1120000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1e_0p88: ldo1 {
+			regulator-name = "vreg_l1e_0p88";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2e_0p9: ldo2 {
+			regulator-name = "vreg_l2e_0p9";
+			regulator-min-microvolt = <904000>;
+			regulator-max-microvolt = <970000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3e_1p2: ldo3 {
+			regulator-name = "vreg_l3e_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-4 {
+		compatible = "qcom,pm8550ve-rpmh-regulators";
+		qcom,pmic-id = "f";
+
+		vdd-l1-supply = <&vreg_s4e_0p95>;
+		vdd-l2-supply = <&vreg_s4e_0p95>;
+		vdd-l3-supply = <&vreg_s4e_0p95>;
+		vdd-s4-supply = <&vph_pwr>;
+
+		vreg_s4f_0p5: smps4 {
+			regulator-name = "vreg_s4f_0p5";
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <700000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1f_0p9: ldo1 {
+			regulator-name = "vreg_l1f_0p9";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2f_0p88: ldo2 {
+			regulator-name = "vreg_l2f_0p88";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3f_0p88: ldo3 {
+			regulator-name = "vreg_l3f_0p88";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-5 {
+		compatible = "qcom,pm8550vs-rpmh-regulators";
+		qcom,pmic-id = "g";
+
+		vdd-l1-supply = <&vreg_s4g_1p25>;
+		vdd-l2-supply = <&vreg_s4g_1p25>;
+		vdd-l3-supply = <&vreg_s4g_1p25>;
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+
+		vreg_s1g_1p25: smps1 {
+			regulator-name = "vreg_s1g_1p25";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s2g_0p85: smps2 {
+			regulator-name = "vreg_s2g_0p85";
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <1000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s3g_0p8: smps3 {
+			regulator-name = "vreg_s3g_0p8";
+			regulator-min-microvolt = <300000>;
+			regulator-max-microvolt = <1004000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s4g_1p25: smps4 {
+			regulator-name = "vreg_s4g_1p25";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1352000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s5g_0p85: smps5 {
+			regulator-name = "vreg_s5g_0p85";
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1004000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s6g_1p86: smps6 {
+			regulator-name = "vreg_s6g_1p86";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1g_1p2: ldo1 {
+			regulator-name = "vreg_l1g_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3g_1p2: ldo3 {
+			regulator-name = "vreg_l3g_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+};
+
+&gpi_dma1 {
+	status = "okay";
+};
+
+&gpi_dma2 {
+	status = "okay";
+};
+
+&gpu {
+	status = "okay";
+};
+
+&gpu_zap_shader {
+	firmware-name = "qcom/sm8550/a740_zap.mbn";
+};
+
+&i2c0 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	tca6408: gpio@20 {
+		compatible = "ti,tca6408";
+		reg = <0x20>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		vcc-supply = <&tca6424_vcc>;
+	};
+};
+
+&i2c2 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	touchscreen@5d {
+		compatible = "goodix,gt911";
+		reg = <0x5d>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <39 IRQ_TYPE_EDGE_FALLING>;
+
+		reset-gpios = <&tlmm 38 GPIO_ACTIVE_HIGH>;
+		irq-gpios = <&tlmm 39 GPIO_ACTIVE_HIGH>;
+
+		VDDIO-supply = <&vdd_ts>;
+
+		pinctrl-0 = <&ts2_reset>, <&ts2_irq>;
+		pinctrl-names = "default";
+
+		touchscreen-size-x = <768>;
+		touchscreen-size-y = <1024>;
+	};
+};
+
+&i2c4 {
+	clock-frequency = <100000>;
+
+	status = "okay";
+
+	touchscreen: touchscreen@38 {
+		compatible = "focaltech,ft5426";
+		reg = <0x38>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+
+		reset-gpios = <&tlmm 24 GPIO_ACTIVE_LOW>;
+
+		vcc-supply = <&vreg_l14b_3p2>;
+		iovcc-supply = <&vreg_l12b_1p8>;
+
+		pinctrl-0 = <&ts_int_default &ts_rst_default>;
+		pinctrl-1 = <&ts_int_sleep &ts_rst_sleep>;
+		pinctrl-names = "default", "sleep";
+
+		touchscreen-size-x = <1080>;
+		touchscreen-size-y = <1920>;
+	};
+};
+
+&i2c_hub_2 {
+	status = "okay";
+
+	typec-retimer@1c {
+		compatible = "onnn,nb7vpq904m";
+		reg = <0x1c>;
+
+		vcc-supply = <&vreg_l15b_1p8>;
+
+		retimer-switch;
+		orientation-switch;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				redriver_ss_out: endpoint {
+					remote-endpoint = <&pmic_glink_ss_in>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				redriver_ss_in: endpoint {
+					data-lanes = <3 2 1 0>;
+					remote-endpoint = <&usb_dp_qmpphy_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				redriver_sbu: endpoint {
+					remote-endpoint = <&pmic_glink_sbu>;
+				};
+			};
+		};
+	};
+};
+
+&i2c_master_hub_0 {
+	status = "okay";
+};
+
+&ipa {
+	/delete-property/ memory-region;
+};
+
+&iris {
+	status = "okay";
+};
+
+/* DMIC 01 23 */
+&lpass_vamacro {
+	pinctrl-0 = <&dmic01_default>, <&dmic23_default>;
+	pinctrl-names = "default";
+
+	vdd-micb-supply = <&vreg_l10b_1p8>;
+
+	qcom,dmic-sample-rate = <4800000>;
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_dp0 {
+	status = "okay";
+};
+
+&mdss_dp0_out {
+	data-lanes = <0 1 2 3>;
+};
+
+&pcie0 {
+	wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+	perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
+
+	max-link-speed = <2>;
+
+	pinctrl-0 = <&pcie0_default_state>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcie0_phy {
+	vdda-phy-supply = <&vreg_l1e_0p88>;
+	vdda-pll-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&pcie0_port0 {
+	wifi@0 {
+		compatible = "pci17cb,1107";
+		reg = <0x10000 0x0 0x0 0x0 0x0>;
+
+		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+		vddaon-supply = <&vreg_pmu_aon_0p59>;
+		vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+		vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+		vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+		vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+		vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
+		vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
+		vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;
+	};
+};
+
+&pcie1 {
+	wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
+	perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
+
+	pinctrl-0 = <&pcie1_default_state>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcie1_phy {
+	vdda-phy-supply = <&vreg_l3c_0p9>;
+	vdda-pll-supply = <&vreg_l3e_1p2>;
+	vdda-qref-supply = <&vreg_l1e_0p88>;
+
+	status = "okay";
+};
+
+&pcie1_port0 {
+	/* Renesas μPD720201 PCIe USB3.0 HOST CONTROLLER */
+	usb-controller@0 {
+		compatible = "pci1912,0014";
+		reg = <0x10000 0x0 0x0 0x0 0x0>;
+
+		avdd33-supply = <&upd720201_avdd33_reg>;
+		vdd10-supply = <&upd720201_vdd10_reg>;
+		vdd33-supply = <&upd720201_vdd33_reg>;
+
+		pinctrl-0 = <&gamepad_pwr_en>;
+		pinctrl-names = "default";
+	};
+};
+
+&pon_pwrkey {
+	status = "okay";
+};
+
+&pon_resin {
+	linux,code = <KEY_VOLUMEDOWN>;
+
+	status = "okay";
+};
+
+&pm8550_gpios {
+	sdc2_card_det_n: sdc2-card-det-n-state {
+		pins = "gpio12";
+		function = "normal";
+		input-enable;
+		output-disable;
+		bias-pull-up;
+		power-source = <1>;
+	};
+
+	volume_up_n: volume-up-n-state {
+		pins = "gpio6";
+		function = "normal";
+		power-source = <1>;
+		bias-pull-up;
+		input-enable;
+	};
+
+	fan_pwm_active: fan-pwm-active-state {
+		pins = "gpio9";
+		function = "func1";
+		output-low;
+		bias-disable;
+		power-source = <0>;
+		qcom,drive-strength = <3>; /* PMIC_GPIO_STRENGTH_LOW */
+	};
+
+	fan_pwm_sleep: fan-pwm-sleep-state {
+		pins = "gpio9";
+		function = "normal";
+		output-high;
+		bias-disable;
+		power-source = <0>;
+		qcom,drive-strength = <3>; /* PMIC_GPIO_STRENGTH_LOW */
+	};
+};
+
+&pm8550_pwm {
+	status = "okay";
+
+	multi-led {
+		color = <LED_COLOR_ID_RGB>;
+		function = LED_FUNCTION_STATUS;
+		label = "Power Status";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		led@1 {
+			reg = <1>;
+			color = <LED_COLOR_ID_RED>;
+		};
+
+		led@2 {
+			reg = <2>;
+			color = <LED_COLOR_ID_GREEN>;
+		};
+
+		led@3 {
+			reg = <3>;
+			color = <LED_COLOR_ID_BLUE>;
+		};
+	};
+};
+
+&pm8550b_eusb2_repeater {
+	vdd18-supply = <&vreg_l15b_1p8>;
+	vdd3-supply = <&vreg_l5b_3p1>;
+};
+
+&pmk8550_gpios {
+	pmk8550_sleep_clk: sleep-clk-state {
+		pins = "gpio3";
+		function = "func1";
+		input-disable;
+		output-enable;
+		bias-disable;
+		power-source = <0>;
+	};
+};
+
+&pmk8550_rtc {
+	nvmem-cells = <&rtc_offset>;
+	nvmem-cell-names = "offset";
+};
+
+&pmk8550_sdam_2 {
+	rtc_offset: rtc-offset@bc {
+		reg = <0xbc 0x4>;
+	};
+};
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
+&qupv3_id_1 {
+	status = "okay";
+};
+
+&remoteproc_adsp {
+	firmware-name = "qcom/sm8550/ayaneo/adsp.mbn",
+			"qcom/sm8550/ayaneo/adsp_dtb.mbn";
+
+	status = "okay";
+};
+
+&remoteproc_cdsp {
+	/delete-property/ memory-region;
+};
+
+&remoteproc_mpss {
+	/delete-property/ memory-region;
+};
+
+&sdhc_2 {
+	cd-gpios = <&pm8550_gpios 12 GPIO_ACTIVE_LOW>;
+
+	pinctrl-0 = <&sdc2_default &sdc2_card_det_n>;
+	pinctrl-1 = <&sdc2_sleep &sdc2_card_det_n>;
+	pinctrl-names = "default", "sleep";
+
+	vmmc-supply = <&vreg_l9b_2p9>;
+	vqmmc-supply = <&vreg_l8b_1p8>;
+
+	no-sdio;
+	no-mmc;
+
+	sd-uhs-sdr12;
+	sd-uhs-sdr25;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	sd-uhs-ddr50;
+
+	qcom,dll-config = <0x0007442c>;
+
+	status = "okay";
+};
+
+&sleep_clk {
+	clock-frequency = <32764>;
+};
+
+&swr0 {
+	status = "okay";
+
+	spk_amp_l: speaker@0,0 {
+		compatible = "sdw20217020400";
+		reg = <0 0>;
+
+		pinctrl-0 = <&spkr_1_sd_n_active>;
+		pinctrl-names = "default";
+
+		powerdown-gpios = <&tlmm 7 GPIO_ACTIVE_LOW>;
+
+		vdd-1p8-supply = <&vreg_l10b_1p8>;
+		vdd-io-supply = <&vreg_l10b_1p8>;
+
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "SpkrLeft";
+		qcom,port-mapping = <1 2 3 7 10 13>;
+	};
+
+	spk_amp_r: speaker@0,1 {
+		compatible = "sdw20217020400";
+		reg = <0 1>;
+
+		pinctrl-0 = <&spkr_2_sd_n_active>;
+		pinctrl-names = "default";
+
+		powerdown-gpios = <&tlmm 12 GPIO_ACTIVE_LOW>;
+
+		vdd-1p8-supply = <&vreg_l10b_1p8>;
+		vdd-io-supply = <&vreg_l10b_1p8>;
+
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "SpkrRight";
+		qcom,port-mapping = <4 5 6 7 11 13>;
+	};
+};
+
+&thermal_cpu7_top {
+	trips {
+		cpu7_active: cpu7-active {
+			temperature = <50000>;
+			hysteresis = <3000>;
+			type = "active";
+		};
+	};
+
+	cooling-maps {
+		map {
+			trip = <&cpu7_active>;
+			cooling-device = <&pwm_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+		};
+	};
+};
+
+&thermal_cpuss0 {
+	trips {
+		cpuss0_active: cpuss0-active {
+			temperature = <50000>;
+			hysteresis = <3000>;
+			type = "active";
+		};
+	};
+
+	cooling-maps {
+		map {
+			trip = <&cpuss0_active>;
+			cooling-device = <&pwm_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+		};
+	};
+};
+
+&thermal_cpuss1 {
+	trips {
+		cpuss1_active: cpuss1-active {
+			temperature = <50000>;
+			hysteresis = <3000>;
+			type = "active";
+		};
+	};
+
+	cooling-maps {
+		map {
+			trip = <&cpuss1_active>;
+			cooling-device = <&pwm_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+		};
+	};
+};
+
+&thermal_cpuss2 {
+	trips {
+		cpuss2_active: cpuss2-active {
+			temperature = <50000>;
+			hysteresis = <3000>;
+			type = "active";
+		};
+	};
+
+	cooling-maps {
+		map {
+			trip = <&cpuss2_active>;
+			cooling-device = <&pwm_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+		};
+	};
+};
+
+&thermal_cpuss3 {
+	trips {
+		cpuss3_active: cpuss3-active {
+			temperature = <50000>;
+			hysteresis = <3000>;
+			type = "active";
+		};
+	};
+
+	cooling-maps {
+		map {
+			trip = <&cpuss3_active>;
+			cooling-device = <&pwm_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+		};
+	};
+};
+
+&thermal_gpuss0 {
+	trips {
+		gpuss0_active: gpuss0-active {
+			temperature = <55000>;
+			hysteresis = <3000>;
+			type = "active";
+		};
+	};
+
+	cooling-maps {
+		map {
+			trip = <&gpuss0_active>;
+			cooling-device = <&pwm_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+		};
+	};
+};
+
+&thermal_gpuss1 {
+	trips {
+		gpuss1_active: gpuss1-active {
+			temperature = <55000>;
+			hysteresis = <3000>;
+			type = "active";
+		};
+	};
+
+	cooling-maps {
+		map {
+			trip = <&gpuss1_active>;
+			cooling-device = <&pwm_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+		};
+	};
+};
+
+&thermal_gpuss2 {
+	trips {
+		gpuss2_active: gpuss2-active {
+			temperature = <55000>;
+			hysteresis = <3000>;
+			type = "active";
+		};
+	};
+
+	cooling-maps {
+		map {
+			trip = <&gpuss2_active>;
+			cooling-device = <&pwm_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+		};
+	};
+};
+
+&thermal_gpuss3 {
+	trips {
+		gpuss3_active: gpuss3-active {
+			temperature = <55000>;
+			hysteresis = <3000>;
+			type = "active";
+		};
+	};
+
+	cooling-maps {
+		map {
+			trip = <&gpuss3_active>;
+			cooling-device = <&pwm_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+		};
+	};
+};
+
+&thermal_gpuss4 {
+	trips {
+		gpuss4_active: gpuss4-active {
+			temperature = <55000>;
+			hysteresis = <3000>;
+			type = "active";
+		};
+	};
+
+	cooling-maps {
+		map {
+			trip = <&gpuss4_active>;
+			cooling-device = <&pwm_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+		};
+	};
+};
+
+&thermal_gpuss5 {
+	trips {
+		gpuss5_active: gpuss5-active {
+			temperature = <55000>;
+			hysteresis = <3000>;
+			type = "active";
+		};
+	};
+
+	cooling-maps {
+		map {
+			trip = <&gpuss5_active>;
+			cooling-device = <&pwm_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+		};
+	};
+};
+
+&thermal_gpuss6 {
+	trips {
+		gpuss6_active: gpuss6-active {
+			temperature = <55000>;
+			hysteresis = <3000>;
+			type = "active";
+		};
+	};
+
+	cooling-maps {
+		map {
+			trip = <&gpuss6_active>;
+			cooling-device = <&pwm_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+		};
+	};
+};
+
+&thermal_gpuss7 {
+	trips {
+		gpuss7_active: gpuss7-active {
+			temperature = <55000>;
+			hysteresis = <3000>;
+			type = "active";
+		};
+	};
+
+	cooling-maps {
+		map {
+			trip = <&gpuss7_active>;
+			cooling-device = <&pwm_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+		};
+	};
+};
+
+&tlmm {
+	gpio-reserved-ranges = <32 4>;
+
+	bt_default: bt-default-state {
+		bt-en-pins {
+			pins = "gpio81";
+			function = "gpio";
+			drive-strength = <16>;
+			bias-disable;
+		};
+
+		sw-ctrl-pins {
+			pins = "gpio82";
+			function = "gpio";
+			bias-pull-down;
+		};
+	};
+
+	fan_pwr_active: fan-pwr-active-state {
+		pins = "gpio31";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	fan_int: fan-int-state {
+		pins = "gpio64";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+
+	upd720201_avdd33: upd720201-avdd33-state {
+		pins = "gpio10";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	upd720201_vdd10: upd720201-vdd10-state {
+		pins = "gpio13";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	upd720201_vdd33: upd720201-vdd33-state {
+		pins = "gpio18";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	gamepad_pwr_en: gamepad-pwr-en-active-state {
+		pins = "gpio52";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-high;
+	};
+
+	wlan_en: wlan-en-state {
+		pins = "gpio80";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-pull-down;
+	};
+
+	spkr_1_sd_n_active: spkr-1-sd-n-active-state {
+		pins = "gpio7";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	spkr_2_sd_n_active: spkr-2-sd-n-active-state {
+		pins = "gpio12";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	ts_rst_default: ts-rst-default-state {
+		pins = "gpio24";
+		function = "gpio";
+		bias-pull-up;
+		drive-strength = <8>;
+	};
+
+	ts_rst_sleep: ts-rst-sleep-state {
+		pins = "gpio24";
+		function = "gpio";
+		bias-pull-down;
+		drive-strength = <2>;
+	};
+
+	ts_int_default: ts-int-default-state {
+		pins = "gpio25";
+		function = "gpio";
+		bias-pull-up;
+		drive-strength = <8>;
+	};
+
+	ts_int_sleep: ts-int-sleep-state {
+		pins = "gpio25";
+		function = "gpio";
+		bias-pull-down;
+		drive-strength = <2>;
+	};
+
+	ts2_irq: ts2-irq-state {
+		pins = "gpio39";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	ts2_reset: ts2-reset-state {
+		pins = "gpio38";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-pull-down;
+	};
+};
+
+&uart7 {
+	status = "okay";
+};
+
+/* AYANEO Controller serial interface */
+&uart11 {
+	status = "okay";
+};
+
+&uart14 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn7850-bt";
+
+		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+		vddaon-supply = <&vreg_pmu_aon_0p59>;
+		vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+		vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+		vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+		vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+		vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
+
+		max-speed = <3200000>;
+	};
+};
+
+&ufs_mem_hc {
+	reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;
+
+	vcc-supply = <&vreg_l17b_2p5>;
+	vcc-max-microamp = <1300000>;
+	vccq-supply = <&vreg_l1g_1p2>;
+	vccq-max-microamp = <1200000>;
+	vdd-hba-supply = <&vreg_l3g_1p2>;
+
+	status = "okay";
+};
+
+&ufs_mem_phy {
+	vdda-phy-supply = <&vreg_l1d_0p88>;
+	vdda-pll-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3_hs {
+	remote-endpoint = <&pmic_glink_hs_in>;
+};
+
+&usb_1_hsphy {
+	vdd-supply = <&vreg_l1e_0p88>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	phys = <&pm8550b_eusb2_repeater>;
+
+	status = "okay";
+};
+
+&usb_dp_qmpphy {
+	vdda-phy-supply = <&vreg_l3e_1p2>;
+	vdda-pll-supply = <&vreg_l3f_0p88>;
+
+	status = "okay";
+};
+
+&usb_dp_qmpphy_out {
+	remote-endpoint = <&redriver_ss_in>;
+};
+
+&xo_board {
+	clock-frequency = <76800000>;
+};
diff --git a/arch/arm64/boot/dts/qcom/sm8550.dtsi b/arch/arm64/boot/dts/qcom/sm8550.dtsi
index fcbcf22ff951..7ce4cfc5b146 100644
--- a/arch/arm64/boot/dts/qcom/sm8550.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8550.dtsi
@@ -6180,7 +6180,7 @@ reset-mon-config {
 			};
 		};
 
-		cpuss0-thermal {
+		thermal_cpuss0: cpuss0-thermal {
 			thermal-sensors = <&tsens0 1>;
 
 			trips {
@@ -6198,7 +6198,7 @@ reset-mon-config {
 			};
 		};
 
-		cpuss1-thermal {
+		thermal_cpuss1: cpuss1-thermal {
 			thermal-sensors = <&tsens0 2>;
 
 			trips {
@@ -6216,7 +6216,7 @@ reset-mon-config {
 			};
 		};
 
-		cpuss2-thermal {
+		thermal_cpuss2: cpuss2-thermal {
 			thermal-sensors = <&tsens0 3>;
 
 			trips {
@@ -6234,7 +6234,7 @@ reset-mon-config {
 			};
 		};
 
-		cpuss3-thermal {
+		thermal_cpuss3: cpuss3-thermal {
 			thermal-sensors = <&tsens0 4>;
 
 			trips {
@@ -6444,7 +6444,7 @@ cpu6_bottom_crit: cpu-critical {
 			};
 		};
 
-		cpu7-top-thermal {
+		thermal_cpu7_top: cpu7-top-thermal {
 			thermal-sensors = <&tsens0 13>;
 
 			trips {
@@ -6952,7 +6952,7 @@ reset-mon-config {
 			};
 		};
 
-		gpuss-0-thermal {
+		thermal_gpuss0: gpuss-0-thermal {
 			polling-delay-passive = <10>;
 
 			thermal-sensors = <&tsens2 1>;
@@ -6985,7 +6985,7 @@ trip-point2 {
 			};
 		};
 
-		gpuss-1-thermal {
+		thermal_gpuss1: gpuss-1-thermal {
 			polling-delay-passive = <10>;
 
 			thermal-sensors = <&tsens2 2>;
@@ -7018,7 +7018,7 @@ trip-point2 {
 			};
 		};
 
-		gpuss-2-thermal {
+		thermal_gpuss2: gpuss-2-thermal {
 			polling-delay-passive = <10>;
 
 			thermal-sensors = <&tsens2 3>;
@@ -7051,7 +7051,7 @@ trip-point2 {
 			};
 		};
 
-		gpuss-3-thermal {
+		thermal_gpuss3: gpuss-3-thermal {
 			polling-delay-passive = <10>;
 
 			thermal-sensors = <&tsens2 4>;
@@ -7084,7 +7084,7 @@ trip-point2 {
 			};
 		};
 
-		gpuss-4-thermal {
+		thermal_gpuss4: gpuss-4-thermal {
 			polling-delay-passive = <10>;
 
 			thermal-sensors = <&tsens2 5>;
@@ -7117,7 +7117,7 @@ trip-point2 {
 			};
 		};
 
-		gpuss-5-thermal {
+		thermal_gpuss5: gpuss-5-thermal {
 			polling-delay-passive = <10>;
 
 			thermal-sensors = <&tsens2 6>;
@@ -7150,7 +7150,7 @@ trip-point2 {
 			};
 		};
 
-		gpuss-6-thermal {
+		thermal_gpuss6: gpuss-6-thermal {
 			polling-delay-passive = <10>;
 
 			thermal-sensors = <&tsens2 7>;
@@ -7183,7 +7183,7 @@ trip-point2 {
 			};
 		};
 
-		gpuss-7-thermal {
+		thermal_gpuss7: gpuss-7-thermal {
 			polling-delay-passive = <10>;
 
 			thermal-sensors = <&tsens2 8>;

-- 
2.55.0

[PATCH v6 4/4] arm64: dts: qcom: qcs8550-ayaneo-pocket-ds: add the lower DSI panel

[Alexandre Hamamdjian via B4 Relay]

From: Alexandre Hamamdjian <azkali.limited@gmail.com>

The Pocket DS drives two panels. The lower one is a 768x1024 IPS LCD on
a Sitronix ST7703 DDIC hanging off mdss_dsi1, and all of the pieces it
needs have now landed: the ayaneo,pocket-ds-lower-panel compatible in
the ST7703 binding, the SGMicro SGM3804 dual-rail charge pump driver and
the Silergy SY7758 backlight driver.

The SGM3804 on i2c0 supplies the panel bias. Its two rails are enabled
by separate GPIOs and both are programmed to 5.2 V; that figure is the
vendor register configuration (0x00 = 0x0c, 0x01 = 0x0c), which lands on
5.2 V in the driver's 4.0 V + 100 mV linear range. tlmm 152 enables the
positive rail and tlmm 153 the negative one. Only the positive rail has
a consumer, because the ST7703 binding models a single vcc-supply, so
the negative rail is marked regulator-always-on to keep AVEE up while
the panel is on; a better modelling of the pair is welcome.

The SY7758 backlight sits on the same bus. Its enable line was
determined on the device: driving tlmm 42 low makes the chip stop
acknowledging on i2c while the TCA6408 on the same segment keeps
responding, so tlmm 42 gates the SY7758 alone rather than the bus.

The TCA6408 expander supplies the rest: line 0 gates the panel IOVCC
rail, modelled as a fixed regulator, and line 2 is the panel reset.

sde_dsi1_active keeps its output-high because tlmm 137 has no GPIO
consumer anywhere in the tree; pinctrl is the only thing asserting it.

The upper panel is not added here. Its Chipone ICNA3512 binding makes
disp-supply and blvdd-supply mandatory, and this board has no separately
controllable rail for either; the vendor device tree drives the upper
panel purely through a platform enable GPIO and points the panel node at
the simulator supply list. It will follow once that wiring is confirmed.

Signed-off-by: Alexandre Hamamdjian <azkali.limited@gmail.com>
---
 .../boot/dts/qcom/qcs8550-ayaneo-pocket-ds.dts     | 97 ++++++++++++++++++++++
 1 file changed, 97 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/qcs8550-ayaneo-pocket-ds.dts b/arch/arm64/boot/dts/qcom/qcs8550-ayaneo-pocket-ds.dts
index 09b1c86cc3d3..72c81667c085 100644
--- a/arch/arm64/boot/dts/qcom/qcs8550-ayaneo-pocket-ds.dts
+++ b/arch/arm64/boot/dts/qcom/qcs8550-ayaneo-pocket-ds.dts
@@ -314,6 +314,17 @@ upd720201_vdd33_reg: upd720201-vdd33-regulator {
 		pinctrl-names = "default";
 	};
 
+	vreg_panel1_iovcc: panel1-iovcc-regulator {
+		compatible = "regulator-fixed";
+
+		regulator-name = "panel1_iovcc";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		gpios = <&tca6408 0 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
 	vdd_fan_5v0: vdd-fan-5v0-regulator {
 		compatible = "regulator-fixed";
 
@@ -829,6 +840,38 @@ tca6408: gpio@20 {
 
 		vcc-supply = <&tca6424_vcc>;
 	};
+
+	backlight: backlight@2e {
+		compatible = "silergy,sy7758";
+		reg = <0x2e>;
+
+		enable-gpios = <&tlmm 42 GPIO_ACTIVE_HIGH>;
+	};
+
+	sgm3804: regulator@3e {
+		compatible = "sgmicro,sgm3804";
+		reg = <0x3e>;
+
+		vin-supply = <&vph_pwr>;
+
+		sgm3804_pos: pos {
+			regulator-name = "panel1_avdd";
+			regulator-min-microvolt = <5200000>;
+			regulator-max-microvolt = <5200000>;
+
+			enable-gpios = <&tlmm 152 GPIO_ACTIVE_HIGH>;
+		};
+
+		sgm3804_neg: neg {
+			regulator-name = "panel1_avee";
+			regulator-min-microvolt = <5200000>;
+			regulator-max-microvolt = <5200000>;
+
+			enable-gpios = <&tlmm 153 GPIO_ACTIVE_HIGH>;
+
+			regulator-always-on;
+		};
+	};
 };
 
 &i2c2 {
@@ -960,6 +1003,45 @@ &mdss_dp0_out {
 	data-lanes = <0 1 2 3>;
 };
 
+&mdss_dsi1 {
+	vdda-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+
+	panel@0 {
+		compatible = "ayaneo,pocket-ds-lower-panel";
+		reg = <0>;
+
+		vcc-supply = <&sgm3804_pos>;
+		iovcc-supply = <&vreg_panel1_iovcc>;
+
+		reset-gpios = <&tca6408 2 GPIO_ACTIVE_LOW>;
+		backlight = <&backlight>;
+		rotation = <270>;
+
+		pinctrl-0 = <&sde_dsi1_active>;
+		pinctrl-1 = <&sde_dsi1_suspend>;
+		pinctrl-names = "default", "sleep";
+
+		port {
+			panel1_in: endpoint {
+				remote-endpoint = <&mdss_dsi1_out>;
+			};
+		};
+	};
+};
+
+&mdss_dsi1_out {
+	remote-endpoint = <&panel1_in>;
+	data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi1_phy {
+	vdds-supply = <&vreg_l1e_0p88>;
+
+	status = "okay";
+};
+
 &pcie0 {
 	wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
 	perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
@@ -1558,6 +1640,21 @@ ts2_irq: ts2-irq-state {
 		bias-disable;
 	};
 
+	sde_dsi1_active: sde-dsi1-active-state {
+		pins = "gpio137";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+		output-high;
+	};
+
+	sde_dsi1_suspend: sde-dsi1-suspend-state {
+		pins = "gpio137";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
 	ts2_reset: ts2-reset-state {
 		pins = "gpio38";
 		function = "gpio";

-- 
2.55.0

Re: [PATCH v6 2/4] arm64: dts: qcom: sm8550: add UART11 node

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider:

Pre-existing issues:
- [High] The SPI nodes `spi11` and `spi12` in `sm8550.dtsi` incorrectly configure their GPI DMA channels to use the I2C protocol (`QCOM_GPI_I2C`) instead of the SPI protocol (`QCOM_GPI_SPI`).
--

--- Patch [2]: [PATCH v6 2/4] arm64: dts: qcom: sm8550: add UART11 node ---
commit 367c60765aa391aa9b6b3277a433dd844de194db
Author: Alexandre Hamamdjian <azkali.limited@gmail.com>

arm64: dts: qcom: sm8550: add UART11 node

This commit adds the UART11 controller node and its default pinctrl state
to sm8550.dtsi. It reuses the 120MHz OPP table already utilized by the
i2c11 and spi11 nodes.

> diff --git a/arch/arm64/boot/dts/qcom/sm8550.dtsi b/arch/arm64/boot/dts/qcom/sm8550.dtsi
> --- a/arch/arm64/boot/dts/qcom/sm8550.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8550.dtsi
> @@ -1442,6 +1442,24 @@ &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ACTIVE_ONLY>,
>  				status = "disabled";
>  			};
>  
> +			uart11: serial@88c000 {

[Severity: High]
This is a pre-existing issue, but while reviewing the new uart11 node and
its surrounding context, I noticed that the existing spi11 and spi12 nodes
appear to incorrectly configure their GPI DMA channels to use the I2C
protocol:

spi11 {
        ...
        dmas = <&gpi_dma2 0 3 QCOM_GPI_I2C>,
               <&gpi_dma2 1 3 QCOM_GPI_I2C>;
}

spi12 {
        ...
        dmas = <&gpi_dma2 0 4 QCOM_GPI_I2C>,
               <&gpi_dma2 1 4 QCOM_GPI_I2C>;
}

Does configuring the SPI controller's DMA engine with QCOM_GPI_I2C instead
of QCOM_GPI_SPI cause the hardware to expect I2C command sequences,
breaking SPI DMA functionality for any peripherals attached to these ports?

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20260824-pocketds-v6-0-370161574ca2@gmail.com?part=2

Re: [PATCH v6 4/4] arm64: dts: qcom: qcs8550-ayaneo-pocket-ds: add the lower DSI panel

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 3 potential issue(s) to consider:
- [High] The negative display bias rail (AVEE) is forced always-on, which causes continuous power drain and violates LCD power sequencing constraints.
- [Medium] Misuse of pinctrl 'output-high' to statically drive a panel/DSI enable GPIO, breaking runtime power management.
- [Medium] The sde_dsi1_suspend pinctrl state fails to disable the output high configuration, causing active power leakage during system suspend.
--

--- Patch [4]: [PATCH v6 4/4] arm64: dts: qcom: qcs8550-ayaneo-pocket-ds: add the lower DSI panel ---
commit 7b158fa2393a8ff0b401b5e960f82b14b4778a83
Author: Alexandre Hamamdjian <azkali.limited@gmail.com>

arm64: dts: qcom: qcs8550-ayaneo-pocket-ds: add the lower DSI panel

This commit adds support for the lower 768x1024 IPS LCD panel on the 
Pocket DS device. It configures the ST7703 panel along with its required 
SGM3804 bias supply, SY7758 backlight driver, and TCA6408 GPIO expander.

> diff --git a/arch/arm64/boot/dts/qcom/qcs8550-ayaneo-pocket-ds.dts b/arch/arm64/boot/dts/qcom/qcs8550-ayaneo-pocket-ds.dts
> --- a/arch/arm64/boot/dts/qcom/qcs8550-ayaneo-pocket-ds.dts
> +++ b/arch/arm64/boot/dts/qcom/qcs8550-ayaneo-pocket-ds.dts
[ ... ]
> @@ -829,6 +840,38 @@ tca6408: gpio@20 {
[ ... ]
> +		sgm3804_neg: neg {
> +			regulator-name = "panel1_avee";
> +			regulator-min-microvolt = <5200000>;
> +			regulator-max-microvolt = <5200000>;
> +
> +			enable-gpios = <&tlmm 153 GPIO_ACTIVE_HIGH>;
> +
> +			regulator-always-on;

[Severity: High]
Does forcing this negative display bias rail (AVEE) to be always-on risk
permanent hardware damage?

Applying a continuous negative bias (-5.2V) to the LCD panel while the
positive and logic supplies (AVDD, IOVCC) are disabled during display
blanking or system suspend often violates the absolute maximum ratings
of LCD drivers. Over time, this could cause latch-up and hardware failure,
along with a continuous quiescent battery drain on the device.

Could this negative rail be modeled differently so it is toggled
synchronously with the panel's active/sleep lifecycle?

> +		};
> +	};
>  };
[ ... ]
> @@ -960,6 +1003,45 @@ &mdss_dp0_out {
>  	data-lanes = <0 1 2 3>;
>  };
>  
> +&mdss_dsi1 {
[ ... ]
> +	panel@0 {
> +		compatible = "ayaneo,pocket-ds-lower-panel";
> +		reg = <0>;
> +
> +		vcc-supply = <&sgm3804_pos>;
> +		iovcc-supply = <&vreg_panel1_iovcc>;
> +
> +		reset-gpios = <&tca6408 2 GPIO_ACTIVE_LOW>;
> +		backlight = <&backlight>;
> +		rotation = <270>;
> +
> +		pinctrl-0 = <&sde_dsi1_active>;
> +		pinctrl-1 = <&sde_dsi1_suspend>;
> +		pinctrl-names = "default", "sleep";

[Severity: Medium]
Will using the pinctrl output-high property (defined in sde_dsi1_active) 
to statically drive the panel enable GPIO (tlmm 137) break runtime power 
management?

Because DRM panels typically do not automatically transition to sleep
pinctrl states during runtime display blanking (for example, in
drm_panel_unprepare), the pin will remain asserted when the screen is
logically turned off.

If this pin controls the panel or a related signal, should it be modeled
as an explicit enable-gpios or fixed regulator instead so it toggles
correctly with the panel lifecycle?

> +
> +		port {
> +			panel1_in: endpoint {
> +				remote-endpoint = <&mdss_dsi1_out>;
> +			};
> +		};
> +	};
> +};
[ ... ]
> @@ -1558,6 +1640,21 @@ ts2_irq: ts2-irq-state {
>  		bias-disable;
>  	};
>  
> +	sde_dsi1_active: sde-dsi1-active-state {
> +		pins = "gpio137";
> +		function = "gpio";
> +		drive-strength = <8>;
> +		bias-disable;
> +		output-high;
> +	};
> +
> +	sde_dsi1_suspend: sde-dsi1-suspend-state {
> +		pins = "gpio137";
> +		function = "gpio";
> +		drive-strength = <2>;
> +		bias-pull-down;

[Severity: Medium]
Does this suspend state cause an active power leakage during system suspend?

The active state configures the pin with output-high, but this suspend
state only defines bias-pull-down without an explicit output-low or
output-disable. 

When transitioning to suspend, the pin will remain actively driven high
while the internal pull-down resistor is concurrently enabled, which
creates a direct short-to-ground leakage path.

> +	};
> +
>  	ts2_reset: ts2-reset-state {
>  		pins = "gpio38";
>  		function = "gpio";

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20260824-pocketds-v6-0-370161574ca2@gmail.com?part=4

Re: [PATCH v6 3/4] arm64: dts: qcom: add basic devicetree for Ayaneo Pocket DS gaming console

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 2 potential issue(s) to consider:
- [Medium] The PWM fan control pin is actively driven HIGH during system suspend while the fan's power supply is disabled, causing leakage current and potentially running the fan at 100% duty cycle if back-powered.
- [Low] PCIe child nodes have unit addresses that do not match the first address cell of their 'reg' property.
--

--- Patch [3]: [PATCH v6 3/4] arm64: dts: qcom: add basic devicetree for Ayaneo Pocket DS gaming console ---
commit 44774ff01d05ab46cbf94f40052649086f920bb4
Author: Teguh Sobirin <teguh@sobir.in>

arm64: dts: qcom: add basic devicetree for Ayaneo Pocket DS gaming console

Adds initial Device Tree for the Ayaneo Pocket DS gaming console based
on the QCS8550 platform, wiring up core peripherals, USB-C/DP, microSD, 
WiFi/BT, and gaming controls.

> diff --git a/arch/arm64/boot/dts/qcom/qcs8550-ayaneo-pocket-ds.dts b/arch/arm64/boot/dts/qcom/qcs8550-ayaneo-pocket-ds.dts
> new file mode 100644
> index 0000000000000..09b1c86cc3d35
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/qcs8550-ayaneo-pocket-ds.dts

[ ... ]

> +	vdd_fan_5v0: vdd-fan-5v0-regulator {
> +		compatible = "regulator-fixed";
> +
> +		regulator-name = "vdd_fan_5v0";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +
> +		gpios = <&tlmm 31 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +
> +		pinctrl-0 = <&fan_pwr_active>;
> +		pinctrl-names = "default";
> +
> +		regulator-state-mem {
> +			regulator-off-in-suspend;
> +		};
> +	};

[ ... ]

> +&pm8550_gpios {

[ ... ]

> +	fan_pwm_sleep: fan-pwm-sleep-state {
> +		pins = "gpio9";
> +		function = "normal";
> +		output-high;

[Severity: Medium]
Does driving this pin high during suspend create a leakage path? Since
vdd_fan_5v0 is configured with regulator-off-in-suspend, actively driving
the control pin into an unpowered fan controller might cause back-powering.

> +		bias-disable;
> +		power-source = <0>;
> +		qcom,drive-strength = <3>; /* PMIC_GPIO_STRENGTH_LOW */
> +	};

[ ... ]

> +&pcie0_port0 {
> +	wifi@0 {
> +		compatible = "pci17cb,1107";
> +		reg = <0x10000 0x0 0x0 0x0 0x0>;

[Severity: Low]
Should the node name match the unit address in the reg property? It looks
like this should be wifi@10000 to avoid dtc validation warnings.

> +
> +		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
> +		vddaon-supply = <&vreg_pmu_aon_0p59>;

[ ... ]

> +&pcie1_port0 {
> +	/* Renesas μPD720201 PCIe USB3.0 HOST CONTROLLER */
> +	usb-controller@0 {
> +		compatible = "pci1912,0014";
> +		reg = <0x10000 0x0 0x0 0x0 0x0>;

[Severity: Low]
Should this node also be named usb-controller@10000 to match the first
address cell in the reg property?

> +
> +		avdd33-supply = <&upd720201_avdd33_reg>;
> +		vdd10-supply = <&upd720201_vdd10_reg>;

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20260824-pocketds-v6-0-370161574ca2@gmail.com?part=3