[PATCH 3/6] arm64: dts: qcom: sm8250-hdk: Add FSA4480 USB-C protocol chip

[ShiTou Hong <redstone.dcity@gmail.com>]

The sm8250-hdk has a USB-C port supporting OTG and DP altmode.
This is implemented with the FSA4480 chip,
which hasn't been added in the dts file.

Change the USB controller mode to OTG.
Enable the i2c controller for the chip and the dp controller.
Configure the PM8150b type-c module and vbus regulator.

Co-developed-by: KancyJoe <kancy2333@outlook.com>
Signed-off-by: ShiTou Hong <dc_redstone@outlook.com>
---
 arch/arm64/boot/dts/qcom/sm8250-hdk.dts | 113 +++++++++++++++++++++++-
 1 file changed, 112 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8250-hdk.dts b/arch/arm64/boot/dts/qcom/sm8250-hdk.dts
index 0bc946682..7a2903941 100644
--- a/arch/arm64/boot/dts/qcom/sm8250-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8250-hdk.dts
@@ -6,6 +6,7 @@
 /dts-v1/;
 
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include <dt-bindings/usb/pd.h>
 #include "sm8250.dtsi"
 #include "pm8150.dtsi"
 #include "pm8150b.dtsi"
@@ -415,6 +416,10 @@ &pon_resin {
 	linux,code = <KEY_VOLUMEDOWN>;
 };
 
+&qupv3_id_2 {
+	status = "okay";
+};
+
 &qupv3_id_1 {
 	status = "okay";
 };
@@ -509,6 +514,10 @@ &usb_1_qmpphy {
 	vdda-pll-supply = <&vreg_l9a_1p2>;
 };
 
+&usb_1_qmpphy_out {
+	remote-endpoint = <&pm8150b_typec_mux_in>;
+};
+
 &usb_2_qmpphy {
 	status = "okay";
 	vdda-phy-supply = <&vreg_l18a_0p92>;
@@ -524,13 +533,18 @@ &usb_2 {
 };
 
 &usb_1_dwc3 {
-	dr_mode = "peripheral";
+	dr_mode = "otg";
+	usb-role-switch;
 };
 
 &usb_2_dwc3 {
 	dr_mode = "host";
 };
 
+&usb_1_dwc3_hs_out {
+	remote-endpoint = <&pm8150b_hs_in>;
+};
+
 &venus {
 	status = "okay";
 };
@@ -589,6 +603,28 @@ lt9611_out: endpoint {
 	};
 };
 
+&i2c15 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	fsa4480@43 {
+		compatible = "fcs,fsa4480";
+		reg = <0x43>;
+
+		interrupts-extended = <&tlmm 63 IRQ_TYPE_LEVEL_LOW>;
+
+		vcc-supply = <&vreg_bob>;
+		mode-switch;
+		orientation-switch;
+
+		port {
+			fsa4480_sbu_mux: endpoint {
+				remote-endpoint = <&pm8150b_typec_sbu_out>;
+			};
+		};
+	};
+};
+
 &gpi_dma0 {
 	status = "okay";
 };
@@ -597,6 +633,15 @@ &mdss {
 	status = "okay";
 };
 
+&mdss_dp {
+	status = "okay";
+};
+
+&mdss_dp_out {
+	data-lanes = <0 1>;
+	remote-endpoint = <&usb_1_qmpphy_dp_in>;
+};
+
 &mdss_dsi0 {
 	status = "okay";
 	vdda-supply = <&vreg_l9a_1p2>;
@@ -611,3 +656,69 @@ &mdss_dsi0_phy {
 	status = "okay";
 	vdds-supply = <&vreg_l5a_0p88>;
 };
+
+&pm8150b_vbus {
+	regulator-min-microamp = <500000>;
+	regulator-max-microamp = <3000000>;
+	status = "okay";
+};
+
+&pm8150b_typec {
+	status = "okay";
+
+	vdd-pdphy-supply = <&vreg_l2a_3p1>;
+
+	connector {
+		compatible = "usb-c-connector";
+
+		power-role = "source";
+		data-role = "dual";
+		self-powered;
+
+		vbus-supply = <&pm8150b_vbus>;
+
+		source-pdos = <PDO_FIXED(5000, 3000,PDO_FIXED_DUAL_ROLE |
+					 PDO_FIXED_USB_COMM |
+					 PDO_FIXED_DATA_SWAP)>;
+
+		altmodes {
+			displayport {
+				svid = /bits/ 16 <0xff01>;
+				vdo = <0x00001c46>;
+			};
+		};
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				pm8150b_hs_in: endpoint {
+					remote-endpoint = <&usb_1_dwc3_hs_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				pm8150b_typec_mux_in: endpoint {
+					remote-endpoint = <&usb_1_qmpphy_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				pm8150b_typec_sbu_out: endpoint {
+					remote-endpoint = <&fsa4480_sbu_mux>;
+				};
+			};
+		};
+	};
+};
+
+&usb_1_qmpphy_dp_in {
+	remote-endpoint = <&mdss_dp_out>;
+};
-- 
2.47.3