[PATCH 2/6] arm64: dts: qcom: sm8250-hdk: Add LT9611UXC HDMI bridge

[ShiTou Hong <redstone.dcity@gmail.com>]

The sm8250-hdk has a video bridge chip LT9611UXC
converting MIPI DSI to HDMI, which hasn't been added
in the dts, so we have no HDMI signal.

Add the 1V2 supply node for the chip and the HDMI connector node.
Enable the i2c port of the chip, the display controller and DSI port.
Add the pinctrl of LT9611UXC's RST and IRQ pins.

Co-developed-by: KancyJoe <kancy2333@outlook.com>
Signed-off-by: ShiTou Hong <dc_redstone@outlook.com>
---
 arch/arm64/boot/dts/qcom/sm8250-hdk.dts | 105 ++++++++++++++++++++++++
 1 file changed, 105 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8250-hdk.dts b/arch/arm64/boot/dts/qcom/sm8250-hdk.dts
index a049d78f5..0bc946682 100644
--- a/arch/arm64/boot/dts/qcom/sm8250-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8250-hdk.dts
@@ -44,6 +44,18 @@ vreg_s4a_1p8: pm8150-s4 {
 		vin-supply = <&vph_pwr>;
 	};
 
+	lt9611_1v2: lt9611-vdd12-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "LT9611_1V2";
+
+		regulator-always-on;
+		regulator-boot-on;
+
+		vin-supply = <&vph_pwr>;
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+	};
+
 	vreg_s6c_0p88: smpc6-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "vreg_s6c_0p88";
@@ -63,6 +75,17 @@ key-vol-up {
 			gpios = <&pm8150_gpios 6 GPIO_ACTIVE_LOW>;
 		};
 	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con: endpoint {
+				remote-endpoint = <&lt9611_out>;
+			};
+		};
+	};
 };
 
 &apps_rsc {
@@ -396,6 +419,10 @@ &qupv3_id_1 {
 	status = "okay";
 };
 
+&qupv3_id_0 {
+	status = "okay";
+};
+
 &tlmm {
 	gpio-reserved-ranges = <28 4>, <40 4>;
 
@@ -424,6 +451,20 @@ clk-pins {
 			drive-strength = <16>;
 		};
 	};
+
+	lt9611_pins: lt9611-default-state {
+		irq-pins {
+			pins = "gpio1";
+			function = "gpio";
+			bias-disable;
+		};
+
+		rst-pins {
+			pins = "gpio2";
+			function = "gpio";
+			output-high;
+		};
+	};
 };
 
 &uart12 {
@@ -506,3 +547,67 @@ &sdhc_2 {
 	pinctrl-0 = <&sdc2_default>, <&sd_ufs_cd_pins>;
 	pinctrl-1 = <&sdc2_sleep_state>, <&sd_ufs_cd_pins>;
 };
+
+&i2c1 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	lt9611_codec: hdmi-bridge@2b {
+		compatible = "lontium,lt9611uxc";
+		reg = <0x2b>;
+		#sound-dai-cells = <1>;
+
+		interrupts-extended = <&tlmm 1 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
+
+		vdd-supply = <&lt9611_1v2>;
+		vcc-supply = <&vreg_bob>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&lt9611_pins>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				lt9611_a: endpoint {
+					remote-endpoint = <&mdss_dsi0_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				lt9611_out: endpoint {
+					remote-endpoint = <&hdmi_con>;
+				};
+			};
+		};
+	};
+};
+
+&gpi_dma0 {
+	status = "okay";
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_dsi0 {
+	status = "okay";
+	vdda-supply = <&vreg_l9a_1p2>;
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&lt9611_a>;
+	data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi0_phy {
+	status = "okay";
+	vdds-supply = <&vreg_l5a_0p88>;
+};
-- 
2.47.3