From: Svyatoslav Ryhel <clamor95@gmail.com>
To: Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
Thierry Reding <thierry.reding@kernel.org>,
Jonathan Hunter <jonathanh@nvidia.com>,
Svyatoslav Ryhel <clamor95@gmail.com>,
Mikko Perttunen <mperttunen@nvidia.com>
Cc: devicetree@vger.kernel.org, linux-tegra@vger.kernel.org,
linux-kernel@vger.kernel.org
Subject: [PATCH v1 06/18] ARM: tegra: tegratab: Configure USB and power supply
Date: Sun, 22 Nov 2026 22:13:55 +0200 [thread overview]
Message-ID: <20261122201407.23742-7-clamor95@gmail.com> (raw)
In-Reply-To: <20261122201407.23742-1-clamor95@gmail.com>
Previously, USB was partially broken on the Tegra Note 7, as it supports
OTG and requires proper configuration of both the power supply and the
USB controller/PHY.
Configure the power supply by adding and linking the battery cell,
charger, and fuel gauge nodes. Configure the USB controller for OTG
support using the Palmas extcon for ID pin detection and the charger for
VBUS, and add the usb-connector node.
The device now works in both peripheral and host modes as expected.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
---
.../tegra114-nvidia-tegratab-common.dtsi | 98 ++++++++++++++++++-
1 file changed, 94 insertions(+), 4 deletions(-)
diff --git a/arch/arm/boot/dts/nvidia/tegra114-nvidia-tegratab-common.dtsi b/arch/arm/boot/dts/nvidia/tegra114-nvidia-tegratab-common.dtsi
index 26f1f7dbcc4c7..2ccee3b70aac9 100644
--- a/arch/arm/boot/dts/nvidia/tegra114-nvidia-tegratab-common.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra114-nvidia-tegratab-common.dtsi
@@ -940,6 +940,48 @@ pwm@7000a000 {
status = "okay";
};
+ gen1_i2c: i2c@7000c000 {
+ status = "okay";
+ clock-frequency = <100000>;
+
+ fuel-gauge@36 {
+ compatible = "maxim,max17048";
+ reg = <0x36>;
+
+ interrupt-parent = <&gpio>;
+ interrupts = <TEGRA_GPIO(Q, 5) IRQ_TYPE_EDGE_FALLING>;
+
+ monitored-battery = <&battery>;
+ power-supplies = <&bq24193>;
+
+ maxim,alert-low-soc-level = <10>;
+ maxim,double-soc;
+
+ wakeup-source;
+ };
+
+ bq24193: charger@6b {
+ compatible = "ti,bq24193";
+ reg = <0x6b>;
+
+ interrupt-parent = <&gpio>;
+ interrupts = <TEGRA_GPIO(J, 0) IRQ_TYPE_EDGE_FALLING>;
+
+ ce-gpios = <&gpio TEGRA_GPIO(I, 4) GPIO_ACTIVE_LOW>;
+
+ monitored-battery = <&battery>;
+
+ omit-battery-class;
+ ti,system-minimum-microvolt = <3100000>;
+
+ usb_otg_vbus: usb-otg-vbus {
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+ };
+ };
+
i2c@7000d000 {
status = "okay";
clock-frequency = <400000>;
@@ -954,6 +996,15 @@ palmas: pmic@58 {
ti,system-power-controller;
+ palmas_extcon: extcon {
+ compatible = "ti,palmas-usb-vid";
+
+ ti,enable-vbus-detection;
+ ti,enable-id-detection;
+
+ ti,wakeup;
+ };
+
palmas_gpio: gpio {
compatible = "ti,palmas-gpio";
gpio-controller;
@@ -1210,19 +1261,34 @@ mmc@78000600 {
non-removable;
};
+ /* Micro USB */
usb@7d000000 {
+ compatible = "nvidia,tegra114-udc";
status = "okay";
+ dr_mode = "otg";
+
+ hnp-disable;
+ srp-disable;
+ adp-disable;
+
+ usb-role-switch;
+ extcon = <&bq24193>, <&palmas_extcon>; /* vbus, id */
+ vbus-supply = <&usb_otg_vbus>;
+
+ port {
+ usb_in: endpoint {
+ remote-endpoint = <&usb_connector_out>;
+ };
+ };
};
usb-phy@7d000000 {
status = "okay";
+ dr_mode = "otg";
nvidia,xcvr-setup = <7>;
nvidia,xcvr-lsfslew = <2>;
nvidia,xcvr-lsrslew = <2>;
- interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
- /* Should be changed to "otg" once we have vbus_supply */
- /* As of now, USB devices need to be powered externally */
- dr_mode = "host";
+ vbus-supply = <&avdd_usb>;
};
backlight: backlight {
@@ -1235,6 +1301,19 @@ backlight: backlight {
power-supply = <&vdd_3v7_bl>;
};
+ battery: battery-cell {
+ compatible = "simple-battery";
+ device-chemistry = "lithium-ion-polymer";
+
+ charge-full-design-microamp-hours = <4100000>;
+ energy-full-design-microwatt-hours = <15100000>;
+
+ precharge-current-microamp = <256000>;
+ charge-term-current-microamp = <256000>;
+
+ operating-range-celsius = <0 45>;
+ };
+
clk32k_in: clock-32k {
compatible = "fixed-clock";
clock-frequency = <32768>;
@@ -1242,6 +1321,17 @@ clk32k_in: clock-32k {
#clock-cells = <0>;
};
+ connector-usb {
+ compatible = "usb-b-connector";
+ type = "micro";
+
+ port {
+ usb_connector_out: endpoint {
+ remote-endpoint = <&usb_in>;
+ };
+ };
+ };
+
gpio-keys {
compatible = "gpio-keys";
--
2.53.0
next prev parent reply other threads:[~2026-11-22 20:14 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-22 20:13 [PATCH v1 00/18] [WIP] ARM: tegra: Update Tegra Note 7 configuration Svyatoslav Ryhel
2026-11-22 20:13 ` [PATCH v1 01/18] dt-bindings: ARM: tegra: Document Tegra Note 7 variants Svyatoslav Ryhel
2026-11-22 20:13 ` [PATCH v1 02/18] ARM: tegra: Diverge Tegra Note 7 device tree to support its common versions Svyatoslav Ryhel
2026-11-22 20:13 ` [PATCH v1 03/18] ARM: tegra: tegratab: Upgrade powerlines configuration Svyatoslav Ryhel
2026-11-22 20:13 ` [PATCH v1 04/18] ARM: tegra: tegratab: Add pinmux node Svyatoslav Ryhel
2026-11-22 20:13 ` [PATCH v1 05/18] ARM: tegra: tegratab: Bind VDE device Svyatoslav Ryhel
2026-11-22 20:13 ` Svyatoslav Ryhel [this message]
2026-11-22 20:13 ` [PATCH v1 07/18] ARM: tegra: tegratab: Configure MMC devices Svyatoslav Ryhel
2026-11-22 20:13 ` [PATCH v1 08/18] ARM: tegra: tegratab: Configure wireless devices Svyatoslav Ryhel
2026-11-22 20:13 ` [PATCH v1 09/18] ARM: tegra: tegratab: Add thermal configuration Svyatoslav Ryhel
2026-11-22 20:13 ` [PATCH v1 10/18] ARM: tegra: tegratab: Configure HDMI Svyatoslav Ryhel
2026-11-22 20:14 ` [PATCH v1 11/18] ARM: tegra: tegratab: Add audio codec and sound card configuration Svyatoslav Ryhel
2026-11-22 20:14 ` [PATCH v1 12/18] ARM: tegra: tegratab: Add common sensor nodes Svyatoslav Ryhel
2026-11-22 20:14 ` [PATCH v1 13/18] ARM: tegra: tegratab: Add MC and EMC timing nodes Svyatoslav Ryhel
2026-11-22 20:14 ` [PATCH v1 14/18] ARM: tegra: tegratab: Add CPU DFLL clock node Svyatoslav Ryhel
2026-11-22 20:14 ` [PATCH v1 15/18] ARM: tegra: tegratab: Update GPIO keys and switches Svyatoslav Ryhel
2026-11-22 20:14 ` [PATCH v1 16/18] ARM: tegra: tegratab: Update aliases, chosen and memory nodes Svyatoslav Ryhel
2026-11-22 20:14 ` [PATCH v1 17/18] ARM: tegra: tegratab: Add video input configuration Svyatoslav Ryhel
2026-11-22 20:14 ` [PATCH v1 18/18] ARM: tegra: tegratab: Add panel rotation Svyatoslav Ryhel
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20261122201407.23742-7-clamor95@gmail.com \
--to=clamor95@gmail.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=jonathanh@nvidia.com \
--cc=krzk+dt@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-tegra@vger.kernel.org \
--cc=mperttunen@nvidia.com \
--cc=robh@kernel.org \
--cc=thierry.reding@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox