From: Shawn Guo <shengchao.guo@oss.qualcomm.com>
To: Bjorn Andersson <andersson@kernel.org>
Cc: Konrad Dybcio <konradybcio@kernel.org>,
Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
Bartosz Golaszewski <brgl@kernel.org>,
Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>,
Yu Zhang <yu.zhang@oss.qualcomm.com>,
devicetree@vger.kernel.org, linux-arm-msm@vger.kernel.org,
linux-kernel@vger.kernel.org,
Abel Vesa <abel.vesa@oss.qualcomm.com>,
Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Subject: Re: [PATCH v2 1/5] arm64: dts: qcom: nord: Add PCIe PHY and controller nodes
Date: Sat, 10 Oct 2026 10:34:11 +0800 [thread overview]
Message-ID: <asmkI-UO5oMtrqsF@QCOM-aGQu4IUr3Y> (raw)
In-Reply-To: <20260915015632.283642-2-shengchao.guo@oss.qualcomm.com>
On Tue, Sep 15, 2026 at 09:56:28AM +0800, Shawn Guo wrote:
> From: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
>
> Nord has four PCIe controllers backed by a single quadfurcated Gen5
> QMP PHY with four ports (A/B/C/D) and a common PCIe SMMU. The ports
> can be ganged into x16, x8+x8, x8+x4+x4 or x8+x4+x2+x2 topologies; the
> topology in effect is selected by firmware through the TCSR link-config
> mode register, which the PHY driver reads at probe time. Describe the
> x8+x4+x2+x2 topology, i.e. all four controllers usable, as that is the
> configuration the boards ship with.
>
> Add the controller and SMMU nodes to nord.dtsi, and the PHY node along
> with the per-controller clocks, resets, GDSCs, interconnects, OPP tables
> and TLMM pin states to nord-embedded.dtsi. The four PCIe pipe clocks
> also become available now, so hook them up as GCC parents in place of
> the <0> placeholders.
>
> The controllers and the PHY are left disabled here and enabled per
> board.
>
> Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
> Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
> Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
> Signed-off-by: Shawn Guo <shengchao.guo@oss.qualcomm.com>
> ---
> arch/arm64/boot/dts/qcom/nord-embedded.dtsi | 926 +++++++++++++++++++-
> arch/arm64/boot/dts/qcom/nord.dtsi | 297 +++++++
> 2 files changed, 1219 insertions(+), 4 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/nord-embedded.dtsi b/arch/arm64/boot/dts/qcom/nord-embedded.dtsi
> index c7ac2e66632e..6e79f3cb20e9 100644
> --- a/arch/arm64/boot/dts/qcom/nord-embedded.dtsi
> +++ b/arch/arm64/boot/dts/qcom/nord-embedded.dtsi
> @@ -342,6 +342,738 @@ &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>,
> pinctrl-names = "default";
> };
>
> +&pcie0 {
> + clocks = <&gcc GCC_PCIE_A_AUX_CLK>,
> + <&gcc GCC_PCIE_A_CFG_AHB_CLK>,
> + <&gcc GCC_PCIE_A_MSTR_AXI_CLK>,
> + <&gcc GCC_PCIE_A_SLV_AXI_CLK>,
> + <&gcc GCC_PCIE_A_SLV_Q2A_AXI_CLK>;
> + clock-names = "aux",
> + "cfg",
> + "bus_master",
> + "bus_slave",
> + "slave_q2a";
> +
> + assigned-clocks = <&gcc GCC_PCIE_A_AUX_CLK>;
> + assigned-clock-rates = <19200000>;
> +
> + interconnects = <&pcie_data_inbound MASTER_PCIE_0 QCOM_ICC_TAG_ALWAYS
> + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
> + <&hscnoc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
> + &config_noc SLAVE_PCIE_0 QCOM_ICC_TAG_ALWAYS>;
> + interconnect-names = "pcie-mem",
> + "cpu-pcie";
> +
> + power-domains = <&gcc GCC_PCIE_A_GDSC>;
> +
> + resets = <&gcc GCC_PCIE_A_BCR>,
> + <&gcc GCC_PCIE_A_LINK_DOWN_BCR>;
> + reset-names = "pci",
> + "link_down";
> +
> + pinctrl-0 = <&pcie0_default>;
> + pinctrl-names = "default";
> +
> + operating-points-v2 = <&pcie0_opp_table>;
> +
> + pcie0_opp_table: opp-table {
> + compatible = "operating-points-v2";
> +
> + /* GEN 1 x1 */
> + opp-2500000-1 {
> + opp-hz = /bits/ 64 <2500000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <250000 1>;
> + opp-level = <1>;
> + };
> +
> + /* GEN 1 x2 */
> + opp-5000000-1 {
> + opp-hz = /bits/ 64 <5000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <500000 1>;
> + opp-level = <1>;
> + };
> +
> + /* GEN 1 x4 */
> + opp-10000000-1 {
> + opp-hz = /bits/ 64 <10000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <1000000 1>;
> + opp-level = <1>;
> + };
> +
> + /* GEN 1 x8 */
> + opp-20000000-1 {
> + opp-hz = /bits/ 64 <20000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <2000000 1>;
> + opp-level = <1>;
> + };
> +
> + /* GEN 1 x16 */
> + opp-40000000-1 {
> + opp-hz = /bits/ 64 <40000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <4000000 1>;
> + opp-level = <1>;
> + };
> +
> + /* GEN 2 x1 */
> + opp-5000000-2 {
> + opp-hz = /bits/ 64 <5000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <500000 1>;
> + opp-level = <2>;
> + };
> +
> + /* GEN 2 x2 */
> + opp-10000000-2 {
> + opp-hz = /bits/ 64 <10000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <1000000 1>;
> + opp-level = <2>;
> + };
> +
> + /* GEN 2 x4 */
> + opp-20000000-2 {
> + opp-hz = /bits/ 64 <20000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <2000000 1>;
> + opp-level = <2>;
> + };
> +
> + /* GEN 2 x8 */
> + opp-40000000-2 {
> + opp-hz = /bits/ 64 <40000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <4000000 1>;
> + opp-level = <2>;
> + };
> +
> + /* GEN 2 x16 */
> + opp-80000000-2 {
> + opp-hz = /bits/ 64 <80000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <8000000 1>;
> + opp-level = <2>;
> + };
> +
> + /* GEN 3 x1 */
> + opp-8000000-3 {
> + opp-hz = /bits/ 64 <8000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <984500 1>;
> + opp-level = <3>;
> + };
> +
> + /* GEN 3 x2 */
> + opp-16000000-3 {
> + opp-hz = /bits/ 64 <16000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <1969000 1>;
> + opp-level = <3>;
> + };
> +
> + /* GEN 3 x4 */
> + opp-32000000-3 {
> + opp-hz = /bits/ 64 <32000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <3938000 1>;
> + opp-level = <3>;
> + };
> +
> + /* GEN 3 x8 */
> + opp-64000000-3 {
> + opp-hz = /bits/ 64 <64000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <7876000 1>;
> + opp-level = <3>;
> + };
> +
> + /* GEN 3 x16 */
> + opp-128000000-3 {
> + opp-hz = /bits/ 64 <128000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <15753000 1>;
> + opp-level = <3>;
> + };
> +
> + /* GEN 4 x1 */
> + opp-16000000-4 {
> + opp-hz = /bits/ 64 <16000000>;
> + required-opps = <&rpmhpd_opp_svs>;
> + opp-peak-kBps = <1969000 1>;
> + opp-level = <4>;
> + };
> +
> + /* GEN 4 x2 */
> + opp-32000000-4 {
> + opp-hz = /bits/ 64 <32000000>;
> + required-opps = <&rpmhpd_opp_svs>;
> + opp-peak-kBps = <3938000 1>;
> + opp-level = <4>;
> + };
> +
> + /* GEN 4 x4 */
> + opp-64000000-4 {
> + opp-hz = /bits/ 64 <64000000>;
> + required-opps = <&rpmhpd_opp_svs>;
> + opp-peak-kBps = <7876000 1>;
> + opp-level = <4>;
> + };
> +
> + /* GEN 4 x8 */
> + opp-128000000-4 {
> + opp-hz = /bits/ 64 <128000000>;
> + required-opps = <&rpmhpd_opp_svs>;
> + opp-peak-kBps = <15753000 1>;
> + opp-level = <4>;
> + };
> +
> + /* GEN 4 x16 */
> + opp-256000000-4 {
> + opp-hz = /bits/ 64 <256000000>;
> + required-opps = <&rpmhpd_opp_svs>;
> + opp-peak-kBps = <31506000 1>;
> + opp-level = <4>;
> + };
> +
> + /* GEN 5 x1 */
> + opp-32000000-5 {
> + opp-hz = /bits/ 64 <32000000>;
> + required-opps = <&rpmhpd_opp_nom>;
> + opp-peak-kBps = <3938000 1>;
> + opp-level = <5>;
> + };
> +
> + /* GEN 5 x2 */
> + opp-64000000-5 {
> + opp-hz = /bits/ 64 <64000000>;
> + required-opps = <&rpmhpd_opp_nom>;
> + opp-peak-kBps = <7876000 1>;
> + opp-level = <5>;
> + };
> +
> + /* GEN 5 x4 */
> + opp-128000000-5 {
> + opp-hz = /bits/ 64 <128000000>;
> + required-opps = <&rpmhpd_opp_nom>;
> + opp-peak-kBps = <15753000 1>;
> + opp-level = <5>;
> + };
> +
> + /* GEN 5 x8 */
> + opp-256000000-5 {
> + opp-hz = /bits/ 64 <256000000>;
> + required-opps = <&rpmhpd_opp_nom>;
> + opp-peak-kBps = <31506000 1>;
> + opp-level = <5>;
> + };
> +
> + /* GEN 5 x16 */
> + opp-512000000-5 {
> + opp-hz = /bits/ 64 <512000000>;
> + required-opps = <&rpmhpd_opp_nom>;
> + opp-peak-kBps = <63012000 1>;
> + opp-level = <5>;
> + };
> + };
> +};
> +
> +&pcie0_port0 {
> + phys = <&pcie_phy 0>;
> +};
> +
> +&pcie1 {
> + clocks = <&gcc GCC_PCIE_B_AUX_CLK>,
> + <&gcc GCC_PCIE_B_CFG_AHB_CLK>,
> + <&gcc GCC_PCIE_B_MSTR_AXI_CLK>,
> + <&gcc GCC_PCIE_B_SLV_AXI_CLK>,
> + <&gcc GCC_PCIE_B_SLV_Q2A_AXI_CLK>;
> + clock-names = "aux",
> + "cfg",
> + "bus_master",
> + "bus_slave",
> + "slave_q2a";
> +
> + assigned-clocks = <&gcc GCC_PCIE_B_AUX_CLK>;
> + assigned-clock-rates = <19200000>;
> +
> + interconnects = <&pcie_data_inbound MASTER_PCIE_1 QCOM_ICC_TAG_ALWAYS
> + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
> + <&hscnoc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
> + &config_noc SLAVE_PCIE_1 QCOM_ICC_TAG_ALWAYS>;
> + interconnect-names = "pcie-mem",
> + "cpu-pcie";
> +
> + power-domains = <&gcc GCC_PCIE_B_GDSC>;
> +
> + resets = <&gcc GCC_PCIE_B_BCR>,
> + <&gcc GCC_PCIE_B_LINK_DOWN_BCR>;
> + reset-names = "pci",
> + "link_down";
> +
> + pinctrl-0 = <&pcie1_default>;
> + pinctrl-names = "default";
> +
> + operating-points-v2 = <&pcie1_opp_table>;
> +
> + pcie1_opp_table: opp-table {
> + compatible = "operating-points-v2";
> +
> + /* GEN 1 x1 */
> + opp-2500000-1 {
> + opp-hz = /bits/ 64 <2500000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <250000 1>;
> + opp-level = <1>;
> + };
> +
> + /* GEN 1 x2 */
> + opp-5000000-1 {
> + opp-hz = /bits/ 64 <5000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <500000 1>;
> + opp-level = <1>;
> + };
> +
> + /* GEN 1 x4 */
> + opp-10000000-1 {
> + opp-hz = /bits/ 64 <10000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <1000000 1>;
> + opp-level = <1>;
> + };
> +
> + /* GEN 1 x8 */
> + opp-20000000-1 {
> + opp-hz = /bits/ 64 <20000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <2000000 1>;
> + opp-level = <1>;
> + };
> +
> + /* GEN 2 x1 */
> + opp-5000000-2 {
> + opp-hz = /bits/ 64 <5000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <500000 1>;
> + opp-level = <2>;
> + };
> +
> + /* GEN 2 x2 */
> + opp-10000000-2 {
> + opp-hz = /bits/ 64 <10000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <1000000 1>;
> + opp-level = <2>;
> + };
> +
> + /* GEN 2 x4 */
> + opp-20000000-2 {
> + opp-hz = /bits/ 64 <20000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <2000000 1>;
> + opp-level = <2>;
> + };
> +
> + /* GEN 2 x8 */
> + opp-40000000-2 {
> + opp-hz = /bits/ 64 <40000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <4000000 1>;
> + opp-level = <2>;
> + };
> +
> + /* GEN 3 x1 */
> + opp-8000000-3 {
> + opp-hz = /bits/ 64 <8000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <984500 1>;
> + opp-level = <3>;
> + };
> +
> + /* GEN 3 x2 */
> + opp-16000000-3 {
> + opp-hz = /bits/ 64 <16000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <1969000 1>;
> + opp-level = <3>;
> + };
> +
> + /* GEN 3 x4 */
> + opp-32000000-3 {
> + opp-hz = /bits/ 64 <32000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <3938000 1>;
> + opp-level = <3>;
> + };
> +
> + /* GEN 3 x8 */
> + opp-64000000-3 {
> + opp-hz = /bits/ 64 <64000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <7876000 1>;
> + opp-level = <3>;
> + };
> +
> + /* GEN 4 x1 */
> + opp-16000000-4 {
> + opp-hz = /bits/ 64 <16000000>;
> + required-opps = <&rpmhpd_opp_svs>;
> + opp-peak-kBps = <1969000 1>;
> + opp-level = <4>;
> + };
> +
> + /* GEN 4 x2 */
> + opp-32000000-4 {
> + opp-hz = /bits/ 64 <32000000>;
> + required-opps = <&rpmhpd_opp_svs>;
> + opp-peak-kBps = <3938000 1>;
> + opp-level = <4>;
> + };
> +
> + /* GEN 4 x4 */
> + opp-64000000-4 {
> + opp-hz = /bits/ 64 <64000000>;
> + required-opps = <&rpmhpd_opp_svs>;
> + opp-peak-kBps = <7876000 1>;
> + opp-level = <4>;
> + };
> +
> + /* GEN 4 x8 */
> + opp-128000000-4 {
> + opp-hz = /bits/ 64 <128000000>;
> + required-opps = <&rpmhpd_opp_svs>;
> + opp-peak-kBps = <15753000 1>;
> + opp-level = <4>;
> + };
> +
> + /* GEN 5 x1 */
> + opp-32000000-5 {
> + opp-hz = /bits/ 64 <32000000>;
> + required-opps = <&rpmhpd_opp_nom>;
> + opp-peak-kBps = <3938000 1>;
> + opp-level = <5>;
> + };
> +
> + /* GEN 5 x2 */
> + opp-64000000-5 {
> + opp-hz = /bits/ 64 <64000000>;
> + required-opps = <&rpmhpd_opp_nom>;
> + opp-peak-kBps = <7876000 1>;
> + opp-level = <5>;
> + };
> +
> + /* GEN 5 x4 */
> + opp-128000000-5 {
> + opp-hz = /bits/ 64 <128000000>;
> + required-opps = <&rpmhpd_opp_nom>;
> + opp-peak-kBps = <15753000 1>;
> + opp-level = <5>;
> + };
> +
> + /* GEN 5 x8 */
> + opp-256000000-5 {
> + opp-hz = /bits/ 64 <256000000>;
> + required-opps = <&rpmhpd_opp_nom>;
> + opp-peak-kBps = <31506000 1>;
> + opp-level = <5>;
> + };
> + };
> +};
> +
> +&pcie1_port0 {
> + phys = <&pcie_phy 1>;
> +};
> +
> +&pcie2 {
> + clocks = <&gcc GCC_PCIE_C_AUX_CLK>,
> + <&gcc GCC_PCIE_C_CFG_AHB_CLK>,
> + <&gcc GCC_PCIE_C_MSTR_AXI_CLK>,
> + <&gcc GCC_PCIE_C_SLV_AXI_CLK>,
> + <&gcc GCC_PCIE_C_SLV_Q2A_AXI_CLK>;
> + clock-names = "aux",
> + "cfg",
> + "bus_master",
> + "bus_slave",
> + "slave_q2a";
> +
> + assigned-clocks = <&gcc GCC_PCIE_C_AUX_CLK>;
> + assigned-clock-rates = <19200000>;
> +
> + interconnects = <&pcie_data_inbound MASTER_PCIE_2 QCOM_ICC_TAG_ALWAYS
> + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
> + <&hscnoc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
> + &config_noc SLAVE_PCIE_2 QCOM_ICC_TAG_ALWAYS>;
> + interconnect-names = "pcie-mem",
> + "cpu-pcie";
> +
> + power-domains = <&gcc GCC_PCIE_C_GDSC>;
> +
> + resets = <&gcc GCC_PCIE_C_BCR>,
> + <&gcc GCC_PCIE_C_LINK_DOWN_BCR>;
> + reset-names = "pci",
> + "link_down";
> +
> + pinctrl-0 = <&pcie2_default>;
> + pinctrl-names = "default";
> +
> + operating-points-v2 = <&pcie2_opp_table>;
> +
> + pcie2_opp_table: opp-table {
> + compatible = "operating-points-v2";
> +
> + /* GEN 1 x1 */
> + opp-2500000-1 {
> + opp-hz = /bits/ 64 <2500000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <250000 1>;
> + opp-level = <1>;
> + };
> +
> + /* GEN 1 x2 */
> + opp-5000000-1 {
> + opp-hz = /bits/ 64 <5000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <500000 1>;
> + opp-level = <1>;
> + };
> +
> + /* GEN 1 x4 */
> + opp-10000000-1 {
> + opp-hz = /bits/ 64 <10000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <1000000 1>;
> + opp-level = <1>;
> + };
> +
> + /* GEN 2 x1 */
> + opp-5000000-2 {
> + opp-hz = /bits/ 64 <5000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <500000 1>;
> + opp-level = <2>;
> + };
> +
> + /* GEN 2 x2 */
> + opp-10000000-2 {
> + opp-hz = /bits/ 64 <10000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <1000000 1>;
> + opp-level = <2>;
> + };
> +
> + /* GEN 2 x4 */
> + opp-20000000-2 {
> + opp-hz = /bits/ 64 <20000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <2000000 1>;
> + opp-level = <2>;
> + };
> +
> + /* GEN 3 x1 */
> + opp-8000000-3 {
> + opp-hz = /bits/ 64 <8000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <984500 1>;
> + opp-level = <3>;
> + };
> +
> + /* GEN 3 x2 */
> + opp-16000000-3 {
> + opp-hz = /bits/ 64 <16000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <1969000 1>;
> + opp-level = <3>;
> + };
> +
> + /* GEN 3 x4 */
> + opp-32000000-3 {
> + opp-hz = /bits/ 64 <32000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <3938000 1>;
> + opp-level = <3>;
> + };
> +
> + /* GEN 4 x1 */
> + opp-16000000-4 {
> + opp-hz = /bits/ 64 <16000000>;
> + required-opps = <&rpmhpd_opp_svs>;
> + opp-peak-kBps = <1969000 1>;
> + opp-level = <4>;
> + };
> +
> + /* GEN 4 x2 */
> + opp-32000000-4 {
> + opp-hz = /bits/ 64 <32000000>;
> + required-opps = <&rpmhpd_opp_svs>;
> + opp-peak-kBps = <3938000 1>;
> + opp-level = <4>;
> + };
> +
> + /* GEN 4 x4 */
> + opp-64000000-4 {
> + opp-hz = /bits/ 64 <64000000>;
> + required-opps = <&rpmhpd_opp_svs>;
> + opp-peak-kBps = <7876000 1>;
> + opp-level = <4>;
> + };
> +
> + /* GEN 5 x1 */
> + opp-32000000-5 {
> + opp-hz = /bits/ 64 <32000000>;
> + required-opps = <&rpmhpd_opp_nom>;
> + opp-peak-kBps = <3938000 1>;
> + opp-level = <5>;
> + };
> +
> + /* GEN 5 x2 */
> + opp-64000000-5 {
> + opp-hz = /bits/ 64 <64000000>;
> + required-opps = <&rpmhpd_opp_nom>;
> + opp-peak-kBps = <7876000 1>;
> + opp-level = <5>;
> + };
> +
> + /* GEN 5 x4 */
> + opp-128000000-5 {
> + opp-hz = /bits/ 64 <128000000>;
> + required-opps = <&rpmhpd_opp_nom>;
> + opp-peak-kBps = <15753000 1>;
> + opp-level = <5>;
> + };
> + };
> +};
> +
> +&pcie2_port0 {
> + phys = <&pcie_phy 2>;
> +};
> +
> +&pcie3 {
> + clocks = <&gcc GCC_PCIE_D_AUX_CLK>,
> + <&gcc GCC_PCIE_D_CFG_AHB_CLK>,
> + <&gcc GCC_PCIE_D_MSTR_AXI_CLK>,
> + <&gcc GCC_PCIE_D_SLV_AXI_CLK>,
> + <&gcc GCC_PCIE_D_SLV_Q2A_AXI_CLK>;
> + clock-names = "aux",
> + "cfg",
> + "bus_master",
> + "bus_slave",
> + "slave_q2a";
> +
> + assigned-clocks = <&gcc GCC_PCIE_D_AUX_CLK>;
> + assigned-clock-rates = <19200000>;
> +
> + interconnects = <&pcie_data_inbound MASTER_PCIE_3 QCOM_ICC_TAG_ALWAYS
> + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
> + <&hscnoc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
> + &config_noc SLAVE_PCIE_3 QCOM_ICC_TAG_ALWAYS>;
> + interconnect-names = "pcie-mem",
> + "cpu-pcie";
> +
> + power-domains = <&gcc GCC_PCIE_D_GDSC>;
> +
> + resets = <&gcc GCC_PCIE_D_BCR>,
> + <&gcc GCC_PCIE_D_LINK_DOWN_BCR>;
> + reset-names = "pci",
> + "link_down";
> +
> + pinctrl-0 = <&pcie3_default>;
> + pinctrl-names = "default";
> +
> + operating-points-v2 = <&pcie3_opp_table>;
> +
> + pcie3_opp_table: opp-table {
> + compatible = "operating-points-v2";
> +
> + /* GEN 1 x1 */
> + opp-2500000-1 {
> + opp-hz = /bits/ 64 <2500000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <250000 1>;
> + opp-level = <1>;
> + };
> +
> + /* GEN 1 x2 */
> + opp-5000000-1 {
> + opp-hz = /bits/ 64 <5000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <500000 1>;
> + opp-level = <1>;
> + };
> +
> + /* GEN 2 x1 */
> + opp-5000000-2 {
> + opp-hz = /bits/ 64 <5000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <500000 1>;
> + opp-level = <2>;
> + };
> +
> + /* GEN 2 x2 */
> + opp-10000000-2 {
> + opp-hz = /bits/ 64 <10000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <1000000 1>;
> + opp-level = <2>;
> + };
> +
> + /* GEN 3 x1 */
> + opp-8000000-3 {
> + opp-hz = /bits/ 64 <8000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <984500 1>;
> + opp-level = <3>;
> + };
> +
> + /* GEN 3 x2 */
> + opp-16000000-3 {
> + opp-hz = /bits/ 64 <16000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + opp-peak-kBps = <1969000 1>;
> + opp-level = <3>;
> + };
> +
> + /* GEN 4 x1 */
> + opp-16000000-4 {
> + opp-hz = /bits/ 64 <16000000>;
> + required-opps = <&rpmhpd_opp_svs>;
> + opp-peak-kBps = <1969000 1>;
> + opp-level = <4>;
> + };
> +
> + /* GEN 4 x2 */
> + opp-32000000-4 {
> + opp-hz = /bits/ 64 <32000000>;
> + required-opps = <&rpmhpd_opp_svs>;
> + opp-peak-kBps = <3938000 1>;
> + opp-level = <4>;
> + };
> +
> + /* GEN 5 x1 */
> + opp-32000000-5 {
> + opp-hz = /bits/ 64 <32000000>;
> + required-opps = <&rpmhpd_opp_nom>;
> + opp-peak-kBps = <3938000 1>;
> + opp-level = <5>;
> + };
> +
> + /* GEN 5 x2 */
> + opp-64000000-5 {
> + opp-hz = /bits/ 64 <64000000>;
> + required-opps = <&rpmhpd_opp_nom>;
> + opp-peak-kBps = <7876000 1>;
> + opp-level = <5>;
> + };
> + };
> +};
> +
> +&pcie3_port0 {
> + phys = <&pcie_phy 3>;
> +};
> +
> &qupv3_0 {
> clocks = <&segcc SE_GCC_QUPV3_WRAP0_M_AHB_CLK>,
> <&segcc SE_GCC_QUPV3_WRAP0_S_AHB_CLK>;
> @@ -704,10 +1436,10 @@ gcc: clock-controller@100000 {
> reg = <0x0 0x00100000 0x0 0x1f4200>;
> clocks = <&bi_tcxo_div2>,
> <&sleep_clk>,
> - <0>,
> - <0>,
> - <0>,
> - <0>;
> + <&pcie_phy 0>,
> + <&pcie_phy 1>,
> + <&pcie_phy 2>,
> + <&pcie_phy 3>;
> #clock-cells = <1>;
> #reset-cells = <1>;
> #power-domain-cells = <1>;
> @@ -774,6 +1506,100 @@ mmss_noc: interconnect@1780000 {
> qcom,bcm-voters = <&apps_bcm_voter>;
> };
>
> + pcie_phy: phy@1b00000 {
> + compatible = "qcom,nord-qmp-gen5x16-pcie-phy";
> +
> + reg = <0x0 0x01b00000 0x0 0x10000>,
> + <0x0 0x01b10000 0x0 0x10000>,
> + <0x0 0x01b20000 0x0 0x10000>,
> + <0x0 0x01b30000 0x0 0x10000>;
> + reg-names = "port_a",
> + "port_b",
> + "port_c",
> + "port_d";
> +
> + clocks = <&gcc GCC_PCIE_A_PHY_AUX_CLK>,
> + <&gcc GCC_PCIE_A_CFG_AHB_CLK>,
> + <&tcsrcc TCSR_PCIE_CLKREF_EN>,
> + <&gcc GCC_PCIE_A_PHY_RCHNG_CLK>,
> + <&gcc GCC_PCIE_A_PIPE_CLK>,
> + <&gcc GCC_PCIE_B_PHY_AUX_CLK>,
> + <&gcc GCC_PCIE_B_CFG_AHB_CLK>,
> + <&gcc GCC_PCIE_B_PHY_RCHNG_CLK>,
> + <&gcc GCC_PCIE_B_PIPE_CLK>,
> + <&gcc GCC_PCIE_C_PHY_AUX_CLK>,
> + <&gcc GCC_PCIE_C_CFG_AHB_CLK>,
> + <&gcc GCC_PCIE_C_PHY_RCHNG_CLK>,
> + <&gcc GCC_PCIE_C_PIPE_CLK>,
> + <&gcc GCC_PCIE_D_PHY_AUX_CLK>,
> + <&gcc GCC_PCIE_D_CFG_AHB_CLK>,
> + <&gcc GCC_PCIE_D_PHY_RCHNG_CLK>,
> + <&gcc GCC_PCIE_D_PIPE_CLK>;
> + clock-names = "aux_a",
> + "cfg_ahb_a",
> + "ref",
> + "rchng_a",
> + "pipe_a",
> + "aux_b",
> + "cfg_ahb_b",
> + "rchng_b",
> + "pipe_b",
> + "aux_c",
> + "cfg_ahb_c",
> + "rchng_c",
> + "pipe_c",
> + "aux_d",
> + "cfg_ahb_d",
> + "rchng_d",
> + "pipe_d";
> +
> + assigned-clocks = <&gcc GCC_PCIE_A_PHY_RCHNG_CLK>,
> + <&gcc GCC_PCIE_B_PHY_RCHNG_CLK>,
> + <&gcc GCC_PCIE_C_PHY_RCHNG_CLK>,
> + <&gcc GCC_PCIE_D_PHY_RCHNG_CLK>;
> + assigned-clock-rates = <100000000>,
> + <100000000>,
> + <100000000>,
> + <100000000>;
> +
> + power-domains = <&gcc GCC_PCIE_A_PHY_GDSC>,
> + <&gcc GCC_PCIE_B_PHY_GDSC>,
> + <&gcc GCC_PCIE_C_PHY_GDSC>,
> + <&gcc GCC_PCIE_D_PHY_GDSC>;
> + power-domain-names = "port_a",
> + "port_b",
> + "port_c",
> + "port_d";
> +
> + resets = <&gcc GCC_PCIE_A_PHY_COM_BCR>,
> + <&gcc GCC_PCIE_A_NOCSR_COM_PHY_BCR>,
> + <&gcc GCC_PCIE_B_PHY_COM_BCR>,
> + <&gcc GCC_PCIE_B_NOCSR_COM_PHY_BCR>,
> + <&gcc GCC_PCIE_C_PHY_COM_BCR>,
> + <&gcc GCC_PCIE_C_NOCSR_COM_PHY_BCR>,
> + <&gcc GCC_PCIE_D_PHY_COM_BCR>,
> + <&gcc GCC_PCIE_D_NOCSR_COM_PHY_BCR>;
> + reset-names = "port_a",
> + "port_a_nocsr",
> + "port_b",
> + "port_b_nocsr",
> + "port_c",
> + "port_c_nocsr",
> + "port_d",
> + "port_d_nocsr";
> +
> + qcom,link-mode = <&tcsr 0x71050>;
> +
> + #clock-cells = <1>;
> + clock-output-names = "pcie_a_pipe_clk",
> + "pcie_b_pipe_clk",
> + "pcie_c_pipe_clk",
> + "pcie_d_pipe_clk";
> + #phy-cells = <1>;
> +
> + status = "disabled";
> + };
> +
> pcie_cfg: interconnect@1ba0000 {
> compatible = "qcom,nord-pcie-cfg";
> reg = <0x0 0x01ba0000 0x0 0x7200>;
> @@ -998,6 +1824,98 @@ nsp_data_noc_3: interconnect@1fe00000 {
> };
>
> &tlmm {
> + pcie0_default: pcie0-default-state {
> + wake-pins {
> + pins = "gpio0";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + clkreq-pins {
> + pins = "gpio1";
> + function = "pcie0_clk_req_n";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + perst-pins {
> + pins = "gpio2";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-disable;
> + };
pcie0_clk_req_n is a SoC level pin function, so it has a good reason to
stay here. But wake and perst are board chosen GPIOs. I think they should
go to board DTS.
Shawn
> + };
> +
> + pcie1_default: pcie1-default-state {
> + wake-pins {
> + pins = "gpio3";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + clkreq-pins {
> + pins = "gpio4";
> + function = "pcie1_clk_req_n";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + perst-pins {
> + pins = "gpio5";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-disable;
> + };
> + };
> +
> + pcie2_default: pcie2-default-state {
> + wake-pins {
> + pins = "gpio6";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + clkreq-pins {
> + pins = "gpio7";
> + function = "pcie2_clk_req_n";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + perst-pins {
> + pins = "gpio8";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-disable;
> + };
> + };
> +
> + pcie3_default: pcie3-default-state {
> + wake-pins {
> + pins = "gpio9";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + clkreq-pins {
> + pins = "gpio10";
> + function = "pcie3_clk_req_n";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + perst-pins {
> + pins = "gpio11";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-disable;
> + };
> + };
> +
> qup_i2c0_default: qup-i2c0-default-state {
> pins = "gpio111", "gpio112";
> function = "qup0_se0";
> diff --git a/arch/arm64/boot/dts/qcom/nord.dtsi b/arch/arm64/boot/dts/qcom/nord.dtsi
> index 83760341456b..0fb292074b99 100644
> --- a/arch/arm64/boot/dts/qcom/nord.dtsi
> +++ b/arch/arm64/boot/dts/qcom/nord.dtsi
> @@ -1587,6 +1587,290 @@ rng: rng@10c3000 {
> reg = <0x0 0x010c3000 0x0 0x1000>;
> };
>
> + pcie0: pci@1b80000 {
> + compatible = "qcom,nord-pcie", "qcom,pcie-sa8775p";
> +
> + reg = <0x00 0x01b80000 0x00 0x00004000>,
> + <0x00 0x40000000 0x00 0x00000f20>,
> + <0x00 0x40000f20 0x00 0x000000a8>,
> + <0x00 0x40010000 0x00 0x00020000>,
> + <0x00 0x40100000 0x00 0x00100000>,
> + <0x00 0x01b84000 0x00 0x00001000>;
> + reg-names = "parf",
> + "dbi",
> + "elbi",
> + "atu",
> + "config",
> + "mhi";
> +
> + ranges = <0x01000000 0x0 0x00000000 0x0 0x40200000 0x0 0x100000>,
> + <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0xfd00000>;
> +
> + bus-range = <0x00 0xff>;
> + device_type = "pci";
> + linux,pci-domain = <0>;
> + num-lanes = <8>;
> +
> + #address-cells = <3>;
> + #size-cells = <2>;
> +
> + dma-coherent;
> +
> + interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "msi0",
> + "msi1",
> + "msi2",
> + "msi3",
> + "msi4",
> + "msi5",
> + "msi6",
> + "msi7",
> + "global";
> + #interrupt-cells = <1>;
> + interrupt-map-mask = <0 0 0 0x7>;
> + interrupt-map = <0 0 0 1 &intc 0 0 0 149 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 2 &intc 0 0 0 150 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 3 &intc 0 0 0 151 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 4 &intc 0 0 0 152 IRQ_TYPE_LEVEL_HIGH>;
> +
> + iommu-map = <0x0 &pcie_smmu 0x0000 0x10000>;
> +
> + msi-map = <0x0 &gic_its 0x80000 0x10000>;
> +
> + status = "disabled";
> +
> + pcie0_port0: pcie@0 {
> + compatible = "pciclass,0604";
> + reg = <0 0 0 0 0>;
> + bus-range = <0x01 0xff>;
> + device_type = "pci";
> + #address-cells = <3>;
> + #size-cells = <2>;
> + ranges;
> + };
> + };
> +
> + pcie1: pci@1b88000 {
> + compatible = "qcom,nord-pcie", "qcom,pcie-sa8775p";
> +
> + reg = <0x00 0x01b88000 0x00 0x00004000>,
> + <0x00 0x50000000 0x00 0x00000f20>,
> + <0x00 0x50000f20 0x00 0x000000a8>,
> + <0x00 0x50010000 0x00 0x00010000>,
> + <0x00 0x50100000 0x00 0x00100000>,
> + <0x00 0x01b8c000 0x00 0x00001000>;
> + reg-names = "parf",
> + "dbi",
> + "elbi",
> + "atu",
> + "config",
> + "mhi";
> +
> + ranges = <0x01000000 0x0 0x00000000 0x0 0x50200000 0x0 0x100000>,
> + <0x02000000 0x0 0x50300000 0x0 0x50300000 0x0 0xfd00000>;
> +
> + bus-range = <0x00 0xff>;
> + device_type = "pci";
> + linux,pci-domain = <1>;
> + num-lanes = <4>;
> +
> + #address-cells = <3>;
> + #size-cells = <2>;
> +
> + dma-coherent;
> +
> + interrupts = <GIC_SPI 834 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 833 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 845 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 842 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 824 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 349 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 949 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "msi0",
> + "msi1",
> + "msi2",
> + "msi3",
> + "msi4",
> + "msi5",
> + "msi6",
> + "msi7",
> + "global";
> + #interrupt-cells = <1>;
> + interrupt-map-mask = <0 0 0 0x7>;
> + interrupt-map = <0 0 0 1 &intc 0 0 0 835 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 2 &intc 0 0 0 351 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 3 &intc 0 0 0 830 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 4 &intc 0 0 0 348 IRQ_TYPE_LEVEL_HIGH>;
> +
> + msi-map = <0x0 &gic_its 0x90000 0x10000>;
> +
> + iommu-map = <0x0 &pcie_smmu 0x10000 0x10000>;
> +
> + status = "disabled";
> +
> + pcie1_port0: pcie@0 {
> + device_type = "pci";
> + compatible = "pciclass,0604";
> + reg = <0 0 0 0 0>;
> + bus-range = <0x01 0xff>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> + ranges;
> + };
> + };
> +
> + pcie2: pci@1b90000 {
> + compatible = "qcom,nord-pcie", "qcom,pcie-sa8775p";
> +
> + reg = <0x00 0x01b90000 0x00 0x00004000>,
> + <0x00 0x60000000 0x00 0x00000f20>,
> + <0x00 0x60000f20 0x00 0x000000a8>,
> + <0x00 0x60010000 0x00 0x00010000>,
> + <0x00 0x60100000 0x00 0x00100000>,
> + <0x00 0x01b94000 0x00 0x00001000>;
> + reg-names = "parf",
> + "dbi",
> + "elbi",
> + "atu",
> + "config",
> + "mhi";
> +
> + ranges = <0x01000000 0x0 0x00000000 0x0 0x60200000 0x0 0x100000>,
> + <0x02000000 0x0 0x60300000 0x0 0x60300000 0x0 0xfd00000>;
> +
> + bus-range = <0x00 0xff>;
> + device_type = "pci";
> + linux,pci-domain = <2>;
> + num-lanes = <2>;
> +
> + #address-cells = <3>;
> + #size-cells = <2>;
> +
> + dma-coherent;
> +
> + interrupts = <GIC_SPI 844 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 838 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 825 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 846 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 350 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 837 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 464 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "msi0",
> + "msi1",
> + "msi2",
> + "msi3",
> + "msi4",
> + "msi5",
> + "msi6",
> + "msi7",
> + "global";
> + #interrupt-cells = <1>;
> + interrupt-map-mask = <0 0 0 0x7>;
> + interrupt-map = <0 0 0 1 &intc 0 0 0 263 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 2 &intc 0 0 0 154 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 3 &intc 0 0 0 110 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 4 &intc 0 0 0 258 IRQ_TYPE_LEVEL_HIGH>;
> +
> + iommu-map = <0x0 &pcie_smmu 0x20000 0x10000>;
> +
> + msi-map = <0x0 &gic_its 0xa0000 0x10000>;
> +
> + status = "disabled";
> +
> + pcie2_port0: pcie@0 {
> + device_type = "pci";
> + compatible = "pciclass,0604";
> + reg = <0 0 0 0 0>;
> + bus-range = <0x01 0xff>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> + ranges;
> + };
> + };
> +
> + pcie3: pci@1b98000 {
> + compatible = "qcom,nord-pcie", "qcom,pcie-sa8775p";
> +
> + reg = <0x00 0x01b98000 0x00 0x00004000>,
> + <0x00 0x70000000 0x00 0x00000f20>,
> + <0x00 0x70000f20 0x00 0x000000a8>,
> + <0x00 0x70010000 0x00 0x00010000>,
> + <0x00 0x70100000 0x00 0x00100000>,
> + <0x00 0x01b9c000 0x00 0x00001000>;
> + reg-names = "parf",
> + "dbi",
> + "elbi",
> + "atu",
> + "config",
> + "mhi";
> +
> + ranges = <0x01000000 0x0 0x00000000 0x0 0x70200000 0x0 0x100000>,
> + <0x02000000 0x0 0x70300000 0x0 0x70300000 0x0 0xfd00000>;
> +
> + bus-range = <0x00 0xff>;
> + device_type = "pci";
> + linux,pci-domain = <3>;
> + num-lanes = <2>;
> +
> + #address-cells = <3>;
> + #size-cells = <2>;
> +
> + dma-coherent;
> +
> + interrupts = <GIC_SPI 364 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 831 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 659 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 840 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 823 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 241 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 465 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "msi0",
> + "msi1",
> + "msi2",
> + "msi3",
> + "msi4",
> + "msi5",
> + "msi6",
> + "msi7",
> + "global";
> + #interrupt-cells = <1>;
> + interrupt-map-mask = <0 0 0 0x7>;
> + interrupt-map = <0 0 0 1 &intc 0 0 0 111 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 2 &intc 0 0 0 246 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 3 &intc 0 0 0 239 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 4 &intc 0 0 0 234 IRQ_TYPE_LEVEL_HIGH>;
> +
> + msi-map = <0x0 &gic_its 0xb0000 0x10000>;
> +
> + iommu-map = <0x0 &pcie_smmu 0x30000 0x10000>;
> +
> + status = "disabled";
> +
> + pcie3_port0: pcie@0 {
> + device_type = "pci";
> + compatible = "pciclass,0604";
> + reg = <0 0 0 0 0>;
> + bus-range = <0x01 0xff>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> + ranges;
> + };
> + };
> +
> ufs_mem_hc: ufshc@1d44000 {
> compatible = "qcom,nord-ufshc",
> "qcom,ufshc",
> @@ -1736,6 +2020,19 @@ ipcc0: mailbox@9007000 {
> #mbox-cells = <2>;
> };
>
> + pcie_smmu: iommu@9980000 {
> + compatible = "arm,smmu-v3";
> + reg = <0x0 0x09980000 0x0 0x20000>;
> + interrupts = <GIC_SPI 898 IRQ_TYPE_EDGE_RISING>,
> + <GIC_SPI 900 IRQ_TYPE_EDGE_RISING>,
> + <GIC_SPI 902 IRQ_TYPE_EDGE_RISING>;
> + interrupt-names = "eventq",
> + "cmdq-sync",
> + "gerror";
> + dma-coherent;
> + #iommu-cells = <1>;
> + };
> +
> pdc: interrupt-controller@b220000 {
> compatible = "qcom,nord-pdc",
> "qcom,pdc";
> --
> 2.43.0
>
next prev parent reply other threads:[~2026-10-10 2:34 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-09-15 1:56 [PATCH v2 0/5] arm64: dts: qcom: nord: Add PCIe and WLAN support Shawn Guo
2026-09-15 1:56 ` [PATCH v2 1/5] arm64: dts: qcom: nord: Add PCIe PHY and controller nodes Shawn Guo
2026-10-10 2:34 ` Shawn Guo [this message]
2026-09-15 1:56 ` [PATCH v2 2/5] arm64: dts: qcom: nord-rrd: Enable PCIe controllers and PHY Shawn Guo
2026-09-15 1:56 ` [PATCH v2 3/5] arm64: dts: qcom: nord-ride-embedded: " Shawn Guo
2026-09-15 1:56 ` [PATCH v2 4/5] arm64: dts: qcom: nord-ride-embedded: Add WCN7850 WLAN support Shawn Guo
2026-09-15 1:56 ` [PATCH v2 5/5] arm64: dts: qcom: nord-rrd: " Shawn Guo
2026-09-28 1:56 ` [PATCH v2 0/5] arm64: dts: qcom: nord: Add PCIe and " Bjorn Andersson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=asmkI-UO5oMtrqsF@QCOM-aGQu4IUr3Y \
--to=shengchao.guo@oss.qualcomm.com \
--cc=abel.vesa@oss.qualcomm.com \
--cc=andersson@kernel.org \
--cc=bartosz.golaszewski@oss.qualcomm.com \
--cc=brgl@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=konradybcio@kernel.org \
--cc=krishna.chundru@oss.qualcomm.com \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh@kernel.org \
--cc=yu.zhang@oss.qualcomm.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox