* [PATCH V5 1/5] clocksource: imx-sysctr: Add internal clock divider handle
From: Anson.Huang @ 2019-07-10 6:30 UTC (permalink / raw)
To: catalin.marinas, will, robh+dt, mark.rutland, shawnguo, s.hauer,
kernel, festevam, linux-imx, daniel.lezcano, tglx,
leonard.crestez, aisheng.dong, daniel.baluta, ping.bai, l.stach,
abel.vesa, andrew.smirnov, ccaione, angus, agx, linux-arm-kernel,
linux-kernel, devicetree
Cc: Linux-imx
From: Anson Huang <Anson.Huang@nxp.com>
The system counter block guide states that the base clock is
internally divided by 3 before use, that means the clock input of
system counter defined in DT should be base clock which is normally
from OSC, and then internally divided by 3 before use.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
Changes since V4:
- to solve the clock driver probed after system counter driver issue, now we can easily switch to
use fixed clock defined in DT and get its rate, then divided by 3 to get real clock rate for
system counter driver, no need to add "clock-frequency" property in DT.
---
drivers/clocksource/timer-imx-sysctr.c | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/drivers/clocksource/timer-imx-sysctr.c b/drivers/clocksource/timer-imx-sysctr.c
index fd7d680..b7c80a3 100644
--- a/drivers/clocksource/timer-imx-sysctr.c
+++ b/drivers/clocksource/timer-imx-sysctr.c
@@ -20,6 +20,8 @@
#define SYS_CTR_EN 0x1
#define SYS_CTR_IRQ_MASK 0x2
+#define SYS_CTR_CLK_DIV 0x3
+
static void __iomem *sys_ctr_base;
static u32 cmpcr;
@@ -134,6 +136,9 @@ static int __init sysctr_timer_init(struct device_node *np)
if (ret)
return ret;
+ /* system counter clock is divided by 3 internally */
+ to_sysctr.of_clk.rate /= SYS_CTR_CLK_DIV;
+
sys_ctr_base = timer_of_base(&to_sysctr);
cmpcr = readl(sys_ctr_base + CMPCR);
cmpcr &= ~SYS_CTR_EN;
--
2.7.4
^ permalink raw reply related
* [PATCH V13 12/12] PCI: tegra: Add Tegra194 PCIe support
From: Vidya Sagar @ 2019-07-10 6:22 UTC (permalink / raw)
To: lorenzo.pieralisi, bhelgaas, robh+dt, mark.rutland,
thierry.reding, jonathanh, kishon, catalin.marinas, will.deacon,
jingoohan1, gustavo.pimentel
Cc: digetx, mperttunen, linux-pci, devicetree, linux-tegra,
linux-kernel, linux-arm-kernel, kthota, mmaddireddy, vidyas,
sagar.tv
In-Reply-To: <20190710062212.1745-1-vidyas@nvidia.com>
Add support for Synopsys DesignWare core IP based PCIe host controller
present in Tegra194 SoC.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
---
V13:
* Modified according to modifications in PATCH V13 01/12
V12:
* None
V11:
* None
V10:
* Used _relaxed() versions of readl() & writel()
V9:
* Made it dependent on ARCH_TEGRA_194_SOC directly
V8:
* Addressed review comments from Thierry
V7:
* Removed code around "nvidia,disable-aspm-states" DT property
* Refactored code to remove code duplication
V6:
* Addressed review comments from Thierry
V5:
* None
V4:
* None
V3:
* Changed 'nvidia,init-speed' to 'nvidia,init-link-speed'
* Changed 'nvidia,pex-wake' to 'nvidia,wake-gpios'
* Removed .runtime_suspend() & .runtime_resume() implementations
V2:
* Made CONFIG_PCIE_TEGRA194 as 'm' by default from its previous 'y' state
* Modified code as per changes made to DT documentation
* Refactored code to address Bjorn & Thierry's review comments
* Added goto to avoid recursion in tegra_pcie_dw_host_init() API
* Merged .scan_bus() of dw_pcie_host_ops implementation to tegra_pcie_dw_host_init() API
drivers/pci/controller/dwc/Kconfig | 10 +
drivers/pci/controller/dwc/Makefile | 1 +
drivers/pci/controller/dwc/pcie-tegra194.c | 1632 ++++++++++++++++++++
3 files changed, 1643 insertions(+)
create mode 100644 drivers/pci/controller/dwc/pcie-tegra194.c
diff --git a/drivers/pci/controller/dwc/Kconfig b/drivers/pci/controller/dwc/Kconfig
index 6ea778ae4877..49475f5c42c3 100644
--- a/drivers/pci/controller/dwc/Kconfig
+++ b/drivers/pci/controller/dwc/Kconfig
@@ -220,6 +220,16 @@ config PCI_MESON
and therefore the driver re-uses the DesignWare core functions to
implement the driver.
+config PCIE_TEGRA194
+ tristate "NVIDIA Tegra194 (and later) PCIe controller"
+ depends on ARCH_TEGRA_194_SOC || COMPILE_TEST
+ depends on PCI_MSI_IRQ_DOMAIN
+ select PCIE_DW_HOST
+ select PHY_TEGRA194_P2U
+ help
+ Say Y here if you want support for DesignWare core based PCIe host
+ controller found in NVIDIA Tegra194 SoC.
+
config PCIE_UNIPHIER
bool "Socionext UniPhier PCIe controllers"
depends on ARCH_UNIPHIER || COMPILE_TEST
diff --git a/drivers/pci/controller/dwc/Makefile b/drivers/pci/controller/dwc/Makefile
index b085dfd4fab7..b30336181d46 100644
--- a/drivers/pci/controller/dwc/Makefile
+++ b/drivers/pci/controller/dwc/Makefile
@@ -15,6 +15,7 @@ obj-$(CONFIG_PCIE_ARTPEC6) += pcie-artpec6.o
obj-$(CONFIG_PCIE_KIRIN) += pcie-kirin.o
obj-$(CONFIG_PCIE_HISI_STB) += pcie-histb.o
obj-$(CONFIG_PCI_MESON) += pci-meson.o
+obj-$(CONFIG_PCIE_TEGRA194) += pcie-tegra194.o
obj-$(CONFIG_PCIE_UNIPHIER) += pcie-uniphier.o
# The following drivers are for devices that use the generic ACPI
diff --git a/drivers/pci/controller/dwc/pcie-tegra194.c b/drivers/pci/controller/dwc/pcie-tegra194.c
new file mode 100644
index 000000000000..189779edd976
--- /dev/null
+++ b/drivers/pci/controller/dwc/pcie-tegra194.c
@@ -0,0 +1,1632 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * PCIe host controller driver for Tegra194 SoC
+ *
+ * Copyright (C) 2019 NVIDIA Corporation.
+ *
+ * Author: Vidya Sagar <vidyas@nvidia.com>
+ */
+
+#include <linux/clk.h>
+#include <linux/debugfs.h>
+#include <linux/delay.h>
+#include <linux/gpio.h>
+#include <linux/interrupt.h>
+#include <linux/iopoll.h>
+#include <linux/kernel.h>
+#include <linux/kfifo.h>
+#include <linux/kthread.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/of_gpio.h>
+#include <linux/of_irq.h>
+#include <linux/of_pci.h>
+#include <linux/pci.h>
+#include <linux/pci-aspm.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/random.h>
+#include <linux/reset.h>
+#include <linux/resource.h>
+#include <linux/types.h>
+#include "pcie-designware.h"
+#include <soc/tegra/bpmp.h>
+#include <soc/tegra/bpmp-abi.h>
+#include "../../pci.h"
+
+#define APPL_PINMUX 0x0
+#define APPL_PINMUX_PEX_RST BIT(0)
+#define APPL_PINMUX_CLKREQ_OVERRIDE_EN BIT(2)
+#define APPL_PINMUX_CLKREQ_OVERRIDE BIT(3)
+#define APPL_PINMUX_CLK_OUTPUT_IN_OVERRIDE_EN BIT(4)
+#define APPL_PINMUX_CLK_OUTPUT_IN_OVERRIDE BIT(5)
+#define APPL_PINMUX_CLKREQ_OUT_OVRD_EN BIT(9)
+#define APPL_PINMUX_CLKREQ_OUT_OVRD BIT(10)
+
+#define APPL_CTRL 0x4
+#define APPL_CTRL_SYS_PRE_DET_STATE BIT(6)
+#define APPL_CTRL_LTSSM_EN BIT(7)
+#define APPL_CTRL_HW_HOT_RST_EN BIT(20)
+#define APPL_CTRL_HW_HOT_RST_MODE_MASK GENMASK(1, 0)
+#define APPL_CTRL_HW_HOT_RST_MODE_SHIFT 22
+#define APPL_CTRL_HW_HOT_RST_MODE_IMDT_RST 0x1
+
+#define APPL_INTR_EN_L0_0 0x8
+#define APPL_INTR_EN_L0_0_LINK_STATE_INT_EN BIT(0)
+#define APPL_INTR_EN_L0_0_MSI_RCV_INT_EN BIT(4)
+#define APPL_INTR_EN_L0_0_INT_INT_EN BIT(8)
+#define APPL_INTR_EN_L0_0_CDM_REG_CHK_INT_EN BIT(19)
+#define APPL_INTR_EN_L0_0_SYS_INTR_EN BIT(30)
+#define APPL_INTR_EN_L0_0_SYS_MSI_INTR_EN BIT(31)
+
+#define APPL_INTR_STATUS_L0 0xC
+#define APPL_INTR_STATUS_L0_LINK_STATE_INT BIT(0)
+#define APPL_INTR_STATUS_L0_INT_INT BIT(8)
+#define APPL_INTR_STATUS_L0_CDM_REG_CHK_INT BIT(18)
+
+#define APPL_INTR_EN_L1_0_0 0x1C
+#define APPL_INTR_EN_L1_0_0_LINK_REQ_RST_NOT_INT_EN BIT(1)
+
+#define APPL_INTR_STATUS_L1_0_0 0x20
+#define APPL_INTR_STATUS_L1_0_0_LINK_REQ_RST_NOT_CHGED BIT(1)
+
+#define APPL_INTR_STATUS_L1_1 0x2C
+#define APPL_INTR_STATUS_L1_2 0x30
+#define APPL_INTR_STATUS_L1_3 0x34
+#define APPL_INTR_STATUS_L1_6 0x3C
+#define APPL_INTR_STATUS_L1_7 0x40
+
+#define APPL_INTR_EN_L1_8_0 0x44
+#define APPL_INTR_EN_L1_8_BW_MGT_INT_EN BIT(2)
+#define APPL_INTR_EN_L1_8_AUTO_BW_INT_EN BIT(3)
+#define APPL_INTR_EN_L1_8_INTX_EN BIT(11)
+#define APPL_INTR_EN_L1_8_AER_INT_EN BIT(15)
+
+#define APPL_INTR_STATUS_L1_8_0 0x4C
+#define APPL_INTR_STATUS_L1_8_0_EDMA_INT_MASK GENMASK(11, 6)
+#define APPL_INTR_STATUS_L1_8_0_BW_MGT_INT_STS BIT(2)
+#define APPL_INTR_STATUS_L1_8_0_AUTO_BW_INT_STS BIT(3)
+
+#define APPL_INTR_STATUS_L1_9 0x54
+#define APPL_INTR_STATUS_L1_10 0x58
+#define APPL_INTR_STATUS_L1_11 0x64
+#define APPL_INTR_STATUS_L1_13 0x74
+#define APPL_INTR_STATUS_L1_14 0x78
+#define APPL_INTR_STATUS_L1_15 0x7C
+#define APPL_INTR_STATUS_L1_17 0x88
+
+#define APPL_INTR_EN_L1_18 0x90
+#define APPL_INTR_EN_L1_18_CDM_REG_CHK_CMPLT BIT(2)
+#define APPL_INTR_EN_L1_18_CDM_REG_CHK_CMP_ERR BIT(1)
+#define APPL_INTR_EN_L1_18_CDM_REG_CHK_LOGIC_ERR BIT(0)
+
+#define APPL_INTR_STATUS_L1_18 0x94
+#define APPL_INTR_STATUS_L1_18_CDM_REG_CHK_CMPLT BIT(2)
+#define APPL_INTR_STATUS_L1_18_CDM_REG_CHK_CMP_ERR BIT(1)
+#define APPL_INTR_STATUS_L1_18_CDM_REG_CHK_LOGIC_ERR BIT(0)
+
+#define APPL_MSI_CTRL_2 0xB0
+
+#define APPL_LTR_MSG_1 0xC4
+#define LTR_MSG_REQ BIT(15)
+#define LTR_MST_NO_SNOOP_SHIFT 16
+
+#define APPL_LTR_MSG_2 0xC8
+#define APPL_LTR_MSG_2_LTR_MSG_REQ_STATE BIT(3)
+
+#define APPL_LINK_STATUS 0xCC
+#define APPL_LINK_STATUS_RDLH_LINK_UP BIT(0)
+
+#define APPL_DEBUG 0xD0
+#define APPL_DEBUG_PM_LINKST_IN_L2_LAT BIT(21)
+#define APPL_DEBUG_PM_LINKST_IN_L0 0x11
+#define APPL_DEBUG_LTSSM_STATE_MASK GENMASK(8, 3)
+#define APPL_DEBUG_LTSSM_STATE_SHIFT 3
+#define LTSSM_STATE_PRE_DETECT 5
+
+#define APPL_RADM_STATUS 0xE4
+#define APPL_PM_XMT_TURNOFF_STATE BIT(0)
+
+#define APPL_DM_TYPE 0x100
+#define APPL_DM_TYPE_MASK GENMASK(3, 0)
+#define APPL_DM_TYPE_RP 0x4
+#define APPL_DM_TYPE_EP 0x0
+
+#define APPL_CFG_BASE_ADDR 0x104
+#define APPL_CFG_BASE_ADDR_MASK GENMASK(31, 12)
+
+#define APPL_CFG_IATU_DMA_BASE_ADDR 0x108
+#define APPL_CFG_IATU_DMA_BASE_ADDR_MASK GENMASK(31, 18)
+
+#define APPL_CFG_MISC 0x110
+#define APPL_CFG_MISC_SLV_EP_MODE BIT(14)
+#define APPL_CFG_MISC_ARCACHE_MASK GENMASK(13, 10)
+#define APPL_CFG_MISC_ARCACHE_SHIFT 10
+#define APPL_CFG_MISC_ARCACHE_VAL 3
+
+#define APPL_CFG_SLCG_OVERRIDE 0x114
+#define APPL_CFG_SLCG_OVERRIDE_SLCG_EN_MASTER BIT(0)
+
+#define APPL_CAR_RESET_OVRD 0x12C
+#define APPL_CAR_RESET_OVRD_CYA_OVERRIDE_CORE_RST_N BIT(0)
+
+#define IO_BASE_IO_DECODE BIT(0)
+#define IO_BASE_IO_DECODE_BIT8 BIT(8)
+
+#define CFG_PREF_MEM_LIMIT_BASE_MEM_DECODE BIT(0)
+#define CFG_PREF_MEM_LIMIT_BASE_MEM_LIMIT_DECODE BIT(16)
+
+#define CFG_TIMER_CTRL_MAX_FUNC_NUM_OFF 0x718
+#define CFG_TIMER_CTRL_ACK_NAK_SHIFT (19)
+
+#define EVENT_COUNTER_ALL_CLEAR 0x3
+#define EVENT_COUNTER_ENABLE_ALL 0x7
+#define EVENT_COUNTER_ENABLE_SHIFT 2
+#define EVENT_COUNTER_EVENT_SEL_MASK GENMASK(7, 0)
+#define EVENT_COUNTER_EVENT_SEL_SHIFT 16
+#define EVENT_COUNTER_EVENT_Tx_L0S 0x2
+#define EVENT_COUNTER_EVENT_Rx_L0S 0x3
+#define EVENT_COUNTER_EVENT_L1 0x5
+#define EVENT_COUNTER_EVENT_L1_1 0x7
+#define EVENT_COUNTER_EVENT_L1_2 0x8
+#define EVENT_COUNTER_GROUP_SEL_SHIFT 24
+#define EVENT_COUNTER_GROUP_5 0x5
+
+#define PORT_LOGIC_ACK_F_ASPM_CTRL 0x70C
+#define ENTER_ASPM BIT(30)
+#define L0S_ENTRANCE_LAT_SHIFT 24
+#define L0S_ENTRANCE_LAT_MASK GENMASK(26, 24)
+#define L1_ENTRANCE_LAT_SHIFT 27
+#define L1_ENTRANCE_LAT_MASK GENMASK(29, 27)
+#define N_FTS_SHIFT 8
+#define N_FTS_MASK GENMASK(7, 0)
+#define N_FTS_VAL 52
+
+#define PORT_LOGIC_GEN2_CTRL 0x80C
+#define PORT_LOGIC_GEN2_CTRL_DIRECT_SPEED_CHANGE BIT(17)
+#define FTS_MASK GENMASK(7, 0)
+#define FTS_VAL 52
+
+#define PORT_LOGIC_MSI_CTRL_INT_0_EN 0x828
+
+#define GEN3_EQ_CONTROL_OFF 0x8a8
+#define GEN3_EQ_CONTROL_OFF_PSET_REQ_VEC_SHIFT 8
+#define GEN3_EQ_CONTROL_OFF_PSET_REQ_VEC_MASK GENMASK(23, 8)
+#define GEN3_EQ_CONTROL_OFF_FB_MODE_MASK GENMASK(3, 0)
+
+#define GEN3_RELATED_OFF 0x890
+#define GEN3_RELATED_OFF_GEN3_ZRXDC_NONCOMPL BIT(0)
+#define GEN3_RELATED_OFF_GEN3_EQ_DISABLE BIT(16)
+#define GEN3_RELATED_OFF_RATE_SHADOW_SEL_SHIFT 24
+#define GEN3_RELATED_OFF_RATE_SHADOW_SEL_MASK GENMASK(25, 24)
+
+#define PORT_LOGIC_AMBA_ERROR_RESPONSE_DEFAULT 0x8D0
+#define AMBA_ERROR_RESPONSE_CRS_SHIFT 3
+#define AMBA_ERROR_RESPONSE_CRS_MASK GENMASK(1, 0)
+#define AMBA_ERROR_RESPONSE_CRS_OKAY 0
+#define AMBA_ERROR_RESPONSE_CRS_OKAY_FFFFFFFF 1
+#define AMBA_ERROR_RESPONSE_CRS_OKAY_FFFF0001 2
+
+#define PORT_LOGIC_MSIX_DOORBELL 0x948
+
+#define CAP_SPCIE_CAP_OFF 0x154
+#define CAP_SPCIE_CAP_OFF_DSP_TX_PRESET0_MASK GENMASK(3, 0)
+#define CAP_SPCIE_CAP_OFF_USP_TX_PRESET0_MASK GENMASK(11, 8)
+#define CAP_SPCIE_CAP_OFF_USP_TX_PRESET0_SHIFT 8
+
+#define PME_ACK_TIMEOUT 10000
+
+#define LTSSM_TIMEOUT 50000 /* 50ms */
+
+#define GEN3_GEN4_EQ_PRESET_INIT 5
+
+#define GEN1_CORE_CLK_FREQ 62500000
+#define GEN2_CORE_CLK_FREQ 125000000
+#define GEN3_CORE_CLK_FREQ 250000000
+#define GEN4_CORE_CLK_FREQ 500000000
+
+static const unsigned int pcie_gen_freq[] = {
+ GEN1_CORE_CLK_FREQ,
+ GEN2_CORE_CLK_FREQ,
+ GEN3_CORE_CLK_FREQ,
+ GEN4_CORE_CLK_FREQ
+};
+
+static const u32 event_cntr_ctrl_offset[] = {
+ 0x1d8,
+ 0x1a8,
+ 0x1a8,
+ 0x1a8,
+ 0x1c4,
+ 0x1d8
+};
+
+static const u32 event_cntr_data_offset[] = {
+ 0x1dc,
+ 0x1ac,
+ 0x1ac,
+ 0x1ac,
+ 0x1c8,
+ 0x1dc
+};
+
+struct tegra_pcie_dw {
+ struct device *dev;
+ struct resource *appl_res;
+ struct resource *dbi_res;
+ struct resource *atu_dma_res;
+ void __iomem *appl_base;
+ struct clk *core_clk;
+ struct reset_control *core_apb_rst;
+ struct reset_control *core_rst;
+ struct dw_pcie pci;
+ enum dw_pcie_device_mode mode;
+ struct tegra_bpmp *bpmp;
+
+ bool supports_clkreq;
+ bool enable_cdm_check;
+ u8 init_link_width;
+ bool link_state;
+ u32 msi_ctrl_int;
+ u32 num_lanes;
+ u32 max_speed;
+ u32 cid;
+ bool update_fc_fixup;
+ u32 cfg_link_cap_l1sub;
+ u32 pcie_cap_base;
+ u32 aspm_cmrt;
+ u32 aspm_pwr_on_t;
+ u32 aspm_l0s_enter_lat;
+
+ struct regulator *pex_ctl_supply;
+
+ unsigned int phy_count;
+ struct phy **phys;
+
+ struct dentry *debugfs;
+};
+
+static inline struct tegra_pcie_dw *to_tegra_pcie(struct dw_pcie *pci)
+{
+ return container_of(pci, struct tegra_pcie_dw, pci);
+}
+
+static inline void appl_writel(struct tegra_pcie_dw *pcie, const u32 value,
+ const u32 reg)
+{
+ writel_relaxed(value, pcie->appl_base + reg);
+}
+
+static inline u32 appl_readl(struct tegra_pcie_dw *pcie, const u32 reg)
+{
+ return readl_relaxed(pcie->appl_base + reg);
+}
+
+struct tegra_pcie_soc {
+ enum dw_pcie_device_mode mode;
+};
+
+static void apply_bad_link_workaround(struct pcie_port *pp)
+{
+ struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
+ struct tegra_pcie_dw *pcie = to_tegra_pcie(pci);
+ u32 current_link_width;
+ u16 val;
+
+ /*
+ * NOTE:- Since this scenario is uncommon and link as such is not
+ * stable anyway, not waiting to confirm if link is really
+ * transitioning to Gen-2 speed
+ */
+ val = dw_pcie_readw_dbi(pci, pcie->pcie_cap_base + PCI_EXP_LNKSTA);
+ if (val & PCI_EXP_LNKSTA_LBMS) {
+ current_link_width = (val & PCI_EXP_LNKSTA_NLW) >>
+ PCI_EXP_LNKSTA_NLW_SHIFT;
+ if (pcie->init_link_width > current_link_width) {
+ dev_warn(pci->dev, "PCIe link is bad, width reduced\n");
+ val = dw_pcie_readw_dbi(pci, pcie->pcie_cap_base +
+ PCI_EXP_LNKCTL2);
+ val &= ~PCI_EXP_LNKCTL2_TLS;
+ val |= PCI_EXP_LNKCTL2_TLS_2_5GT;
+ dw_pcie_writew_dbi(pci, pcie->pcie_cap_base +
+ PCI_EXP_LNKCTL2, val);
+
+ val = dw_pcie_readw_dbi(pci, pcie->pcie_cap_base +
+ PCI_EXP_LNKCTL);
+ val |= PCI_EXP_LNKCTL_RL;
+ dw_pcie_writew_dbi(pci, pcie->pcie_cap_base +
+ PCI_EXP_LNKCTL, val);
+ }
+ }
+}
+
+static irqreturn_t tegra_pcie_rp_irq_handler(struct tegra_pcie_dw *pcie)
+{
+ struct dw_pcie *pci = &pcie->pci;
+ struct pcie_port *pp = &pci->pp;
+ u32 val, tmp;
+ u16 val_w;
+
+ val = appl_readl(pcie, APPL_INTR_STATUS_L0);
+ if (val & APPL_INTR_STATUS_L0_LINK_STATE_INT) {
+ val = appl_readl(pcie, APPL_INTR_STATUS_L1_0_0);
+ if (val & APPL_INTR_STATUS_L1_0_0_LINK_REQ_RST_NOT_CHGED) {
+ appl_writel(pcie, val, APPL_INTR_STATUS_L1_0_0);
+
+ /* SBR & Surprise Link Down WAR */
+ val = appl_readl(pcie, APPL_CAR_RESET_OVRD);
+ val &= ~APPL_CAR_RESET_OVRD_CYA_OVERRIDE_CORE_RST_N;
+ appl_writel(pcie, val, APPL_CAR_RESET_OVRD);
+ udelay(1);
+ val = appl_readl(pcie, APPL_CAR_RESET_OVRD);
+ val |= APPL_CAR_RESET_OVRD_CYA_OVERRIDE_CORE_RST_N;
+ appl_writel(pcie, val, APPL_CAR_RESET_OVRD);
+
+ val = dw_pcie_readl_dbi(pci, PORT_LOGIC_GEN2_CTRL);
+ val |= PORT_LOGIC_GEN2_CTRL_DIRECT_SPEED_CHANGE;
+ dw_pcie_writel_dbi(pci, PORT_LOGIC_GEN2_CTRL, val);
+ }
+ }
+
+ if (val & APPL_INTR_STATUS_L0_INT_INT) {
+ val = appl_readl(pcie, APPL_INTR_STATUS_L1_8_0);
+ if (val & APPL_INTR_STATUS_L1_8_0_AUTO_BW_INT_STS) {
+ appl_writel(pcie,
+ APPL_INTR_STATUS_L1_8_0_AUTO_BW_INT_STS,
+ APPL_INTR_STATUS_L1_8_0);
+ apply_bad_link_workaround(pp);
+ }
+ if (val & APPL_INTR_STATUS_L1_8_0_BW_MGT_INT_STS) {
+ appl_writel(pcie,
+ APPL_INTR_STATUS_L1_8_0_BW_MGT_INT_STS,
+ APPL_INTR_STATUS_L1_8_0);
+
+ val_w = dw_pcie_readw_dbi(pci, pcie->pcie_cap_base +
+ PCI_EXP_LNKSTA);
+ dev_dbg(pci->dev, "Link Speed : Gen-%u\n", val_w &
+ PCI_EXP_LNKSTA_CLS);
+ }
+ }
+
+ val = appl_readl(pcie, APPL_INTR_STATUS_L0);
+ if (val & APPL_INTR_STATUS_L0_CDM_REG_CHK_INT) {
+ val = appl_readl(pcie, APPL_INTR_STATUS_L1_18);
+ tmp = dw_pcie_readl_dbi(pci, PCIE_PL_CHK_REG_CONTROL_STATUS);
+ if (val & APPL_INTR_STATUS_L1_18_CDM_REG_CHK_CMPLT) {
+ dev_info(pci->dev, "CDM check complete\n");
+ tmp |= PCIE_PL_CHK_REG_CHK_REG_COMPLETE;
+ }
+ if (val & APPL_INTR_STATUS_L1_18_CDM_REG_CHK_CMP_ERR) {
+ dev_err(pci->dev, "CDM comparison mismatch\n");
+ tmp |= PCIE_PL_CHK_REG_CHK_REG_COMPARISON_ERROR;
+ }
+ if (val & APPL_INTR_STATUS_L1_18_CDM_REG_CHK_LOGIC_ERR) {
+ dev_err(pci->dev, "CDM Logic error\n");
+ tmp |= PCIE_PL_CHK_REG_CHK_REG_LOGIC_ERROR;
+ }
+ dw_pcie_writel_dbi(pci, PCIE_PL_CHK_REG_CONTROL_STATUS, tmp);
+ tmp = dw_pcie_readl_dbi(pci, PCIE_PL_CHK_REG_ERR_ADDR);
+ dev_err(pci->dev, "CDM Error Address Offset = 0x%08X\n", tmp);
+ }
+
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t tegra_pcie_irq_handler(int irq, void *arg)
+{
+ struct tegra_pcie_dw *pcie = arg;
+
+ if (pcie->mode == DW_PCIE_RC_TYPE)
+ return tegra_pcie_rp_irq_handler(pcie);
+
+ return IRQ_NONE;
+}
+
+static int tegra_pcie_dw_rd_own_conf(struct pcie_port *pp, int where, int size,
+ u32 *val)
+{
+ struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
+
+ /*
+ * This is an endpoint mode specific register happen to appear even
+ * when controller is operating in root port mode and system hangs
+ * when it is accessed with link being in ASPM-L1 state.
+ * So skip accessing it altogether
+ */
+ if (where == PORT_LOGIC_MSIX_DOORBELL) {
+ *val = 0x00000000;
+ return PCIBIOS_SUCCESSFUL;
+ }
+
+ return dw_pcie_read(pci->dbi_base + where, size, val);
+}
+
+static int tegra_pcie_dw_wr_own_conf(struct pcie_port *pp, int where, int size,
+ u32 val)
+{
+ struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
+
+ /*
+ * This is an endpoint mode specific register happen to appear even
+ * when controller is operating in root port mode and system hangs
+ * when it is accessed with link being in ASPM-L1 state.
+ * So skip accessing it altogether
+ */
+ if (where == PORT_LOGIC_MSIX_DOORBELL)
+ return PCIBIOS_SUCCESSFUL;
+
+ return dw_pcie_write(pci->dbi_base + where, size, val);
+}
+
+#if defined(CONFIG_PCIEASPM)
+static void disable_aspm_l11(struct tegra_pcie_dw *pcie)
+{
+ u32 val;
+
+ val = dw_pcie_readl_dbi(&pcie->pci, pcie->cfg_link_cap_l1sub);
+ val &= ~PCI_L1SS_CAP_ASPM_L1_1;
+ dw_pcie_writel_dbi(&pcie->pci, pcie->cfg_link_cap_l1sub, val);
+}
+
+static void disable_aspm_l12(struct tegra_pcie_dw *pcie)
+{
+ u32 val;
+
+ val = dw_pcie_readl_dbi(&pcie->pci, pcie->cfg_link_cap_l1sub);
+ val &= ~PCI_L1SS_CAP_ASPM_L1_2;
+ dw_pcie_writel_dbi(&pcie->pci, pcie->cfg_link_cap_l1sub, val);
+}
+
+static inline u32 event_counter_prog(struct tegra_pcie_dw *pcie, u32 event)
+{
+ u32 val;
+
+ val = dw_pcie_readl_dbi(&pcie->pci, event_cntr_ctrl_offset[pcie->cid]);
+ val &= ~(EVENT_COUNTER_EVENT_SEL_MASK << EVENT_COUNTER_EVENT_SEL_SHIFT);
+ val |= EVENT_COUNTER_GROUP_5 << EVENT_COUNTER_GROUP_SEL_SHIFT;
+ val |= event << EVENT_COUNTER_EVENT_SEL_SHIFT;
+ val |= EVENT_COUNTER_ENABLE_ALL << EVENT_COUNTER_ENABLE_SHIFT;
+ dw_pcie_writel_dbi(&pcie->pci, event_cntr_ctrl_offset[pcie->cid], val);
+ val = dw_pcie_readl_dbi(&pcie->pci, event_cntr_data_offset[pcie->cid]);
+ return val;
+}
+
+static int aspm_state_cnt(struct seq_file *s, void *data)
+{
+ struct tegra_pcie_dw *pcie = (struct tegra_pcie_dw *)
+ dev_get_drvdata(s->private);
+ u32 val;
+
+ seq_printf(s, "Tx L0s entry count : %u\n",
+ event_counter_prog(pcie, EVENT_COUNTER_EVENT_Tx_L0S));
+
+ seq_printf(s, "Rx L0s entry count : %u\n",
+ event_counter_prog(pcie, EVENT_COUNTER_EVENT_Rx_L0S));
+
+ seq_printf(s, "Link L1 entry count : %u\n",
+ event_counter_prog(pcie, EVENT_COUNTER_EVENT_L1));
+
+ seq_printf(s, "Link L1.1 entry count : %u\n",
+ event_counter_prog(pcie, EVENT_COUNTER_EVENT_L1_1));
+
+ seq_printf(s, "Link L1.2 entry count : %u\n",
+ event_counter_prog(pcie, EVENT_COUNTER_EVENT_L1_2));
+
+ /* Clear all counters */
+ dw_pcie_writel_dbi(&pcie->pci, event_cntr_ctrl_offset[pcie->cid],
+ EVENT_COUNTER_ALL_CLEAR);
+
+ /* Re-enable counting */
+ val = EVENT_COUNTER_ENABLE_ALL << EVENT_COUNTER_ENABLE_SHIFT;
+ val |= EVENT_COUNTER_GROUP_5 << EVENT_COUNTER_GROUP_SEL_SHIFT;
+ dw_pcie_writel_dbi(&pcie->pci, event_cntr_ctrl_offset[pcie->cid], val);
+
+ return 0;
+}
+#endif
+
+static int init_debugfs(struct tegra_pcie_dw *pcie)
+{
+#if defined(CONFIG_PCIEASPM)
+ struct dentry *d;
+
+ d = debugfs_create_devm_seqfile(pcie->dev, "aspm_state_cnt",
+ pcie->debugfs, aspm_state_cnt);
+ if (IS_ERR_OR_NULL(d))
+ dev_err(pcie->dev,
+ "Failed to create debugfs file \"aspm_state_cnt\"\n");
+#endif
+ return 0;
+}
+
+static void tegra_pcie_enable_system_interrupts(struct pcie_port *pp)
+{
+ struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
+ struct tegra_pcie_dw *pcie = to_tegra_pcie(pci);
+ u32 val;
+ u16 val_w;
+
+ val = appl_readl(pcie, APPL_INTR_EN_L0_0);
+ val |= APPL_INTR_EN_L0_0_LINK_STATE_INT_EN;
+ appl_writel(pcie, val, APPL_INTR_EN_L0_0);
+
+ val = appl_readl(pcie, APPL_INTR_EN_L1_0_0);
+ val |= APPL_INTR_EN_L1_0_0_LINK_REQ_RST_NOT_INT_EN;
+ appl_writel(pcie, val, APPL_INTR_EN_L1_0_0);
+
+ if (pcie->enable_cdm_check) {
+ val = appl_readl(pcie, APPL_INTR_EN_L0_0);
+ val |= APPL_INTR_EN_L0_0_CDM_REG_CHK_INT_EN;
+ appl_writel(pcie, val, APPL_INTR_EN_L0_0);
+
+ val = appl_readl(pcie, APPL_INTR_EN_L1_18);
+ val |= APPL_INTR_EN_L1_18_CDM_REG_CHK_CMP_ERR;
+ val |= APPL_INTR_EN_L1_18_CDM_REG_CHK_LOGIC_ERR;
+ appl_writel(pcie, val, APPL_INTR_EN_L1_18);
+ }
+
+ val_w = dw_pcie_readw_dbi(&pcie->pci, pcie->pcie_cap_base +
+ PCI_EXP_LNKSTA);
+ pcie->init_link_width = (val_w & PCI_EXP_LNKSTA_NLW) >>
+ PCI_EXP_LNKSTA_NLW_SHIFT;
+
+ val_w = dw_pcie_readw_dbi(&pcie->pci, pcie->pcie_cap_base +
+ PCI_EXP_LNKCTL);
+ val_w |= PCI_EXP_LNKCTL_LBMIE;
+ dw_pcie_writew_dbi(&pcie->pci, pcie->pcie_cap_base + PCI_EXP_LNKCTL,
+ val_w);
+}
+
+static void tegra_pcie_enable_legacy_interrupts(struct pcie_port *pp)
+{
+ struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
+ struct tegra_pcie_dw *pcie = to_tegra_pcie(pci);
+ u32 val;
+
+ /* Enable legacy interrupt generation */
+ val = appl_readl(pcie, APPL_INTR_EN_L0_0);
+ val |= APPL_INTR_EN_L0_0_SYS_INTR_EN;
+ val |= APPL_INTR_EN_L0_0_INT_INT_EN;
+ appl_writel(pcie, val, APPL_INTR_EN_L0_0);
+
+ val = appl_readl(pcie, APPL_INTR_EN_L1_8_0);
+ val |= APPL_INTR_EN_L1_8_INTX_EN;
+ val |= APPL_INTR_EN_L1_8_AUTO_BW_INT_EN;
+ val |= APPL_INTR_EN_L1_8_BW_MGT_INT_EN;
+ if (IS_ENABLED(CONFIG_PCIEAER))
+ val |= APPL_INTR_EN_L1_8_AER_INT_EN;
+ appl_writel(pcie, val, APPL_INTR_EN_L1_8_0);
+}
+
+static void tegra_pcie_enable_msi_interrupts(struct pcie_port *pp)
+{
+ struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
+ struct tegra_pcie_dw *pcie = to_tegra_pcie(pci);
+ u32 val;
+
+ dw_pcie_msi_init(pp);
+
+ /* Enable MSI interrupt generation */
+ val = appl_readl(pcie, APPL_INTR_EN_L0_0);
+ val |= APPL_INTR_EN_L0_0_SYS_MSI_INTR_EN;
+ val |= APPL_INTR_EN_L0_0_MSI_RCV_INT_EN;
+ appl_writel(pcie, val, APPL_INTR_EN_L0_0);
+}
+
+static void tegra_pcie_enable_interrupts(struct pcie_port *pp)
+{
+ struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
+ struct tegra_pcie_dw *pcie = to_tegra_pcie(pci);
+
+ /* Clear interrupt statuses before enabling interrupts */
+ appl_writel(pcie, 0xFFFFFFFF, APPL_INTR_STATUS_L0);
+ appl_writel(pcie, 0xFFFFFFFF, APPL_INTR_STATUS_L1_0_0);
+ appl_writel(pcie, 0xFFFFFFFF, APPL_INTR_STATUS_L1_1);
+ appl_writel(pcie, 0xFFFFFFFF, APPL_INTR_STATUS_L1_2);
+ appl_writel(pcie, 0xFFFFFFFF, APPL_INTR_STATUS_L1_3);
+ appl_writel(pcie, 0xFFFFFFFF, APPL_INTR_STATUS_L1_6);
+ appl_writel(pcie, 0xFFFFFFFF, APPL_INTR_STATUS_L1_7);
+ appl_writel(pcie, 0xFFFFFFFF, APPL_INTR_STATUS_L1_8_0);
+ appl_writel(pcie, 0xFFFFFFFF, APPL_INTR_STATUS_L1_9);
+ appl_writel(pcie, 0xFFFFFFFF, APPL_INTR_STATUS_L1_10);
+ appl_writel(pcie, 0xFFFFFFFF, APPL_INTR_STATUS_L1_11);
+ appl_writel(pcie, 0xFFFFFFFF, APPL_INTR_STATUS_L1_13);
+ appl_writel(pcie, 0xFFFFFFFF, APPL_INTR_STATUS_L1_14);
+ appl_writel(pcie, 0xFFFFFFFF, APPL_INTR_STATUS_L1_15);
+ appl_writel(pcie, 0xFFFFFFFF, APPL_INTR_STATUS_L1_17);
+
+ tegra_pcie_enable_system_interrupts(pp);
+ tegra_pcie_enable_legacy_interrupts(pp);
+ if (IS_ENABLED(CONFIG_PCI_MSI))
+ tegra_pcie_enable_msi_interrupts(pp);
+}
+
+static void config_gen3_gen4_eq_presets(struct tegra_pcie_dw *pcie)
+{
+ struct dw_pcie *pci = &pcie->pci;
+ u32 val, offset, i;
+
+ /* Program init preset */
+ for (i = 0; i < pcie->num_lanes; i++) {
+ dw_pcie_read(pci->dbi_base + CAP_SPCIE_CAP_OFF
+ + (i * 2), 2, &val);
+ val &= ~CAP_SPCIE_CAP_OFF_DSP_TX_PRESET0_MASK;
+ val |= GEN3_GEN4_EQ_PRESET_INIT;
+ val &= ~CAP_SPCIE_CAP_OFF_USP_TX_PRESET0_MASK;
+ val |= (GEN3_GEN4_EQ_PRESET_INIT <<
+ CAP_SPCIE_CAP_OFF_USP_TX_PRESET0_SHIFT);
+ dw_pcie_write(pci->dbi_base + CAP_SPCIE_CAP_OFF
+ + (i * 2), 2, val);
+
+ offset = dw_pcie_find_ext_capability(pci,
+ PCI_EXT_CAP_ID_PL_16GT) +
+ PCI_PL_16GT_LE_CTRL;
+ dw_pcie_read(pci->dbi_base + offset + i, 1, &val);
+ val &= ~PCI_PL_16GT_LE_CTRL_DSP_TX_PRESET_MASK;
+ val |= GEN3_GEN4_EQ_PRESET_INIT;
+ val &= ~PCI_PL_16GT_LE_CTRL_USP_TX_PRESET_MASK;
+ val |= (GEN3_GEN4_EQ_PRESET_INIT <<
+ PCI_PL_16GT_LE_CTRL_USP_TX_PRESET_SHIFT);
+ dw_pcie_write(pci->dbi_base + offset + i, 1, val);
+ }
+
+ val = dw_pcie_readl_dbi(pci, GEN3_RELATED_OFF);
+ val &= ~GEN3_RELATED_OFF_RATE_SHADOW_SEL_MASK;
+ dw_pcie_writel_dbi(pci, GEN3_RELATED_OFF, val);
+
+ val = dw_pcie_readl_dbi(pci, GEN3_EQ_CONTROL_OFF);
+ val &= ~GEN3_EQ_CONTROL_OFF_PSET_REQ_VEC_MASK;
+ val |= (0x3ff << GEN3_EQ_CONTROL_OFF_PSET_REQ_VEC_SHIFT);
+ val &= ~GEN3_EQ_CONTROL_OFF_FB_MODE_MASK;
+ dw_pcie_writel_dbi(pci, GEN3_EQ_CONTROL_OFF, val);
+
+ val = dw_pcie_readl_dbi(pci, GEN3_RELATED_OFF);
+ val &= ~GEN3_RELATED_OFF_RATE_SHADOW_SEL_MASK;
+ val |= (0x1 << GEN3_RELATED_OFF_RATE_SHADOW_SEL_SHIFT);
+ dw_pcie_writel_dbi(pci, GEN3_RELATED_OFF, val);
+
+ val = dw_pcie_readl_dbi(pci, GEN3_EQ_CONTROL_OFF);
+ val &= ~GEN3_EQ_CONTROL_OFF_PSET_REQ_VEC_MASK;
+ val |= (0x360 << GEN3_EQ_CONTROL_OFF_PSET_REQ_VEC_SHIFT);
+ val &= ~GEN3_EQ_CONTROL_OFF_FB_MODE_MASK;
+ dw_pcie_writel_dbi(pci, GEN3_EQ_CONTROL_OFF, val);
+
+ val = dw_pcie_readl_dbi(pci, GEN3_RELATED_OFF);
+ val &= ~GEN3_RELATED_OFF_RATE_SHADOW_SEL_MASK;
+ dw_pcie_writel_dbi(pci, GEN3_RELATED_OFF, val);
+}
+
+static int tegra_pcie_dw_host_init(struct pcie_port *pp)
+{
+ struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
+ struct tegra_pcie_dw *pcie = to_tegra_pcie(pci);
+ u32 val, tmp, offset, speed;
+ unsigned int count;
+ u16 val_w;
+
+core_init:
+ count = 200;
+#if defined(CONFIG_PCIEASPM)
+ offset = dw_pcie_find_ext_capability(pci, PCI_EXT_CAP_ID_L1SS);
+ pcie->cfg_link_cap_l1sub = offset + PCI_L1SS_CAP;
+#endif
+ val = dw_pcie_readl_dbi(pci, PCI_IO_BASE);
+ val &= ~(IO_BASE_IO_DECODE | IO_BASE_IO_DECODE_BIT8);
+ dw_pcie_writel_dbi(pci, PCI_IO_BASE, val);
+
+ val = dw_pcie_readl_dbi(pci, PCI_PREF_MEMORY_BASE);
+ val |= CFG_PREF_MEM_LIMIT_BASE_MEM_DECODE;
+ val |= CFG_PREF_MEM_LIMIT_BASE_MEM_LIMIT_DECODE;
+ dw_pcie_writel_dbi(pci, PCI_PREF_MEMORY_BASE, val);
+
+ dw_pcie_writel_dbi(pci, PCI_BASE_ADDRESS_0, 0);
+
+ /* Configure FTS */
+ val = dw_pcie_readl_dbi(pci, PORT_LOGIC_ACK_F_ASPM_CTRL);
+ val &= ~(N_FTS_MASK << N_FTS_SHIFT);
+ val |= N_FTS_VAL << N_FTS_SHIFT;
+ dw_pcie_writel_dbi(pci, PORT_LOGIC_ACK_F_ASPM_CTRL, val);
+
+ val = dw_pcie_readl_dbi(pci, PORT_LOGIC_GEN2_CTRL);
+ val &= ~FTS_MASK;
+ val |= FTS_VAL;
+ dw_pcie_writel_dbi(pci, PORT_LOGIC_GEN2_CTRL, val);
+
+ /* Enable as 0xFFFF0001 response for CRS */
+ val = dw_pcie_readl_dbi(pci, PORT_LOGIC_AMBA_ERROR_RESPONSE_DEFAULT);
+ val &= ~(AMBA_ERROR_RESPONSE_CRS_MASK << AMBA_ERROR_RESPONSE_CRS_SHIFT);
+ val |= (AMBA_ERROR_RESPONSE_CRS_OKAY_FFFF0001 <<
+ AMBA_ERROR_RESPONSE_CRS_SHIFT);
+ dw_pcie_writel_dbi(pci, PORT_LOGIC_AMBA_ERROR_RESPONSE_DEFAULT, val);
+
+ /* Configure Max Speed from DT */
+ if (pcie->max_speed && pcie->max_speed != -EINVAL) {
+ val = dw_pcie_readl_dbi(pci, pcie->pcie_cap_base +
+ PCI_EXP_LNKCAP);
+ val &= ~PCI_EXP_LNKCAP_SLS;
+ val |= pcie->max_speed;
+ dw_pcie_writel_dbi(pci, pcie->pcie_cap_base + PCI_EXP_LNKCAP,
+ val);
+ }
+
+ /* Configure Max lane width from DT */
+ val = dw_pcie_readl_dbi(pci, pcie->pcie_cap_base + PCI_EXP_LNKCAP);
+ val &= ~PCI_EXP_LNKCAP_MLW;
+ val |= (pcie->num_lanes << PCI_EXP_LNKSTA_NLW_SHIFT);
+ dw_pcie_writel_dbi(pci, pcie->pcie_cap_base + PCI_EXP_LNKCAP, val);
+
+ config_gen3_gen4_eq_presets(pcie);
+
+#if defined(CONFIG_PCIEASPM)
+ /* Enable ASPM counters */
+ val = EVENT_COUNTER_ENABLE_ALL << EVENT_COUNTER_ENABLE_SHIFT;
+ val |= EVENT_COUNTER_GROUP_5 << EVENT_COUNTER_GROUP_SEL_SHIFT;
+ dw_pcie_writel_dbi(pci, event_cntr_ctrl_offset[pcie->cid], val);
+
+ /* Program T_cmrt and T_pwr_on values */
+ val = dw_pcie_readl_dbi(pci, pcie->cfg_link_cap_l1sub);
+ val &= ~(PCI_L1SS_CAP_CM_RESTORE_TIME | PCI_L1SS_CAP_P_PWR_ON_VALUE);
+ val |= (pcie->aspm_cmrt << 8);
+ val |= (pcie->aspm_pwr_on_t << 19);
+ dw_pcie_writel_dbi(pci, pcie->cfg_link_cap_l1sub, val);
+
+ /* Program L0s and L1 entrance latencies */
+ val = dw_pcie_readl_dbi(pci, PORT_LOGIC_ACK_F_ASPM_CTRL);
+ val &= ~L0S_ENTRANCE_LAT_MASK;
+ val |= (pcie->aspm_l0s_enter_lat << L0S_ENTRANCE_LAT_SHIFT);
+ val |= ENTER_ASPM;
+ dw_pcie_writel_dbi(pci, PORT_LOGIC_ACK_F_ASPM_CTRL, val);
+#endif
+ val = dw_pcie_readl_dbi(pci, GEN3_RELATED_OFF);
+ val &= ~GEN3_RELATED_OFF_GEN3_ZRXDC_NONCOMPL;
+ dw_pcie_writel_dbi(pci, GEN3_RELATED_OFF, val);
+
+ if (pcie->update_fc_fixup) {
+ val = dw_pcie_readl_dbi(pci, CFG_TIMER_CTRL_MAX_FUNC_NUM_OFF);
+ val |= 0x1 << CFG_TIMER_CTRL_ACK_NAK_SHIFT;
+ dw_pcie_writel_dbi(pci, CFG_TIMER_CTRL_MAX_FUNC_NUM_OFF, val);
+ }
+
+ dw_pcie_setup_rc(pp);
+
+ clk_set_rate(pcie->core_clk, GEN4_CORE_CLK_FREQ);
+
+ /* Assert RST */
+ val = appl_readl(pcie, APPL_PINMUX);
+ val &= ~APPL_PINMUX_PEX_RST;
+ appl_writel(pcie, val, APPL_PINMUX);
+
+ usleep_range(100, 200);
+
+ /* Enable LTSSM */
+ val = appl_readl(pcie, APPL_CTRL);
+ val |= APPL_CTRL_LTSSM_EN;
+ appl_writel(pcie, val, APPL_CTRL);
+
+ /* De-assert RST */
+ val = appl_readl(pcie, APPL_PINMUX);
+ val |= APPL_PINMUX_PEX_RST;
+ appl_writel(pcie, val, APPL_PINMUX);
+
+ msleep(100);
+
+ val_w = dw_pcie_readw_dbi(pci, pcie->pcie_cap_base + PCI_EXP_LNKSTA);
+ while (!(val_w & PCI_EXP_LNKSTA_DLLLA)) {
+ if (count) {
+ dev_dbg(pci->dev, "Waiting for link up\n");
+ usleep_range(1000, 2000);
+ val_w = dw_pcie_readw_dbi(pci, pcie->pcie_cap_base +
+ PCI_EXP_LNKSTA);
+ count--;
+ continue;
+ }
+
+ val = appl_readl(pcie, APPL_DEBUG);
+ val &= APPL_DEBUG_LTSSM_STATE_MASK;
+ val >>= APPL_DEBUG_LTSSM_STATE_SHIFT;
+ tmp = appl_readl(pcie, APPL_LINK_STATUS);
+ tmp &= APPL_LINK_STATUS_RDLH_LINK_UP;
+ if (!(val == 0x11 && !tmp)) {
+ dev_info(pci->dev, "Link is down\n");
+ return 0;
+ }
+
+ dev_info(pci->dev, "Link is down in DLL");
+ dev_info(pci->dev, "Trying again with DLFE disabled\n");
+ /* Disable LTSSM */
+ val = appl_readl(pcie, APPL_CTRL);
+ val &= ~APPL_CTRL_LTSSM_EN;
+ appl_writel(pcie, val, APPL_CTRL);
+
+ reset_control_assert(pcie->core_rst);
+ reset_control_deassert(pcie->core_rst);
+
+ offset = dw_pcie_find_ext_capability(pci, PCI_EXT_CAP_ID_DLF);
+ val = dw_pcie_readl_dbi(pci, offset + PCI_DLF_CAP);
+ val &= ~PCI_DLF_EXCHANGE_ENABLE;
+ dw_pcie_writel_dbi(pci, offset, val);
+
+ /* Retry now with DLF Exchange disabled */
+ goto core_init;
+ }
+ dev_dbg(pci->dev, "Link is up\n");
+
+ speed = dw_pcie_readw_dbi(pci, pcie->pcie_cap_base + PCI_EXP_LNKSTA) &
+ PCI_EXP_LNKSTA_CLS;
+ clk_set_rate(pcie->core_clk, pcie_gen_freq[speed - 1]);
+
+ tegra_pcie_enable_interrupts(pp);
+
+ return 0;
+}
+
+static int tegra_pcie_dw_link_up(struct dw_pcie *pci)
+{
+ struct tegra_pcie_dw *pcie = to_tegra_pcie(pci);
+ u32 val = dw_pcie_readw_dbi(pci, pcie->pcie_cap_base + PCI_EXP_LNKSTA);
+
+ return !!(val & PCI_EXP_LNKSTA_DLLLA);
+}
+
+static void tegra_pcie_set_msi_vec_num(struct pcie_port *pp)
+{
+ pp->num_vectors = MAX_MSI_IRQS;
+}
+
+static const struct dw_pcie_ops tegra_dw_pcie_ops = {
+ .link_up = tegra_pcie_dw_link_up,
+};
+
+static struct dw_pcie_host_ops tegra_pcie_dw_host_ops = {
+ .rd_own_conf = tegra_pcie_dw_rd_own_conf,
+ .wr_own_conf = tegra_pcie_dw_wr_own_conf,
+ .host_init = tegra_pcie_dw_host_init,
+ .set_num_vectors = tegra_pcie_set_msi_vec_num,
+};
+
+static void tegra_pcie_disable_phy(struct tegra_pcie_dw *pcie)
+{
+ unsigned int phy_count = pcie->phy_count;
+
+ while (phy_count--) {
+ phy_power_off(pcie->phys[phy_count]);
+ phy_exit(pcie->phys[phy_count]);
+ }
+}
+
+static int tegra_pcie_enable_phy(struct tegra_pcie_dw *pcie)
+{
+ unsigned int i;
+ int ret;
+
+ for (i = 0; i < pcie->phy_count; i++) {
+ ret = phy_init(pcie->phys[i]);
+ if (ret < 0)
+ goto phy_power_off;
+
+ ret = phy_power_on(pcie->phys[i]);
+ if (ret < 0)
+ goto phy_exit;
+ }
+
+ return 0;
+
+phy_power_off:
+ while (i--) {
+ phy_power_off(pcie->phys[i]);
+phy_exit:
+ phy_exit(pcie->phys[i]);
+ }
+
+ return ret;
+}
+
+static int tegra_pcie_dw_parse_dt(struct tegra_pcie_dw *pcie)
+{
+ struct device_node *np = pcie->dev->of_node;
+ int ret;
+
+ ret = of_property_read_u32(np, "nvidia,aspm-cmrt-us", &pcie->aspm_cmrt);
+ if (ret < 0) {
+ dev_info(pcie->dev, "Failed to read ASPM T_cmrt: %d\n", ret);
+ return ret;
+ }
+
+ ret = of_property_read_u32(np, "nvidia,aspm-pwr-on-t-us",
+ &pcie->aspm_pwr_on_t);
+ if (ret < 0)
+ dev_info(pcie->dev, "Failed to read ASPM Power On time: %d\n",
+ ret);
+
+ ret = of_property_read_u32(np, "nvidia,aspm-l0s-entrance-latency-us",
+ &pcie->aspm_l0s_enter_lat);
+ if (ret < 0)
+ dev_info(pcie->dev,
+ "Failed to read ASPM L0s Entrance latency: %d\n", ret);
+
+ ret = of_property_read_u32(np, "num-lanes", &pcie->num_lanes);
+ if (ret < 0) {
+ dev_err(pcie->dev, "Failed to read num-lanes: %d\n", ret);
+ return ret;
+ }
+
+ pcie->max_speed = of_pci_get_max_link_speed(np);
+
+ ret = of_property_read_u32_index(np, "nvidia,bpmp", 1, &pcie->cid);
+ if (ret) {
+ dev_err(pcie->dev, "Failed to read Controller-ID: %d\n", ret);
+ return ret;
+ }
+
+ pcie->phy_count = of_property_count_strings(np, "phy-names");
+ if (pcie->phy_count < 0) {
+ dev_err(pcie->dev, "Failed to find PHY entries: %d\n",
+ pcie->phy_count);
+ return pcie->phy_count;
+ }
+
+ if (of_property_read_bool(np, "nvidia,update-fc-fixup"))
+ pcie->update_fc_fixup = true;
+
+ pcie->supports_clkreq =
+ of_property_read_bool(pcie->dev->of_node, "supports-clkreq");
+
+ pcie->enable_cdm_check =
+ of_property_read_bool(np, "snps,enable-cdm-check");
+
+ return 0;
+}
+
+static int tegra_pcie_bpmp_set_ctrl_state(struct tegra_pcie_dw *pcie,
+ bool enable)
+{
+ struct mrq_uphy_response resp;
+ struct tegra_bpmp_message msg;
+ struct mrq_uphy_request req;
+ int err;
+
+ if (pcie->cid == 5)
+ return 0;
+
+ memset(&req, 0, sizeof(req));
+ memset(&resp, 0, sizeof(resp));
+
+ req.cmd = CMD_UPHY_PCIE_CONTROLLER_STATE;
+ req.controller_state.pcie_controller = pcie->cid;
+ req.controller_state.enable = enable;
+
+ memset(&msg, 0, sizeof(msg));
+ msg.mrq = MRQ_UPHY;
+ msg.tx.data = &req;
+ msg.tx.size = sizeof(req);
+ msg.rx.data = &resp;
+ msg.rx.size = sizeof(resp);
+
+ if (irqs_disabled())
+ err = tegra_bpmp_transfer_atomic(pcie->bpmp, &msg);
+ else
+ err = tegra_bpmp_transfer(pcie->bpmp, &msg);
+
+ return err;
+}
+
+static void tegra_pcie_downstream_dev_to_D0(struct tegra_pcie_dw *pcie)
+{
+ struct pcie_port *pp = &pcie->pci.pp;
+ struct pci_dev *pdev;
+ struct pci_bus *child;
+
+ list_for_each_entry(child, &pp->root_bus->children, node) {
+ /* Bring downstream devices to D0 if they are not already in */
+ if (child->parent == pp->root_bus)
+ break;
+ }
+ list_for_each_entry(pdev, &child->devices, bus_list) {
+ if (PCI_SLOT(pdev->devfn) == 0) {
+ if (pci_set_power_state(pdev, PCI_D0))
+ dev_err(pcie->dev,
+ "Failed to transition %s to D0 state\n",
+ dev_name(&pdev->dev));
+ }
+ }
+}
+
+static int tegra_pcie_config_controller(struct tegra_pcie_dw *pcie,
+ bool en_hw_hot_rst)
+{
+ int ret;
+ u32 val;
+
+ ret = tegra_pcie_bpmp_set_ctrl_state(pcie, true);
+ if (ret) {
+ dev_err(pcie->dev,
+ "Failed to enable controller %u: %d\n", pcie->cid, ret);
+ return ret;
+ }
+
+ ret = regulator_enable(pcie->pex_ctl_supply);
+ if (ret < 0) {
+ dev_err(pcie->dev, "Failed to enable regulator: %d\n", ret);
+ goto fail_reg_en;
+ }
+
+ ret = clk_prepare_enable(pcie->core_clk);
+ if (ret) {
+ dev_err(pcie->dev, "Failed to enable core clock: %d\n", ret);
+ goto fail_core_clk;
+ }
+
+ ret = reset_control_deassert(pcie->core_apb_rst);
+ if (ret) {
+ dev_err(pcie->dev, "Failed to deassert core APB reset: %d\n",
+ ret);
+ goto fail_core_apb_rst;
+ }
+
+ if (en_hw_hot_rst) {
+ /* Enable HW_HOT_RST mode */
+ val = appl_readl(pcie, APPL_CTRL);
+ val &= ~(APPL_CTRL_HW_HOT_RST_MODE_MASK <<
+ APPL_CTRL_HW_HOT_RST_MODE_SHIFT);
+ val |= APPL_CTRL_HW_HOT_RST_EN;
+ appl_writel(pcie, val, APPL_CTRL);
+ }
+
+ ret = tegra_pcie_enable_phy(pcie);
+ if (ret) {
+ dev_err(pcie->dev, "Failed to enable PHY: %d\n", ret);
+ goto fail_phy;
+ }
+
+ /* Update CFG base address */
+ appl_writel(pcie, pcie->dbi_res->start & APPL_CFG_BASE_ADDR_MASK,
+ APPL_CFG_BASE_ADDR);
+
+ /* Configure this core for RP mode operation */
+ appl_writel(pcie, APPL_DM_TYPE_RP, APPL_DM_TYPE);
+
+ appl_writel(pcie, 0x0, APPL_CFG_SLCG_OVERRIDE);
+
+ val = appl_readl(pcie, APPL_CTRL);
+ appl_writel(pcie, val | APPL_CTRL_SYS_PRE_DET_STATE, APPL_CTRL);
+
+ val = appl_readl(pcie, APPL_CFG_MISC);
+ val |= (APPL_CFG_MISC_ARCACHE_VAL << APPL_CFG_MISC_ARCACHE_SHIFT);
+ appl_writel(pcie, val, APPL_CFG_MISC);
+
+ if (!pcie->supports_clkreq) {
+ val = appl_readl(pcie, APPL_PINMUX);
+ val |= APPL_PINMUX_CLKREQ_OUT_OVRD_EN;
+ val |= APPL_PINMUX_CLKREQ_OUT_OVRD;
+ appl_writel(pcie, val, APPL_PINMUX);
+ }
+
+ /* Update iATU_DMA base address */
+ appl_writel(pcie,
+ pcie->atu_dma_res->start & APPL_CFG_IATU_DMA_BASE_ADDR_MASK,
+ APPL_CFG_IATU_DMA_BASE_ADDR);
+
+ reset_control_deassert(pcie->core_rst);
+
+ pcie->pcie_cap_base = dw_pcie_find_capability(&pcie->pci,
+ PCI_CAP_ID_EXP);
+
+#if defined(CONFIG_PCIEASPM)
+ /* Disable ASPM-L1SS advertisement as there is no CLKREQ routing */
+ if (!pcie->supports_clkreq) {
+ disable_aspm_l11(pcie);
+ disable_aspm_l12(pcie);
+ }
+#endif
+ return ret;
+
+fail_phy:
+ reset_control_assert(pcie->core_apb_rst);
+fail_core_apb_rst:
+ clk_disable_unprepare(pcie->core_clk);
+fail_core_clk:
+ regulator_disable(pcie->pex_ctl_supply);
+fail_reg_en:
+ tegra_pcie_bpmp_set_ctrl_state(pcie, false);
+
+ return ret;
+}
+
+static int __deinit_controller(struct tegra_pcie_dw *pcie)
+{
+ int ret;
+
+ ret = reset_control_assert(pcie->core_rst);
+ if (ret) {
+ dev_err(pcie->dev, "Failed to assert \"core\" reset: %d\n",
+ ret);
+ return ret;
+ }
+ tegra_pcie_disable_phy(pcie);
+ ret = reset_control_assert(pcie->core_apb_rst);
+ if (ret) {
+ dev_err(pcie->dev, "Failed to assert APB reset: %d\n", ret);
+ return ret;
+ }
+ clk_disable_unprepare(pcie->core_clk);
+ ret = regulator_disable(pcie->pex_ctl_supply);
+ if (ret) {
+ dev_err(pcie->dev, "Failed to disable regulator: %d\n", ret);
+ return ret;
+ }
+ ret = tegra_pcie_bpmp_set_ctrl_state(pcie, false);
+ if (ret) {
+ dev_err(pcie->dev, "Failed to disable controller %d: %d\n",
+ pcie->cid, ret);
+ return ret;
+ }
+ return ret;
+}
+
+static int tegra_pcie_init_controller(struct tegra_pcie_dw *pcie)
+{
+ struct dw_pcie *pci = &pcie->pci;
+ struct pcie_port *pp = &pci->pp;
+ int ret;
+
+ ret = tegra_pcie_config_controller(pcie, false);
+ if (ret < 0)
+ return ret;
+
+ pp->root_bus_nr = -1;
+ pp->ops = &tegra_pcie_dw_host_ops;
+
+ ret = dw_pcie_host_init(pp);
+ if (ret < 0) {
+ dev_err(pcie->dev, "Failed to add PCIe port: %d\n", ret);
+ goto fail_host_init;
+ }
+
+ return 0;
+
+fail_host_init:
+ return __deinit_controller(pcie);
+}
+
+static int tegra_pcie_try_link_l2(struct tegra_pcie_dw *pcie)
+{
+ u32 val;
+
+ if (!tegra_pcie_dw_link_up(&pcie->pci))
+ return 0;
+
+ val = appl_readl(pcie, APPL_RADM_STATUS);
+ val |= APPL_PM_XMT_TURNOFF_STATE;
+ appl_writel(pcie, val, APPL_RADM_STATUS);
+
+ return readl_poll_timeout_atomic(pcie->appl_base + APPL_DEBUG, val,
+ val & APPL_DEBUG_PM_LINKST_IN_L2_LAT,
+ 1, PME_ACK_TIMEOUT);
+}
+
+static void tegra_pcie_dw_pme_turnoff(struct tegra_pcie_dw *pcie)
+{
+ u32 data;
+ int err;
+
+ if (!tegra_pcie_dw_link_up(&pcie->pci)) {
+ dev_dbg(pcie->dev, "PCIe link is not up...!\n");
+ return;
+ }
+
+ if (tegra_pcie_try_link_l2(pcie)) {
+ dev_info(pcie->dev, "Link didn't transition to L2 state\n");
+ /*
+ * TX lane clock freq will reset to Gen1 only if link is in L2
+ * or detect state.
+ * So apply pex_rst to end point to force RP to go into detect
+ * state
+ */
+ data = appl_readl(pcie, APPL_PINMUX);
+ data &= ~APPL_PINMUX_PEX_RST;
+ appl_writel(pcie, data, APPL_PINMUX);
+
+ err = readl_poll_timeout_atomic(pcie->appl_base + APPL_DEBUG,
+ data,
+ ((data &
+ APPL_DEBUG_LTSSM_STATE_MASK) >>
+ APPL_DEBUG_LTSSM_STATE_SHIFT) ==
+ LTSSM_STATE_PRE_DETECT,
+ 1, LTSSM_TIMEOUT);
+ if (err) {
+ dev_info(pcie->dev, "Link didn't go to detect state\n");
+ } else {
+ /* Disable LTSSM after link is in detect state */
+ data = appl_readl(pcie, APPL_CTRL);
+ data &= ~APPL_CTRL_LTSSM_EN;
+ appl_writel(pcie, data, APPL_CTRL);
+ }
+ }
+ /*
+ * DBI registers may not be accessible after this as PLL-E would be
+ * down depending on how CLKREQ is pulled by end point
+ */
+ data = appl_readl(pcie, APPL_PINMUX);
+ data |= (APPL_PINMUX_CLKREQ_OVERRIDE_EN | APPL_PINMUX_CLKREQ_OVERRIDE);
+ /* Cut REFCLK to slot */
+ data |= APPL_PINMUX_CLK_OUTPUT_IN_OVERRIDE_EN;
+ data &= ~APPL_PINMUX_CLK_OUTPUT_IN_OVERRIDE;
+ appl_writel(pcie, data, APPL_PINMUX);
+}
+
+static int tegra_pcie_deinit_controller(struct tegra_pcie_dw *pcie)
+{
+ /*
+ * link doesn't go into L2 state with some of the endpoints with Tegra
+ * if they are not in D0 state. So, need to make sure that immediate
+ * downstream devices are in D0 state before sending PME_TurnOff to put
+ * link into L2 state
+ */
+ tegra_pcie_downstream_dev_to_D0(pcie);
+ dw_pcie_host_deinit(&pcie->pci.pp);
+ tegra_pcie_dw_pme_turnoff(pcie);
+ return __deinit_controller(pcie);
+}
+
+static int tegra_pcie_config_rp(struct tegra_pcie_dw *pcie)
+{
+ struct pcie_port *pp = &pcie->pci.pp;
+ struct device *dev = pcie->dev;
+ char *name;
+ int ret;
+
+ if (IS_ENABLED(CONFIG_PCI_MSI)) {
+ pp->msi_irq = of_irq_get_byname(dev->of_node, "msi");
+ if (!pp->msi_irq) {
+ dev_err(dev, "Failed to get MSI interrupt\n");
+ return -ENODEV;
+ }
+ }
+
+ pm_runtime_enable(dev);
+ ret = pm_runtime_get_sync(dev);
+ if (ret < 0) {
+ dev_err(dev, "Failed to get runtime sync for PCIe dev: %d\n",
+ ret);
+ pm_runtime_disable(dev);
+ return ret;
+ }
+
+ tegra_pcie_init_controller(pcie);
+
+ pcie->link_state = tegra_pcie_dw_link_up(&pcie->pci);
+
+ if (!pcie->link_state) {
+ ret = -ENOMEDIUM;
+ goto fail_host_init;
+ }
+
+ name = devm_kasprintf(dev, GFP_KERNEL, "%pOFP", dev->of_node);
+ if (!name) {
+ ret = -ENOMEM;
+ goto fail_host_init;
+ }
+
+ pcie->debugfs = debugfs_create_dir(name, NULL);
+ if (!pcie->debugfs)
+ dev_err(dev, "Failed to create debugfs\n");
+ else
+ init_debugfs(pcie);
+
+ return ret;
+
+fail_host_init:
+ tegra_pcie_deinit_controller(pcie);
+ pm_runtime_put_sync(dev);
+ pm_runtime_disable(dev);
+ return ret;
+}
+
+static const struct tegra_pcie_soc tegra_pcie_rc_of_data = {
+ .mode = DW_PCIE_RC_TYPE,
+};
+
+static const struct of_device_id tegra_pcie_dw_of_match[] = {
+ {
+ .compatible = "nvidia,tegra194-pcie",
+ .data = &tegra_pcie_rc_of_data,
+ },
+ {},
+};
+MODULE_DEVICE_TABLE(of, tegra_pcie_dw_of_match);
+
+static int tegra_pcie_dw_probe(struct platform_device *pdev)
+{
+ const struct tegra_pcie_soc *data;
+ struct device *dev = &pdev->dev;
+ struct resource *atu_dma_res;
+ struct tegra_pcie_dw *pcie;
+ struct resource *dbi_res;
+ struct pcie_port *pp;
+ struct dw_pcie *pci;
+ struct phy **phys;
+ char *name;
+ int ret;
+ u32 i;
+
+ pcie = devm_kzalloc(dev, sizeof(*pcie), GFP_KERNEL);
+ if (!pcie)
+ return -ENOMEM;
+
+ pci = &pcie->pci;
+ pci->dev = &pdev->dev;
+ pci->ops = &tegra_dw_pcie_ops;
+ pp = &pci->pp;
+ pcie->dev = &pdev->dev;
+
+ data = (struct tegra_pcie_soc *)of_device_get_match_data(dev);
+ if (!data)
+ return -EINVAL;
+ pcie->mode = (enum dw_pcie_device_mode)data->mode;
+
+ ret = tegra_pcie_dw_parse_dt(pcie);
+ if (ret < 0) {
+ dev_err(dev, "Failed to parse device tree: %d\n", ret);
+ return ret;
+ }
+
+ pcie->pex_ctl_supply = devm_regulator_get(dev, "vddio-pex-ctl");
+ if (IS_ERR(pcie->pex_ctl_supply)) {
+ dev_err(dev, "Failed to get regulator: %ld\n",
+ PTR_ERR(pcie->pex_ctl_supply));
+ return PTR_ERR(pcie->pex_ctl_supply);
+ }
+
+ pcie->core_clk = devm_clk_get(dev, "core");
+ if (IS_ERR(pcie->core_clk)) {
+ dev_err(dev, "Failed to get core clock: %ld\n",
+ PTR_ERR(pcie->core_clk));
+ return PTR_ERR(pcie->core_clk);
+ }
+
+ pcie->appl_res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+ "appl");
+ if (!pcie->appl_res) {
+ dev_err(dev, "Failed to find \"appl\" region\n");
+ return PTR_ERR(pcie->appl_res);
+ }
+ pcie->appl_base = devm_ioremap_resource(dev, pcie->appl_res);
+ if (IS_ERR(pcie->appl_base))
+ return PTR_ERR(pcie->appl_base);
+
+ pcie->core_apb_rst = devm_reset_control_get(dev, "apb");
+ if (IS_ERR(pcie->core_apb_rst)) {
+ dev_err(dev, "Failed to get APB reset: %ld\n",
+ PTR_ERR(pcie->core_apb_rst));
+ return PTR_ERR(pcie->core_apb_rst);
+ }
+
+ phys = devm_kcalloc(dev, pcie->phy_count, sizeof(*phys), GFP_KERNEL);
+ if (!phys)
+ return PTR_ERR(phys);
+
+ for (i = 0; i < pcie->phy_count; i++) {
+ name = kasprintf(GFP_KERNEL, "p2u-%u", i);
+ if (!name) {
+ dev_err(dev, "Failed to create P2U string\n");
+ return -ENOMEM;
+ }
+ phys[i] = devm_phy_get(dev, name);
+ kfree(name);
+ if (IS_ERR(phys[i])) {
+ ret = PTR_ERR(phys[i]);
+ dev_err(dev, "Failed to get PHY: %d\n", ret);
+ return ret;
+ }
+ }
+
+ pcie->phys = phys;
+
+ dbi_res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dbi");
+ if (!dbi_res) {
+ dev_err(dev, "Failed to find \"dbi\" region\n");
+ return PTR_ERR(dbi_res);
+ }
+ pcie->dbi_res = dbi_res;
+
+ pci->dbi_base = devm_ioremap_resource(dev, dbi_res);
+ if (IS_ERR(pci->dbi_base))
+ return PTR_ERR(pci->dbi_base);
+
+ /* Tegra HW locates DBI2 at a fixed offset from DBI */
+ pci->dbi_base2 = pci->dbi_base + 0x1000;
+
+ atu_dma_res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+ "atu_dma");
+ if (!atu_dma_res) {
+ dev_err(dev, "Failed to find \"atu_dma\" region\n");
+ return PTR_ERR(atu_dma_res);
+ }
+ pcie->atu_dma_res = atu_dma_res;
+ pci->atu_base = devm_ioremap_resource(dev, atu_dma_res);
+ if (IS_ERR(pci->atu_base))
+ return PTR_ERR(pci->atu_base);
+
+ pcie->core_rst = devm_reset_control_get(dev, "core");
+ if (IS_ERR(pcie->core_rst)) {
+ dev_err(dev, "Failed to get core reset: %ld\n",
+ PTR_ERR(pcie->core_rst));
+ return PTR_ERR(pcie->core_rst);
+ }
+
+ pp->irq = platform_get_irq_byname(pdev, "intr");
+ if (!pp->irq) {
+ dev_err(dev, "Failed to get \"intr\" interrupt\n");
+ return -ENODEV;
+ }
+
+ ret = devm_request_irq(dev, pp->irq, tegra_pcie_irq_handler,
+ IRQF_SHARED, "tegra-pcie-intr", pcie);
+ if (ret) {
+ dev_err(dev, "Failed to request IRQ %d: %d\n", pp->irq, ret);
+ return ret;
+ }
+
+ pcie->bpmp = tegra_bpmp_get(dev);
+ if (IS_ERR(pcie->bpmp))
+ return PTR_ERR(pcie->bpmp);
+
+ platform_set_drvdata(pdev, pcie);
+
+ if (pcie->mode == DW_PCIE_RC_TYPE) {
+ ret = tegra_pcie_config_rp(pcie);
+ if (ret && ret != -ENOMEDIUM)
+ goto fail;
+ else
+ return 0;
+ }
+
+fail:
+ tegra_bpmp_put(pcie->bpmp);
+ return ret;
+}
+
+static int tegra_pcie_dw_remove(struct platform_device *pdev)
+{
+ struct tegra_pcie_dw *pcie = platform_get_drvdata(pdev);
+
+ if (pcie->mode != DW_PCIE_RC_TYPE)
+ return 0;
+
+ if (!pcie->link_state)
+ return 0;
+
+ debugfs_remove_recursive(pcie->debugfs);
+ tegra_pcie_deinit_controller(pcie);
+ pm_runtime_put_sync(pcie->dev);
+ pm_runtime_disable(pcie->dev);
+ tegra_bpmp_put(pcie->bpmp);
+
+ return 0;
+}
+
+static int tegra_pcie_dw_suspend_late(struct device *dev)
+{
+ struct tegra_pcie_dw *pcie = dev_get_drvdata(dev);
+ u32 val;
+
+ if (!pcie->link_state)
+ return 0;
+
+ /* Enable HW_HOT_RST mode */
+ val = appl_readl(pcie, APPL_CTRL);
+ val &= ~(APPL_CTRL_HW_HOT_RST_MODE_MASK <<
+ APPL_CTRL_HW_HOT_RST_MODE_SHIFT);
+ val |= APPL_CTRL_HW_HOT_RST_EN;
+ appl_writel(pcie, val, APPL_CTRL);
+
+ return 0;
+}
+
+static int tegra_pcie_dw_suspend_noirq(struct device *dev)
+{
+ struct tegra_pcie_dw *pcie = dev_get_drvdata(dev);
+
+ if (!pcie->link_state)
+ return 0;
+
+ /* Save MSI interrupt vector */
+ pcie->msi_ctrl_int = dw_pcie_readl_dbi(&pcie->pci,
+ PORT_LOGIC_MSI_CTRL_INT_0_EN);
+ tegra_pcie_downstream_dev_to_D0(pcie);
+ tegra_pcie_dw_pme_turnoff(pcie);
+ return __deinit_controller(pcie);
+}
+
+static int tegra_pcie_dw_resume_noirq(struct device *dev)
+{
+ struct tegra_pcie_dw *pcie = dev_get_drvdata(dev);
+ int ret;
+
+ if (!pcie->link_state)
+ return 0;
+
+ ret = tegra_pcie_config_controller(pcie, true);
+ if (ret < 0)
+ return ret;
+
+ ret = tegra_pcie_dw_host_init(&pcie->pci.pp);
+ if (ret < 0) {
+ dev_err(dev, "Failed to init host: %d\n", ret);
+ goto fail_host_init;
+ }
+
+ /* Restore MSI interrupt vector */
+ dw_pcie_writel_dbi(&pcie->pci, PORT_LOGIC_MSI_CTRL_INT_0_EN,
+ pcie->msi_ctrl_int);
+
+ return 0;
+fail_host_init:
+ return __deinit_controller(pcie);
+}
+
+static int tegra_pcie_dw_resume_early(struct device *dev)
+{
+ struct tegra_pcie_dw *pcie = dev_get_drvdata(dev);
+ u32 val;
+
+ if (!pcie->link_state)
+ return 0;
+
+ /* Disable HW_HOT_RST mode */
+ val = appl_readl(pcie, APPL_CTRL);
+ val &= ~(APPL_CTRL_HW_HOT_RST_MODE_MASK <<
+ APPL_CTRL_HW_HOT_RST_MODE_SHIFT);
+ val |= APPL_CTRL_HW_HOT_RST_MODE_IMDT_RST <<
+ APPL_CTRL_HW_HOT_RST_MODE_SHIFT;
+ val &= ~APPL_CTRL_HW_HOT_RST_EN;
+ appl_writel(pcie, val, APPL_CTRL);
+
+ return 0;
+}
+
+static void tegra_pcie_dw_shutdown(struct platform_device *pdev)
+{
+ struct tegra_pcie_dw *pcie = platform_get_drvdata(pdev);
+
+ if (pcie->mode != DW_PCIE_RC_TYPE)
+ return;
+
+ if (!pcie->link_state)
+ return;
+
+ debugfs_remove_recursive(pcie->debugfs);
+ tegra_pcie_downstream_dev_to_D0(pcie);
+
+ disable_irq(pcie->pci.pp.irq);
+ if (IS_ENABLED(CONFIG_PCI_MSI))
+ disable_irq(pcie->pci.pp.msi_irq);
+
+ tegra_pcie_dw_pme_turnoff(pcie);
+ __deinit_controller(pcie);
+}
+
+static const struct dev_pm_ops tegra_pcie_dw_pm_ops = {
+ .suspend_late = tegra_pcie_dw_suspend_late,
+ .suspend_noirq = tegra_pcie_dw_suspend_noirq,
+ .resume_noirq = tegra_pcie_dw_resume_noirq,
+ .resume_early = tegra_pcie_dw_resume_early,
+};
+
+static struct platform_driver tegra_pcie_dw_driver = {
+ .probe = tegra_pcie_dw_probe,
+ .remove = tegra_pcie_dw_remove,
+ .shutdown = tegra_pcie_dw_shutdown,
+ .driver = {
+ .name = "tegra194-pcie",
+ .pm = &tegra_pcie_dw_pm_ops,
+ .of_match_table = tegra_pcie_dw_of_match,
+ },
+};
+module_platform_driver(tegra_pcie_dw_driver);
+
+MODULE_AUTHOR("Vidya Sagar <vidyas@nvidia.com>");
+MODULE_DESCRIPTION("NVIDIA PCIe host controller driver");
+MODULE_LICENSE("GPL v2");
--
2.17.1
^ permalink raw reply related
* [PATCH V13 11/12] phy: tegra: Add PCIe PIPE2UPHY support
From: Vidya Sagar @ 2019-07-10 6:22 UTC (permalink / raw)
To: lorenzo.pieralisi, bhelgaas, robh+dt, mark.rutland,
thierry.reding, jonathanh, kishon, catalin.marinas, will.deacon,
jingoohan1, gustavo.pimentel
Cc: digetx, mperttunen, linux-pci, devicetree, linux-tegra,
linux-kernel, linux-arm-kernel, kthota, mmaddireddy, vidyas,
sagar.tv
In-Reply-To: <20190710062212.1745-1-vidyas@nvidia.com>
Synopsys DesignWare core based PCIe controllers in Tegra 194 SoC interface
with Universal PHY (UPHY) module through a PIPE2UPHY (P2U) module.
For each PCIe lane of a controller, there is a P2U unit instantiated at
hardware level. This driver provides support for the programming required
for each P2U that is going to be used for a PCIe controller.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
---
V13:
* None
V12:
* None
V11:
* Replaced PTR_ERR_OR_ZERO() with PTR_ERR() as the check for zero is already
present in the code.
V10:
* Used _relaxed() versions of readl() & writel()
V9:
* Made it dependent on ARCH_TEGRA_194_SOC directly instead of ARCH_TEGRA
V8:
* Changed P2U driver file name from pcie-p2u-tegra194.c to phy-tegra194-p2u.c
V7:
* None
V6:
* Addressed review comments from Thierry
V5:
* None
V4:
* Rebased on top of linux-next top of the tree
V3:
* Replaced spaces with tabs in Kconfig file
* Sorted header file inclusion alphabetically
V2:
* Added COMPILE_TEST in Kconfig
* Removed empty phy_ops implementations
* Modified code according to DT documentation file modifications
drivers/phy/tegra/Kconfig | 7 ++
drivers/phy/tegra/Makefile | 1 +
drivers/phy/tegra/phy-tegra194-p2u.c | 120 +++++++++++++++++++++++++++
3 files changed, 128 insertions(+)
create mode 100644 drivers/phy/tegra/phy-tegra194-p2u.c
diff --git a/drivers/phy/tegra/Kconfig b/drivers/phy/tegra/Kconfig
index e516967d695b..f9817c3ae85f 100644
--- a/drivers/phy/tegra/Kconfig
+++ b/drivers/phy/tegra/Kconfig
@@ -7,3 +7,10 @@ config PHY_TEGRA_XUSB
To compile this driver as a module, choose M here: the module will
be called phy-tegra-xusb.
+
+config PHY_TEGRA194_P2U
+ tristate "NVIDIA Tegra194 PIPE2UPHY PHY driver"
+ depends on ARCH_TEGRA_194_SOC || COMPILE_TEST
+ select GENERIC_PHY
+ help
+ Enable this to support the P2U (PIPE to UPHY) that is part of Tegra 19x SOCs.
diff --git a/drivers/phy/tegra/Makefile b/drivers/phy/tegra/Makefile
index 64ccaeacb631..320dd389f34d 100644
--- a/drivers/phy/tegra/Makefile
+++ b/drivers/phy/tegra/Makefile
@@ -6,3 +6,4 @@ phy-tegra-xusb-$(CONFIG_ARCH_TEGRA_124_SOC) += xusb-tegra124.o
phy-tegra-xusb-$(CONFIG_ARCH_TEGRA_132_SOC) += xusb-tegra124.o
phy-tegra-xusb-$(CONFIG_ARCH_TEGRA_210_SOC) += xusb-tegra210.o
phy-tegra-xusb-$(CONFIG_ARCH_TEGRA_186_SOC) += xusb-tegra186.o
+obj-$(CONFIG_PHY_TEGRA194_P2U) += phy-tegra194-p2u.o
diff --git a/drivers/phy/tegra/phy-tegra194-p2u.c b/drivers/phy/tegra/phy-tegra194-p2u.c
new file mode 100644
index 000000000000..7042bed9feaa
--- /dev/null
+++ b/drivers/phy/tegra/phy-tegra194-p2u.c
@@ -0,0 +1,120 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * P2U (PIPE to UPHY) driver for Tegra T194 SoC
+ *
+ * Copyright (C) 2019 NVIDIA Corporation.
+ *
+ * Author: Vidya Sagar <vidyas@nvidia.com>
+ */
+
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/phy/phy.h>
+
+#define P2U_PERIODIC_EQ_CTRL_GEN3 0xc0
+#define P2U_PERIODIC_EQ_CTRL_GEN3_PERIODIC_EQ_EN BIT(0)
+#define P2U_PERIODIC_EQ_CTRL_GEN3_INIT_PRESET_EQ_TRAIN_EN BIT(1)
+#define P2U_PERIODIC_EQ_CTRL_GEN4 0xc4
+#define P2U_PERIODIC_EQ_CTRL_GEN4_INIT_PRESET_EQ_TRAIN_EN BIT(1)
+
+#define P2U_RX_DEBOUNCE_TIME 0xa4
+#define P2U_RX_DEBOUNCE_TIME_DEBOUNCE_TIMER_MASK 0xffff
+#define P2U_RX_DEBOUNCE_TIME_DEBOUNCE_TIMER_VAL 160
+
+struct tegra_p2u {
+ void __iomem *base;
+};
+
+static inline void p2u_writel(struct tegra_p2u *phy, const u32 value,
+ const u32 reg)
+{
+ writel_relaxed(value, phy->base + reg);
+}
+
+static inline u32 p2u_readl(struct tegra_p2u *phy, const u32 reg)
+{
+ return readl_relaxed(phy->base + reg);
+}
+
+static int tegra_p2u_power_on(struct phy *x)
+{
+ struct tegra_p2u *phy = phy_get_drvdata(x);
+ u32 val;
+
+ val = p2u_readl(phy, P2U_PERIODIC_EQ_CTRL_GEN3);
+ val &= ~P2U_PERIODIC_EQ_CTRL_GEN3_PERIODIC_EQ_EN;
+ val |= P2U_PERIODIC_EQ_CTRL_GEN3_INIT_PRESET_EQ_TRAIN_EN;
+ p2u_writel(phy, val, P2U_PERIODIC_EQ_CTRL_GEN3);
+
+ val = p2u_readl(phy, P2U_PERIODIC_EQ_CTRL_GEN4);
+ val |= P2U_PERIODIC_EQ_CTRL_GEN4_INIT_PRESET_EQ_TRAIN_EN;
+ p2u_writel(phy, val, P2U_PERIODIC_EQ_CTRL_GEN4);
+
+ val = p2u_readl(phy, P2U_RX_DEBOUNCE_TIME);
+ val &= ~P2U_RX_DEBOUNCE_TIME_DEBOUNCE_TIMER_MASK;
+ val |= P2U_RX_DEBOUNCE_TIME_DEBOUNCE_TIMER_VAL;
+ p2u_writel(phy, val, P2U_RX_DEBOUNCE_TIME);
+
+ return 0;
+}
+
+static const struct phy_ops ops = {
+ .power_on = tegra_p2u_power_on,
+ .owner = THIS_MODULE,
+};
+
+static int tegra_p2u_probe(struct platform_device *pdev)
+{
+ struct phy_provider *phy_provider;
+ struct device *dev = &pdev->dev;
+ struct phy *generic_phy;
+ struct tegra_p2u *phy;
+ struct resource *res;
+
+ phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
+ if (!phy)
+ return -ENOMEM;
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "ctl");
+ phy->base = devm_ioremap_resource(dev, res);
+ if (IS_ERR(phy->base))
+ return PTR_ERR(phy->base);
+
+ platform_set_drvdata(pdev, phy);
+
+ generic_phy = devm_phy_create(dev, NULL, &ops);
+ if (IS_ERR(generic_phy))
+ return PTR_ERR(generic_phy);
+
+ phy_set_drvdata(generic_phy, phy);
+
+ phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+ if (IS_ERR(phy_provider))
+ return PTR_ERR(phy_provider);
+
+ return 0;
+}
+
+static const struct of_device_id tegra_p2u_id_table[] = {
+ {
+ .compatible = "nvidia,tegra194-p2u",
+ },
+ {}
+};
+MODULE_DEVICE_TABLE(of, tegra_p2u_id_table);
+
+static struct platform_driver tegra_p2u_driver = {
+ .probe = tegra_p2u_probe,
+ .driver = {
+ .name = "tegra194-p2u",
+ .of_match_table = tegra_p2u_id_table,
+ },
+};
+module_platform_driver(tegra_p2u_driver);
+
+MODULE_AUTHOR("Vidya Sagar <vidyas@nvidia.com>");
+MODULE_DESCRIPTION("NVIDIA Tegra194 PIPE2UPHY PHY driver");
+MODULE_LICENSE("GPL v2");
--
2.17.1
^ permalink raw reply related
* [PATCH V13 10/12] dt-bindings: PHY: P2U: Add Tegra194 P2U block
From: Vidya Sagar @ 2019-07-10 6:22 UTC (permalink / raw)
To: lorenzo.pieralisi, bhelgaas, robh+dt, mark.rutland,
thierry.reding, jonathanh, kishon, catalin.marinas, will.deacon,
jingoohan1, gustavo.pimentel
Cc: digetx, mperttunen, linux-pci, devicetree, linux-tegra,
linux-kernel, linux-arm-kernel, kthota, mmaddireddy, vidyas,
sagar.tv
In-Reply-To: <20190710062212.1745-1-vidyas@nvidia.com>
Add support for Tegra194 P2U (PIPE to UPHY) module block which is a glue
module instantiated one for each PCIe lane between Synopsys DesignWare core
based PCIe IP and Universal PHY block.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
---
V13:
* None
V12:
* None
V11:
* None
V10:
* None
V9:
* None
V8:
* None
V7:
* None
V6:
* Added Sob
* Changed node name from "p2u@xxxxxxxx" to "phy@xxxxxxxx"
V5:
* None
V4:
* None
V3:
* Changed node label to reflect new format that includes either 'hsio' or
'nvhs' in its name to reflect which UPHY brick they belong to
V2:
* This is a new patch in v2 series
.../bindings/phy/phy-tegra194-p2u.txt | 28 +++++++++++++++++++
1 file changed, 28 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/phy-tegra194-p2u.txt
diff --git a/Documentation/devicetree/bindings/phy/phy-tegra194-p2u.txt b/Documentation/devicetree/bindings/phy/phy-tegra194-p2u.txt
new file mode 100644
index 000000000000..d23ff90baad5
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/phy-tegra194-p2u.txt
@@ -0,0 +1,28 @@
+NVIDIA Tegra194 P2U binding
+
+Tegra194 has two PHY bricks namely HSIO (High Speed IO) and NVHS (NVIDIA High
+Speed) each interfacing with 12 and 8 P2U instances respectively.
+A P2U instance is a glue logic between Synopsys DesignWare Core PCIe IP's PIPE
+interface and PHY of HSIO/NVHS bricks. Each P2U instance represents one PCIe
+lane.
+
+Required properties:
+- compatible: For Tegra19x, must contain "nvidia,tegra194-p2u".
+- reg: Should be the physical address space and length of respective each P2U
+ instance.
+- reg-names: Must include the entry "ctl".
+
+Required properties for PHY port node:
+- #phy-cells: Defined by generic PHY bindings. Must be 0.
+
+Refer to phy/phy-bindings.txt for the generic PHY binding properties.
+
+Example:
+
+p2u_hsio_0: phy@3e10000 {
+ compatible = "nvidia,tegra194-p2u";
+ reg = <0x03e10000 0x10000>;
+ reg-names = "ctl";
+
+ #phy-cells = <0>;
+};
--
2.17.1
^ permalink raw reply related
* [PATCH V13 09/12] dt-bindings: PCI: tegra: Add device tree support for Tegra194
From: Vidya Sagar @ 2019-07-10 6:22 UTC (permalink / raw)
To: lorenzo.pieralisi, bhelgaas, robh+dt, mark.rutland,
thierry.reding, jonathanh, kishon, catalin.marinas, will.deacon,
jingoohan1, gustavo.pimentel
Cc: digetx, mperttunen, linux-pci, devicetree, linux-tegra,
linux-kernel, linux-arm-kernel, kthota, mmaddireddy, vidyas,
sagar.tv
In-Reply-To: <20190710062212.1745-1-vidyas@nvidia.com>
Add support for Tegra194 PCIe controllers. These controllers are based
on Synopsys DesignWare core IP.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
---
V13:
* None
V12:
* None
V11:
* None
V10:
* None
V9:
* Added Acked-by from Thierry
V8:
* Addressed review comments from Thierry
* Modified DT example to reflect new changes
V7:
* Changed description of the property "nvidia,bpmp".
* Removed property "nvidia,disable-aspm-states".
V6:
* Removed 'max-link-speed' as it is going to be a common sub-system property
* Removed 'nvidia,init-link-speed' as there isn't much value addition
* Removed 'nvidia,wake-gpios' for now
* Addressed review comments from Thierry and Rob in general
V5:
* None
V4:
* None
V3:
* Using only 'Cx' (x-being controller number) format to represent a controller
* Changed to 'value: description' format where applicable
* Changed 'nvidia,init-speed' to 'nvidia,init-link-speed'
* Provided more documentation for 'nvidia,init-link-speed' property
* Changed 'nvidia,pex-wake' to 'nvidia,wake-gpios'
V2:
* Added documentation for 'power-domains' property
* Removed 'window1' and 'window2' properties
* Removed '_clk' and '_rst' from clock and reset names
* Dropped 'pcie' from phy-names
* Added entry for BPMP-FW handle
* Removed offsets for some of the registers and added them in code and would be pickedup based on
controller ID
* Changed 'nvidia,max-speed' to 'max-link-speed' and is made as an optional
* Changed 'nvidia,disable-clock-request' to 'supports-clkreq' with inverted operation
* Added more documentation for 'nvidia,update-fc-fixup' property
* Removed 'nvidia,enable-power-down' and 'nvidia,plat-gpios' properties
* Added '-us' to all properties that represent time in microseconds
* Moved P2U documentation to a separate file
.../bindings/pci/nvidia,tegra194-pcie.txt | 155 ++++++++++++++++++
1 file changed, 155 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt
diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt
new file mode 100644
index 000000000000..674e5adb2895
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt
@@ -0,0 +1,155 @@
+NVIDIA Tegra PCIe controller (Synopsys DesignWare Core based)
+
+This PCIe host controller is based on the Synopsis Designware PCIe IP
+and thus inherits all the common properties defined in designware-pcie.txt.
+
+Required properties:
+- compatible: For Tegra19x, must contain "nvidia,tegra194-pcie".
+- device_type: Must be "pci"
+- power-domains: A phandle to the node that controls power to the respective
+ PCIe controller and a specifier name for the PCIe controller. Following are
+ the specifiers for the different PCIe controllers
+ TEGRA194_POWER_DOMAIN_PCIEX8B: C0
+ TEGRA194_POWER_DOMAIN_PCIEX1A: C1
+ TEGRA194_POWER_DOMAIN_PCIEX1A: C2
+ TEGRA194_POWER_DOMAIN_PCIEX1A: C3
+ TEGRA194_POWER_DOMAIN_PCIEX4A: C4
+ TEGRA194_POWER_DOMAIN_PCIEX8A: C5
+ these specifiers are defined in
+ "include/dt-bindings/power/tegra194-powergate.h" file.
+- reg: A list of physical base address and length pairs for each set of
+ controller registers. Must contain an entry for each entry in the reg-names
+ property.
+- reg-names: Must include the following entries:
+ "appl": Controller's application logic registers
+ "config": As per the definition in designware-pcie.txt
+ "atu_dma": iATU and DMA registers. This is where the iATU (internal Address
+ Translation Unit) registers of the PCIe core are made available
+ for SW access.
+ "dbi": The aperture where root port's own configuration registers are
+ available
+- interrupts: A list of interrupt outputs of the controller. Must contain an
+ entry for each entry in the interrupt-names property.
+- interrupt-names: Must include the following entries:
+ "intr": The Tegra interrupt that is asserted for controller interrupts
+ "msi": The Tegra interrupt that is asserted when an MSI is received
+- bus-range: Range of bus numbers associated with this controller
+- #address-cells: Address representation for root ports (must be 3)
+ - cell 0 specifies the bus and device numbers of the root port:
+ [23:16]: bus number
+ [15:11]: device number
+ - cell 1 denotes the upper 32 address bits and should be 0
+ - cell 2 contains the lower 32 address bits and is used to translate to the
+ CPU address space
+- #size-cells: Size representation for root ports (must be 2)
+- ranges: Describes the translation of addresses for root ports and standard
+ PCI regions. The entries must be 7 cells each, where the first three cells
+ correspond to the address as described for the #address-cells property
+ above, the fourth and fifth cells are for the physical CPU address to
+ translate to and the sixth and seventh cells are as described for the
+ #size-cells property above.
+ - Entries setup the mapping for the standard I/O, memory and
+ prefetchable PCI regions. The first cell determines the type of region
+ that is setup:
+ - 0x81000000: I/O memory region
+ - 0x82000000: non-prefetchable memory region
+ - 0xc2000000: prefetchable memory region
+ Please refer to the standard PCI bus binding document for a more detailed
+ explanation.
+- #interrupt-cells: Size representation for interrupts (must be 1)
+- interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties
+ Please refer to the standard PCI bus binding document for a more detailed
+ explanation.
+- clocks: Must contain an entry for each entry in clock-names.
+ See ../clocks/clock-bindings.txt for details.
+- clock-names: Must include the following entries:
+ - core
+- resets: Must contain an entry for each entry in reset-names.
+ See ../reset/reset.txt for details.
+- reset-names: Must include the following entries:
+ - apb
+ - core
+- phys: Must contain a phandle to P2U PHY for each entry in phy-names.
+- phy-names: Must include an entry for each active lane.
+ "p2u-N": where N ranges from 0 to one less than the total number of lanes
+- nvidia,bpmp: Must contain a pair of phandle to BPMP controller node followed
+ by controller-id. Following are the controller ids for each controller.
+ 0: C0
+ 1: C1
+ 2: C2
+ 3: C3
+ 4: C4
+ 5: C5
+- vddio-pex-ctl-supply: Regulator supply for PCIe side band signals
+
+Optional properties:
+- supports-clkreq: Refer to Documentation/devicetree/bindings/pci/pci.txt
+- nvidia,update-fc-fixup: This is a boolean property and needs to be present to
+ improve performance when a platform is designed in such a way that it
+ satisfies at least one of the following conditions thereby enabling root
+ port to exchange optimum number of FC (Flow Control) credits with
+ downstream devices
+ 1. If C0/C4/C5 run at x1/x2 link widths (irrespective of speed and MPS)
+ 2. If C0/C1/C2/C3/C4/C5 operate at their respective max link widths and
+ a) speed is Gen-2 and MPS is 256B
+ b) speed is >= Gen-3 with any MPS
+- nvidia,aspm-cmrt-us: Common Mode Restore Time for proper operation of ASPM
+ to be specified in microseconds
+- nvidia,aspm-pwr-on-t-us: Power On time for proper operation of ASPM to be
+ specified in microseconds
+- nvidia,aspm-l0s-entrance-latency-us: ASPM L0s entrance latency to be
+ specified in microseconds
+
+Examples:
+=========
+
+Tegra194:
+--------
+
+ pcie@14180000 {
+ compatible = "nvidia,tegra194-pcie", "snps,dw-pcie";
+ power-domains = <&bpmp TEGRA194_POWER_DOMAIN_PCIEX8B>;
+ reg = <0x00 0x14180000 0x0 0x00020000 /* appl registers (128K) */
+ 0x00 0x38000000 0x0 0x00040000 /* configuration space (256K) */
+ 0x00 0x38040000 0x0 0x00040000>; /* iATU_DMA reg space (256K) */
+ reg-names = "appl", "config", "atu_dma";
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ num-lanes = <8>;
+ linux,pci-domain = <0>;
+
+ clocks = <&bpmp TEGRA194_CLK_PEX0_CORE_0>;
+ clock-names = "core";
+
+ resets = <&bpmp TEGRA194_RESET_PEX0_CORE_0_APB>,
+ <&bpmp TEGRA194_RESET_PEX0_CORE_0>;
+ reset-names = "apb", "core";
+
+ interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */
+ <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */
+ interrupt-names = "intr", "msi";
+
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &gic GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+
+ nvidia,bpmp = <&bpmp 0>;
+
+ supports-clkreq;
+ nvidia,aspm-cmrt-us = <60>;
+ nvidia,aspm-pwr-on-t-us = <20>;
+ nvidia,aspm-l0s-entrance-latency-us = <3>;
+
+ bus-range = <0x0 0xff>;
+ ranges = <0x81000000 0x0 0x38100000 0x0 0x38100000 0x0 0x00100000 /* downstream I/O (1MB) */
+ 0x82000000 0x0 0x38200000 0x0 0x38200000 0x0 0x01E00000 /* non-prefetchable memory (30MB) */
+ 0xc2000000 0x18 0x00000000 0x18 0x00000000 0x4 0x00000000>; /* prefetchable memory (16GB) */
+
+ vddio-pex-ctl-supply = <&vdd_1v8ao>;
+
+ phys = <&p2u_hsio_2>, <&p2u_hsio_3>, <&p2u_hsio_4>,
+ <&p2u_hsio_5>;
+ phy-names = "p2u-0", "p2u-1", "p2u-2", "p2u-3";
+ };
--
2.17.1
^ permalink raw reply related
* [PATCH V13 08/12] dt-bindings: Add PCIe supports-clkreq property
From: Vidya Sagar @ 2019-07-10 6:22 UTC (permalink / raw)
To: lorenzo.pieralisi, bhelgaas, robh+dt, mark.rutland,
thierry.reding, jonathanh, kishon, catalin.marinas, will.deacon,
jingoohan1, gustavo.pimentel
Cc: digetx, mperttunen, linux-pci, devicetree, linux-tegra,
linux-kernel, linux-arm-kernel, kthota, mmaddireddy, vidyas,
sagar.tv
In-Reply-To: <20190710062212.1745-1-vidyas@nvidia.com>
Some host controllers need to know the existence of clkreq signal routing to
downstream devices to be able to advertise low power features like ASPM L1
substates. Without clkreq signal routing being present, enabling ASPM L1 sub
states might lead to downstream devices falling off the bus. Hence a new device
tree property 'supports-clkreq' is added to make such host controllers
aware of clkreq signal routing to downstream devices.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>
---
V13:
* None
V12:
* Rebased on top of linux-next top of the tree
V11:
* None
V10:
* None
V9:
* None
V8:
* None
V7:
* None
V6:
* s/Documentation\/devicetree/dt-bindings/ in the subject
V5:
* None
V4:
* Rebased on top of linux-next top of the tree
V3:
* None
V2:
* This is a new patch in v2 series
Documentation/devicetree/bindings/pci/pci.txt | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/Documentation/devicetree/bindings/pci/pci.txt b/Documentation/devicetree/bindings/pci/pci.txt
index 2a5d91024059..29bcbd88f457 100644
--- a/Documentation/devicetree/bindings/pci/pci.txt
+++ b/Documentation/devicetree/bindings/pci/pci.txt
@@ -27,6 +27,11 @@ driver implementation may support the following properties:
- reset-gpios:
If present this property specifies PERST# GPIO. Host drivers can parse the
GPIO and apply fundamental reset to endpoints.
+- supports-clkreq:
+ If present this property specifies that CLKREQ signal routing exists from
+ root port to downstream device and host bridge drivers can do programming
+ which depends on CLKREQ signal existence. For example, programming root port
+ not to advertise ASPM L1 Sub-States support if there is no CLKREQ signal.
PCI-PCI Bridge properties
-------------------------
--
2.17.1
^ permalink raw reply related
* [PATCH V13 07/12] PCI: dwc: Add support to enable CDM register check
From: Vidya Sagar @ 2019-07-10 6:22 UTC (permalink / raw)
To: lorenzo.pieralisi, bhelgaas, robh+dt, mark.rutland,
thierry.reding, jonathanh, kishon, catalin.marinas, will.deacon,
jingoohan1, gustavo.pimentel
Cc: digetx, mperttunen, linux-pci, devicetree, linux-tegra,
linux-kernel, linux-arm-kernel, kthota, mmaddireddy, vidyas,
sagar.tv
In-Reply-To: <20190710062212.1745-1-vidyas@nvidia.com>
Add support to enable CDM (Configuration Dependent Module) register check
for any data corruption based on the device-tree flag 'snps,enable-cdm-check'.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
---
V13:
* None
V12:
* None
V11:
* None
V10:
* None
V9:
* None
V8:
* None
V7:
* Changed "enable-cdm-check" to "snps,enable-cdm-check"
V6:
* None
V5:
* None
V4:
* None
V3:
* Changed code and commit description to reflect change in flag from
'cdm-check' to 'enable-cdm-check'
V2:
* This is a new patch in v2 series
drivers/pci/controller/dwc/pcie-designware.c | 7 +++++++
drivers/pci/controller/dwc/pcie-designware.h | 9 +++++++++
2 files changed, 16 insertions(+)
diff --git a/drivers/pci/controller/dwc/pcie-designware.c b/drivers/pci/controller/dwc/pcie-designware.c
index 181449e342f1..01f9227a5ade 100644
--- a/drivers/pci/controller/dwc/pcie-designware.c
+++ b/drivers/pci/controller/dwc/pcie-designware.c
@@ -546,4 +546,11 @@ void dw_pcie_setup(struct dw_pcie *pci)
break;
}
dw_pcie_writel_dbi(pci, PCIE_LINK_WIDTH_SPEED_CONTROL, val);
+
+ if (of_property_read_bool(np, "snps,enable-cdm-check")) {
+ val = dw_pcie_readl_dbi(pci, PCIE_PL_CHK_REG_CONTROL_STATUS);
+ val |= PCIE_PL_CHK_REG_CHK_REG_CONTINUOUS |
+ PCIE_PL_CHK_REG_CHK_REG_START;
+ dw_pcie_writel_dbi(pci, PCIE_PL_CHK_REG_CONTROL_STATUS, val);
+ }
}
diff --git a/drivers/pci/controller/dwc/pcie-designware.h b/drivers/pci/controller/dwc/pcie-designware.h
index 11c223471416..5a18e94e52c8 100644
--- a/drivers/pci/controller/dwc/pcie-designware.h
+++ b/drivers/pci/controller/dwc/pcie-designware.h
@@ -86,6 +86,15 @@
#define PCIE_MISC_CONTROL_1_OFF 0x8BC
#define PCIE_DBI_RO_WR_EN BIT(0)
+#define PCIE_PL_CHK_REG_CONTROL_STATUS 0xB20
+#define PCIE_PL_CHK_REG_CHK_REG_START BIT(0)
+#define PCIE_PL_CHK_REG_CHK_REG_CONTINUOUS BIT(1)
+#define PCIE_PL_CHK_REG_CHK_REG_COMPARISON_ERROR BIT(16)
+#define PCIE_PL_CHK_REG_CHK_REG_LOGIC_ERROR BIT(17)
+#define PCIE_PL_CHK_REG_CHK_REG_COMPLETE BIT(18)
+
+#define PCIE_PL_CHK_REG_ERR_ADDR 0xB28
+
/*
* iATU Unroll-specific register definitions
* From 4.80 core version the address translation will be made by unroll
--
2.17.1
^ permalink raw reply related
* [PATCH V13 06/12] dt-bindings: PCI: designware: Add binding for CDM register check
From: Vidya Sagar @ 2019-07-10 6:22 UTC (permalink / raw)
To: lorenzo.pieralisi, bhelgaas, robh+dt, mark.rutland,
thierry.reding, jonathanh, kishon, catalin.marinas, will.deacon,
jingoohan1, gustavo.pimentel
Cc: digetx, mperttunen, linux-pci, devicetree, linux-tegra,
linux-kernel, linux-arm-kernel, kthota, mmaddireddy, vidyas,
sagar.tv
In-Reply-To: <20190710062212.1745-1-vidyas@nvidia.com>
Add support to enable CDM (Configuration Dependent Module) registers check
for any data corruption. CDM registers include standard PCIe configuration
space registers, Port Logic registers and iATU and DMA registers.
Refer Section S.4 of Synopsys DesignWare Cores PCI Express Controller Databook
Version 4.90a
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
V13:
* None
V12:
* None
V11:
* None
V10:
* None
V9:
* None
V8:
* None
V7:
* Changed "enable-cdm-check" to "snps,enable-cdm-check"
V6:
* None
V5:
* None
V4:
* None
V3:
* Changed flag name from 'cdm-check' to 'enable-cdm-check'
* Added info about Port Logic and DMA registers being part of CDM
V2:
* This is a new patch in v2 series
Documentation/devicetree/bindings/pci/designware-pcie.txt | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/Documentation/devicetree/bindings/pci/designware-pcie.txt b/Documentation/devicetree/bindings/pci/designware-pcie.txt
index 5561a1c060d0..3fba04da6a59 100644
--- a/Documentation/devicetree/bindings/pci/designware-pcie.txt
+++ b/Documentation/devicetree/bindings/pci/designware-pcie.txt
@@ -34,6 +34,11 @@ Optional properties:
- clock-names: Must include the following entries:
- "pcie"
- "pcie_bus"
+- snps,enable-cdm-check: This is a boolean property and if present enables
+ automatic checking of CDM (Configuration Dependent Module) registers
+ for data corruption. CDM registers include standard PCIe configuration
+ space registers, Port Logic registers, DMA and iATU (internal Address
+ Translation Unit) registers.
RC mode:
- num-viewport: number of view ports configured in hardware. If a platform
does not specify it, the driver assumes 2.
--
2.17.1
^ permalink raw reply related
* [PATCH V13 05/12] PCI: dwc: Add ext config space capability search API
From: Vidya Sagar @ 2019-07-10 6:22 UTC (permalink / raw)
To: lorenzo.pieralisi, bhelgaas, robh+dt, mark.rutland,
thierry.reding, jonathanh, kishon, catalin.marinas, will.deacon,
jingoohan1, gustavo.pimentel
Cc: digetx, mperttunen, linux-pci, devicetree, linux-tegra,
linux-kernel, linux-arm-kernel, kthota, mmaddireddy, vidyas,
sagar.tv
In-Reply-To: <20190710062212.1745-1-vidyas@nvidia.com>
Add extended configuration space capability search API using struct dw_pcie *
pointer
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Acked-by: Thierry Reding <treding@nvidia.com>
---
V13:
* None
V12:
* None
V11:
* None
V10:
* None
V9:
* Added Acked-by from Thierry
V8:
* Changed data types of return and arguments to be inline with data being returned
and passed.
V7:
* None
V6:
* None
V5:
* None
V4:
* None
V3:
* None
V2:
* This is a new patch in v2 series
drivers/pci/controller/dwc/pcie-designware.c | 41 ++++++++++++++++++++
drivers/pci/controller/dwc/pcie-designware.h | 1 +
2 files changed, 42 insertions(+)
diff --git a/drivers/pci/controller/dwc/pcie-designware.c b/drivers/pci/controller/dwc/pcie-designware.c
index 7818b4febb08..181449e342f1 100644
--- a/drivers/pci/controller/dwc/pcie-designware.c
+++ b/drivers/pci/controller/dwc/pcie-designware.c
@@ -53,6 +53,47 @@ u8 dw_pcie_find_capability(struct dw_pcie *pci, u8 cap)
}
EXPORT_SYMBOL_GPL(dw_pcie_find_capability);
+static u16 dw_pcie_find_next_ext_capability(struct dw_pcie *pci, u16 start,
+ u8 cap)
+{
+ u32 header;
+ int ttl;
+ int pos = PCI_CFG_SPACE_SIZE;
+
+ /* minimum 8 bytes per capability */
+ ttl = (PCI_CFG_SPACE_EXP_SIZE - PCI_CFG_SPACE_SIZE) / 8;
+
+ if (start)
+ pos = start;
+
+ header = dw_pcie_readl_dbi(pci, pos);
+ /*
+ * If we have no capabilities, this is indicated by cap ID,
+ * cap version and next pointer all being 0.
+ */
+ if (header == 0)
+ return 0;
+
+ while (ttl-- > 0) {
+ if (PCI_EXT_CAP_ID(header) == cap && pos != start)
+ return pos;
+
+ pos = PCI_EXT_CAP_NEXT(header);
+ if (pos < PCI_CFG_SPACE_SIZE)
+ break;
+
+ header = dw_pcie_readl_dbi(pci, pos);
+ }
+
+ return 0;
+}
+
+u16 dw_pcie_find_ext_capability(struct dw_pcie *pci, u8 cap)
+{
+ return dw_pcie_find_next_ext_capability(pci, 0, cap);
+}
+EXPORT_SYMBOL_GPL(dw_pcie_find_ext_capability);
+
int dw_pcie_read(void __iomem *addr, int size, u32 *val)
{
if (!IS_ALIGNED((uintptr_t)addr, size)) {
diff --git a/drivers/pci/controller/dwc/pcie-designware.h b/drivers/pci/controller/dwc/pcie-designware.h
index d8c66a6827dc..11c223471416 100644
--- a/drivers/pci/controller/dwc/pcie-designware.h
+++ b/drivers/pci/controller/dwc/pcie-designware.h
@@ -252,6 +252,7 @@ struct dw_pcie {
container_of((endpoint), struct dw_pcie, ep)
u8 dw_pcie_find_capability(struct dw_pcie *pci, u8 cap);
+u16 dw_pcie_find_ext_capability(struct dw_pcie *pci, u8 cap);
int dw_pcie_read(void __iomem *addr, int size, u32 *val);
int dw_pcie_write(void __iomem *addr, int size, u32 val);
--
2.17.1
^ permalink raw reply related
* [PATCH V13 04/12] PCI: dwc: Move config space capability search API
From: Vidya Sagar @ 2019-07-10 6:22 UTC (permalink / raw)
To: lorenzo.pieralisi, bhelgaas, robh+dt, mark.rutland,
thierry.reding, jonathanh, kishon, catalin.marinas, will.deacon,
jingoohan1, gustavo.pimentel
Cc: digetx, mperttunen, linux-pci, devicetree, linux-tegra,
linux-kernel, linux-arm-kernel, kthota, mmaddireddy, vidyas,
sagar.tv
In-Reply-To: <20190710062212.1745-1-vidyas@nvidia.com>
Move PCIe config space capability search API to common DesignWare file
as this can be used by both host and ep mode codes.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
---
V13:
* None
V12:
* None
V11:
* None
V10:
* None
V9:
* None
V8:
* Changed comment to explicitly state their mere resemblance to standard APIs
but not their operation and place of use.
V7:
* Exported dw_pcie_find_capability() API
V6:
* None
V5:
* Removed redundant APIs in pcie-designware-ep.c file after moving them
to pcie-designware.c file based on Bjorn's comments.
V4:
* Rebased to linux-next top of the tree
V3:
* None
V2:
* Removed dw_pcie_find_next_ext_capability() API from here and made a
separate patch for that
.../pci/controller/dwc/pcie-designware-ep.c | 37 +-----------------
drivers/pci/controller/dwc/pcie-designware.c | 39 +++++++++++++++++++
drivers/pci/controller/dwc/pcie-designware.h | 2 +
3 files changed, 43 insertions(+), 35 deletions(-)
diff --git a/drivers/pci/controller/dwc/pcie-designware-ep.c b/drivers/pci/controller/dwc/pcie-designware-ep.c
index 2bf5a35c0570..65f479250087 100644
--- a/drivers/pci/controller/dwc/pcie-designware-ep.c
+++ b/drivers/pci/controller/dwc/pcie-designware-ep.c
@@ -40,39 +40,6 @@ void dw_pcie_ep_reset_bar(struct dw_pcie *pci, enum pci_barno bar)
__dw_pcie_ep_reset_bar(pci, bar, 0);
}
-static u8 __dw_pcie_ep_find_next_cap(struct dw_pcie *pci, u8 cap_ptr,
- u8 cap)
-{
- u8 cap_id, next_cap_ptr;
- u16 reg;
-
- if (!cap_ptr)
- return 0;
-
- reg = dw_pcie_readw_dbi(pci, cap_ptr);
- cap_id = (reg & 0x00ff);
-
- if (cap_id > PCI_CAP_ID_MAX)
- return 0;
-
- if (cap_id == cap)
- return cap_ptr;
-
- next_cap_ptr = (reg & 0xff00) >> 8;
- return __dw_pcie_ep_find_next_cap(pci, next_cap_ptr, cap);
-}
-
-static u8 dw_pcie_ep_find_capability(struct dw_pcie *pci, u8 cap)
-{
- u8 next_cap_ptr;
- u16 reg;
-
- reg = dw_pcie_readw_dbi(pci, PCI_CAPABILITY_LIST);
- next_cap_ptr = (reg & 0x00ff);
-
- return __dw_pcie_ep_find_next_cap(pci, next_cap_ptr, cap);
-}
-
static int dw_pcie_ep_write_header(struct pci_epc *epc, u8 func_no,
struct pci_epf_header *hdr)
{
@@ -612,9 +579,9 @@ int dw_pcie_ep_init(struct dw_pcie_ep *ep)
dev_err(dev, "Failed to reserve memory for MSI/MSI-X\n");
return -ENOMEM;
}
- ep->msi_cap = dw_pcie_ep_find_capability(pci, PCI_CAP_ID_MSI);
+ ep->msi_cap = dw_pcie_find_capability(pci, PCI_CAP_ID_MSI);
- ep->msix_cap = dw_pcie_ep_find_capability(pci, PCI_CAP_ID_MSIX);
+ ep->msix_cap = dw_pcie_find_capability(pci, PCI_CAP_ID_MSIX);
offset = dw_pcie_ep_find_ext_capability(pci, PCI_EXT_CAP_ID_REBAR);
if (offset) {
diff --git a/drivers/pci/controller/dwc/pcie-designware.c b/drivers/pci/controller/dwc/pcie-designware.c
index 7d25102c304c..7818b4febb08 100644
--- a/drivers/pci/controller/dwc/pcie-designware.c
+++ b/drivers/pci/controller/dwc/pcie-designware.c
@@ -14,6 +14,45 @@
#include "pcie-designware.h"
+/*
+ * These interfaces resemble the pci_find_*capability() interfaces, but these
+ * are for configuring host controllers, which are bridges *to* PCI devices but
+ * are not PCI devices themselves.
+ */
+static u8 __dw_pcie_find_next_cap(struct dw_pcie *pci, u8 cap_ptr,
+ u8 cap)
+{
+ u8 cap_id, next_cap_ptr;
+ u16 reg;
+
+ if (!cap_ptr)
+ return 0;
+
+ reg = dw_pcie_readw_dbi(pci, cap_ptr);
+ cap_id = (reg & 0x00ff);
+
+ if (cap_id > PCI_CAP_ID_MAX)
+ return 0;
+
+ if (cap_id == cap)
+ return cap_ptr;
+
+ next_cap_ptr = (reg & 0xff00) >> 8;
+ return __dw_pcie_find_next_cap(pci, next_cap_ptr, cap);
+}
+
+u8 dw_pcie_find_capability(struct dw_pcie *pci, u8 cap)
+{
+ u8 next_cap_ptr;
+ u16 reg;
+
+ reg = dw_pcie_readw_dbi(pci, PCI_CAPABILITY_LIST);
+ next_cap_ptr = (reg & 0x00ff);
+
+ return __dw_pcie_find_next_cap(pci, next_cap_ptr, cap);
+}
+EXPORT_SYMBOL_GPL(dw_pcie_find_capability);
+
int dw_pcie_read(void __iomem *addr, int size, u32 *val)
{
if (!IS_ALIGNED((uintptr_t)addr, size)) {
diff --git a/drivers/pci/controller/dwc/pcie-designware.h b/drivers/pci/controller/dwc/pcie-designware.h
index ffed084a0b4f..d8c66a6827dc 100644
--- a/drivers/pci/controller/dwc/pcie-designware.h
+++ b/drivers/pci/controller/dwc/pcie-designware.h
@@ -251,6 +251,8 @@ struct dw_pcie {
#define to_dw_pcie_from_ep(endpoint) \
container_of((endpoint), struct dw_pcie, ep)
+u8 dw_pcie_find_capability(struct dw_pcie *pci, u8 cap);
+
int dw_pcie_read(void __iomem *addr, int size, u32 *val);
int dw_pcie_write(void __iomem *addr, int size, u32 val);
--
2.17.1
^ permalink raw reply related
* [PATCH V13 03/12] PCI: dwc: Perform dbi regs write lock towards the end
From: Vidya Sagar @ 2019-07-10 6:22 UTC (permalink / raw)
To: lorenzo.pieralisi, bhelgaas, robh+dt, mark.rutland,
thierry.reding, jonathanh, kishon, catalin.marinas, will.deacon,
jingoohan1, gustavo.pimentel
Cc: digetx, mperttunen, linux-pci, devicetree, linux-tegra,
linux-kernel, linux-arm-kernel, kthota, mmaddireddy, vidyas,
sagar.tv
In-Reply-To: <20190710062212.1745-1-vidyas@nvidia.com>
Some of DesignWare core's DBI registers (a.k.a configuration space
registers) are write-protected with a lock without enabling which they are
read-only by default. These write-protected registers are implementation
specific. Tegra194's BAR-0 register which is at offset 0x10 in the
configuration space is an example. Current implementation in
dw_pcie_setup_rc() API attempts to unlock those write-protected registers
whenever they are updated and lock them back again for writing. This patch
attempts to unlock all such write-protected registers for writing in the
beginning of the API once and lock them back again towards the end to avoid
bloating the API with multiple unlock/lock sequences for all those
write-protected registers.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
---
V13:
* None
V12:
* Modified commit message to make it explicit that write-protected registers are
implementation specific.
V11:
* None
V10:
* None
V9:
* None
V8:
* None
V7:
* None
V6:
* Moved write enable to the beginning of the API and write disable to the end
V5:
* None
V4:
* None
V3:
* None
V2:
* None
drivers/pci/controller/dwc/pcie-designware-host.c | 14 ++++++++------
1 file changed, 8 insertions(+), 6 deletions(-)
diff --git a/drivers/pci/controller/dwc/pcie-designware-host.c b/drivers/pci/controller/dwc/pcie-designware-host.c
index f93252d0da5b..d3156446ff27 100644
--- a/drivers/pci/controller/dwc/pcie-designware-host.c
+++ b/drivers/pci/controller/dwc/pcie-designware-host.c
@@ -628,6 +628,12 @@ void dw_pcie_setup_rc(struct pcie_port *pp)
u32 val, ctrl, num_ctrls;
struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
+ /*
+ * Enable DBI read-only registers for writing/updating configuration.
+ * Write permission gets disabled towards the end of this function.
+ */
+ dw_pcie_dbi_ro_wr_en(pci);
+
dw_pcie_setup(pci);
if (!pp->ops->msi_host_init) {
@@ -650,12 +656,10 @@ void dw_pcie_setup_rc(struct pcie_port *pp)
dw_pcie_writel_dbi(pci, PCI_BASE_ADDRESS_1, 0x00000000);
/* Setup interrupt pins */
- dw_pcie_dbi_ro_wr_en(pci);
val = dw_pcie_readl_dbi(pci, PCI_INTERRUPT_LINE);
val &= 0xffff00ff;
val |= 0x00000100;
dw_pcie_writel_dbi(pci, PCI_INTERRUPT_LINE, val);
- dw_pcie_dbi_ro_wr_dis(pci);
/* Setup bus numbers */
val = dw_pcie_readl_dbi(pci, PCI_PRIMARY_BUS);
@@ -687,15 +691,13 @@ void dw_pcie_setup_rc(struct pcie_port *pp)
dw_pcie_wr_own_conf(pp, PCI_BASE_ADDRESS_0, 4, 0);
- /* Enable write permission for the DBI read-only register */
- dw_pcie_dbi_ro_wr_en(pci);
/* Program correct class for RC */
dw_pcie_wr_own_conf(pp, PCI_CLASS_DEVICE, 2, PCI_CLASS_BRIDGE_PCI);
- /* Better disable write permission right after the update */
- dw_pcie_dbi_ro_wr_dis(pci);
dw_pcie_rd_own_conf(pp, PCIE_LINK_WIDTH_SPEED_CONTROL, 4, &val);
val |= PORT_LOGIC_SPEED_CHANGE;
dw_pcie_wr_own_conf(pp, PCIE_LINK_WIDTH_SPEED_CONTROL, 4, val);
+
+ dw_pcie_dbi_ro_wr_dis(pci);
}
EXPORT_SYMBOL_GPL(dw_pcie_setup_rc);
--
2.17.1
^ permalink raw reply related
* [PATCH V13 02/12] PCI: Disable MSI for Tegra root ports
From: Vidya Sagar @ 2019-07-10 6:22 UTC (permalink / raw)
To: lorenzo.pieralisi, bhelgaas, robh+dt, mark.rutland,
thierry.reding, jonathanh, kishon, catalin.marinas, will.deacon,
jingoohan1, gustavo.pimentel
Cc: digetx, mperttunen, linux-pci, devicetree, linux-tegra,
linux-kernel, linux-arm-kernel, kthota, mmaddireddy, vidyas,
sagar.tv
In-Reply-To: <20190710062212.1745-1-vidyas@nvidia.com>
Tegra PCIe rootports don't generate MSI interrupts for PME and AER events.
Since PCIe spec (Ref: r4.0 sec 7.7.1.2 and 7.7.2.2) doesn't support using
a mix of INTx and MSI/MSI-X, MSI needs to be disabled to avoid root ports
service drivers registering their respective ISRs with MSI interrupt and
to let only INTx be used for all events.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
---
V13:
* None
V12:
* None
V11:
* Included older Tegra chips to extend the quirk as this issue is present in
older Tegra chips as well.
V10:
* None
V9:
* None
V8:
* Changed quirk macro to consider class code as well to avoid this quirk
getting applied to Tegra194 when it is operating in endpoint mode. Also
quoted relevant sections from PCIe spec in comments.
V7:
* This is a new patch
drivers/pci/quirks.c | 53 ++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 53 insertions(+)
diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c
index c66c0ca446c4..1d3cac43ecbc 100644
--- a/drivers/pci/quirks.c
+++ b/drivers/pci/quirks.c
@@ -2592,6 +2592,59 @@ DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_NVIDIA,
PCI_DEVICE_ID_NVIDIA_NVENET_15,
nvenet_msi_disable);
+/*
+ * PCIe spec r4.0 sec 7.7.1.2 and sec 7.7.2.2 say that if MSI/MSI-X is enabled,
+ * then the device can't use INTx interrupts. Tegra's PCIe root ports don't
+ * generate MSI interrupts for PME and AER events instead only INTx interrupts
+ * are generated. Though Tegra's PCIe root ports can generate MSI interrupts
+ * for other events, since PCIe specificiation doesn't support using a mix of
+ * INTx and MSI/MSI-X, it is required to disable MSI interrupts to avoid port
+ * service drivers registering their respective ISRs for MSIs.
+ */
+static void pci_quirk_nvidia_tegra_disable_rp_msi(struct pci_dev *dev)
+{
+ dev->no_msi = 1;
+}
+DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x1ad0,
+ PCI_CLASS_BRIDGE_PCI, 8,
+ pci_quirk_nvidia_tegra_disable_rp_msi);
+DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x1ad1,
+ PCI_CLASS_BRIDGE_PCI, 8,
+ pci_quirk_nvidia_tegra_disable_rp_msi);
+DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x1ad2,
+ PCI_CLASS_BRIDGE_PCI, 8,
+ pci_quirk_nvidia_tegra_disable_rp_msi);
+DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x0bf0,
+ PCI_CLASS_BRIDGE_PCI, 8,
+ pci_quirk_nvidia_tegra_disable_rp_msi);
+DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x0bf1,
+ PCI_CLASS_BRIDGE_PCI, 8,
+ pci_quirk_nvidia_tegra_disable_rp_msi);
+DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x0e1c,
+ PCI_CLASS_BRIDGE_PCI, 8,
+ pci_quirk_nvidia_tegra_disable_rp_msi);
+DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x0e1d,
+ PCI_CLASS_BRIDGE_PCI, 8,
+ pci_quirk_nvidia_tegra_disable_rp_msi);
+DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x0e12,
+ PCI_CLASS_BRIDGE_PCI, 8,
+ pci_quirk_nvidia_tegra_disable_rp_msi);
+DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x0e13,
+ PCI_CLASS_BRIDGE_PCI, 8,
+ pci_quirk_nvidia_tegra_disable_rp_msi);
+DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x0fae,
+ PCI_CLASS_BRIDGE_PCI, 8,
+ pci_quirk_nvidia_tegra_disable_rp_msi);
+DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x0faf,
+ PCI_CLASS_BRIDGE_PCI, 8,
+ pci_quirk_nvidia_tegra_disable_rp_msi);
+DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x10e5,
+ PCI_CLASS_BRIDGE_PCI, 8,
+ pci_quirk_nvidia_tegra_disable_rp_msi);
+DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x10e6,
+ PCI_CLASS_BRIDGE_PCI, 8,
+ pci_quirk_nvidia_tegra_disable_rp_msi);
+
/*
* Some versions of the MCP55 bridge from Nvidia have a legacy IRQ routing
* config register. This register controls the routing of legacy
--
2.17.1
^ permalink raw reply related
* [PATCH V13 01/12] PCI: Add #defines for some of PCIe spec r4.0 features
From: Vidya Sagar @ 2019-07-10 6:22 UTC (permalink / raw)
To: lorenzo.pieralisi, bhelgaas, robh+dt, mark.rutland,
thierry.reding, jonathanh, kishon, catalin.marinas, will.deacon,
jingoohan1, gustavo.pimentel
Cc: digetx, mperttunen, linux-pci, devicetree, linux-tegra,
linux-kernel, linux-arm-kernel, kthota, mmaddireddy, vidyas,
sagar.tv
In-Reply-To: <20190710062212.1745-1-vidyas@nvidia.com>
Add #defines only for the Data Link Feature and Physical Layer 16.0 GT/s
features as defined in PCIe spec r4.0, sec 7.7.4 for Data Link Feature and
sec 7.7.5 for Physical Layer 16.0 GT/s.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
---
V13:
* Updated commit message to include references from spec
* Removed unused defines and moved some from pcie-tegra194.c file
* Addressed review comments from Bjorn
V12:
* None
V11:
* None
V10:
* None
V9:
* None
V8:
* None
V7:
* None
V6:
* None
V5:
* None
V4:
* None
V3:
* Updated commit message and description to explicitly mention that defines are
added only for some of the features and not all.
V2:
* None
include/uapi/linux/pci_regs.h | 14 +++++++++++++-
1 file changed, 13 insertions(+), 1 deletion(-)
diff --git a/include/uapi/linux/pci_regs.h b/include/uapi/linux/pci_regs.h
index f28e562d7ca8..d28d0319d932 100644
--- a/include/uapi/linux/pci_regs.h
+++ b/include/uapi/linux/pci_regs.h
@@ -713,7 +713,9 @@
#define PCI_EXT_CAP_ID_DPC 0x1D /* Downstream Port Containment */
#define PCI_EXT_CAP_ID_L1SS 0x1E /* L1 PM Substates */
#define PCI_EXT_CAP_ID_PTM 0x1F /* Precision Time Measurement */
-#define PCI_EXT_CAP_ID_MAX PCI_EXT_CAP_ID_PTM
+#define PCI_EXT_CAP_ID_DLF 0x25 /* Data Link Feature */
+#define PCI_EXT_CAP_ID_PL_16GT 0x26 /* Physical Layer 16.0 GT/s */
+#define PCI_EXT_CAP_ID_MAX PCI_EXT_CAP_ID_PL_16GT
#define PCI_EXT_CAP_DSN_SIZEOF 12
#define PCI_EXT_CAP_MCAST_ENDPOINT_SIZEOF 40
@@ -1053,4 +1055,14 @@
#define PCI_L1SS_CTL1_LTR_L12_TH_SCALE 0xe0000000 /* LTR_L1.2_THRESHOLD_Scale */
#define PCI_L1SS_CTL2 0x0c /* Control 2 Register */
+/* Data Link Feature */
+#define PCI_DLF_CAP 0x04 /* Capabilities Register */
+#define PCI_DLF_EXCHANGE_ENABLE 0x80000000 /* Data Link Feature Exchange Enable */
+
+/* Physical Layer 16.0 GT/s */
+#define PCI_PL_16GT_LE_CTRL 0x20 /* Lane Equalization Control Register */
+#define PCI_PL_16GT_LE_CTRL_DSP_TX_PRESET_MASK 0x0000000F
+#define PCI_PL_16GT_LE_CTRL_USP_TX_PRESET_MASK 0x000000F0
+#define PCI_PL_16GT_LE_CTRL_USP_TX_PRESET_SHIFT 4
+
#endif /* LINUX_PCI_REGS_H */
--
2.17.1
^ permalink raw reply related
* [PATCH V13 00/12] PCI: tegra: Add Tegra194 PCIe support
From: Vidya Sagar @ 2019-07-10 6:22 UTC (permalink / raw)
To: lorenzo.pieralisi, bhelgaas, robh+dt, mark.rutland,
thierry.reding, jonathanh, kishon, catalin.marinas, will.deacon,
jingoohan1, gustavo.pimentel
Cc: digetx, mperttunen, linux-pci, devicetree, linux-tegra,
linux-kernel, linux-arm-kernel, kthota, mmaddireddy, vidyas,
sagar.tv
Tegra194 has six PCIe controllers based on Synopsys DesignWare core.
There are two Universal PHY (UPHY) blocks with each supporting 12(HSIO:
Hisg Speed IO) and 8(NVHS: NVIDIA High Speed) lanes respectively.
Controllers:0~4 use UPHY lanes from HSIO brick whereas Controller:5 uses
UPHY lanes from NVHS brick. Lane mapping in HSIO UPHY brick to each PCIe
controller (0~4) is controlled in XBAR module by BPMP-FW. Since PCIe
core has PIPE interface, a glue module called PIPE-to-UPHY (P2U) is used
to connect each UPHY lane (applicable to both HSIO and NVHS UPHY bricks)
to PCIe controller
This patch series
- Adds support for P2U PHY driver
- Adds support for PCIe host controller
- Adds device tree nodes each PCIe controllers
- Enables nodes applicable to p2972-0000 platform
- Adds helper APIs in Designware core driver to get capability regs offset
- Adds defines for new feature registers of PCIe spec revision 4
- Makes changes in DesignWare core driver to get Tegra194 PCIe working
Testing done on P2972-0000 platform
- Able to get PCIe link up with on-board Marvel eSATA controller
- Able to get PCIe link up with NVMe cards connected to M.2 Key-M slot
- Able to do data transfers with both SATA drives and NVMe cards
Note
- Enabling x8 slot on P2972-0000 platform requires pinmux driver for Tegra194.
It is being worked on currently and hence Controller:5 (i.e. x8 slot) is
disabled in this patch series. A future patch series would enable this.
- This series is based on top of the following series
Jisheng's patches to add support to .remove() in Designware sub-system
https://patchwork.kernel.org/project/linux-pci/list/?series=98559
(Update: Jisheng's patches are now accepted and applied for v5.2)
My patches made on top of Jisheng's patches to export various symbols
http://patchwork.ozlabs.org/project/linux-pci/list/?series=115671
(Update: My above patch series is accepted and applied for v5.3)
V13:
* Addressed Bjorn's review comments for adding Gen-4 specific defines to pci_regs.h header file
V12:
* Modified the commit message of patch-3 in this series to address review
comments from Lorenzo
V11:
* Removed device-tree patches from the series as they are applied to relevant
Tegra specific trees by Thierry Reding.
* Included older Tegra chips to extend quirk that disables MSI interrupt being
used for Tegra PCIe root ports.
* Addressed review comments in P2U driver file.
V10:
* Used _relaxed() versions of readl() & writel()
V9:
* Made the drivers dependent on ARCH_TEGRA_194_SOC directly
* Addressed review comments from Dmitry
V8:
* Changed P2U driver file name from pcie-p2u-tegra194.c to phy-tegra194-p2u.c
* Addressed review comments from Thierry and Rob
V7:
* Took care of review comments from Rob
* Added a quirk to disable MSI for root ports
* Removed using pcie_pme_disable_msi() API in host controller driver
V6:
* Removed patch that exports pcie_bus_config symbol
* Took care of review comments from Thierry and Rob
V5:
* Removed redundant APIs in pcie-designware-ep.c file after moving them
to pcie-designware.c file based on Bjorn's review comments
V4:
* Rebased on top of linux-next top of the tree
* Addressed Gustavo's comments and added his Ack for some of the changes.
V3:
* Addressed review comments from Thierry
V2:
* Addressed review comments from Bjorn, Thierry, Jonathan, Rob & Kishon
* Added more patches in v2 series
Vidya Sagar (12):
PCI: Add #defines for some of PCIe spec r4.0 features
PCI: Disable MSI for Tegra root ports
PCI: dwc: Perform dbi regs write lock towards the end
PCI: dwc: Move config space capability search API
PCI: dwc: Add ext config space capability search API
dt-bindings: PCI: designware: Add binding for CDM register check
PCI: dwc: Add support to enable CDM register check
dt-bindings: Add PCIe supports-clkreq property
dt-bindings: PCI: tegra: Add device tree support for Tegra194
dt-bindings: PHY: P2U: Add Tegra194 P2U block
phy: tegra: Add PCIe PIPE2UPHY support
PCI: tegra: Add Tegra194 PCIe support
.../bindings/pci/designware-pcie.txt | 5 +
.../bindings/pci/nvidia,tegra194-pcie.txt | 155 ++
Documentation/devicetree/bindings/pci/pci.txt | 5 +
.../bindings/phy/phy-tegra194-p2u.txt | 28 +
drivers/pci/controller/dwc/Kconfig | 10 +
drivers/pci/controller/dwc/Makefile | 1 +
.../pci/controller/dwc/pcie-designware-ep.c | 37 +-
.../pci/controller/dwc/pcie-designware-host.c | 14 +-
drivers/pci/controller/dwc/pcie-designware.c | 87 +
drivers/pci/controller/dwc/pcie-designware.h | 12 +
drivers/pci/controller/dwc/pcie-tegra194.c | 1632 +++++++++++++++++
drivers/pci/quirks.c | 53 +
drivers/phy/tegra/Kconfig | 7 +
drivers/phy/tegra/Makefile | 1 +
drivers/phy/tegra/phy-tegra194-p2u.c | 120 ++
include/uapi/linux/pci_regs.h | 14 +-
16 files changed, 2139 insertions(+), 42 deletions(-)
create mode 100644 Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt
create mode 100644 Documentation/devicetree/bindings/phy/phy-tegra194-p2u.txt
create mode 100644 drivers/pci/controller/dwc/pcie-tegra194.c
create mode 100644 drivers/phy/tegra/phy-tegra194-p2u.c
--
2.17.1
^ permalink raw reply
* Re: [PATCH V12 01/12] PCI: Add #defines for some of PCIe spec r4.0 features
From: Vidya Sagar @ 2019-07-10 5:18 UTC (permalink / raw)
To: Bjorn Helgaas
Cc: lorenzo.pieralisi, robh+dt, mark.rutland, thierry.reding,
jonathanh, kishon, catalin.marinas, will.deacon, jingoohan1,
gustavo.pimentel, digetx, mperttunen, linux-pci, devicetree,
linux-tegra, linux-kernel, linux-arm-kernel, kthota, mmaddireddy,
sagar.tv
In-Reply-To: <20190709141427.GB35486@google.com>
On 7/9/2019 7:44 PM, Bjorn Helgaas wrote:
> On Mon, Jul 01, 2019 at 06:09:59PM +0530, Vidya Sagar wrote:
>> Add #defines only for the Data Link Feature and Physical Layer 16.0 GT/s
>> features.
>>
>> Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
>> Reviewed-by: Thierry Reding <treding@nvidia.com>
>
> Please include spec references in the commit log, e.g., PCIe r5.0, sec
> 7.7.4, for Data Link Feature and sec 7.7.5 for Physical Layer 16 GT/s.
Done.
>
>> include/uapi/linux/pci_regs.h | 22 +++++++++++++++++++++-
>> 1 file changed, 21 insertions(+), 1 deletion(-)
>>
>> diff --git a/include/uapi/linux/pci_regs.h b/include/uapi/linux/pci_regs.h
>> index f28e562d7ca8..1c79f6a097d2 100644
>> --- a/include/uapi/linux/pci_regs.h
>> +++ b/include/uapi/linux/pci_regs.h
>> @@ -713,7 +713,9 @@
>> #define PCI_EXT_CAP_ID_DPC 0x1D /* Downstream Port Containment */
>> #define PCI_EXT_CAP_ID_L1SS 0x1E /* L1 PM Substates */
>> #define PCI_EXT_CAP_ID_PTM 0x1F /* Precision Time Measurement */
>> -#define PCI_EXT_CAP_ID_MAX PCI_EXT_CAP_ID_PTM
>> +#define PCI_EXT_CAP_ID_DLF 0x25 /* Data Link Feature */
>> +#define PCI_EXT_CAP_ID_PL 0x26 /* Physical Layer 16.0 GT/s */
>
> Maybe PCI_EXT_CAP_ID_PL_16GT so there's a little more hint of what
> this is for?
Ok. I'll add 16GT.
>
>> +#define PCI_EXT_CAP_ID_MAX PCI_EXT_CAP_ID_PL
>>
>> #define PCI_EXT_CAP_DSN_SIZEOF 12
>> #define PCI_EXT_CAP_MCAST_ENDPOINT_SIZEOF 40
>> @@ -1053,4 +1055,22 @@
>> #define PCI_L1SS_CTL1_LTR_L12_TH_SCALE 0xe0000000 /* LTR_L1.2_THRESHOLD_Scale */
>> #define PCI_L1SS_CTL2 0x0c /* Control 2 Register */
>>
>> +/* Data Link Feature */
>> +#define PCI_DLF_CAP 0x04 /* Capabilities Register */
>> +#define PCI_DLF_LOCAL_DLF_SUP_MASK 0x007fffff /* Local Data Link Feature Supported */
>> +#define PCI_DLF_EXCHANGE_ENABLE 0x80000000 /* Data Link Feature Exchange Enable */
>> +#define PCI_DLF_STS 0x08 /* Status Register */
>> +#define PCI_DLF_REMOTE_DLF_SUP_MASK 0x007fffff /* Remote Data Link Feature Supported */
>> +#define PCI_DLF_REMOTE_DLF_SUP_VALID 0x80000000 /* Remote Data Link Feature Support Valid */
>
> I'm a little bit ambivalent about adding #defines that aren't used. I
> personally would probably just add the things we use, so the header
> file gives a clue about what's currently implemented. But I guess
> either way is fine.
Fine. I'll remove all unused defines in the next patch.
>
>> +/* Physical Layer 16.0 GT/s */
>> +#define PCI_PL_16GT_CAP 0x04 /* Capabilities Register */
>> +#define PCI_PL_16GT_CTRL 0x08 /* Control Register */
>> +#define PCI_PL_16GT_STS 0x0c /* Status Register */
>> +#define PCI_PL_16GT_LDPM_STS 0x10 /* Local Data Parity Mismatch Status Register */
>> +#define PCI_PL_16GT_FRDPM_STS 0x14 /* First Retimer Data Parity Mismatch Status Register */
>> +#define PCI_PL_16GT_SRDPM_STS 0x18 /* Second Retimer Data Parity Mismatch Status Register */
>> +#define PCI_PL_16GT_RSVD 0x1C /* Reserved */
>
> Use lower-case hex consistently here. There's no global consistency
> in this file, but we can at least be consistent in each section. But
> I'm even more hesitant about included unused #defines for "reserved"
> fields, so if you drop this it would take care of both :)
Done.
>
>> +#define PCI_PL_16GT_LE_CTRL 0x20 /* Lane Equalization Control Register */
>
> This is the only register you actually use. You defined a local
> PL16G_CAP_OFF_DSP_16G_TX_PRESET_MASK for this register. Shouldn't
> that be defined here instead of in
> drivers/pci/controller/dwc/pcie-tegra194.c?
I'll take care of it in the next patch.
>
>> #endif /* LINUX_PCI_REGS_H */
>> --
>> 2.17.1
>>
^ permalink raw reply
* Re: [PATCH v2 05/10] net: hisilicon: HI13X1_GMAX need dreq reset at first
From: Jiangfeng Xiao @ 2019-07-10 5:05 UTC (permalink / raw)
To: Sergei Shtylyov, davem, robh+dt, yisen.zhuang, salil.mehta,
mark.rutland, dingtianhong
Cc: netdev, devicetree, linux-kernel, leeyou.li, nixiaoming,
jianping.liu, xiekunxun
In-Reply-To: <101b8c68-75f5-00a7-9845-e59c0467768c@huawei.com>
On 2019/7/9 21:48, Jiangfeng Xiao wrote:
>
>
> On 2019/7/9 17:35, Sergei Shtylyov wrote:
>> Hello!
>>
>> On 09.07.2019 6:31, Jiangfeng Xiao wrote:
>>
[...]
>>> @@ -853,6 +867,15 @@ static int hip04_mac_probe(struct platform_device *pdev)
>>> goto init_fail;
>>> }
>>> +#if defined(CONFIG_HI13X1_GMAC)
>>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
>>> + priv->sysctrl_base = devm_ioremap_resource(d, res);
>>
>> There's devm_platform_ioremap_resource() now.
>
> Thank you for your review, Great issue, which makes my code more concise.
>
> I will fix it in v3. Or submit a patch to modify it separately, if maintainer
> applies this patch series.
>
I decided to wait for this series of patches to sync to the mainline
and then fix this based on the mainline.
Because the mainline does not currently have this part of the code,
if I submit the changes, and the patch is accidentally merged into
another branch or another maintainer to handle, a conflict will occur.
As we all know, maintianer has to deal with many commits every day,
I don't want to increase the burden of maintainer.
So I decided to wait until the patch is synced to the mainline
and then modify it, which is more safe.
^ permalink raw reply
* Re: [PATCH 1/2] dt-bindings: milbeaut-m10v-hdmac: Add Socionext Milbeaut HDMAC bindings
From: Jassi Brar @ 2019-07-10 4:12 UTC (permalink / raw)
To: Rob Herring
Cc: dmaengine, Devicetree List, Linux Kernel Mailing List, vkoul,
Mark Rutland, orito.takao, Masami Hiramatsu, kasai.kazuhiro,
Jassi Brar
In-Reply-To: <20190709143437.GA30850@bogus>
On Tue, Jul 9, 2019 at 9:34 AM Rob Herring <robh@kernel.org> wrote:
>
> On Wed, Jun 12, 2019 at 07:52:37PM -0500, jassisinghbrar@gmail.com wrote:
> > From: Jassi Brar <jaswinder.singh@linaro.org>
> >
> > Document the devicetree bindings for Socionext Milbeaut HDMAC
> > controller. Controller has upto 8 floating channels, that need
> > a predefined slave-id to work from a set of slaves.
> >
> > Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
> > ---
> > .../bindings/dma/milbeaut-m10v-hdmac.txt | 54 +++++++++++++++++++
> > 1 file changed, 54 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/dma/milbeaut-m10v-hdmac.txt
> >
> > diff --git a/Documentation/devicetree/bindings/dma/milbeaut-m10v-hdmac.txt b/Documentation/devicetree/bindings/dma/milbeaut-m10v-hdmac.txt
> > new file mode 100644
> > index 000000000000..a104fcb9e73d
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/dma/milbeaut-m10v-hdmac.txt
> > @@ -0,0 +1,51 @@
> > +* Milbeaut AHB DMA Controller
> > +
> > +Milbeaut AHB DMA controller has transfer capability bellow.
> > + - memory to memory transfer
> > + - device to memory transfer
> > + - memory to device transfer
> > +
> > +Required property:
> > +- compatible: Should be "socionext,milbeaut-m10v-hdmac"
> > +- reg: Should contain DMA registers location and length.
> > +- interrupts: Should contain all of the per-channel DMA interrupts.
>
> How many?
>
Each channel has an IRQ line. And the number of channels is
configurable. So instead of having some explicit property like
'dma-channels', we infer that from the number of irqs registered.
> > +- #dma-cells: Should be 1. Specify the ID of the slave.
> > +- clocks: Phandle to the clock used by the HDMAC module.
> > +
> > +
> > +Example:
> > +
> > + hdmac1: hdmac@1e110000 {
>
> dma-controller@...
>
OK
> > + compatible = "socionext,milbeaut-m10v-hdmac";
> > + reg = <0x1e110000 0x10000>;
> > + interrupts = <0 132 4>,
> > + <0 133 4>,
> > + <0 134 4>,
> > + <0 135 4>,
> > + <0 136 4>,
> > + <0 137 4>,
> > + <0 138 4>,
> > + <0 139 4>;
> > + #dma-cells = <1>;
> > + clocks = <&dummy_clk>;
> > + };
> > +
> > +* DMA client
> > +
> > +Clients have to specify the DMA requests with phandles in a list.
>
> Nothing specific to this binding here and the client side is already
> documented, so drop this section.
>
OK.
Thanks
^ permalink raw reply
* Re: [PATCH 5/7] ASoC: rockchip: rockchip-max98090: Add node for HDMI
From: Cheng-yi Chiang @ 2019-07-10 4:11 UTC (permalink / raw)
To: Rob Herring
Cc: linux-kernel, Hans Verkuil, Bartlomiej Zolnierkiewicz,
Greg Kroah-Hartman, Philipp Zabel, Mark Brown, Liam Girdwood,
Takashi Iwai, Jaroslav Kysela, Russell King, Andrzej Hajda,
Laurent Pinchart, David Airlie, Daniel Vetter, Heiko Stuebner,
Doug Anderson, Dylan Reid, tzungbi, linux-media, SOUND
In-Reply-To: <20190709200121.GA19118@bogus>
On Wed, Jul 10, 2019 at 4:01 AM Rob Herring <robh@kernel.org> wrote:
>
> On Mon, Jun 03, 2019 at 12:32:49PM +0800, Cheng-Yi Chiang wrote:
> > Let user specify HDMI node so machine driver can use it to let codec
> > driver register callback on correct hdmi-notifier.
> >
> > Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
> > ---
> > Documentation/devicetree/bindings/sound/rockchip-max98090.txt | 2 ++
> > 1 file changed, 2 insertions(+)
> >
> > diff --git a/Documentation/devicetree/bindings/sound/rockchip-max98090.txt b/Documentation/devicetree/bindings/sound/rockchip-max98090.txt
> > index a805aa99ad75..dae57c14864e 100644
> > --- a/Documentation/devicetree/bindings/sound/rockchip-max98090.txt
> > +++ b/Documentation/devicetree/bindings/sound/rockchip-max98090.txt
> > @@ -7,6 +7,7 @@ Required properties:
> > connected to the CODEC
> > - rockchip,audio-codec: The phandle of the MAX98090 audio codec
> > - rockchip,headset-codec: The phandle of Ext chip for jack detection
> > +- rockchip,hdmi: The phandle of HDMI node for HDMI jack detection
> >
> > Example:
> >
> > @@ -16,4 +17,5 @@ sound {
> > rockchip,i2s-controller = <&i2s>;
> > rockchip,audio-codec = <&max98090>;
> > rockchip,headset-codec = <&headsetcodec>;
> > + rockchip,hdmi= <&hdmi>;
>
> space ^
>
> With that,
>
> Acked-by: Rob Herring <robh@kernel.org>
>
Hi Rob,
Thank you for the review.
But I have changed the approach in v2 so there is no need for machine
driver to expose this property.
Thanks!
> > };
> > --
> > 2.22.0.rc1.257.g3120a18244-goog
> >
^ permalink raw reply
* Re: [PATCH v7 06/18] kbuild: enable building KUnit
From: Masahiro Yamada @ 2019-07-10 3:59 UTC (permalink / raw)
To: Brendan Higgins
Cc: Frank Rowand, Greg Kroah-Hartman, Josh Poimboeuf, Kees Cook,
Kieran Bingham, Luis R. Rodriguez, Peter Zijlstra (Intel),
Rob Herring, Stephen Boyd, Cc: Shuah Khan, Theodore Ts'o,
DTML, dri-devel, kunit-dev, open list:DOCUMENTATION,
linux-fsdevel, Linux Kbuild mailing list,
Linux Kernel Mailing List, KERNEL
In-Reply-To: <20190709063023.251446-7-brendanhiggins@google.com>
On Tue, Jul 9, 2019 at 3:34 PM Brendan Higgins
<brendanhiggins@google.com> wrote:
>
> KUnit is a new unit testing framework for the kernel and when used is
> built into the kernel as a part of it. Add KUnit to the root Kconfig and
> Makefile to allow it to be actually built.
>
> Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
> Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
> Cc: Michal Marek <michal.lkml@markovi.net>
> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
> Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
> ---
> Kconfig | 2 ++
> Makefile | 2 +-
> 2 files changed, 3 insertions(+), 1 deletion(-)
>
> diff --git a/Kconfig b/Kconfig
> index 48a80beab6853..10428501edb78 100644
> --- a/Kconfig
> +++ b/Kconfig
> @@ -30,3 +30,5 @@ source "crypto/Kconfig"
> source "lib/Kconfig"
>
> source "lib/Kconfig.debug"
> +
> +source "kunit/Kconfig"
> diff --git a/Makefile b/Makefile
> index 3e4868a6498b2..60cf4f0813e0d 100644
> --- a/Makefile
> +++ b/Makefile
> @@ -991,7 +991,7 @@ endif
> PHONY += prepare0
>
> ifeq ($(KBUILD_EXTMOD),)
> -core-y += kernel/ certs/ mm/ fs/ ipc/ security/ crypto/ block/
> +core-y += kernel/ certs/ mm/ fs/ ipc/ security/ crypto/ block/ kunit/
>
> vmlinux-dirs := $(patsubst %/,%,$(filter %/, $(init-y) $(init-m) \
> $(core-y) $(core-m) $(drivers-y) $(drivers-m) \
> --
> 2.22.0.410.gd8fdbe21b5-goog
This is so trivial, and do not need to get ack from me.
Just a nit.
When CONFIG_KUNIT is disable, is there any point in descending into kunit/ ?
core-$(CONFIG_KUNIT) += kunit/
... might be useful to skip kunit/ entirely.
If you look at the top-level Makefile, some entries are doing this:
init-y := init/
drivers-y := drivers/ sound/
drivers-$(CONFIG_SAMPLES) += samples/
drivers-$(CONFIG_KERNEL_HEADER_TEST) += include/
net-y := net/
libs-y := lib/
core-y := usr/
--
Best Regards
Masahiro Yamada
^ permalink raw reply
* Re: [PATCH v7 08/18] objtool: add kunit_try_catch_throw to the noreturn list
From: Josh Poimboeuf @ 2019-07-10 2:31 UTC (permalink / raw)
To: Brendan Higgins
Cc: frowand.list, gregkh, keescook, kieran.bingham, mcgrof, peterz,
robh, sboyd, shuah, tytso, yamada.masahiro, devicetree, dri-devel,
kunit-dev, linux-doc, linux-fsdevel, linux-kbuild, linux-kernel,
linux-kselftest, linux-nvdimm, linux-um, Alexander.Levin,
Tim.Bird, amir73il, dan.carpenter, daniel, jdike, joel,
julia.lawall, khilman, knut.omang, logang, mpe
In-Reply-To: <20190709063023.251446-9-brendanhiggins@google.com>
On Mon, Jul 08, 2019 at 11:30:13PM -0700, Brendan Higgins wrote:
> Fix the following warning seen on GCC 7.3:
> kunit/test-test.o: warning: objtool: kunit_test_unsuccessful_try() falls through to next function kunit_test_catch()
>
> kunit_try_catch_throw is a function added in the following patch in this
> series; it allows KUnit, a unit testing framework for the kernel, to
> bail out of a broken test. As a consequence, it is a new __noreturn
> function that objtool thinks is broken (as seen above). So fix this
> warning by adding kunit_try_catch_throw to objtool's noreturn list.
>
> Reported-by: kbuild test robot <lkp@intel.com>
> Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
> Link: https://www.spinics.net/lists/linux-kbuild/msg21708.html
> Cc: Josh Poimboeuf <jpoimboe@redhat.com>
> Cc: Peter Zijlstra <peterz@infradead.org>
> ---
> tools/objtool/check.c | 1 +
> 1 file changed, 1 insertion(+)
>
> diff --git a/tools/objtool/check.c b/tools/objtool/check.c
> index 172f991957269..98db5fe85c797 100644
> --- a/tools/objtool/check.c
> +++ b/tools/objtool/check.c
> @@ -134,6 +134,7 @@ static int __dead_end_function(struct objtool_file *file, struct symbol *func,
> "usercopy_abort",
> "machine_real_restart",
> "rewind_stack_do_exit",
> + "kunit_try_catch_throw",
> };
>
> if (func->bind == STB_WEAK)
> --
> 2.22.0.410.gd8fdbe21b5-goog
>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
--
Josh
^ permalink raw reply
* Re: [linux,dev-5.1 v1] dt-bindings: gpio: aspeed: Add SGPIO support
From: Andrew Jeffery @ 2019-07-10 2:16 UTC (permalink / raw)
To: Hongwei Zhang, devicetree, Joel Stanley, Linus Walleij
Cc: Rob Herring, Mark Rutland, linux-aspeed, linux-kernel
In-Reply-To: <1562184069-22332-1-git-send-email-hongweiz@ami.com>
On Thu, 4 Jul 2019, at 05:31, Hongwei Zhang wrote:
> Add bindings to support SGPIO on AST2400 or AST2500.
>
> Signed-off-by: Hongwei Zhang <hongweiz@ami.com>
> ---
> .../devicetree/bindings/gpio/sgpio-aspeed.txt | 36 ++++++++++++++++++++++
> 1 file changed, 36 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/gpio/sgpio-aspeed.txt
>
> diff --git a/Documentation/devicetree/bindings/gpio/sgpio-aspeed.txt
> b/Documentation/devicetree/bindings/gpio/sgpio-aspeed.txt
> new file mode 100644
> index 0000000..f5fc6ef
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/gpio/sgpio-aspeed.txt
> @@ -0,0 +1,36 @@
> +Aspeed SGPIO controller Device Tree Bindings
> +-------------------------------------------
> +
> +Required properties:
> +- compatible : Either "aspeed,ast2400-sgpio" or "aspeed,ast2500-sgpio"
> +
> +- #gpio-cells : Should be two
> + - First cell is the GPIO line number
> + - Second cell is used to specify optional
> + parameters (unused)
> +
> +- reg : Address and length of the register set for the device
> +- gpio-controller : Marks the device node as a GPIO controller.
> +- interrupts : Interrupt specifier (see interrupt bindings for
> + details)
> +- interrupt-controller : Mark the GPIO controller as an
> interrupt-controller
As this is a serial GPIO controller, a critical piece of configuration
information is how many GPIOs we wish to serialise. This is done
in multiples of 8, up to 80 pins.
The bindings need to describe the "ngpios" property from the
generic GPIO bindings and how this affects the behaviour of
the controller.
We also need to add the "bus-frequency" property here to control
the rate of SGPMCK.
> +
> +Optional properties:
> +
> +- clocks : A phandle to the clock to use for debounce
> timings
We need this, but not for the reason specified, and it should be a
required property. We need PCLK (the APB clock) to derive the SGPIO
bus frequency. Despite what the datasheet blurb says, there's no
debounce control for the SGPIO master (this is a copy/paste mistake
from the description of the parallel GPIO master).
> +
> +The sgpio and interrupt properties are further described in their
> respective
> +bindings documentation:
> +
> +- Documentation/devicetree/bindings/sgpio/gpio.txt
> +- Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
> +
> + Example:
> + sgpio@1e780200 {
> + #gpio-cells = <2>;
> + compatible = "aspeed,ast2500-sgpio";
> + gpio-controller;
> + interrupts = <40>;
> + reg = <0x1e780200 0x0100>;
> + interrupt-controller;
> + };
You'll need to fix up the example after making the changes mentioned
above.
Andrew
> --
> 2.7.4
>
>
^ permalink raw reply
* Re: [linux,dev-5.1 v1] dt-bindings: gpio: aspeed: Add SGPIO support
From: Andrew Jeffery @ 2019-07-10 2:00 UTC (permalink / raw)
To: Rob Herring, Hongwei Zhang
Cc: devicetree, Joel Stanley, Linus Walleij, Mark Rutland,
linux-aspeed, linux-kernel@vger.kernel.org
In-Reply-To: <CAL_Jsq+0z4OZ7qbaiUva1v5xCKXpsaPBZ9tj_M4HbEihsU_MfA@mail.gmail.com>
On Wed, 10 Jul 2019, at 04:23, Rob Herring wrote:
> On Wed, Jul 3, 2019 at 2:01 PM Hongwei Zhang <hongweiz@ami.com> wrote:
> >
> > Add bindings to support SGPIO on AST2400 or AST2500.
> >
> > Signed-off-by: Hongwei Zhang <hongweiz@ami.com>
> > ---
> > .../devicetree/bindings/gpio/sgpio-aspeed.txt | 36 ++++++++++++++++++++++
>
> Is this SGPIO as in the blinky lights for HDDs in servers? If so, that
> has nothing to do with Linux GPIO subsystem.
>
No, this is just literal serialised GPIO, which can be used with e.g. nexperia
74LV595 / 74LV165 parts.
There is a separate chunk of IP in the SoC that acts as an SFF-8485 (blinky
lights) slave monitor.
Andrew
^ permalink raw reply
* RE: [PATCH V4 2/5] clocksource/drivers/sysctr: Add clock-frequency property
From: Anson Huang @ 2019-07-10 1:30 UTC (permalink / raw)
To: Rob Herring
Cc: Daniel Lezcano, Thomas Gleixner, Mark Rutland, Shawn Guo,
Sascha Hauer, Sascha Hauer, Fabio Estevam, Leonard Crestez,
Viresh Kumar, Daniel Baluta, Jacky Bai, Lucas Stach, Abel Vesa,
Andrey Smirnov, Carlo Caione, Angus Ainslie (Purism),
Guido Günther, linux-kernel@vger.kernel.org, devicetree
In-Reply-To: <CAL_JsqKeu-b8mbMJBtnNn1vL=RSvUXbo+g40haZnjXTW11CJ6w@mail.gmail.com>
Hi, Rob
> On Mon, Jul 1, 2019 at 3:47 AM <Anson.Huang@nxp.com> wrote:
> >
> > From: Anson Huang <Anson.Huang@nxp.com>
>
> 'dt-bindings: timer: ...' for the subject.
OK, I made a mistake.
>
> >
> > Systems which use platform driver model for clock driver require the
> > clock frequency to be supplied via device tree when system counter
> > driver is enabled.
>
> This is a DT binding. What's a platform driver?
It is just trying to explain why we need to introduce this "clock-frequency"
property, nothing about the binding and platform driver.
>
> >
> > This is necessary as in the platform driver model the of_clk
> > operations do not work correctly because system counter driver is
> > initialized in early phase of system boot up, and clock driver using
> > platform driver model is NOT ready at that time, it will cause system
> > counter driver initialization failed.
> >
> > Add clock-frequency property to the device tree bindings of the NXP
> > system counter, so the driver can tell timer-of driver to get clock
> > frequency from DT directly instead of doing of_clk operations via clk
> > APIs.
>
> While you've now given a good explanation why you need this, it all sounds
> like linux specific issues and a DT change should not be necessary.
>
> Presumably, 'clocks' points to a fixed-clock node, right? Just parse the 'clocks'
> phandle and fetch the frequency from that node if you need to get the
> frequency 'early'.
Sound like a better solution, I will try that, since the system counter's clock is
from osc_24m and divided by 3, since different platforms may have different divider,
so maybe I can create a fixed-clock node in DT, then system counter driver can parse
the clock and fetch the frequency from that node, will redo a V5 patch.
>
> > Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
> > ---
> > No change.
> > ---
> > .../devicetree/bindings/timer/nxp,sysctr-timer.txt | 15 +++++++++------
> > 1 file changed, 9 insertions(+), 6 deletions(-)
> >
> > diff --git
> > a/Documentation/devicetree/bindings/timer/nxp,sysctr-timer.txt
> > b/Documentation/devicetree/bindings/timer/nxp,sysctr-timer.txt
> > index d576599..7088a0e 100644
> > --- a/Documentation/devicetree/bindings/timer/nxp,sysctr-timer.txt
> > +++ b/Documentation/devicetree/bindings/timer/nxp,sysctr-timer.txt
> > @@ -11,15 +11,18 @@ Required properties:
> > - reg : Specifies the base physical address and size of the comapre
> > frame and the counter control, read & compare.
> > - interrupts : should be the first compare frames' interrupt
> > -- clocks : Specifies the counter clock.
> > -- clock-names: Specifies the clock's name of this module
> > +- clocks : Specifies the counter clock, mutually exclusive with clock-
> frequency.
> > +- clock-names : Specifies the clock's name of this module, mutually
> exclusive with
> > + clock-frequency.
> > +- clock-frequency : Specifies system counter clock frequency, mutually
> exclusive with
> > + clocks/clock-names.
>
> It doesn't really work to say one or the other is needed unless you make the
> OS support both cases.
The OS already support both cases now with this patch series.
Thanks,
Anson
^ permalink raw reply
* Re: [PATCH v3] media: dt: bindings: tegra-vde: Document new optional IOMMU property
From: Rob Herring @ 2019-07-09 23:02 UTC (permalink / raw)
To: Dmitry Osipenko
Cc: Thierry Reding, Jonathan Hunter, Mauro Carvalho Chehab,
Hans Verkuil, linux-media, devicetree, linux-tegra, devel,
linux-kernel
In-Reply-To: <20190623170730.5095-4-digetx@gmail.com>
On Sun, 23 Jun 2019 20:07:26 +0300, Dmitry Osipenko wrote:
> All NVIDIA Tegra SoC generations provide IOMMU support for the video
> decoder engine. Document new optional device-tree property that connects
> VDE with the IOMMU provider.
>
> Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
> ---
>
> No changes since v1.
>
> Documentation/devicetree/bindings/media/nvidia,tegra-vde.txt | 2 ++
> 1 file changed, 2 insertions(+)
>
Reviewed-by: Rob Herring <robh@kernel.org>
^ permalink raw reply
* Re: [PATCH v3 7/9] dt-bindings: vendor-prefixes: add Sipeed
From: Rob Herring @ 2019-07-09 22:57 UTC (permalink / raw)
Cc: Maxime Ripard, Chen-Yu Tsai, Linus Walleij,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-clk-u79uwXL29TY76Z2rM5mHXA,
linux-gpio-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Icenowy Zheng
In-Reply-To: <20190623043801.14040-8-icenowy-h8G6r0blFSE@public.gmane.org>
On Sun, 23 Jun 2019 12:37:59 +0800, Icenowy Zheng wrote:
> Shenzhen Sipeed Technology Co., Ltd. is a company focused on development
> kits, which also contains rebranded Lichee Pi series.
>
> Add its vendor prefix binding.
>
> Signed-off-by: Icenowy Zheng <icenowy-h8G6r0blFSE@public.gmane.org>
> ---
> Changes in v3:
> - Rebased because of the addition of sinlinx and sinovoip.
>
> Patch introduced in v2.
>
> Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
> 1 file changed, 2 insertions(+)
>
Applied, thanks.
Rob
--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/Ez6ZCGd0@public.gmane.org
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20190709225744.GA25215%40bogus.
For more options, visit https://groups.google.com/d/optout.
^ permalink raw reply
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox