[PATCH V1 1/2] mmc:sdhci-pci-o2micro: Change implementation of tuning for SDR104 and HS200 mode

[PATCH V1 1/2] mmc:sdhci-pci-o2micro: Change implementation of tuning for SDR104 and HS200 mode

[fred]

Select DLL clock of output tuning
Select fixed output tuning phase 0x9

Signed-off-by: fred<fred.ai@bayhubtech.com>

---
Change in V1:
1. Set register 0x354 bit 16 to select DLL clock
2. Set register 0x354 bit [23:20] to select fiexd output tuning phase 0x9
---
 drivers/mmc/host/sdhci-pci-o2micro.c | 51 +++++++++++++++++++++++-----
 1 file changed, 42 insertions(+), 9 deletions(-)

diff --git a/drivers/mmc/host/sdhci-pci-o2micro.c b/drivers/mmc/host/sdhci-pci-o2micro.c
index f045c1ee4667..dfd447c1c367 100644
--- a/drivers/mmc/host/sdhci-pci-o2micro.c
+++ b/drivers/mmc/host/sdhci-pci-o2micro.c
@@ -43,6 +43,7 @@
 #define O2_SD_CAP_REG0		0x334
 #define O2_SD_UHS1_CAP_SETTING	0x33C
 #define O2_SD_DELAY_CTRL	0x350
+#define O2_SD_OUTPUT_CLK_SOURCE_SWITCH	0x354
 #define O2_SD_UHS2_L1_CTRL	0x35C
 #define O2_SD_FUNC_REG3		0x3E0
 #define O2_SD_FUNC_REG4		0x3E4
@@ -304,6 +305,11 @@ static int sdhci_o2_execute_tuning(struct mmc_host *mmc, u32 opcode)
 	int current_bus_width = 0;
 	u32 scratch32 = 0;
 	u16 scratch = 0;
+	u8  scratch_8 = 0;
+	u32 reg_val;
+	u8  dll_mode;
+	struct sdhci_pci_slot *slot = sdhci_priv(host);
+	struct sdhci_pci_chip *chip = slot->chip;
 
 	/*
 	 * This handler only implements the eMMC tuning that is specific to
@@ -322,6 +328,28 @@ static int sdhci_o2_execute_tuning(struct mmc_host *mmc, u32 opcode)
 	scratch |= O2_SD_PWR_FORCE_L0;
 	sdhci_writew(host, scratch, O2_SD_MISC_CTRL);
 
+	/*stop clk*/
+	reg_val = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
+	reg_val &= ~(SDHCI_CLOCK_CARD_EN);
+	sdhci_writew(host, reg_val, SDHCI_CLOCK_CONTROL);
+
+	/*UnLock WP*/
+	pci_read_config_byte(chip->pdev, O2_SD_LOCK_WP, &scratch_8);
+	scratch_8 &= 0x7f;
+	pci_write_config_byte(chip->pdev, O2_SD_LOCK_WP, scratch_8);
+
+	//Set pcr 0x354[16] to choose dll clock ,and set the default phase
+	dll_mode = 0x9; //set default phase 9
+	pci_read_config_dword(chip->pdev, O2_SD_OUTPUT_CLK_SOURCE_SWITCH, &reg_val);
+	reg_val &= 0xFF0EFFFF;
+	reg_val |= ((1 << 16) | (dll_mode << 20));
+	pci_write_config_dword(chip->pdev, O2_SD_OUTPUT_CLK_SOURCE_SWITCH, reg_val);
+
+    /*open clk*/
+	reg_val = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
+	reg_val |= SDHCI_CLOCK_CARD_EN;
+	sdhci_writew(host, reg_val, SDHCI_CLOCK_CONTROL);
+
 	/* wait DLL lock, timeout value 5ms */
 	if (readx_poll_timeout(sdhci_o2_pll_dll_wdt_control, host,
 		scratch32, (scratch32 & O2_DLL_LOCK_STATUS), 1, 5000))
@@ -532,24 +560,29 @@ static void sdhci_pci_o2_set_clock(struct sdhci_host *host, unsigned int clock)
 
 	if (clock == 0)
 		return;
+	/*UnLock WP*/
+	pci_read_config_byte(chip->pdev, O2_SD_LOCK_WP, &scratch);
+	scratch &= 0x7f;
+	pci_write_config_byte(chip->pdev, O2_SD_LOCK_WP, scratch);
 
 	if ((host->timing == MMC_TIMING_UHS_SDR104) && (clock == 200000000)) {
-		pci_read_config_byte(chip->pdev, O2_SD_LOCK_WP, &scratch);
-
-		scratch &= 0x7f;
-		pci_write_config_byte(chip->pdev, O2_SD_LOCK_WP, scratch);
-
 		pci_read_config_dword(chip->pdev, O2_SD_PLL_SETTING, &scratch_32);
 
 		if ((scratch_32 & 0xFFFF0000) != 0x2c280000)
 			o2_pci_set_baseclk(chip, 0x2c280000);
 
-		pci_read_config_byte(chip->pdev, O2_SD_LOCK_WP, &scratch);
-
-		scratch |= 0x80;
-		pci_write_config_byte(chip->pdev, O2_SD_LOCK_WP, scratch);
+		/*If not SDR104 card mode, set 0x354 value 0*/
+		pci_read_config_dword(chip->pdev, O2_SD_OUTPUT_CLK_SOURCE_SWITCH, &scratch_32);
+		scratch_32 &= ~(1 << 16);
+		scratch_32 &= ~(0xf << 20);
+		pci_write_config_dword(chip->pdev, O2_SD_OUTPUT_CLK_SOURCE_SWITCH,scratch_32);
 	}
 
+    /*Lock WP*/
+	pci_read_config_byte(chip->pdev, O2_SD_LOCK_WP, &scratch);
+	scratch |= 0x80;
+	pci_write_config_byte(chip->pdev, O2_SD_LOCK_WP, scratch);
+
 	clk = sdhci_calc_clk(host, clock, &host->mmc->actual_clock);
 	sdhci_o2_enable_clk(host, clk);
 }
-- 
2.32.0

[PATCH V1 2/2] mmc:sdhci-pci-o2micro:Change implementation of setting corresponding PLL frequency according to card mode

[fred]

1.SDR104 card mode PLL frequency is 0x2c28.
2.SD2.0/SDR50 card mode PLL frequency is 0X2510.

Signed-off-by: fred<fred.ai@bayhubtech.com>

change in v1:
When SD2.0/SDR50 card mode,driver need to set PLL frequency 0x2510.
---
 drivers/mmc/host/sdhci-pci-o2micro.c | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/drivers/mmc/host/sdhci-pci-o2micro.c b/drivers/mmc/host/sdhci-pci-o2micro.c
index bac3f0f8185b..32a8ef874efa 100644
--- a/drivers/mmc/host/sdhci-pci-o2micro.c
+++ b/drivers/mmc/host/sdhci-pci-o2micro.c
@@ -568,9 +568,17 @@ static void sdhci_pci_o2_set_clock(struct sdhci_host *host, unsigned int clock)
 	if ((host->timing == MMC_TIMING_UHS_SDR104) && (clock == 200000000)) {
 		pci_read_config_dword(chip->pdev, O2_SD_PLL_SETTING, &scratch_32);
 
+		/*SDR104 card mode PLL frequency value is 0x2c28*/
 		if ((scratch_32 & 0xFFFF0000) != 0x2c280000)
 			o2_pci_set_baseclk(chip, 0x2c280000);
 
+	} else {
+		pci_read_config_dword(chip->pdev, O2_SD_PLL_SETTING, &scratch_32);
+
+		/*SD2.0,SDR50 card mode PLL DMDN value is 0X2510*/
+		if ((scratch_32 & 0xFFFF0000) != 0x2510000)
+			o2_pci_set_baseclk(chip, 0x25100000);
+
 		/*If not SDR104 card mode, set 0x354 value 0*/
 		pci_read_config_dword(chip->pdev, O2_SD_OUTPUT_CLK_SOURCE_SWITCH, &scratch_32);
 		scratch_32 &= ~(1 << 16);
-- 
2.32.0

Re: [PATCH V1 2/2] mmc:sdhci-pci-o2micro:Change implementation of setting corresponding PLL frequency according to card mode

[Adrian Hunter]

On 03/12/2021 05:57, fred wrote:
> 1.SDR104 card mode PLL frequency is 0x2c28.
> 2.SD2.0/SDR50 card mode PLL frequency is 0X2510.

As before, this commit message is a bit brief.  Can you explain a bit more,
to explain things like:
Why?  Is this a fix?  What difference does an end-user see?

If it is a fix, can you add a Fixes: tag.

Subject line should have a space after each ':'

> 
> Signed-off-by: fred<fred.ai@bayhubtech.com>

Add a space between fred and <fred.ai@bayhubtech.com>

> 
> change in v1:
> When SD2.0/SDR50 card mode,driver need to set PLL frequency 0x2510.
> ---
>  drivers/mmc/host/sdhci-pci-o2micro.c | 8 ++++++++
>  1 file changed, 8 insertions(+)
> 
> diff --git a/drivers/mmc/host/sdhci-pci-o2micro.c b/drivers/mmc/host/sdhci-pci-o2micro.c
> index bac3f0f8185b..32a8ef874efa 100644
> --- a/drivers/mmc/host/sdhci-pci-o2micro.c
> +++ b/drivers/mmc/host/sdhci-pci-o2micro.c
> @@ -568,9 +568,17 @@ static void sdhci_pci_o2_set_clock(struct sdhci_host *host, unsigned int clock)
>  	if ((host->timing == MMC_TIMING_UHS_SDR104) && (clock == 200000000)) {
>  		pci_read_config_dword(chip->pdev, O2_SD_PLL_SETTING, &scratch_32);
>  
> +		/*SDR104 card mode PLL frequency value is 0x2c28*/

For this and other comments, please put a space after '/*' and before '*/'

>  		if ((scratch_32 & 0xFFFF0000) != 0x2c280000)
>  			o2_pci_set_baseclk(chip, 0x2c280000);
>  
> +	} else {

Should this 'else' be in the previous patch instead?

> +		pci_read_config_dword(chip->pdev, O2_SD_PLL_SETTING, &scratch_32);
> +
> +		/*SD2.0,SDR50 card mode PLL DMDN value is 0X2510*/
> +		if ((scratch_32 & 0xFFFF0000) != 0x2510000)
> +			o2_pci_set_baseclk(chip, 0x25100000);
> +
>  		/*If not SDR104 card mode, set 0x354 value 0*/
>  		pci_read_config_dword(chip->pdev, O2_SD_OUTPUT_CLK_SOURCE_SWITCH, &scratch_32);
>  		scratch_32 &= ~(1 << 16);
> 

Re: [PATCH V1 1/2] mmc:sdhci-pci-o2micro: Change implementation of tuning for SDR104 and HS200 mode

[Adrian Hunter]

On 03/12/2021 05:57, fred wrote:
> Select DLL clock of output tuning
> Select fixed output tuning phase 0x9

This commit message is a bit brief.  Can you explain a bit more,
to explain things like:
Why?  Is this a fix?  What difference does an end-user see?

If it is a fix, can you add a Fixes: tag.

> 
> Signed-off-by: fred<fred.ai@bayhubtech.com>

Add a space between fred and <fred.ai@bayhubtech.com>

> 

No blank line here

> ---
> Change in V1:
> 1. Set register 0x354 bit 16 to select DLL clock
> 2. Set register 0x354 bit [23:20] to select fiexd output tuning phase 0x9
> ---
>  drivers/mmc/host/sdhci-pci-o2micro.c | 51 +++++++++++++++++++++++-----
>  1 file changed, 42 insertions(+), 9 deletions(-)
> 
> diff --git a/drivers/mmc/host/sdhci-pci-o2micro.c b/drivers/mmc/host/sdhci-pci-o2micro.c
> index f045c1ee4667..dfd447c1c367 100644
> --- a/drivers/mmc/host/sdhci-pci-o2micro.c
> +++ b/drivers/mmc/host/sdhci-pci-o2micro.c
> @@ -43,6 +43,7 @@
>  #define O2_SD_CAP_REG0		0x334
>  #define O2_SD_UHS1_CAP_SETTING	0x33C
>  #define O2_SD_DELAY_CTRL	0x350
> +#define O2_SD_OUTPUT_CLK_SOURCE_SWITCH	0x354
>  #define O2_SD_UHS2_L1_CTRL	0x35C
>  #define O2_SD_FUNC_REG3		0x3E0
>  #define O2_SD_FUNC_REG4		0x3E4
> @@ -304,6 +305,11 @@ static int sdhci_o2_execute_tuning(struct mmc_host *mmc, u32 opcode)
>  	int current_bus_width = 0;
>  	u32 scratch32 = 0;
>  	u16 scratch = 0;
> +	u8  scratch_8 = 0;
> +	u32 reg_val;
> +	u8  dll_mode;
> +	struct sdhci_pci_slot *slot = sdhci_priv(host);
> +	struct sdhci_pci_chip *chip = slot->chip;

It is nicer kernel style to try to arrange the declarations in
descending line length e.g.

	struct sdhci_host *host = mmc_priv(mmc);
	struct sdhci_pci_slot *slot = sdhci_priv(host);
	struct sdhci_pci_chip *chip = slot->chip;
	int current_bus_width = 0;
	u32 scratch32 = 0;
	u16 scratch = 0;
	u8  scratch_8 = 0;
	u8  dll_mode;
	u32 reg_val;


>  
>  	/*
>  	 * This handler only implements the eMMC tuning that is specific to
> @@ -322,6 +328,28 @@ static int sdhci_o2_execute_tuning(struct mmc_host *mmc, u32 opcode)
>  	scratch |= O2_SD_PWR_FORCE_L0;
>  	sdhci_writew(host, scratch, O2_SD_MISC_CTRL);
>  
> +	/*stop clk*/

For this and other comments, please put a space after '/*' and before '*/'
i.e.
	/* stop clk */

> +	reg_val = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
> +	reg_val &= ~(SDHCI_CLOCK_CARD_EN);
> +	sdhci_writew(host, reg_val, SDHCI_CLOCK_CONTROL);
> +
> +	/*UnLock WP*/
> +	pci_read_config_byte(chip->pdev, O2_SD_LOCK_WP, &scratch_8);
> +	scratch_8 &= 0x7f;
> +	pci_write_config_byte(chip->pdev, O2_SD_LOCK_WP, scratch_8);
> +
> +	//Set pcr 0x354[16] to choose dll clock ,and set the default phase

Please use /* ... */ instead of //

Also 'clock ,and' -> 'clock, and'

> +	dll_mode = 0x9; //set default phase 9

Please use /* ... */ instead of //

> +	pci_read_config_dword(chip->pdev, O2_SD_OUTPUT_CLK_SOURCE_SWITCH, &reg_val);
> +	reg_val &= 0xFF0EFFFF;
> +	reg_val |= ((1 << 16) | (dll_mode << 20));
> +	pci_write_config_dword(chip->pdev, O2_SD_OUTPUT_CLK_SOURCE_SWITCH, reg_val);
> +
> +    /*open clk*/

'open' -> 'start'

> +	reg_val = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
> +	reg_val |= SDHCI_CLOCK_CARD_EN;
> +	sdhci_writew(host, reg_val, SDHCI_CLOCK_CONTROL);
> +
>  	/* wait DLL lock, timeout value 5ms */
>  	if (readx_poll_timeout(sdhci_o2_pll_dll_wdt_control, host,
>  		scratch32, (scratch32 & O2_DLL_LOCK_STATUS), 1, 5000))
> @@ -532,24 +560,29 @@ static void sdhci_pci_o2_set_clock(struct sdhci_host *host, unsigned int clock)
>  
>  	if (clock == 0)
>  		return;
> +	/*UnLock WP*/
> +	pci_read_config_byte(chip->pdev, O2_SD_LOCK_WP, &scratch);
> +	scratch &= 0x7f;
> +	pci_write_config_byte(chip->pdev, O2_SD_LOCK_WP, scratch);
>  
>  	if ((host->timing == MMC_TIMING_UHS_SDR104) && (clock == 200000000)) {
> -		pci_read_config_byte(chip->pdev, O2_SD_LOCK_WP, &scratch);
> -
> -		scratch &= 0x7f;
> -		pci_write_config_byte(chip->pdev, O2_SD_LOCK_WP, scratch);
> -
>  		pci_read_config_dword(chip->pdev, O2_SD_PLL_SETTING, &scratch_32);
>  
>  		if ((scratch_32 & 0xFFFF0000) != 0x2c280000)
>  			o2_pci_set_baseclk(chip, 0x2c280000);
>  
> -		pci_read_config_byte(chip->pdev, O2_SD_LOCK_WP, &scratch);
> -
> -		scratch |= 0x80;
> -		pci_write_config_byte(chip->pdev, O2_SD_LOCK_WP, scratch);
> +		/*If not SDR104 card mode, set 0x354 value 0*/

This comment contradicts the 'if' statement before it, because
host->timing == MMC_TIMING_UHS_SDR104 implies that it is SDR104 card mode.


> +		pci_read_config_dword(chip->pdev, O2_SD_OUTPUT_CLK_SOURCE_SWITCH, &scratch_32);
> +		scratch_32 &= ~(1 << 16);
> +		scratch_32 &= ~(0xf << 20);
> +		pci_write_config_dword(chip->pdev, O2_SD_OUTPUT_CLK_SOURCE_SWITCH,scratch_32);

Please add a space before 'scratch_32'

>  	}
>  
> +    /*Lock WP*/
> +	pci_read_config_byte(chip->pdev, O2_SD_LOCK_WP, &scratch);
> +	scratch |= 0x80;
> +	pci_write_config_byte(chip->pdev, O2_SD_LOCK_WP, scratch);
> +
>  	clk = sdhci_calc_clk(host, clock, &host->mmc->actual_clock);
>  	sdhci_o2_enable_clk(host, clk);
>  }
>