Re: [PATCH 1/6] dt-bindings: phy: ti: phy-gmii-sel: Add bindings for J721e

[Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>]

On 14/09/2022 11:39, Siddharth Vadapalli wrote:
> TI's J721e SoC supports additional PHY modes like QSGMII and SGMII
> that are not supported on earlier SoCs. Add a compatible for it.
> 
> Extend ti,qsgmii-main-ports property to support selection of upto
> two main ports at once across the two QSGMII interfaces.
> 
> Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
> ---
>  .../bindings/phy/ti,phy-gmii-sel.yaml         | 52 ++++++++++++++++---
>  1 file changed, 46 insertions(+), 6 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/phy/ti,phy-gmii-sel.yaml b/Documentation/devicetree/bindings/phy/ti,phy-gmii-sel.yaml
> index da7cac537e15..1e19efab018b 100644
> --- a/Documentation/devicetree/bindings/phy/ti,phy-gmii-sel.yaml
> +++ b/Documentation/devicetree/bindings/phy/ti,phy-gmii-sel.yaml
> @@ -54,6 +54,7 @@ properties:
>        - ti,dm814-phy-gmii-sel
>        - ti,am654-phy-gmii-sel
>        - ti,j7200-cpsw5g-phy-gmii-sel
> +      - ti,j721e-cpsw9g-phy-gmii-sel
>  
>    reg:
>      maxItems: 1
> @@ -65,12 +66,19 @@ properties:
>      description: |
>        Required only for QSGMII mode. Array to select the port for
>        QSGMII main mode. Rest of the ports are selected as QSGMII_SUB
> -      ports automatically. Any one of the 4 CPSW5G ports can act as the
> -      main port with the rest of them being the QSGMII_SUB ports.
> -    maxItems: 1
> -    items:
> -      minimum: 1
> -      maximum: 4

minItems: 1
maxItems: 2
  items:
    minimum: 1
    maximum: 8

> +      ports automatically. For J7200 CPSW5G with the compatible:
> +      ti,j7200-cpsw5g-phy-gmii-sel, ti,qsgmii-main-ports is an
> +      array of only one element, which is the port number ranging from
> +      1 to 4. For J721e CPSW9G with the compatible:
> +      ti,j721e-cpsw9g-phy-gmii-sel, ti,qsgmii-main-ports is an array
> +      of two elements, which corresponds to two potential QSGMII main
> +      ports. The first element and second element of the array can both
> +      range from 1 to 8 each, corresponding to two QSGMII main ports.
> +      For J721e CPSW9G, to configure port 2 as the first QSGMII main
> +      port and port 7 as the second QSGMII main port, we specify:
> +      ti,qsgmii-main-ports = <2>, <7>;
> +      If only one QSGMII main port is desired, mention the same main
> +      port twice.
>  
>  allOf:
>    - if:
> @@ -81,12 +89,43 @@ allOf:
>                - ti,dra7xx-phy-gmii-sel
>                - ti,dm814-phy-gmii-sel
>                - ti,am654-phy-gmii-sel
> +              - ti,j7200-cpsw5g-phy-gmii-sel
> +              - ti,j721e-cpsw9g-phy-gmii-sel
>      then:
>        properties:
>          '#phy-cells':
>            const: 1
>            description: CPSW port number (starting from 1)
>  
> +  - if:
> +      properties:
> +        compatible:
> +          contains:
> +            enum:
> +              - ti,j7200-cpsw5g-phy-gmii-sel
> +    then:
> +      properties:
> +        ti,qsgmii-main-ports:
> +          maxItems: 1
> +          items:
> +            minimum: 1
> +            maximum: 4
> +
> +  - if:
> +      properties:
> +        compatible:
> +          contains:
> +            enum:
> +              - ti,j721e-cpsw9g-phy-gmii-sel
> +    then:
> +      properties:
> +        ti,qsgmii-main-ports:
> +          minItems: 2
> +          maxItems: 2
> +          items:
> +            minimum: 1
> +            maximum: 8
> +
>    - if:
>        not:
>          properties:
> @@ -94,6 +133,7 @@ allOf:
>              contains:
>                enum:
>                  - ti,j7200-cpsw5g-phy-gmii-sel
> +                - ti,j721e-cpsw9g-phy-gmii-sel
>      then:
>        properties:
>          ti,qsgmii-main-ports: false

This is interesting here... Did you test the bindings with your DTS?


Best regards,
Krzysztof

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy