Linux-PHY Archive on lore.kernel.org

* [PATCH V2 1/2] arm64: dts: qcom: Add SD Card support for Shikra SoC
From: Monish Chunara @ 2026-06-30 16:56 UTC (permalink / raw)
  To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
	Conor Dooley, Vinod Koul, Neil Armstrong, Wesley Cheng,
	Ulf Hansson, Kernel Team
  Cc: linux-arm-msm, devicetree, linux-kernel, linux-phy, linux-mmc,
	Nitin Rawat, Pradeep Pragallapati, Komal Bajaj, Monish Chunara,
	Konrad Dybcio
In-Reply-To: <20260630165700.1886608-1-monish.chunara@oss.qualcomm.com>

Add support for SD card on Shikra SoC and enable the required pinctrl
configurations.

Signed-off-by: Monish Chunara <monish.chunara@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/shikra.dtsi | 97 ++++++++++++++++++++++++++++
 1 file changed, 97 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/shikra.dtsi b/arch/arm64/boot/dts/qcom/shikra.dtsi
index e67fe047a683..cfdee8a2526e 100644
--- a/arch/arm64/boot/dts/qcom/shikra.dtsi
+++ b/arch/arm64/boot/dts/qcom/shikra.dtsi
@@ -829,6 +829,53 @@ rclk-pins {
 					bias-bus-hold;
 				};
 			};
+
+			sdc2_default: sdc2-default-state {
+				clk-pins {
+					pins = "sdc2_clk";
+					drive-strength = <14>;
+					bias-disable;
+				};
+
+				cmd-pins {
+					pins = "sdc2_cmd";
+					drive-strength = <14>;
+					bias-pull-up;
+				};
+
+				data-pins {
+					pins = "sdc2_data";
+					drive-strength = <14>;
+					bias-pull-up;
+				};
+			};
+
+			sdc2_sleep: sdc2-sleep-state {
+				clk-pins {
+					pins = "sdc2_clk";
+					drive-strength = <2>;
+					bias-disable;
+				};
+
+				cmd-pins {
+					pins = "sdc2_cmd";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+
+				data-pins {
+					pins = "sdc2_data";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			sdc2_card_det_n: sd-card-det-n-state {
+				pins = "gpio89";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
 		};
 
 		pmu@c91000 {
@@ -1081,6 +1128,56 @@ opp-384000000 {
 			};
 		};
 
+		sdhc_2: mmc@4784000 {
+			compatible = "qcom,shikra-sdhci", "qcom,sdhci-msm-v5";
+			reg = <0x0 0x4784000 0x0 0x1000>;
+
+			interrupts = <GIC_SPI 350 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq",
+					  "pwr_irq";
+
+			bus-width = <4>;
+
+			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
+				 <&gcc GCC_SDCC2_APPS_CLK>,
+				 <&rpmcc RPM_SMD_XO_CLK_SRC>;
+			clock-names = "iface",
+				      "core",
+				      "xo";
+
+			qcom,dll-config = <0x0007442c>;
+			qcom,ddr-config = <0x80040868>;
+
+			iommus = <&apps_smmu 0x0a0 0x0>;
+
+			interconnects = <&system_noc MASTER_SDCC_2 RPM_ALWAYS_TAG
+					 &mc_virt SLAVE_EBI_CH0 RPM_ALWAYS_TAG>,
+					<&mem_noc MASTER_AMPSS_M0 RPM_ACTIVE_TAG
+					 &config_noc SLAVE_SDCC_2 RPM_ACTIVE_TAG>;
+			interconnect-names = "sdhc-ddr",
+					     "cpu-sdhc";
+
+			power-domains = <&rpmpd RPMPD_VDDCX>;
+			operating-points-v2 = <&sdhc2_opp_table>;
+
+			status = "disabled";
+
+			sdhc2_opp_table: opp-table-2 {
+				compatible = "operating-points-v2";
+
+				opp-100000000 {
+					opp-hz = /bits/ 64 <100000000>;
+					required-opps = <&rpmpd_opp_low_svs>;
+				};
+
+				opp-202000000 {
+					opp-hz = /bits/ 64 <202000000>;
+					required-opps = <&rpmpd_opp_svs_plus>;
+				};
+			};
+		};
+
 		gpi_dma0: dma-controller@4a00000 {
 			compatible = "qcom,shikra-gpi-dma", "qcom,sm6350-gpi-dma";
 			reg = <0x0 0x04a00000 0x0 0x60000>;
-- 
2.34.1


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

^ permalink raw reply related