* Debian: how do I determine if RAID is working?
@ 2004-04-30 5:47 Steve Dondley
2004-04-30 8:25 ` Marc
2004-04-30 11:37 ` Joshua Baker-LePain
0 siblings, 2 replies; 3+ messages in thread
From: Steve Dondley @ 2004-04-30 5:47 UTC (permalink / raw)
To: linux-raid
According to dmesg, the driver that I configured into my kernel for my 3ware
7000 series controller card gets installed at boot time with no errors.
That's nice, but aside from disconnecting one of the hard drives, how can I
verify my RAID configuration is working?
I'm running Debian (woody) kernel 2.4.18, raid 1 configuration on two
ATA/IDE hard drives.
Thanks!
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: Debian: how do I determine if RAID is working?
2004-04-30 5:47 Debian: how do I determine if RAID is working? Steve Dondley
@ 2004-04-30 8:25 ` Marc
2004-04-30 11:37 ` Joshua Baker-LePain
1 sibling, 0 replies; 3+ messages in thread
From: Marc @ 2004-04-30 8:25 UTC (permalink / raw)
To: linux-raid
mdadm has a few options for examining the configuration/status of arrays.
You can also 'cat /proc/mdstat' for a quick look at your raid array's
status..
--
---------- Original Message -----------
From: "Steve Dondley" <s@dondley.com>
To: <linux-raid@vger.kernel.org>
Sent: Fri, 30 Apr 2004 01:47:58 -0400
Subject: Debian: how do I determine if RAID is working?
> According to dmesg, the driver that I configured into my kernel for
> my 3ware 7000 series controller card gets installed at boot time
> with no errors. That's nice, but aside from disconnecting one of the
> hard drives, how can I verify my RAID configuration is working?
>
> I'm running Debian (woody) kernel 2.4.18, raid 1 configuration on two
> ATA/IDE hard drives.
>
> Thanks!
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-
> raid" in the body of a message to majordomo@vger.kernel.org More
> majordomo info at http://vger.kernel.org/majordomo-info.html
------- End of Original Message -------
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: Debian: how do I determine if RAID is working?
2004-04-30 5:47 Debian: how do I determine if RAID is working? Steve Dondley
2004-04-30 8:25 ` Marc
@ 2004-04-30 11:37 ` Joshua Baker-LePain
1 sibling, 0 replies; 3+ messages in thread
From: Joshua Baker-LePain @ 2004-04-30 11:37 UTC (permalink / raw)
To: Steve Dondley; +Cc: linux-raid
On Fri, 30 Apr 2004 at 1:47am, Steve Dondley wrote
> According to dmesg, the driver that I configured into my kernel for my 3ware
> 7000 series controller card gets installed at boot time with no errors.
> That's nice, but aside from disconnecting one of the hard drives, how can I
> verify my RAID configuration is working?
>
> I'm running Debian (woody) kernel 2.4.18, raid 1 configuration on two
> ATA/IDE hard drives.
Are you using software or hardware RAID? If software, the commands were
already posted. If hardware, you can install either 3dm or the CLI
utilities from 3ware to monitor the array.
--
Joshua Baker-LePain
Department of Biomedical Engineering
Duke University
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2004-04-30 11:37 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2004-04-30 5:47 Debian: how do I determine if RAID is working? Steve Dondley
2004-04-30 8:25 ` Marc
2004-04-30 11:37 ` Joshua Baker-LePain
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox