* [PATCH v2 01/22] dt-bindings: pincfg-node: Add property 'input-debounce-nanoseconds'
2026-05-14 11:11 [PATCH v2 00/22] Add basic pinctrl drivers for JHB100 SoC Changhuang Liang
@ 2026-05-14 11:11 ` Changhuang Liang
2026-05-14 18:35 ` Conor Dooley
2026-05-14 11:11 ` [PATCH v2 02/22] pinctrl: pinconf-generic: " Changhuang Liang
` (20 subsequent siblings)
21 siblings, 1 reply; 32+ messages in thread
From: Changhuang Liang @ 2026-05-14 11:11 UTC (permalink / raw)
To: Linus Walleij, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Emil Renner Berthing, Paul Walmsley, Albert Ou, Palmer Dabbelt,
Alexandre Ghiti, Philipp Zabel, Bartosz Golaszewski
Cc: linux-gpio, linux-kernel, devicetree, linux-riscv,
Lianfeng Ouyang, Changhuang Liang
Add the property 'input-debounce-nanoseconds' to specify debounce time
in nanoseconds as an alternative to the existing 'input-debounce' which
uses microseconds. Make the new property unavailable when the existing
property 'input-debounce' is selected to prevent conflicting definitions.
Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
---
.../devicetree/bindings/pinctrl/pincfg-node.yaml | 12 ++++++++++++
1 file changed, 12 insertions(+)
diff --git a/Documentation/devicetree/bindings/pinctrl/pincfg-node.yaml b/Documentation/devicetree/bindings/pinctrl/pincfg-node.yaml
index 97dbce8a261f..4db66cdf438c 100644
--- a/Documentation/devicetree/bindings/pinctrl/pincfg-node.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/pincfg-node.yaml
@@ -104,6 +104,11 @@ properties:
description: Takes the debounce time in usec as argument or 0 to disable
debouncing
+ input-debounce-nanoseconds:
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ description: Takes the debounce time in nsec as argument or 0 to disable
+ debouncing
+
power-source:
$ref: /schemas/types.yaml#/definitions/uint32
description: select between different power supplies
@@ -214,6 +219,13 @@ allOf:
input-schmitt-enable: false
input-schmitt-microvolt: false
+ - if:
+ required:
+ - input-debounce
+ then:
+ properties:
+ input-debounce-nanoseconds: false
+
- if:
required:
- drive-strength
--
2.25.1
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply related [flat|nested] 32+ messages in thread* Re: [PATCH v2 01/22] dt-bindings: pincfg-node: Add property 'input-debounce-nanoseconds'
2026-05-14 11:11 ` [PATCH v2 01/22] dt-bindings: pincfg-node: Add property 'input-debounce-nanoseconds' Changhuang Liang
@ 2026-05-14 18:35 ` Conor Dooley
0 siblings, 0 replies; 32+ messages in thread
From: Conor Dooley @ 2026-05-14 18:35 UTC (permalink / raw)
To: Changhuang Liang
Cc: Linus Walleij, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Emil Renner Berthing, Paul Walmsley, Albert Ou, Palmer Dabbelt,
Alexandre Ghiti, Philipp Zabel, Bartosz Golaszewski, linux-gpio,
linux-kernel, devicetree, linux-riscv, Lianfeng Ouyang
[-- Attachment #1.1: Type: text/plain, Size: 1824 bytes --]
On Thu, May 14, 2026 at 04:11:57AM -0700, Changhuang Liang wrote:
> Add the property 'input-debounce-nanoseconds' to specify debounce time
> in nanoseconds as an alternative to the existing 'input-debounce' which
> uses microseconds. Make the new property unavailable when the existing
> property 'input-debounce' is selected to prevent conflicting definitions.
>
> Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
> ---
> .../devicetree/bindings/pinctrl/pincfg-node.yaml | 12 ++++++++++++
> 1 file changed, 12 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/pincfg-node.yaml b/Documentation/devicetree/bindings/pinctrl/pincfg-node.yaml
> index 97dbce8a261f..4db66cdf438c 100644
> --- a/Documentation/devicetree/bindings/pinctrl/pincfg-node.yaml
> +++ b/Documentation/devicetree/bindings/pinctrl/pincfg-node.yaml
> @@ -104,6 +104,11 @@ properties:
> description: Takes the debounce time in usec as argument or 0 to disable
> debouncing
>
> + input-debounce-nanoseconds:
-ns is the standard suffix here, and if you use it you can drop the ref
below.
pw-bot: changes-requested
> + $ref: /schemas/types.yaml#/definitions/uint32-array
> + description: Takes the debounce time in nsec as argument or 0 to disable
> + debouncing
> +
> power-source:
> $ref: /schemas/types.yaml#/definitions/uint32
> description: select between different power supplies
> @@ -214,6 +219,13 @@ allOf:
> input-schmitt-enable: false
> input-schmitt-microvolt: false
>
> + - if:
> + required:
> + - input-debounce
> + then:
> + properties:
> + input-debounce-nanoseconds: false
> +
> - if:
> required:
> - drive-strength
> --
> 2.25.1
>
>
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
[-- Attachment #2: Type: text/plain, Size: 161 bytes --]
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply [flat|nested] 32+ messages in thread
* [PATCH v2 02/22] pinctrl: pinconf-generic: Add property 'input-debounce-nanoseconds'
2026-05-14 11:11 [PATCH v2 00/22] Add basic pinctrl drivers for JHB100 SoC Changhuang Liang
2026-05-14 11:11 ` [PATCH v2 01/22] dt-bindings: pincfg-node: Add property 'input-debounce-nanoseconds' Changhuang Liang
@ 2026-05-14 11:11 ` Changhuang Liang
2026-05-14 11:11 ` [PATCH v2 03/22] pinctrl: pinctrl-generic: Make the "function" property optional Changhuang Liang
` (19 subsequent siblings)
21 siblings, 0 replies; 32+ messages in thread
From: Changhuang Liang @ 2026-05-14 11:11 UTC (permalink / raw)
To: Linus Walleij, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Emil Renner Berthing, Paul Walmsley, Albert Ou, Palmer Dabbelt,
Alexandre Ghiti, Philipp Zabel, Bartosz Golaszewski
Cc: linux-gpio, linux-kernel, devicetree, linux-riscv,
Lianfeng Ouyang, Changhuang Liang
Add 'input-debounce-nanoseconds' to the generic parameters used for
parsing DT files, along with the corresponding configuration parameter
PIN_CONFIG_INPUT_DEBOUNCE_NS. This allows debounce time to be specified
in nanoseconds as an alternative to the existing 'input-debounce'
property which uses microseconds
Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
---
drivers/pinctrl/pinconf-generic.c | 2 ++
include/linux/pinctrl/pinconf-generic.h | 5 +++++
2 files changed, 7 insertions(+)
diff --git a/drivers/pinctrl/pinconf-generic.c b/drivers/pinctrl/pinconf-generic.c
index 64ed28309788..02f88b2b8120 100644
--- a/drivers/pinctrl/pinconf-generic.c
+++ b/drivers/pinctrl/pinconf-generic.c
@@ -43,6 +43,7 @@ static const struct pin_config_item conf_items[] = {
PCONFDUMP(PIN_CONFIG_DRIVE_STRENGTH, "output drive strength", "mA", true),
PCONFDUMP(PIN_CONFIG_DRIVE_STRENGTH_UA, "output drive strength", "uA", true),
PCONFDUMP(PIN_CONFIG_INPUT_DEBOUNCE, "input debounce", "usec", true),
+ PCONFDUMP(PIN_CONFIG_INPUT_DEBOUNCE_NS, "input debounce", "nsec", true),
PCONFDUMP(PIN_CONFIG_INPUT_ENABLE, "input enabled", NULL, false),
PCONFDUMP(PIN_CONFIG_INPUT_SCHMITT, "input schmitt trigger", NULL, false),
PCONFDUMP(PIN_CONFIG_INPUT_SCHMITT_UV, "input schmitt threshold", "uV", true),
@@ -185,6 +186,7 @@ static const struct pinconf_generic_params dt_params[] = {
{ "drive-strength", PIN_CONFIG_DRIVE_STRENGTH, 0 },
{ "drive-strength-microamp", PIN_CONFIG_DRIVE_STRENGTH_UA, 0 },
{ "input-debounce", PIN_CONFIG_INPUT_DEBOUNCE, 0 },
+ { "input-debounce-nanoseconds", PIN_CONFIG_INPUT_DEBOUNCE_NS, 0 },
{ "input-disable", PIN_CONFIG_INPUT_ENABLE, 0 },
{ "input-enable", PIN_CONFIG_INPUT_ENABLE, 1 },
{ "input-schmitt", PIN_CONFIG_INPUT_SCHMITT, 0 },
diff --git a/include/linux/pinctrl/pinconf-generic.h b/include/linux/pinctrl/pinconf-generic.h
index a5d4b2d8633a..1df63c732b99 100644
--- a/include/linux/pinctrl/pinconf-generic.h
+++ b/include/linux/pinctrl/pinconf-generic.h
@@ -71,6 +71,10 @@ struct pinctrl_map;
* which means it will wait for signals to settle when reading inputs. The
* argument gives the debounce time in usecs. Setting the
* argument to zero turns debouncing off.
+ * @PIN_CONFIG_INPUT_DEBOUNCE_NS: this will configure the pin to debounce mode,
+ * which means it will wait for signals to settle when reading inputs. The
+ * argument gives the debounce time in nsecs. Setting the
+ * argument to zero turns debouncing off.
* @PIN_CONFIG_INPUT_ENABLE: enable the pin's input. Note that this does not
* affect the pin's ability to drive output. 1 enables input, 0 disables
* input.
@@ -143,6 +147,7 @@ enum pin_config_param {
PIN_CONFIG_DRIVE_STRENGTH,
PIN_CONFIG_DRIVE_STRENGTH_UA,
PIN_CONFIG_INPUT_DEBOUNCE,
+ PIN_CONFIG_INPUT_DEBOUNCE_NS,
PIN_CONFIG_INPUT_ENABLE,
PIN_CONFIG_INPUT_SCHMITT,
PIN_CONFIG_INPUT_SCHMITT_ENABLE,
--
2.25.1
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply related [flat|nested] 32+ messages in thread* [PATCH v2 03/22] pinctrl: pinctrl-generic: Make the "function" property optional
2026-05-14 11:11 [PATCH v2 00/22] Add basic pinctrl drivers for JHB100 SoC Changhuang Liang
2026-05-14 11:11 ` [PATCH v2 01/22] dt-bindings: pincfg-node: Add property 'input-debounce-nanoseconds' Changhuang Liang
2026-05-14 11:11 ` [PATCH v2 02/22] pinctrl: pinconf-generic: " Changhuang Liang
@ 2026-05-14 11:11 ` Changhuang Liang
2026-05-14 18:46 ` Conor Dooley
2026-05-14 11:12 ` [PATCH v2 04/22] dt-bindings: pinctrl: Add starfive,jhb100-sys0-pinctrl Changhuang Liang
` (18 subsequent siblings)
21 siblings, 1 reply; 32+ messages in thread
From: Changhuang Liang @ 2026-05-14 11:11 UTC (permalink / raw)
To: Linus Walleij, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Emil Renner Berthing, Paul Walmsley, Albert Ou, Palmer Dabbelt,
Alexandre Ghiti, Philipp Zabel, Bartosz Golaszewski
Cc: linux-gpio, linux-kernel, devicetree, linux-riscv,
Lianfeng Ouyang, Changhuang Liang
Some pinctrl subnodes only need to configure pin properties (e.g.,
power-source, bias, drive strength) without assigning any mux function.
Currently, the driver requires a valid "function" property for all
pinctrl subnodes. This forces the addition of dummy or redundant
"function" entries when only pin configuration is needed.
Example use case:
gpios-configs {
config {
pins = <0 1 2 3>;
power-source = <0>;
};
};
Make the "function" property optional. If it is missing, skip adding
the mux map and only process the pin configuration.
Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
---
drivers/pinctrl/pinctrl-generic.c | 37 ++++++++++++++++++++++---------
1 file changed, 27 insertions(+), 10 deletions(-)
diff --git a/drivers/pinctrl/pinctrl-generic.c b/drivers/pinctrl/pinctrl-generic.c
index efb39c6a6703..c7dd0924aa0e 100644
--- a/drivers/pinctrl/pinctrl-generic.c
+++ b/drivers/pinctrl/pinctrl-generic.c
@@ -62,19 +62,36 @@ static int pinctrl_generic_pins_function_dt_subnode_to_map(struct pinctrl_dev *p
pins[i] = pin;
- ret = of_property_read_string(np, "function", &functions[i]);
- if (ret)
- return ret;
+ if (functions) {
+ ret = of_property_read_string(np, "function", &functions[i]);
+ if (ret < 0) {
+ /* EINVAL = missing, which is fine since it's optional */
+ if (ret != -EINVAL) {
+ dev_err(dev, "%pOF: could not parse property function\n",
+ np);
+ return ret;
+ }
+
+ devm_kfree(dev, functions);
+ functions = NULL;
+
+ /* Continue parsing all pins */
+ continue;
+ }
+ }
}
- ret = pinctrl_utils_reserve_map(pctldev, maps, num_reserved_maps, num_maps, reserve);
- if (ret)
- return ret;
+ if (functions) {
+ ret = pinctrl_utils_reserve_map(pctldev, maps, num_reserved_maps,
+ num_maps, reserve);
+ if (ret)
+ return ret;
- ret = pinctrl_utils_add_map_mux(pctldev, maps, num_reserved_maps, num_maps, group_name,
- parent->name);
- if (ret < 0)
- return ret;
+ ret = pinctrl_utils_add_map_mux(pctldev, maps, num_reserved_maps,
+ num_maps, group_name, parent->name);
+ if (ret < 0)
+ return ret;
+ }
ret = pinctrl_generic_add_group(pctldev, group_name, pins, npins, functions);
if (ret < 0)
--
2.25.1
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply related [flat|nested] 32+ messages in thread* Re: [PATCH v2 03/22] pinctrl: pinctrl-generic: Make the "function" property optional
2026-05-14 11:11 ` [PATCH v2 03/22] pinctrl: pinctrl-generic: Make the "function" property optional Changhuang Liang
@ 2026-05-14 18:46 ` Conor Dooley
0 siblings, 0 replies; 32+ messages in thread
From: Conor Dooley @ 2026-05-14 18:46 UTC (permalink / raw)
To: Changhuang Liang
Cc: Linus Walleij, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Emil Renner Berthing, Paul Walmsley, Albert Ou, Palmer Dabbelt,
Alexandre Ghiti, Philipp Zabel, Bartosz Golaszewski, linux-gpio,
linux-kernel, devicetree, linux-riscv, Lianfeng Ouyang
[-- Attachment #1.1: Type: text/plain, Size: 3019 bytes --]
On Thu, May 14, 2026 at 04:11:59AM -0700, Changhuang Liang wrote:
> Some pinctrl subnodes only need to configure pin properties (e.g.,
> power-source, bias, drive strength) without assigning any mux function.
>
> Currently, the driver requires a valid "function" property for all
> pinctrl subnodes. This forces the addition of dummy or redundant
> "function" entries when only pin configuration is needed.
>
> Example use case:
> gpios-configs {
> config {
> pins = <0 1 2 3>;
> power-source = <0>;
> };
> };
>
> Make the "function" property optional. If it is missing, skip adding
> the mux map and only process the pin configuration.
I looked through the series though and all controllers appear
to have pins and functions, is it the case that gpio is the default for
these pins, so you are omitting the functions property when you are
using the pin in gpio mode? Saying that the functions property is
"redudant" makes it seem like this might be the case?
I've got some feedback here, but I can't really provide it without
knowing the answer to that question.
Cheers,
Conor.
>
> Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
> ---
> drivers/pinctrl/pinctrl-generic.c | 37 ++++++++++++++++++++++---------
> 1 file changed, 27 insertions(+), 10 deletions(-)
>
> diff --git a/drivers/pinctrl/pinctrl-generic.c b/drivers/pinctrl/pinctrl-generic.c
> index efb39c6a6703..c7dd0924aa0e 100644
> --- a/drivers/pinctrl/pinctrl-generic.c
> +++ b/drivers/pinctrl/pinctrl-generic.c
> @@ -62,19 +62,36 @@ static int pinctrl_generic_pins_function_dt_subnode_to_map(struct pinctrl_dev *p
>
> pins[i] = pin;
>
> - ret = of_property_read_string(np, "function", &functions[i]);
> - if (ret)
> - return ret;
> + if (functions) {
> + ret = of_property_read_string(np, "function", &functions[i]);
> + if (ret < 0) {
> + /* EINVAL = missing, which is fine since it's optional */
> + if (ret != -EINVAL) {
> + dev_err(dev, "%pOF: could not parse property function\n",
> + np);
> + return ret;
> + }
> +
> + devm_kfree(dev, functions);
> + functions = NULL;
> +
> + /* Continue parsing all pins */
> + continue;
> + }
> + }
> }
>
> - ret = pinctrl_utils_reserve_map(pctldev, maps, num_reserved_maps, num_maps, reserve);
> - if (ret)
> - return ret;
> + if (functions) {
> + ret = pinctrl_utils_reserve_map(pctldev, maps, num_reserved_maps,
> + num_maps, reserve);
> + if (ret)
> + return ret;
>
> - ret = pinctrl_utils_add_map_mux(pctldev, maps, num_reserved_maps, num_maps, group_name,
> - parent->name);
> - if (ret < 0)
> - return ret;
> + ret = pinctrl_utils_add_map_mux(pctldev, maps, num_reserved_maps,
> + num_maps, group_name, parent->name);
> + if (ret < 0)
> + return ret;
> + }
>
> ret = pinctrl_generic_add_group(pctldev, group_name, pins, npins, functions);
> if (ret < 0)
> --
> 2.25.1
>
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
[-- Attachment #2: Type: text/plain, Size: 161 bytes --]
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply [flat|nested] 32+ messages in thread
* [PATCH v2 04/22] dt-bindings: pinctrl: Add starfive,jhb100-sys0-pinctrl
2026-05-14 11:11 [PATCH v2 00/22] Add basic pinctrl drivers for JHB100 SoC Changhuang Liang
` (2 preceding siblings ...)
2026-05-14 11:11 ` [PATCH v2 03/22] pinctrl: pinctrl-generic: Make the "function" property optional Changhuang Liang
@ 2026-05-14 11:12 ` Changhuang Liang
2026-05-14 18:52 ` Conor Dooley
2026-05-14 11:12 ` [PATCH v2 05/22] pinctrl: starfive: Add StarFive JHB100 sys0 controller driver Changhuang Liang
` (17 subsequent siblings)
21 siblings, 1 reply; 32+ messages in thread
From: Changhuang Liang @ 2026-05-14 11:12 UTC (permalink / raw)
To: Linus Walleij, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Emil Renner Berthing, Paul Walmsley, Albert Ou, Palmer Dabbelt,
Alexandre Ghiti, Philipp Zabel, Bartosz Golaszewski
Cc: linux-gpio, linux-kernel, devicetree, linux-riscv,
Lianfeng Ouyang, Changhuang Liang
Add pinctrl bindings for StarFive JHB100 SoC System-0(sys0) pinctrl
controller.
Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
---
.../pinctrl/starfive,jhb100-sys0-pinctrl.yaml | 175 ++++++++++++++++++
.../pinctrl/starfive,jhb100-pinctrl.h | 17 ++
2 files changed, 192 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys0-pinctrl.yaml
create mode 100644 include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h
diff --git a/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys0-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys0-pinctrl.yaml
new file mode 100644
index 000000000000..21d3693587fd
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys0-pinctrl.yaml
@@ -0,0 +1,175 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/starfive,jhb100-sys0-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: StarFive JHB100 System-0 Pin Controller
+
+description: |
+ Pinctrl bindings for JHB100 RISC-V SoC from StarFive Technology Ltd.
+
+ The JHB100 SoC has 13 pinctrl domains - sys0, sys0h, sys1, sys2, per0, per1,
+ per2, per2pok, per3, adc0, adc1, emmc, and vga.
+ This document provides an overview of the "sys0" pinctrl domain.
+
+ The "sys0" domain has a pin controller which provides
+ - function selection for GPIO pads.
+ - GPIO pad configuration.
+ - GPIO interrupt handling.
+
+ In the SYS0 Pin Controller, there are 4 multi-function GPIO_PADs. Each of
+ them can be multiplexed to different hardware blocks through function
+ selection and each iopad has a maximum of up to 2 functions - 0 and 1.
+ Function 0 is the default function which is generally the GPIO function
+ (or occasionally, it can be a peripheral signal).
+ Function 1 is the alternate function or peripheral signal that can be
+ routed to the iopad. The function selection is carried out by writing
+ the function number to the iopad function select register.
+
+ Each iopad is configurable with parameters such as input-enable, internal
+ pull-up/pull-down bias, drive strength, schmitt trigger, slew rate, input
+ debounce nanoseconds, power source and drive type (open-drain or push-pull).
+
+maintainers:
+ - Alex Soo <yuklin.soo@starfivetech.com>
+
+properties:
+ compatible:
+ items:
+ - const: starfive,jhb100-sys0-pinctrl
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ resets:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ interrupt-controller: true
+
+ '#interrupt-cells':
+ const: 3
+
+ gpio-controller: true
+
+ '#gpio-cells':
+ const: 3
+
+ gpio-ranges: true
+
+ gpio-line-names: true
+
+patternProperties:
+ '-grp$':
+ type: object
+ additionalProperties: false
+ patternProperties:
+ '-pins$':
+ type: object
+ description: |
+ A pinctrl node should contain at least one subnode representing the
+ pinctrl groups available in the domain. Each subnode will list the
+ pins it needs, and how they should be configured, with regard to
+ function selection, bias, input enable/disable, input schmitt
+ trigger enable/disable, slew-rate, input debounce nanoseconds,
+ drive-open-drain, drive-push-pull, power-source and drive-strength.
+ allOf:
+ - $ref: /schemas/pinctrl/pincfg-node.yaml
+ - $ref: /schemas/pinctrl/pinmux-node.yaml
+ unevaluatedProperties: false
+
+ properties:
+ pins:
+ description:
+ The list of IOs that properties in the pincfg node apply to.
+
+ function:
+ description:
+ A string containing the name of the function to mux for these
+ pins.
+ enum: [ auxpwrgood, gpio, hbled, pe2rst_out ]
+
+ bias-disable: true
+
+ bias-pull-down:
+ type: boolean
+
+ bias-pull-up:
+ oneOf:
+ - type: boolean
+ - enum: [ 600, 900, 1200, 2000 ]
+ description: Pull up RSEL type resistance values (in ohms)
+ description:
+ For normal pull up type there is no need to specify a resistance
+ value, hence this can be specified as a boolean property.
+ For RSEL pull up type a resistance value (in ohms) can be added.
+
+ drive-open-drain: true
+
+ drive-push-pull: true
+
+ drive-strength:
+ enum: [ 2, 4, 8, 12 ]
+
+ drive-strength-microamp:
+ enum: [ 2000, 4000, 8000, 12000 ]
+
+ input-debounce-nanoseconds:
+ minimum: 0
+ maximum: 4294967295
+
+ input-disable: true
+
+ input-enable: true
+
+ input-schmitt-enable: true
+
+ input-schmitt-disable: true
+
+ power-source:
+ enum: [ 0, 1, 2 ]
+
+ slew-rate:
+ enum: [ 0, 1 ]
+ default: 0
+ description: |
+ 0: slow (half frequency)
+ 1: fast
+
+required:
+ - compatible
+ - reg
+ - resets
+ - interrupts
+ - interrupt-controller
+ - '#interrupt-cells'
+ - gpio-controller
+ - '#gpio-cells'
+ - gpio-ranges
+
+additionalProperties: false
+
+examples:
+ - |
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ pinctrl_sys0: pinctrl@13080000 {
+ compatible = "starfive,jhb100-sys0-pinctrl";
+ reg = <0x0 0x13080000 0x0 0x800>;
+ resets = <&sys0crg 2>;
+ interrupts = <56>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ gpio-ranges = <&pinctrl_sys0 0 0 0 4>;
+ };
+ };
diff --git a/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h b/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h
new file mode 100644
index 000000000000..6d8f5516a178
--- /dev/null
+++ b/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h
@@ -0,0 +1,17 @@
+/* SPDX-License-Identifier: GPL-2.0 OR MIT */
+/*
+ * Copyright (C) 2022 StarFive Technology Co., Ltd.
+ *
+ * Author: Changhuang Liang <changhuang.liang@starfivetech.com>
+ */
+
+#ifndef __DT_BINDINGS_PINCTRL_STARFIVE_JHB100_H__
+#define __DT_BINDINGS_PINCTRL_STARFIVE_JHB100_H__
+
+/* sys0 pad numbers */
+#define PADNUM_SYS0_GPIO_A0 0
+#define PADNUM_SYS0_GPIO_A1 1
+#define PADNUM_SYS0_GPIO_A2 2
+#define PADNUM_SYS0_GPIO_A3 3
+
+#endif
--
2.25.1
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply related [flat|nested] 32+ messages in thread* Re: [PATCH v2 04/22] dt-bindings: pinctrl: Add starfive,jhb100-sys0-pinctrl
2026-05-14 11:12 ` [PATCH v2 04/22] dt-bindings: pinctrl: Add starfive,jhb100-sys0-pinctrl Changhuang Liang
@ 2026-05-14 18:52 ` Conor Dooley
0 siblings, 0 replies; 32+ messages in thread
From: Conor Dooley @ 2026-05-14 18:52 UTC (permalink / raw)
To: Changhuang Liang
Cc: Linus Walleij, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Emil Renner Berthing, Paul Walmsley, Albert Ou, Palmer Dabbelt,
Alexandre Ghiti, Philipp Zabel, Bartosz Golaszewski, linux-gpio,
linux-kernel, devicetree, linux-riscv, Lianfeng Ouyang
[-- Attachment #1.1: Type: text/plain, Size: 7765 bytes --]
On Thu, May 14, 2026 at 04:12:00AM -0700, Changhuang Liang wrote:
> Add pinctrl bindings for StarFive JHB100 SoC System-0(sys0) pinctrl
> controller.
>
> Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
> ---
> .../pinctrl/starfive,jhb100-sys0-pinctrl.yaml | 175 ++++++++++++++++++
> .../pinctrl/starfive,jhb100-pinctrl.h | 17 ++
> 2 files changed, 192 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys0-pinctrl.yaml
> create mode 100644 include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys0-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys0-pinctrl.yaml
> new file mode 100644
> index 000000000000..21d3693587fd
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys0-pinctrl.yaml
> @@ -0,0 +1,175 @@
> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pinctrl/starfive,jhb100-sys0-pinctrl.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: StarFive JHB100 System-0 Pin Controller
> +
> +description: |
> + Pinctrl bindings for JHB100 RISC-V SoC from StarFive Technology Ltd.
> +
> + The JHB100 SoC has 13 pinctrl domains - sys0, sys0h, sys1, sys2, per0, per1,
> + per2, per2pok, per3, adc0, adc1, emmc, and vga.
> + This document provides an overview of the "sys0" pinctrl domain.
> +
> + The "sys0" domain has a pin controller which provides
> + - function selection for GPIO pads.
> + - GPIO pad configuration.
> + - GPIO interrupt handling.
> +
> + In the SYS0 Pin Controller, there are 4 multi-function GPIO_PADs. Each of
> + them can be multiplexed to different hardware blocks through function
> + selection and each iopad has a maximum of up to 2 functions - 0 and 1.
> + Function 0 is the default function which is generally the GPIO function
> + (or occasionally, it can be a peripheral signal).
> + Function 1 is the alternate function or peripheral signal that can be
> + routed to the iopad. The function selection is carried out by writing
> + the function number to the iopad function select register.
> +
> + Each iopad is configurable with parameters such as input-enable, internal
> + pull-up/pull-down bias, drive strength, schmitt trigger, slew rate, input
> + debounce nanoseconds, power source and drive type (open-drain or push-pull).
> +
> +maintainers:
> + - Alex Soo <yuklin.soo@starfivetech.com>
Why is Alex the maintainer when you are the sole author?
> +
> +properties:
> + compatible:
> + items:
> + - const: starfive,jhb100-sys0-pinctrl
> +
> + reg:
> + maxItems: 1
> +
> + clocks:
> + maxItems: 1
> +
> + resets:
> + maxItems: 1
> +
> + interrupts:
> + maxItems: 1
> +
> + interrupt-controller: true
> +
> + '#interrupt-cells':
> + const: 3
> +
> + gpio-controller: true
> +
> + '#gpio-cells':
> + const: 3
> +
> + gpio-ranges: true
> +
> + gpio-line-names: true
> +
> +patternProperties:
> + '-grp$':
> + type: object
> + additionalProperties: false
> + patternProperties:
> + '-pins$':
> + type: object
> + description: |
> + A pinctrl node should contain at least one subnode representing the
> + pinctrl groups available in the domain. Each subnode will list the
> + pins it needs, and how they should be configured, with regard to
> + function selection, bias, input enable/disable, input schmitt
> + trigger enable/disable, slew-rate, input debounce nanoseconds,
> + drive-open-drain, drive-push-pull, power-source and drive-strength.
> + allOf:
> + - $ref: /schemas/pinctrl/pincfg-node.yaml
> + - $ref: /schemas/pinctrl/pinmux-node.yaml
> + unevaluatedProperties: false
I think this should be additionalProperties, since you're citing all the
properties you do support below.
> +
> + properties:
> + pins:
> + description:
> + The list of IOs that properties in the pincfg node apply to.
> +
> + function:
> + description:
> + A string containing the name of the function to mux for these
> + pins.
> + enum: [ auxpwrgood, gpio, hbled, pe2rst_out ]
> +
> + bias-disable: true
> +
> + bias-pull-down:
> + type: boolean
> +
> + bias-pull-up:
> + oneOf:
> + - type: boolean
> + - enum: [ 600, 900, 1200, 2000 ]
> + description: Pull up RSEL type resistance values (in ohms)
> + description:
> + For normal pull up type there is no need to specify a resistance
> + value, hence this can be specified as a boolean property.
> + For RSEL pull up type a resistance value (in ohms) can be added.
> +
> + drive-open-drain: true
> +
> + drive-push-pull: true
> +
> + drive-strength:
> + enum: [ 2, 4, 8, 12 ]
> +
> + drive-strength-microamp:
> + enum: [ 2000, 4000, 8000, 12000 ]
> +
> + input-debounce-nanoseconds:
> + minimum: 0
> + maximum: 4294967295
> +
> + input-disable: true
> +
> + input-enable: true
> +
> + input-schmitt-enable: true
> +
> + input-schmitt-disable: true
> +
> + power-source:
> + enum: [ 0, 1, 2 ]
> +
> + slew-rate:
> + enum: [ 0, 1 ]
> + default: 0
> + description: |
> + 0: slow (half frequency)
> + 1: fast
> +
> +required:
> + - compatible
> + - reg
> + - resets
> + - interrupts
> + - interrupt-controller
> + - '#interrupt-cells'
> + - gpio-controller
> + - '#gpio-cells'
> + - gpio-ranges
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + soc {
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + pinctrl_sys0: pinctrl@13080000 {
> + compatible = "starfive,jhb100-sys0-pinctrl";
> + reg = <0x0 0x13080000 0x0 0x800>;
> + resets = <&sys0crg 2>;
> + interrupts = <56>;
> + interrupt-controller;
> + #interrupt-cells = <3>;
> + gpio-controller;
> + #gpio-cells = <3>;
> + gpio-ranges = <&pinctrl_sys0 0 0 0 4>;
> + };
> + };
> diff --git a/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h b/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h
> new file mode 100644
> index 000000000000..6d8f5516a178
> --- /dev/null
> +++ b/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h
> @@ -0,0 +1,17 @@
> +/* SPDX-License-Identifier: GPL-2.0 OR MIT */
> +/*
> + * Copyright (C) 2022 StarFive Technology Co., Ltd.
> + *
> + * Author: Changhuang Liang <changhuang.liang@starfivetech.com>
> + */
> +
> +#ifndef __DT_BINDINGS_PINCTRL_STARFIVE_JHB100_H__
> +#define __DT_BINDINGS_PINCTRL_STARFIVE_JHB100_H__
> +
> +/* sys0 pad numbers */
> +#define PADNUM_SYS0_GPIO_A0 0
> +#define PADNUM_SYS0_GPIO_A1 1
> +#define PADNUM_SYS0_GPIO_A2 2
> +#define PADNUM_SYS0_GPIO_A3 3
Does this provide any actual value? Across the whole series, most
numbers you put in this binding headers do not appear in any drivers
at all. Seems like these defines should appear in the dts directly?
pw-bot: changes-requested
Cheers,
Conor.
> +
> +#endif
> --
> 2.25.1
>
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
[-- Attachment #2: Type: text/plain, Size: 161 bytes --]
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply [flat|nested] 32+ messages in thread
* [PATCH v2 05/22] pinctrl: starfive: Add StarFive JHB100 sys0 controller driver
2026-05-14 11:11 [PATCH v2 00/22] Add basic pinctrl drivers for JHB100 SoC Changhuang Liang
` (3 preceding siblings ...)
2026-05-14 11:12 ` [PATCH v2 04/22] dt-bindings: pinctrl: Add starfive,jhb100-sys0-pinctrl Changhuang Liang
@ 2026-05-14 11:12 ` Changhuang Liang
2026-05-14 11:12 ` [PATCH v2 06/22] dt-bindings: pinctrl: Add starfive,jhb100-sys0h-pinctrl Changhuang Liang
` (16 subsequent siblings)
21 siblings, 0 replies; 32+ messages in thread
From: Changhuang Liang @ 2026-05-14 11:12 UTC (permalink / raw)
To: Linus Walleij, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Emil Renner Berthing, Paul Walmsley, Albert Ou, Palmer Dabbelt,
Alexandre Ghiti, Philipp Zabel, Bartosz Golaszewski
Cc: linux-gpio, linux-kernel, devicetree, linux-riscv,
Lianfeng Ouyang, Changhuang Liang
Add pinctrl driver for StarFive JHB100 SoC System-0(sys0) pinctrl
controller.
Co-developed-by: Lianfeng Ouyang <lianfeng.ouyang@starfivetech.com>
Signed-off-by: Lianfeng Ouyang <lianfeng.ouyang@starfivetech.com>
Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
---
MAINTAINERS | 9 +
drivers/pinctrl/starfive/Kconfig | 19 +
drivers/pinctrl/starfive/Makefile | 3 +
.../starfive/pinctrl-starfive-jhb100-sys0.c | 123 ++
.../starfive/pinctrl-starfive-jhb100.c | 1579 +++++++++++++++++
.../starfive/pinctrl-starfive-jhb100.h | 152 ++
6 files changed, 1885 insertions(+)
create mode 100644 drivers/pinctrl/starfive/pinctrl-starfive-jhb100-sys0.c
create mode 100644 drivers/pinctrl/starfive/pinctrl-starfive-jhb100.c
create mode 100644 drivers/pinctrl/starfive/pinctrl-starfive-jhb100.h
diff --git a/MAINTAINERS b/MAINTAINERS
index 47e4b368347f..f56721b4cbd1 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -25607,6 +25607,15 @@ S: Supported
F: Documentation/devicetree/bindings/interrupt-controller/starfive,jhb100-intc.yaml
F: drivers/irqchip/irq-starfive-jhb100-intc.c
+STARFIVE JHB100 PINCTRL DRIVERS
+M: Changhuang Liang <changhuang.liang@starfivetech.com>
+M: Lianfeng Ouyang <lianfeng.ouyang@starfivetech.com>
+L: linux-gpio@vger.kernel.org
+S: Maintained
+F: Documentation/devicetree/bindings/pinctrl/starfive,jhb1*.yaml
+F: drivers/pinctrl/starfive/pinctrl-starfive-jhb1*
+F: include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h
+
STARFIVE JHB100 RESET CONTROLLER DRIVERS
M: Changhuang Liang <changhuang.liang@starfivetech.com>
S: Maintained
diff --git a/drivers/pinctrl/starfive/Kconfig b/drivers/pinctrl/starfive/Kconfig
index a9a7cb101684..548a1b133f81 100644
--- a/drivers/pinctrl/starfive/Kconfig
+++ b/drivers/pinctrl/starfive/Kconfig
@@ -47,3 +47,22 @@ config PINCTRL_STARFIVE_JH7110_AON
This also provides an interface to the GPIO pins not used by other
peripherals supporting inputs, outputs, configuring pull-up/pull-down
and interrupts on input changes.
+
+config PINCTRL_STARFIVE_JHB100
+ bool
+ select GENERIC_PINCTRL
+ select GPIOLIB
+ select GPIOLIB_IRQCHIP
+ select OF_GPIO
+
+config PINCTRL_STARFIVE_JHB100_SYS0
+ tristate "StarFive JHB100 SoC System-0 pinctrl and GPIO driver"
+ depends on ARCH_STARFIVE || COMPILE_TEST
+ depends on OF
+ select PINCTRL_STARFIVE_JHB100
+ default ARCH_STARFIVE
+ help
+ Say yes here to support system-0 pin control on the StarFive JHB100 SoC.
+ This also provides an interface to the GPIO pins not used by other
+ peripherals supporting inputs, outputs, configuring pull-up/pull-down
+ and interrupts on input changes.
diff --git a/drivers/pinctrl/starfive/Makefile b/drivers/pinctrl/starfive/Makefile
index ee0d32d085cb..c0d368f413bc 100644
--- a/drivers/pinctrl/starfive/Makefile
+++ b/drivers/pinctrl/starfive/Makefile
@@ -5,3 +5,6 @@ obj-$(CONFIG_PINCTRL_STARFIVE_JH7100) += pinctrl-starfive-jh7100.o
obj-$(CONFIG_PINCTRL_STARFIVE_JH7110) += pinctrl-starfive-jh7110.o
obj-$(CONFIG_PINCTRL_STARFIVE_JH7110_SYS) += pinctrl-starfive-jh7110-sys.o
obj-$(CONFIG_PINCTRL_STARFIVE_JH7110_AON) += pinctrl-starfive-jh7110-aon.o
+
+obj-$(CONFIG_PINCTRL_STARFIVE_JHB100) += pinctrl-starfive-jhb100.o
+obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_SYS0) += pinctrl-starfive-jhb100-sys0.o
diff --git a/drivers/pinctrl/starfive/pinctrl-starfive-jhb100-sys0.c b/drivers/pinctrl/starfive/pinctrl-starfive-jhb100-sys0.c
new file mode 100644
index 000000000000..d86a82eb5e05
--- /dev/null
+++ b/drivers/pinctrl/starfive/pinctrl-starfive-jhb100-sys0.c
@@ -0,0 +1,123 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Pinctrl / GPIO driver for StarFive JHB100 SoC System-0 domain
+ *
+ * Copyright (C) 2024 StarFive Technology Co., Ltd.
+ * Author: Alex Soo <yuklin.soo@starfivetech.com>
+ *
+ */
+
+#include <dt-bindings/pinctrl/starfive,jhb100-pinctrl.h>
+#include <linux/mod_devicetable.h>
+#include <linux/platform_device.h>
+
+#include "pinctrl-starfive-jhb100.h"
+
+static const struct jhb100_pin_layout_desc jhb100_sys0_pl_desc[] = {
+ { .pin_start = 0, .pin_cnt = 3, .name = "gpio", .gpio_func_sel = 0, },
+ { .pin_start = 3, .pin_cnt = 1, .name = "bmcpcierp_pe2rst_out", .gpio_func_sel = 1, },
+ { .pin_start = 4, .pin_cnt = 1, .name = "testen", .gpio_func_sel = -1, },
+ { .pin_start = 5, .pin_cnt = 1, .name = "syspok_in", .gpio_func_sel = -1, },
+ { .pin_start = 6, .pin_cnt = 1, .name = "sysrstn_in", .gpio_func_sel = -1, },
+ { .pin_start = 7, .pin_cnt = 1, .name = "perstn0_in", .gpio_func_sel = -1, },
+ { .pin_start = 8, .pin_cnt = 1, .name = "perstn1_in", .gpio_func_sel = -1, },
+ { .pin_start = 9, .pin_cnt = 1, .name = "aprstn_out", .gpio_func_sel = -1, },
+ { .pin_start = 10, .pin_cnt = 1, .name = "pcierp_wake", .gpio_func_sel = -1, },
+ { 0xff },
+};
+
+static struct config_reg_layout_desc jhb100_sys0_pinctrl_crl_desc[] = {
+ {
+ .pin_start = 0,
+ .pin_cnt = 4,
+ .drive_strength_2bit = { .shift = 0, .width = 2 },
+ .input_enable = { .shift = 2, .width = 1 },
+ .pull_down = { .shift = 3, .width = 1 },
+ .pull_up = { .shift = 4, .width = 1 },
+ .slew_rate = { .shift = 5, .width = 1 },
+ .schmitt_trigger_select = { .shift = 6, .width = 1 },
+ .reserved = { .shift = 7, .width = 8 },
+ .debounce_width = { .shift = 15, .width = 17 },
+ },
+ {
+ .pin_start = 4,
+ .pin_cnt = 5,
+ .schmitt_trigger_select = { .shift = 0, .width = 1 },
+ .reserved = { .shift = 1, .width = 31 },
+ },
+ {
+ .pin_start = 9,
+ .pin_cnt = 1,
+ .drive_strength_2bit = { .shift = 0, .width = 2 },
+ .slew_rate = { .shift = 2, .width = 1 },
+ .reserved = { .shift = 3, .width = 29 },
+ },
+ {
+ .pin_start = 10,
+ .pin_cnt = 1,
+ .drive_strength_2bit = { .shift = 0, .width = 2 },
+ .input_enable = { .shift = 2, .width = 1 },
+ .pull_down = { .shift = 3, .width = 1 },
+ .pull_up = { .shift = 4, .width = 1 },
+ .slew_rate = { .shift = 5, .width = 1 },
+ .schmitt_trigger_select = { .shift = 6, .width = 1 },
+ .reserved = { .shift = 7, .width = 25 },
+ },
+ { 0xff },
+};
+
+struct starfive_pinctrl_regs jhb100_sys0_pinctrl_regs = {
+ .func_sel = { .reg = 0x44, .width_per_pin = 2 },
+ .config = 0x0c,
+ .output = 0x38,
+ .output_en = 0x3c,
+ .gpio_status = 0x40,
+ .irq_en = 0x48,
+ .irq_status = 0x4c,
+ .irq_clr = 0x50,
+ .irq_trigger = 0x54,
+ .irq_level = 0x58,
+ .irq_both_edge = 0x5c,
+ .irq_edge = 0x60,
+};
+
+static const struct jhb100_pinctrl_func_maps jhb100_func_maps_sys0[] = {
+ { .func = "auxpwrgood", .val = 1 },
+ { .func = "gpio", .val = 0,
+ .max_pin = JHB100_FUNC_MAPS_MAX_PIN(PADNUM_PER3_GPIO_E2) },
+ { .func = "gpio", .val = 1,
+ .max_pin = JHB100_FUNC_MAPS_MAX_PIN(PADNUM_PER3_GPIO_E3) },
+ { .func = "hbled", .val = 1 },
+ { .func = "pe2rst_out", .val = 0 },
+};
+
+static const struct jhb100_pinctrl_domain_info jhb100_sys0_pinctrl_info = {
+ .name = "jhb100-sys0",
+ .pl_desc = jhb100_sys0_pl_desc,
+ .crl_desc = jhb100_sys0_pinctrl_crl_desc,
+ .regs = &jhb100_sys0_pinctrl_regs,
+ .fmaps = jhb100_func_maps_sys0,
+ .num_maps = ARRAY_SIZE(jhb100_func_maps_sys0),
+};
+
+static const struct of_device_id jhb100_sys0_pinctrl_of_match[] = {
+ {
+ .compatible = "starfive,jhb100-sys0-pinctrl",
+ .data = &jhb100_sys0_pinctrl_info,
+ },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, jhb100_sys0_pinctrl_of_match);
+
+static struct platform_driver jhb100_sys0_pinctrl_driver = {
+ .probe = jhb100_pinctrl_probe,
+ .driver = {
+ .name = "starfive-jhb100-sys0-pinctrl",
+ .of_match_table = jhb100_sys0_pinctrl_of_match,
+ },
+};
+module_platform_driver(jhb100_sys0_pinctrl_driver);
+
+MODULE_DESCRIPTION("Pinctrl driver for StarFive JHB100 SoC System-0 domain");
+MODULE_AUTHOR("Alex Soo <yuklin.soo@starfivetech.com>");
+MODULE_LICENSE("GPL");
diff --git a/drivers/pinctrl/starfive/pinctrl-starfive-jhb100.c b/drivers/pinctrl/starfive/pinctrl-starfive-jhb100.c
new file mode 100644
index 000000000000..e928cc9e4c80
--- /dev/null
+++ b/drivers/pinctrl/starfive/pinctrl-starfive-jhb100.c
@@ -0,0 +1,1579 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Pinctrl / GPIO driver for StarFive JHB100 SoC
+ *
+ * Copyright (C) 2024 StarFive Technology Co., Ltd.
+ * Author: Alex Soo <yuklin.soo@starfivetech.com>
+ *
+ */
+
+#include <linux/bitfield.h>
+#include <linux/bits.h>
+#include <linux/clk.h>
+#include <linux/gpio/driver.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/minmax.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/reset.h>
+#include <linux/seq_file.h>
+#include <linux/spinlock.h>
+#include <linux/string.h>
+#include <linux/sort.h>
+
+#include <linux/pinctrl/consumer.h>
+#include <linux/pinctrl/pinconf.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinmux.h>
+
+#include "../core.h"
+#include "../pinconf.h"
+#include "../pinctrl-utils.h"
+#include "../pinmux.h"
+#include "pinctrl-starfive-jhb100.h"
+
+#define GPOUT_LOW 0
+#define GPOUT_HIGH 1
+
+#define GPOEN_ENABLE 0
+#define GPOEN_DISABLE 1
+
+#define JHB100_DEBOUNCE_WIDTH_STAGES_MAX 0x1FFFFU
+#define JHB100_DEBOUNCE_WIDTH_STAGE_NS 80
+
+/* mode select */
+#define JHB100_PUSH_PULL 0
+#define JHB100_OPEN_DRAIN 1
+#define JHB100_LEGACY_FAST_MODE_PLUS 2
+#define JHB100_LEGACY_FAST_MODE 3
+
+/* i2c open-drain pull-up select */
+#define JHB100_I2C_OPEN_DRAIN_PU_600_OHMS 0
+#define JHB100_I2C_OPEN_DRAIN_PU_900_OHMS 1
+#define JHB100_I2C_OPEN_DRAIN_PU_1200_OHMS 2
+#define JHB100_I2C_OPEN_DRAIN_PU_2000_OHMS 3
+
+#define JHB100_NR_GPIOS_PER_BANK 32
+
+struct field_info {
+ const char *name;
+ unsigned int shift;
+ unsigned int width;
+ unsigned int end;
+};
+
+static int jhb100_map_get_func_val(struct jhb100_pinctrl *sfp, const char *function,
+ unsigned int pin)
+{
+ const struct jhb100_pinctrl_func_maps *fmaps = sfp->info->fmaps;
+ size_t num = sfp->info->num_maps;
+
+ for (int i = 0; i < num; i++) {
+ if (!strcmp(function, fmaps[i].func)) {
+ if (!fmaps[i].max_pin)
+ return fmaps[i].val;
+
+ if (pin < fmaps[i].max_pin)
+ return fmaps[i].val;
+
+ continue;
+ }
+ }
+
+ return -EINVAL;
+}
+
+static struct config_reg_layout_desc *get_crl_desc_by_pin(struct jhb100_pinctrl *sfp,
+ unsigned int pin)
+{
+ struct config_reg_layout_desc *crl_desc = sfp->info->crl_desc;
+ unsigned int i = 0;
+
+ do {
+ if (pin >= crl_desc[i].pin_start &&
+ pin < crl_desc[i].pin_start + crl_desc[i].pin_cnt)
+ return &crl_desc[i];
+ } while (crl_desc[i++].pin_start != 0xff);
+
+ return NULL;
+}
+
+static inline struct jhb100_gpio_bank *jhb100_gc_to_bank(struct gpio_chip *gc)
+{
+ return container_of(gc, struct jhb100_gpio_bank, gc);
+}
+
+static unsigned int jhb100_gpio_to_pin(struct gpio_chip *gc, unsigned int gpio)
+{
+ struct jhb100_gpio_bank *bank = jhb100_gc_to_bank(gc);
+
+ return bank->id * JHB100_NR_GPIOS_PER_BANK + gpio;
+}
+
+static const struct pinctrl_ops jhb100_pinctrl_ops = {
+ .get_groups_count = pinctrl_generic_get_group_count,
+ .get_group_name = pinctrl_generic_get_group_name,
+ .get_group_pins = pinctrl_generic_get_group_pins,
+ .dt_node_to_map = pinctrl_generic_pins_function_dt_node_to_map,
+ .dt_free_map = pinctrl_utils_free_map,
+};
+
+static void jhb100_set_gpioval(struct jhb100_pinctrl *sfp, unsigned int pin,
+ unsigned int val)
+{
+ const struct jhb100_pinctrl_domain_info *info = sfp->info;
+ unsigned int offset = 4 * (pin / 32);
+ unsigned int shift = 1 * (pin % 32);
+ unsigned int fs_offset = 4 * (pin / 16);
+ unsigned int fs_shift = 2 * (pin % 16);
+ u32 func_sel_mask;
+ u32 dout, doen, fs;
+ void __iomem *reg_gpio_o;
+ void __iomem *reg_gpio_oen;
+ void __iomem *reg_gpio_func_sel;
+ unsigned long flags;
+
+ reg_gpio_o = sfp->base + info->regs->output + offset;
+ reg_gpio_oen = sfp->base + info->regs->output_en + offset;
+ reg_gpio_func_sel = sfp->base + info->regs->func_sel.reg + fs_offset;
+
+ func_sel_mask = GENMASK(info->regs->func_sel.width_per_pin - 1, 0) << fs_shift;
+ dout = val << shift;
+ doen = 0;
+
+ raw_spin_lock_irqsave(&sfp->lock, flags);
+ fs = readl_relaxed(reg_gpio_func_sel);
+ if (fs & func_sel_mask) {
+ fs &= ~func_sel_mask;
+ writel_relaxed(fs, reg_gpio_func_sel);
+ }
+ dout |= readl_relaxed(reg_gpio_o) & ~BIT(shift);
+ writel_relaxed(dout, reg_gpio_o);
+ doen |= readl_relaxed(reg_gpio_oen) & ~BIT(shift);
+ writel_relaxed(doen, reg_gpio_oen);
+ raw_spin_unlock_irqrestore(&sfp->lock, flags);
+}
+
+static void jhb100_set_function(struct jhb100_pinctrl *sfp,
+ unsigned int pin, u8 func)
+{
+ struct starfive_pinctrl_regs *pinctrl_regs = sfp->info->regs;
+ void __iomem *func_sel_reg;
+ unsigned long flags;
+ u32 func_sel_mask;
+ u32 func_sel_val;
+ unsigned int offset = 4 * (pin / (32 / pinctrl_regs->func_sel.width_per_pin));
+ unsigned int shift = pinctrl_regs->func_sel.width_per_pin *
+ (pin % (32 / pinctrl_regs->func_sel.width_per_pin));
+
+ if (!pinctrl_regs->func_sel.reg || !pinctrl_regs->func_sel.width_per_pin)
+ return;
+
+ func_sel_reg = sfp->base + pinctrl_regs->func_sel.reg + offset;
+ func_sel_mask = GENMASK(pinctrl_regs->func_sel.width_per_pin - 1, 0) << shift;
+ func_sel_val = func << shift;
+
+ raw_spin_lock_irqsave(&sfp->lock, flags);
+ func_sel_val |= readl_relaxed(func_sel_reg) & ~func_sel_mask;
+ writel_relaxed(func_sel_val, func_sel_reg);
+ raw_spin_unlock_irqrestore(&sfp->lock, flags);
+}
+
+static int jhb100_set_one_pin_mux(struct jhb100_pinctrl *sfp,
+ unsigned int pin,
+ u8 func,
+ int val)
+{
+ const struct pinctrl_pin_desc *desc = &sfp->pins[pin];
+ struct device *dev = sfp->dev;
+ s8 gpio_func_sel = sfp->gpio_func_sel_arr[pin];
+
+ jhb100_set_function(sfp, pin, func);
+
+ if (pin < sfp->ngpios && (val == 0 || val == 1)) {
+ if (func == gpio_func_sel)
+ jhb100_set_gpioval(sfp, pin, val);
+ else
+ dev_err(dev, "pin (%s) is not a GPIO. func=%d/%d\n",
+ desc->name, func, gpio_func_sel);
+ }
+
+ return 0;
+}
+
+static int jhb100_set_mux(struct pinctrl_dev *pctldev,
+ unsigned int fsel, unsigned int gsel)
+{
+ struct jhb100_pinctrl *sfp = pinctrl_dev_get_drvdata(pctldev);
+ const struct group_desc *group;
+ unsigned int i;
+ const char **functions;
+
+ group = pinctrl_generic_get_group(pctldev, gsel);
+ if (!group)
+ return -EINVAL;
+
+ functions = group->data;
+
+ for (i = 0; i < group->grp.npins; i++) {
+ int function;
+
+ function = jhb100_map_get_func_val(sfp, functions[i], group->grp.pins[i]);
+ if (function < 0) {
+ dev_err(pctldev->dev, "invalid function %s\n", functions[i]);
+ return function;
+ }
+
+ jhb100_set_one_pin_mux(sfp, group->grp.pins[i], function, -1);
+ }
+
+ return 0;
+}
+
+static const struct pinmux_ops jhb100_pinmux_ops = {
+ .get_functions_count = pinmux_generic_get_function_count,
+ .get_function_name = pinmux_generic_get_function_name,
+ .get_function_groups = pinmux_generic_get_function_groups,
+ .set_mux = jhb100_set_mux,
+};
+
+static const u8 jhb100_drive_strength_ma[4] = { 2, 4, 8, 12 };
+
+static const u8 jhb100_drive_strength_ma_3bit[8] = { 2, 5, 8, 10, 14, 16, 18, 20 };
+
+static u32 jhb100_padcfg_ds_to_mA(u32 padcfg)
+{
+ return jhb100_drive_strength_ma[padcfg];
+}
+
+static u32 jhb100_padcfg_ds_to_mA_3bit(u32 padcfg)
+{
+ return jhb100_drive_strength_ma_3bit[padcfg];
+}
+
+static u32 jhb100_padcfg_ds_to_uA(u32 padcfg)
+{
+ return (jhb100_drive_strength_ma[padcfg] * 1000);
+}
+
+static u32 jhb100_padcfg_ds_to_uA_3bit(u32 padcfg)
+{
+ return (jhb100_drive_strength_ma_3bit[padcfg] * 1000);
+}
+
+static u32 jhb100_padcfg_ds_from_mA(u32 v)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(jhb100_drive_strength_ma); i++) {
+ if (v <= jhb100_drive_strength_ma[i])
+ break;
+ }
+ return i;
+}
+
+static u32 jhb100_padcfg_ds_from_mA_3bit(u32 v)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(jhb100_drive_strength_ma_3bit); i++) {
+ if (v <= jhb100_drive_strength_ma_3bit[i])
+ break;
+ }
+ return i;
+}
+
+static u32 jhb100_padcfg_ds_from_uA(u32 v)
+{
+ /* Convert from uA to mA */
+ v /= 1000;
+
+ return jhb100_padcfg_ds_from_mA(v);
+}
+
+static u32 jhb100_padcfg_ds_from_uA_3bit(u32 v)
+{
+ /* Convert from uA to mA */
+ v /= 1000;
+
+ return jhb100_padcfg_ds_from_mA_3bit(v);
+}
+
+static void jhb100_padcfg_rmw(struct jhb100_pinctrl *sfp,
+ unsigned int pin, u32 mask, u32 value)
+{
+ void __iomem *reg;
+ unsigned int offset;
+ unsigned long flags;
+ int padcfg_base;
+
+ padcfg_base = sfp->info->regs->config;
+
+ offset = 4 * pin;
+
+ reg = sfp->base + padcfg_base + offset;
+
+ value &= mask;
+ raw_spin_lock_irqsave(&sfp->lock, flags);
+ value |= readl_relaxed(reg) & ~mask;
+ writel_relaxed(value, reg);
+ raw_spin_unlock_irqrestore(&sfp->lock, flags);
+}
+
+static int jhb100_pinconf_get(struct pinctrl_dev *pctldev,
+ unsigned int pin, unsigned long *config)
+{
+ struct jhb100_pinctrl *sfp = pinctrl_dev_get_drvdata(pctldev);
+ int param = pinconf_to_config_param(*config);
+ struct device *dev = sfp->dev;
+ struct config_reg_layout_desc *crl_desc;
+ unsigned int offset;
+ u32 padcfg, arg;
+ bool enabled;
+ int padcfg_base;
+
+ padcfg_base = sfp->info->regs->config;
+
+ offset = 4 * pin;
+
+ if (pin <= sfp->npins)
+ padcfg = readl_relaxed(sfp->base + padcfg_base + offset);
+ else
+ return -EINVAL;
+
+ crl_desc = get_crl_desc_by_pin(sfp, pin);
+ if (!crl_desc) {
+ dev_err(dev, "pin %d can't not found reg layout descriptor\n", pin);
+ return -EINVAL;
+ }
+
+ switch (param) {
+ case PIN_CONFIG_BIAS_DISABLE:
+ arg = 0;
+
+ if (!RL_DESC_SUPPORTED(crl_desc, pull_down) ||
+ !RL_DESC_SUPPORTED(crl_desc, pull_up))
+ return -EOPNOTSUPP;
+
+ enabled = !(padcfg & (RL_DESC_GENMASK(crl_desc, pull_down) |
+ RL_DESC_GENMASK(crl_desc, pull_up)));
+ break;
+ case PIN_CONFIG_BIAS_PULL_DOWN:
+ arg = 1;
+
+ if (!RL_DESC_SUPPORTED(crl_desc, pull_down))
+ return -EOPNOTSUPP;
+
+ enabled = (padcfg & RL_DESC_GENMASK(crl_desc, pull_down))
+ >> RL_DESC_SHIFT(crl_desc, pull_down);
+ break;
+ case PIN_CONFIG_BIAS_PULL_UP:
+ arg = 1;
+
+ if (!RL_DESC_SUPPORTED(crl_desc, pull_up))
+ return -EOPNOTSUPP;
+
+ enabled = (padcfg & RL_DESC_GENMASK(crl_desc, pull_up))
+ >> RL_DESC_SHIFT(crl_desc, pull_up);
+ break;
+ case PIN_CONFIG_DRIVE_STRENGTH:
+ enabled = true;
+
+ if (RL_DESC_SUPPORTED(crl_desc, drive_strength_2bit))
+ arg = jhb100_padcfg_ds_to_mA(padcfg <<
+ RL_DESC_SHIFT(crl_desc,
+ drive_strength_2bit));
+ else if (RL_DESC_SUPPORTED(crl_desc, drive_strength_3bit))
+ arg = jhb100_padcfg_ds_to_mA_3bit(padcfg <<
+ RL_DESC_SHIFT(crl_desc,
+ drive_strength_3bit));
+ else
+ return -EOPNOTSUPP;
+ break;
+ case PIN_CONFIG_DRIVE_STRENGTH_UA:
+ enabled = true;
+
+ if (RL_DESC_SUPPORTED(crl_desc, drive_strength_2bit))
+ arg = jhb100_padcfg_ds_to_uA(padcfg
+ << RL_DESC_SHIFT(crl_desc, drive_strength_2bit));
+ else if (RL_DESC_SUPPORTED(crl_desc, drive_strength_3bit))
+ arg = jhb100_padcfg_ds_to_uA_3bit(padcfg
+ << RL_DESC_SHIFT(crl_desc, drive_strength_3bit));
+ else
+ return -EOPNOTSUPP;
+ break;
+ case PIN_CONFIG_INPUT_ENABLE:
+ if (!RL_DESC_SUPPORTED(crl_desc, input_enable))
+ return -EOPNOTSUPP;
+
+ enabled = (padcfg & RL_DESC_GENMASK(crl_desc, input_enable))
+ >> RL_DESC_SHIFT(crl_desc, input_enable);
+ arg = enabled;
+ break;
+ case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
+ if (!RL_DESC_SUPPORTED(crl_desc, schmitt_trigger_select))
+ return -EOPNOTSUPP;
+
+ enabled = (padcfg & RL_DESC_GENMASK(crl_desc, schmitt_trigger_select))
+ >> RL_DESC_SHIFT(crl_desc, schmitt_trigger_select);
+ arg = enabled;
+ break;
+ case PIN_CONFIG_SLEW_RATE:
+ enabled = true;
+
+ if (!RL_DESC_SUPPORTED(crl_desc, slew_rate))
+ return -EOPNOTSUPP;
+
+ arg = (padcfg & RL_DESC_GENMASK(crl_desc, slew_rate))
+ >> RL_DESC_SHIFT(crl_desc, slew_rate);
+ break;
+ default:
+ return -ENOTSUPP;
+ }
+
+ *config = pinconf_to_config_packed(param, arg);
+ return enabled ? 0 : -EINVAL;
+}
+
+static int jhb100_pinconf_set(struct pinctrl_dev *pctldev,
+ unsigned int gpio, unsigned long *config,
+ unsigned int num_configs)
+{
+ struct jhb100_pinctrl *sfp = pinctrl_dev_get_drvdata(pctldev);
+ struct device *dev = sfp->dev;
+ struct config_reg_layout_desc *crl_desc;
+ u32 param;
+ u32 arg;
+ u32 value;
+ u32 mask;
+ int i;
+
+ crl_desc = get_crl_desc_by_pin(sfp, gpio);
+ if (!crl_desc) {
+ dev_err(dev, "pin %d can't not found reg layout descriptor\n", gpio);
+ return -EINVAL;
+ }
+
+ for (i = 0; i < num_configs; i++) {
+ param = pinconf_to_config_param(config[i]);
+ arg = pinconf_to_config_argument(config[i]);
+ switch (param) {
+ case PIN_CONFIG_BIAS_DISABLE:
+ if (!RL_DESC_SUPPORTED(crl_desc, pull_down) ||
+ !RL_DESC_SUPPORTED(crl_desc, pull_up))
+ return -EOPNOTSUPP;
+
+ mask = RL_DESC_GENMASK(crl_desc, pull_down) |
+ RL_DESC_GENMASK(crl_desc, pull_up);
+ value = 0;
+ break;
+ case PIN_CONFIG_BIAS_PULL_DOWN:
+ if (!RL_DESC_SUPPORTED(crl_desc, pull_down) ||
+ !RL_DESC_SUPPORTED(crl_desc, pull_up))
+ return -EOPNOTSUPP;
+
+ mask = RL_DESC_GENMASK(crl_desc, pull_down) |
+ RL_DESC_GENMASK(crl_desc, pull_up);
+ value = RL_DESC_GENMASK(crl_desc, pull_down);
+ break;
+ case PIN_CONFIG_BIAS_PULL_UP:
+ if (!RL_DESC_SUPPORTED(crl_desc, pull_down) ||
+ !RL_DESC_SUPPORTED(crl_desc, pull_up))
+ return -EOPNOTSUPP;
+
+ mask = RL_DESC_GENMASK(crl_desc, pull_down) |
+ RL_DESC_GENMASK(crl_desc, pull_up);
+ value = RL_DESC_GENMASK(crl_desc, pull_up);
+ break;
+ case PIN_CONFIG_DRIVE_PUSH_PULL:
+ return 0;
+ case PIN_CONFIG_INPUT_ENABLE:
+ if (!RL_DESC_SUPPORTED(crl_desc, input_enable))
+ return -EOPNOTSUPP;
+
+ mask = RL_DESC_GENMASK(crl_desc, input_enable);
+ value = arg ? RL_DESC_GENMASK(crl_desc, input_enable) : 0;
+ break;
+ case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
+ if (!RL_DESC_SUPPORTED(crl_desc, schmitt_trigger_select))
+ return -EOPNOTSUPP;
+
+ mask = RL_DESC_GENMASK(crl_desc, schmitt_trigger_select);
+ value = arg ? RL_DESC_GENMASK(crl_desc, schmitt_trigger_select) : 0;
+ break;
+ case PIN_CONFIG_INPUT_DEBOUNCE_NS:
+ u32 debounce_stage;
+
+ if (!RL_DESC_SUPPORTED(crl_desc, debounce_width))
+ return -EOPNOTSUPP;
+
+ mask = RL_DESC_GENMASK(crl_desc, debounce_width);
+
+ debounce_stage = arg ? arg / JHB100_DEBOUNCE_WIDTH_STAGE_NS : 0;
+ debounce_stage = umin(debounce_stage, JHB100_DEBOUNCE_WIDTH_STAGES_MAX);
+
+ value = (debounce_stage << RL_DESC_SHIFT(crl_desc, debounce_width));
+ break;
+ case PIN_CONFIG_POWER_SOURCE:
+ if (!RL_DESC_SUPPORTED(crl_desc, vsel))
+ return -EOPNOTSUPP;
+
+ mask = RL_DESC_GENMASK(crl_desc, vsel);
+ value = arg ? arg << RL_DESC_SHIFT(crl_desc, vsel) : 0;
+ break;
+ default:
+ return -ENOTSUPP;
+ }
+
+ jhb100_padcfg_rmw(sfp, gpio, mask, value);
+ }
+
+ return 0;
+}
+
+static int jhb100_pinconf_group_get(struct pinctrl_dev *pctldev,
+ unsigned int gsel,
+ unsigned long *config)
+{
+ const struct group_desc *group;
+
+ group = pinctrl_generic_get_group(pctldev, gsel);
+ if (!group)
+ return -EINVAL;
+
+ return jhb100_pinconf_get(pctldev, group->grp.pins[0], config);
+}
+
+static int jhb100_pincfg_group_vref(const struct group_desc *group, struct jhb100_pinctrl *sfp,
+ u32 arg)
+{
+ struct pinvref_reg *vref = &sfp->info->regs->vref;
+ u32 i = 0, pin;
+
+ while (vref->pv_desc[i].name) {
+ if (!strstr(group->grp.name, vref->pv_desc[i].name)) {
+ i++;
+ continue;
+ }
+
+ if (group->grp.npins != vref->pv_desc[i].num_pins)
+ return -EOPNOTSUPP;
+
+ for (pin = 0; pin < group->grp.npins; pin++) {
+ if (group->grp.pins[pin] != vref->pv_desc[i].pin_grp[pin])
+ return -EOPNOTSUPP;
+ }
+
+ if (vref->pv_desc[pin].range & BIT(arg))
+ writel(arg, sfp->base + vref->reg + i * 4);
+
+ break;
+ }
+
+ return 0;
+}
+
+static int jhb100_pinconf_group_set(struct pinctrl_dev *pctldev,
+ unsigned int gsel,
+ unsigned long *configs,
+ unsigned int num_configs)
+{
+ struct jhb100_pinctrl *sfp = pinctrl_dev_get_drvdata(pctldev);
+ struct device *dev = sfp->dev;
+ struct config_reg_layout_desc *crl_desc;
+ const struct group_desc *group;
+ u32 mask, value;
+ int i;
+
+ group = pinctrl_generic_get_group(pctldev, gsel);
+ if (!group)
+ return -EINVAL;
+
+ mask = 0;
+ value = 0;
+ for (i = 0; i < num_configs; i++) {
+ int param = pinconf_to_config_param(configs[i]);
+ u32 arg = pinconf_to_config_argument(configs[i]);
+
+ crl_desc = get_crl_desc_by_pin(sfp, group->grp.pins[0]);
+ if (!crl_desc) {
+ dev_err(dev, "pin %d can't not found reg layout descriptor\n",
+ group->grp.pins[i]);
+ return -EINVAL;
+ }
+
+ switch (param) {
+ case PIN_CONFIG_BIAS_DISABLE:
+ if (!RL_DESC_SUPPORTED(crl_desc, pull_down) ||
+ !RL_DESC_SUPPORTED(crl_desc, pull_up))
+ return -EOPNOTSUPP;
+
+ mask |= RL_DESC_GENMASK(crl_desc, pull_down) |
+ RL_DESC_GENMASK(crl_desc, pull_up);
+ value &= ~(RL_DESC_GENMASK(crl_desc, pull_down) |
+ RL_DESC_GENMASK(crl_desc, pull_up));
+ break;
+ case PIN_CONFIG_BIAS_PULL_DOWN:
+ if (!arg || !RL_DESC_SUPPORTED(crl_desc, pull_down) ||
+ !RL_DESC_SUPPORTED(crl_desc, pull_up))
+ return -EOPNOTSUPP;
+
+ mask |= RL_DESC_GENMASK(crl_desc, pull_down) |
+ RL_DESC_GENMASK(crl_desc, pull_up);
+ value &= ~(RL_DESC_GENMASK(crl_desc, pull_down) |
+ RL_DESC_GENMASK(crl_desc, pull_up));
+ value |= RL_DESC_GENMASK(crl_desc, pull_down);
+ break;
+ case PIN_CONFIG_BIAS_PULL_UP:
+ if (!arg || !RL_DESC_SUPPORTED(crl_desc, pull_down) ||
+ !RL_DESC_SUPPORTED(crl_desc, pull_up) ||
+ !RL_DESC_SUPPORTED(crl_desc, open_drain_pull_up_sel))
+ return -EOPNOTSUPP;
+
+ if (RL_DESC_SUPPORTED(crl_desc, pull_up)) {
+ mask |= RL_DESC_GENMASK(crl_desc, pull_down) |
+ RL_DESC_GENMASK(crl_desc, pull_up);
+ value &= ~(RL_DESC_GENMASK(crl_desc, pull_down) |
+ RL_DESC_GENMASK(crl_desc, pull_up));
+ value |= RL_DESC_GENMASK(crl_desc, pull_up);
+ } else if (RL_DESC_SUPPORTED(crl_desc, open_drain_pull_up_sel)) {
+ mask |= RL_DESC_GENMASK(crl_desc, open_drain_pull_up_sel);
+ value &= ~RL_DESC_GENMASK(crl_desc, open_drain_pull_up_sel);
+ switch (arg) {
+ case 600:
+ value |= JHB100_I2C_OPEN_DRAIN_PU_600_OHMS <<
+ RL_DESC_SHIFT(crl_desc, open_drain_pull_up_sel);
+ break;
+ case 900:
+ value |= JHB100_I2C_OPEN_DRAIN_PU_900_OHMS <<
+ RL_DESC_SHIFT(crl_desc, open_drain_pull_up_sel);
+ break;
+ case 1200:
+ value |= JHB100_I2C_OPEN_DRAIN_PU_1200_OHMS <<
+ RL_DESC_SHIFT(crl_desc, open_drain_pull_up_sel);
+ break;
+ case 2000:
+ value |= JHB100_I2C_OPEN_DRAIN_PU_2000_OHMS <<
+ RL_DESC_SHIFT(crl_desc, open_drain_pull_up_sel);
+ break;
+ default:
+ return -EOPNOTSUPP;
+ }
+ } else {
+ return -EOPNOTSUPP;
+ }
+
+ break;
+ case PIN_CONFIG_DRIVE_STRENGTH:
+ if (RL_DESC_SUPPORTED(crl_desc, drive_strength_2bit)) {
+ mask |= RL_DESC_GENMASK(crl_desc, drive_strength_2bit);
+ value &= ~RL_DESC_GENMASK(crl_desc, drive_strength_2bit);
+ value |= jhb100_padcfg_ds_from_mA(arg) <<
+ RL_DESC_SHIFT(crl_desc, drive_strength_2bit);
+ } else if (RL_DESC_SUPPORTED(crl_desc, drive_strength_3bit)) {
+ mask |= RL_DESC_GENMASK(crl_desc, drive_strength_3bit);
+ value &= ~RL_DESC_GENMASK(crl_desc, drive_strength_3bit);
+ value |= jhb100_padcfg_ds_from_mA_3bit(arg) <<
+ RL_DESC_SHIFT(crl_desc, drive_strength_3bit);
+ } else {
+ return -EOPNOTSUPP;
+ }
+ break;
+ case PIN_CONFIG_DRIVE_STRENGTH_UA:
+ if (RL_DESC_SUPPORTED(crl_desc, drive_strength_2bit)) {
+ mask |= RL_DESC_GENMASK(crl_desc, drive_strength_2bit);
+ value &= ~RL_DESC_GENMASK(crl_desc, drive_strength_2bit);
+ value |= jhb100_padcfg_ds_from_uA(arg) <<
+ RL_DESC_SHIFT(crl_desc, drive_strength_2bit);
+ } else if (RL_DESC_SUPPORTED(crl_desc, drive_strength_3bit)) {
+ mask |= RL_DESC_GENMASK(crl_desc, drive_strength_3bit);
+ value &= ~RL_DESC_GENMASK(crl_desc, drive_strength_3bit);
+ value |= jhb100_padcfg_ds_from_uA_3bit(arg) <<
+ RL_DESC_SHIFT(crl_desc, drive_strength_3bit);
+ } else {
+ return -EOPNOTSUPP;
+ }
+ break;
+ case PIN_CONFIG_INPUT_ENABLE:
+ if (!RL_DESC_SUPPORTED(crl_desc, input_enable))
+ return -EOPNOTSUPP;
+
+ mask |= RL_DESC_GENMASK(crl_desc, input_enable);
+ value = arg ? (value | RL_DESC_GENMASK(crl_desc, input_enable))
+ : value;
+ break;
+ case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
+ if (!RL_DESC_SUPPORTED(crl_desc, schmitt_trigger_select))
+ return -EOPNOTSUPP;
+
+ mask |= RL_DESC_GENMASK(crl_desc, schmitt_trigger_select);
+ value = arg
+ ? (value | RL_DESC_GENMASK(crl_desc, schmitt_trigger_select))
+ : value;
+ break;
+ case PIN_CONFIG_SLEW_RATE:
+ if (RL_DESC_SUPPORTED(crl_desc, slew_rate)) {
+ mask |= RL_DESC_GENMASK(crl_desc, slew_rate);
+ value = arg ?
+ (value | RL_DESC_GENMASK(crl_desc, slew_rate)) :
+ value;
+ } else if (RL_DESC_SUPPORTED(crl_desc, mode_select)) {
+ mask |= RL_DESC_GENMASK(crl_desc, mode_select);
+ value &= ~RL_DESC_GENMASK(crl_desc, mode_select);
+ value |= arg ?
+ JHB100_LEGACY_FAST_MODE_PLUS <<
+ RL_DESC_SHIFT(crl_desc, mode_select) :
+ JHB100_LEGACY_FAST_MODE <<
+ RL_DESC_SHIFT(crl_desc, mode_select);
+ } else {
+ return -EOPNOTSUPP;
+ }
+
+ break;
+ case PIN_CONFIG_DRIVE_PUSH_PULL:
+ if (!RL_DESC_SUPPORTED(crl_desc, mode_select))
+ return -EOPNOTSUPP;
+
+ mask |= RL_DESC_GENMASK(crl_desc, mode_select);
+ value &= ~RL_DESC_GENMASK(crl_desc, mode_select);
+ value |= JHB100_PUSH_PULL <<
+ RL_DESC_SHIFT(crl_desc, mode_select);
+ break;
+ case PIN_CONFIG_DRIVE_OPEN_DRAIN:
+ if (!RL_DESC_SUPPORTED(crl_desc, mode_select))
+ return -EOPNOTSUPP;
+
+ mask |= RL_DESC_GENMASK(crl_desc, mode_select);
+ value &= ~RL_DESC_GENMASK(crl_desc, mode_select);
+ value |= JHB100_OPEN_DRAIN <<
+ RL_DESC_SHIFT(crl_desc, mode_select);
+ break;
+ case PIN_CONFIG_INPUT_DEBOUNCE_NS:
+ u32 debounce_stage;
+
+ if (!RL_DESC_SUPPORTED(crl_desc, debounce_width))
+ return -EOPNOTSUPP;
+
+ mask |= RL_DESC_GENMASK(crl_desc, debounce_width);
+ value &= ~RL_DESC_GENMASK(crl_desc, debounce_width);
+
+ debounce_stage = arg ? arg / JHB100_DEBOUNCE_WIDTH_STAGE_NS : 0;
+ debounce_stage = umin(debounce_stage, JHB100_DEBOUNCE_WIDTH_STAGES_MAX);
+
+ value |= (debounce_stage << RL_DESC_SHIFT(crl_desc, debounce_width));
+
+ break;
+ case PIN_CONFIG_POWER_SOURCE:
+ if (&sfp->info->regs->vref) {
+ return jhb100_pincfg_group_vref(group, sfp, arg);
+ } else if (RL_DESC_SUPPORTED(crl_desc, vsel)) {
+ mask |= RL_DESC_GENMASK(crl_desc, vsel);
+ value &= ~RL_DESC_GENMASK(crl_desc, vsel);
+ value = arg ?
+ (value | (arg << RL_DESC_SHIFT(crl_desc, vsel))) :
+ value;
+ } else {
+ return -EOPNOTSUPP;
+ }
+ break;
+ default:
+ return -ENOTSUPP;
+ }
+ }
+
+ for (i = 0; i < group->grp.npins; i++)
+ jhb100_padcfg_rmw(sfp, group->grp.pins[i], mask, value);
+
+ return 0;
+}
+
+static const struct pinconf_ops jhb100_pinconf_ops = {
+ .pin_config_get = jhb100_pinconf_get,
+ .pin_config_set = jhb100_pinconf_set,
+ .pin_config_group_get = jhb100_pinconf_group_get,
+ .pin_config_group_set = jhb100_pinconf_group_set,
+ .is_generic = true,
+};
+
+static int jhb100_gpio_get_direction(struct gpio_chip *gc,
+ unsigned int gpio)
+{
+ struct jhb100_gpio_bank *bank = jhb100_gc_to_bank(gc);
+ struct jhb100_pinctrl *sfp = gpiochip_get_data(gc);
+ const struct jhb100_pinctrl_domain_info *info = sfp->info;
+ unsigned int offset = 4 * bank->id;
+ u32 doen;
+ void __iomem *reg_gpio_oen;
+
+ reg_gpio_oen = sfp->base + info->regs->output_en + offset;
+
+ doen = (readl_relaxed(reg_gpio_oen) & BIT(gpio)) >> gpio;
+
+ return doen == GPOEN_ENABLE ? GPIO_LINE_DIRECTION_OUT : GPIO_LINE_DIRECTION_IN;
+}
+
+static int jhb100_gpio_direction_input(struct gpio_chip *gc,
+ unsigned int gpio)
+{
+ struct jhb100_pinctrl *sfp = gpiochip_get_data(gc);
+ struct device *dev = sfp->dev;
+ struct config_reg_layout_desc *crl_desc;
+ unsigned int pin = jhb100_gpio_to_pin(gc, gpio);
+
+ crl_desc = get_crl_desc_by_pin(sfp, pin);
+ if (!crl_desc) {
+ dev_err(dev, "pin %d can't not found reg layout descriptor\n",
+ pin);
+ return -EINVAL;
+ }
+
+ jhb100_padcfg_rmw(sfp, pin,
+ RL_DESC_GENMASK(crl_desc, input_enable) |
+ RL_DESC_GENMASK(crl_desc, schmitt_trigger_select),
+ RL_DESC_GENMASK(crl_desc, input_enable) |
+ RL_DESC_GENMASK(crl_desc, schmitt_trigger_select));
+
+ jhb100_set_one_pin_mux(sfp, pin, 0, -1);
+
+ return 0;
+}
+
+static int jhb100_gpio_direction_output(struct gpio_chip *gc,
+ unsigned int gpio, int value)
+{
+ struct jhb100_pinctrl *sfp = gpiochip_get_data(gc);
+ struct device *dev = sfp->dev;
+ struct config_reg_layout_desc *crl_desc;
+ unsigned int pin = jhb100_gpio_to_pin(gc, gpio);
+
+ jhb100_set_one_pin_mux(sfp, pin, 0,
+ value ? GPOUT_HIGH : GPOUT_LOW);
+
+ crl_desc = get_crl_desc_by_pin(sfp, pin);
+ if (!crl_desc) {
+ dev_err(dev, "pin %d can't not found reg layout descriptor\n",
+ pin);
+ return -EINVAL;
+ }
+
+ jhb100_padcfg_rmw(sfp, pin,
+ RL_DESC_GENMASK(crl_desc, input_enable) |
+ RL_DESC_GENMASK(crl_desc, schmitt_trigger_select) |
+ RL_DESC_GENMASK(crl_desc, pull_down) |
+ RL_DESC_GENMASK(crl_desc, pull_up),
+ 0);
+
+ return 0;
+}
+
+static int jhb100_gpio_get(struct gpio_chip *gc, unsigned int gpio)
+{
+ struct jhb100_gpio_bank *bank = jhb100_gc_to_bank(gc);
+ struct jhb100_pinctrl *sfp = gpiochip_get_data(gc);
+ const struct jhb100_pinctrl_domain_info *info = sfp->info;
+ unsigned int offset = 4 * bank->id;
+ u32 doen = 0;
+ void __iomem *reg_gpio_oen;
+ void __iomem *reg;
+ unsigned long flags;
+
+ reg_gpio_oen = sfp->base + info->regs->output_en + offset;
+ reg = sfp->base + info->regs->gpio_status + offset;
+
+ raw_spin_lock_irqsave(&sfp->lock, flags);
+ doen = readl_relaxed(reg_gpio_oen) | BIT(gpio);
+ writel_relaxed(doen, reg_gpio_oen);
+ raw_spin_unlock_irqrestore(&sfp->lock, flags);
+
+ return !!(readl_relaxed(reg) & BIT(gpio % 32));
+}
+
+static int jhb100_gpio_set(struct gpio_chip *gc, unsigned int gpio, int value)
+{
+ struct jhb100_gpio_bank *bank = jhb100_gc_to_bank(gc);
+ struct jhb100_pinctrl *sfp = gpiochip_get_data(gc);
+ const struct jhb100_pinctrl_domain_info *info = sfp->info;
+ unsigned int offset = 4 * bank->id;
+ void __iomem *reg_dout;
+ u32 dout;
+ unsigned long flags;
+
+ reg_dout = sfp->base + info->regs->output + offset;
+ dout = (value ? GPOUT_HIGH : GPOUT_LOW) << gpio;
+
+ raw_spin_lock_irqsave(&sfp->lock, flags);
+ dout |= readl_relaxed(reg_dout) & ~BIT(gpio);
+ writel_relaxed(dout, reg_dout);
+ raw_spin_unlock_irqrestore(&sfp->lock, flags);
+
+ return 0;
+}
+
+static void jhb100_irq_ack(struct irq_data *d)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+ struct jhb100_gpio_bank *bank = jhb100_gc_to_bank(gc);
+ struct jhb100_pinctrl *sfp = gpiochip_get_data(gc);
+ struct starfive_pinctrl_regs *pinctrl_regs = sfp->info->regs;
+ irq_hw_number_t gpio = irqd_to_hwirq(d);
+ unsigned int offset = 4 * bank->id;
+ void __iomem *ic;
+ unsigned long flags;
+ u32 value;
+ u32 mask;
+
+ ic = sfp->base + pinctrl_regs->irq_clr + offset;
+ mask = BIT(gpio);
+
+ raw_spin_lock_irqsave(&sfp->lock, flags);
+ value = readl_relaxed(ic) & ~mask;
+ writel_relaxed(value | mask, ic);
+ value = readl_relaxed(ic) & ~mask;
+ writel_relaxed(value, ic);
+ raw_spin_unlock_irqrestore(&sfp->lock, flags);
+}
+
+static void jhb100_irq_mask(struct irq_data *d)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+ struct jhb100_gpio_bank *bank = jhb100_gc_to_bank(gc);
+ struct jhb100_pinctrl *sfp = gpiochip_get_data(gc);
+ struct starfive_pinctrl_regs *pinctrl_regs = sfp->info->regs;
+ irq_hw_number_t gpio = irqd_to_hwirq(d);
+ unsigned int offset = 4 * bank->id;
+ void __iomem *ien;
+ unsigned long flags;
+ u32 value;
+ u32 mask;
+
+ ien = sfp->base + pinctrl_regs->irq_en + offset;
+ mask = BIT(gpio);
+
+ raw_spin_lock_irqsave(&sfp->lock, flags);
+ value = readl_relaxed(ien) & ~mask;
+ writel_relaxed(value, ien);
+ raw_spin_unlock_irqrestore(&sfp->lock, flags);
+
+ gpiochip_disable_irq(gc, d->hwirq);
+}
+
+static void jhb100_irq_mask_ack(struct irq_data *d)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+ struct jhb100_gpio_bank *bank = jhb100_gc_to_bank(gc);
+ struct jhb100_pinctrl *sfp = gpiochip_get_data(gc);
+ struct starfive_pinctrl_regs *pinctrl_regs = sfp->info->regs;
+ irq_hw_number_t gpio = irqd_to_hwirq(d);
+ unsigned int offset = 4 * bank->id;
+ void __iomem *ien;
+ void __iomem *ic;
+ unsigned long flags;
+ u32 value;
+ u32 mask;
+
+ ien = sfp->base + pinctrl_regs->irq_en + offset;
+ ic = sfp->base + pinctrl_regs->irq_clr + offset;
+ mask = BIT(gpio);
+
+ raw_spin_lock_irqsave(&sfp->lock, flags);
+ value = readl_relaxed(ien) & ~mask;
+ writel_relaxed(value, ien);
+
+ value = readl_relaxed(ic) & ~mask;
+ writel_relaxed(value | mask, ic);
+ value = readl_relaxed(ic) & ~mask;
+ writel_relaxed(value, ic);
+ raw_spin_unlock_irqrestore(&sfp->lock, flags);
+}
+
+static void jhb100_irq_unmask(struct irq_data *d)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+ struct jhb100_gpio_bank *bank = jhb100_gc_to_bank(gc);
+ struct jhb100_pinctrl *sfp = gpiochip_get_data(gc);
+ struct starfive_pinctrl_regs *pinctrl_regs = sfp->info->regs;
+ irq_hw_number_t gpio = irqd_to_hwirq(d);
+ unsigned int offset = 4 * bank->id;
+ void __iomem *ien;
+ unsigned long flags;
+ u32 value;
+ u32 mask;
+
+ ien = sfp->base + pinctrl_regs->irq_en + offset;
+ mask = BIT(gpio);
+
+ gpiochip_enable_irq(gc, d->hwirq);
+
+ raw_spin_lock_irqsave(&sfp->lock, flags);
+ value = readl_relaxed(ien) | mask;
+ writel_relaxed(value, ien);
+ raw_spin_unlock_irqrestore(&sfp->lock, flags);
+}
+
+static int jhb100_irq_set_type(struct irq_data *d, unsigned int trigger)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+ struct jhb100_gpio_bank *bank = jhb100_gc_to_bank(gc);
+ struct jhb100_pinctrl *sfp = gpiochip_get_data(gc);
+ struct starfive_pinctrl_regs *pinctrl_regs = sfp->info->regs;
+ irq_hw_number_t gpio = irqd_to_hwirq(d);
+ unsigned int offset = 4 * bank->id;
+ void __iomem *base;
+ u32 irq_type, edge_both, polarity, mask;
+ unsigned long flags;
+
+ base = sfp->base + offset;
+ mask = BIT(gpio);
+
+ switch (trigger) {
+ case IRQ_TYPE_EDGE_RISING:
+ irq_type = mask; /* 1: edge triggered */
+ edge_both = 0; /* 0: single edge */
+ polarity = mask; /* 1: rising edge */
+ break;
+ case IRQ_TYPE_EDGE_FALLING:
+ irq_type = mask; /* 1: edge triggered */
+ edge_both = 0; /* 0: single edge */
+ polarity = 0; /* 0: falling edge */
+ break;
+ case IRQ_TYPE_EDGE_BOTH:
+ irq_type = mask; /* 1: edge triggered */
+ edge_both = mask; /* 1: both edges */
+ polarity = 0; /* 0: ignored */
+ break;
+ case IRQ_TYPE_LEVEL_HIGH:
+ irq_type = 0; /* 0: level triggered */
+ edge_both = 0; /* 0: ignored */
+ polarity = mask; /* 1: high level */
+ break;
+ case IRQ_TYPE_LEVEL_LOW:
+ irq_type = 0; /* 0: level triggered */
+ edge_both = 0; /* 0: ignored */
+ polarity = 0; /* 0: low level */
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ if (trigger & IRQ_TYPE_EDGE_BOTH)
+ irq_set_handler_locked(d, handle_edge_irq);
+ else
+ irq_set_handler_locked(d, handle_level_irq);
+
+ raw_spin_lock_irqsave(&sfp->lock, flags);
+ irq_type |= readl_relaxed(base + pinctrl_regs->irq_trigger) & ~mask;
+ writel_relaxed(irq_type, base + pinctrl_regs->irq_trigger);
+
+ edge_both |= readl_relaxed(base + pinctrl_regs->irq_both_edge) & ~mask;
+ writel_relaxed(edge_both, base + pinctrl_regs->irq_both_edge);
+
+ if (irq_type & mask) { /* edge polarity */
+ polarity |= readl_relaxed(base + pinctrl_regs->irq_edge) & ~mask;
+ writel_relaxed(polarity, base + pinctrl_regs->irq_edge);
+ } else if (irq_type == 0) { /* level polarity */
+ polarity |= readl_relaxed(base + pinctrl_regs->irq_level) & ~mask;
+ writel_relaxed(polarity, base + pinctrl_regs->irq_level);
+ }
+ raw_spin_unlock_irqrestore(&sfp->lock, flags);
+ return 0;
+}
+
+static int jhb100_irq_set_wake(struct irq_data *d, unsigned int enable)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+ struct jhb100_pinctrl *sfp = gpiochip_get_data(gc);
+ int ret = 0;
+
+ if (enable)
+ ret = enable_irq_wake(sfp->wakeup_irq);
+ else
+ ret = disable_irq_wake(sfp->wakeup_irq);
+ if (ret)
+ dev_err(sfp->dev, "failed to %s wake-up interrupt\n",
+ enable ? "enable" : "disable");
+
+ return ret;
+}
+
+static void jhb100_irq_print_chip(struct irq_data *d, struct seq_file *p)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+ struct jhb100_gpio_bank *bank = jhb100_gc_to_bank(gc);
+
+ seq_printf(p, "%s-%d", gc->label, bank->id);
+}
+
+static const struct irq_chip jhb100_irq_chip = {
+ .irq_ack = jhb100_irq_ack,
+ .irq_mask = jhb100_irq_mask,
+ .irq_mask_ack = jhb100_irq_mask_ack,
+ .irq_unmask = jhb100_irq_unmask,
+ .irq_set_type = jhb100_irq_set_type,
+ .irq_set_wake = jhb100_irq_set_wake,
+ .irq_print_chip = jhb100_irq_print_chip,
+ .flags = IRQCHIP_SET_TYPE_MASKED |
+ IRQCHIP_IMMUTABLE |
+ IRQCHIP_ENABLE_WAKEUP_ON_SUSPEND |
+ IRQCHIP_MASK_ON_SUSPEND |
+ IRQCHIP_SKIP_SET_WAKE,
+ GPIOCHIP_IRQ_RESOURCE_HELPERS,
+};
+
+static irqreturn_t jhb100_gpio_irq_handler(int irq, void *dev_id)
+{
+ struct jhb100_gpio_bank *bank = dev_id;
+ struct gpio_chip *gc = &bank->gc;
+ struct jhb100_pinctrl *sfp = gpiochip_get_data(gc);
+ struct gpio_irq_chip *girq = &gc->irq;
+ struct starfive_pinctrl_regs *pinctrl_regs = sfp->info->regs;
+ unsigned int irq_status = pinctrl_regs->irq_status + bank->id * 4;
+ unsigned long is;
+ unsigned int gpio;
+
+ is = readl_relaxed(sfp->base + irq_status);
+ if (!is)
+ return IRQ_NONE;
+
+ for_each_set_bit(gpio, &is, gc->ngpio)
+ generic_handle_domain_irq(girq->domain, gpio);
+
+ return IRQ_HANDLED;
+}
+
+static int field_compare(const void *a, const void *b)
+{
+ const struct field_info *fa = (const struct field_info *)a;
+ const struct field_info *fb = (const struct field_info *)b;
+
+ if (fa->shift < fb->shift)
+ return -1;
+
+ if (fa->shift > fb->shift)
+ return 1;
+
+ return 0;
+}
+
+static int check_crl_desc(struct jhb100_pinctrl *sfp, unsigned int index,
+ const struct config_reg_layout_desc *desc)
+{
+ struct device *dev = sfp->dev;
+ struct field_info *fields;
+ int field_cnt = 0;
+ int num, i;
+
+ num = sizeof(struct config_reg_layout_desc) / sizeof(struct reg_layout_field);
+
+ fields = kcalloc(num, sizeof(struct field_info), GFP_KERNEL);
+ if (!fields)
+ return -ENOMEM;
+
+ #define COLLECT_FIELD(field) \
+ do { \
+ if (desc->field.width > 0) { \
+ fields[field_cnt].name = #field; \
+ fields[field_cnt].shift = desc->field.shift; \
+ fields[field_cnt].width = desc->field.width; \
+ fields[field_cnt].end = desc->field.shift + desc->field.width; \
+ field_cnt++; \
+ } \
+ } while (0)
+
+ /* same as struct config_reg_layout_desc filed except for pin_start and pin_cnt */
+ COLLECT_FIELD(debounce_width);
+ COLLECT_FIELD(drive_strength_2bit);
+ COLLECT_FIELD(drive_strength_3bit);
+ COLLECT_FIELD(function);
+ COLLECT_FIELD(input_enable);
+ COLLECT_FIELD(vsel);
+ COLLECT_FIELD(mode_select);
+ COLLECT_FIELD(open_drain_pull_up_sel);
+ COLLECT_FIELD(pull_down);
+ COLLECT_FIELD(pull_up);
+ COLLECT_FIELD(reserved);
+ COLLECT_FIELD(retention_signal_bus);
+ COLLECT_FIELD(schmitt_trigger_select);
+ COLLECT_FIELD(slew_rate);
+
+ #undef COLLECT_FIELD
+
+ sort(fields, field_cnt, sizeof(struct field_info), field_compare, NULL);
+
+ for (i = 0; i < field_cnt; i++) {
+ if (fields[i].end > 32) {
+ dev_err(dev,
+ "layout %d: field %s exceeds 32bit [shift=%u, width=%u, end=%u]\n",
+ index, fields[i].name,
+ fields[i].shift, fields[i].width, fields[i].end);
+ goto failed;
+ }
+
+ if (i < field_cnt - 1) {
+ if (fields[i].end > fields[i + 1].shift) {
+ dev_err(dev,
+ "layout %d: field overlap: %s[%u:%u] with %s[%u:%u]\n",
+ index, fields[i].name, fields[i].end - 1,
+ fields[i].shift, fields[i + 1].name,
+ fields[i + 1].end - 1, fields[i + 1].shift);
+ goto failed;
+ }
+ }
+ }
+
+ if (desc->reserved.width > 0) {
+ unsigned int used_mask = 0;
+ unsigned int reserved_mask = 0;
+
+ for (i = 0; i < field_cnt; i++) {
+ if (strcmp(fields[i].name, "reserved"))
+ used_mask |= GENMASK(fields[i].end - 1, fields[i].shift);
+ else
+ reserved_mask |= GENMASK(fields[i].end - 1, fields[i].shift);
+ }
+
+ if ((used_mask | reserved_mask) != 0xFFFFFFFF) {
+ dev_err(dev,
+ "layout %d: reserved field not cover all unused bits\n",
+ index);
+ dev_err(dev,
+ "used mask: 0x%08X, reserved mask: 0x%08X, combined: 0x%08X\n",
+ used_mask, reserved_mask, used_mask | reserved_mask);
+ }
+ }
+
+ kfree(fields);
+ return 0;
+
+failed:
+ kfree(fields);
+ return -EINVAL;
+}
+
+static int check_layout_pin_range(struct jhb100_pinctrl *sfp,
+ const struct config_reg_layout_desc *descs,
+ unsigned int num_desc)
+{
+ struct device *dev = sfp->dev;
+
+ if (descs[num_desc - 1].pin_start + descs[num_desc - 1].pin_cnt > sfp->npins) {
+ dev_err(dev, "layout %u pin_start[%u] + pin_cnt[%u] exceeds pin number[%u]\n",
+ num_desc - 1, descs[num_desc - 1].pin_start,
+ descs[num_desc - 1].pin_cnt, sfp->npins);
+ return -EINVAL;
+ }
+
+ for (int i = 0; i < num_desc; i++) {
+ if (descs[i].pin_start == 0xff)
+ break;
+
+ if (i < num_desc - 1) {
+ if (descs[i].pin_start + descs[i].pin_cnt > descs[i + 1].pin_start) {
+ dev_err(dev, "pin range: [%u-%u] overlaps with [%u-%u]\n",
+ descs[i].pin_start, descs[i].pin_cnt,
+ descs[i + 1].pin_start, descs[i + 1].pin_cnt);
+ return -EINVAL;
+ }
+
+ if (descs[i].pin_start + descs[i].pin_cnt < descs[i + 1].pin_start) {
+ dev_err(dev, "pin range: [%u-%u] -> [%u-%u] has gap\n",
+ descs[i].pin_start, descs[i].pin_cnt,
+ descs[i + 1].pin_start, descs[i + 1].pin_cnt);
+ return -EINVAL;
+ }
+ }
+ }
+
+ return 0;
+}
+
+static int check_pinctrl_layouts(struct jhb100_pinctrl *sfp,
+ const struct config_reg_layout_desc *layouts)
+{
+ struct device *dev = sfp->dev;
+ int i = 0, err_cnt = 0, ret;
+
+ if (!layouts) {
+ dev_err(dev, "layout pointer is NULL\n");
+ return -EINVAL;
+ }
+
+ while (layouts[i].pin_start != 0xff) {
+ ret = check_crl_desc(sfp, i, &layouts[i]);
+ if (ret) {
+ dev_err(dev, "layout %d check failed\n", i);
+ err_cnt++;
+ }
+
+ if (++i > 100) {
+ dev_err(dev, "too many layouts or missing 0xff for end\n");
+ return -EINVAL;
+ }
+ }
+
+ if (!err_cnt) {
+ ret = check_layout_pin_range(sfp, layouts, i);
+ if (ret)
+ err_cnt++;
+ }
+
+ if (err_cnt) {
+ dev_err(dev, "pinctrl layout check finish with %d error(s)\n", err_cnt);
+ return -EINVAL;
+ }
+
+ dev_info(dev, "pinctrl layout check completed!\n");
+ return 0;
+}
+
+static
+struct pinctrl_pin_desc *devm_create_pins_from_pld(struct device *dev,
+ const struct jhb100_pin_layout_desc *desc,
+ const char *prefix,
+ unsigned int *total_pins,
+ unsigned int *total_gpios,
+ s8 **gpio_func_sel_arr)
+{
+ struct pinctrl_pin_desc *pins = NULL;
+ unsigned int i, j, ngpios = 0, npins = 0, pin_index = 0;
+ unsigned int same_name_found = 0;
+ s8 *arr;
+
+ if (!dev || !desc || !prefix) {
+ dev_err(dev, "Invalid parameters: desc=%p, prefix=%s\n",
+ desc, prefix);
+ return ERR_PTR(-EINVAL);
+ }
+
+ for (i = 0; desc[i].pin_start != 0xff; i++) {
+ if (!desc[i].pin_cnt) {
+ dev_err(dev, "Invalid pin cnt\n");
+ return ERR_PTR(-EINVAL);
+ }
+
+ npins += desc[i].pin_cnt;
+ }
+
+ if (npins == 0) {
+ dev_err(dev, "No pins defined\n");
+ return ERR_PTR(-EINVAL);
+ }
+
+ dev_dbg(dev, "Total pins to create: %d\n", npins);
+
+ pins = devm_kcalloc(dev, npins, sizeof(*pins), GFP_KERNEL);
+ if (!pins)
+ return ERR_PTR(-ENOMEM);
+
+ arr = devm_kzalloc(dev, npins, GFP_KERNEL);
+ if (!arr)
+ return ERR_PTR(-ENOMEM);
+
+ for (i = 0; desc[i].pin_start != 0xff; i++) {
+ same_name_found = 0;
+
+ for (j = 0; j < i; j++) {
+ if (!strcmp(desc[j].name, desc[i].name)) {
+ same_name_found = 1;
+ break;
+ }
+ }
+
+ for (j = 0; j < desc[i].pin_cnt; j++) {
+ char *name = NULL;
+ int pin_num = desc[i].pin_start + j;
+
+ pins[pin_index].number = pin_num;
+ if (same_name_found) {
+ name = devm_kasprintf(dev, GFP_KERNEL, "%s_%s_%d",
+ prefix, desc[i].name,
+ desc[i].pin_start + j);
+ } else {
+ if (desc[i].pin_cnt > 1)
+ name = devm_kasprintf(dev, GFP_KERNEL, "%s_%s_%d",
+ prefix, desc[i].name, j);
+ else
+ name = devm_kasprintf(dev, GFP_KERNEL, "%s_%s",
+ prefix, desc[i].name);
+ }
+
+ if (!name) {
+ dev_err(dev, "Failed to allocate pin name for pin %d\n",
+ pin_num);
+ return ERR_PTR(-ENOMEM);
+ }
+
+ if (!strcmp(desc[i].name, "gpio") || desc[i].gpio_func_sel != -1)
+ ngpios++;
+
+ pins[pin_index].name = name;
+ arr[pin_index] = desc[i].gpio_func_sel;
+ pin_index++;
+ }
+ }
+
+ *total_pins = npins;
+ *total_gpios = ngpios;
+ *gpio_func_sel_arr = arr;
+
+ return pins;
+}
+
+static bool starfive_of_node_instance_match(struct gpio_chip *gc, unsigned int i)
+{
+ struct jhb100_pinctrl *sfp = gpiochip_get_data(gc);
+
+ if (i >= sfp->num_banks)
+ return false;
+
+ return (gc == &sfp->banks[i].gc);
+}
+
+int jhb100_pinctrl_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct gpio_irq_chip *girq;
+ const struct jhb100_pinctrl_domain_info *info;
+ struct jhb100_pinctrl *sfp;
+ struct pinctrl_desc *jhb100_pinctrl_desc;
+ struct starfive_pinctrl_regs *pinctrl_regs;
+ struct reset_control *rst;
+ struct clk *clk;
+ int ret;
+ int irq;
+
+ info = of_device_get_match_data(&pdev->dev);
+ if (!info)
+ return -ENODEV;
+
+ pinctrl_regs = info->regs;
+
+ sfp = devm_kzalloc(dev, sizeof(*sfp), GFP_KERNEL);
+ if (!sfp)
+ return -ENOMEM;
+
+ sfp->base = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(sfp->base))
+ return PTR_ERR(sfp->base);
+
+ clk = devm_clk_get_optional_enabled(dev, NULL);
+ if (IS_ERR(clk))
+ return dev_err_probe(dev, PTR_ERR(clk), "could not get & enable clock\n");
+
+ rst = devm_reset_control_array_get_optional_shared(dev);
+ if (IS_ERR(rst))
+ return dev_err_probe(dev, PTR_ERR(rst), "could not get reset control\n");
+
+ /*
+ * we don't want to assert reset and risk undoing pin muxing for the
+ * early boot serial console, but let's make sure the reset line is
+ * deasserted in case someone runs a really minimal bootloader.
+ */
+ ret = reset_control_deassert(rst);
+ if (ret)
+ return dev_err_probe(dev, ret, "could not deassert reset\n");
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0)
+ return irq;
+
+ sfp->pins = devm_create_pins_from_pld(dev, info->pl_desc, info->name,
+ &sfp->npins, &sfp->ngpios,
+ &sfp->gpio_func_sel_arr);
+ if (IS_ERR(sfp->pins))
+ return PTR_ERR(sfp->pins);
+
+ jhb100_pinctrl_desc = devm_kzalloc(&pdev->dev,
+ sizeof(*jhb100_pinctrl_desc),
+ GFP_KERNEL);
+ if (!jhb100_pinctrl_desc)
+ return -ENOMEM;
+
+ jhb100_pinctrl_desc->name = dev_name(dev);
+ jhb100_pinctrl_desc->pctlops = &jhb100_pinctrl_ops;
+ jhb100_pinctrl_desc->pmxops = &jhb100_pinmux_ops;
+ jhb100_pinctrl_desc->confops = &jhb100_pinconf_ops;
+ jhb100_pinctrl_desc->owner = THIS_MODULE;
+ jhb100_pinctrl_desc->pins = sfp->pins;
+ jhb100_pinctrl_desc->npins = sfp->npins;
+
+ sfp->info = info;
+ sfp->dev = dev;
+ platform_set_drvdata(pdev, sfp);
+
+ raw_spin_lock_init(&sfp->lock);
+ mutex_init(&sfp->mutex);
+
+ ret = devm_pinctrl_register_and_init(dev, jhb100_pinctrl_desc,
+ sfp, &sfp->pctl);
+ if (ret)
+ return dev_err_probe(dev, ret,
+ "could not register pinctrl driver\n");
+
+ ret = pinctrl_enable(sfp->pctl);
+ if (ret)
+ return ret;
+
+ sfp->num_banks = DIV_ROUND_UP(sfp->ngpios, JHB100_NR_GPIOS_PER_BANK);
+
+ for (unsigned int i = 0; i < sfp->num_banks; i++) {
+ if (sfp->ngpios > (i + 1) * JHB100_NR_GPIOS_PER_BANK)
+ sfp->banks[i].gc.ngpio = (i + 1) * JHB100_NR_GPIOS_PER_BANK;
+ else
+ sfp->banks[i].gc.ngpio = sfp->ngpios - i * JHB100_NR_GPIOS_PER_BANK;
+
+ sfp->banks[i].id = i;
+
+ sfp->banks[i].gc.parent = dev;
+ sfp->banks[i].gc.label = dev_name(dev);
+ sfp->banks[i].gc.owner = THIS_MODULE;
+ sfp->banks[i].gc.request = pinctrl_gpio_request;
+ sfp->banks[i].gc.free = pinctrl_gpio_free;
+ sfp->banks[i].gc.get_direction = jhb100_gpio_get_direction;
+ sfp->banks[i].gc.direction_input = jhb100_gpio_direction_input;
+ sfp->banks[i].gc.direction_output = jhb100_gpio_direction_output;
+ sfp->banks[i].gc.get = jhb100_gpio_get;
+ sfp->banks[i].gc.set = jhb100_gpio_set;
+ sfp->banks[i].gc.set_config = gpiochip_generic_config;
+ sfp->banks[i].gc.base = -1;
+ sfp->banks[i].gc.of_gpio_n_cells = 3;
+ sfp->banks[i].gc.of_node_instance_match = starfive_of_node_instance_match;
+
+ girq = &sfp->banks[i].gc.irq;
+ girq->handler = handle_simple_irq;
+
+ gpio_irq_chip_set_chip(girq, &jhb100_irq_chip);
+
+ /* mask all GPIO interrupts */
+ writel_relaxed(0U, sfp->base + pinctrl_regs->irq_en + 4 * i);
+ /* clear all interrupts */
+ writel_relaxed(~0U, sfp->base + pinctrl_regs->irq_clr + 4 * i);
+ writel_relaxed(0U, sfp->base + pinctrl_regs->irq_clr + 4 * i);
+
+ ret = devm_request_irq(dev, irq, jhb100_gpio_irq_handler, IRQF_SHARED,
+ sfp->banks[i].gc.label, &sfp->banks[i]);
+ if (ret < 0)
+ return dev_err_probe(dev, ret, "failed to register IRQ\n");
+
+ ret = devm_gpiochip_add_data(dev, &sfp->banks[i].gc, sfp);
+ if (ret)
+ return dev_err_probe(dev, ret, "could not register gpiochip\n");
+ }
+
+ dev_info(dev, "StarFive JHB100 GPIO chip registered %d GPIOs\n",
+ sfp->ngpios);
+
+ ret = check_pinctrl_layouts(sfp, info->crl_desc);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(jhb100_pinctrl_probe);
+
+MODULE_DESCRIPTION("Pinctrl driver for the StarFive JHB100 SoC");
+MODULE_AUTHOR("Alex Soo <yuklin.soo@starfivetech.com>");
+MODULE_LICENSE("GPL");
diff --git a/drivers/pinctrl/starfive/pinctrl-starfive-jhb100.h b/drivers/pinctrl/starfive/pinctrl-starfive-jhb100.h
new file mode 100644
index 000000000000..0fc45b445c6d
--- /dev/null
+++ b/drivers/pinctrl/starfive/pinctrl-starfive-jhb100.h
@@ -0,0 +1,152 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Pinctrl / GPIO driver for StarFive JHB100 SoC
+ *
+ * Copyright (C) 2024 StarFive Technology Co., Ltd.
+ * Author: Alex Soo <yuklin.soo@starfivetech.com>
+ *
+ */
+
+#ifndef __PINCTRL_STARFIVE_JHB100_H__
+#define __PINCTRL_STARFIVE_JHB100_H__
+
+#include <linux/gpio/driver.h>
+#include <linux/pinctrl/pinconf-generic.h>
+#include <linux/pinctrl/pinmux.h>
+
+#define JHB100_MAX_BANKS 2
+
+struct jhb100_pin_layout_desc {
+ unsigned int pin_start;
+ unsigned int pin_cnt;
+ const char *name;
+ s8 gpio_func_sel;
+};
+
+struct jhb100_gpio_bank {
+ struct gpio_chip gc;
+ unsigned int id;
+};
+
+struct jhb100_pinctrl {
+ struct device *dev;
+ struct jhb100_gpio_bank banks[JHB100_MAX_BANKS];
+ unsigned int num_banks;
+ struct pinctrl_gpio_range gpios;
+ raw_spinlock_t lock;
+ const char *iodomain_name;
+ void __iomem *base;
+ struct pinctrl_dev *pctl;
+ /* register read/write mutex */
+ struct mutex mutex;
+ const struct jhb100_pinctrl_domain_info *info;
+ /* wakeup */
+ int wakeup_irq;
+ struct irq_domain *irq_domain;
+ const struct pinctrl_pin_desc *pins;
+ unsigned int npins;
+ unsigned int ngpios;
+ s8 *gpio_func_sel_arr;
+};
+
+struct pinvref_desc {
+ const char *name;
+ unsigned int range;
+ u32 pin_grp[32];
+ u32 num_pins;
+};
+
+struct pinvref_reg {
+ unsigned int reg;
+ const struct pinvref_desc *pv_desc;
+};
+
+struct gpio_irq_reg {
+ unsigned int reg;
+ unsigned int width_per_pin;
+};
+
+struct starfive_pinctrl_regs {
+ struct pinvref_reg vref;
+ struct gpio_irq_reg func_sel;
+ unsigned int config;
+ unsigned int output;
+ unsigned int output_en;
+ unsigned int gpio_status;
+ unsigned int irq_en;
+ unsigned int irq_status;
+ unsigned int irq_clr;
+ unsigned int irq_trigger;
+ unsigned int irq_level;
+ unsigned int irq_both_edge;
+ unsigned int irq_edge;
+};
+
+struct reg_layout_field {
+ unsigned char shift;
+ unsigned char width;
+};
+
+#define RL_DESC_SUPPORTED(crl_desc, field) ({ \
+ typeof(crl_desc) _desc = (crl_desc); \
+ (_desc && _desc->field.width > 0); \
+})
+
+#define RL_DESC_SHIFT(crl_desc, field) ({ \
+ typeof(crl_desc) __desc = (crl_desc); \
+ __desc->field.shift; \
+})
+
+#define RL_DESC_GENMASK(crl_desc, field) ({ \
+ typeof(crl_desc) __desc = (crl_desc); \
+ RL_DESC_SUPPORTED(__desc, field) ? \
+ GENMASK(__desc->field.shift + __desc->field.width - 1, __desc->field.shift) : 0; \
+})
+
+struct config_reg_layout_desc {
+ unsigned int pin_start;
+ unsigned int pin_cnt;
+
+ struct reg_layout_field debounce_width;
+ struct reg_layout_field drive_strength_2bit;
+ struct reg_layout_field drive_strength_3bit;
+ struct reg_layout_field function;
+ struct reg_layout_field input_enable;
+ struct reg_layout_field vsel;
+ struct reg_layout_field mode_select;
+ struct reg_layout_field open_drain_pull_up_sel;
+ struct reg_layout_field pull_down;
+ struct reg_layout_field pull_up;
+ struct reg_layout_field reserved;
+ struct reg_layout_field retention_signal_bus;
+ struct reg_layout_field schmitt_trigger_select;
+ struct reg_layout_field slew_rate;
+};
+
+struct funcsel_reg_layout_desc {
+ unsigned int pin_start;
+ unsigned int pin_cnt;
+ unsigned int width;
+};
+
+#define JHB100_FUNC_MAPS_MAX_PIN(n) ((n) + 1)
+
+struct jhb100_pinctrl_func_maps {
+ char *func;
+ unsigned char val;
+ u32 max_pin;
+};
+
+struct jhb100_pinctrl_domain_info {
+ const char *name;
+ const struct pinctrl_pin_desc *pins;
+ const struct jhb100_pin_layout_desc *pl_desc;
+ const struct jhb100_pinctrl_func_maps *fmaps;
+ u32 num_maps;
+ struct config_reg_layout_desc *crl_desc;
+ struct starfive_pinctrl_regs *regs;
+};
+
+int jhb100_pinctrl_probe(struct platform_device *pdev);
+
+#endif /* __PINCTRL_STARFIVE_JHB100_H__ */
--
2.25.1
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply related [flat|nested] 32+ messages in thread* [PATCH v2 06/22] dt-bindings: pinctrl: Add starfive,jhb100-sys0h-pinctrl
2026-05-14 11:11 [PATCH v2 00/22] Add basic pinctrl drivers for JHB100 SoC Changhuang Liang
` (4 preceding siblings ...)
2026-05-14 11:12 ` [PATCH v2 05/22] pinctrl: starfive: Add StarFive JHB100 sys0 controller driver Changhuang Liang
@ 2026-05-14 11:12 ` Changhuang Liang
2026-05-14 13:17 ` Rob Herring (Arm)
2026-05-14 11:12 ` [PATCH v2 07/22] pinctrl: starfive: Add StarFive JHB100 sys0h controller driver Changhuang Liang
` (15 subsequent siblings)
21 siblings, 1 reply; 32+ messages in thread
From: Changhuang Liang @ 2026-05-14 11:12 UTC (permalink / raw)
To: Linus Walleij, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Emil Renner Berthing, Paul Walmsley, Albert Ou, Palmer Dabbelt,
Alexandre Ghiti, Philipp Zabel, Bartosz Golaszewski
Cc: linux-gpio, linux-kernel, devicetree, linux-riscv,
Lianfeng Ouyang, Changhuang Liang
Add pinctrl bindings for StarFive JHB100 SoC System-0 host(sys0h) pinctrl
controller.
Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
---
.../starfive,jhb100-sys0h-pinctrl.yaml | 174 ++++++++++++++++++
.../pinctrl/starfive,jhb100-pinctrl.h | 14 ++
2 files changed, 188 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys0h-pinctrl.yaml
diff --git a/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys0h-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys0h-pinctrl.yaml
new file mode 100644
index 000000000000..cace3fdd00ec
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys0h-pinctrl.yaml
@@ -0,0 +1,174 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/starfive,jhb100-sys0h-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: StarFive JHB100 System-0 Host Pin Controller
+
+description: |
+ Pinctrl bindings for JHB100 RISC-V SoC from StarFive Technology Ltd.
+
+ The JHB100 SoC has 13 pinctrl domains - sys0, sys0h, sys1, sys2, per0, per1,
+ per2, per2pok, per3, adc0, adc1, emmc, and vga.
+ This document provides an overview of the "sys0h" pinctrl domain.
+
+ The "sys0h" domain has a pin controller which provides
+ - function selection for GPIO pads.
+ - GPIO pad configuration.
+ - GPIO interrupt handling.
+
+ In the SYS0H Pin Controller, there are 12 multi-function GPIO_PADs. Each of
+ them can be multiplexed to different hardware blocks through function
+ selection. Each iopad has a maximum of up to 3 functions - 0, 1, 2, and 3.
+ Function 0 is the default function which is generally the GPIO function
+ (or occasionally, it can be a peripheral signal).
+ Functions 1, 2, and 3 are the alternate functions or peripheral signals that
+ can be routed to the iopad. The function selection can be carried out by
+ writing the function number to the iopad function select register.
+
+ Each iopad is configurable with parameters such as input-enable, internal
+ pull-up/pull-down bias, drive strength, schmitt trigger, slew rate, input
+ debounce nanoseconds, power source and drive type (open-drain or push-pull).
+
+maintainers:
+ - Alex Soo <yuklin.soo@starfivetech.com>
+
+properties:
+ compatible:
+ items:
+ - const: starfive,jhb100-sys0h-pinctrl
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ resets:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ interrupt-controller: true
+
+ '#interrupt-cells':
+ const: 3
+
+ gpio-controller: true
+
+ '#gpio-cells':
+ const: 3
+
+ gpio-ranges: true
+
+ gpio-line-names: true
+
+patternProperties:
+ '-grp$':
+ type: object
+ additionalProperties: false
+ patternProperties:
+ '-pins$':
+ type: object
+ description: |
+ A pinctrl node should contain at least one subnode representing the
+ pinctrl groups available in the domain. Each subnode will list the
+ pins it needs, and how they should be configured, with regard to
+ function selection, bias, input enable/disable, input schmitt
+ trigger enable/disable, slew-rate, input debounce nanoseconds,
+ drive-open-drain, drive-push-pull, power-source and drive-strength.
+ allOf:
+ - $ref: /schemas/pinctrl/pincfg-node.yaml
+ - $ref: /schemas/pinctrl/pinmux-node.yaml
+ unevaluatedProperties: false
+
+ properties:
+ pins:
+ description:
+ The list of IOs that properties in the pincfg node apply to.
+
+ function:
+ description:
+ A string containing the name of the function to mux for these
+ pins.
+ enum: [ espi, espi_reset, espi0_vw, espi0_vw1, gpio, scap_trigger ]
+
+ bias-disable: true
+
+ bias-pull-down:
+ type: boolean
+
+ bias-pull-up:
+ oneOf:
+ - type: boolean
+ - enum: [ 600, 900, 1200, 2000 ]
+ description: Pull up RSEL type resistance values (in ohms)
+ description:
+ For normal pull up type there is no need to specify a resistance
+ value, hence this can be specified as a boolean property.
+ For RSEL pull up type a resistance value (in ohms) can be added.
+
+ drive-open-drain: true
+
+ drive-push-pull: true
+
+ drive-strength:
+ enum: [ 2, 4, 8, 12 ]
+
+ drive-strength-microamp:
+ enum: [ 2000, 4000, 8000, 12000 ]
+
+ input-debounce-nanoseconds:
+ minimum: 0
+ maximum: 4294967295
+
+ input-disable: true
+
+ input-enable: true
+
+ input-schmitt-enable: true
+
+ input-schmitt-disable: true
+
+ power-source:
+ enum: [ 0, 1, 2 ]
+
+ slew-rate:
+ enum: [ 0, 1 ]
+ default: 0
+ description: |
+ 0: slow (half frequency)
+ 1: fast
+required:
+ - compatible
+ - reg
+ - resets
+ - interrupts
+ - interrupt-controller
+ - '#interrupt-cells'
+ - gpio-controller
+ - '#gpio-cells'
+ - gpio-ranges
+
+additionalProperties: false
+
+examples:
+ - |
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ pinctrl_sys0h: pinctrl@13080800 {
+ compatible = "starfive,jhb100-sys0h-pinctrl";
+ reg = <0x0 0x13080800 0x0 0x800>;
+ resets = <&sys0crg 3>;
+ interrupts = <57>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ gpio-ranges = <&pinctrl_sys0h 0 0 0 12>;
+ };
+ };
diff --git a/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h b/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h
index 6d8f5516a178..38d5a94e92e3 100644
--- a/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h
+++ b/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h
@@ -14,4 +14,18 @@
#define PADNUM_SYS0_GPIO_A2 2
#define PADNUM_SYS0_GPIO_A3 3
+/* sys0h pad numbers */
+#define PADNUM_SYS0H_GPIO_A4 0
+#define PADNUM_SYS0H_GPIO_A5 1
+#define PADNUM_SYS0H_GPIO_A6 2
+#define PADNUM_SYS0H_GPIO_A7 3
+#define PADNUM_SYS0H_GPIO_A8 4
+#define PADNUM_SYS0H_GPIO_A9 5
+#define PADNUM_SYS0H_GPIO_A10 6
+#define PADNUM_SYS0H_GPIO_A11 7
+#define PADNUM_SYS0H_GPIO_A12 8
+#define PADNUM_SYS0H_GPIO_A13 9
+#define PADNUM_SYS0H_GPIO_A14 10
+#define PADNUM_SYS0H_GPIO_A15 11
+
#endif
--
2.25.1
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply related [flat|nested] 32+ messages in thread* Re: [PATCH v2 06/22] dt-bindings: pinctrl: Add starfive,jhb100-sys0h-pinctrl
2026-05-14 11:12 ` [PATCH v2 06/22] dt-bindings: pinctrl: Add starfive,jhb100-sys0h-pinctrl Changhuang Liang
@ 2026-05-14 13:17 ` Rob Herring (Arm)
0 siblings, 0 replies; 32+ messages in thread
From: Rob Herring (Arm) @ 2026-05-14 13:17 UTC (permalink / raw)
To: Changhuang Liang
Cc: devicetree, Palmer Dabbelt, linux-gpio, linux-kernel, linux-riscv,
Krzysztof Kozlowski, Bartosz Golaszewski, Albert Ou, Conor Dooley,
Paul Walmsley, Emil Renner Berthing, Linus Walleij,
Alexandre Ghiti, Philipp Zabel, Lianfeng Ouyang
On Thu, 14 May 2026 04:12:02 -0700, Changhuang Liang wrote:
> Add pinctrl bindings for StarFive JHB100 SoC System-0 host(sys0h) pinctrl
> controller.
>
> Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
> ---
> .../starfive,jhb100-sys0h-pinctrl.yaml | 174 ++++++++++++++++++
> .../pinctrl/starfive,jhb100-pinctrl.h | 14 ++
> 2 files changed, 188 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys0h-pinctrl.yaml
>
My bot found errors running 'make dt_binding_check' on your patch:
yamllint warnings/errors:
./Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys0h-pinctrl.yaml:136:14: [warning] wrong indentation: expected 12 but found 13 (indentation)
./Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys0-pinctrl.yaml:136:14: [warning] wrong indentation: expected 12 but found 13 (indentation)
dtschema/dtc warnings/errors:
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys0h-pinctrl.example.dtb: pinctrl@13080800 (starfive,jhb100-sys0h-pinctrl): gpio-ranges:1: [12] is too short
from schema $id: http://devicetree.org/schemas/gpio/gpio.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys0-pinctrl.example.dtb: pinctrl@13080000 (starfive,jhb100-sys0-pinctrl): gpio-ranges:1: [4] is too short
from schema $id: http://devicetree.org/schemas/gpio/gpio.yaml
doc reference errors (make refcheckdocs):
See https://patchwork.kernel.org/project/devicetree/patch/20260514111218.94519-7-changhuang.liang@starfivetech.com
The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.
If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:
pip3 install dtschema --upgrade
Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply [flat|nested] 32+ messages in thread
* [PATCH v2 07/22] pinctrl: starfive: Add StarFive JHB100 sys0h controller driver
2026-05-14 11:11 [PATCH v2 00/22] Add basic pinctrl drivers for JHB100 SoC Changhuang Liang
` (5 preceding siblings ...)
2026-05-14 11:12 ` [PATCH v2 06/22] dt-bindings: pinctrl: Add starfive,jhb100-sys0h-pinctrl Changhuang Liang
@ 2026-05-14 11:12 ` Changhuang Liang
2026-05-14 11:12 ` [PATCH v2 08/22] dt-bindings: pinctrl: Add starfive,jhb100-sys1-pinctrl Changhuang Liang
` (14 subsequent siblings)
21 siblings, 0 replies; 32+ messages in thread
From: Changhuang Liang @ 2026-05-14 11:12 UTC (permalink / raw)
To: Linus Walleij, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Emil Renner Berthing, Paul Walmsley, Albert Ou, Palmer Dabbelt,
Alexandre Ghiti, Philipp Zabel, Bartosz Golaszewski
Cc: linux-gpio, linux-kernel, devicetree, linux-riscv,
Lianfeng Ouyang, Changhuang Liang
Add pinctrl driver for StarFive JHB100 SoC System-0 Host(sys0h) pinctrl
controller.
Co-developed-by: Lianfeng Ouyang <lianfeng.ouyang@starfivetech.com>
Signed-off-by: Lianfeng Ouyang <lianfeng.ouyang@starfivetech.com>
Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
---
drivers/pinctrl/starfive/Kconfig | 12 +++
drivers/pinctrl/starfive/Makefile | 1 +
.../starfive/pinctrl-starfive-jhb100-sys0h.c | 97 +++++++++++++++++++
3 files changed, 110 insertions(+)
create mode 100644 drivers/pinctrl/starfive/pinctrl-starfive-jhb100-sys0h.c
diff --git a/drivers/pinctrl/starfive/Kconfig b/drivers/pinctrl/starfive/Kconfig
index 548a1b133f81..1c87f64830ed 100644
--- a/drivers/pinctrl/starfive/Kconfig
+++ b/drivers/pinctrl/starfive/Kconfig
@@ -66,3 +66,15 @@ config PINCTRL_STARFIVE_JHB100_SYS0
This also provides an interface to the GPIO pins not used by other
peripherals supporting inputs, outputs, configuring pull-up/pull-down
and interrupts on input changes.
+
+config PINCTRL_STARFIVE_JHB100_SYS0H
+ tristate "StarFive JHB100 SoC System-0 Host pinctrl and GPIO driver"
+ depends on ARCH_STARFIVE || COMPILE_TEST
+ depends on OF
+ select PINCTRL_STARFIVE_JHB100
+ default ARCH_STARFIVE
+ help
+ Say yes here to support System-0 Host pin control on the StarFive JHB100 SoC.
+ This also provides an interface to the GPIO pins not used by other
+ peripherals supporting inputs, outputs, configuring pull-up/pull-down
+ and interrupts on input changes.
diff --git a/drivers/pinctrl/starfive/Makefile b/drivers/pinctrl/starfive/Makefile
index c0d368f413bc..b26156a6d0eb 100644
--- a/drivers/pinctrl/starfive/Makefile
+++ b/drivers/pinctrl/starfive/Makefile
@@ -8,3 +8,4 @@ obj-$(CONFIG_PINCTRL_STARFIVE_JH7110_AON) += pinctrl-starfive-jh7110-aon.o
obj-$(CONFIG_PINCTRL_STARFIVE_JHB100) += pinctrl-starfive-jhb100.o
obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_SYS0) += pinctrl-starfive-jhb100-sys0.o
+obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_SYS0H) += pinctrl-starfive-jhb100-sys0h.o
diff --git a/drivers/pinctrl/starfive/pinctrl-starfive-jhb100-sys0h.c b/drivers/pinctrl/starfive/pinctrl-starfive-jhb100-sys0h.c
new file mode 100644
index 000000000000..80dc35321a95
--- /dev/null
+++ b/drivers/pinctrl/starfive/pinctrl-starfive-jhb100-sys0h.c
@@ -0,0 +1,97 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Pinctrl / GPIO driver for StarFive JHB100 SoC System-0 host domain
+ *
+ * Copyright (C) 2024 StarFive Technology Co., Ltd.
+ * Author: Alex Soo <yuklin.soo@starfivetech.com>
+ *
+ */
+
+#include <dt-bindings/pinctrl/starfive,jhb100-pinctrl.h>
+#include <linux/mod_devicetable.h>
+#include <linux/platform_device.h>
+
+#include "pinctrl-starfive-jhb100.h"
+
+static const struct jhb100_pin_layout_desc jhb100_sys0h_pl_desc[] = {
+ { .pin_start = 0, .pin_cnt = 7, .name = "gpio", .gpio_func_sel = 0 },
+ { .pin_start = 7, .pin_cnt = 1, .name = "espi0_reset", .gpio_func_sel = 1 },
+ { .pin_start = 8, .pin_cnt = 4, .name = "gpio", .gpio_func_sel = 0 },
+ { 0xff },
+};
+
+static struct config_reg_layout_desc jhb100_sys0h_pinctrl_rl_desc[] = {
+ {
+ .pin_start = 0,
+ .pin_cnt = 12,
+ .drive_strength_2bit = { .shift = 0, .width = 2 },
+ .input_enable = { .shift = 2, .width = 1 },
+ .pull_down = { .shift = 3, .width = 1 },
+ .pull_up = { .shift = 4, .width = 1 },
+ .slew_rate = { .shift = 5, .width = 1 },
+ .schmitt_trigger_select = { .shift = 6, .width = 1 },
+ .reserved = { .shift = 7, .width = 8 },
+ .debounce_width = { .shift = 15, .width = 17 },
+ },
+ { 0xff },
+};
+
+struct starfive_pinctrl_regs jhb100_sys0h_pinctrl_regs = {
+ .func_sel = { .reg = 0x40, .width_per_pin = 2 },
+ .config = 0x04,
+ .output = 0x34,
+ .output_en = 0x38,
+ .gpio_status = 0x3c,
+ .irq_en = 0x44,
+ .irq_status = 0x48,
+ .irq_clr = 0x4c,
+ .irq_trigger = 0x50,
+ .irq_level = 0x54,
+ .irq_both_edge = 0x58,
+ .irq_edge = 0x5c,
+};
+
+static const struct jhb100_pinctrl_func_maps jhb100_func_maps_sys0h[] = {
+ { .func = "espi", .val = 1 },
+ { .func = "espi_reset", .val = 0 },
+ { .func = "espi0_vw", .val = 1 },
+ { .func = "espi1_vw", .val = 2 },
+ { .func = "gpio", .val = 0,
+ .max_pin = JHB100_FUNC_MAPS_MAX_PIN(PADNUM_SYS0H_GPIO_A10) },
+ { .func = "gpio", .val = 1,
+ .max_pin = JHB100_FUNC_MAPS_MAX_PIN(PADNUM_SYS0H_GPIO_A11) },
+ { .func = "gpio", .val = 0,
+ .max_pin = JHB100_FUNC_MAPS_MAX_PIN(PADNUM_SYS0H_GPIO_A15) },
+ { .func = "scap_trigger", .val = 3 },
+};
+
+static struct jhb100_pinctrl_domain_info jhb100_sys0h_pinctrl_info = {
+ .name = "jhb100-sys0h",
+ .pl_desc = jhb100_sys0h_pl_desc,
+ .crl_desc = jhb100_sys0h_pinctrl_rl_desc,
+ .regs = &jhb100_sys0h_pinctrl_regs,
+ .fmaps = jhb100_func_maps_sys0h,
+ .num_maps = ARRAY_SIZE(jhb100_func_maps_sys0h),
+};
+
+static const struct of_device_id jhb100_sys0h_pinctrl_of_match[] = {
+ {
+ .compatible = "starfive,jhb100-sys0h-pinctrl",
+ .data = &jhb100_sys0h_pinctrl_info,
+ },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, jhb100_sys0h_pinctrl_of_match);
+
+static struct platform_driver jhb100_sys0h_pinctrl_driver = {
+ .probe = jhb100_pinctrl_probe,
+ .driver = {
+ .name = "starfive-jhb100-sys0h-pinctrl",
+ .of_match_table = jhb100_sys0h_pinctrl_of_match,
+ },
+};
+module_platform_driver(jhb100_sys0h_pinctrl_driver);
+
+MODULE_DESCRIPTION("Pinctrl driver for StarFive JHB100 SoC System-0 host domain");
+MODULE_AUTHOR("Alex Soo <yuklin.soo@starfivetech.com>");
+MODULE_LICENSE("GPL");
--
2.25.1
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply related [flat|nested] 32+ messages in thread* [PATCH v2 08/22] dt-bindings: pinctrl: Add starfive,jhb100-sys1-pinctrl
2026-05-14 11:11 [PATCH v2 00/22] Add basic pinctrl drivers for JHB100 SoC Changhuang Liang
` (6 preceding siblings ...)
2026-05-14 11:12 ` [PATCH v2 07/22] pinctrl: starfive: Add StarFive JHB100 sys0h controller driver Changhuang Liang
@ 2026-05-14 11:12 ` Changhuang Liang
2026-05-14 11:12 ` [PATCH v2 09/22] pinctrl: starfive: Add StarFive JHB100 sys1 controller driver Changhuang Liang
` (13 subsequent siblings)
21 siblings, 0 replies; 32+ messages in thread
From: Changhuang Liang @ 2026-05-14 11:12 UTC (permalink / raw)
To: Linus Walleij, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Emil Renner Berthing, Paul Walmsley, Albert Ou, Palmer Dabbelt,
Alexandre Ghiti, Philipp Zabel, Bartosz Golaszewski
Cc: linux-gpio, linux-kernel, devicetree, linux-riscv,
Lianfeng Ouyang, Changhuang Liang
Add pinctrl bindings for StarFive JHB100 SoC System-1(sys1) pinctrl
controller.
Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
---
.../pinctrl/starfive,jhb100-sys1-pinctrl.yaml | 175 ++++++++++++++++++
.../pinctrl/starfive,jhb100-pinctrl.h | 10 +
2 files changed, 185 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys1-pinctrl.yaml
diff --git a/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys1-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys1-pinctrl.yaml
new file mode 100644
index 000000000000..f9a7998d11cb
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys1-pinctrl.yaml
@@ -0,0 +1,175 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/starfive,jhb100-sys1-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: StarFive JHB100 System-1 Pin Controller
+
+description: |
+ Pinctrl bindings for JHB100 RISC-V SoC from StarFive Technology Ltd.
+
+ The JHB100 SoC has 13 pinctrl domains - sys0, sys0h, sys1, sys2, per0, per1,
+ per2, per2pok, per3, adc0, adc1, emmc, and vga.
+ This document provides an overview of the "sys1" pinctrl domain.
+
+ The "sys1" domain has a pin controller which provides
+ - function selection for GPIO pads.
+ - GPIO pad configuration.
+ - GPIO interrupt handling.
+
+ In the SYS1 Pin Controller, there are 8 multi-function GPIO_PADs. Each of
+ them can be multiplexed to different hardware blocks through function
+ selection. Each iopad has a maximum of up to 4 functions - 0, 1, 2, and 3.
+ Function 0 is the default function which is generally the GPIO function
+ (or occasionally, it can be a peripheral signal).
+ Function 1, 2, and 3 are the alternate functions or peripheral signals that
+ can be routed to the iopad. The function selection can be carried out by
+ writing the function number to the iopad function select register.
+
+ Each iopad is configurable with parameters such as input-enable, internal
+ pull-up/pull-down bias, drive strength, schmitt trigger, slew rate, input
+ debounce nanoseconds, power source and drive type (open-drain or push-pull).
+
+maintainers:
+ - Alex Soo <yuklin.soo@starfivetech.com>
+
+properties:
+ compatible:
+ items:
+ - const: starfive,jhb100-sys1-pinctrl
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ resets:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ interrupt-controller: true
+
+ '#interrupt-cells':
+ const: 3
+
+ gpio-controller: true
+
+ '#gpio-cells':
+ const: 3
+
+ gpio-ranges: true
+
+ gpio-line-names: true
+
+patternProperties:
+ '-grp$':
+ type: object
+ additionalProperties: false
+ patternProperties:
+ '-pins$':
+ type: object
+ description: |
+ A pinctrl node should contain at least one subnode representing the
+ pinctrl groups available in the domain. Each subnode will list the
+ pins it needs, and how they should be configured, with regard to
+ function selection, bias, input enable/disable, input schmitt
+ trigger enable/disable, slew-rate, input debounce nanoseconds,
+ drive-open-drain, drive-push-pull, power-source and drive-strength.
+ allOf:
+ - $ref: /schemas/pinctrl/pincfg-node.yaml
+ - $ref: /schemas/pinctrl/pinmux-node.yaml
+ unevaluatedProperties: false
+
+ properties:
+ pins:
+ description:
+ The list of IOs that properties in the pincfg node apply to.
+
+ function:
+ description:
+ A string containing the name of the function to mux for these
+ pins.
+ enum: [ espi, espi_reset, gpio, host0_port80, host1_port80 ]
+
+ bias-disable: true
+
+ bias-pull-down:
+ type: boolean
+
+ bias-pull-up:
+ oneOf:
+ - type: boolean
+ - enum: [ 600, 900, 1200, 2000 ]
+ description: Pull up RSEL type resistance values (in ohms)
+ description:
+ For normal pull up type there is no need to specify a resistance
+ value, hence this can be specified as a boolean property.
+ For RSEL pull up type a resistance value (in ohms) can be added.
+
+ drive-open-drain: true
+
+ drive-push-pull: true
+
+ drive-strength:
+ enum: [ 2, 4, 8, 12 ]
+
+ drive-strength-microamp:
+ enum: [ 2000, 4000, 8000, 12000 ]
+
+ input-debounce-nanoseconds:
+ minimum: 0
+ maximum: 4294967295
+
+ input-disable: true
+
+ input-enable: true
+
+ input-schmitt-enable: true
+
+ input-schmitt-disable: true
+
+ power-source:
+ enum: [ 0, 1, 2 ]
+
+ slew-rate:
+ enum: [ 0, 1 ]
+ default: 0
+ description: |
+ 0: slow (half frequency)
+ 1: fast
+
+required:
+ - compatible
+ - reg
+ - resets
+ - interrupts
+ - interrupt-controller
+ - '#interrupt-cells'
+ - gpio-controller
+ - '#gpio-cells'
+ - gpio-ranges
+
+additionalProperties: false
+
+examples:
+ - |
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ pinctrl_sys1: pinctrl@13081000 {
+ compatible = "starfive,jhb100-sys1-pinctrl";
+ reg = <0x0 0x13081000 0x0 0x1000>;
+ resets = <&sys1crg 2>;
+ interrupts = <58>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ gpio-ranges = <&pinctrl_sys1 0 0 0 8>;
+ };
+ };
diff --git a/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h b/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h
index 38d5a94e92e3..30704a5a3418 100644
--- a/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h
+++ b/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h
@@ -28,4 +28,14 @@
#define PADNUM_SYS0H_GPIO_A14 10
#define PADNUM_SYS0H_GPIO_A15 11
+/* sys1 pad numbers */
+#define PADNUM_SYS1_GPIO_A16 0
+#define PADNUM_SYS1_GPIO_A17 1
+#define PADNUM_SYS1_GPIO_A18 2
+#define PADNUM_SYS1_GPIO_A19 3
+#define PADNUM_SYS1_GPIO_A20 4
+#define PADNUM_SYS1_GPIO_A21 5
+#define PADNUM_SYS1_GPIO_A22 6
+#define PADNUM_SYS1_GPIO_A23 7
+
#endif
--
2.25.1
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply related [flat|nested] 32+ messages in thread* [PATCH v2 09/22] pinctrl: starfive: Add StarFive JHB100 sys1 controller driver
2026-05-14 11:11 [PATCH v2 00/22] Add basic pinctrl drivers for JHB100 SoC Changhuang Liang
` (7 preceding siblings ...)
2026-05-14 11:12 ` [PATCH v2 08/22] dt-bindings: pinctrl: Add starfive,jhb100-sys1-pinctrl Changhuang Liang
@ 2026-05-14 11:12 ` Changhuang Liang
2026-05-14 11:12 ` [PATCH v2 10/22] dt-bindings: pinctrl: Add starfive,jhb100-sys2-pinctrl Changhuang Liang
` (12 subsequent siblings)
21 siblings, 0 replies; 32+ messages in thread
From: Changhuang Liang @ 2026-05-14 11:12 UTC (permalink / raw)
To: Linus Walleij, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Emil Renner Berthing, Paul Walmsley, Albert Ou, Palmer Dabbelt,
Alexandre Ghiti, Philipp Zabel, Bartosz Golaszewski
Cc: linux-gpio, linux-kernel, devicetree, linux-riscv,
Lianfeng Ouyang, Changhuang Liang
Add pinctrl driver for StarFive JHB100 SoC System-1(sys1) pinctrl
controller.
Co-developed-by: Lianfeng Ouyang <lianfeng.ouyang@starfivetech.com>
Signed-off-by: Lianfeng Ouyang <lianfeng.ouyang@starfivetech.com>
Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
---
drivers/pinctrl/starfive/Kconfig | 12 +++
drivers/pinctrl/starfive/Makefile | 1 +
.../starfive/pinctrl-starfive-jhb100-sys1.c | 93 +++++++++++++++++++
3 files changed, 106 insertions(+)
create mode 100644 drivers/pinctrl/starfive/pinctrl-starfive-jhb100-sys1.c
diff --git a/drivers/pinctrl/starfive/Kconfig b/drivers/pinctrl/starfive/Kconfig
index 1c87f64830ed..882d621eaf57 100644
--- a/drivers/pinctrl/starfive/Kconfig
+++ b/drivers/pinctrl/starfive/Kconfig
@@ -78,3 +78,15 @@ config PINCTRL_STARFIVE_JHB100_SYS0H
This also provides an interface to the GPIO pins not used by other
peripherals supporting inputs, outputs, configuring pull-up/pull-down
and interrupts on input changes.
+
+config PINCTRL_STARFIVE_JHB100_SYS1
+ tristate "StarFive JHB100 SoC System-1 pinctrl and GPIO driver"
+ depends on ARCH_STARFIVE || COMPILE_TEST
+ depends on OF
+ select PINCTRL_STARFIVE_JHB100
+ default ARCH_STARFIVE
+ help
+ Say yes here to support System-1 pin control on the StarFive JHB100 SoC.
+ This also provides an interface to the GPIO pins not used by other
+ peripherals supporting inputs, outputs, configuring pull-up/pull-down
+ and interrupts on input changes.
diff --git a/drivers/pinctrl/starfive/Makefile b/drivers/pinctrl/starfive/Makefile
index b26156a6d0eb..8d96cf80d377 100644
--- a/drivers/pinctrl/starfive/Makefile
+++ b/drivers/pinctrl/starfive/Makefile
@@ -9,3 +9,4 @@ obj-$(CONFIG_PINCTRL_STARFIVE_JH7110_AON) += pinctrl-starfive-jh7110-aon.o
obj-$(CONFIG_PINCTRL_STARFIVE_JHB100) += pinctrl-starfive-jhb100.o
obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_SYS0) += pinctrl-starfive-jhb100-sys0.o
obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_SYS0H) += pinctrl-starfive-jhb100-sys0h.o
+obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_SYS1) += pinctrl-starfive-jhb100-sys1.o
diff --git a/drivers/pinctrl/starfive/pinctrl-starfive-jhb100-sys1.c b/drivers/pinctrl/starfive/pinctrl-starfive-jhb100-sys1.c
new file mode 100644
index 000000000000..84ca7b33a5a4
--- /dev/null
+++ b/drivers/pinctrl/starfive/pinctrl-starfive-jhb100-sys1.c
@@ -0,0 +1,93 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Pinctrl / GPIO driver for StarFive JHB100 SoC System-1 domain
+ *
+ * Copyright (C) 2024 StarFive Technology Co., Ltd.
+ * Author: Alex Soo <yuklin.soo@starfivetech.com>
+ *
+ */
+
+#include <dt-bindings/pinctrl/starfive,jhb100-pinctrl.h>
+#include <linux/mod_devicetable.h>
+#include <linux/platform_device.h>
+
+#include "pinctrl-starfive-jhb100.h"
+
+static const struct jhb100_pin_layout_desc jhb100_sys1_pl_desc[] = {
+ { .pin_start = 0, .pin_cnt = 7, .name = "gpio", .gpio_func_sel = 0 },
+ { .pin_start = 7, .pin_cnt = 1, .name = "espi1_reset", .gpio_func_sel = 1 },
+ { 0xff },
+};
+
+static struct config_reg_layout_desc jhb100_sys1_pinctrl_rl_desc[] = {
+ {
+ .pin_start = 0,
+ .pin_cnt = 8,
+ .drive_strength_2bit = { .shift = 0, .width = 2 },
+ .input_enable = { .shift = 2, .width = 1 },
+ .pull_down = { .shift = 3, .width = 1 },
+ .pull_up = { .shift = 4, .width = 1 },
+ .slew_rate = { .shift = 5, .width = 1 },
+ .schmitt_trigger_select = { .shift = 6, .width = 1 },
+ .reserved = { .shift = 7, .width = 8 },
+ .debounce_width = { .shift = 15, .width = 17 },
+ },
+ { 0xff },
+};
+
+struct starfive_pinctrl_regs jhb100_sys1_pinctrl_regs = {
+ .func_sel = { .reg = 0x30, .width_per_pin = 2 },
+ .config = 0x04,
+ .output = 0x24,
+ .output_en = 0x28,
+ .gpio_status = 0x2c,
+ .irq_en = 0x34,
+ .irq_status = 0x38,
+ .irq_clr = 0x3c,
+ .irq_trigger = 0x40,
+ .irq_level = 0x44,
+ .irq_both_edge = 0x48,
+ .irq_edge = 0x4c,
+};
+
+static const struct jhb100_pinctrl_func_maps jhb100_func_maps_sys1[] = {
+ { .func = "espi", .val = 1 },
+ { .func = "espi_reset", .val = 0 },
+ { .func = "gpio", .val = 0,
+ .max_pin = JHB100_FUNC_MAPS_MAX_PIN(PADNUM_SYS1_GPIO_A22) },
+ { .func = "gpio", .val = 1,
+ .max_pin = JHB100_FUNC_MAPS_MAX_PIN(PADNUM_SYS1_GPIO_A23) },
+ { .func = "host0_port80", .val = 2 },
+ { .func = "host1_port80", .val = 3 },
+};
+
+static const struct jhb100_pinctrl_domain_info jhb100_sys1_pinctrl_info = {
+ .name = "jhb100-sys1",
+ .pl_desc = jhb100_sys1_pl_desc,
+ .crl_desc = jhb100_sys1_pinctrl_rl_desc,
+ .regs = &jhb100_sys1_pinctrl_regs,
+ .fmaps = jhb100_func_maps_sys1,
+ .num_maps = ARRAY_SIZE(jhb100_func_maps_sys1),
+};
+
+static const struct of_device_id jhb100_sys1_pinctrl_of_match[] = {
+ {
+ .compatible = "starfive,jhb100-sys1-pinctrl",
+ .data = &jhb100_sys1_pinctrl_info,
+ },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, jhb100_sys1_pinctrl_of_match);
+
+static struct platform_driver jhb100_sys1_pinctrl_driver = {
+ .probe = jhb100_pinctrl_probe,
+ .driver = {
+ .name = "starfive-jhb100-sys1-pinctrl",
+ .of_match_table = jhb100_sys1_pinctrl_of_match,
+ },
+};
+module_platform_driver(jhb100_sys1_pinctrl_driver);
+
+MODULE_DESCRIPTION("Pinctrl driver for StarFive JHB100 SoC System-1 domain");
+MODULE_AUTHOR("Alex Soo <yuklin.soo@starfivetech.com>");
+MODULE_LICENSE("GPL");
--
2.25.1
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply related [flat|nested] 32+ messages in thread* [PATCH v2 10/22] dt-bindings: pinctrl: Add starfive,jhb100-sys2-pinctrl
2026-05-14 11:11 [PATCH v2 00/22] Add basic pinctrl drivers for JHB100 SoC Changhuang Liang
` (8 preceding siblings ...)
2026-05-14 11:12 ` [PATCH v2 09/22] pinctrl: starfive: Add StarFive JHB100 sys1 controller driver Changhuang Liang
@ 2026-05-14 11:12 ` Changhuang Liang
2026-05-14 13:17 ` Rob Herring (Arm)
2026-05-14 11:12 ` [PATCH v2 11/22] pinctrl: starfive: Add StarFive JHB100 sys2 controller driver Changhuang Liang
` (11 subsequent siblings)
21 siblings, 1 reply; 32+ messages in thread
From: Changhuang Liang @ 2026-05-14 11:12 UTC (permalink / raw)
To: Linus Walleij, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Emil Renner Berthing, Paul Walmsley, Albert Ou, Palmer Dabbelt,
Alexandre Ghiti, Philipp Zabel, Bartosz Golaszewski
Cc: linux-gpio, linux-kernel, devicetree, linux-riscv,
Lianfeng Ouyang, Changhuang Liang
Add pinctrl bindings for StarFive JHB100 SoC System-2(sys2) pinctrl
controller.
System-2 domain also supports configuring the pin group voltage.
Add relevant definitions for power-source configuration.
Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
---
.../pinctrl/starfive,jhb100-sys2-pinctrl.yaml | 173 ++++++++++++++++++
.../pinctrl/starfive,jhb100-pinctrl.h | 44 +++++
2 files changed, 217 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys2-pinctrl.yaml
diff --git a/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys2-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys2-pinctrl.yaml
new file mode 100644
index 000000000000..3281c9433281
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys2-pinctrl.yaml
@@ -0,0 +1,173 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/starfive,jhb100-sys2-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: StarFive JHB100 System-2 Pin Controller
+
+description: |
+ Pinctrl bindings for JHB100 RISC-V SoC from StarFive Technology Ltd.
+
+ The JHB100 SoC has 13 pinctrl domains - sys0, sys0h, sys1, sys2, per0, per1,
+ per2, per2pok, per3, adc0, adc1, emmc, and vga.
+ This document provides an overview of the "sys2" pinctrl domain.
+
+ The "sys2" domain has a pin controller which provides
+ - function selection for GPIO pads.
+ - GPIO pad configuration.
+ - GPIO interrupt handling.
+
+ In the SYS2 Pin Controller, there are 37 multi-function GPIO_PADs. Each of
+ them can be multiplexed to different hardware blocks through function
+ selection. Each iopad has a maximum of up to 4 functions - 0, 1, 2, and 3.
+ Function 0 is the default function which is the GPIO function.
+ Function 1, 2, and 3 are the alternate functions or peripheral signals that
+ can be routed to the iopad. The function selection can be carried out by
+ writing the function number to the iopad function select register.
+
+ Each iopad is configurable with parameters such as input-enable, internal
+ pull-up/pull-down bias, drive strength, schmitt trigger, slew rate, input
+ debounce nanoseconds, power source and drive type (open-drain or push-pull).
+
+maintainers:
+ - Alex Soo <yuklin.soo@starfivetech.com>
+
+properties:
+ compatible:
+ items:
+ - const: starfive,jhb100-sys2-pinctrl
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ resets:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ interrupt-controller: true
+
+ '#interrupt-cells':
+ const: 3
+
+ gpio-controller: true
+
+ '#gpio-cells':
+ const: 3
+
+ gpio-ranges: true
+
+ gpio-line-names: true
+
+patternProperties:
+ '-grp$':
+ type: object
+ additionalProperties: false
+ patternProperties:
+ '-pins$':
+ type: object
+ description: |
+ A pinctrl node should contain at least one subnode representing the
+ pinctrl groups available in the domain. Each subnode will list the
+ pins it needs, and how they should be configured, with regard to
+ function selection, bias, input enable/disable, input schmitt
+ trigger enable/disable, slew-rate, input debounce nanoseconds,
+ drive-open-drain, drive-push-pull, power-source and drive-strength.
+ allOf:
+ - $ref: /schemas/pinctrl/pincfg-node.yaml
+ - $ref: /schemas/pinctrl/pinmux-node.yaml
+ unevaluatedProperties: false
+
+ properties:
+ pins:
+ description:
+ The list of IOs that properties in the pincfg node apply to.
+
+ function:
+ description:
+ A string containing the name of the function to mux for these
+ pins.
+ enum: [ gpio, host0_port80, host1_port80, jtag, smbalert, uart ]
+
+ bias-disable: true
+
+ bias-pull-down:
+ type: boolean
+
+ bias-pull-up:
+ oneOf:
+ - type: boolean
+ - enum: [ 600, 900, 1200, 2000 ]
+ description: Pull up RSEL type resistance values (in ohms)
+ description:
+ For normal pull up type there is no need to specify a resistance
+ value, hence this can be specified as a boolean property.
+ For RSEL pull up type a resistance value (in ohms) can be added.
+
+ drive-open-drain: true
+
+ drive-push-pull: true
+
+ drive-strength:
+ enum: [ 2, 4, 8, 12 ]
+
+ drive-strength-microamp:
+ enum: [ 2000, 4000, 8000, 12000 ]
+
+ input-debounce-nanoseconds:
+ minimum: 0
+ maximum: 4294967295
+
+ input-disable: true
+
+ input-enable: true
+
+ input-schmitt-enable: true
+
+ input-schmitt-disable: true
+
+ power-source:
+ enum: [ 0, 1, 2 ]
+
+ slew-rate:
+ enum: [ 0, 1 ]
+ default: 0
+ description: |
+ 0: slow (half frequency)
+ 1: fast
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - interrupt-controller
+ - '#interrupt-cells'
+ - gpio-controller
+ - '#gpio-cells'
+ - gpio-ranges
+
+additionalProperties: false
+
+examples:
+ - |
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ pinctrl_sys2: pinctrl@13082000 {
+ compatible = "starfive,jhb100-sys2-pinctrl";
+ reg = <0x0 0x13082000 0x0 0x1000>;
+ interrupts = <59>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ gpio-ranges = <&pinctrl_sys2 0 0 0 32>,
+ <&pinctrl_sys2 1 0 32 5>;
+ };
+ };
diff --git a/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h b/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h
index 30704a5a3418..89d344763540 100644
--- a/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h
+++ b/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h
@@ -38,4 +38,48 @@
#define PADNUM_SYS1_GPIO_A22 6
#define PADNUM_SYS1_GPIO_A23 7
+/* sys2 pad numbers */
+#define PADNUM_SYS2_GPIO_A24 0
+#define PADNUM_SYS2_GPIO_A25 1
+#define PADNUM_SYS2_GPIO_A26 2
+#define PADNUM_SYS2_GPIO_A27 3
+#define PADNUM_SYS2_GPIO_A28 4
+#define PADNUM_SYS2_GPIO_A29 5
+#define PADNUM_SYS2_GPIO_A30 6
+#define PADNUM_SYS2_GPIO_A31 7
+#define PADNUM_SYS2_GPIO_A32 8
+#define PADNUM_SYS2_GPIO_A33 9
+#define PADNUM_SYS2_GPIO_A34 10
+#define PADNUM_SYS2_GPIO_A35 11
+#define PADNUM_SYS2_GPIO_A36 12
+#define PADNUM_SYS2_GPIO_A37 13
+#define PADNUM_SYS2_GPIO_A38 14
+#define PADNUM_SYS2_GPIO_A39 15
+#define PADNUM_SYS2_GPIO_A40 16
+#define PADNUM_SYS2_GPIO_A41 17
+#define PADNUM_SYS2_GPIO_A42 18
+#define PADNUM_SYS2_GPIO_A43 19
+#define PADNUM_SYS2_GPIO_A44 20
+#define PADNUM_SYS2_GPIO_A45 21
+#define PADNUM_SYS2_GPIO_A46 22
+#define PADNUM_SYS2_GPIO_A47 23
+#define PADNUM_SYS2_GPIO_A48 24
+#define PADNUM_SYS2_GPIO_A49 25
+#define PADNUM_SYS2_GPIO_A50 26
+#define PADNUM_SYS2_GPIO_A51 27
+#define PADNUM_SYS2_GPIO_A52 28
+#define PADNUM_SYS2_GPIO_A53 29
+#define PADNUM_SYS2_GPIO_A54 30
+#define PADNUM_SYS2_GPIO_A55 31
+#define PADNUM_SYS2_GPIO_A56 32
+#define PADNUM_SYS2_GPIO_A57 33
+#define PADNUM_SYS2_GPIO_A58 34
+#define PADNUM_SYS2_GPIO_A59 35
+#define PADNUM_SYS2_GPIO_A60 36
+
+/* pinctrl hog power-source value */
+#define JHB100_PINVREF_3_3V 0
+#define JHB100_PINVREF_2_5V 1
+#define JHB100_PINVREF_1_8V 2
+
#endif
--
2.25.1
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply related [flat|nested] 32+ messages in thread* Re: [PATCH v2 10/22] dt-bindings: pinctrl: Add starfive,jhb100-sys2-pinctrl
2026-05-14 11:12 ` [PATCH v2 10/22] dt-bindings: pinctrl: Add starfive,jhb100-sys2-pinctrl Changhuang Liang
@ 2026-05-14 13:17 ` Rob Herring (Arm)
0 siblings, 0 replies; 32+ messages in thread
From: Rob Herring (Arm) @ 2026-05-14 13:17 UTC (permalink / raw)
To: Changhuang Liang
Cc: Philipp Zabel, Conor Dooley, Emil Renner Berthing, Paul Walmsley,
Linus Walleij, Palmer Dabbelt, Bartosz Golaszewski, linux-gpio,
linux-kernel, linux-riscv, devicetree, Alexandre Ghiti, Albert Ou,
Krzysztof Kozlowski, Lianfeng Ouyang
On Thu, 14 May 2026 04:12:06 -0700, Changhuang Liang wrote:
> Add pinctrl bindings for StarFive JHB100 SoC System-2(sys2) pinctrl
> controller.
>
> System-2 domain also supports configuring the pin group voltage.
> Add relevant definitions for power-source configuration.
>
> Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
> ---
> .../pinctrl/starfive,jhb100-sys2-pinctrl.yaml | 173 ++++++++++++++++++
> .../pinctrl/starfive,jhb100-pinctrl.h | 44 +++++
> 2 files changed, 217 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys2-pinctrl.yaml
>
My bot found errors running 'make dt_binding_check' on your patch:
yamllint warnings/errors:
./Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys2-pinctrl.yaml:135:14: [warning] wrong indentation: expected 12 but found 13 (indentation)
./Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys1-pinctrl.yaml:136:14: [warning] wrong indentation: expected 12 but found 13 (indentation)
./Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys0h-pinctrl.yaml:136:14: [warning] wrong indentation: expected 12 but found 13 (indentation)
./Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys0-pinctrl.yaml:136:14: [warning] wrong indentation: expected 12 but found 13 (indentation)
dtschema/dtc warnings/errors:
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/pci/toshiba,tc9563.example.dtb: pcie@0,0 (pci1179,0623): i2c-parent: [[4294967295, 119]] is too short
from schema $id: http://devicetree.org/schemas/pci/toshiba,tc9563.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/i2c/i2c-demux-pinctrl.example.dtb: i2c-mux3 (i2c-demux-pinctrl): i2c-parent:0: [2, 3, 4] is too long
from schema $id: http://devicetree.org/schemas/i2c/i2c-demux-pinctrl.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/net/renesas,ether.example.dtb: ethernet-phy@1 (ethernet-phy-id0022.1537): compatible: ['ethernet-phy-id0022.1537', 'ethernet-phy-ieee802.3-c22'] is too long
from schema $id: http://devicetree.org/schemas/net/micrel.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys1-pinctrl.example.dtb: pinctrl@13081000 (starfive,jhb100-sys1-pinctrl): gpio-ranges:1: [8] is too short
from schema $id: http://devicetree.org/schemas/gpio/gpio.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys0h-pinctrl.example.dtb: pinctrl@13080800 (starfive,jhb100-sys0h-pinctrl): gpio-ranges:1: [12] is too short
from schema $id: http://devicetree.org/schemas/gpio/gpio.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys0-pinctrl.example.dtb: pinctrl@13080000 (starfive,jhb100-sys0-pinctrl): gpio-ranges:1: [4] is too short
from schema $id: http://devicetree.org/schemas/gpio/gpio.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/usb/ti,keystone-dwc3.example.dtb: dwc3@2680000 (ti,keystone-dwc3): usb@2690000:usb-phy:0: [4294967295, 4294967295] is too long
from schema $id: http://devicetree.org/schemas/usb/ti,keystone-dwc3.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/usb/ti,keystone-dwc3.example.dtb: dwc3@2680000 (ti,keystone-dwc3): usb@2690000: Unevaluated properties are not allowed ('usb-phy' was unexpected)
from schema $id: http://devicetree.org/schemas/usb/ti,keystone-dwc3.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/usb/ti,keystone-dwc3.example.dtb: usb@2690000 (snps,dwc3): usb-phy:0: [4294967295, 4294967295] is too long
from schema $id: http://devicetree.org/schemas/usb/snps,dwc3.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/usb/ti,keystone-dwc3.example.dtb: usb@2690000 (snps,dwc3): Unevaluated properties are not allowed ('usb-phy' was unexpected)
from schema $id: http://devicetree.org/schemas/usb/snps,dwc3.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/usb/snps,dwc3.example.dtb: usb@4a030000 (snps,dwc3): usb-phy:0: [4294967295, 4294967295] is too long
from schema $id: http://devicetree.org/schemas/usb/snps,dwc3.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/usb/snps,dwc3.example.dtb: usb@4a030000 (snps,dwc3): Unevaluated properties are not allowed ('snps,incr-burst-type-adjustment', 'usb-phy' were unexpected)
from schema $id: http://devicetree.org/schemas/usb/snps,dwc3.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/usb/usb-drd.example.dtb: usb@4a030000 (snps,dwc3): usb-phy:0: [4294967295, 4294967295] is too long
from schema $id: http://devicetree.org/schemas/usb/snps,dwc3.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/usb/usb-drd.example.dtb: usb@4a030000 (snps,dwc3): Unevaluated properties are not allowed ('adp-disable', 'dr_mode', 'maximum-speed', 'otg-rev', 'phy_type', 'usb-phy' were unexpected)
from schema $id: http://devicetree.org/schemas/usb/snps,dwc3.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys2-pinctrl.example.dtb: pinctrl@13082000 (starfive,jhb100-sys2-pinctrl): gpio-ranges:2: [32, 5] is too short
from schema $id: http://devicetree.org/schemas/gpio/gpio.yaml
doc reference errors (make refcheckdocs):
See https://patchwork.kernel.org/project/devicetree/patch/20260514111218.94519-11-changhuang.liang@starfivetech.com
The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.
If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:
pip3 install dtschema --upgrade
Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply [flat|nested] 32+ messages in thread
* [PATCH v2 11/22] pinctrl: starfive: Add StarFive JHB100 sys2 controller driver
2026-05-14 11:11 [PATCH v2 00/22] Add basic pinctrl drivers for JHB100 SoC Changhuang Liang
` (9 preceding siblings ...)
2026-05-14 11:12 ` [PATCH v2 10/22] dt-bindings: pinctrl: Add starfive,jhb100-sys2-pinctrl Changhuang Liang
@ 2026-05-14 11:12 ` Changhuang Liang
2026-05-14 11:12 ` [PATCH v2 12/22] dt-bindings: pinctrl: Add starfive,jhb100-per0-pinctrl Changhuang Liang
` (10 subsequent siblings)
21 siblings, 0 replies; 32+ messages in thread
From: Changhuang Liang @ 2026-05-14 11:12 UTC (permalink / raw)
To: Linus Walleij, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Emil Renner Berthing, Paul Walmsley, Albert Ou, Palmer Dabbelt,
Alexandre Ghiti, Philipp Zabel, Bartosz Golaszewski
Cc: linux-gpio, linux-kernel, devicetree, linux-riscv,
Lianfeng Ouyang, Changhuang Liang
Add pinctrl driver for StarFive JHB100 SoC System-2(sys2) pinctrl
controller.
Co-developed-by: Lianfeng Ouyang <lianfeng.ouyang@starfivetech.com>
Signed-off-by: Lianfeng Ouyang <lianfeng.ouyang@starfivetech.com>
Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
---
drivers/pinctrl/starfive/Kconfig | 12 ++
drivers/pinctrl/starfive/Makefile | 1 +
.../starfive/pinctrl-starfive-jhb100-sys2.c | 134 ++++++++++++++++++
3 files changed, 147 insertions(+)
create mode 100644 drivers/pinctrl/starfive/pinctrl-starfive-jhb100-sys2.c
diff --git a/drivers/pinctrl/starfive/Kconfig b/drivers/pinctrl/starfive/Kconfig
index 882d621eaf57..da11d486779a 100644
--- a/drivers/pinctrl/starfive/Kconfig
+++ b/drivers/pinctrl/starfive/Kconfig
@@ -90,3 +90,15 @@ config PINCTRL_STARFIVE_JHB100_SYS1
This also provides an interface to the GPIO pins not used by other
peripherals supporting inputs, outputs, configuring pull-up/pull-down
and interrupts on input changes.
+
+config PINCTRL_STARFIVE_JHB100_SYS2
+ tristate "StarFive JHB100 SoC System-2 pinctrl and GPIO driver"
+ depends on ARCH_STARFIVE || COMPILE_TEST
+ depends on OF
+ select PINCTRL_STARFIVE_JHB100
+ default ARCH_STARFIVE
+ help
+ Say yes here to support System-2 pin control on the StarFive JHB100 SoC.
+ This also provides an interface to the GPIO pins not used by other
+ peripherals supporting inputs, outputs, configuring pull-up/pull-down
+ and interrupts on input changes.
diff --git a/drivers/pinctrl/starfive/Makefile b/drivers/pinctrl/starfive/Makefile
index 8d96cf80d377..b817ad93b91d 100644
--- a/drivers/pinctrl/starfive/Makefile
+++ b/drivers/pinctrl/starfive/Makefile
@@ -10,3 +10,4 @@ obj-$(CONFIG_PINCTRL_STARFIVE_JHB100) += pinctrl-starfive-jhb100.o
obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_SYS0) += pinctrl-starfive-jhb100-sys0.o
obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_SYS0H) += pinctrl-starfive-jhb100-sys0h.o
obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_SYS1) += pinctrl-starfive-jhb100-sys1.o
+obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_SYS2) += pinctrl-starfive-jhb100-sys2.o
diff --git a/drivers/pinctrl/starfive/pinctrl-starfive-jhb100-sys2.c b/drivers/pinctrl/starfive/pinctrl-starfive-jhb100-sys2.c
new file mode 100644
index 000000000000..2601eb7b5b59
--- /dev/null
+++ b/drivers/pinctrl/starfive/pinctrl-starfive-jhb100-sys2.c
@@ -0,0 +1,134 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Pinctrl / GPIO driver for StarFive JHB100 SoC System-2 domain
+ *
+ * Copyright (C) 2024 StarFive Technology Co., Ltd.
+ * Author: Alex Soo <yuklin.soo@starfivetech.com>
+ *
+ */
+
+#include <dt-bindings/pinctrl/starfive,jhb100-pinctrl.h>
+#include <linux/mod_devicetable.h>
+#include <linux/platform_device.h>
+
+#include "pinctrl-starfive-jhb100.h"
+
+static const struct jhb100_pin_layout_desc jhb100_sys2_pl_desc[] = {
+ { .pin_start = 0, .pin_cnt = 37, .name = "gpio", .gpio_func_sel = 0 },
+ { .pin_start = 37, .pin_cnt = 1, .name = "jtag_tck", .gpio_func_sel = -1 },
+ { .pin_start = 38, .pin_cnt = 1, .name = "jtag_tresetn", .gpio_func_sel = -1 },
+ { .pin_start = 39, .pin_cnt = 1, .name = "jtag_tmc", .gpio_func_sel = -1 },
+ { .pin_start = 40, .pin_cnt = 1, .name = "jtag_tdi", .gpio_func_sel = -1 },
+ { .pin_start = 41, .pin_cnt = 1, .name = "jtag_tdo", .gpio_func_sel = -1 },
+ { .pin_start = 42, .pin_cnt = 1, .name = "jtag_hpd", .gpio_func_sel = -1 },
+ { 0xff },
+};
+
+static struct config_reg_layout_desc jhb100_sys2_pinctrl_rl_desc[] = {
+ {
+ .pin_start = 0,
+ .pin_cnt = 37,
+ .drive_strength_2bit = { .shift = 0, .width = 2 },
+ .input_enable = { .shift = 2, .width = 1 },
+ .pull_down = { .shift = 3, .width = 1 },
+ .pull_up = { .shift = 4, .width = 1 },
+ .slew_rate = { .shift = 5, .width = 1 },
+ .schmitt_trigger_select = { .shift = 6, .width = 1 },
+ .reserved = { .shift = 7, .width = 8 },
+ .debounce_width = { .shift = 15, .width = 17 },
+ },
+ {
+ .pin_start = 37,
+ .pin_cnt = 5,
+ .drive_strength_2bit = { .shift = 0, .width = 2 },
+ .input_enable = { .shift = 2, .width = 1 },
+ .pull_down = { .shift = 3, .width = 1 },
+ .pull_up = { .shift = 4, .width = 1 },
+ .slew_rate = { .shift = 5, .width = 1 },
+ .schmitt_trigger_select = { .shift = 6, .width = 1 },
+ .reserved = { .shift = 7, .width = 25 },
+ },
+ { 0xff },
+};
+
+static const struct pinvref_desc pinvref_desc_sys2[] = {
+ {
+ .name = "gpiow0",
+ .pin_grp = {
+ PADNUM_SYS2_GPIO_A36,
+ PADNUM_SYS2_GPIO_A37,
+ PADNUM_SYS2_GPIO_A38,
+ PADNUM_SYS2_GPIO_A39
+ },
+ .num_pins = 4,
+ .range = BIT(JHB100_PINVREF_1_8V) | BIT(JHB100_PINVREF_3_3V)
+ },
+ {
+ .name = "gpiow-inner",
+ .pin_grp = {
+ PADNUM_SYS2_GPIO_A40,
+ PADNUM_SYS2_GPIO_A41,
+ PADNUM_SYS2_GPIO_A42,
+ PADNUM_SYS2_GPIO_A43
+ },
+ .num_pins = 4,
+ .range = BIT(JHB100_PINVREF_1_8V) | BIT(JHB100_PINVREF_3_3V)
+ },
+ { NULL },
+};
+
+struct starfive_pinctrl_regs jhb100_sys2_pinctrl_regs = {
+ .vref = { .reg = 0x000, .pv_desc = pinvref_desc_sys2 },
+ .func_sel = { .reg = 0x0d4, .width_per_pin = 2 },
+ .config = 0x010,
+ .output = 0x0bc,
+ .output_en = 0x0c4,
+ .gpio_status = 0x0cc,
+ .irq_en = 0x0e0,
+ .irq_status = 0x0e8,
+ .irq_clr = 0x0f0,
+ .irq_trigger = 0x0f8,
+ .irq_level = 0x100,
+ .irq_both_edge = 0x108,
+ .irq_edge = 0x110,
+};
+
+static const struct jhb100_pinctrl_func_maps jhb100_func_maps_sys2[] = {
+ { .func = "gpio", .val = 0 },
+ { .func = "host0_port80", .val = 2 },
+ { .func = "host1_port80", .val = 3 },
+ { .func = "jtag", .val = 2 },
+ { .func = "smbalert", .val = 2 },
+ { .func = "uart", .val = 1 },
+};
+
+static const struct jhb100_pinctrl_domain_info jhb100_sys2_pinctrl_info = {
+ .name = "jhb100-sys2",
+ .pl_desc = jhb100_sys2_pl_desc,
+ .crl_desc = jhb100_sys2_pinctrl_rl_desc,
+ .regs = &jhb100_sys2_pinctrl_regs,
+ .fmaps = jhb100_func_maps_sys2,
+ .num_maps = ARRAY_SIZE(jhb100_func_maps_sys2),
+};
+
+static const struct of_device_id jhb100_sys2_pinctrl_of_match[] = {
+ {
+ .compatible = "starfive,jhb100-sys2-pinctrl",
+ .data = &jhb100_sys2_pinctrl_info,
+ },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, jhb100_sys2_pinctrl_of_match);
+
+static struct platform_driver jhb100_sys2_pinctrl_driver = {
+ .probe = jhb100_pinctrl_probe,
+ .driver = {
+ .name = "starfive-jhb100-sys2-pinctrl",
+ .of_match_table = jhb100_sys2_pinctrl_of_match,
+ },
+};
+module_platform_driver(jhb100_sys2_pinctrl_driver);
+
+MODULE_DESCRIPTION("Pinctrl driver for StarFive JHB100 SoC System-2 domain");
+MODULE_AUTHOR("Alex Soo <yuklin.soo@starfivetech.com>");
+MODULE_LICENSE("GPL");
--
2.25.1
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply related [flat|nested] 32+ messages in thread* [PATCH v2 12/22] dt-bindings: pinctrl: Add starfive,jhb100-per0-pinctrl
2026-05-14 11:11 [PATCH v2 00/22] Add basic pinctrl drivers for JHB100 SoC Changhuang Liang
` (10 preceding siblings ...)
2026-05-14 11:12 ` [PATCH v2 11/22] pinctrl: starfive: Add StarFive JHB100 sys2 controller driver Changhuang Liang
@ 2026-05-14 11:12 ` Changhuang Liang
2026-05-14 13:17 ` Rob Herring (Arm)
2026-05-14 11:12 ` [PATCH v2 13/22] pinctrl: starfive: Add StarFive JHB100 per0 controller driver Changhuang Liang
` (9 subsequent siblings)
21 siblings, 1 reply; 32+ messages in thread
From: Changhuang Liang @ 2026-05-14 11:12 UTC (permalink / raw)
To: Linus Walleij, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Emil Renner Berthing, Paul Walmsley, Albert Ou, Palmer Dabbelt,
Alexandre Ghiti, Philipp Zabel, Bartosz Golaszewski
Cc: linux-gpio, linux-kernel, devicetree, linux-riscv,
Lianfeng Ouyang, Changhuang Liang
Add pinctrl bindings for StarFive JHB100 SoC Peripheral-0(per0) pinctrl
controller.
Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
---
.../pinctrl/starfive,jhb100-per0-pinctrl.yaml | 176 ++++++++++++++++++
.../pinctrl/starfive,jhb100-pinctrl.h | 62 ++++++
2 files changed, 238 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per0-pinctrl.yaml
diff --git a/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per0-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per0-pinctrl.yaml
new file mode 100644
index 000000000000..9f2144c55844
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per0-pinctrl.yaml
@@ -0,0 +1,176 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/starfive,jhb100-per0-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: StarFive JHB100 Peripheral-0 Pin Controller
+
+description: |
+ Pinctrl bindings for JHB100 RISC-V SoC from StarFive Technology Ltd.
+
+ The JHB100 SoC has 13 pinctrl domains - sys0, sys0h, sys1, sys2, per0, per1,
+ per2, per2pok, per3, adc0, adc1, emmc, and vga.
+ This document provides an overview of the "per0" pinctrl domain.
+
+ The "per0" domain has a pin controller which provides
+ - function selection for GPIO pads.
+ - GPIO pad configuration.
+ - GPIO interrupt handling.
+
+ In the Peripheral-0 Pin Controller, there are 60 multi-function GPIO_PADs.
+ Each of them can be multiplexed to several hardware blocks through function
+ selection. Each iopad has a maximum of up to 3 functions - 0, 1, and 2.
+ Function 0 is the default function which is generally the GPIO function.
+ Function 1 and 2 are the alternate function or signal of an iopad. The
+ function 1 and function 2 are other optional functions or peripheral
+ signals that can be routed to an iopad. The function selection can be carried
+ out by writing the function number to the iopad function select register.
+
+ Each iopad is configurable with parameters such as input-enable, internal
+ pull-up/pull-down bias, drive strength, schmitt trigger, slew rate, input
+ debounce nanoseconds, power source and drive type (open-drain or push-pull).
+
+maintainers:
+ - Alex Soo <yuklin.soo@starfivetech.com>
+
+properties:
+ compatible:
+ items:
+ - const: starfive,jhb100-per0-pinctrl
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ resets:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ interrupt-controller: true
+
+ '#interrupt-cells':
+ const: 3
+
+ gpio-controller: true
+
+ '#gpio-cells':
+ const: 3
+
+ gpio-ranges: true
+
+ gpio-line-names: true
+
+patternProperties:
+ '-grp$':
+ type: object
+ additionalProperties: false
+ patternProperties:
+ '-pins$':
+ type: object
+ description: |
+ A pinctrl node should contain at least one subnode representing the
+ pinctrl groups available in the domain. Each subnode will list the
+ pins it needs, and how they should be configured, with regard to
+ function selection, bias, input enable/disable, input schmitt
+ trigger enable/disable, slew-rate, input debounce nanoseconds,
+ drive-open-drain, drive-push-pull, power-source and drive-strength.
+ allOf:
+ - $ref: /schemas/pinctrl/pincfg-node.yaml
+ - $ref: /schemas/pinctrl/pinmux-node.yaml
+ unevaluatedProperties: false
+
+ properties:
+ pins:
+ description:
+ The list of IOs that properties in the pincfg node apply to.
+
+ function:
+ description:
+ A string containing the name of the function to mux for these
+ pins.
+ enum: [ gmac_mdio, gpio, i2c, i3c, smbalert, wdt ]
+
+ bias-disable: true
+
+ bias-pull-down:
+ type: boolean
+
+ bias-pull-up:
+ oneOf:
+ - type: boolean
+ - enum: [ 600, 900, 1200, 2000 ]
+ description: Pull up RSEL type resistance values (in ohms)
+ description:
+ For normal pull up type there is no need to specify a resistance
+ value, hence this can be specified as a boolean property.
+ For RSEL pull up type a resistance value (in ohms) can be added.
+
+ drive-open-drain: true
+
+ drive-push-pull: true
+
+ drive-strength:
+ enum: [ 2, 4, 8, 12 ]
+
+ drive-strength-microamp:
+ enum: [ 2000, 4000, 8000, 12000 ]
+
+ input-debounce-nanoseconds:
+ minimum: 0
+ maximum: 4294967295
+
+ input-disable: true
+
+ input-enable: true
+
+ input-schmitt-enable: true
+
+ input-schmitt-disable: true
+
+ power-source:
+ enum: [ 0, 1, 2 ]
+
+ slew-rate:
+ enum: [ 0, 1 ]
+ default: 0
+ description: |
+ 0: slow (half frequency)
+ 1: fast
+
+required:
+ - compatible
+ - reg
+ - resets
+ - interrupts
+ - interrupt-controller
+ - '#interrupt-cells'
+ - gpio-controller
+ - '#gpio-cells'
+ - gpio-ranges
+
+additionalProperties: false
+
+examples:
+ - |
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ pinctrl_per0: pinctrl@11a0a000 {
+ compatible = "starfive,jhb100-per0-pinctrl";
+ reg = <0x0 0x11a0a000 0x0 0x1000>;
+ resets = <&per0crg 0>;
+ interrupts = <60>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ gpio-ranges = <&pinctrl_per0 0 0 0 32>,
+ <&pinctrl_per0 1 0 32 28>;
+ };
+ };
diff --git a/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h b/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h
index 89d344763540..0a8494b577e0 100644
--- a/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h
+++ b/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h
@@ -77,6 +77,68 @@
#define PADNUM_SYS2_GPIO_A59 35
#define PADNUM_SYS2_GPIO_A60 36
+/* per0 pad numbers */
+#define PADNUM_PER0_GPIO_B0 0
+#define PADNUM_PER0_GPIO_B1 1
+#define PADNUM_PER0_GPIO_B2 2
+#define PADNUM_PER0_GPIO_B3 3
+#define PADNUM_PER0_GPIO_B4 4
+#define PADNUM_PER0_GPIO_B5 5
+#define PADNUM_PER0_GPIO_B6 6
+#define PADNUM_PER0_GPIO_B7 7
+#define PADNUM_PER0_GPIO_B8 8
+#define PADNUM_PER0_GPIO_B9 9
+#define PADNUM_PER0_GPIO_B10 10
+#define PADNUM_PER0_GPIO_B11 11
+#define PADNUM_PER0_GPIO_B12 12
+#define PADNUM_PER0_GPIO_B13 13
+#define PADNUM_PER0_GPIO_B14 14
+#define PADNUM_PER0_GPIO_B15 15
+#define PADNUM_PER0_GPIO_B16 16
+#define PADNUM_PER0_GPIO_B17 17
+#define PADNUM_PER0_GPIO_B18 18
+#define PADNUM_PER0_GPIO_B19 19
+#define PADNUM_PER0_GPIO_B20 20
+#define PADNUM_PER0_GPIO_B21 21
+#define PADNUM_PER0_GPIO_B22 22
+#define PADNUM_PER0_GPIO_B23 23
+#define PADNUM_PER0_GPIO_B24 24
+#define PADNUM_PER0_GPIO_B25 25
+#define PADNUM_PER0_GPIO_B26 26
+#define PADNUM_PER0_GPIO_B27 27
+#define PADNUM_PER0_GPIO_B28 28
+#define PADNUM_PER0_GPIO_B29 29
+#define PADNUM_PER0_GPIO_B30 30
+#define PADNUM_PER0_GPIO_B31 31
+#define PADNUM_PER0_GPIO_B32 32
+#define PADNUM_PER0_GPIO_B33 33
+#define PADNUM_PER0_GPIO_B34 34
+#define PADNUM_PER0_GPIO_B35 35
+#define PADNUM_PER0_GPIO_B36 36
+#define PADNUM_PER0_GPIO_B37 37
+#define PADNUM_PER0_GPIO_B38 38
+#define PADNUM_PER0_GPIO_B39 39
+#define PADNUM_PER0_GPIO_B40 40
+#define PADNUM_PER0_GPIO_B41 41
+#define PADNUM_PER0_GPIO_B42 42
+#define PADNUM_PER0_GPIO_B43 43
+#define PADNUM_PER0_GPIO_B44 44
+#define PADNUM_PER0_GPIO_B45 45
+#define PADNUM_PER0_GPIO_B46 46
+#define PADNUM_PER0_GPIO_B47 47
+#define PADNUM_PER0_GPIO_B48 48
+#define PADNUM_PER0_GPIO_B49 49
+#define PADNUM_PER0_GPIO_B50 50
+#define PADNUM_PER0_GPIO_B51 51
+#define PADNUM_PER0_GPIO_B52 52
+#define PADNUM_PER0_GPIO_B53 53
+#define PADNUM_PER0_GPIO_B54 54
+#define PADNUM_PER0_GPIO_B55 55
+#define PADNUM_PER0_GPIO_B56 56
+#define PADNUM_PER0_GPIO_B57 57
+#define PADNUM_PER0_GPIO_B58 58
+#define PADNUM_PER0_GPIO_B59 59
+
/* pinctrl hog power-source value */
#define JHB100_PINVREF_3_3V 0
#define JHB100_PINVREF_2_5V 1
--
2.25.1
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply related [flat|nested] 32+ messages in thread* Re: [PATCH v2 12/22] dt-bindings: pinctrl: Add starfive,jhb100-per0-pinctrl
2026-05-14 11:12 ` [PATCH v2 12/22] dt-bindings: pinctrl: Add starfive,jhb100-per0-pinctrl Changhuang Liang
@ 2026-05-14 13:17 ` Rob Herring (Arm)
0 siblings, 0 replies; 32+ messages in thread
From: Rob Herring (Arm) @ 2026-05-14 13:17 UTC (permalink / raw)
To: Changhuang Liang
Cc: Emil Renner Berthing, linux-gpio, linux-kernel, Lianfeng Ouyang,
Albert Ou, Palmer Dabbelt, Conor Dooley, Linus Walleij,
devicetree, linux-riscv, Bartosz Golaszewski, Paul Walmsley,
Alexandre Ghiti, Philipp Zabel, Krzysztof Kozlowski
On Thu, 14 May 2026 04:12:08 -0700, Changhuang Liang wrote:
> Add pinctrl bindings for StarFive JHB100 SoC Peripheral-0(per0) pinctrl
> controller.
>
> Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
> ---
> .../pinctrl/starfive,jhb100-per0-pinctrl.yaml | 176 ++++++++++++++++++
> .../pinctrl/starfive,jhb100-pinctrl.h | 62 ++++++
> 2 files changed, 238 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per0-pinctrl.yaml
>
My bot found errors running 'make dt_binding_check' on your patch:
yamllint warnings/errors:
./Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys2-pinctrl.yaml:135:14: [warning] wrong indentation: expected 12 but found 13 (indentation)
./Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys1-pinctrl.yaml:136:14: [warning] wrong indentation: expected 12 but found 13 (indentation)
./Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per0-pinctrl.yaml:136:14: [warning] wrong indentation: expected 12 but found 13 (indentation)
dtschema/dtc warnings/errors:
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per0-pinctrl.example.dtb: pinctrl@11a0a000 (starfive,jhb100-per0-pinctrl): gpio-ranges:2: [32, 28] is too short
from schema $id: http://devicetree.org/schemas/gpio/gpio.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys1-pinctrl.example.dtb: pinctrl@13081000 (starfive,jhb100-sys1-pinctrl): gpio-ranges:1: [8] is too short
from schema $id: http://devicetree.org/schemas/gpio/gpio.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys2-pinctrl.example.dtb: pinctrl@13082000 (starfive,jhb100-sys2-pinctrl): gpio-ranges:2: [32, 5] is too short
from schema $id: http://devicetree.org/schemas/gpio/gpio.yaml
doc reference errors (make refcheckdocs):
See https://patchwork.kernel.org/project/devicetree/patch/20260514111218.94519-13-changhuang.liang@starfivetech.com
The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.
If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:
pip3 install dtschema --upgrade
Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply [flat|nested] 32+ messages in thread
* [PATCH v2 13/22] pinctrl: starfive: Add StarFive JHB100 per0 controller driver
2026-05-14 11:11 [PATCH v2 00/22] Add basic pinctrl drivers for JHB100 SoC Changhuang Liang
` (11 preceding siblings ...)
2026-05-14 11:12 ` [PATCH v2 12/22] dt-bindings: pinctrl: Add starfive,jhb100-per0-pinctrl Changhuang Liang
@ 2026-05-14 11:12 ` Changhuang Liang
2026-05-14 11:12 ` [PATCH v2 14/22] dt-bindings: pinctrl: Add starfive,jhb100-per1-pinctrl Changhuang Liang
` (8 subsequent siblings)
21 siblings, 0 replies; 32+ messages in thread
From: Changhuang Liang @ 2026-05-14 11:12 UTC (permalink / raw)
To: Linus Walleij, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Emil Renner Berthing, Paul Walmsley, Albert Ou, Palmer Dabbelt,
Alexandre Ghiti, Philipp Zabel, Bartosz Golaszewski
Cc: linux-gpio, linux-kernel, devicetree, linux-riscv,
Lianfeng Ouyang, Changhuang Liang
Add pinctrl driver for StarFive JHB100 SoC Peripheral-0(per0) pinctrl
controller.
Co-developed-by: Lianfeng Ouyang <lianfeng.ouyang@starfivetech.com>
Signed-off-by: Lianfeng Ouyang <lianfeng.ouyang@starfivetech.com>
Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
---
drivers/pinctrl/starfive/Kconfig | 12 ++
drivers/pinctrl/starfive/Makefile | 1 +
.../starfive/pinctrl-starfive-jhb100-per0.c | 154 ++++++++++++++++++
3 files changed, 167 insertions(+)
create mode 100644 drivers/pinctrl/starfive/pinctrl-starfive-jhb100-per0.c
diff --git a/drivers/pinctrl/starfive/Kconfig b/drivers/pinctrl/starfive/Kconfig
index da11d486779a..1e1bfdf87c31 100644
--- a/drivers/pinctrl/starfive/Kconfig
+++ b/drivers/pinctrl/starfive/Kconfig
@@ -55,6 +55,18 @@ config PINCTRL_STARFIVE_JHB100
select GPIOLIB_IRQCHIP
select OF_GPIO
+config PINCTRL_STARFIVE_JHB100_PER0
+ tristate "StarFive JHB100 SoC Peripheral-0 pinctrl and GPIO driver"
+ depends on ARCH_STARFIVE || COMPILE_TEST
+ depends on OF
+ select PINCTRL_STARFIVE_JHB100
+ default ARCH_STARFIVE
+ help
+ Say yes here to support Peripheral-0 pin control on the StarFive JHB100 SoC.
+ This also provides an interface to the GPIO pins not used by other
+ peripherals supporting inputs, outputs, configuring pull-up/pull-down
+ and interrupts on input changes.
+
config PINCTRL_STARFIVE_JHB100_SYS0
tristate "StarFive JHB100 SoC System-0 pinctrl and GPIO driver"
depends on ARCH_STARFIVE || COMPILE_TEST
diff --git a/drivers/pinctrl/starfive/Makefile b/drivers/pinctrl/starfive/Makefile
index b817ad93b91d..f2bb0c35a2a0 100644
--- a/drivers/pinctrl/starfive/Makefile
+++ b/drivers/pinctrl/starfive/Makefile
@@ -7,6 +7,7 @@ obj-$(CONFIG_PINCTRL_STARFIVE_JH7110_SYS) += pinctrl-starfive-jh7110-sys.o
obj-$(CONFIG_PINCTRL_STARFIVE_JH7110_AON) += pinctrl-starfive-jh7110-aon.o
obj-$(CONFIG_PINCTRL_STARFIVE_JHB100) += pinctrl-starfive-jhb100.o
+obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_PER0) += pinctrl-starfive-jhb100-per0.o
obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_SYS0) += pinctrl-starfive-jhb100-sys0.o
obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_SYS0H) += pinctrl-starfive-jhb100-sys0h.o
obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_SYS1) += pinctrl-starfive-jhb100-sys1.o
diff --git a/drivers/pinctrl/starfive/pinctrl-starfive-jhb100-per0.c b/drivers/pinctrl/starfive/pinctrl-starfive-jhb100-per0.c
new file mode 100644
index 000000000000..3d8fe612b1bf
--- /dev/null
+++ b/drivers/pinctrl/starfive/pinctrl-starfive-jhb100-per0.c
@@ -0,0 +1,154 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Pinctrl / GPIO driver for StarFive JHB100 SoC Peripheral-0 domain
+ *
+ * Copyright (C) 2024 StarFive Technology Co., Ltd.
+ * Author: Alex Soo <yuklin.soo@starfivetech.com>
+ *
+ */
+
+#include <dt-bindings/pinctrl/starfive,jhb100-pinctrl.h>
+#include <linux/mod_devicetable.h>
+#include <linux/platform_device.h>
+
+#include "pinctrl-starfive-jhb100.h"
+
+static const struct jhb100_pin_layout_desc jhb100_per0_pl_desc[] = {
+ { .pin_start = 0, .pin_cnt = 60, .name = "gpio", .gpio_func_sel = 0 },
+ { 0xff },
+};
+
+static struct config_reg_layout_desc jhb100_per0_pinctrl_rl_desc[] = {
+ {
+ .pin_start = 0,
+ .pin_cnt = 60,
+ .input_enable = { .shift = 0, .width = 1 },
+ .mode_select = { .shift = 1, .width = 2 },
+ .pull_down = { .shift = 3, .width = 1 },
+ .pull_up = { .shift = 4, .width = 1 },
+ .open_drain_pull_up_sel = { .shift = 5, .width = 2 },
+ .schmitt_trigger_select = { .shift = 7, .width = 1 },
+ .reserved = { .shift = 8, .width = 7 },
+ .debounce_width = { .shift = 15, .width = 17 },
+ },
+ { 0xff },
+};
+
+static const struct pinvref_desc pinvref_desc_per0[] = {
+ {
+ .name = "gpioe-i3c0",
+ .pin_grp = {
+ PADNUM_PER0_GPIO_B8,
+ PADNUM_PER0_GPIO_B9,
+ PADNUM_PER0_GPIO_B10,
+ PADNUM_PER0_GPIO_B11,
+ PADNUM_PER0_GPIO_B32,
+ PADNUM_PER0_GPIO_B33
+ },
+ .num_pins = 6,
+ .range = BIT(JHB100_PINVREF_1_8V) | BIT(JHB100_PINVREF_3_3V)
+ },
+ {
+ .name = "gpioe-i3c1",
+ .pin_grp = {
+ PADNUM_PER0_GPIO_B12,
+ PADNUM_PER0_GPIO_B13,
+ PADNUM_PER0_GPIO_B14,
+ PADNUM_PER0_GPIO_B15,
+ PADNUM_PER0_GPIO_B34,
+ PADNUM_PER0_GPIO_B35
+ },
+ .num_pins = 6,
+ .range = BIT(JHB100_PINVREF_1_8V) | BIT(JHB100_PINVREF_3_3V)
+ },
+ {
+ .name = "gpioe-i3c2",
+ .pin_grp = {
+ PADNUM_PER0_GPIO_B16,
+ PADNUM_PER0_GPIO_B17,
+ PADNUM_PER0_GPIO_B18,
+ PADNUM_PER0_GPIO_B19,
+ PADNUM_PER0_GPIO_B20,
+ PADNUM_PER0_GPIO_B21,
+ PADNUM_PER0_GPIO_B22,
+ PADNUM_PER0_GPIO_B23
+ },
+ .num_pins = 8,
+ .range = BIT(JHB100_PINVREF_1_8V) | BIT(JHB100_PINVREF_3_3V)
+ },
+ {
+ .name = "gpioe-i3c4",
+ .pin_grp = {
+ PADNUM_PER0_GPIO_B36,
+ PADNUM_PER0_GPIO_B37,
+ PADNUM_PER0_GPIO_B38,
+ PADNUM_PER0_GPIO_B39,
+ PADNUM_PER0_GPIO_B40,
+ PADNUM_PER0_GPIO_B41,
+ PADNUM_PER0_GPIO_B42,
+ PADNUM_PER0_GPIO_B43
+ },
+ .num_pins = 8,
+ .range = BIT(JHB100_PINVREF_1_8V) | BIT(JHB100_PINVREF_3_3V)
+ },
+ { NULL },
+};
+
+struct starfive_pinctrl_regs jhb100_per0_pinctrl_regs = {
+ .vref = { .reg = 0x004, .pv_desc = pinvref_desc_per0 },
+ .func_sel = { .reg = 0x11c, .width_per_pin = 2 },
+ .config = 0x014,
+ .output = 0x104,
+ .output_en = 0x10c,
+ .gpio_status = 0x114,
+ .irq_en = 0x12c,
+ .irq_status = 0x134,
+ .irq_clr = 0x13c,
+ .irq_trigger = 0x144,
+ .irq_level = 0x14c,
+ .irq_both_edge = 0x154,
+ .irq_edge = 0x15c,
+};
+
+static const struct jhb100_pinctrl_func_maps jhb100_func_maps_per0[] = {
+ { .func = "gmac_mdio", .val = 2 },
+ { .func = "gpio", .val = 0 },
+ { .func = "i2c", .val = 1 },
+ { .func = "i3c", .val = 2,
+ .max_pin = JHB100_FUNC_MAPS_MAX_PIN(PADNUM_PER0_GPIO_B23) },
+ { .func = "i3c", .val = 1,
+ .max_pin = JHB100_FUNC_MAPS_MAX_PIN(PADNUM_PER0_GPIO_B59) },
+ { .func = "smbalert", .val = 1 },
+ { .func = "wdt", .val = 2 },
+};
+
+static const struct jhb100_pinctrl_domain_info jhb100_per0_pinctrl_info = {
+ .name = "jhb100-per0",
+ .pl_desc = jhb100_per0_pl_desc,
+ .crl_desc = jhb100_per0_pinctrl_rl_desc,
+ .regs = &jhb100_per0_pinctrl_regs,
+ .fmaps = jhb100_func_maps_per0,
+ .num_maps = ARRAY_SIZE(jhb100_func_maps_per0),
+};
+
+static const struct of_device_id jhb100_per0_pinctrl_of_match[] = {
+ {
+ .compatible = "starfive,jhb100-per0-pinctrl",
+ .data = &jhb100_per0_pinctrl_info,
+ },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, jhb100_per0_pinctrl_of_match);
+
+static struct platform_driver jhb100_per0_pinctrl_driver = {
+ .probe = jhb100_pinctrl_probe,
+ .driver = {
+ .name = "starfive-jhb100-per0-pinctrl",
+ .of_match_table = jhb100_per0_pinctrl_of_match,
+ },
+};
+module_platform_driver(jhb100_per0_pinctrl_driver);
+
+MODULE_DESCRIPTION("Pinctrl driver for StarFive JHB100 SoC Peripheral-0 domain");
+MODULE_AUTHOR("Alex Soo <yuklin.soo@starfivetech.com>");
+MODULE_LICENSE("GPL");
--
2.25.1
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply related [flat|nested] 32+ messages in thread* [PATCH v2 14/22] dt-bindings: pinctrl: Add starfive,jhb100-per1-pinctrl
2026-05-14 11:11 [PATCH v2 00/22] Add basic pinctrl drivers for JHB100 SoC Changhuang Liang
` (12 preceding siblings ...)
2026-05-14 11:12 ` [PATCH v2 13/22] pinctrl: starfive: Add StarFive JHB100 per0 controller driver Changhuang Liang
@ 2026-05-14 11:12 ` Changhuang Liang
2026-05-14 13:17 ` Rob Herring (Arm)
2026-05-14 11:12 ` [PATCH v2 15/22] pinctrl: starfive: Add StarFive JHB100 per1 controller driver Changhuang Liang
` (7 subsequent siblings)
21 siblings, 1 reply; 32+ messages in thread
From: Changhuang Liang @ 2026-05-14 11:12 UTC (permalink / raw)
To: Linus Walleij, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Emil Renner Berthing, Paul Walmsley, Albert Ou, Palmer Dabbelt,
Alexandre Ghiti, Philipp Zabel, Bartosz Golaszewski
Cc: linux-gpio, linux-kernel, devicetree, linux-riscv,
Lianfeng Ouyang, Changhuang Liang
Add pinctrl bindings for StarFive JHB100 SoC Peripheral-1(per1) pinctrl
controller.
Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
---
.../pinctrl/starfive,jhb100-per1-pinctrl.yaml | 175 ++++++++++++++++++
.../pinctrl/starfive,jhb100-pinctrl.h | 38 ++++
2 files changed, 213 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per1-pinctrl.yaml
diff --git a/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per1-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per1-pinctrl.yaml
new file mode 100644
index 000000000000..c97dbf674975
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per1-pinctrl.yaml
@@ -0,0 +1,175 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/starfive,jhb100-per1-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: StarFive JHB100 Peripheral-1 Pin Controller
+
+description: |
+ Pinctrl bindings for JHB100 RISC-V SoC from StarFive Technology Ltd.
+
+ The JHB100 SoC has 13 pinctrl domains - sys0, sys0h, sys1, sys2, per0, per1,
+ per2, per2pok, per3, adc0, adc1, emmc, and vga.
+ This document provides an overview of the "per1" pinctrl domain.
+
+ The "per1" domain has a pin controller which provides
+ - function selection for GPIO pads.
+ - GPIO pad configuration.
+ - GPIO interrupt handling.
+
+ In the Peripheral-1 Pin Controller, there are 36 multi-function GPIO_PADs.
+ Each of them can be multiplexed to several peripherals through function
+ selection. Each iopad has a maximum of up to 3 functions - 0, 1, and 2.
+ Function 0 is the default function which is generally the GPIO function.
+ Function 1 and 2 are the alternate functions or peripheral signals that
+ can be routed to the iopad. The function selection can be carried out by
+ writing the function number to the iopad function select register.
+
+ Each iopad is configurable with parameters such as input-enable, internal
+ pull-up/pull-down bias, drive strength, schmitt trigger, slew rate, input
+ debounce nanoseconds, power source and drive type (open-drain or push-pull).
+
+maintainers:
+ - Alex Soo <yuklin.soo@starfivetech.com>
+
+properties:
+ compatible:
+ items:
+ - const: starfive,jhb100-per1-pinctrl
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ resets:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ interrupt-controller: true
+
+ '#interrupt-cells':
+ const: 3
+
+ gpio-controller: true
+
+ '#gpio-cells':
+ const: 3
+
+ gpio-ranges: true
+
+ gpio-line-names: true
+
+patternProperties:
+ '-grp$':
+ type: object
+ additionalProperties: false
+ patternProperties:
+ '-pins$':
+ type: object
+ description: |
+ A pinctrl node should contain at least one subnode representing the
+ pinctrl groups available in the domain. Each subnode will list the
+ pins it needs, and how they should be configured, with regard to
+ function selection, bias, input enable/disable, input schmitt
+ trigger enable/disable, slew-rate, input debounce nanoseconds,
+ drive-open-drain, drive-push-pull, power-source and drive-strength.
+ allOf:
+ - $ref: /schemas/pinctrl/pincfg-node.yaml
+ - $ref: /schemas/pinctrl/pinmux-node.yaml
+ unevaluatedProperties: false
+
+ properties:
+ pins:
+ description:
+ The list of IOs that properties in the pincfg node apply to.
+
+ function:
+ description:
+ A string containing the name of the function to mux for these
+ pins.
+ enum: [ gpio, i2c, sfc, sgpio, spi ]
+
+ bias-disable: true
+
+ bias-pull-down:
+ type: boolean
+
+ bias-pull-up:
+ oneOf:
+ - type: boolean
+ - enum: [ 600, 900, 1200, 2000 ]
+ description: Pull up RSEL type resistance values (in ohms)
+ description:
+ For normal pull up type there is no need to specify a resistance
+ value, hence this can be specified as a boolean property.
+ For RSEL pull up type a resistance value (in ohms) can be added.
+
+ drive-open-drain: true
+
+ drive-push-pull: true
+
+ drive-strength:
+ enum: [ 2, 4, 8, 12 ]
+
+ drive-strength-microamp:
+ enum: [ 2000, 4000, 8000, 12000 ]
+
+ input-debounce-nanoseconds:
+ minimum: 0
+ maximum: 4294967295
+
+ input-disable: true
+
+ input-enable: true
+
+ input-schmitt-enable: true
+
+ input-schmitt-disable: true
+
+ power-source:
+ enum: [ 0, 1, 2 ]
+
+ slew-rate:
+ enum: [ 0, 1 ]
+ default: 0
+ description: |
+ 0: slow (half frequency)
+ 1: fast
+
+required:
+ - compatible
+ - reg
+ - resets
+ - interrupts
+ - interrupt-controller
+ - '#interrupt-cells'
+ - gpio-controller
+ - '#gpio-cells'
+ - gpio-ranges
+
+additionalProperties: false
+
+examples:
+ - |
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ pinctrl_per1: pinctrl@11b42000 {
+ compatible = "starfive,jhb100-per1-pinctrl";
+ reg = <0x0 0x11b42000 0x0 0x800>;
+ resets = <&per1crg 0>;
+ interrupts = <61>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ gpio-ranges = <&pinctrl_per1 0 0 0 32>,
+ <&pinctrl_per1 1 0 32 4>;
+ };
+ };
diff --git a/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h b/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h
index 0a8494b577e0..ab3b678dfd4b 100644
--- a/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h
+++ b/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h
@@ -139,6 +139,44 @@
#define PADNUM_PER0_GPIO_B58 58
#define PADNUM_PER0_GPIO_B59 59
+/* per1 pad numbers */
+#define PADNUM_PER1_GPIO_C0 0
+#define PADNUM_PER1_GPIO_C1 1
+#define PADNUM_PER1_GPIO_C2 2
+#define PADNUM_PER1_GPIO_C3 3
+#define PADNUM_PER1_GPIO_C4 4
+#define PADNUM_PER1_GPIO_C5 5
+#define PADNUM_PER1_GPIO_C6 6
+#define PADNUM_PER1_GPIO_C7 7
+#define PADNUM_PER1_GPIO_C8 8
+#define PADNUM_PER1_GPIO_C9 9
+#define PADNUM_PER1_GPIO_C10 10
+#define PADNUM_PER1_GPIO_C11 11
+#define PADNUM_PER1_GPIO_C12 12
+#define PADNUM_PER1_GPIO_C13 13
+#define PADNUM_PER1_GPIO_C14 14
+#define PADNUM_PER1_GPIO_C15 15
+#define PADNUM_PER1_GPIO_C16 16
+#define PADNUM_PER1_GPIO_C17 17
+#define PADNUM_PER1_GPIO_C18 18
+#define PADNUM_PER1_GPIO_C19 19
+#define PADNUM_PER1_GPIO_C20 20
+#define PADNUM_PER1_GPIO_C21 21
+#define PADNUM_PER1_GPIO_C22 22
+#define PADNUM_PER1_GPIO_C23 23
+#define PADNUM_PER1_GPIO_C24 24
+#define PADNUM_PER1_GPIO_C25 25
+#define PADNUM_PER1_GPIO_C26 26
+#define PADNUM_PER1_GPIO_C27 27
+#define PADNUM_PER1_GPIO_C28 28
+#define PADNUM_PER1_GPIO_C29 29
+#define PADNUM_PER1_GPIO_C30 30
+#define PADNUM_PER1_GPIO_C31 31
+#define PADNUM_PER1_GPIO_C32 32
+#define PADNUM_PER1_GPIO_C33 33
+#define PADNUM_PER1_GPIO_C34 34
+#define PADNUM_PER1_GPIO_C35 35
+
/* pinctrl hog power-source value */
#define JHB100_PINVREF_3_3V 0
#define JHB100_PINVREF_2_5V 1
--
2.25.1
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply related [flat|nested] 32+ messages in thread* Re: [PATCH v2 14/22] dt-bindings: pinctrl: Add starfive,jhb100-per1-pinctrl
2026-05-14 11:12 ` [PATCH v2 14/22] dt-bindings: pinctrl: Add starfive,jhb100-per1-pinctrl Changhuang Liang
@ 2026-05-14 13:17 ` Rob Herring (Arm)
0 siblings, 0 replies; 32+ messages in thread
From: Rob Herring (Arm) @ 2026-05-14 13:17 UTC (permalink / raw)
To: Changhuang Liang
Cc: Emil Renner Berthing, Conor Dooley, devicetree,
Krzysztof Kozlowski, linux-kernel, Alexandre Ghiti,
Lianfeng Ouyang, Paul Walmsley, linux-gpio, Palmer Dabbelt,
Linus Walleij, Albert Ou, Philipp Zabel, Bartosz Golaszewski,
linux-riscv
On Thu, 14 May 2026 04:12:10 -0700, Changhuang Liang wrote:
> Add pinctrl bindings for StarFive JHB100 SoC Peripheral-1(per1) pinctrl
> controller.
>
> Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
> ---
> .../pinctrl/starfive,jhb100-per1-pinctrl.yaml | 175 ++++++++++++++++++
> .../pinctrl/starfive,jhb100-pinctrl.h | 38 ++++
> 2 files changed, 213 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per1-pinctrl.yaml
>
My bot found errors running 'make dt_binding_check' on your patch:
yamllint warnings/errors:
./Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per1-pinctrl.yaml:135:14: [warning] wrong indentation: expected 12 but found 13 (indentation)
dtschema/dtc warnings/errors:
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per1-pinctrl.example.dtb: pinctrl@11b42000 (starfive,jhb100-per1-pinctrl): gpio-ranges:2: [32, 4] is too short
from schema $id: http://devicetree.org/schemas/gpio/gpio.yaml
doc reference errors (make refcheckdocs):
See https://patchwork.kernel.org/project/devicetree/patch/20260514111218.94519-15-changhuang.liang@starfivetech.com
The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.
If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:
pip3 install dtschema --upgrade
Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply [flat|nested] 32+ messages in thread
* [PATCH v2 15/22] pinctrl: starfive: Add StarFive JHB100 per1 controller driver
2026-05-14 11:11 [PATCH v2 00/22] Add basic pinctrl drivers for JHB100 SoC Changhuang Liang
` (13 preceding siblings ...)
2026-05-14 11:12 ` [PATCH v2 14/22] dt-bindings: pinctrl: Add starfive,jhb100-per1-pinctrl Changhuang Liang
@ 2026-05-14 11:12 ` Changhuang Liang
2026-05-14 11:12 ` [PATCH v2 16/22] dt-bindings: pinctrl: Add starfive,jhb100-per2-pinctrl Changhuang Liang
` (6 subsequent siblings)
21 siblings, 0 replies; 32+ messages in thread
From: Changhuang Liang @ 2026-05-14 11:12 UTC (permalink / raw)
To: Linus Walleij, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Emil Renner Berthing, Paul Walmsley, Albert Ou, Palmer Dabbelt,
Alexandre Ghiti, Philipp Zabel, Bartosz Golaszewski
Cc: linux-gpio, linux-kernel, devicetree, linux-riscv,
Lianfeng Ouyang, Changhuang Liang
Add pinctrl driver for StarFive JHB100 SoC Peripheral-1(per1) pinctrl
controller.
Co-developed-by: Lianfeng Ouyang <lianfeng.ouyang@starfivetech.com>
Signed-off-by: Lianfeng Ouyang <lianfeng.ouyang@starfivetech.com>
Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
---
drivers/pinctrl/starfive/Kconfig | 12 ++
drivers/pinctrl/starfive/Makefile | 1 +
.../starfive/pinctrl-starfive-jhb100-per1.c | 165 ++++++++++++++++++
3 files changed, 178 insertions(+)
create mode 100644 drivers/pinctrl/starfive/pinctrl-starfive-jhb100-per1.c
diff --git a/drivers/pinctrl/starfive/Kconfig b/drivers/pinctrl/starfive/Kconfig
index 1e1bfdf87c31..c3889a152f6c 100644
--- a/drivers/pinctrl/starfive/Kconfig
+++ b/drivers/pinctrl/starfive/Kconfig
@@ -67,6 +67,18 @@ config PINCTRL_STARFIVE_JHB100_PER0
peripherals supporting inputs, outputs, configuring pull-up/pull-down
and interrupts on input changes.
+config PINCTRL_STARFIVE_JHB100_PER1
+ tristate "StarFive JHB100 SoC Peripheral-1 pinctrl and GPIO driver"
+ depends on ARCH_STARFIVE || COMPILE_TEST
+ depends on OF
+ select PINCTRL_STARFIVE_JHB100
+ default ARCH_STARFIVE
+ help
+ Say yes here to support Peripheral-1 pin control on the StarFive JHB100 SoC.
+ This also provides an interface to the GPIO pins not used by other
+ peripherals supporting inputs, outputs, configuring pull-up/pull-down
+ and interrupts on input changes.
+
config PINCTRL_STARFIVE_JHB100_SYS0
tristate "StarFive JHB100 SoC System-0 pinctrl and GPIO driver"
depends on ARCH_STARFIVE || COMPILE_TEST
diff --git a/drivers/pinctrl/starfive/Makefile b/drivers/pinctrl/starfive/Makefile
index f2bb0c35a2a0..6beef7e313ef 100644
--- a/drivers/pinctrl/starfive/Makefile
+++ b/drivers/pinctrl/starfive/Makefile
@@ -8,6 +8,7 @@ obj-$(CONFIG_PINCTRL_STARFIVE_JH7110_AON) += pinctrl-starfive-jh7110-aon.o
obj-$(CONFIG_PINCTRL_STARFIVE_JHB100) += pinctrl-starfive-jhb100.o
obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_PER0) += pinctrl-starfive-jhb100-per0.o
+obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_PER1) += pinctrl-starfive-jhb100-per1.o
obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_SYS0) += pinctrl-starfive-jhb100-sys0.o
obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_SYS0H) += pinctrl-starfive-jhb100-sys0h.o
obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_SYS1) += pinctrl-starfive-jhb100-sys1.o
diff --git a/drivers/pinctrl/starfive/pinctrl-starfive-jhb100-per1.c b/drivers/pinctrl/starfive/pinctrl-starfive-jhb100-per1.c
new file mode 100644
index 000000000000..91dfa113ca06
--- /dev/null
+++ b/drivers/pinctrl/starfive/pinctrl-starfive-jhb100-per1.c
@@ -0,0 +1,165 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Pinctrl / GPIO driver for StarFive JHB100 SoC Peripheral-1 domain
+ *
+ * Copyright (C) 2024 StarFive Technology Co., Ltd.
+ * Author: Alex Soo <yuklin.soo@starfivetech.com>
+ *
+ */
+
+#include <dt-bindings/pinctrl/starfive,jhb100-pinctrl.h>
+#include <linux/mod_devicetable.h>
+#include <linux/platform_device.h>
+
+#include "pinctrl-starfive-jhb100.h"
+
+static const struct jhb100_pin_layout_desc jhb100_per1_pl_desc[] = {
+ { .pin_start = 0, .pin_cnt = 36, .name = "gpio", .gpio_func_sel = 0 },
+ { 0xff },
+};
+
+static struct config_reg_layout_desc jhb100_per1_pinctr_rldesc[] = {
+ {
+ .pin_start = 0,
+ .pin_cnt = 32,
+ .drive_strength_2bit = { .shift = 0, .width = 2 },
+ .input_enable = { .shift = 2, .width = 1 },
+ .pull_down = { .shift = 3, .width = 1 },
+ .pull_up = { .shift = 4, .width = 1 },
+ .slew_rate = { .shift = 5, .width = 1 },
+ .schmitt_trigger_select = { .shift = 6, .width = 1 },
+ .reserved = { .shift = 7, .width = 8 },
+ .debounce_width = { .shift = 15, .width = 17 },
+ },
+ {
+ .pin_start = 32,
+ .pin_cnt = 4,
+ .input_enable = { .shift = 0, .width = 1 },
+ .mode_select = { .shift = 1, .width = 2 },
+ .pull_down = { .shift = 3, .width = 1 },
+ .pull_up = { .shift = 4, .width = 1 },
+ .open_drain_pull_up_sel = { .shift = 5, .width = 2 },
+ .schmitt_trigger_select = { .shift = 7, .width = 1 },
+ .reserved = { .shift = 8, .width = 7 },
+ .debounce_width = { .shift = 15, .width = 17 },
+ },
+ { 0xff },
+};
+
+static const struct pinvref_desc pinvref_desc_per1[] = {
+ {
+ .name = "gpioe-spi",
+ .pin_grp = {
+ PADNUM_PER1_GPIO_C0,
+ PADNUM_PER1_GPIO_C1,
+ PADNUM_PER1_GPIO_C2,
+ PADNUM_PER1_GPIO_C3,
+ PADNUM_PER1_GPIO_C4
+ },
+ .num_pins = 5,
+ .range = BIT(JHB100_PINVREF_1_8V) | BIT(JHB100_PINVREF_3_3V)
+ },
+ {
+ .name = "gpioe-qspi0",
+ .pin_grp = {
+ PADNUM_PER1_GPIO_C5,
+ PADNUM_PER1_GPIO_C6,
+ PADNUM_PER1_GPIO_C7,
+ PADNUM_PER1_GPIO_C8,
+ PADNUM_PER1_GPIO_C9,
+ PADNUM_PER1_GPIO_C10,
+ PADNUM_PER1_GPIO_C11
+ },
+ .num_pins = 7,
+ .range = BIT(JHB100_PINVREF_1_8V) | BIT(JHB100_PINVREF_3_3V)
+ },
+ {
+ .name = "gpioe-qspi1",
+ .pin_grp = {
+ PADNUM_PER1_GPIO_C12,
+ PADNUM_PER1_GPIO_C13,
+ PADNUM_PER1_GPIO_C14,
+ PADNUM_PER1_GPIO_C15,
+ PADNUM_PER1_GPIO_C16,
+ PADNUM_PER1_GPIO_C17,
+ PADNUM_PER1_GPIO_C18,
+ PADNUM_PER1_GPIO_C19
+ },
+ .num_pins = 8,
+ .range = BIT(JHB100_PINVREF_1_8V) | BIT(JHB100_PINVREF_3_3V)
+ },
+ {
+ .name = "gpioe-qspi2",
+ .pin_grp = {
+ PADNUM_PER1_GPIO_C20,
+ PADNUM_PER1_GPIO_C21,
+ PADNUM_PER1_GPIO_C22,
+ PADNUM_PER1_GPIO_C23,
+ PADNUM_PER1_GPIO_C24,
+ PADNUM_PER1_GPIO_C25,
+ PADNUM_PER1_GPIO_C26,
+ PADNUM_PER1_GPIO_C27
+ },
+ .num_pins = 8,
+ .range = BIT(JHB100_PINVREF_1_8V) | BIT(JHB100_PINVREF_3_3V)
+ },
+ { NULL },
+};
+
+struct starfive_pinctrl_regs jhb100_per1_pinctrl_regs = {
+ .vref = { .reg = 0x00, .pv_desc = pinvref_desc_per1 },
+ .func_sel = { .reg = 0xbc, .width_per_pin = 2 },
+ .config = 0x14,
+ .output = 0xa4,
+ .output_en = 0xac,
+ .gpio_status = 0xb4,
+ .irq_en = 0xc8,
+ .irq_status = 0xd0,
+ .irq_clr = 0xd8,
+ .irq_trigger = 0xe0,
+ .irq_level = 0xe8,
+ .irq_both_edge = 0xf0,
+ .irq_edge = 0xf8,
+};
+
+static const struct jhb100_pinctrl_func_maps jhb100_func_maps_per1[] = {
+ { .func = "gpio", .val = 0 },
+ { .func = "i2c", .val = 1 },
+ { .func = "sfc", .val = 1 },
+ { .func = "sgpio", .val = 1,
+ .max_pin = JHB100_FUNC_MAPS_MAX_PIN(PADNUM_PER1_GPIO_C31) },
+ { .func = "sgpio", .val = 2,
+ .max_pin = JHB100_FUNC_MAPS_MAX_PIN(PADNUM_PER1_GPIO_C35) },
+ { .func = "spi", .val = 1 },
+};
+
+static const struct jhb100_pinctrl_domain_info jhb100_per1_pinctrl_info = {
+ .name = "jhb100-per1",
+ .pl_desc = jhb100_per1_pl_desc,
+ .crl_desc = jhb100_per1_pinctr_rldesc,
+ .regs = &jhb100_per1_pinctrl_regs,
+ .fmaps = jhb100_func_maps_per1,
+ .num_maps = ARRAY_SIZE(jhb100_func_maps_per1),
+};
+
+static const struct of_device_id jhb100_per1_pinctrl_of_match[] = {
+ {
+ .compatible = "starfive,jhb100-per1-pinctrl",
+ .data = &jhb100_per1_pinctrl_info,
+ },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, jhb100_per1_pinctrl_of_match);
+
+static struct platform_driver jhb100_per1_pinctrl_driver = {
+ .probe = jhb100_pinctrl_probe,
+ .driver = {
+ .name = "starfive-jhb100-per1-pinctrl",
+ .of_match_table = jhb100_per1_pinctrl_of_match,
+ },
+};
+module_platform_driver(jhb100_per1_pinctrl_driver);
+
+MODULE_DESCRIPTION("Pinctrl driver for StarFive JHB100 SoC Peripheral-1 domain");
+MODULE_AUTHOR("Alex Soo <yuklin.soo@starfivetech.com>");
+MODULE_LICENSE("GPL");
--
2.25.1
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply related [flat|nested] 32+ messages in thread* [PATCH v2 16/22] dt-bindings: pinctrl: Add starfive,jhb100-per2-pinctrl
2026-05-14 11:11 [PATCH v2 00/22] Add basic pinctrl drivers for JHB100 SoC Changhuang Liang
` (14 preceding siblings ...)
2026-05-14 11:12 ` [PATCH v2 15/22] pinctrl: starfive: Add StarFive JHB100 per1 controller driver Changhuang Liang
@ 2026-05-14 11:12 ` Changhuang Liang
2026-05-14 11:12 ` [PATCH v2 17/22] pinctrl: starfive: Add StarFive JHB100 per2 controller driver Changhuang Liang
` (5 subsequent siblings)
21 siblings, 0 replies; 32+ messages in thread
From: Changhuang Liang @ 2026-05-14 11:12 UTC (permalink / raw)
To: Linus Walleij, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Emil Renner Berthing, Paul Walmsley, Albert Ou, Palmer Dabbelt,
Alexandre Ghiti, Philipp Zabel, Bartosz Golaszewski
Cc: linux-gpio, linux-kernel, devicetree, linux-riscv,
Lianfeng Ouyang, Changhuang Liang
Add pinctrl bindings for StarFive JHB100 SoC Peripheral-2(per2) pinctrl
controller.
Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
---
.../pinctrl/starfive,jhb100-per2-pinctrl.yaml | 175 ++++++++++++++++++
.../pinctrl/starfive,jhb100-pinctrl.h | 33 ++++
2 files changed, 208 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per2-pinctrl.yaml
diff --git a/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per2-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per2-pinctrl.yaml
new file mode 100644
index 000000000000..86684fed69d5
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per2-pinctrl.yaml
@@ -0,0 +1,175 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/starfive,jhb100-per2-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: StarFive JHB100 Peripheral-2 Pin Controller
+
+description: |
+ Pinctrl bindings for JHB100 RISC-V SoC from StarFive Technology Ltd.
+
+ The JHB100 SoC has 13 pinctrl domains - sys0, sys0h, sys1, sys2, per0, per1,
+ per2, per2pok, per3, adc0, adc1, emmc, and vga.
+ This document provides an overview of the "per2" pinctrl domain.
+
+ The "per2" domain has a pin controller which provides
+ - function selection for GPIO pads.
+ - GPIO pad configuration.
+ - GPIO interrupt handling.
+
+ In the Peripheral-2 Pin Controller, there are 31 multi-function GPIO_PADs.
+ Each of them can be multiplexed to several peripherals through function
+ selection. Each iopad has a maximum of up to 4 functions - 0, 1, 2, and 3.
+ Function 0 is the default function which is generally the GPIO function.
+ Function 1, 2, and 3 are the alternate functions or peripheral signals
+ that can be routed to an iopad. The function selection can be carried
+ out by writing the function number to the iopad function select register.
+
+ Each iopad is configurable with parameters such as input-enable, internal
+ pull-up/pull-down bias, drive strength, schmitt trigger, slew rate, input
+ debounce nanoseconds, power source and drive type (open-drain or push-pull).
+
+maintainers:
+ - Alex Soo <yuklin.soo@starfivetech.com>
+
+properties:
+ compatible:
+ items:
+ - const: starfive,jhb100-per2-pinctrl
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ resets:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ interrupt-controller: true
+
+ '#interrupt-cells':
+ const: 3
+
+ gpio-controller: true
+
+ '#gpio-cells':
+ const: 3
+
+ gpio-ranges: true
+
+ gpio-line-names: true
+
+patternProperties:
+ '-grp$':
+ type: object
+ additionalProperties: false
+ patternProperties:
+ '-pins$':
+ type: object
+ description: |
+ A pinctrl node should contain at least one subnode representing the
+ pinctrl groups available in the domain. Each subnode will list the
+ pins it needs, and how they should be configured, with regard to
+ function selection, bias, input enable/disable, input schmitt
+ trigger enable/disable, slew-rate, input debounce nanoseconds,
+ drive-open-drain, drive-push-pull, power-source and drive-strength.
+ allOf:
+ - $ref: /schemas/pinctrl/pincfg-node.yaml
+ - $ref: /schemas/pinctrl/pinmux-node.yaml
+ unevaluatedProperties: false
+
+ properties:
+ pins:
+ description:
+ The list of IOs that properties in the pincfg node apply to.
+
+ function:
+ description:
+ A string containing the name of the function to mux for these
+ pins.
+ enum: [ fan_tach, gmac_rgmii, gmac_rmii, gpio, host0_port80,
+ host1_port80 ]
+
+ bias-disable: true
+
+ bias-pull-down:
+ type: boolean
+
+ bias-pull-up:
+ oneOf:
+ - type: boolean
+ - enum: [ 600, 900, 1200, 2000 ]
+ description: Pull up RSEL type resistance values (in ohms)
+ description:
+ For normal pull up type there is no need to specify a resistance
+ value, hence this can be specified as a boolean property.
+ For RSEL pull up type a resistance value (in ohms) can be added.
+
+ drive-open-drain: true
+
+ drive-push-pull: true
+
+ drive-strength:
+ enum: [ 2, 4, 8, 12 ]
+
+ drive-strength-microamp:
+ enum: [ 2000, 4000, 8000, 12000 ]
+
+ input-debounce-nanoseconds:
+ minimum: 0
+ maximum: 4294967295
+
+ input-disable: true
+
+ input-enable: true
+
+ input-schmitt-enable: true
+
+ input-schmitt-disable: true
+
+ power-source:
+ enum: [ 0, 1, 2 ]
+
+ slew-rate:
+ enum: [ 0, 1 ]
+ default: 0
+ description: |
+ 0: slow (half frequency)
+ 1: fast
+
+required:
+ - compatible
+ - reg
+ - resets
+ - interrupts
+ - interrupt-controller
+ - '#interrupt-cells'
+ - gpio-controller
+ - '#gpio-cells'
+ - gpio-ranges
+
+additionalProperties: false
+
+examples:
+ - |
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ pinctrl_per2: pinctrl@11bc2000 {
+ compatible = "starfive,jhb100-per2-pinctrl";
+ reg = <0x0 0x11bc2000 0x0 0x400>;
+ resets = <&per2crg 0>;
+ interrupts = <62>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ gpio-ranges = <&pinctrl_per2 0 0 0 31>;
+ };
+ };
diff --git a/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h b/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h
index ab3b678dfd4b..6a80c56304e8 100644
--- a/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h
+++ b/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h
@@ -177,6 +177,39 @@
#define PADNUM_PER1_GPIO_C34 34
#define PADNUM_PER1_GPIO_C35 35
+/* per2 pad numbers */
+#define PADNUM_PER2_GPIO_D0 0
+#define PADNUM_PER2_GPIO_D1 1
+#define PADNUM_PER2_GPIO_D2 2
+#define PADNUM_PER2_GPIO_D3 3
+#define PADNUM_PER2_GPIO_D4 4
+#define PADNUM_PER2_GPIO_D5 5
+#define PADNUM_PER2_GPIO_D6 6
+#define PADNUM_PER2_GPIO_D7 7
+#define PADNUM_PER2_GPIO_D8 8
+#define PADNUM_PER2_GPIO_D9 9
+#define PADNUM_PER2_GPIO_D10 10
+#define PADNUM_PER2_GPIO_D11 11
+#define PADNUM_PER2_GPIO_D12 12
+#define PADNUM_PER2_GPIO_D13 13
+#define PADNUM_PER2_GPIO_D14 14
+#define PADNUM_PER2_GPIO_D15 15
+#define PADNUM_PER2_GPIO_D16 16
+#define PADNUM_PER2_GPIO_D17 17
+#define PADNUM_PER2_GPIO_D18 18
+#define PADNUM_PER2_GPIO_D19 19
+#define PADNUM_PER2_GPIO_D20 20
+#define PADNUM_PER2_GPIO_D21 21
+#define PADNUM_PER2_GPIO_D22 22
+#define PADNUM_PER2_GPIO_D23 23
+#define PADNUM_PER2_GPIO_D24 24
+#define PADNUM_PER2_GPIO_D25 25
+#define PADNUM_PER2_GPIO_D26 26
+#define PADNUM_PER2_GPIO_D27 27
+#define PADNUM_PER2_GPIO_D28 28
+#define PADNUM_PER2_GPIO_D29 29
+#define PADNUM_PER2_GPIO_D30 30
+
/* pinctrl hog power-source value */
#define JHB100_PINVREF_3_3V 0
#define JHB100_PINVREF_2_5V 1
--
2.25.1
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply related [flat|nested] 32+ messages in thread* [PATCH v2 17/22] pinctrl: starfive: Add StarFive JHB100 per2 controller driver
2026-05-14 11:11 [PATCH v2 00/22] Add basic pinctrl drivers for JHB100 SoC Changhuang Liang
` (15 preceding siblings ...)
2026-05-14 11:12 ` [PATCH v2 16/22] dt-bindings: pinctrl: Add starfive,jhb100-per2-pinctrl Changhuang Liang
@ 2026-05-14 11:12 ` Changhuang Liang
2026-05-14 11:12 ` [PATCH v2 18/22] dt-bindings: pinctrl: Add starfive,jhb100-per2pok-pinctrl Changhuang Liang
` (4 subsequent siblings)
21 siblings, 0 replies; 32+ messages in thread
From: Changhuang Liang @ 2026-05-14 11:12 UTC (permalink / raw)
To: Linus Walleij, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Emil Renner Berthing, Paul Walmsley, Albert Ou, Palmer Dabbelt,
Alexandre Ghiti, Philipp Zabel, Bartosz Golaszewski
Cc: linux-gpio, linux-kernel, devicetree, linux-riscv,
Lianfeng Ouyang, Changhuang Liang
Add pinctrl driver for StarFive JHB100 SoC Peripheral-2(per2) pinctrl
controller.
Co-developed-by: Lianfeng Ouyang <lianfeng.ouyang@starfivetech.com>
Signed-off-by: Lianfeng Ouyang <lianfeng.ouyang@starfivetech.com>
Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
---
drivers/pinctrl/starfive/Kconfig | 12 ++
drivers/pinctrl/starfive/Makefile | 1 +
.../starfive/pinctrl-starfive-jhb100-per2.c | 126 ++++++++++++++++++
3 files changed, 139 insertions(+)
create mode 100644 drivers/pinctrl/starfive/pinctrl-starfive-jhb100-per2.c
diff --git a/drivers/pinctrl/starfive/Kconfig b/drivers/pinctrl/starfive/Kconfig
index c3889a152f6c..edc3b6d9c8d7 100644
--- a/drivers/pinctrl/starfive/Kconfig
+++ b/drivers/pinctrl/starfive/Kconfig
@@ -79,6 +79,18 @@ config PINCTRL_STARFIVE_JHB100_PER1
peripherals supporting inputs, outputs, configuring pull-up/pull-down
and interrupts on input changes.
+config PINCTRL_STARFIVE_JHB100_PER2
+ tristate "StarFive JHB100 SoC Peripheral-2 pinctrl and GPIO driver"
+ depends on ARCH_STARFIVE || COMPILE_TEST
+ depends on OF
+ select PINCTRL_STARFIVE_JHB100
+ default ARCH_STARFIVE
+ help
+ Say yes here to support Peripheral-2 pin control on the StarFive JHB100 SoC.
+ This also provides an interface to the GPIO pins not used by other
+ peripherals supporting inputs, outputs, configuring pull-up/pull-down
+ and interrupts on input changes.
+
config PINCTRL_STARFIVE_JHB100_SYS0
tristate "StarFive JHB100 SoC System-0 pinctrl and GPIO driver"
depends on ARCH_STARFIVE || COMPILE_TEST
diff --git a/drivers/pinctrl/starfive/Makefile b/drivers/pinctrl/starfive/Makefile
index 6beef7e313ef..33213bd1919f 100644
--- a/drivers/pinctrl/starfive/Makefile
+++ b/drivers/pinctrl/starfive/Makefile
@@ -9,6 +9,7 @@ obj-$(CONFIG_PINCTRL_STARFIVE_JH7110_AON) += pinctrl-starfive-jh7110-aon.o
obj-$(CONFIG_PINCTRL_STARFIVE_JHB100) += pinctrl-starfive-jhb100.o
obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_PER0) += pinctrl-starfive-jhb100-per0.o
obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_PER1) += pinctrl-starfive-jhb100-per1.o
+obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_PER2) += pinctrl-starfive-jhb100-per2.o
obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_SYS0) += pinctrl-starfive-jhb100-sys0.o
obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_SYS0H) += pinctrl-starfive-jhb100-sys0h.o
obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_SYS1) += pinctrl-starfive-jhb100-sys1.o
diff --git a/drivers/pinctrl/starfive/pinctrl-starfive-jhb100-per2.c b/drivers/pinctrl/starfive/pinctrl-starfive-jhb100-per2.c
new file mode 100644
index 000000000000..b3af13abcffa
--- /dev/null
+++ b/drivers/pinctrl/starfive/pinctrl-starfive-jhb100-per2.c
@@ -0,0 +1,126 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Pinctrl / GPIO driver for StarFive JHB100 SoC Peripheral-2 domain
+ *
+ * Copyright (C) 2024 StarFive Technology Co., Ltd.
+ * Author: Alex Soo <yuklin.soo@starfivetech.com>
+ *
+ */
+
+#include <dt-bindings/pinctrl/starfive,jhb100-pinctrl.h>
+#include <linux/mod_devicetable.h>
+#include <linux/platform_device.h>
+
+#include "pinctrl-starfive-jhb100.h"
+
+static const struct jhb100_pin_layout_desc jhb100_per2_pl_desc[] = {
+ { .pin_start = 0, .pin_cnt = 15, .name = "gpio", .gpio_func_sel = 0 },
+ { .pin_start = 15, .pin_cnt = 1, .name = "gpio", .gpio_func_sel = -1 },
+ { .pin_start = 16, .pin_cnt = 15, .name = "gpio", .gpio_func_sel = 0 },
+ { 0xff },
+};
+
+static struct config_reg_layout_desc jhb100_per2_pinctrl_rl_desc[] = {
+ {
+ .pin_start = 0,
+ .pin_cnt = 19,
+ .drive_strength_2bit = { .shift = 0, .width = 2 },
+ .input_enable = { .shift = 2, .width = 1 },
+ .pull_down = { .shift = 3, .width = 1 },
+ .pull_up = { .shift = 4, .width = 1 },
+ .slew_rate = { .shift = 5, .width = 1 },
+ .schmitt_trigger_select = { .shift = 6, .width = 1 },
+ .reserved = { .shift = 7, .width = 8 },
+ .debounce_width = { .shift = 15, .width = 17 },
+ },
+ {
+ .pin_start = 19,
+ .pin_cnt = 12,
+ .input_enable = { .shift = 0, .width = 1 },
+ .slew_rate = { .shift = 1, .width = 1 },
+ .vsel = { .shift = 2, .width = 2 },
+ .reserved = { .shift = 4, .width = 11 },
+ .debounce_width = { .shift = 15, .width = 17 },
+ },
+ { 0xff },
+};
+
+static const struct pinvref_desc pinvref_desc_per2[] = {
+ {
+ .name = "gpionw",
+ .pin_grp = {
+ PADNUM_PER2_GPIO_D19,
+ PADNUM_PER2_GPIO_D20,
+ PADNUM_PER2_GPIO_D21,
+ PADNUM_PER2_GPIO_D22,
+ PADNUM_PER2_GPIO_D23,
+ PADNUM_PER2_GPIO_D24,
+ PADNUM_PER2_GPIO_D25,
+ PADNUM_PER2_GPIO_D26,
+ PADNUM_PER2_GPIO_D27,
+ PADNUM_PER2_GPIO_D28,
+ PADNUM_PER2_GPIO_D29,
+ PADNUM_PER2_GPIO_D30
+ },
+ .num_pins = 12,
+ .range = BIT(JHB100_PINVREF_1_8V) | BIT(JHB100_PINVREF_2_5V) |
+ BIT(JHB100_PINVREF_3_3V)
+ },
+ { NULL },
+};
+
+struct starfive_pinctrl_regs jhb100_per2_pinctrl_regs = {
+ .vref = { .reg = 0x00, .pv_desc = pinvref_desc_per2 },
+ .func_sel = { .reg = 0x8c, .width_per_pin = 2 },
+ .config = 0x04,
+ .output = 0x80,
+ .output_en = 0x84,
+ .gpio_status = 0x88,
+ .irq_en = 0x94,
+ .irq_status = 0x98,
+ .irq_clr = 0x9c,
+ .irq_trigger = 0xa0,
+ .irq_level = 0xa4,
+ .irq_both_edge = 0xa8,
+ .irq_edge = 0xac,
+};
+
+static const struct jhb100_pinctrl_func_maps jhb100_func_maps_per2[] = {
+ { .func = "fan_tach", .val = 1 },
+ { .func = "gmac_rgmii", .val = 1 },
+ { .func = "gmac_rmii", .val = 2 },
+ { .func = "gpio", .val = 0 },
+ { .func = "host0_port80", .val = 2 },
+ { .func = "host1_port80", .val = 3 },
+};
+
+static const struct jhb100_pinctrl_domain_info jhb100_per2_pinctrl_info = {
+ .name = "jhb100-per2",
+ .pl_desc = jhb100_per2_pl_desc,
+ .crl_desc = jhb100_per2_pinctrl_rl_desc,
+ .regs = &jhb100_per2_pinctrl_regs,
+ .fmaps = jhb100_func_maps_per2,
+ .num_maps = ARRAY_SIZE(jhb100_func_maps_per2),
+};
+
+static const struct of_device_id jhb100_per2_pinctrl_of_match[] = {
+ {
+ .compatible = "starfive,jhb100-per2-pinctrl",
+ .data = &jhb100_per2_pinctrl_info,
+ },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, jhb100_per2_pinctrl_of_match);
+
+static struct platform_driver jhb100_per2_pinctrl_driver = {
+ .probe = jhb100_pinctrl_probe,
+ .driver = {
+ .name = "starfive-jhb100-per2-pinctrl",
+ .of_match_table = jhb100_per2_pinctrl_of_match,
+ },
+};
+module_platform_driver(jhb100_per2_pinctrl_driver);
+
+MODULE_DESCRIPTION("Pinctrl driver for StarFive JHB100 SoC Peripheral-2 domain");
+MODULE_AUTHOR("Alex Soo <yuklin.soo@starfivetech.com>");
+MODULE_LICENSE("GPL");
--
2.25.1
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply related [flat|nested] 32+ messages in thread* [PATCH v2 18/22] dt-bindings: pinctrl: Add starfive,jhb100-per2pok-pinctrl
2026-05-14 11:11 [PATCH v2 00/22] Add basic pinctrl drivers for JHB100 SoC Changhuang Liang
` (16 preceding siblings ...)
2026-05-14 11:12 ` [PATCH v2 17/22] pinctrl: starfive: Add StarFive JHB100 per2 controller driver Changhuang Liang
@ 2026-05-14 11:12 ` Changhuang Liang
2026-05-14 13:17 ` Rob Herring (Arm)
2026-05-14 11:12 ` [PATCH v2 19/22] pinctrl: starfive: Add StarFive JHB100 per2pok controller driver Changhuang Liang
` (3 subsequent siblings)
21 siblings, 1 reply; 32+ messages in thread
From: Changhuang Liang @ 2026-05-14 11:12 UTC (permalink / raw)
To: Linus Walleij, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Emil Renner Berthing, Paul Walmsley, Albert Ou, Palmer Dabbelt,
Alexandre Ghiti, Philipp Zabel, Bartosz Golaszewski
Cc: linux-gpio, linux-kernel, devicetree, linux-riscv,
Lianfeng Ouyang, Changhuang Liang
Add pinctrl bindings for StarFive JHB100 SoC Peripheral-2 Power OK
(per2pok) pinctrl controller.
Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
---
.../starfive,jhb100-per2pok-pinctrl.yaml | 173 ++++++++++++++++++
.../pinctrl/starfive,jhb100-pinctrl.h | 20 ++
2 files changed, 193 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per2pok-pinctrl.yaml
diff --git a/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per2pok-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per2pok-pinctrl.yaml
new file mode 100644
index 000000000000..7ffebf6b1bcc
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per2pok-pinctrl.yaml
@@ -0,0 +1,173 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/starfive,jhb100-per2pok-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: StarFive JHB100 Peripheral-2 Power OK Pin Controller
+
+description: |
+ Pinctrl bindings for JHB100 RISC-V SoC from StarFive Technology Ltd.
+
+ The JHB100 SoC has 13 pinctrl domains - sys0, sys0h, sys1, sys2, per0, per1,
+ per2, per2pok, per3, adc0, adc1, emmc, and vga.
+ This document provides an overview of the "bper2pok" pinctrl domain.
+
+ The "per2pok" domain has a pin controller which provides
+ - function selection for GPIO pads.
+ - GPIO interrupt handling.
+
+ In the Peripheral-2 Power OK Pin Controller, there are 18 multi-function
+ GPIO_PADs. Each can be multiplexed to several peripherals through function
+ selection. Each iopad has a maximum of up to 4 functions - 0, 1, 2, and 3.
+ Function 0 is the default function or generally the GPIO function.
+ Function 1, 2, and 3 are alternate functions or peripheral signals that can
+ routed to an iopad. The function selection can be carried out by writing
+ the function number to the iopad function select register.
+
+ Each iopad is configurable with parameters such as input-enable, internal
+ pull-up/pull-down bias, drive strength, schmitt trigger, slew rate, input
+ debounce nanoseconds, power source and drive type (open-drain or push-pull).
+
+maintainers:
+ - Alex Soo <yuklin.soo@starfivetech.com>
+
+properties:
+ compatible:
+ items:
+ - const: starfive,jhb100-per2pok-pinctrl
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ resets:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ interrupt-controller: true
+
+ '#interrupt-cells':
+ const: 3
+
+ gpio-controller: true
+
+ '#gpio-cells':
+ const: 3
+
+ gpio-ranges: true
+
+ gpio-line-names: true
+
+patternProperties:
+ '-grp$':
+ type: object
+ additionalProperties: false
+ patternProperties:
+ '-pins$':
+ type: object
+ description: |
+ A pinctrl node should contain at least one subnode representing the
+ pinctrl groups available in the domain. Each subnode will list the
+ pins it needs, and how they should be configured, with regard to
+ function selection, bias, input enable/disable, input schmitt
+ trigger enable/disable, slew-rate, input debounce nanoseconds,
+ drive-open-drain, drive-push-pull, power-source and drive-strength.
+ allOf:
+ - $ref: /schemas/pinctrl/pincfg-node.yaml
+ - $ref: /schemas/pinctrl/pinmux-node.yaml
+ unevaluatedProperties: false
+
+ properties:
+ pins:
+ description:
+ The list of IOs that properties in the pincfg node apply to.
+
+ function:
+ description:
+ A string containing the name of the function to mux for these
+ pins.
+ enum: [ can, gpio, host0_port80, host1_port80, passthru, pwm ]
+
+ bias-disable: true
+
+ bias-pull-down:
+ type: boolean
+
+ bias-pull-up:
+ oneOf:
+ - type: boolean
+ - enum: [ 600, 900, 1200, 2000 ]
+ description: Pull up RSEL type resistance values (in ohms)
+ description:
+ For normal pull up type there is no need to specify a resistance
+ value, hence this can be specified as a boolean property.
+ For RSEL pull up type a resistance value (in ohms) can be added.
+
+ drive-open-drain: true
+
+ drive-push-pull: true
+
+ drive-strength:
+ enum: [ 2, 4, 8, 12 ]
+
+ drive-strength-microamp:
+ enum: [ 2000, 4000, 8000, 12000 ]
+
+ input-debounce-nanoseconds:
+ minimum: 0
+ maximum: 4294967295
+
+ input-disable: true
+
+ input-enable: true
+
+ input-schmitt-enable: true
+
+ input-schmitt-disable: true
+
+ power-source:
+ enum: [ 0, 1, 2 ]
+
+ slew-rate:
+ enum: [ 0, 1 ]
+ default: 0
+ description: |
+ 0: slow (half frequency)
+ 1: fast
+
+required:
+ - compatible
+ - reg
+ - resets
+ - interrupts
+ - interrupt-controller
+ - '#interrupt-cells'
+ - gpio-controller
+ - '#gpio-cells'
+ - gpio-ranges
+
+additionalProperties: false
+
+examples:
+ - |
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ pinctrl_per2pok: pinctrl@11bc2400 {
+ compatible = "starfive,jhb100-per2pok-pinctrl";
+ reg = <0x0 0x11bc2400 0x0 0x400>;
+ resets = <&per2crg 1>;
+ interrupts = <63>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ gpio-ranges = <&pinctrl_per2pok 0 0 0 18>;
+ };
+ };
diff --git a/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h b/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h
index 6a80c56304e8..5573b5b0420b 100644
--- a/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h
+++ b/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h
@@ -210,6 +210,26 @@
#define PADNUM_PER2_GPIO_D29 29
#define PADNUM_PER2_GPIO_D30 30
+/* per2pok pad numbers */
+#define PADNUM_PER2POK_GPIO_D31 0
+#define PADNUM_PER2POK_GPIO_D32 1
+#define PADNUM_PER2POK_GPIO_D33 2
+#define PADNUM_PER2POK_GPIO_D34 3
+#define PADNUM_PER2POK_GPIO_D35 4
+#define PADNUM_PER2POK_GPIO_D36 5
+#define PADNUM_PER2POK_GPIO_D37 6
+#define PADNUM_PER2POK_GPIO_D38 7
+#define PADNUM_PER2POK_GPIO_D39 8
+#define PADNUM_PER2POK_GPIO_D40 9
+#define PADNUM_PER2POK_GPIO_D41 10
+#define PADNUM_PER2POK_GPIO_D42 11
+#define PADNUM_PER2POK_GPIO_D43 12
+#define PADNUM_PER2POK_GPIO_D44 13
+#define PADNUM_PER2POK_GPIO_D45 14
+#define PADNUM_PER2POK_GPIO_D46 15
+#define PADNUM_PER2POK_GPIO_D47 16
+#define PADNUM_PER2POK_GPIO_D48 17
+
/* pinctrl hog power-source value */
#define JHB100_PINVREF_3_3V 0
#define JHB100_PINVREF_2_5V 1
--
2.25.1
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply related [flat|nested] 32+ messages in thread* Re: [PATCH v2 18/22] dt-bindings: pinctrl: Add starfive,jhb100-per2pok-pinctrl
2026-05-14 11:12 ` [PATCH v2 18/22] dt-bindings: pinctrl: Add starfive,jhb100-per2pok-pinctrl Changhuang Liang
@ 2026-05-14 13:17 ` Rob Herring (Arm)
0 siblings, 0 replies; 32+ messages in thread
From: Rob Herring (Arm) @ 2026-05-14 13:17 UTC (permalink / raw)
To: Changhuang Liang
Cc: Albert Ou, Alexandre Ghiti, Emil Renner Berthing, linux-kernel,
Conor Dooley, devicetree, Bartosz Golaszewski, linux-riscv,
linux-gpio, Krzysztof Kozlowski, Linus Walleij, Philipp Zabel,
Palmer Dabbelt, Paul Walmsley, Lianfeng Ouyang
On Thu, 14 May 2026 04:12:14 -0700, Changhuang Liang wrote:
> Add pinctrl bindings for StarFive JHB100 SoC Peripheral-2 Power OK
> (per2pok) pinctrl controller.
>
> Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
> ---
> .../starfive,jhb100-per2pok-pinctrl.yaml | 173 ++++++++++++++++++
> .../pinctrl/starfive,jhb100-pinctrl.h | 20 ++
> 2 files changed, 193 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per2pok-pinctrl.yaml
>
My bot found errors running 'make dt_binding_check' on your patch:
yamllint warnings/errors:
./Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per2pok-pinctrl.yaml:134:14: [warning] wrong indentation: expected 12 but found 13 (indentation)
./Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per2-pinctrl.yaml:136:14: [warning] wrong indentation: expected 12 but found 13 (indentation)
dtschema/dtc warnings/errors:
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per2-pinctrl.example.dtb: pinctrl@11bc2000 (starfive,jhb100-per2-pinctrl): gpio-ranges:1: [31] is too short
from schema $id: http://devicetree.org/schemas/gpio/gpio.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per2pok-pinctrl.example.dtb: pinctrl@11bc2400 (starfive,jhb100-per2pok-pinctrl): gpio-ranges:1: [18] is too short
from schema $id: http://devicetree.org/schemas/gpio/gpio.yaml
doc reference errors (make refcheckdocs):
See https://patchwork.kernel.org/project/devicetree/patch/20260514111218.94519-19-changhuang.liang@starfivetech.com
The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.
If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:
pip3 install dtschema --upgrade
Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply [flat|nested] 32+ messages in thread
* [PATCH v2 19/22] pinctrl: starfive: Add StarFive JHB100 per2pok controller driver
2026-05-14 11:11 [PATCH v2 00/22] Add basic pinctrl drivers for JHB100 SoC Changhuang Liang
` (17 preceding siblings ...)
2026-05-14 11:12 ` [PATCH v2 18/22] dt-bindings: pinctrl: Add starfive,jhb100-per2pok-pinctrl Changhuang Liang
@ 2026-05-14 11:12 ` Changhuang Liang
2026-05-14 11:12 ` [PATCH v2 20/22] dt-bindings: pinctrl: Add starfive,jhb100-per3-pinctrl Changhuang Liang
` (2 subsequent siblings)
21 siblings, 0 replies; 32+ messages in thread
From: Changhuang Liang @ 2026-05-14 11:12 UTC (permalink / raw)
To: Linus Walleij, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Emil Renner Berthing, Paul Walmsley, Albert Ou, Palmer Dabbelt,
Alexandre Ghiti, Philipp Zabel, Bartosz Golaszewski
Cc: linux-gpio, linux-kernel, devicetree, linux-riscv,
Lianfeng Ouyang, Changhuang Liang
Add pinctrl driver for StarFive JHB100 SoC Peripheral-2 Power OK
(per2pok) pinctrl controller.
Co-developed-by: Lianfeng Ouyang <lianfeng.ouyang@starfivetech.com>
Signed-off-by: Lianfeng Ouyang <lianfeng.ouyang@starfivetech.com>
Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
---
drivers/pinctrl/starfive/Kconfig | 12 +++
drivers/pinctrl/starfive/Makefile | 1 +
.../pinctrl-starfive-jhb100-per2pok.c | 97 +++++++++++++++++++
3 files changed, 110 insertions(+)
create mode 100644 drivers/pinctrl/starfive/pinctrl-starfive-jhb100-per2pok.c
diff --git a/drivers/pinctrl/starfive/Kconfig b/drivers/pinctrl/starfive/Kconfig
index edc3b6d9c8d7..bf5915e0a5f2 100644
--- a/drivers/pinctrl/starfive/Kconfig
+++ b/drivers/pinctrl/starfive/Kconfig
@@ -91,6 +91,18 @@ config PINCTRL_STARFIVE_JHB100_PER2
peripherals supporting inputs, outputs, configuring pull-up/pull-down
and interrupts on input changes.
+config PINCTRL_STARFIVE_JHB100_PER2POK
+ tristate "StarFive JHB100 SoC Peripheral-2 Power OK pinctrl and GPIO driver"
+ depends on ARCH_STARFIVE || COMPILE_TEST
+ depends on OF
+ select PINCTRL_STARFIVE_JHB100
+ default ARCH_STARFIVE
+ help
+ Say yes here to support Peripheral-2 Power OK pin control on the StarFive JHB100 SoC.
+ This also provides an interface to the GPIO pins not used by other
+ peripherals supporting inputs, outputs, configuring pull-up/pull-down
+ and interrupts on input changes.
+
config PINCTRL_STARFIVE_JHB100_SYS0
tristate "StarFive JHB100 SoC System-0 pinctrl and GPIO driver"
depends on ARCH_STARFIVE || COMPILE_TEST
diff --git a/drivers/pinctrl/starfive/Makefile b/drivers/pinctrl/starfive/Makefile
index 33213bd1919f..213002da9cdd 100644
--- a/drivers/pinctrl/starfive/Makefile
+++ b/drivers/pinctrl/starfive/Makefile
@@ -10,6 +10,7 @@ obj-$(CONFIG_PINCTRL_STARFIVE_JHB100) += pinctrl-starfive-jhb100.o
obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_PER0) += pinctrl-starfive-jhb100-per0.o
obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_PER1) += pinctrl-starfive-jhb100-per1.o
obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_PER2) += pinctrl-starfive-jhb100-per2.o
+obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_PER2POK) += pinctrl-starfive-jhb100-per2pok.o
obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_SYS0) += pinctrl-starfive-jhb100-sys0.o
obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_SYS0H) += pinctrl-starfive-jhb100-sys0h.o
obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_SYS1) += pinctrl-starfive-jhb100-sys1.o
diff --git a/drivers/pinctrl/starfive/pinctrl-starfive-jhb100-per2pok.c b/drivers/pinctrl/starfive/pinctrl-starfive-jhb100-per2pok.c
new file mode 100644
index 000000000000..abeeee2e7a00
--- /dev/null
+++ b/drivers/pinctrl/starfive/pinctrl-starfive-jhb100-per2pok.c
@@ -0,0 +1,97 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Pinctrl / GPIO driver for StarFive JHB100 SoC Peripheral-2 Power OK domain
+ *
+ * Copyright (C) 2024 StarFive Technology Co., Ltd.
+ * Author: Alex Soo <yuklin.soo@starfivetech.com>
+ *
+ */
+
+#include <dt-bindings/pinctrl/starfive,jhb100-pinctrl.h>
+#include <linux/mod_devicetable.h>
+#include <linux/platform_device.h>
+
+#include "pinctrl-starfive-jhb100.h"
+
+static const struct jhb100_pin_layout_desc jhb100_per2pok_pl_desc[] = {
+ { .pin_start = 0, .pin_cnt = 10, .name = "gpio", .gpio_func_sel = 0 },
+ { .pin_start = 10, .pin_cnt = 8, .name = "pwm_channel", .gpio_func_sel = 1 },
+ { 0xff },
+};
+
+static struct config_reg_layout_desc jhb100_per2pok_pinctrl_rl_desc[] = {
+ {
+ .pin_start = 0,
+ .pin_cnt = 18,
+ .drive_strength_2bit = { .shift = 0, .width = 2 },
+ .input_enable = { .shift = 2, .width = 1 },
+ .pull_down = { .shift = 3, .width = 1 },
+ .pull_up = { .shift = 4, .width = 1 },
+ .slew_rate = { .shift = 5, .width = 1 },
+ .schmitt_trigger_select = { .shift = 6, .width = 1 },
+ .reserved = { .shift = 7, .width = 8 },
+ .debounce_width = { .shift = 15, .width = 17 },
+ },
+ { 0xff },
+};
+
+struct starfive_pinctrl_regs jhb100_per2pok_pinctrl_regs = {
+ .func_sel = { .reg = 0x58, .width_per_pin = 2 },
+ .config = 0x04,
+ .output = 0x4c,
+ .output_en = 0x50,
+ .gpio_status = 0x54,
+ .irq_en = 0x60,
+ .irq_status = 0x64,
+ .irq_clr = 0x68,
+ .irq_trigger = 0x6c,
+ .irq_level = 0x70,
+ .irq_both_edge = 0x74,
+ .irq_edge = 0x78,
+};
+
+static const struct jhb100_pinctrl_func_maps jhb100_func_maps_per2pok[] = {
+ { .func = "can", .val = 1 },
+ { .func = "gpio", .val = 0,
+ .max_pin = JHB100_FUNC_MAPS_MAX_PIN(PADNUM_PER2POK_GPIO_D40) },
+ { .func = "gpio", .val = 1,
+ .max_pin = JHB100_FUNC_MAPS_MAX_PIN(PADNUM_PER2POK_GPIO_D48) },
+ { .func = "host0_port80", .val = 2 },
+ { .func = "host1_port80", .val = 3 },
+ { .func = "passthru", .val = 2,
+ .max_pin = JHB100_FUNC_MAPS_MAX_PIN(PADNUM_PER2POK_GPIO_D36) },
+ { .func = "passthru", .val = 1,
+ .max_pin = JHB100_FUNC_MAPS_MAX_PIN(PADNUM_PER2POK_GPIO_D40) },
+ { .func = "pwm", .val = 0 },
+};
+
+static const struct jhb100_pinctrl_domain_info jhb100_per2pok_pinctrl_info = {
+ .name = "jhb100-per2pok",
+ .pl_desc = jhb100_per2pok_pl_desc,
+ .crl_desc = jhb100_per2pok_pinctrl_rl_desc,
+ .regs = &jhb100_per2pok_pinctrl_regs,
+ .fmaps = jhb100_func_maps_per2pok,
+ .num_maps = ARRAY_SIZE(jhb100_func_maps_per2pok),
+};
+
+static const struct of_device_id jhb100_per2pok_pinctrl_of_match[] = {
+ {
+ .compatible = "starfive,jhb100-per2pok-pinctrl",
+ .data = &jhb100_per2pok_pinctrl_info,
+ },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, jhb100_per2pok_pinctrl_of_match);
+
+static struct platform_driver jhb100_per2pok_pinctrl_driver = {
+ .probe = jhb100_pinctrl_probe,
+ .driver = {
+ .name = "starfive-jhb100-per2pok-pinctrl",
+ .of_match_table = jhb100_per2pok_pinctrl_of_match,
+ },
+};
+module_platform_driver(jhb100_per2pok_pinctrl_driver);
+
+MODULE_DESCRIPTION("Pinctrl driver for StarFive JHB100 SoC Peripheral-2 Power OK domain");
+MODULE_AUTHOR("Alex Soo <yuklin.soo@starfivetech.com>");
+MODULE_LICENSE("GPL");
--
2.25.1
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply related [flat|nested] 32+ messages in thread* [PATCH v2 20/22] dt-bindings: pinctrl: Add starfive,jhb100-per3-pinctrl
2026-05-14 11:11 [PATCH v2 00/22] Add basic pinctrl drivers for JHB100 SoC Changhuang Liang
` (18 preceding siblings ...)
2026-05-14 11:12 ` [PATCH v2 19/22] pinctrl: starfive: Add StarFive JHB100 per2pok controller driver Changhuang Liang
@ 2026-05-14 11:12 ` Changhuang Liang
2026-05-14 13:17 ` Rob Herring (Arm)
2026-05-14 11:12 ` [PATCH v2 21/22] pinctrl: starfive: Add StarFive JHB100 per3 controller driver Changhuang Liang
2026-05-14 11:12 ` [PATCH v2 22/22] riscv: dts: starfive: jhb100: Add pinctrl nodes Changhuang Liang
21 siblings, 1 reply; 32+ messages in thread
From: Changhuang Liang @ 2026-05-14 11:12 UTC (permalink / raw)
To: Linus Walleij, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Emil Renner Berthing, Paul Walmsley, Albert Ou, Palmer Dabbelt,
Alexandre Ghiti, Philipp Zabel, Bartosz Golaszewski
Cc: linux-gpio, linux-kernel, devicetree, linux-riscv,
Lianfeng Ouyang, Changhuang Liang
Add pinctrl bindings for StarFive JHB100 SoC Peripheral-3(per3) pinctrl
controller.
Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
---
.../pinctrl/starfive,jhb100-per3-pinctrl.yaml | 173 ++++++++++++++++++
.../pinctrl/starfive,jhb100-pinctrl.h | 14 ++
2 files changed, 187 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per3-pinctrl.yaml
diff --git a/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per3-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per3-pinctrl.yaml
new file mode 100644
index 000000000000..a1e5e09c06b2
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per3-pinctrl.yaml
@@ -0,0 +1,173 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/starfive,jhb100-per3-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: StarFive JHB100 Peripheral-3 Pin Controller
+
+description: |
+ Pinctrl bindings for JHB100 RISC-V SoC from StarFive Technology Ltd.
+
+ The JHB100 SoC has 13 pinctrl domains - sys0, sys0h, sys1, sys2, per0, per1,
+ per2, per2pok, per3, adc0, adc1, emmc, and vga.
+ This document provides an overview of the "per3" pinctrl domain.
+
+ The "per3" domain has a pin controller which provides
+ - function selection for GPIO pads.
+ - GPIO interrupt handling.
+
+ In the Peripheral-3 Pin Controller, there are 11 multi-function GPIO_PADs.
+ Each of them can be multiplexed to several peripherals through function
+ selection. Each iopad has a maximum of up to 2 functions - 0 and 1.
+ Function 0 is the default function which is generally the GPIO function.
+ Function 1 is the alternate function or peripheral signal that can be
+ routed to an iopad. The function selection can be carried out by writing
+ the function number to the iopad function select register.
+
+ Each iopad is configurable with parameters such as input-enable, internal
+ pull-up/pull-down bias, drive strength, schmitt trigger, slew rate, input
+ debounce nanoseconds, power source and drive type (open-drain or push-pull).
+
+maintainers:
+ - Alex Soo <yuklin.soo@starfivetech.com>
+
+properties:
+ compatible:
+ items:
+ - const: starfive,jhb100-per3-pinctrl
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ resets:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ interrupt-controller: true
+
+ '#interrupt-cells':
+ const: 3
+
+ gpio-controller: true
+
+ '#gpio-cells':
+ const: 3
+
+ gpio-ranges: true
+
+ gpio-line-names: true
+
+patternProperties:
+ '-grp$':
+ type: object
+ additionalProperties: false
+ patternProperties:
+ '-pins$':
+ type: object
+ description: |
+ A pinctrl node should contain at least one subnode representing the
+ pinctrl groups available in the domain. Each subnode will list the
+ pins it needs, and how they should be configured, with regard to
+ function selection, bias, input enable/disable, input schmitt
+ trigger enable/disable, slew-rate, input debounce nanoseconds,
+ drive-open-drain, drive-push-pull, power-source and drive-strength.
+ allOf:
+ - $ref: /schemas/pinctrl/pincfg-node.yaml
+ - $ref: /schemas/pinctrl/pinmux-node.yaml
+ unevaluatedProperties: false
+
+ properties:
+ pins:
+ description:
+ The list of IOs that properties in the pincfg node apply to.
+
+ function:
+ description:
+ A string containing the name of the function to mux for these
+ pins.
+ enum: [ gmac_mdio, gmac_rmii, gpio ]
+
+ bias-disable: true
+
+ bias-pull-down:
+ type: boolean
+
+ bias-pull-up:
+ oneOf:
+ - type: boolean
+ - enum: [ 600, 900, 1200, 2000 ]
+ description: Pull up RSEL type resistance values (in ohms)
+ description:
+ For normal pull up type there is no need to specify a resistance
+ value, hence this can be specified as a boolean property.
+ For RSEL pull up type a resistance value (in ohms) can be added.
+
+ drive-open-drain: true
+
+ drive-push-pull: true
+
+ drive-strength:
+ enum: [ 2, 4, 8, 12 ]
+
+ drive-strength-microamp:
+ enum: [ 2000, 4000, 8000, 12000 ]
+
+ input-debounce-nanoseconds:
+ minimum: 0
+ maximum: 4294967295
+
+ input-disable: true
+
+ input-enable: true
+
+ input-schmitt-enable: true
+
+ input-schmitt-disable: true
+
+ power-source:
+ enum: [ 0, 1, 2 ]
+
+ slew-rate:
+ enum: [ 0, 1 ]
+ default: 0
+ description: |
+ 0: slow (half frequency)
+ 1: fast
+
+required:
+ - compatible
+ - reg
+ - resets
+ - interrupts
+ - interrupt-controller
+ - '#interrupt-cells'
+ - gpio-controller
+ - '#gpio-cells'
+ - gpio-ranges
+
+additionalProperties: false
+
+examples:
+ - |
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ pinctrl_per3: pinctrl@11c42000 {
+ compatible = "starfive,jhb100-per3-pinctrl";
+ reg = <0x0 0x11c42000 0x0 0x1000>;
+ resets = <&per3crg 6>;
+ interrupts = <64>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ gpio-ranges = <&pinctrl_per3 0 0 0 11>;
+ };
+ };
diff --git a/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h b/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h
index 5573b5b0420b..05fbb8e0343c 100644
--- a/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h
+++ b/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h
@@ -230,6 +230,20 @@
#define PADNUM_PER2POK_GPIO_D47 16
#define PADNUM_PER2POK_GPIO_D48 17
+/* per3 pad numbers */
+#define PADNUM_PER3_GPIO_E0 0
+#define PADNUM_PER3_GPIO_E1 1
+#define PADNUM_PER3_GPIO_E2 2
+#define PADNUM_PER3_GPIO_E3 3
+#define PADNUM_PER3_GPIO_E4 4
+#define PADNUM_PER3_GPIO_E5 5
+#define PADNUM_PER3_GPIO_E6 6
+#define PADNUM_PER3_GPIO_E7 7
+#define PADNUM_PER3_GPIO_E8 8
+#define PADNUM_PER3_GPIO_E9 9
+#define PADNUM_PER3_GPIO_E10 10
+#define PADNUM_PER3_GPIO_E11 11
+
/* pinctrl hog power-source value */
#define JHB100_PINVREF_3_3V 0
#define JHB100_PINVREF_2_5V 1
--
2.25.1
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply related [flat|nested] 32+ messages in thread* Re: [PATCH v2 20/22] dt-bindings: pinctrl: Add starfive,jhb100-per3-pinctrl
2026-05-14 11:12 ` [PATCH v2 20/22] dt-bindings: pinctrl: Add starfive,jhb100-per3-pinctrl Changhuang Liang
@ 2026-05-14 13:17 ` Rob Herring (Arm)
0 siblings, 0 replies; 32+ messages in thread
From: Rob Herring (Arm) @ 2026-05-14 13:17 UTC (permalink / raw)
To: Changhuang Liang
Cc: Philipp Zabel, Paul Walmsley, Alexandre Ghiti, linux-gpio,
Albert Ou, linux-riscv, Emil Renner Berthing, Krzysztof Kozlowski,
devicetree, Lianfeng Ouyang, linux-kernel, Bartosz Golaszewski,
Conor Dooley, Linus Walleij, Palmer Dabbelt
On Thu, 14 May 2026 04:12:16 -0700, Changhuang Liang wrote:
> Add pinctrl bindings for StarFive JHB100 SoC Peripheral-3(per3) pinctrl
> controller.
>
> Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
> ---
> .../pinctrl/starfive,jhb100-per3-pinctrl.yaml | 173 ++++++++++++++++++
> .../pinctrl/starfive,jhb100-pinctrl.h | 14 ++
> 2 files changed, 187 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per3-pinctrl.yaml
>
My bot found errors running 'make dt_binding_check' on your patch:
yamllint warnings/errors:
./Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys2-pinctrl.yaml:135:14: [warning] wrong indentation: expected 12 but found 13 (indentation)
./Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys1-pinctrl.yaml:136:14: [warning] wrong indentation: expected 12 but found 13 (indentation)
./Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per2pok-pinctrl.yaml:134:14: [warning] wrong indentation: expected 12 but found 13 (indentation)
./Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys0h-pinctrl.yaml:136:14: [warning] wrong indentation: expected 12 but found 13 (indentation)
./Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per2-pinctrl.yaml:136:14: [warning] wrong indentation: expected 12 but found 13 (indentation)
./Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per0-pinctrl.yaml:136:14: [warning] wrong indentation: expected 12 but found 13 (indentation)
./Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per3-pinctrl.yaml:134:14: [warning] wrong indentation: expected 12 but found 13 (indentation)
./Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per1-pinctrl.yaml:135:14: [warning] wrong indentation: expected 12 but found 13 (indentation)
./Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys0-pinctrl.yaml:136:14: [warning] wrong indentation: expected 12 but found 13 (indentation)
dtschema/dtc warnings/errors:
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/pci/toshiba,tc9563.example.dtb: pcie@0,0 (pci1179,0623): i2c-parent: [[4294967295, 119]] is too short
from schema $id: http://devicetree.org/schemas/pci/toshiba,tc9563.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/i2c/i2c-demux-pinctrl.example.dtb: i2c-mux3 (i2c-demux-pinctrl): i2c-parent:0: [2, 3, 4] is too long
from schema $id: http://devicetree.org/schemas/i2c/i2c-demux-pinctrl.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/net/renesas,ether.example.dtb: ethernet-phy@1 (ethernet-phy-id0022.1537): compatible: ['ethernet-phy-id0022.1537', 'ethernet-phy-ieee802.3-c22'] is too long
from schema $id: http://devicetree.org/schemas/net/micrel.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys0-pinctrl.example.dtb: pinctrl@13080000 (starfive,jhb100-sys0-pinctrl): gpio-ranges:1: [4] is too short
from schema $id: http://devicetree.org/schemas/gpio/gpio.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/usb/ti,keystone-dwc3.example.dtb: dwc3@2680000 (ti,keystone-dwc3): usb@2690000:usb-phy:0: [4294967295, 4294967295] is too long
from schema $id: http://devicetree.org/schemas/usb/ti,keystone-dwc3.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/usb/ti,keystone-dwc3.example.dtb: dwc3@2680000 (ti,keystone-dwc3): usb@2690000: Unevaluated properties are not allowed ('usb-phy' was unexpected)
from schema $id: http://devicetree.org/schemas/usb/ti,keystone-dwc3.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/usb/ti,keystone-dwc3.example.dtb: usb@2690000 (snps,dwc3): usb-phy:0: [4294967295, 4294967295] is too long
from schema $id: http://devicetree.org/schemas/usb/snps,dwc3.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/usb/ti,keystone-dwc3.example.dtb: usb@2690000 (snps,dwc3): Unevaluated properties are not allowed ('usb-phy' was unexpected)
from schema $id: http://devicetree.org/schemas/usb/snps,dwc3.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/usb/snps,dwc3.example.dtb: usb@4a030000 (snps,dwc3): usb-phy:0: [4294967295, 4294967295] is too long
from schema $id: http://devicetree.org/schemas/usb/snps,dwc3.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/usb/snps,dwc3.example.dtb: usb@4a030000 (snps,dwc3): Unevaluated properties are not allowed ('snps,incr-burst-type-adjustment', 'usb-phy' were unexpected)
from schema $id: http://devicetree.org/schemas/usb/snps,dwc3.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/usb/usb-drd.example.dtb: usb@4a030000 (snps,dwc3): usb-phy:0: [4294967295, 4294967295] is too long
from schema $id: http://devicetree.org/schemas/usb/snps,dwc3.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/usb/usb-drd.example.dtb: usb@4a030000 (snps,dwc3): Unevaluated properties are not allowed ('adp-disable', 'dr_mode', 'maximum-speed', 'otg-rev', 'phy_type', 'usb-phy' were unexpected)
from schema $id: http://devicetree.org/schemas/usb/snps,dwc3.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys2-pinctrl.example.dtb: pinctrl@13082000 (starfive,jhb100-sys2-pinctrl): gpio-ranges:2: [32, 5] is too short
from schema $id: http://devicetree.org/schemas/gpio/gpio.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys1-pinctrl.example.dtb: pinctrl@13081000 (starfive,jhb100-sys1-pinctrl): gpio-ranges:1: [8] is too short
from schema $id: http://devicetree.org/schemas/gpio/gpio.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per2pok-pinctrl.example.dtb: pinctrl@11bc2400 (starfive,jhb100-per2pok-pinctrl): gpio-ranges:1: [18] is too short
from schema $id: http://devicetree.org/schemas/gpio/gpio.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys0h-pinctrl.example.dtb: pinctrl@13080800 (starfive,jhb100-sys0h-pinctrl): gpio-ranges:1: [12] is too short
from schema $id: http://devicetree.org/schemas/gpio/gpio.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per2-pinctrl.example.dtb: pinctrl@11bc2000 (starfive,jhb100-per2-pinctrl): gpio-ranges:1: [31] is too short
from schema $id: http://devicetree.org/schemas/gpio/gpio.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per3-pinctrl.example.dtb: pinctrl@11c42000 (starfive,jhb100-per3-pinctrl): gpio-ranges:1: [11] is too short
from schema $id: http://devicetree.org/schemas/gpio/gpio.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per0-pinctrl.example.dtb: pinctrl@11a0a000 (starfive,jhb100-per0-pinctrl): gpio-ranges:2: [32, 28] is too short
from schema $id: http://devicetree.org/schemas/gpio/gpio.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-per1-pinctrl.example.dtb: pinctrl@11b42000 (starfive,jhb100-per1-pinctrl): gpio-ranges:2: [32, 4] is too short
from schema $id: http://devicetree.org/schemas/gpio/gpio.yaml
doc reference errors (make refcheckdocs):
See https://patchwork.kernel.org/project/devicetree/patch/20260514111218.94519-21-changhuang.liang@starfivetech.com
The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.
If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:
pip3 install dtschema --upgrade
Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply [flat|nested] 32+ messages in thread
* [PATCH v2 21/22] pinctrl: starfive: Add StarFive JHB100 per3 controller driver
2026-05-14 11:11 [PATCH v2 00/22] Add basic pinctrl drivers for JHB100 SoC Changhuang Liang
` (19 preceding siblings ...)
2026-05-14 11:12 ` [PATCH v2 20/22] dt-bindings: pinctrl: Add starfive,jhb100-per3-pinctrl Changhuang Liang
@ 2026-05-14 11:12 ` Changhuang Liang
2026-05-14 11:12 ` [PATCH v2 22/22] riscv: dts: starfive: jhb100: Add pinctrl nodes Changhuang Liang
21 siblings, 0 replies; 32+ messages in thread
From: Changhuang Liang @ 2026-05-14 11:12 UTC (permalink / raw)
To: Linus Walleij, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Emil Renner Berthing, Paul Walmsley, Albert Ou, Palmer Dabbelt,
Alexandre Ghiti, Philipp Zabel, Bartosz Golaszewski
Cc: linux-gpio, linux-kernel, devicetree, linux-riscv,
Lianfeng Ouyang, Changhuang Liang
Add pinctrl driver for StarFive JHB100 SoC Peripheral-3(per3) pinctrl
controller.
Co-developed-by: Lianfeng Ouyang <lianfeng.ouyang@starfivetech.com>
Signed-off-by: Lianfeng Ouyang <lianfeng.ouyang@starfivetech.com>
Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
---
drivers/pinctrl/starfive/Kconfig | 12 ++
drivers/pinctrl/starfive/Makefile | 1 +
.../starfive/pinctrl-starfive-jhb100-per3.c | 121 ++++++++++++++++++
3 files changed, 134 insertions(+)
create mode 100644 drivers/pinctrl/starfive/pinctrl-starfive-jhb100-per3.c
diff --git a/drivers/pinctrl/starfive/Kconfig b/drivers/pinctrl/starfive/Kconfig
index bf5915e0a5f2..da1dcdcc4140 100644
--- a/drivers/pinctrl/starfive/Kconfig
+++ b/drivers/pinctrl/starfive/Kconfig
@@ -103,6 +103,18 @@ config PINCTRL_STARFIVE_JHB100_PER2POK
peripherals supporting inputs, outputs, configuring pull-up/pull-down
and interrupts on input changes.
+config PINCTRL_STARFIVE_JHB100_PER3
+ tristate "StarFive JHB100 SoC Peripheral-3 pinctrl and GPIO driver"
+ depends on ARCH_STARFIVE || COMPILE_TEST
+ depends on OF
+ select PINCTRL_STARFIVE_JHB100
+ default ARCH_STARFIVE
+ help
+ Say yes here to support Peripheral-3 pin control on the StarFive JHB100 SoC.
+ This also provides an interface to the GPIO pins not used by other
+ peripherals supporting inputs, outputs, configuring pull-up/pull-down
+ and interrupts on input changes.
+
config PINCTRL_STARFIVE_JHB100_SYS0
tristate "StarFive JHB100 SoC System-0 pinctrl and GPIO driver"
depends on ARCH_STARFIVE || COMPILE_TEST
diff --git a/drivers/pinctrl/starfive/Makefile b/drivers/pinctrl/starfive/Makefile
index 213002da9cdd..351fce524fec 100644
--- a/drivers/pinctrl/starfive/Makefile
+++ b/drivers/pinctrl/starfive/Makefile
@@ -11,6 +11,7 @@ obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_PER0) += pinctrl-starfive-jhb100-per0.o
obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_PER1) += pinctrl-starfive-jhb100-per1.o
obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_PER2) += pinctrl-starfive-jhb100-per2.o
obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_PER2POK) += pinctrl-starfive-jhb100-per2pok.o
+obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_PER3) += pinctrl-starfive-jhb100-per3.o
obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_SYS0) += pinctrl-starfive-jhb100-sys0.o
obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_SYS0H) += pinctrl-starfive-jhb100-sys0h.o
obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_SYS1) += pinctrl-starfive-jhb100-sys1.o
diff --git a/drivers/pinctrl/starfive/pinctrl-starfive-jhb100-per3.c b/drivers/pinctrl/starfive/pinctrl-starfive-jhb100-per3.c
new file mode 100644
index 000000000000..cacbed03a123
--- /dev/null
+++ b/drivers/pinctrl/starfive/pinctrl-starfive-jhb100-per3.c
@@ -0,0 +1,121 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Pinctrl / GPIO driver for StarFive JHB100 SoC Peripheral-3 domain
+ *
+ * Copyright (C) 2024 StarFive Technology Co., Ltd.
+ * Author: Alex Soo <yuklin.soo@starfivetech.com>
+ *
+ */
+
+#include <dt-bindings/pinctrl/starfive,jhb100-pinctrl.h>
+#include <linux/mod_devicetable.h>
+#include <linux/platform_device.h>
+
+#include "pinctrl-starfive-jhb100.h"
+
+static const struct jhb100_pin_layout_desc jhb100_per3_pl_desc[] = {
+ { .pin_start = 0, .pin_cnt = 11, .name = "gpio", .gpio_func_sel = 0 },
+ { .pin_start = 11, .pin_cnt = 1, .name = "peci1_out", .gpio_func_sel = -1 },
+ { .pin_start = 12, .pin_cnt = 1, .name = "peci2_out", .gpio_func_sel = -1 },
+ { 0xff },
+};
+
+static struct config_reg_layout_desc jhb100_per3_pinctrl_rl_desc[] = {
+ {
+ .pin_start = 0,
+ .pin_cnt = 2,
+ .drive_strength_2bit = { .shift = 0, .width = 2 },
+ .input_enable = { .shift = 2, .width = 1 },
+ .pull_down = { .shift = 3, .width = 1 },
+ .pull_up = { .shift = 4, .width = 1 },
+ .slew_rate = { .shift = 5, .width = 1 },
+ .schmitt_trigger_select = { .shift = 6, .width = 1 },
+ .reserved = { .shift = 7, .width = 8 },
+ .debounce_width = { .shift = 15, .width = 17 },
+ },
+ {
+ .pin_start = 2,
+ .pin_cnt = 9,
+ .input_enable = { .shift = 0, .width = 1 },
+ .slew_rate = { .shift = 1, .width = 1 },
+ .vsel = { .shift = 2, .width = 2 },
+ .reserved = { .shift = 4, .width = 11 },
+ .debounce_width = { .shift = 15, .width = 17 },
+ },
+ { 0xff },
+};
+
+static const struct pinvref_desc pinvref_desc_per3[] = {
+ {
+ .name = "gpios",
+ .pin_grp = {
+ PADNUM_PER3_GPIO_E0,
+ PADNUM_PER3_GPIO_E1,
+ PADNUM_PER3_GPIO_E2,
+ PADNUM_PER3_GPIO_E3,
+ PADNUM_PER3_GPIO_E4,
+ PADNUM_PER3_GPIO_E5,
+ PADNUM_PER3_GPIO_E6,
+ PADNUM_PER3_GPIO_E7,
+ PADNUM_PER3_GPIO_E8,
+ PADNUM_PER3_GPIO_E9,
+ PADNUM_PER3_GPIO_E10
+ },
+ .num_pins = 11,
+ .range = BIT(JHB100_PINVREF_1_8V) | BIT(JHB100_PINVREF_3_3V)
+ },
+ { NULL },
+};
+
+struct starfive_pinctrl_regs jhb100_per3_pinctrl_regs = {
+ .vref = { .reg = 0x00, .pv_desc = pinvref_desc_per3 },
+ .func_sel = { .reg = 0x3c, .width_per_pin = 2 },
+ .config = 0x04,
+ .output = 0x30,
+ .output_en = 0x34,
+ .gpio_status = 0x38,
+ .irq_en = 0x40,
+ .irq_status = 0x44,
+ .irq_clr = 0x48,
+ .irq_trigger = 0x4c,
+ .irq_level = 0x50,
+ .irq_both_edge = 0x54,
+ .irq_edge = 0x58,
+};
+
+static const struct jhb100_pinctrl_func_maps jhb100_func_maps_per3[] = {
+ { .func = "gmac_mdio", .val = 1 },
+ { .func = "gmac_rmii", .val = 1 },
+ { .func = "gpio", .val = 0 },
+};
+
+static const struct jhb100_pinctrl_domain_info jhb100_per3_pinctrl_info = {
+ .name = "jhb100-per3",
+ .pl_desc = jhb100_per3_pl_desc,
+ .crl_desc = jhb100_per3_pinctrl_rl_desc,
+ .regs = &jhb100_per3_pinctrl_regs,
+ .fmaps = jhb100_func_maps_per3,
+ .num_maps = ARRAY_SIZE(jhb100_func_maps_per3),
+};
+
+static const struct of_device_id jhb100_per3_pinctrl_of_match[] = {
+ {
+ .compatible = "starfive,jhb100-per3-pinctrl",
+ .data = &jhb100_per3_pinctrl_info,
+ },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, jhb100_per3_pinctrl_of_match);
+
+static struct platform_driver jhb100_per3_pinctrl_driver = {
+ .probe = jhb100_pinctrl_probe,
+ .driver = {
+ .name = "starfive-jhb100-per3-pinctrl",
+ .of_match_table = jhb100_per3_pinctrl_of_match,
+ },
+};
+module_platform_driver(jhb100_per3_pinctrl_driver);
+
+MODULE_DESCRIPTION("Pinctrl driver for StarFive JHB100 SoC Peripheral-3 domain");
+MODULE_AUTHOR("Alex Soo <yuklin.soo@starfivetech.com>");
+MODULE_LICENSE("GPL");
--
2.25.1
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply related [flat|nested] 32+ messages in thread* [PATCH v2 22/22] riscv: dts: starfive: jhb100: Add pinctrl nodes
2026-05-14 11:11 [PATCH v2 00/22] Add basic pinctrl drivers for JHB100 SoC Changhuang Liang
` (20 preceding siblings ...)
2026-05-14 11:12 ` [PATCH v2 21/22] pinctrl: starfive: Add StarFive JHB100 per3 controller driver Changhuang Liang
@ 2026-05-14 11:12 ` Changhuang Liang
21 siblings, 0 replies; 32+ messages in thread
From: Changhuang Liang @ 2026-05-14 11:12 UTC (permalink / raw)
To: Linus Walleij, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Emil Renner Berthing, Paul Walmsley, Albert Ou, Palmer Dabbelt,
Alexandre Ghiti, Philipp Zabel, Bartosz Golaszewski
Cc: linux-gpio, linux-kernel, devicetree, linux-riscv,
Lianfeng Ouyang, Changhuang Liang
Add pinctrl nodes for starfive JHB100 SoC. They contain
pinctrl_per0/pinctrl_per1/pinctrl_per2/pinctrl_per2pok/pinctrl_per3/
pinctrl_sys0/pinctrl_sys0h/pinctrl_sys1/pinctrl_sys2.
Simultaneously initialize the pinctrl hog configuration and add a
pinctrl reference for uart6.
Co-developed-by: Lianfeng Ouyang <lianfeng.ouyang@starfivetech.com>
Signed-off-by: Lianfeng Ouyang <lianfeng.ouyang@starfivetech.com>
Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
---
arch/riscv/boot/dts/starfive/jhb100-evb1.dts | 35 ++++
.../boot/dts/starfive/jhb100-pinctrl.dtsi | 188 ++++++++++++++++++
arch/riscv/boot/dts/starfive/jhb100.dtsi | 110 ++++++++++
3 files changed, 333 insertions(+)
create mode 100644 arch/riscv/boot/dts/starfive/jhb100-pinctrl.dtsi
diff --git a/arch/riscv/boot/dts/starfive/jhb100-evb1.dts b/arch/riscv/boot/dts/starfive/jhb100-evb1.dts
index 462b6fb7953b..bffecc986b30 100644
--- a/arch/riscv/boot/dts/starfive/jhb100-evb1.dts
+++ b/arch/riscv/boot/dts/starfive/jhb100-evb1.dts
@@ -4,6 +4,7 @@
*/
#include "jhb100.dtsi"
+#include "jhb100-pinctrl.dtsi"
/ {
model = "StarFive JHB100 EVB-1";
@@ -27,6 +28,40 @@ memory@40000000 {
};
};
+&pinctrl_per0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpioe_i3c0_configs
+ &gpioe_i3c1_configs
+ &gpioe_i3c2_configs
+ &gpioe_i3c4_configs>;
+};
+
+&pinctrl_per1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpioe_spi_configs
+ &gpioe_qspi0_configs
+ &gpioe_qspi1_configs
+ &gpioe_qspi2_configs>;
+};
+
+&pinctrl_per2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpionw_configs>;
+};
+
+&pinctrl_per3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpios_configs>;
+};
+
+&pinctrl_sys2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpiow0_configs
+ &gpiow_inner_configs>;
+};
+
&uart6 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart6_pins>;
};
diff --git a/arch/riscv/boot/dts/starfive/jhb100-pinctrl.dtsi b/arch/riscv/boot/dts/starfive/jhb100-pinctrl.dtsi
new file mode 100644
index 000000000000..926e018165fe
--- /dev/null
+++ b/arch/riscv/boot/dts/starfive/jhb100-pinctrl.dtsi
@@ -0,0 +1,188 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+/*
+ * Copyright (c) 2025-2026 StarFive Technology Co., Ltd.
+ */
+
+#include <dt-bindings/pinctrl/starfive,jhb100-pinctrl.h>
+
+&pinctrl_per0 {
+ gpioe_i3c0_configs: gpioe-i3c0-hog-grp {
+ gpioe-i3c0-hog-pins {
+ pins = <PADNUM_PER0_GPIO_B8
+ PADNUM_PER0_GPIO_B9
+ PADNUM_PER0_GPIO_B10
+ PADNUM_PER0_GPIO_B11
+ PADNUM_PER0_GPIO_B32
+ PADNUM_PER0_GPIO_B33>;
+ power-source = <JHB100_PINVREF_3_3V>;
+ };
+ };
+
+ gpioe_i3c1_configs: gpioe-i3c1-hog-grp {
+ gpioe-i3c1-hog-pins {
+ pins = <PADNUM_PER0_GPIO_B12
+ PADNUM_PER0_GPIO_B13
+ PADNUM_PER0_GPIO_B14
+ PADNUM_PER0_GPIO_B15
+ PADNUM_PER0_GPIO_B34
+ PADNUM_PER0_GPIO_B35>;
+ power-source = <JHB100_PINVREF_3_3V>;
+ };
+ };
+
+ gpioe_i3c2_configs: gpioe-i3c2-hog-grp {
+ gpioe-i3c2-hog-pins {
+ pins = <PADNUM_PER0_GPIO_B16
+ PADNUM_PER0_GPIO_B17
+ PADNUM_PER0_GPIO_B18
+ PADNUM_PER0_GPIO_B19
+ PADNUM_PER0_GPIO_B20
+ PADNUM_PER0_GPIO_B21
+ PADNUM_PER0_GPIO_B22
+ PADNUM_PER0_GPIO_B23>;
+ power-source = <JHB100_PINVREF_3_3V>;
+ };
+ };
+
+ gpioe_i3c4_configs: gpioe-i3c4-hog-grp {
+ gpioe-i3c4-hog-pins {
+ pins = <PADNUM_PER0_GPIO_B36
+ PADNUM_PER0_GPIO_B37
+ PADNUM_PER0_GPIO_B38
+ PADNUM_PER0_GPIO_B39
+ PADNUM_PER0_GPIO_B40
+ PADNUM_PER0_GPIO_B41
+ PADNUM_PER0_GPIO_B42
+ PADNUM_PER0_GPIO_B43>;
+ power-source = <JHB100_PINVREF_3_3V>;
+ };
+ };
+};
+
+&pinctrl_per1 {
+ gpioe_spi_configs: gpioe-spi-hog-grp {
+ gpioe-spi-hog-pins {
+ pins = <PADNUM_PER1_GPIO_C0
+ PADNUM_PER1_GPIO_C1
+ PADNUM_PER1_GPIO_C2
+ PADNUM_PER1_GPIO_C3
+ PADNUM_PER1_GPIO_C4>;
+ power-source = <JHB100_PINVREF_3_3V>;
+ };
+ };
+
+ gpioe_qspi0_configs: gpioe-qspi0-hog-grp {
+ gpioe-qspi0-hog-pins {
+ pins = <PADNUM_PER1_GPIO_C5
+ PADNUM_PER1_GPIO_C6
+ PADNUM_PER1_GPIO_C7
+ PADNUM_PER1_GPIO_C8
+ PADNUM_PER1_GPIO_C9
+ PADNUM_PER1_GPIO_C10
+ PADNUM_PER1_GPIO_C11>;
+ power-source = <JHB100_PINVREF_3_3V>;
+ };
+ };
+
+ gpioe_qspi1_configs: gpioe-qspi1-hog-grp {
+ gpioe-qspi1-hog-pins {
+ pins = <PADNUM_PER1_GPIO_C12
+ PADNUM_PER1_GPIO_C13
+ PADNUM_PER1_GPIO_C14
+ PADNUM_PER1_GPIO_C15
+ PADNUM_PER1_GPIO_C16
+ PADNUM_PER1_GPIO_C17
+ PADNUM_PER1_GPIO_C18
+ PADNUM_PER1_GPIO_C19>;
+ power-source = <JHB100_PINVREF_3_3V>;
+ };
+ };
+
+ gpioe_qspi2_configs: gpioe-qspi2-hog-grp {
+ gpioe-qspi2-hog-pins {
+ pins = <PADNUM_PER1_GPIO_C20
+ PADNUM_PER1_GPIO_C21
+ PADNUM_PER1_GPIO_C22
+ PADNUM_PER1_GPIO_C23
+ PADNUM_PER1_GPIO_C24
+ PADNUM_PER1_GPIO_C25
+ PADNUM_PER1_GPIO_C26
+ PADNUM_PER1_GPIO_C27>;
+ power-source = <JHB100_PINVREF_3_3V>;
+ };
+ };
+};
+
+&pinctrl_per2 {
+ gpionw_configs: gpionw-hog-grp {
+ gpionw-hog-pins {
+ pins = <PADNUM_PER2_GPIO_D19
+ PADNUM_PER2_GPIO_D20
+ PADNUM_PER2_GPIO_D21
+ PADNUM_PER2_GPIO_D22
+ PADNUM_PER2_GPIO_D23
+ PADNUM_PER2_GPIO_D24
+ PADNUM_PER2_GPIO_D25
+ PADNUM_PER2_GPIO_D26
+ PADNUM_PER2_GPIO_D27
+ PADNUM_PER2_GPIO_D28
+ PADNUM_PER2_GPIO_D29
+ PADNUM_PER2_GPIO_D30>;
+ power-source = <2>;
+ };
+ };
+};
+
+&pinctrl_per3 {
+ gpios_configs: gpios-hog-grp {
+ gpios-hog-pins {
+ pins = <PADNUM_PER3_GPIO_E0
+ PADNUM_PER3_GPIO_E1
+ PADNUM_PER3_GPIO_E2
+ PADNUM_PER3_GPIO_E3
+ PADNUM_PER3_GPIO_E4
+ PADNUM_PER3_GPIO_E5
+ PADNUM_PER3_GPIO_E6
+ PADNUM_PER3_GPIO_E7
+ PADNUM_PER3_GPIO_E8
+ PADNUM_PER3_GPIO_E9
+ PADNUM_PER3_GPIO_E10>;
+ power-source = <JHB100_PINVREF_1_8V>;
+ };
+ };
+};
+
+&pinctrl_sys2 {
+ gpiow0_configs: gpiow0-hog-grp {
+ gpiow0-hog-pins {
+ pins = <PADNUM_SYS2_GPIO_A36
+ PADNUM_SYS2_GPIO_A37
+ PADNUM_SYS2_GPIO_A38
+ PADNUM_SYS2_GPIO_A39>;
+ power-source = <JHB100_PINVREF_3_3V>;
+ };
+ };
+
+ gpiow_inner_configs: gpiow-inner-hog-grp {
+ gpiow-inner-hog-pins {
+ pins = <PADNUM_SYS2_GPIO_A40
+ PADNUM_SYS2_GPIO_A41
+ PADNUM_SYS2_GPIO_A42
+ PADNUM_SYS2_GPIO_A43>;
+ power-source = <JHB100_PINVREF_3_3V>;
+ };
+ };
+
+ uart6_pins: uart6-grp {
+ uart6-tx-pins {
+ pins = <PADNUM_SYS2_GPIO_A38>;
+ function = "uart";
+ };
+
+ uart6-rx-pins {
+ pins = <PADNUM_SYS2_GPIO_A39>;
+ function = "uart";
+ input-enable;
+ };
+ };
+};
diff --git a/arch/riscv/boot/dts/starfive/jhb100.dtsi b/arch/riscv/boot/dts/starfive/jhb100.dtsi
index 943324b3b2fd..f9a7fa9d37e3 100644
--- a/arch/riscv/boot/dts/starfive/jhb100.dtsi
+++ b/arch/riscv/boot/dts/starfive/jhb100.dtsi
@@ -428,6 +428,19 @@ per0crg: clock-controller@11a08000 {
#reset-cells = <1>;
};
+ pinctrl_per0: pinctrl@11a0a000 {
+ compatible = "starfive,jhb100-per0-pinctrl";
+ reg = <0x0 0x11a0a000 0x0 0x1000>;
+ resets = <&per0crg JHB100_PER0RST_GPIO_IOMUX_PRESETN>;
+ interrupts = <60>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ gpio-ranges = <&pinctrl_per0 0 0 0 32>,
+ <&pinctrl_per0 1 0 32 28>;
+ };
+
per1crg: clock-controller@11b40000 {
compatible = "starfive,jhb100-per1crg";
reg = <0x0 0x11b40000 0x0 0x1000>;
@@ -443,6 +456,19 @@ per1crg: clock-controller@11b40000 {
#reset-cells = <1>;
};
+ pinctrl_per1: pinctrl@11b42000 {
+ compatible = "starfive,jhb100-per1-pinctrl";
+ reg = <0x0 0x11b42000 0x0 0x800>;
+ resets = <&per1crg JHB100_PER1RST_IOMUX_PRESETN>;
+ interrupts = <61>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ gpio-ranges = <&pinctrl_per1 0 0 0 32>,
+ <&pinctrl_per1 1 0 32 4>;
+ };
+
per2crg: clock-controller@11bc0000 {
compatible = "starfive,jhb100-per2crg";
reg = <0x0 0x11bc0000 0x0 0x1000>;
@@ -464,6 +490,30 @@ per2crg: clock-controller@11bc0000 {
#reset-cells = <1>;
};
+ pinctrl_per2: pinctrl@11bc2000 {
+ compatible = "starfive,jhb100-per2-pinctrl";
+ reg = <0x0 0x11bc2000 0x0 0x400>;
+ resets = <&per2crg JHB100_PER2RST_IOMUX_PRESETN>;
+ interrupts = <62>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ gpio-ranges = <&pinctrl_per2 0 0 0 31>;
+ };
+
+ pinctrl_per2pok: pinctrl@11bc2400 {
+ compatible = "starfive,jhb100-per2pok-pinctrl";
+ reg = <0x0 0x11bc2400 0x0 0x400>;
+ resets = <&per2crg JHB100_PER2RST_POK_IOMUX_PRESETN>;
+ interrupts = <63>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ gpio-ranges = <&pinctrl_per2pok 0 0 0 18>;
+ };
+
per3crg: clock-controller@11c40000 {
compatible = "starfive,jhb100-per3crg";
reg = <0x0 0x11c40000 0x0 0x1000>;
@@ -483,6 +533,18 @@ per3crg: clock-controller@11c40000 {
#reset-cells = <1>;
};
+ pinctrl_per3: pinctrl@11c42000 {
+ compatible = "starfive,jhb100-per3-pinctrl";
+ reg = <0x0 0x11c42000 0x0 0x1000>;
+ resets = <&per3crg JHB100_PER3RST_IOMUX_PRESETN>;
+ interrupts = <64>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ gpio-ranges = <&pinctrl_per3 0 0 0 11>;
+ };
+
sys0crg: clock-controller@13000000 {
compatible = "starfive,jhb100-sys0crg";
reg = <0x0 0x13000000 0x0 0x4000>;
@@ -517,6 +579,54 @@ sys2crg: clock-controller@13008000 {
#reset-cells = <1>;
};
+ pinctrl_sys0: pinctrl@13080000 {
+ compatible = "starfive,jhb100-sys0-pinctrl";
+ reg = <0x0 0x13080000 0x0 0x800>;
+ resets = <&sys0crg JHB100_SYS0RST_SYS0_IOMUX_PRESETN>;
+ interrupts = <56>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ gpio-ranges = <&pinctrl_sys0 0 0 0 4>;
+ };
+
+ pinctrl_sys0h: pinctrl@13080800 {
+ compatible = "starfive,jhb100-sys0h-pinctrl";
+ reg = <0x0 0x13080800 0x0 0x800>;
+ resets = <&sys0crg JHB100_SYS0RST_SYS0H_IOMUX_PRESETN>;
+ interrupts = <57>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ gpio-ranges = <&pinctrl_sys0h 0 0 0 12>;
+ };
+
+ pinctrl_sys1: pinctrl@13081000 {
+ compatible = "starfive,jhb100-sys1-pinctrl";
+ reg = <0x0 0x13081000 0x0 0x1000>;
+ resets = <&sys1crg JHB100_SYS1RST_SYS1_IOMUX_PRESETN>;
+ interrupts = <58>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ gpio-ranges = <&pinctrl_sys1 0 0 0 8>;
+ };
+
+ pinctrl_sys2: pinctrl@13082000 {
+ compatible = "starfive,jhb100-sys2-pinctrl";
+ reg = <0x0 0x13082000 0x0 0x1000>;
+ interrupts = <59>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ gpio-ranges = <&pinctrl_sys2 0 0 0 32>,
+ <&pinctrl_sys2 1 0 32 5>;
+ };
+
intc: interrupt-controller@13220000 {
compatible = "starfive,jhb100-intc";
reg = <0x0 0x13220000 0x0 0x80>;
--
2.25.1
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply related [flat|nested] 32+ messages in thread