From: Don Brace <don.brace@pmcs.com>
To: scott.teel@pmcs.com, Kevin.Barnett@pmcs.com,
james.bottomley@parallels.com, hch@infradead.org,
Justin.Lindley@pmcs.com, brace@pmcs.com
Cc: linux-scsi@vger.kernel.org
Subject: [PATCH v5 38/42] hpsa: use scsi host_no as hpsa controller number
Date: Thu, 23 Apr 2015 09:35:09 -0500 [thread overview]
Message-ID: <20150423143509.18832.60585.stgit@brunhilda> (raw)
In-Reply-To: <20150423141637.18832.35621.stgit@brunhilda>
From: Robert Elliott <elliott@hp.com>
Rather than numbering the hpsa controllers with an
incrementing 0..n value (e.g., that shows up in
/proc/interrupts), use the scsi midlayer
host_no (e.g. matching /sys/class/scsi_host/hostNN).
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
---
drivers/scsi/hpsa.c | 134 ++++++++++++++++++++++++++++-----------------------
1 file changed, 74 insertions(+), 60 deletions(-)
diff --git a/drivers/scsi/hpsa.c b/drivers/scsi/hpsa.c
index 674d55a..7b82c67 100644
--- a/drivers/scsi/hpsa.c
+++ b/drivers/scsi/hpsa.c
@@ -324,32 +324,35 @@ static int check_for_unit_attention(struct ctlr_info *h,
switch (asc) {
case STATE_CHANGED:
dev_warn(&h->pdev->dev,
- HPSA "%d: a state change detected, command retried\n",
- h->ctlr);
+ "%s: a state change detected, command retried\n",
+ h->devname);
break;
case LUN_FAILED:
dev_warn(&h->pdev->dev,
- HPSA "%d: LUN failure detected\n", h->ctlr);
+ "%s: LUN failure detected\n", h->devname);
break;
case REPORT_LUNS_CHANGED:
dev_warn(&h->pdev->dev,
- HPSA "%d: report LUN data changed\n", h->ctlr);
+ "%s: report LUN data changed\n", h->devname);
/*
* Note: this REPORT_LUNS_CHANGED condition only occurs on the external
* target (array) devices.
*/
break;
case POWER_OR_RESET:
- dev_warn(&h->pdev->dev, HPSA "%d: a power on "
- "or device reset detected\n", h->ctlr);
+ dev_warn(&h->pdev->dev,
+ "%s: a power on or device reset detected\n",
+ h->devname);
break;
case UNIT_ATTENTION_CLEARED:
- dev_warn(&h->pdev->dev, HPSA "%d: unit attention "
- "cleared by another initiator\n", h->ctlr);
+ dev_warn(&h->pdev->dev,
+ "%s: unit attention cleared by another initiator\n",
+ h->devname);
break;
default:
- dev_warn(&h->pdev->dev, HPSA "%d: unknown "
- "unit attention detected\n", h->ctlr);
+ dev_warn(&h->pdev->dev,
+ "%s: unknown unit attention detected\n",
+ h->devname);
break;
}
return 1;
@@ -4764,22 +4767,16 @@ static int hpsa_scan_finished(struct Scsi_Host *sh,
return finished;
}
-static void hpsa_unregister_scsi(struct ctlr_info *h)
-{
- /* we are being forcibly unloaded, and may not refuse. */
- scsi_remove_host(h->scsi_host);
- scsi_host_put(h->scsi_host);
- h->scsi_host = NULL;
-}
-
-static int hpsa_register_scsi(struct ctlr_info *h)
+static int hpsa_scsi_host_alloc(struct ctlr_info *h)
{
struct Scsi_Host *sh;
int error;
sh = scsi_host_alloc(&hpsa_driver_template, sizeof(h));
- if (sh == NULL)
- goto fail;
+ if (sh == NULL) {
+ dev_err(&h->pdev->dev, "scsi_host_alloc failed\n");
+ return -ENOMEM;
+ }
sh->io_port = 0;
sh->n_io_port = 0;
@@ -4791,7 +4788,6 @@ static int hpsa_register_scsi(struct ctlr_info *h)
sh->can_queue = h->nr_cmds - HPSA_NRESERVED_CMDS;
sh->cmd_per_lun = sh->can_queue;
sh->sg_tablesize = h->maxsgentries;
- h->scsi_host = sh;
sh->hostdata[0] = (unsigned long) h;
sh->irq = h->intr[h->intr_mode];
sh->unique_id = sh->irq;
@@ -4800,24 +4796,24 @@ static int hpsa_register_scsi(struct ctlr_info *h)
dev_err(&h->pdev->dev,
"%s: scsi_init_shared_tag_map failed for controller %d\n",
__func__, h->ctlr);
- goto fail_host_put;
- }
- error = scsi_add_host(sh, &h->pdev->dev);
- if (error) {
- dev_err(&h->pdev->dev, "%s: scsi_add_host failed for controller %d\n",
- __func__, h->ctlr);
- goto fail_host_put;
+ scsi_host_put(sh);
+ return error;
}
- scsi_scan_host(sh);
+ h->scsi_host = sh;
return 0;
+}
- fail_host_put:
- scsi_host_put(sh);
- return error;
- fail:
- dev_err(&h->pdev->dev, "%s: scsi_host_alloc"
- " failed for controller %d\n", __func__, h->ctlr);
- return -ENOMEM;
+static int hpsa_scsi_add_host(struct ctlr_info *h)
+{
+ int rv;
+
+ rv = scsi_add_host(h->scsi_host, &h->pdev->dev);
+ if (rv) {
+ dev_err(&h->pdev->dev, "scsi_add_host failed\n");
+ return rv;
+ }
+ scsi_scan_host(h->scsi_host);
+ return 0;
}
/*
@@ -7489,7 +7485,9 @@ static void hpsa_undo_allocations_after_kdump_soft_reset(struct ctlr_info *h)
hpsa_free_sg_chain_blocks(h); /* init_one 6 */
hpsa_free_cmd_pool(h); /* init_one 5 */
hpsa_free_irqs(h); /* init_one 4 */
- hpsa_free_pci_init(h); /* init_one 3 */
+ scsi_host_put(h->scsi_host); /* init_one 3 */
+ h->scsi_host = NULL; /* init_one 3 */
+ hpsa_free_pci_init(h); /* init_one 2_5 */
free_percpu(h->lockup_detected); /* init_one 2 */
h->lockup_detected = NULL; /* init_one 2 */
if (h->resubmit_wq) {
@@ -7792,9 +7790,15 @@ reinit_after_soft_reset:
rc = hpsa_pci_init(h);
if (rc)
- goto clean2; /* lockup, aer/h */
+ goto clean2; /* lu, aer/h */
+
+ /* relies on h-> settings made by hpsa_pci_init, including
+ * interrupt_mode h->intr */
+ rc = hpsa_scsi_host_alloc(h);
+ if (rc)
+ goto clean2_5; /* pci, lu, aer/h */
- sprintf(h->devname, HPSA "%d", number_of_controllers);
+ sprintf(h->devname, HPSA "%d", h->scsi_host->host_no);
h->ctlr = number_of_controllers;
number_of_controllers++;
@@ -7808,7 +7812,7 @@ reinit_after_soft_reset:
dac = 0;
} else {
dev_err(&pdev->dev, "no suitable DMA available\n");
- goto clean3; /* pci, lockup, aer/h */
+ goto clean3; /* shost, pci, lu, aer/h */
}
}
@@ -7817,13 +7821,13 @@ reinit_after_soft_reset:
rc = hpsa_request_irqs(h, do_hpsa_intr_msi, do_hpsa_intr_intx);
if (rc)
- goto clean3; /* pci, lockup, aer/h */
+ goto clean3; /* shost, pci, lu, aer/h */
rc = hpsa_alloc_cmd_pool(h);
if (rc)
- goto clean4; /* irq, pci, lockup, aer/h */
+ goto clean4; /* irq, shost, pci, lu, aer/h */
rc = hpsa_alloc_sg_chain_blocks(h);
if (rc)
- goto clean5; /* cmd, irq, pci, lockup, aer/h */
+ goto clean5; /* cmd, irq, shost, pci, lu, aer/h */
init_waitqueue_head(&h->scan_wait_queue);
init_waitqueue_head(&h->abort_cmd_wait_queue);
init_waitqueue_head(&h->abort_sync_wait_queue);
@@ -7832,11 +7836,16 @@ reinit_after_soft_reset:
pci_set_drvdata(pdev, h);
h->ndevices = 0;
h->hba_mode_enabled = 0;
- h->scsi_host = NULL;
+
spin_lock_init(&h->devlock);
rc = hpsa_put_ctlr_into_performant_mode(h);
if (rc)
- goto clean6; /* sg, cmd, irq, pci, lockup, aer/h */
+ goto clean6; /* sg, cmd, irq, shost, pci, lu, aer/h */
+
+ /* hook into SCSI subsystem */
+ rc = hpsa_scsi_add_host(h);
+ if (rc)
+ goto clean7; /* perf, sg, cmd, irq, shost, pci, lu, aer/h */
/* create the resubmit workqueue */
h->rescan_ctlr_wq = hpsa_create_controller_wq(h, "rescan");
@@ -7891,7 +7900,7 @@ reinit_after_soft_reset:
rc = hpsa_kdump_soft_reset(h);
if (rc)
/* Neither hard nor soft reset worked, we're hosed. */
- goto clean8;
+ goto clean9;
dev_info(&h->pdev->dev, "Board READY.\n");
dev_info(&h->pdev->dev,
@@ -7926,9 +7935,6 @@ reinit_after_soft_reset:
h->access.set_intr_mask(h, HPSA_INTR_ON);
hpsa_hba_inquiry(h);
- rc = hpsa_register_scsi(h); /* hook ourselves into SCSI subsystem */
- if (rc)
- goto clean8; /* wq, perf, sg, cmd, irq, pci, lockup, aer/h */
/* Monitor the controller for firmware lockups */
h->heartbeat_sample_interval = HEARTBEAT_SAMPLE_INTERVAL;
@@ -7940,20 +7946,23 @@ reinit_after_soft_reset:
h->heartbeat_sample_interval);
return 0;
-clean8: /* perf, sg, cmd, irq, pci, lockup, aer/h */
+clean9: /* wq, sh, perf, sg, cmd, irq, shost, pci, lu, aer/h */
kfree(h->hba_inquiry_data);
-clean7: /* perf, sg, cmd, irq, pci, lockup, aer/h */
+clean7: /* perf, sg, cmd, irq, shost, pci, lu, aer/h */
hpsa_free_performant_mode(h);
h->access.set_intr_mask(h, HPSA_INTR_OFF);
clean6: /* sg, cmd, irq, pci, lockup, wq/aer/h */
hpsa_free_sg_chain_blocks(h);
-clean5: /* cmd, irq, pci, lockup, aer/h */
+clean5: /* cmd, irq, shost, pci, lu, aer/h */
hpsa_free_cmd_pool(h);
-clean4: /* irq, pci, lockup, aer/h */
+clean4: /* irq, shost, pci, lu, aer/h */
hpsa_free_irqs(h);
-clean3: /* pci, lockup, aer/h */
+clean3: /* shost, pci, lu, aer/h */
+ scsi_host_put(h->scsi_host);
+ h->scsi_host = NULL;
+clean2_5: /* pci, lu, aer/h */
hpsa_free_pci_init(h);
-clean2: /* lockup, aer/h */
+clean2: /* lu, aer/h */
if (h->lockup_detected) {
free_percpu(h->lockup_detected);
h->lockup_detected = NULL;
@@ -8052,17 +8061,22 @@ static void hpsa_remove_one(struct pci_dev *pdev)
hpsa_free_device_info(h); /* scan */
- hpsa_unregister_scsi(h); /* init_one 9 */
- kfree(h->hba_inquiry_data); /* init_one 9 */
- h->hba_inquiry_data = NULL; /* init_one 9 */
+ kfree(h->hba_inquiry_data); /* init_one 10 */
+ h->hba_inquiry_data = NULL; /* init_one 10 */
+ if (h->scsi_host)
+ scsi_remove_host(h->scsi_host); /* init_one 8 */
+ hpsa_free_ioaccel2_sg_chain_blocks(h);
hpsa_free_performant_mode(h); /* init_one 7 */
hpsa_free_sg_chain_blocks(h); /* init_one 6 */
hpsa_free_cmd_pool(h); /* init_one 5 */
/* hpsa_free_irqs already called via hpsa_shutdown init_one 4 */
+ scsi_host_put(h->scsi_host); /* init_one 3 */
+ h->scsi_host = NULL; /* init_one 3 */
+
/* includes hpsa_disable_interrupt_mode - pci_init 2 */
- hpsa_free_pci_init(h); /* init_one 3 */
+ hpsa_free_pci_init(h); /* init_one 2.5 */
free_percpu(h->lockup_detected); /* init_one 2 */
h->lockup_detected = NULL; /* init_one 2 */
next prev parent reply other threads:[~2015-04-23 14:36 UTC|newest]
Thread overview: 44+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-04-23 14:31 [PATCH v5 00/42] hpsa updates Don Brace
2015-04-23 14:31 ` [PATCH v5 01/42] hpsa: add masked physical devices into h->dev[] array Don Brace
2015-04-23 14:31 ` [PATCH v5 02/42] hpsa: clean up host, channel, target, lun prints Don Brace
2015-04-23 14:32 ` [PATCH v5 03/42] hpsa: rework controller command submission Don Brace
2015-04-23 14:32 ` [PATCH v5 04/42] hpsa: clean up aborts Don Brace
2015-04-23 14:32 ` [PATCH v5 05/42] hpsa: decrement h->commands_outstanding in fail_all_outstanding_cmds Don Brace
2015-04-23 14:32 ` [PATCH v5 06/42] hpsa: hpsa decode sense data for io and tmf Don Brace
2015-04-23 14:32 ` [PATCH v5 07/42] hpsa: allow lockup detected to be viewed via sysfs Don Brace
2015-04-23 14:32 ` [PATCH v5 08/42] hpsa: make function names consistent Don Brace
2015-04-23 14:32 ` [PATCH v5 09/42] hpsa: factor out hpsa_init_cmd function Don Brace
2015-04-23 14:32 ` [PATCH v5 10/42] hpsa: do not ignore return value of hpsa_register_scsi Don Brace
2015-04-23 14:32 ` [PATCH v5 11/42] hpsa: try resubmitting down raid path on task set full Don Brace
2015-04-23 14:32 ` [PATCH v5 12/42] hpsa: factor out hpsa_ioaccel_submit function Don Brace
2015-04-23 14:32 ` [PATCH v5 13/42] hpsa: print accurate SSD Smart Path Enabled status Don Brace
2015-04-23 14:32 ` [PATCH v5 14/42] hpsa: use ioaccel2 path to submit IOs to physical drives in HBA mode Don Brace
2015-04-23 14:33 ` [PATCH v5 15/42] hpsa: Get queue depth from identify physical bmic for physical disks Don Brace
2015-04-23 14:33 ` [PATCH v5 16/42] hpsa: break hpsa_free_irqs_and_disable_msix into two functions Don Brace
2015-04-23 14:33 ` [PATCH v5 17/42] hpsa: clean up error handling Don Brace
2015-04-23 14:33 ` [PATCH v5 18/42] hpsa: refactor freeing of resources into more logical functions Don Brace
2015-04-23 14:33 ` [PATCH v5 19/42] hpsa: add ioaccel sg chaining for the ioaccel2 path Don Brace
2015-04-23 14:33 ` [PATCH v5 20/42] hpsa: add more ioaccel2 error handling, including underrun statuses Don Brace
2015-04-23 14:33 ` [PATCH v5 21/42] hpsa: do not check cmd_alloc return value - it cannnot return NULL Don Brace
2015-04-23 14:33 ` [PATCH v5 22/42] hpsa: correct return values from driver functions Don Brace
2015-04-23 14:33 ` [PATCH v5 23/42] hpsa: clean up driver init Don Brace
2015-04-23 14:33 ` [PATCH v5 24/42] hpsa: clean up some error reporting output in abort handler Don Brace
2015-04-23 14:34 ` [PATCH v5 25/42] hpsa: do not print ioaccel2 warning messages about unusual completions Don Brace
2015-04-23 14:34 ` [PATCH v5 26/42] hpsa: add support sending aborts to physical devices via the ioaccel2 path Don Brace
2015-04-23 14:34 ` [PATCH v5 27/42] hpsa: use helper routines for finishing commands Don Brace
2015-04-23 14:34 ` [PATCH v5 28/42] hpsa: don't return abort request until target is complete Don Brace
2015-04-23 14:34 ` [PATCH v5 29/42] hpsa: refactor and rework support for sending TEST_UNIT_READY Don Brace
2015-04-23 14:34 ` [PATCH v5 30/42] hpsa: performance tweak for hpsa_scatter_gather() Don Brace
2015-04-23 14:34 ` [PATCH v5 31/42] hpsa: call pci_release_regions after pci_disable_device Don Brace
2015-04-23 14:34 ` [PATCH v5 32/42] hpsa: skip free_irq calls if irqs are not allocated Don Brace
2015-04-23 14:34 ` [PATCH v5 33/42] hpsa: cleanup for init_one step 2 in kdump Don Brace
2015-04-23 14:34 ` [PATCH v5 34/42] hpsa: fix try_soft_reset error handling Don Brace
2015-04-23 14:34 ` [PATCH v5 35/42] hpsa: create workqueue after the driver is ready for use Don Brace
2015-04-23 14:34 ` [PATCH v5 36/42] hpsa: add interrupt number to /proc/interrupts interrupt name Don Brace
2015-04-23 14:35 ` [PATCH v5 37/42] hpsa: use block layer tag for command allocation Don Brace
2015-04-23 14:35 ` Don Brace [this message]
2015-04-23 14:35 ` [PATCH v5 39/42] hpsa: propagate the error code in hpsa_kdump_soft_reset Don Brace
2015-04-23 14:35 ` [PATCH v5 40/42] hpsa: cleanup reset Don Brace
2015-04-23 14:35 ` [PATCH v5 41/42] hpsa: add in new controller id Don Brace
2015-04-23 14:35 ` [PATCH v5 42/42] hpsa: change driver version Don Brace
2015-05-11 9:13 ` [PATCH v5 00/42] hpsa updates Christoph Hellwig
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20150423143509.18832.60585.stgit@brunhilda \
--to=don.brace@pmcs.com \
--cc=Justin.Lindley@pmcs.com \
--cc=Kevin.Barnett@pmcs.com \
--cc=brace@pmcs.com \
--cc=hch@infradead.org \
--cc=james.bottomley@parallels.com \
--cc=linux-scsi@vger.kernel.org \
--cc=scott.teel@pmcs.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox