From: sashiko-bot@kernel.org
To: "Srinivas Kandagatla" <srinivas.kandagatla@oss.qualcomm.com>
Cc: linux-sound@vger.kernel.org, devicetree@vger.kernel.org,
robh@kernel.org, conor+dt@kernel.org
Subject: Re: [PATCH v2 12/24] ASoC: qcom: audioreach: cache VI calibration results per speaker
Date: Sun, 22 Nov 2026 16:22:33 +0000 [thread overview]
Message-ID: <sashiko-outbox-228094@kernel.org> (raw)
In-Reply-To: <20261122161437.5994-13-srinivas.kandagatla@oss.qualcomm.com>
Thank you for your contribution! Sashiko AI review found 2 potential
issues to consider:
- [Medium] ASoC: qcom: false success on num_ch == 0 in
audioreach_vi_calibration_event()
- [Low] ASoC: qcom: negative Q24 misformatting in
sp_vi_q24_to_int_frac()
--
commit cfc96c13af943af3459ead6b6b605460ffdd651e
Author: Ravi Hothi <ravi.hothi@oss.qualcomm.com>
ASoC: qcom: audioreach: cache VI calibration results per speaker
This commit adds a mutex-protected per-speaker cache for VI calibration
events to log state transitions once per speaker and store measured R0
values when calibration completes.
> diff --git a/sound/soc/qcom/qdsp6/audioreach.c b/sound/soc/qcom/qdsp6/audioreach.c
> index fbb9e3c4b84ae..2b5c083b8ae56 100644
> --- a/sound/soc/qcom/qdsp6/audioreach.c
> +++ b/sound/soc/qcom/qdsp6/audioreach.c
[ ... ]
> @@ -1462,16 +1482,112 @@ static int audioreach_gain_set(struct q6apm_graph *graph,
> return q6apm_send_cmd_sync(graph->apm, pkt, 0);
> }
[ ... ]
> +static int sp_vi_q24_to_int_frac(s32 val, int *frac)
> +{
> + *frac = (int)(((s64)(val & 0xffffff) * 1000) >> 24);
> +
> + return val >> 24;
> +}
[Severity: Low]
Does sp_vi_q24_to_int_frac() misformat negative Q24 values when an
out-of-range negative R0 is logged? Because val is signed, val >> 24
floors toward negative infinity and val & 0xffffff extracts the positive
two's-complement offset above that floor, so -0.25 ohms (-4194304) prints
as -1.750 ohms instead of -0.250 ohms.
> void audioreach_vi_calibration_event(struct device *dev,
> const struct event_id_vi_per_spkr_calibration *cali,
> u32 num_ch)
> {
> + bool decisive = true;
> + bool success = true;
> unsigned int i;
> + u32 bit;
> +
> + guard(mutex)(&sp_vi_r0_lock);
> +
> + if (!sp_vi_r0.armed)
> + return;
> +
> + /* First event of this run: drop the previous result */
> + if (!memchr_inv(sp_vi_r0.seen_states, 0, sizeof(sp_vi_r0.seen_states))) {
> + sp_vi_r0.state = SP_VI_CALI_RUNNING;
> + sp_vi_r0.num_ch = 0;
> + memset(sp_vi_r0.r0_cali_q24, 0, sizeof(sp_vi_r0.r0_cali_q24));
> + }
> +
> + for (i = 0; i < num_ch; i++) {
> u32 state = cali->cali_param[i].state;
>
> - /* Raised every frame; keep the per-event log at debug level */
> - for (i = 0; i < num_ch; i++)
> - dev_dbg(dev, "VI calibration channel %u: state %u\n",
> - i, cali->cali_param[i].state);
> + if (sp_vi_cali_state_is_failure(state))
> + success = false;
> + else if (!sp_vi_cali_state_is_terminal(state))
> + decisive = false;
> +
> + bit = BIT(min_t(u32, state, SP_VI_CALI_UNKNOWN_STATE_BIT));
> + if (!(sp_vi_r0.seen_states[i] & bit)) {
> + sp_vi_r0.seen_states[i] |= bit;
> + dev_info(dev, "VI calibration channel %u: %s\n",
> + i, sp_vi_cali_state_name(state));
> + }
> + }
> +
> + if (!decisive)
> + return;
> +
> + sp_vi_r0.armed = false;
> + sp_vi_r0.state = success ? SP_VI_CALI_SUCCESS : SP_VI_CALI_FAILED;
> + sp_vi_r0.num_ch = num_ch;
[Severity: Medium]
What happens if q6apm_vi_calibration_event() passes num_ch == 0 (for
instance, if cali->num_ch is 0 or the event payload has no cali_param
entries)? Because decisive and success start as true and the loop does
not run, audioreach_vi_calibration_event() wipes the previous cached
result, disarms sp_vi_r0.armed so later events are ignored, and records
SP_VI_CALI_SUCCESS with sp_vi_r0.num_ch = 0.
--
Sashiko AI review · https://sashiko.dev/#/patchset/20261122161437.5994-1-srinivas.kandagatla@oss.qualcomm.com?part=12
next prev parent reply other threads:[~2026-11-22 16:22 UTC|newest]
Thread overview: 82+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-10-23 17:14 [RFC PATCH 00/23] ASoC: qcom: AudioReach Active speaker protection for WSA884x Srinivas Kandagatla
2026-10-23 17:14 ` [RFC PATCH 01/23] ASoC: soc-core: allow default ch_maps on links with more than 8 DAIs Srinivas Kandagatla
2026-11-15 17:36 ` Mark Brown
2026-11-15 21:04 ` Srinivas Kandagatla
2026-10-23 17:14 ` [RFC PATCH 02/23] ASoC: soc-pcm: add multi_direction_codecs link flag Srinivas Kandagatla
2026-11-15 17:36 ` Mark Brown
2026-11-15 21:04 ` Srinivas Kandagatla
2026-10-23 17:14 ` [RFC PATCH 03/23] ASoC: qcom: sdw: add per-direction stream runtimes for multi_direction links Srinivas Kandagatla
2026-11-15 17:36 ` Mark Brown
2026-11-15 21:04 ` Srinivas Kandagatla
2026-10-23 17:14 ` [RFC PATCH 04/23] ASoC: dt-bindings: qcom,wsa8840: allow one sound DAI cell Srinivas Kandagatla
2026-10-23 17:14 ` [RFC PATCH 05/23] ASoC: codecs: wsa884x: add VI sense capture DAI Srinivas Kandagatla
2026-11-15 17:36 ` Mark Brown
2026-11-15 21:03 ` Srinivas Kandagatla
2026-10-23 17:14 ` [RFC PATCH 06/23] ASoC: codecs: wsa884x: register the die temperature as a thermal zone Srinivas Kandagatla
2026-10-23 17:14 ` [RFC PATCH 07/23] ASoC: qcom: audioreach: add control link support to graphs Srinivas Kandagatla
2026-10-23 17:14 ` [RFC PATCH 08/23] ASoC: qcom: audioreach: run VI module in calibration mode with per-speaker events Srinivas Kandagatla
2026-11-15 17:36 ` Mark Brown
2026-11-15 21:04 ` Srinivas Kandagatla
2026-10-23 17:14 ` [RFC PATCH 09/23] ASoC: qcom: q6apm-dai: add S32_LE format support Srinivas Kandagatla
2026-10-23 17:14 ` [RFC PATCH 10/23] ASoC: qcom: audioreach: support up to four speakers in VI feedback Srinivas Kandagatla
2026-10-23 17:14 ` [RFC PATCH 11/23] ASoC: qcom: audioreach: cache VI calibration results per speaker Srinivas Kandagatla
2026-10-23 17:14 ` [RFC PATCH 12/23] ASoC: qcom: audioreach: make the speaker protection operation mode configurable Srinivas Kandagatla
2026-10-23 17:14 ` [RFC PATCH 13/23] ASoC: qcom: audioreach: send cached R0/T0 to the VI module in normal mode Srinivas Kandagatla
2026-10-23 17:14 ` [RFC PATCH 14/23] ASoC: qcom: audioreach: send static cfg blobs to speaker protection modules Srinivas Kandagatla
2026-10-23 17:14 ` [RFC PATCH 15/23] ASoC: qcom: audioreach: add speaker protection mixer controls Srinivas Kandagatla
2026-10-23 17:14 ` [RFC PATCH 16/23] ASoC: qcom: audioreach: pin SPEAKER_PROTECTION_VI media format Srinivas Kandagatla
2026-10-23 17:14 ` [RFC PATCH 17/23] ASoC: qcom: audioreach: add live speaker temperature (T0) readback Srinivas Kandagatla
2026-10-23 17:14 ` [RFC PATCH 18/23] ASoC: qcom: audioreach: add speaker protection calibration state control Srinivas Kandagatla
2026-10-23 17:14 ` [RFC PATCH 19/23] ASoC: qcom: audioreach: keep the last VI calibration result until the DSP reports Srinivas Kandagatla
2026-10-23 17:14 ` [RFC PATCH 20/23] ASoC: qcom: x1e80100: carry WSA VI feedback on the WSA Playback BE link Srinivas Kandagatla
2026-11-15 17:36 ` Mark Brown
2026-11-15 21:03 ` Srinivas Kandagatla
2026-10-23 17:14 ` [RFC PATCH 21/23] ASoC: qcom: x1e80100: register WSA speaker thermal zones for speaker protection Srinivas Kandagatla
2026-10-23 17:14 ` [RFC PATCH 22/23] arm64: dts: qcom: glymur-crd: add WSA speaker protection VI feedback Srinivas Kandagatla
2026-10-28 13:38 ` Konrad Dybcio
2026-10-28 21:59 ` Srinivas Kandagatla
2026-10-29 8:17 ` Konrad Dybcio
2026-10-23 17:14 ` [RFC PATCH 23/23] arm64: dts: qcom: mahua-t14s: " Srinivas Kandagatla
2026-10-28 12:39 ` [RFC PATCH 00/23] ASoC: qcom: AudioReach Active speaker protection for WSA884x Mark Brown
2026-10-28 16:31 ` Fabian Renn-Giles
2026-10-28 21:56 ` Srinivas Kandagatla
2026-11-15 22:07 ` Srinivas Kandagatla
2026-11-22 16:14 ` [PATCH v2 00/24] ASoC: qcom: AudioReach Active speaker protection for WSA88xx Srinivas Kandagatla
2026-11-22 16:14 ` [PATCH v2 01/24] ASoC: soc-core: always allocate default ch_maps Srinivas Kandagatla
2026-11-22 16:31 ` sashiko-bot
2026-11-22 16:14 ` [PATCH v2 02/24] ASoC: soc-pcm: add multi_direction_codecs link flag Srinivas Kandagatla
2026-11-22 16:14 ` [PATCH v2 03/24] ASoC: soc-dai: export snd_soc_dai_stream_valid Srinivas Kandagatla
2026-11-22 16:14 ` [PATCH v2 04/24] ASoC: qcom: sdw: add per-direction stream runtimes for multi_direction links Srinivas Kandagatla
2026-11-22 16:38 ` sashiko-bot
2026-11-22 16:14 ` [PATCH v2 05/24] ASoC: dt-bindings: qcom,wsa8840: allow one sound DAI cell Srinivas Kandagatla
2026-11-22 16:14 ` [PATCH v2 06/24] ASoC: codecs: wsa884x: add VI sense capture DAI Srinivas Kandagatla
2026-11-22 16:28 ` sashiko-bot
2026-11-22 16:14 ` [PATCH v2 07/24] ASoC: codecs: wsa883x: " Srinivas Kandagatla
2026-11-22 16:28 ` sashiko-bot
2026-11-22 16:14 ` [PATCH v2 08/24] ASoC: codecs: wsa884x: register the die temperature as a thermal zone Srinivas Kandagatla
2026-11-22 16:28 ` sashiko-bot
2026-11-22 16:14 ` [PATCH v2 09/24] ASoC: qcom: audioreach: add control link support to graphs Srinivas Kandagatla
2026-11-22 16:32 ` sashiko-bot
2026-11-22 16:14 ` [PATCH v2 10/24] ASoC: qcom: audioreach: run VI module in calibration mode with per-speaker events Srinivas Kandagatla
2026-11-22 16:14 ` [PATCH v2 11/24] ASoC: qcom: q6apm-dai: add S32_LE format support Srinivas Kandagatla
2026-11-22 16:14 ` [PATCH v2 12/24] ASoC: qcom: audioreach: cache VI calibration results per speaker Srinivas Kandagatla
2026-11-22 16:22 ` sashiko-bot [this message]
2026-11-22 16:14 ` [PATCH v2 13/24] ASoC: qcom: audioreach: add speaker protection calibration trigger infrastructure Srinivas Kandagatla
2026-11-22 16:31 ` sashiko-bot
2026-11-22 16:14 ` [PATCH v2 14/24] ASoC: qcom: audioreach: send cached R0/T0 to the VI module in normal mode Srinivas Kandagatla
2026-11-22 16:28 ` sashiko-bot
2026-11-22 16:14 ` [PATCH v2 15/24] ASoC: qcom: audioreach: send static cfg blobs to speaker protection modules Srinivas Kandagatla
2026-11-22 16:31 ` sashiko-bot
2026-11-22 16:14 ` [PATCH v2 16/24] ASoC: qcom: audioreach: add speaker protection mixer controls Srinivas Kandagatla
2026-11-22 16:14 ` [PATCH v2 17/24] ASoC: qcom: audioreach: pin SPEAKER_PROTECTION_VI media format Srinivas Kandagatla
2026-11-22 16:14 ` [PATCH v2 18/24] ASoC: qcom: audioreach: add live speaker temperature (T0) readback Srinivas Kandagatla
2026-11-22 16:37 ` sashiko-bot
2026-11-22 16:14 ` [PATCH v2 19/24] ASoC: qcom: audioreach: add speaker protection calibration state control Srinivas Kandagatla
2026-11-22 16:37 ` sashiko-bot
2026-11-22 16:14 ` [PATCH v2 20/24] ASoC: qcom: x1e80100: carry WSA VI feedback on the WSA Playback BE link Srinivas Kandagatla
2026-11-22 16:14 ` [PATCH v2 21/24] ASoC: qcom: x1e80100: register WSA speaker thermal zones for speaker protection Srinivas Kandagatla
2026-11-22 16:14 ` [PATCH v2 22/24] arm64: dts: qcom: glymur-crd: add WSA speaker protection VI feedback Srinivas Kandagatla
2026-11-22 16:39 ` sashiko-bot
2026-11-22 16:14 ` [PATCH v2 23/24] arm64: dts: qcom: mahua-t14s: " Srinivas Kandagatla
2026-11-22 16:14 ` [PATCH v2 24/24] arm64: dts: qcom: x1e78100-t14s: " Srinivas Kandagatla
2026-11-22 16:37 ` sashiko-bot
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=sashiko-outbox-228094@kernel.org \
--to=sashiko-bot@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-sound@vger.kernel.org \
--cc=robh@kernel.org \
--cc=sashiko-reviews@lists.linux.dev \
--cc=srinivas.kandagatla@oss.qualcomm.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox