* [PATCH net v3 00/10] net: au1000: Bug fixes
@ 2026-11-17 19:32 Florian Fainelli
2026-11-17 19:32 ` [PATCH net v3 01/10] net: au1000: recycle RX descriptors on allocation failure Florian Fainelli
` (10 more replies)
0 siblings, 11 replies; 12+ messages in thread
From: Florian Fainelli @ 2026-11-17 19:32 UTC (permalink / raw)
To: netdev
Cc: Florian Fainelli, Andrew Lunn, David S. Miller, Eric Dumazet,
Jakub Kicinski, Paolo Abeni, Heiner Kallweit, Russell King,
Jijie Shao, Simon Horman, Runyu Xiao, David Yang,
Herbert Valerio Riedel, Danny Kukawka, Mugunthan V N,
Sebastian Hesselbarth, open list, Manuel Lauss
This series fixes RX descriptor recycling, receive filtering, MDIO error
reporting, TX ring synchronization, MAC/PHY lifecycle ordering, and TX
bounce-buffer bounds in the Au1xxx Ethernet driver. It also adds the
LAN83C183 PHY resume delay needed for MII clock recovery on the MTX-1.
Changes in v3:
- Drop the no-platform-data MAC-address patch: in-tree platform devices
always supply platform data, so this is defensive hardening rather
than a fix for an in-tree configuration.
- Drop the buffer descriptor free-list insertion patch: the affected
list is only rebuilt during teardown and is never consumed again.
The series now contains 10 patches instead of 12.
- Distinguish MDIO write-completion timeouts from pre-write busy
timeouts in the diagnostic message.
- Clarify that the LAN83C183 recovery-delay patch and the following
au1000 MAC/PHY sequencing patch are both required to fix MTX-1 reopen.
Keep the PHY patch first so its delay is available to the MAC fix.
- Remove the unreachable initialization-error branch and PHY rollback
from au1000_open(). Correct the commit message to distinguish the new
synchronous PHY resume from the existing initialization-before-
phy_start() ordering, and reconcile the reset comments.
- Expand the TX bounds-check commit message to cover plain AF_PACKET
sendmsg(), PACKET_TX_RING, and oversized software-GSO segments.
- Rebuild the kernel and root filesystem and repeat MTX-1 regression
testing after the review changes.
Changes in v2:
- Rebase onto net.
- Reset the MAC after PHY/MDIO teardown, and avoid MAC control accesses
when its clock is already disabled.
- Use sleepable polling for MDIO write completion.
- Advance tx_tail when submission reclaims a completed TX descriptor,
and consume transmitted skbs outside the lock with an IRQ-safe helper.
- Restore receive filtering before enabling RX, with the address-list
and device locks held to keep the programmed filter consistent.
- Resume the PHY synchronously before MAC initialization, clear cached
link state on open, and use acknowledged link/duplex state under the
device lock. Place the LAN83C183 recovery-delay patch before this fix.
- Add a TX length check to prevent overflowing the DMA bounce buffer.
Testing:
The current series was rebuilt with Buildroot and tested on a Meshcube
MTX-1, using the Alchemy PROM Ethernet-address lifetime fix as a separate
boot prerequisite. That prerequisite is not included in this series.
All 11 boot-smoke checks passed, including 15 down/up cycles across
normal, promiscuous and all-multicast modes, removal/rebind after an
opened/closed interface and a never-opened interface, and connectivity
recovery. No kernel findings were reported. The final 10-packet ping
lost one reply; a subsequent 100-packet test had zero loss. The cause of
the isolated loss was not established.
These hardware tests cover boot and Ethernet lifecycle behavior; full
AF_PACKET overflow triggers and fault injection were not exercised.
Sashiko AI review identified issues addressed in the revisions. OpenAI
Codex assisted source analysis, code and changelog revisions, patch
consolidation, and regression testing.
Florian Fainelli (10):
net: au1000: recycle RX descriptors on allocation failure
net: au1000: clear all-multicast mode when restoring hash filtering
net: au1000: disconnect the PHY before freeing the MDIO bus
net: au1000: report MDIO transaction timeouts
net: au1000: serialize TX completion with packet submission
net: au1000: restore receive filtering before enabling RX
net: au1000: restore RX buffer addresses when restarting the MAC
net: phy: smsc: wait for LAN83C183 power-down recovery
net: au1000: keep the MAC stopped until the PHY link is ready
net: au1000: reject frames larger than the TX bounce buffer
drivers/net/ethernet/amd/au1000_eth.c | 145 +++++++++++++++++++-------
drivers/net/phy/Kconfig | 2 +-
drivers/net/phy/smsc.c | 26 +++++
3 files changed, 133 insertions(+), 40 deletions(-)
base-commit: 145480b28ca82e9fae789427cc4569e596515a32
--
2.53.0
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH net v3 01/10] net: au1000: recycle RX descriptors on allocation failure
2026-11-17 19:32 [PATCH net v3 00/10] net: au1000: Bug fixes Florian Fainelli
@ 2026-11-17 19:32 ` Florian Fainelli
2026-11-17 19:32 ` [PATCH net v3 02/10] net: au1000: clear all-multicast mode when restoring hash filtering Florian Fainelli
` (9 subsequent siblings)
10 siblings, 0 replies; 12+ messages in thread
From: Florian Fainelli @ 2026-11-17 19:32 UTC (permalink / raw)
To: netdev
Cc: Florian Fainelli, Andrew Lunn, David S. Miller, Eric Dumazet,
Jakub Kicinski, Paolo Abeni, Heiner Kallweit, Russell King,
Jijie Shao, Simon Horman, Runyu Xiao, David Yang,
Herbert Valerio Riedel, Danny Kukawka, Mugunthan V N,
Sebastian Hesselbarth, open list, Manuel Lauss
An skb allocation failure retries the same completed descriptor forever
in hard IRQ context. Return the buffer to DMA and advance the ring even
when the packet must be dropped.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
---
drivers/net/ethernet/amd/au1000_eth.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/drivers/net/ethernet/amd/au1000_eth.c b/drivers/net/ethernet/amd/au1000_eth.c
index 8682323d693f..cd25248f4e3a 100644
--- a/drivers/net/ethernet/amd/au1000_eth.c
+++ b/drivers/net/ethernet/amd/au1000_eth.c
@@ -788,7 +788,7 @@ static int au1000_rx(struct net_device *dev)
skb = netdev_alloc_skb(dev, frmlen + 2);
if (!skb) {
dev->stats.rx_dropped++;
- continue;
+ goto next;
}
skb_reserve(skb, 2); /* 16 byte IP header align */
skb_copy_to_linear_data(skb,
@@ -820,6 +820,7 @@ static int au1000_rx(struct net_device *dev)
pr_cont("\n");
}
}
+next:
prxd->buff_stat = lower_32_bits(pDB->dma_addr) | RX_DMA_ENABLE;
aup->rx_head = (aup->rx_head + 1) & (NUM_RX_DMA - 1);
wmb(); /* drain writebuffer */
--
2.53.0
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH net v3 02/10] net: au1000: clear all-multicast mode when restoring hash filtering
2026-11-17 19:32 [PATCH net v3 00/10] net: au1000: Bug fixes Florian Fainelli
2026-11-17 19:32 ` [PATCH net v3 01/10] net: au1000: recycle RX descriptors on allocation failure Florian Fainelli
@ 2026-11-17 19:32 ` Florian Fainelli
2026-11-17 19:32 ` [PATCH net v3 03/10] net: au1000: disconnect the PHY before freeing the MDIO bus Florian Fainelli
` (8 subsequent siblings)
10 siblings, 0 replies; 12+ messages in thread
From: Florian Fainelli @ 2026-11-17 19:32 UTC (permalink / raw)
To: netdev
Cc: Florian Fainelli, Andrew Lunn, David S. Miller, Eric Dumazet,
Jakub Kicinski, Paolo Abeni, Heiner Kallweit, Russell King,
Jijie Shao, Simon Horman, Runyu Xiao, David Yang,
Herbert Valerio Riedel, Danny Kukawka, Mugunthan V N,
Sebastian Hesselbarth, open list, Manuel Lauss
MAC_PASS_ALL_MULTI remains set after IFF_ALLMULTI is cleared or the
multicast list shrinks below the filter limit. Clear it when programming
the selective multicast hash so unwanted multicast traffic is filtered
again.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
---
drivers/net/ethernet/amd/au1000_eth.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/net/ethernet/amd/au1000_eth.c b/drivers/net/ethernet/amd/au1000_eth.c
index cd25248f4e3a..58bc8e1b539d 100644
--- a/drivers/net/ethernet/amd/au1000_eth.c
+++ b/drivers/net/ethernet/amd/au1000_eth.c
@@ -1042,7 +1042,7 @@ static void au1000_multicast_list(struct net_device *dev)
(long *)mc_filter);
writel(mc_filter[1], &aup->mac->multi_hash_high);
writel(mc_filter[0], &aup->mac->multi_hash_low);
- reg &= ~MAC_PROMISCUOUS;
+ reg &= ~(MAC_PROMISCUOUS | MAC_PASS_ALL_MULTI);
reg |= MAC_HASH_MODE;
}
writel(reg, &aup->mac->control);
--
2.53.0
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH net v3 03/10] net: au1000: disconnect the PHY before freeing the MDIO bus
2026-11-17 19:32 [PATCH net v3 00/10] net: au1000: Bug fixes Florian Fainelli
2026-11-17 19:32 ` [PATCH net v3 01/10] net: au1000: recycle RX descriptors on allocation failure Florian Fainelli
2026-11-17 19:32 ` [PATCH net v3 02/10] net: au1000: clear all-multicast mode when restoring hash filtering Florian Fainelli
@ 2026-11-17 19:32 ` Florian Fainelli
2026-11-17 19:32 ` [PATCH net v3 04/10] net: au1000: report MDIO transaction timeouts Florian Fainelli
` (7 subsequent siblings)
10 siblings, 0 replies; 12+ messages in thread
From: Florian Fainelli @ 2026-11-17 19:32 UTC (permalink / raw)
To: netdev
Cc: Florian Fainelli, Andrew Lunn, David S. Miller, Eric Dumazet,
Jakub Kicinski, Paolo Abeni, Heiner Kallweit, Russell King,
Jijie Shao, Simon Horman, Runyu Xiao, David Yang,
Herbert Valerio Riedel, Danny Kukawka, Mugunthan V N,
Sebastian Hesselbarth, open list, Manuel Lauss
Balance phy_connect() on probe failure and removal. Otherwise PHY
interrupts, device references and the attachment to the freed netdev
survive teardown. Disconnect before unregistering the bus while its MDIO
callbacks and MAC registers remain usable.
PHY teardown can re-enable the MAC for MDIO even if the interface was
never opened. Reset the MAC after PHY and MDIO bus teardown, before
releasing descriptors and register mappings. Skip MAC control accesses
when mac_enabled is clear, since stopping an already clock-gated MAC
hangs MTX-1. Always clear the DMA descriptor control bits and TX state.
Fixes: 0638dec01e89 ("[PATCH] net: au1000_eth: PHY framework conversion")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
---
drivers/net/ethernet/amd/au1000_eth.c | 26 +++++++++++++++++---------
1 file changed, 17 insertions(+), 9 deletions(-)
diff --git a/drivers/net/ethernet/amd/au1000_eth.c b/drivers/net/ethernet/amd/au1000_eth.c
index 58bc8e1b539d..7063f9e5bc7c 100644
--- a/drivers/net/ethernet/amd/au1000_eth.c
+++ b/drivers/net/ethernet/amd/au1000_eth.c
@@ -584,14 +584,17 @@ static void au1000_reset_mac_unlocked(struct net_device *dev)
struct au1000_private *const aup = netdev_priv(dev);
int i;
- au1000_hard_stop(dev);
+ if (aup->mac_enabled) {
+ au1000_hard_stop(dev);
- writel(MAC_EN_CLOCK_ENABLE, aup->enable);
- wmb(); /* drain writebuffer */
- mdelay(2);
- writel(0, aup->enable);
- wmb(); /* drain writebuffer */
- mdelay(2);
+ writel(MAC_EN_CLOCK_ENABLE, aup->enable);
+ wmb(); /* drain writebuffer */
+ mdelay(2);
+ writel(0, aup->enable);
+ wmb(); /* drain writebuffer */
+ mdelay(2);
+ aup->mac_enabled = 0;
+ }
aup->tx_full = 0;
for (i = 0; i < NUM_RX_DMA; i++) {
@@ -603,8 +606,6 @@ static void au1000_reset_mac_unlocked(struct net_device *dev)
aup->tx_dma_ring[i]->buff_stat &= ~0xf;
}
- aup->mac_enabled = 0;
-
}
static void au1000_reset_mac(struct net_device *dev)
@@ -1287,6 +1288,8 @@ static int au1000_probe(struct platform_device *pdev)
return 0;
err_out:
+ if (dev->phydev)
+ phy_disconnect(dev->phydev);
if (aup->mii_bus)
mdiobus_unregister(aup->mii_bus);
@@ -1334,9 +1337,14 @@ static void au1000_remove(struct platform_device *pdev)
struct resource *base, *macen;
unregister_netdev(dev);
+ if (dev->phydev)
+ phy_disconnect(dev->phydev);
mdiobus_unregister(aup->mii_bus);
mdiobus_free(aup->mii_bus);
+ /* PHY teardown may have re-enabled the MAC for MDIO accesses. */
+ au1000_reset_mac(dev);
+
for (i = 0; i < NUM_RX_DMA; i++)
if (aup->rx_db_inuse[i])
au1000_ReleaseDB(aup, aup->rx_db_inuse[i]);
--
2.53.0
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH net v3 04/10] net: au1000: report MDIO transaction timeouts
2026-11-17 19:32 [PATCH net v3 00/10] net: au1000: Bug fixes Florian Fainelli
` (2 preceding siblings ...)
2026-11-17 19:32 ` [PATCH net v3 03/10] net: au1000: disconnect the PHY before freeing the MDIO bus Florian Fainelli
@ 2026-11-17 19:32 ` Florian Fainelli
2026-11-17 19:32 ` [PATCH net v3 05/10] net: au1000: serialize TX completion with packet submission Florian Fainelli
` (6 subsequent siblings)
10 siblings, 0 replies; 12+ messages in thread
From: Florian Fainelli @ 2026-11-17 19:32 UTC (permalink / raw)
To: netdev
Cc: Florian Fainelli, Andrew Lunn, David S. Miller, Eric Dumazet,
Jakub Kicinski, Paolo Abeni, Heiner Kallweit, Russell King,
Jijie Shao, Simon Horman, Runyu Xiao, David Yang,
Herbert Valerio Riedel, Danny Kukawka, Mugunthan V N,
Sebastian Hesselbarth, open list, Manuel Lauss
The MDIO write callback reports success even if the controller stays
busy and no write is issued. Propagate timeout errors and wait for write
completion so failure of the final transaction is reported to phylib as
well. Return ETIMEDOUT for read timeouts too.
Use readl_poll_timeout() for write completion with a 20 microsecond sleep
interval and a 20 millisecond timeout. The MDIO callback runs in sleepable
context, so avoid adding millisecond busy-waits for completion.
Fixes: 0638dec01e89 ("[PATCH] net: au1000_eth: PHY framework conversion")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
---
drivers/net/ethernet/amd/au1000_eth.c | 22 +++++++++++++++-------
1 file changed, 15 insertions(+), 7 deletions(-)
diff --git a/drivers/net/ethernet/amd/au1000_eth.c b/drivers/net/ethernet/amd/au1000_eth.c
index 7063f9e5bc7c..1935b1d4b173 100644
--- a/drivers/net/ethernet/amd/au1000_eth.c
+++ b/drivers/net/ethernet/amd/au1000_eth.c
@@ -41,6 +41,7 @@
#include <linux/platform_device.h>
#include <linux/cpu.h>
#include <linux/io.h>
+#include <linux/iopoll.h>
#include <asm/mipsregs.h>
#include <asm/irq.h>
@@ -278,7 +279,7 @@ static int au1000_mdio_read(struct net_device *dev, int phy_addr, int reg)
mdelay(1);
if (--timedout == 0) {
netdev_err(dev, "read_MII busy timeout!!\n");
- return -1;
+ return -ETIMEDOUT;
}
}
@@ -292,26 +293,27 @@ static int au1000_mdio_read(struct net_device *dev, int phy_addr, int reg)
mdelay(1);
if (--timedout == 0) {
netdev_err(dev, "mdio_read busy timeout!!\n");
- return -1;
+ return -ETIMEDOUT;
}
}
return readl(mii_data_reg);
}
-static void au1000_mdio_write(struct net_device *dev, int phy_addr,
- int reg, u16 value)
+static int au1000_mdio_write(struct net_device *dev, int phy_addr,
+ int reg, u16 value)
{
struct au1000_private *aup = netdev_priv(dev);
u32 *const mii_control_reg = &aup->mac->mii_control;
u32 *const mii_data_reg = &aup->mac->mii_data;
u32 timedout = 20;
u32 mii_control;
+ int ret;
while (readl(mii_control_reg) & MAC_MII_BUSY) {
mdelay(1);
if (--timedout == 0) {
netdev_err(dev, "mdio_write busy timeout!!\n");
- return;
+ return -ETIMEDOUT;
}
}
@@ -320,6 +322,13 @@ static void au1000_mdio_write(struct net_device *dev, int phy_addr,
writel(value, mii_data_reg);
writel(mii_control, mii_control_reg);
+
+ ret = readl_poll_timeout(mii_control_reg, mii_control,
+ !(mii_control & MAC_MII_BUSY), 20, 20000);
+ if (ret)
+ netdev_err(dev, "mdio_write completion timeout\n");
+
+ return ret;
}
static int au1000_mdiobus_read(struct mii_bus *bus, int phy_addr, int regnum)
@@ -344,8 +353,7 @@ static int au1000_mdiobus_write(struct mii_bus *bus, int phy_addr, int regnum,
*/
au1000_enable_mac(dev, 0);
- au1000_mdio_write(dev, phy_addr, regnum, value);
- return 0;
+ return au1000_mdio_write(dev, phy_addr, regnum, value);
}
static int au1000_mdiobus_reset(struct mii_bus *bus)
--
2.53.0
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH net v3 05/10] net: au1000: serialize TX completion with packet submission
2026-11-17 19:32 [PATCH net v3 00/10] net: au1000: Bug fixes Florian Fainelli
` (3 preceding siblings ...)
2026-11-17 19:32 ` [PATCH net v3 04/10] net: au1000: report MDIO transaction timeouts Florian Fainelli
@ 2026-11-17 19:32 ` Florian Fainelli
2026-11-17 19:32 ` [PATCH net v3 06/10] net: au1000: restore receive filtering before enabling RX Florian Fainelli
` (5 subsequent siblings)
10 siblings, 0 replies; 12+ messages in thread
From: Florian Fainelli @ 2026-11-17 19:32 UTC (permalink / raw)
To: netdev
Cc: Florian Fainelli, Andrew Lunn, David S. Miller, Eric Dumazet,
Jakub Kicinski, Paolo Abeni, Heiner Kallweit, Russell King,
Jijie Shao, Simon Horman, Runyu Xiao, David Yang,
Herbert Valerio Riedel, Danny Kukawka, Mugunthan V N,
Sebastian Hesselbarth, open list, Manuel Lauss
TX completion runs in hard IRQ context while ndo_start_xmit updates the
same descriptors and ring state without locking. An interrupt between
netif_stop_queue() and setting tx_full can miss the wakeup and leave the
queue stopped until the watchdog runs. Use the existing IRQ-safe device
lock in both paths to serialize reclamation and queue state changes.
When submission reclaims a completed descriptor at tx_head, advance
tx_tail before reusing it so the interrupt handler does not wait on the
new packet while older completions remain pending. Consume the copied
skb after releasing the lock with dev_consume_skb_any(), which also
handles netpoll entry with hardware interrupts disabled.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
---
drivers/net/ethernet/amd/au1000_eth.c | 11 ++++++++++-
1 file changed, 10 insertions(+), 1 deletion(-)
diff --git a/drivers/net/ethernet/amd/au1000_eth.c b/drivers/net/ethernet/amd/au1000_eth.c
index 1935b1d4b173..805aabc6721b 100644
--- a/drivers/net/ethernet/amd/au1000_eth.c
+++ b/drivers/net/ethernet/amd/au1000_eth.c
@@ -872,7 +872,9 @@ static void au1000_tx_ack(struct net_device *dev)
{
struct au1000_private *aup = netdev_priv(dev);
struct tx_dma *ptxd;
+ unsigned long flags;
+ spin_lock_irqsave(&aup->lock, flags);
ptxd = aup->tx_dma_ring[aup->tx_tail];
while (ptxd->buff_stat & TX_T_DONE) {
@@ -889,6 +891,8 @@ static void au1000_tx_ack(struct net_device *dev)
netif_wake_queue(dev);
}
}
+
+ spin_unlock_irqrestore(&aup->lock, flags);
}
/*
@@ -972,21 +976,25 @@ static netdev_tx_t au1000_tx(struct sk_buff *skb, struct net_device *dev)
u32 buff_stat;
struct db_dest *pDB;
int i;
+ unsigned long flags;
netif_dbg(aup, tx_queued, dev, "tx: aup %x len=%d, data=%p, head %d\n",
(unsigned)aup, skb->len,
skb->data, aup->tx_head);
+ spin_lock_irqsave(&aup->lock, flags);
ptxd = aup->tx_dma_ring[aup->tx_head];
buff_stat = ptxd->buff_stat;
if (buff_stat & TX_DMA_ENABLE) {
/* We've wrapped around and the transmitter is still busy */
netif_stop_queue(dev);
aup->tx_full = 1;
+ spin_unlock_irqrestore(&aup->lock, flags);
return NETDEV_TX_BUSY;
} else if (buff_stat & TX_T_DONE) {
au1000_update_tx_stats(dev, ptxd->status);
ptxd->len = 0;
+ aup->tx_tail = (aup->tx_tail + 1) & (NUM_TX_DMA - 1);
}
if (aup->tx_full) {
@@ -1009,8 +1017,9 @@ static netdev_tx_t au1000_tx(struct sk_buff *skb, struct net_device *dev)
ptxd->buff_stat = lower_32_bits(pDB->dma_addr) | TX_DMA_ENABLE;
wmb(); /* drain writebuffer */
- dev_kfree_skb(skb);
aup->tx_head = (aup->tx_head + 1) & (NUM_TX_DMA - 1);
+ spin_unlock_irqrestore(&aup->lock, flags);
+ dev_consume_skb_any(skb);
return NETDEV_TX_OK;
}
--
2.53.0
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH net v3 06/10] net: au1000: restore receive filtering before enabling RX
2026-11-17 19:32 [PATCH net v3 00/10] net: au1000: Bug fixes Florian Fainelli
` (4 preceding siblings ...)
2026-11-17 19:32 ` [PATCH net v3 05/10] net: au1000: serialize TX completion with packet submission Florian Fainelli
@ 2026-11-17 19:32 ` Florian Fainelli
2026-11-17 19:32 ` [PATCH net v3 07/10] net: au1000: restore RX buffer addresses when restarting the MAC Florian Fainelli
` (4 subsequent siblings)
10 siblings, 0 replies; 12+ messages in thread
From: Florian Fainelli @ 2026-11-17 19:32 UTC (permalink / raw)
To: netdev
Cc: Florian Fainelli, Andrew Lunn, David S. Miller, Eric Dumazet,
Jakub Kicinski, Paolo Abeni, Heiner Kallweit, Russell King,
Jijie Shao, Simon Horman, Runyu Xiao, David Yang,
Herbert Valerio Riedel, Danny Kukawka, Mugunthan V N,
Sebastian Hesselbarth, open list, Manuel Lauss
MAC initialization overwrites the receive mode, dropping promiscuous and
multicast settings after a watchdog reset without notifying the network
stack. Restore the requested filtering before the control write that
enables RX, avoiding a window with the wrong filter.
Factor receive-mode programming into a helper shared by initialization
and the receive-mode callback. Hold the address-list lock before the
device lock through initialization so the filter snapshot stays current.
Protect callback control-register updates with the device lock as well.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
---
drivers/net/ethernet/amd/au1000_eth.c | 23 ++++++++++++++++++++---
1 file changed, 20 insertions(+), 3 deletions(-)
diff --git a/drivers/net/ethernet/amd/au1000_eth.c b/drivers/net/ethernet/amd/au1000_eth.c
index 805aabc6721b..0e9226ea05e1 100644
--- a/drivers/net/ethernet/amd/au1000_eth.c
+++ b/drivers/net/ethernet/amd/au1000_eth.c
@@ -685,6 +685,8 @@ static const struct ethtool_ops au1000_ethtool_ops = {
.set_link_ksettings = phy_ethtool_set_link_ksettings,
};
+static u32 au1000_rx_mode(struct net_device *dev, u32 reg);
+
/*
* Initialize the interface.
*
@@ -706,6 +708,7 @@ static int au1000_init(struct net_device *dev)
/* bring the device out of reset */
au1000_enable_mac(dev, 1);
+ netif_addr_lock_bh(dev);
spin_lock_irqsave(&aup->lock, flags);
writel(0, &aup->mac->control);
@@ -738,11 +741,14 @@ static int au1000_init(struct net_device *dev)
control |= MAC_FULL_DUPLEX;
}
+ control = au1000_rx_mode(dev, control);
+
writel(control, &aup->mac->control);
writel(0x8100, &aup->mac->vlan1_tag); /* activate vlan support */
wmb(); /* drain writebuffer */
spin_unlock_irqrestore(&aup->lock, flags);
+ netif_addr_unlock_bh(dev);
return 0;
}
@@ -1036,13 +1042,12 @@ static void au1000_tx_timeout(struct net_device *dev, unsigned int txqueue)
netif_wake_queue(dev);
}
-static void au1000_multicast_list(struct net_device *dev)
+/* Caller holds the address-list lock and aup->lock. */
+static u32 au1000_rx_mode(struct net_device *dev, u32 reg)
{
struct au1000_private *aup = netdev_priv(dev);
- u32 reg;
netif_dbg(aup, drv, dev, "%s: flags=%x\n", __func__, dev->flags);
- reg = readl(&aup->mac->control);
if (dev->flags & IFF_PROMISC) { /* Set promiscuous. */
reg |= MAC_PROMISCUOUS;
} else if ((dev->flags & IFF_ALLMULTI) ||
@@ -1063,7 +1068,19 @@ static void au1000_multicast_list(struct net_device *dev)
reg &= ~(MAC_PROMISCUOUS | MAC_PASS_ALL_MULTI);
reg |= MAC_HASH_MODE;
}
+ return reg;
+}
+
+static void au1000_multicast_list(struct net_device *dev)
+{
+ struct au1000_private *aup = netdev_priv(dev);
+ unsigned long flags;
+ u32 reg;
+
+ spin_lock_irqsave(&aup->lock, flags);
+ reg = au1000_rx_mode(dev, readl(&aup->mac->control));
writel(reg, &aup->mac->control);
+ spin_unlock_irqrestore(&aup->lock, flags);
}
static const struct net_device_ops au1000_netdev_ops = {
--
2.53.0
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH net v3 07/10] net: au1000: restore RX buffer addresses when restarting the MAC
2026-11-17 19:32 [PATCH net v3 00/10] net: au1000: Bug fixes Florian Fainelli
` (5 preceding siblings ...)
2026-11-17 19:32 ` [PATCH net v3 06/10] net: au1000: restore receive filtering before enabling RX Florian Fainelli
@ 2026-11-17 19:32 ` Florian Fainelli
2026-11-17 19:32 ` [PATCH net v3 08/10] net: phy: smsc: wait for LAN83C183 power-down recovery Florian Fainelli
` (3 subsequent siblings)
10 siblings, 0 replies; 12+ messages in thread
From: Florian Fainelli @ 2026-11-17 19:32 UTC (permalink / raw)
To: netdev
Cc: Florian Fainelli, Andrew Lunn, David S. Miller, Eric Dumazet,
Jakub Kicinski, Paolo Abeni, Heiner Kallweit, Russell King,
Jijie Shao, Simon Horman, Runyu Xiao, David Yang,
Herbert Valerio Riedel, Danny Kukawka, Mugunthan V N,
Sebastian Hesselbarth, open list, Manuel Lauss
The MAC DMA engine updates each receive descriptor's address as it
transfers data. Clearing the descriptor control bits during reset does
not restore the buffer's starting address.
au1000_init() only set RX_DMA_ENABLE on the address left in the
descriptor. After closing and reopening the interface, a receive could
therefore start partway through its buffer and overwrite memory beyond
the allocation.
Reload each RX descriptor from rx_db_inuse before enabling it, as the
receive completion path already does.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
---
drivers/net/ethernet/amd/au1000_eth.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/drivers/net/ethernet/amd/au1000_eth.c b/drivers/net/ethernet/amd/au1000_eth.c
index 0e9226ea05e1..cb2f3333ba9f 100644
--- a/drivers/net/ethernet/amd/au1000_eth.c
+++ b/drivers/net/ethernet/amd/au1000_eth.c
@@ -724,7 +724,8 @@ static int au1000_init(struct net_device *dev)
for (i = 0; i < NUM_RX_DMA; i++)
- aup->rx_dma_ring[i]->buff_stat |= RX_DMA_ENABLE;
+ writel(lower_32_bits(aup->rx_db_inuse[i]->dma_addr) |
+ RX_DMA_ENABLE, &aup->rx_dma_ring[i]->buff_stat);
wmb(); /* drain writebuffer */
--
2.53.0
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH net v3 08/10] net: phy: smsc: wait for LAN83C183 power-down recovery
2026-11-17 19:32 [PATCH net v3 00/10] net: au1000: Bug fixes Florian Fainelli
` (6 preceding siblings ...)
2026-11-17 19:32 ` [PATCH net v3 07/10] net: au1000: restore RX buffer addresses when restarting the MAC Florian Fainelli
@ 2026-11-17 19:32 ` Florian Fainelli
2026-11-17 19:32 ` [PATCH net v3 09/10] net: au1000: keep the MAC stopped until the PHY link is ready Florian Fainelli
` (2 subsequent siblings)
10 siblings, 0 replies; 12+ messages in thread
From: Florian Fainelli @ 2026-11-17 19:32 UTC (permalink / raw)
To: netdev
Cc: Florian Fainelli, Andrew Lunn, David S. Miller, Eric Dumazet,
Jakub Kicinski, Paolo Abeni, Heiner Kallweit, Russell King,
Jijie Shao, Simon Horman, Runyu Xiao, David Yang,
Herbert Valerio Riedel, Danny Kukawka, Mugunthan V N,
Sebastian Hesselbarth, open list, Manuel Lauss
The LAN83C183 uses the generic PHY driver, which returns immediately
after clearing BMCR_PDOWN. Section 1.11 of the datasheet allows 500 ms
before normal operation is restored. Starting the Au1000 MAC before the
MII clocks recover can hang the MTX-1 when reopening its interface.
Add a LAN83C183 driver entry and resume callback. Wait for recovery only
when BMCR_PDOWN was actually cleared, and propagate MDIO errors without
waiting. Resuming an already awake PHY does not incur the delay.
This supplies the PHY recovery delay; it does not by itself fix the
Au1000 MAC/PHY ordering on reopen. The companion patch, "net: au1000:
keep the MAC stopped until the PHY link is ready", resumes the PHY
synchronously before MAC initialization and stops the MAC before PHY
suspend. Both changes are needed to address the MTX-1 reopen hang.
Keep this PHY change first so the recovery delay is available when the
MAC sequencing fix is applied.
Fixes: be9dad1f9f26 ("net: phy: suspend phydev when going to HALTED")
Link: https://pdf.dzsc.com/LAN/LAN83C183.pdf#page=44
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
---
drivers/net/phy/Kconfig | 2 +-
drivers/net/phy/smsc.c | 26 ++++++++++++++++++++++++++
2 files changed, 27 insertions(+), 1 deletion(-)
diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index 30e9d22c8d1a..10466b2574eb 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -421,7 +421,7 @@ config SMSC_PHY
tristate "SMSC PHYs"
select CRC16
help
- Currently supports the LAN83C185, LAN8187 and LAN8700 PHYs
+ Currently supports the LAN83C183, LAN83C185, LAN8187 and LAN8700 PHYs
config STE10XP
tristate "STMicroelectronics STe10Xp PHYs"
diff --git a/drivers/net/phy/smsc.c b/drivers/net/phy/smsc.c
index 48487149c225..c3b51afd4b1e 100644
--- a/drivers/net/phy/smsc.c
+++ b/drivers/net/phy/smsc.c
@@ -13,6 +13,7 @@
*/
#include <linux/clk.h>
+#include <linux/delay.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/mii.h>
@@ -684,8 +685,32 @@ int smsc_phy_probe(struct phy_device *phydev)
}
EXPORT_SYMBOL_GPL(smsc_phy_probe);
+static int lan83c183_resume(struct phy_device *phydev)
+{
+ int ret;
+
+ ret = phy_modify_changed(phydev, MII_BMCR, BMCR_PDOWN, 0);
+ if (ret < 0)
+ return ret;
+
+ /* The PHY needs up to 500 ms to restore operation after power-down. */
+ if (ret)
+ msleep(500);
+
+ return 0;
+}
+
static struct phy_driver smsc_phy_driver[] = {
{
+ .phy_id = 0x0016f840,
+ .phy_id_mask = 0xfffffff0,
+ .name = "SMSC LAN83C183",
+
+ .get_features = genphy_read_abilities,
+ .suspend = genphy_suspend,
+ .resume = lan83c183_resume,
+ .set_loopback = genphy_loopback,
+}, {
.phy_id = 0x0007c0a0, /* OUI=0x00800f, Model#=0x0a */
.phy_id_mask = 0xfffffff0,
.name = "SMSC LAN83C185",
@@ -887,6 +912,7 @@ MODULE_AUTHOR("Herbert Valerio Riedel");
MODULE_LICENSE("GPL");
static const struct mdio_device_id __maybe_unused smsc_tbl[] = {
+ { 0x0016f840, 0xfffffff0 },
{ 0x0007c0a0, 0xfffffff0 },
{ 0x0007c0b0, 0xfffffff0 },
{ 0x0007c0c0, 0xfffffff0 },
--
2.53.0
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH net v3 09/10] net: au1000: keep the MAC stopped until the PHY link is ready
2026-11-17 19:32 [PATCH net v3 00/10] net: au1000: Bug fixes Florian Fainelli
` (7 preceding siblings ...)
2026-11-17 19:32 ` [PATCH net v3 08/10] net: phy: smsc: wait for LAN83C183 power-down recovery Florian Fainelli
@ 2026-11-17 19:32 ` Florian Fainelli
2026-11-17 19:32 ` [PATCH net v3 10/10] net: au1000: reject frames larger than the TX bounce buffer Florian Fainelli
2026-11-17 19:38 ` [PATCH net v3 00/10] net: au1000: Bug fixes netdev-bot+sinfo
10 siblings, 0 replies; 12+ messages in thread
From: Florian Fainelli @ 2026-11-17 19:32 UTC (permalink / raw)
To: netdev
Cc: Florian Fainelli, Andrew Lunn, David S. Miller, Eric Dumazet,
Jakub Kicinski, Paolo Abeni, Heiner Kallweit, Russell King,
Jijie Shao, Simon Horman, Runyu Xiao, David Yang,
Herbert Valerio Riedel, Danny Kukawka, Mugunthan V N,
Sebastian Hesselbarth, open list, Manuel Lauss
phy_stop() powers down the PHY when the interface is closed. The driver
leaves MAC receive/transmit enabled on link-down and enables them during
initialization before the PHY resumes. MTX-1 can hang when the MAC runs
while its MII clocks are absent or still recovering.
Stop the MAC on link-down before phylib suspends the PHY. On open, clear
the driver's acknowledged link cache and synchronously resume the PHY
to restore its MII clocks and honor its recovery delay before MAC
initialization. Preserve the existing au1000_init() before phy_start()
ordering so the PHY worker cannot access MDIO or enable traffic during
setup. Leave RX/TX stopped until a link-up callback configures duplex
and enables traffic.
Use the acknowledged link and duplex cache under the device lock during
initialization, retaining it for watchdog recovery. Keep the reset-time
hard stop for paths without a preceding link-down callback. On resume
failure reset the MAC and release the IRQ. Remove the unreachable
initialization-error branch, since au1000_init() always returns zero.
Reconcile the initialization and probe comments: initialization forces
a reset itself, and PHY resume may already have enabled the MAC for
MDIO accesses.
Fixes: be9dad1f9f26 ("net: phy: suspend phydev when going to HALTED")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
---
drivers/net/ethernet/amd/au1000_eth.c | 49 ++++++++++++++++++---------
1 file changed, 33 insertions(+), 16 deletions(-)
diff --git a/drivers/net/ethernet/amd/au1000_eth.c b/drivers/net/ethernet/amd/au1000_eth.c
index cb2f3333ba9f..98a75aba92e1 100644
--- a/drivers/net/ethernet/amd/au1000_eth.c
+++ b/drivers/net/ethernet/amd/au1000_eth.c
@@ -456,7 +456,8 @@ au1000_adjust_link(struct net_device *dev)
/* link state changed */
if (!phydev->link) {
- /* link went down */
+ /* Stop the MAC before the PHY can remove its clocks. */
+ au1000_hard_stop(dev);
aup->old_speed = 0;
aup->old_duplex = -1;
}
@@ -688,13 +689,11 @@ static const struct ethtool_ops au1000_ethtool_ops = {
static u32 au1000_rx_mode(struct net_device *dev, u32 reg);
/*
- * Initialize the interface.
+ * Reset and initialize the interface.
*
- * When the device powers up, the clocks are disabled and the
- * mac is in reset state. When the interface is closed, we
- * do the same -- reset the device and disable the clocks to
- * conserve power. Thus, whenever au1000_init() is called,
- * the device should already be in reset state.
+ * The PHY must be resumed before initializing the MAC. MDIO accesses
+ * during PHY resume may have already enabled the MAC clocks and released
+ * reset; au1000_enable_mac(dev, 1) forces a reset regardless of that state.
*/
static int au1000_init(struct net_device *dev)
{
@@ -729,12 +728,12 @@ static int au1000_init(struct net_device *dev)
wmb(); /* drain writebuffer */
- control = MAC_RX_ENABLE | MAC_TX_ENABLE;
+ control = 0;
#ifndef CONFIG_CPU_LITTLE_ENDIAN
control |= MAC_BIG_ENDIAN;
#endif
if (dev->phydev) {
- if (dev->phydev->link && (DUPLEX_FULL == dev->phydev->duplex))
+ if (aup->old_link && aup->old_duplex == DUPLEX_FULL)
control |= MAC_FULL_DUPLEX;
else
control |= MAC_DISABLE_RX_OWN;
@@ -744,6 +743,10 @@ static int au1000_init(struct net_device *dev)
control = au1000_rx_mode(dev, control);
+ /* Only use link state acknowledged by au1000_adjust_link(). */
+ if (!dev->phydev || aup->old_link)
+ control |= MAC_RX_ENABLE | MAC_TX_ENABLE;
+
writel(control, &aup->mac->control);
writel(0x8100, &aup->mac->vlan1_tag); /* activate vlan support */
wmb(); /* drain writebuffer */
@@ -918,6 +921,7 @@ static irqreturn_t au1000_interrupt(int irq, void *dev_id)
static int au1000_open(struct net_device *dev)
{
+ unsigned long flags;
int retval;
struct au1000_private *aup = netdev_priv(dev);
@@ -930,13 +934,21 @@ static int au1000_open(struct net_device *dev)
return retval;
}
- retval = au1000_init(dev);
- if (retval) {
- netdev_err(dev, "error in au1000_init\n");
- free_irq(dev->irq, dev);
- return retval;
+ spin_lock_irqsave(&aup->lock, flags);
+ aup->old_link = 0;
+ aup->old_speed = 0;
+ aup->old_duplex = -1;
+ spin_unlock_irqrestore(&aup->lock, flags);
+
+ /* Restore the MII clocks without starting the PHY state machine. */
+ if (dev->phydev) {
+ retval = phy_resume(dev->phydev);
+ if (retval)
+ goto err_reset;
}
+ au1000_init(dev);
+
if (dev->phydev)
phy_start(dev->phydev);
@@ -945,6 +957,11 @@ static int au1000_open(struct net_device *dev)
netif_dbg(aup, drv, dev, "open: Initialization done.\n");
return 0;
+
+err_reset:
+ au1000_reset_mac(dev);
+ free_irq(dev->irq, dev);
+ return retval;
}
static int au1000_close(struct net_device *dev)
@@ -1306,8 +1323,8 @@ static int au1000_probe(struct platform_device *pdev)
dev->watchdog_timeo = ETH_TX_TIMEOUT;
/*
- * The boot code uses the ethernet controller, so reset it to start
- * fresh. au1000_init() expects that the device is in reset state.
+ * The boot code uses the ethernet controller, so stop it and gate
+ * its clock until the driver needs it.
*/
au1000_reset_mac(dev);
--
2.53.0
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH net v3 10/10] net: au1000: reject frames larger than the TX bounce buffer
2026-11-17 19:32 [PATCH net v3 00/10] net: au1000: Bug fixes Florian Fainelli
` (8 preceding siblings ...)
2026-11-17 19:32 ` [PATCH net v3 09/10] net: au1000: keep the MAC stopped until the PHY link is ready Florian Fainelli
@ 2026-11-17 19:32 ` Florian Fainelli
2026-11-17 19:38 ` [PATCH net v3 00/10] net: au1000: Bug fixes netdev-bot+sinfo
10 siblings, 0 replies; 12+ messages in thread
From: Florian Fainelli @ 2026-11-17 19:32 UTC (permalink / raw)
To: netdev
Cc: Florian Fainelli, Andrew Lunn, David S. Miller, Eric Dumazet,
Jakub Kicinski, Paolo Abeni, Heiner Kallweit, Russell King,
Jijie Shao, Simon Horman, Runyu Xiao, David Yang,
Herbert Valerio Riedel, Danny Kukawka, Mugunthan V N,
Sebastian Hesselbarth, open list, Manuel Lauss
au1000_tx() copies skb->len bytes into a MAX_BUF_SIZE coherent buffer
without checking the length. The copy can corrupt neighboring DMA
buffers or run beyond the coherent allocation.
AF_PACKET with PACKET_VNET_HDR can deliver oversized frames through
both plain sendmsg() and PACKET_TX_RING. In packet_snd(), a nonzero
virtio GSO type bypasses the MTU checks, even when the supplied gso_size
is large enough that virtio_net_hdr_to_skb() leaves the skb non-GSO.
Genuine GSO packets can also reach the driver as oversized frames:
au1000 has no TSO, and software segmentation using a user-supplied
gso_size can produce segments larger than MAX_BUF_SIZE.
Drop oversized packets before touching the ring or copying any data,
and account them in tx_dropped. Use an IRQ-safe skb free for netpoll.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
---
drivers/net/ethernet/amd/au1000_eth.c | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/drivers/net/ethernet/amd/au1000_eth.c b/drivers/net/ethernet/amd/au1000_eth.c
index 98a75aba92e1..3b40843d0499 100644
--- a/drivers/net/ethernet/amd/au1000_eth.c
+++ b/drivers/net/ethernet/amd/au1000_eth.c
@@ -1002,6 +1002,12 @@ static netdev_tx_t au1000_tx(struct sk_buff *skb, struct net_device *dev)
int i;
unsigned long flags;
+ if (unlikely(skb->len > MAX_BUF_SIZE)) {
+ dev->stats.tx_dropped++;
+ dev_kfree_skb_any(skb);
+ return NETDEV_TX_OK;
+ }
+
netif_dbg(aup, tx_queued, dev, "tx: aup %x len=%d, data=%p, head %d\n",
(unsigned)aup, skb->len,
skb->data, aup->tx_head);
--
2.53.0
^ permalink raw reply related [flat|nested] 12+ messages in thread
* Re: [PATCH net v3 00/10] net: au1000: Bug fixes
2026-11-17 19:32 [PATCH net v3 00/10] net: au1000: Bug fixes Florian Fainelli
` (9 preceding siblings ...)
2026-11-17 19:32 ` [PATCH net v3 10/10] net: au1000: reject frames larger than the TX bounce buffer Florian Fainelli
@ 2026-11-17 19:38 ` netdev-bot+sinfo
10 siblings, 0 replies; 12+ messages in thread
From: netdev-bot+sinfo @ 2026-11-17 19:38 UTC (permalink / raw)
To: Florian Fainelli
Cc: netdev, Andrew Lunn, David S. Miller, Eric Dumazet,
Jakub Kicinski, Paolo Abeni, Heiner Kallweit, Russell King,
Jijie Shao, Simon Horman, Runyu Xiao, David Yang,
Herbert Valerio Riedel, Danny Kukawka, Mugunthan V N,
Sebastian Hesselbarth, linux-kernel, Manuel Lauss
Hi!
This is an automated message. This series looks like a fix, but its
commit messages seem to be missing some information:
- Whether the issue was actually triggered, or is only theoretical
(e.g. found by LLM and not proven at runtime). If it was triggered
please include the symptoms, like the stack trace or kernel messages.
Please do not repost the series just to address the above. Instead,
reply to this email with the missing information, so that reviewers
can take it into account.
*IMPORTANT*: If you do repost (for other reasons) - please include
the relevant info in the cover letter or commit messages.
--
The evaluation is done by an LLM so it may be wrong, if you think
that is the case please reply and explain.
^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2026-11-17 19:38 UTC | newest]
Thread overview: 12+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2026-11-17 19:32 [PATCH net v3 00/10] net: au1000: Bug fixes Florian Fainelli
2026-11-17 19:32 ` [PATCH net v3 01/10] net: au1000: recycle RX descriptors on allocation failure Florian Fainelli
2026-11-17 19:32 ` [PATCH net v3 02/10] net: au1000: clear all-multicast mode when restoring hash filtering Florian Fainelli
2026-11-17 19:32 ` [PATCH net v3 03/10] net: au1000: disconnect the PHY before freeing the MDIO bus Florian Fainelli
2026-11-17 19:32 ` [PATCH net v3 04/10] net: au1000: report MDIO transaction timeouts Florian Fainelli
2026-11-17 19:32 ` [PATCH net v3 05/10] net: au1000: serialize TX completion with packet submission Florian Fainelli
2026-11-17 19:32 ` [PATCH net v3 06/10] net: au1000: restore receive filtering before enabling RX Florian Fainelli
2026-11-17 19:32 ` [PATCH net v3 07/10] net: au1000: restore RX buffer addresses when restarting the MAC Florian Fainelli
2026-11-17 19:32 ` [PATCH net v3 08/10] net: phy: smsc: wait for LAN83C183 power-down recovery Florian Fainelli
2026-11-17 19:32 ` [PATCH net v3 09/10] net: au1000: keep the MAC stopped until the PHY link is ready Florian Fainelli
2026-11-17 19:32 ` [PATCH net v3 10/10] net: au1000: reject frames larger than the TX bounce buffer Florian Fainelli
2026-11-17 19:38 ` [PATCH net v3 00/10] net: au1000: Bug fixes netdev-bot+sinfo
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).