From: Tim Harvey <tharvey@gateworks.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 10/14] imx: ventana: add support for GW5908
Date: Mon, 4 Feb 2019 13:10:56 -0800 [thread overview]
Message-ID: <20190204211100.11004-11-tharvey@gateworks.com> (raw)
In-Reply-To: <20190204211100.11004-1-tharvey@gateworks.com>
The GW5908 is a small single board computer based on the i.MX6DL SoC
with the same peripheral set as the GW530x but with 1GiB density DRAM
(64bit 512MiB).
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
---
board/gateworks/gw_ventana/common.c | 21 ++++++++++
board/gateworks/gw_ventana/eeprom.c | 2 +
board/gateworks/gw_ventana/gw_ventana_spl.c | 44 +++++++++++++++++++++
board/gateworks/gw_ventana/ventana_eeprom.h | 1 +
4 files changed, 68 insertions(+)
diff --git a/board/gateworks/gw_ventana/common.c b/board/gateworks/gw_ventana/common.c
index 2b0bf0e7cc..568dc920ae 100644
--- a/board/gateworks/gw_ventana/common.c
+++ b/board/gateworks/gw_ventana/common.c
@@ -1112,6 +1112,27 @@ struct ventana gpio_cfg[GW_UNKNOWN] = {
.wdis = IMX_GPIO_NR(7, 12),
.nand = true,
},
+
+ /* GW5908 */
+ {
+ .gpio_pads = gw53xx_gpio_pads,
+ .num_pads = ARRAY_SIZE(gw53xx_gpio_pads)/2,
+ .dio_cfg = gw53xx_dio,
+ .dio_num = ARRAY_SIZE(gw53xx_dio),
+ .leds = {
+ IMX_GPIO_NR(4, 6),
+ IMX_GPIO_NR(4, 7),
+ IMX_GPIO_NR(4, 15),
+ },
+ .pcie_rst = IMX_GPIO_NR(1, 29),
+ .mezz_pwren = IMX_GPIO_NR(2, 19),
+ .mezz_irq = IMX_GPIO_NR(2, 18),
+ .gps_shdn = IMX_GPIO_NR(1, 27),
+ .vidin_en = IMX_GPIO_NR(3, 31),
+ .wdis = IMX_GPIO_NR(7, 12),
+ .msata_en = GP_MSATA_SEL,
+ .rs232_en = GP_RS232_EN,
+ },
};
#define SETUP_GPIO_OUTPUT(gpio, name, level) \
diff --git a/board/gateworks/gw_ventana/eeprom.c b/board/gateworks/gw_ventana/eeprom.c
index 3aaf195b65..85802141dd 100644
--- a/board/gateworks/gw_ventana/eeprom.c
+++ b/board/gateworks/gw_ventana/eeprom.c
@@ -107,6 +107,8 @@ read_eeprom(int bus, struct ventana_board_info *info)
type = GW5906;
else if (info->model[4] == '0' && info->model[5] == '7')
type = GW5907;
+ else if (info->model[4] == '0' && info->model[5] == '8')
+ type = GW5908;
break;
}
return type;
diff --git a/board/gateworks/gw_ventana/gw_ventana_spl.c b/board/gateworks/gw_ventana/gw_ventana_spl.c
index 280493dd46..27f3774140 100644
--- a/board/gateworks/gw_ventana/gw_ventana_spl.c
+++ b/board/gateworks/gw_ventana/gw_ventana_spl.c
@@ -217,6 +217,46 @@ static struct mx6_mmdc_calibration mx6sdl_64x16_mmdc_calib = {
.p0_mpwrdlctl = 0x33382C31,
};
+/* TODO: update with calibrated values */
+static struct mx6_mmdc_calibration mx6dq_64x64_mmdc_calib = {
+ /* write leveling calibration determine */
+ .p0_mpwldectrl0 = 0x00190017,
+ .p0_mpwldectrl1 = 0x00140026,
+ .p1_mpwldectrl0 = 0x0021001C,
+ .p1_mpwldectrl1 = 0x0011001D,
+ /* Read DQS Gating calibration */
+ .p0_mpdgctrl0 = 0x43380347,
+ .p0_mpdgctrl1 = 0x433C034D,
+ .p1_mpdgctrl0 = 0x032C0324,
+ .p1_mpdgctrl1 = 0x03310232,
+ /* Read Calibration: DQS delay relative to DQ read access */
+ .p0_mprddlctl = 0x3C313539,
+ .p1_mprddlctl = 0x37343141,
+ /* Write Calibration: DQ/DM delay relative to DQS write access */
+ .p0_mpwrdlctl = 0x36393C39,
+ .p1_mpwrdlctl = 0x42344438,
+};
+
+/* TODO: update with calibrated values */
+static struct mx6_mmdc_calibration mx6sdl_64x64_mmdc_calib = {
+ /* write leveling calibration determine */
+ .p0_mpwldectrl0 = 0x003C003C,
+ .p0_mpwldectrl1 = 0x001F002A,
+ .p1_mpwldectrl0 = 0x00330038,
+ .p1_mpwldectrl1 = 0x0022003F,
+ /* Read DQS Gating calibration */
+ .p0_mpdgctrl0 = 0x42410244,
+ .p0_mpdgctrl1 = 0x4234023A,
+ .p1_mpdgctrl0 = 0x022D022D,
+ .p1_mpdgctrl1 = 0x021C0228,
+ /* Read Calibration: DQS delay relative to DQ read access */
+ .p0_mprddlctl = 0x484A4C4B,
+ .p1_mprddlctl = 0x4B4D4E4B,
+ /* Write Calibration: DQ/DM delay relative to DQS write access */
+ .p0_mpwrdlctl = 0x33342B32,
+ .p1_mpwrdlctl = 0x3933332B,
+};
+
static struct mx6_mmdc_calibration mx6dq_256x16_mmdc_calib = {
/* write leveling calibration determine */
.p0_mpwldectrl0 = 0x001B0016,
@@ -530,6 +570,10 @@ static void spl_dram_init(int width, int size_mb, int board_model)
} else if (width == 64 && size_mb == 512) {
mem = &mt41k64m16jt_125;
debug("1gB density\n");
+ if (is_cpu_type(MXC_CPU_MX6Q))
+ calib = &mx6dq_64x64_mmdc_calib;
+ else
+ calib = &mx6sdl_64x64_mmdc_calib;
} else if (width == 64 && size_mb == 1024) {
mem = &mt41k128m16jt_125;
if (is_cpu_type(MXC_CPU_MX6Q))
diff --git a/board/gateworks/gw_ventana/ventana_eeprom.h b/board/gateworks/gw_ventana/ventana_eeprom.h
index c6a38f1218..c80dfa1f7a 100644
--- a/board/gateworks/gw_ventana/ventana_eeprom.h
+++ b/board/gateworks/gw_ventana/ventana_eeprom.h
@@ -117,6 +117,7 @@ enum {
GW5905,
GW5906,
GW5907,
+ GW5908,
GW_UNKNOWN,
GW_BADCRC,
};
--
2.17.1
next prev parent reply other threads:[~2019-02-04 21:10 UTC|newest]
Thread overview: 29+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-02-04 21:10 [U-Boot] [PATCH 00/14] Gateworks Ventana updates Tim Harvey
2019-02-04 21:10 ` [U-Boot] [PATCH 01/14] imx: ventana: mv88e61xx change LED configuration Tim Harvey
2019-02-16 10:26 ` [U-Boot] [U-Boot, " sbabic at denx.de
2019-02-04 21:10 ` [U-Boot] [PATCH 02/14] imx: ventana: do not iomux UART1 Tim Harvey
2019-02-16 10:35 ` [U-Boot] [U-Boot,02/14] " sbabic at denx.de
2019-02-04 21:10 ` [U-Boot] [PATCH 03/14] imx: ventana: remove setup of I2C3 from SPL Tim Harvey
2019-02-16 10:35 ` [U-Boot] [U-Boot, " sbabic at denx.de
2019-02-04 21:10 ` [U-Boot] [PATCH 04/14] imx: ventana: add support for GW5905 Tim Harvey
2019-02-16 10:35 ` [U-Boot] [U-Boot,04/14] " sbabic at denx.de
2019-02-04 21:10 ` [U-Boot] [PATCH 05/14] imx: ventana: add support for Z101WX01 LVDS display Tim Harvey
2019-02-16 10:26 ` [U-Boot] [U-Boot, " sbabic at denx.de
2019-02-04 21:10 ` [U-Boot] [PATCH 06/14] imx: ventana: skip nand init for nandless boards Tim Harvey
2019-02-16 10:26 ` [U-Boot] [U-Boot, " sbabic at denx.de
2019-02-04 21:10 ` [U-Boot] [PATCH 07/14] imx: ventana: add i2c detect for all LVDS displays Tim Harvey
2019-02-16 10:26 ` [U-Boot] [U-Boot, " sbabic at denx.de
2019-02-04 21:10 ` [U-Boot] [PATCH 08/14] imx: ventana: add support for GW5906 Tim Harvey
2019-02-16 10:26 ` [U-Boot] [U-Boot,08/14] " sbabic at denx.de
2019-02-04 21:10 ` [U-Boot] [PATCH 09/14] imx: ventana: add support for GW5907 Tim Harvey
2019-02-16 10:45 ` [U-Boot] [U-Boot,09/14] " sbabic at denx.de
2019-02-04 21:10 ` Tim Harvey [this message]
2019-02-16 10:26 ` [U-Boot] [U-Boot,10/14] imx: ventana: add support for GW5908 sbabic at denx.de
2019-02-04 21:10 ` [U-Boot] [PATCH 11/14] imx: ventana: add support for GW5909 Tim Harvey
2019-02-16 10:35 ` [U-Boot] [U-Boot,11/14] " sbabic at denx.de
2019-02-04 21:10 ` [U-Boot] [PATCH 12/14] imx: ventana: add support for GW5901/GW5902 Tim Harvey
2019-02-16 10:35 ` [U-Boot] [U-Boot, " sbabic at denx.de
2019-02-04 21:10 ` [U-Boot] [PATCH 13/14] imx: ventana: gw5904/gw5909: disable RS485 Tim Harvey
2019-02-16 10:35 ` [U-Boot] [U-Boot, " sbabic at denx.de
2019-02-04 21:11 ` [U-Boot] [PATCH 14/14] imx: ventana: fix usage of dt paths with leading 0s (Linux 4.15+) Tim Harvey
2019-02-16 10:26 ` [U-Boot] [U-Boot, " sbabic at denx.de
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190204211100.11004-11-tharvey@gateworks.com \
--to=tharvey@gateworks.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox