From: Tim Harvey <tharvey@gateworks.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 08/14] imx: ventana: add support for GW5906
Date: Mon, 4 Feb 2019 13:10:54 -0800 [thread overview]
Message-ID: <20190204211100.11004-9-tharvey@gateworks.com> (raw)
In-Reply-To: <20190204211100.11004-1-tharvey@gateworks.com>
The GW5906 is a GW552x with mechanical and power supply connector
differences.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
---
board/gateworks/gw_ventana/common.c | 45 +++++++++++++++++++++
board/gateworks/gw_ventana/eeprom.c | 2 +
board/gateworks/gw_ventana/gw_ventana.c | 1 +
board/gateworks/gw_ventana/ventana_eeprom.h | 1 +
4 files changed, 49 insertions(+)
diff --git a/board/gateworks/gw_ventana/common.c b/board/gateworks/gw_ventana/common.c
index f54eab576c..3a187eaf8d 100644
--- a/board/gateworks/gw_ventana/common.c
+++ b/board/gateworks/gw_ventana/common.c
@@ -817,6 +817,33 @@ struct dio_cfg gw5904_dio[] = {
},
};
+struct dio_cfg gw5906_dio[] = {
+ {
+ { IOMUX_PADS(PAD_SD1_DAT0__GPIO1_IO16) },
+ IMX_GPIO_NR(1, 16),
+ { 0, 0 },
+ 0
+ },
+ {
+ { IOMUX_PADS(PAD_SD1_DAT2__GPIO1_IO19) },
+ IMX_GPIO_NR(1, 19),
+ { IOMUX_PADS(PAD_SD1_DAT2__PWM2_OUT) },
+ 2
+ },
+ {
+ { IOMUX_PADS(PAD_SD1_DAT1__GPIO1_IO17) },
+ IMX_GPIO_NR(1, 17),
+ { IOMUX_PADS(PAD_SD1_DAT1__PWM3_OUT) },
+ 3
+ },
+ {
+ {IOMUX_PADS(PAD_SD1_CLK__GPIO1_IO20) },
+ IMX_GPIO_NR(1, 20),
+ { 0, 0 },
+ 0
+ },
+};
+
/*
* Board Specific GPIO
*/
@@ -1052,6 +1079,24 @@ struct ventana gpio_cfg[GW_UNKNOWN] = {
.pcie_rst = IMX_GPIO_NR(7, 11),
.wdis = IMX_GPIO_NR(7, 13),
},
+
+ /* GW5906 */
+ {
+ .gpio_pads = gw552x_gpio_pads,
+ .num_pads = ARRAY_SIZE(gw552x_gpio_pads)/2,
+ .dio_cfg = gw5906_dio,
+ .dio_num = ARRAY_SIZE(gw5906_dio),
+ .leds = {
+ IMX_GPIO_NR(4, 6),
+ IMX_GPIO_NR(4, 7),
+ IMX_GPIO_NR(4, 15),
+ },
+ .pcie_rst = IMX_GPIO_NR(1, 29),
+ .usb_sel = IMX_GPIO_NR(1, 7),
+ .wdis = IMX_GPIO_NR(7, 12),
+ .msata_en = GP_MSATA_SEL,
+ .nand = true,
+ },
};
#define SETUP_GPIO_OUTPUT(gpio, name, level) \
diff --git a/board/gateworks/gw_ventana/eeprom.c b/board/gateworks/gw_ventana/eeprom.c
index 13ccf2b059..e697b8ca09 100644
--- a/board/gateworks/gw_ventana/eeprom.c
+++ b/board/gateworks/gw_ventana/eeprom.c
@@ -103,6 +103,8 @@ read_eeprom(int bus, struct ventana_board_info *info)
type = GW5904;
else if (info->model[4] == '0' && info->model[5] == '5')
type = GW5905;
+ else if (info->model[4] == '0' && info->model[5] == '6')
+ type = GW5906;
break;
}
return type;
diff --git a/board/gateworks/gw_ventana/gw_ventana.c b/board/gateworks/gw_ventana/gw_ventana.c
index fb81a96e77..da9f5d89be 100644
--- a/board/gateworks/gw_ventana/gw_ventana.c
+++ b/board/gateworks/gw_ventana/gw_ventana.c
@@ -155,6 +155,7 @@ int board_ehci_hcd_init(int port)
switch (board_type) {
case GW53xx:
case GW552x:
+ case GW5906:
gpio = (IMX_GPIO_NR(1, 9));
break;
case GW54proto:
diff --git a/board/gateworks/gw_ventana/ventana_eeprom.h b/board/gateworks/gw_ventana/ventana_eeprom.h
index f2d87373ec..80a702389c 100644
--- a/board/gateworks/gw_ventana/ventana_eeprom.h
+++ b/board/gateworks/gw_ventana/ventana_eeprom.h
@@ -115,6 +115,7 @@ enum {
GW5903,
GW5904,
GW5905,
+ GW5906,
GW_UNKNOWN,
GW_BADCRC,
};
--
2.17.1
next prev parent reply other threads:[~2019-02-04 21:10 UTC|newest]
Thread overview: 29+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-02-04 21:10 [U-Boot] [PATCH 00/14] Gateworks Ventana updates Tim Harvey
2019-02-04 21:10 ` [U-Boot] [PATCH 01/14] imx: ventana: mv88e61xx change LED configuration Tim Harvey
2019-02-16 10:26 ` [U-Boot] [U-Boot, " sbabic at denx.de
2019-02-04 21:10 ` [U-Boot] [PATCH 02/14] imx: ventana: do not iomux UART1 Tim Harvey
2019-02-16 10:35 ` [U-Boot] [U-Boot,02/14] " sbabic at denx.de
2019-02-04 21:10 ` [U-Boot] [PATCH 03/14] imx: ventana: remove setup of I2C3 from SPL Tim Harvey
2019-02-16 10:35 ` [U-Boot] [U-Boot, " sbabic at denx.de
2019-02-04 21:10 ` [U-Boot] [PATCH 04/14] imx: ventana: add support for GW5905 Tim Harvey
2019-02-16 10:35 ` [U-Boot] [U-Boot,04/14] " sbabic at denx.de
2019-02-04 21:10 ` [U-Boot] [PATCH 05/14] imx: ventana: add support for Z101WX01 LVDS display Tim Harvey
2019-02-16 10:26 ` [U-Boot] [U-Boot, " sbabic at denx.de
2019-02-04 21:10 ` [U-Boot] [PATCH 06/14] imx: ventana: skip nand init for nandless boards Tim Harvey
2019-02-16 10:26 ` [U-Boot] [U-Boot, " sbabic at denx.de
2019-02-04 21:10 ` [U-Boot] [PATCH 07/14] imx: ventana: add i2c detect for all LVDS displays Tim Harvey
2019-02-16 10:26 ` [U-Boot] [U-Boot, " sbabic at denx.de
2019-02-04 21:10 ` Tim Harvey [this message]
2019-02-16 10:26 ` [U-Boot] [U-Boot,08/14] imx: ventana: add support for GW5906 sbabic at denx.de
2019-02-04 21:10 ` [U-Boot] [PATCH 09/14] imx: ventana: add support for GW5907 Tim Harvey
2019-02-16 10:45 ` [U-Boot] [U-Boot,09/14] " sbabic at denx.de
2019-02-04 21:10 ` [U-Boot] [PATCH 10/14] imx: ventana: add support for GW5908 Tim Harvey
2019-02-16 10:26 ` [U-Boot] [U-Boot,10/14] " sbabic at denx.de
2019-02-04 21:10 ` [U-Boot] [PATCH 11/14] imx: ventana: add support for GW5909 Tim Harvey
2019-02-16 10:35 ` [U-Boot] [U-Boot,11/14] " sbabic at denx.de
2019-02-04 21:10 ` [U-Boot] [PATCH 12/14] imx: ventana: add support for GW5901/GW5902 Tim Harvey
2019-02-16 10:35 ` [U-Boot] [U-Boot, " sbabic at denx.de
2019-02-04 21:10 ` [U-Boot] [PATCH 13/14] imx: ventana: gw5904/gw5909: disable RS485 Tim Harvey
2019-02-16 10:35 ` [U-Boot] [U-Boot, " sbabic at denx.de
2019-02-04 21:11 ` [U-Boot] [PATCH 14/14] imx: ventana: fix usage of dt paths with leading 0s (Linux 4.15+) Tim Harvey
2019-02-16 10:26 ` [U-Boot] [U-Boot, " sbabic at denx.de
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190204211100.11004-9-tharvey@gateworks.com \
--to=tharvey@gateworks.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox