[PATCH V3 14/14] ARM: dts: stm32: Split AV96 into DHCOR SoM and AV96 board

[Marek Vasut <marex@denx.de>]

The AV96 is in fact an assembly of DH Electronics DHCOR SoM on top
of an AV96 reference board. Split the DTs to reflect that and make
sure to DHCOR SoM can be reused on other boards easily.

It is also highly recommended to configure the board for the DHCOM
make stm32mp15_dhcom_basic_defconfig
make DEVICE_TREE=stm32mp15xx-dhcor-avenger96
as that permits reusing the board code for the DH components, like
accessing and reading out the ethernet MAC from EEPROM.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
---
V2: No change
V3: No change
---
 arch/arm/dts/Makefile                         |   3 +-
 arch/arm/dts/stm32mp157a-avenger96.dts        | 421 +-----------------
 .../stm32mp15xx-dhcor-avenger96-u-boot.dtsi   |  80 ++++
 arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts  | 211 +++++++++
 ...oot.dtsi => stm32mp15xx-dhcor-u-boot.dtsi} |  79 +---
 arch/arm/dts/stm32mp15xx-dhcor.dtsi           | 231 ++++++++++
 doc/board/st/stm32mp1.rst                     |   8 +-
 7 files changed, 535 insertions(+), 498 deletions(-)
 create mode 100644 arch/arm/dts/stm32mp15xx-dhcor-avenger96-u-boot.dtsi
 create mode 100644 arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts
 rename arch/arm/dts/{stm32mp157a-avenger96-u-boot.dtsi => stm32mp15xx-dhcor-u-boot.dtsi} (75%)
 create mode 100644 arch/arm/dts/stm32mp15xx-dhcor.dtsi

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 9c593b2c98..2564f790de 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -884,7 +884,8 @@ dtb-$(CONFIG_STM32MP15x) += \
 	stm32mp157c-dk2.dtb \
 	stm32mp157c-ed1.dtb \
 	stm32mp157c-ev1.dtb \
-	stm32mp15xx-dhcom-pdk2.dtb
+	stm32mp15xx-dhcom-pdk2.dtb \
+	stm32mp15xx-dhcor-avenger96.dtb
 
 dtb-$(CONFIG_SOC_K3_AM6) += k3-am654-base-board.dtb k3-am654-r5-base-board.dtb
 dtb-$(CONFIG_SOC_K3_J721E) += k3-j721e-common-proc-board.dtb \
diff --git a/arch/arm/dts/stm32mp157a-avenger96.dts b/arch/arm/dts/stm32mp157a-avenger96.dts
index 97ff40144e..9c165104fb 100644
--- a/arch/arm/dts/stm32mp157a-avenger96.dts
+++ b/arch/arm/dts/stm32mp157a-avenger96.dts
@@ -4,422 +4,5 @@
  * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
  */
 
-/dts-v1/;
-
-#include "stm32mp157c.dtsi"
-#include "stm32mp157xac-pinctrl.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/mfd/st,stpmic1.h>
-
-/ {
-	model = "Arrow Electronics STM32MP157A Avenger96 board";
-	compatible = "arrow,stm32mp157a-avenger96", "st,stm32mp157";
-
-	aliases {
-		ethernet0 = &ethernet0;
-		mmc0 = &sdmmc1;
-		serial0 = &uart4;
-		serial1 = &uart7;
-		spi0 = &qspi;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	memory at c0000000 {
-		device_type = "memory";
-		reg = <0xc0000000 0x40000000>;
-	};
-
-	led {
-		compatible = "gpio-leds";
-		led1 {
-			label = "green:user1";
-			gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-			default-state = "off";
-		};
-
-		led2 {
-			label = "green:user2";
-			gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "mmc0";
-			default-state = "off";
-		};
-
-		led3 {
-			label = "green:user3";
-			gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "mmc1";
-			default-state = "off";
-		};
-
-		led4 {
-			label = "green:user3";
-			gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "none";
-			default-state = "off";
-			panic-indicator;
-		};
-
-		led5 {
-			label = "yellow:wifi";
-			gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "phy0tx";
-			default-state = "off";
-		};
-
-		led6 {
-			label = "blue:bt";
-			gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "bluetooth-power";
-			default-state = "off";
-		};
-	};
-
-	sd_switch: regulator-sd_switch {
-		compatible = "regulator-gpio";
-		regulator-name = "sd_switch";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <2900000>;
-		regulator-type = "voltage";
-		regulator-always-on;
-
-		gpios = <&gpioi 5 GPIO_ACTIVE_HIGH>;
-		gpios-states = <0>;
-		states = <1800000 0x1>,
-			 <2900000 0x0>;
-	};
-
-	/* Enpirion EP3A8LQI U2 on the DHCOR */
-	vdd_io: regulator-buck-io {
-		compatible = "regulator-fixed";
-		regulator-name = "buck-io";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		regulator-always-on;
-		regulator-boot-on;
-		vin-supply = <&vdd>;
-	};
-};
-
-&ethernet0 {
-	status = "okay";
-	pinctrl-0 = <&ethernet0_rgmii_pins_b>;
-	pinctrl-1 = <&ethernet0_rgmii_pins_sleep_b>;
-	pinctrl-names = "default", "sleep";
-	phy-mode = "rgmii";
-	max-speed = <1000>;
-	phy-handle = <&phy0>;
-	phy-reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
-
-	mdio0 {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		compatible = "snps,dwmac-mdio";
-		phy0: ethernet-phy at 7 {
-			reg = <7>;
-		};
-	};
-};
-
-&i2c1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins_b>;
-	i2c-scl-rising-time-ns = <185>;
-	i2c-scl-falling-time-ns = <20>;
-	status = "okay";
-	/delete-property/dmas;
-	/delete-property/dma-names;
-};
-
-&i2c2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c2_pins_b1 &i2c2_pins_b2>;
-	i2c-scl-rising-time-ns = <185>;
-	i2c-scl-falling-time-ns = <20>;
-	status = "okay";
-	/delete-property/dmas;
-	/delete-property/dma-names;
-};
-
-&i2c4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c4_pins_a>;
-	i2c-scl-rising-time-ns = <185>;
-	i2c-scl-falling-time-ns = <20>;
-	status = "okay";
-	/delete-property/dmas;
-	/delete-property/dma-names;
-
-	pmic: stpmic at 33 {
-		compatible = "st,stpmic1";
-		reg = <0x33>;
-		interrupts-extended = <&exti 55 IRQ_TYPE_EDGE_FALLING>;
-		interrupt-controller;
-		#interrupt-cells = <2>;
-		status = "okay";
-
-		st,main-control-register = <0x04>;
-		st,vin-control-register = <0xc0>;
-		st,usb-control-register = <0x30>;
-
-		regulators {
-			compatible = "st,stpmic1-regulators";
-
-			ldo1-supply = <&v3v3>;
-			ldo2-supply = <&v3v3>;
-			ldo3-supply = <&vdd_ddr>;
-			ldo5-supply = <&v3v3>;
-			ldo6-supply = <&v3v3>;
-			pwr_sw1-supply = <&bst_out>;
-			pwr_sw2-supply = <&bst_out>;
-
-			vddcore: buck1 {
-				regulator-name = "vddcore";
-				regulator-min-microvolt = <800000>;
-				regulator-max-microvolt = <1350000>;
-				regulator-always-on;
-				regulator-initial-mode = <0>;
-				regulator-over-current-protection;
-			};
-
-			vdd_ddr: buck2 {
-				regulator-name = "vdd_ddr";
-				regulator-min-microvolt = <1350000>;
-				regulator-max-microvolt = <1350000>;
-				regulator-always-on;
-				regulator-initial-mode = <0>;
-				regulator-over-current-protection;
-			};
-
-			vdd: buck3 {
-				regulator-name = "vdd";
-				regulator-min-microvolt = <2900000>;
-				regulator-max-microvolt = <2900000>;
-				regulator-always-on;
-				st,mask_reset;
-				regulator-initial-mode = <0>;
-				regulator-over-current-protection;
-			};
-
-			v3v3: buck4 {
-				regulator-name = "v3v3";
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-always-on;
-				regulator-over-current-protection;
-				regulator-initial-mode = <0>;
-			};
-
-			vdda: ldo1 {
-				regulator-name = "vdda";
-				regulator-min-microvolt = <2900000>;
-				regulator-max-microvolt = <2900000>;
-				interrupts = <IT_CURLIM_LDO1 0>;
-				interrupt-parent = <&pmic>;
-			};
-
-			v2v8: ldo2 {
-				regulator-name = "v2v8";
-				regulator-min-microvolt = <2800000>;
-				regulator-max-microvolt = <2800000>;
-				interrupts = <IT_CURLIM_LDO2 0>;
-				interrupt-parent = <&pmic>;
-			};
-
-			vtt_ddr: ldo3 {
-				regulator-name = "vtt_ddr";
-				regulator-min-microvolt = <500000>;
-				regulator-max-microvolt = <750000>;
-				regulator-always-on;
-				regulator-over-current-protection;
-			};
-
-			vdd_usb: ldo4 {
-				regulator-name = "vdd_usb";
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
-				interrupts = <IT_CURLIM_LDO4 0>;
-				interrupt-parent = <&pmic>;
-			};
-
-			vdd_sd: ldo5 {
-				regulator-name = "vdd_sd";
-				regulator-min-microvolt = <2900000>;
-				regulator-max-microvolt = <2900000>;
-				interrupts = <IT_CURLIM_LDO5 0>;
-				interrupt-parent = <&pmic>;
-				regulator-boot-on;
-			};
-
-			v1v8: ldo6 {
-				regulator-name = "v1v8";
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-				interrupts = <IT_CURLIM_LDO6 0>;
-				interrupt-parent = <&pmic>;
-				regulator-enable-ramp-delay = <300000>;
-			};
-
-			vref_ddr: vref_ddr {
-				regulator-name = "vref_ddr";
-				regulator-always-on;
-				regulator-over-current-protection;
-			};
-
-			bst_out: boost {
-				regulator-name = "bst_out";
-				interrupts = <IT_OCP_BOOST 0>;
-				interrupt-parent = <&pmic>;
-			};
-
-			vbus_otg: pwr_sw1 {
-				regulator-name = "vbus_otg";
-				interrupts = <IT_OCP_OTG 0>;
-				interrupt-parent = <&pmic>;
-				regulator-active-discharge = <1>;
-			};
-
-			vbus_sw: pwr_sw2 {
-				regulator-name = "vbus_sw";
-				interrupts = <IT_OCP_SWOUT 0>;
-				interrupt-parent = <&pmic>;
-				regulator-active-discharge = <1>;
-			};
-		};
-
-		onkey {
-			compatible = "st,stpmic1-onkey";
-			interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>;
-			interrupt-names = "onkey-falling", "onkey-rising";
-			status = "okay";
-		};
-
-		watchdog {
-			compatible = "st,stpmic1-wdt";
-			status = "disabled";
-		};
-	};
-
-	eeprom at 53 {
-		compatible = "atmel,24c02";
-		reg = <0x53>;
-		pagesize = <16>;
-	};
-};
-
-&iwdg2 {
-	timeout-sec = <32>;
-	status = "okay";
-};
-
-&pwr_regulators {
-	vdd-supply = <&vdd_io>;
-	vdd_3v3_usbfs-supply = <&vdd_usb>;
-};
-
-&qspi {
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>;
-	pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>;
-	reg = <0x58003000 0x1000>, <0x70000000 0x200000>;
-	#address-cells = <1>;
-	#size-cells = <0>;
-	status = "okay";
-
-	flash0: spi-flash at 0 {
-		compatible = "jedec,spi-nor";
-		reg = <0>;
-		spi-rx-bus-width = <4>;
-		spi-max-frequency = <108000000>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-	};
-};
-
-&rng1 {
-	status = "okay";
-};
-
-&rtc {
-	status = "okay";
-};
-
-&sdmmc1 {
-	pinctrl-names = "default", "opendrain", "sleep";
-	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>;
-	pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>;
-	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>;
-	cd-gpios = <&gpioi 8 GPIO_ACTIVE_LOW>;
-	disable-wp;
-	st,sig-dir;
-	st,neg-edge;
-	st,use-ckin;
-	sd-uhs-sdr104;
-	bus-width = <4>;
-	vmmc-supply = <&vdd_sd>;
-	vqmmc-supply = <&sd_switch>;
-	status = "okay";
-};
-
-&sdmmc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>;
-	non-removable;
-	no-sd;
-	no-sdio;
-	st,neg-edge;
-	bus-width = <8>;
-	vmmc-supply = <&v3v3>;
-	mmc-ddr-3_3v;
-	status = "okay";
-};
-
-&spi2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&spi2_pins_a>;
-	status = "okay";
-};
-
-&uart4 {
-	/* On Low speed expansion header */
-	label = "LS-UART1";
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart4_pins_b>;
-	status = "okay";
-};
-
-&uart7 {
-	/* On Low speed expansion header */
-	label = "LS-UART0";
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart7_pins_a>;
-	status = "okay";
-};
-
-&usbh_ehci {
-	phys = <&usbphyc_port0>;
-	phy-names = "usb";
-	status = "okay";
-};
-
-&usbotg_hs {
-	dr_mode = "peripheral";
-	phys = <&usbphyc_port1 0>;
-	phy-names = "usb2-phy";
-	status = "okay";
-};
-
-&usbphyc {
-	status = "okay";
-};
-
-&usbphyc_port0 {
-	phy-supply = <&vdd_usb>;
-};
-
-&usbphyc_port1 {
-	phy-supply = <&vdd_usb>;
-};
+/* This is kept for backward compatibility and will be removed */
+#include "stm32mp15xx-dhcor-avenger96.dts"
diff --git a/arch/arm/dts/stm32mp15xx-dhcor-avenger96-u-boot.dtsi b/arch/arm/dts/stm32mp15xx-dhcor-avenger96-u-boot.dtsi
new file mode 100644
index 0000000000..4207a96618
--- /dev/null
+++ b/arch/arm/dts/stm32mp15xx-dhcor-avenger96-u-boot.dtsi
@@ -0,0 +1,80 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2020 Marek Vasut <marex@denx.de>
+ */
+
+#include "stm32mp15xx-dhcor-u-boot.dtsi"
+
+/ {
+	aliases {
+		mmc0 = &sdmmc1;
+		mmc1 = &sdmmc2;
+		usb0 = &usbotg_hs;
+	};
+
+	config {
+		u-boot,boot-led = "led1";
+		u-boot,error-led = "led4";
+	};
+};
+
+&sdmmc1 {
+	u-boot,dm-spl;
+};
+
+&sdmmc1_b4_pins_a {
+	u-boot,dm-spl;
+	pins {
+		u-boot,dm-spl;
+	};
+};
+
+&sdmmc1_dir_pins_b {
+	u-boot,dm-spl;
+	pins1 {
+		u-boot,dm-spl;
+	};
+	pins2 {
+		u-boot,dm-spl;
+	};
+};
+
+&sdmmc2 {
+	u-boot,dm-spl;
+};
+
+&sdmmc2_b4_pins_a {
+	u-boot,dm-spl;
+	pins1 {
+		u-boot,dm-spl;
+	};
+	pins2 {
+		u-boot,dm-spl;
+	};
+};
+
+&sdmmc2_d47_pins_b {
+	u-boot,dm-spl;
+	pins {
+		u-boot,dm-spl;
+	};
+};
+
+&uart4 {
+	u-boot,dm-pre-reloc;
+};
+
+&uart4_pins_b {
+	u-boot,dm-pre-reloc;
+	pins1 {
+		u-boot,dm-pre-reloc;
+	};
+	pins2 {
+		u-boot,dm-pre-reloc;
+	};
+};
+
+&usbotg_hs {
+	u-boot,force-b-session-valid;
+	hnp-srp-disable;
+};
diff --git a/arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts b/arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts
new file mode 100644
index 0000000000..9d859e1d09
--- /dev/null
+++ b/arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts
@@ -0,0 +1,211 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
+ * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+ * Copyright (C) 2020 Marek Vasut <marex@denx.de>
+ */
+
+/dts-v1/;
+
+#include "stm32mp15xx-dhcor.dtsi"
+#include "stm32mp15xx-dhcor-avenger96-u-boot.dtsi"
+
+/ {
+	model = "Arrow Electronics STM32MP15xx Avenger96 board";
+	compatible = "arrow,stm32mp15xx-avenger96", "st,stm32mp15x";
+
+	aliases {
+		eeprom0 = &eeprom0;
+		ethernet0 = &ethernet0;
+		mmc0 = &sdmmc1;
+		serial0 = &uart4;
+		serial1 = &uart7;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	led {
+		compatible = "gpio-leds";
+		led1 {
+			label = "green:user1";
+			gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+
+		led2 {
+			label = "green:user2";
+			gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc0";
+			default-state = "off";
+		};
+
+		led3 {
+			label = "green:user3";
+			gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc1";
+			default-state = "off";
+		};
+
+		led4 {
+			label = "green:user3";
+			gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "none";
+			default-state = "off";
+			panic-indicator;
+		};
+
+		led5 {
+			label = "yellow:wifi";
+			gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "phy0tx";
+			default-state = "off";
+		};
+
+		led6 {
+			label = "blue:bt";
+			gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "bluetooth-power";
+			default-state = "off";
+		};
+	};
+
+	sd_switch: regulator-sd_switch {
+		compatible = "regulator-gpio";
+		regulator-name = "sd_switch";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2900000>;
+		regulator-type = "voltage";
+		regulator-always-on;
+
+		gpios = <&gpioi 5 GPIO_ACTIVE_HIGH>;
+		gpios-states = <0>;
+		states = <1800000 0x1>,
+			 <2900000 0x0>;
+	};
+};
+
+&ethernet0 {
+	status = "okay";
+	pinctrl-0 = <&ethernet0_rgmii_pins_b>;
+	pinctrl-1 = <&ethernet0_rgmii_pins_sleep_b>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rgmii";
+	max-speed = <1000>;
+	phy-handle = <&phy0>;
+	phy-reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy0: ethernet-phy at 7 {
+			reg = <7>;
+		};
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins_b>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins_b1 &i2c2_pins_b2>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&i2c4 {
+	eeprom0: eeprom at 53 {
+		compatible = "atmel,24c02";
+		reg = <0x53>;
+		pagesize = <16>;
+	};
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>;
+	disable-wp;
+	st,sig-dir;
+	st,neg-edge;
+	st,use-ckin;
+	bus-width = <4>;
+	vmmc-supply = <&vdd_sd>;
+	vqmmc-supply = <&sd_switch>;
+	status = "okay";
+};
+
+&sdmmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	st,neg-edge;
+	bus-width = <8>;
+	vmmc-supply = <&v3v3>;
+	mmc-ddr-3_3v;
+	status = "okay";
+};
+
+&spi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_a>;
+	status = "okay";
+};
+
+&uart4 {
+	/* On Low speed expansion header */
+	label = "LS-UART1";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins_b>;
+	status = "okay";
+};
+
+&uart7 {
+	/* On Low speed expansion header */
+	label = "LS-UART0";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart7_pins_a>;
+	status = "okay";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	phy-names = "usb";
+	status = "okay";
+};
+
+&usbotg_hs {
+	dr_mode = "peripheral";
+	phys = <&usbphyc_port1 0>;
+	phy-names = "usb2-phy";
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
diff --git a/arch/arm/dts/stm32mp157a-avenger96-u-boot.dtsi b/arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi
similarity index 75%
rename from arch/arm/dts/stm32mp157a-avenger96-u-boot.dtsi
rename to arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi
index 320132a01e..02dad81b0b 100644
--- a/arch/arm/dts/stm32mp157a-avenger96-u-boot.dtsi
+++ b/arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi
@@ -4,25 +4,13 @@
  *
  * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
  * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+ * Copyright (C) 2020 Marek Vasut <marex@denx.de>
  */
 
 #include <dt-bindings/clock/stm32mp1-clksrc.h>
 #include "stm32mp157-u-boot.dtsi"
 #include "stm32mp15-ddr3-2x4Gb-1066-binG.dtsi"
 
-/ {
-	aliases {
-		mmc0 = &sdmmc1;
-		mmc1 = &sdmmc2;
-		usb0 = &usbotg_hs;
-	};
-
-	config {
-		u-boot,boot-led = "led1";
-		u-boot,error-led = "led4";
-	};
-};
-
 &i2c4 {
 	u-boot,dm-pre-reloc;
 };
@@ -38,6 +26,10 @@
 	u-boot,dm-pre-reloc;
 };
 
+&qspi {
+	u-boot,dm-spl;
+};
+
 &rcc {
 	st,clksrc = <
 		CLK_MPU_PLL1P
@@ -139,67 +131,6 @@
 	};
 };
 
-&sdmmc1 {
-	u-boot,dm-spl;
-};
-
-&sdmmc1_b4_pins_a {
-	u-boot,dm-spl;
-	pins {
-		u-boot,dm-spl;
-	};
-};
-
-&sdmmc1_dir_pins_b {
-	u-boot,dm-spl;
-	pins1 {
-		u-boot,dm-spl;
-	};
-	pins2 {
-		u-boot,dm-spl;
-	};
-};
-
-&sdmmc2 {
-	u-boot,dm-spl;
-};
-
-&sdmmc2_b4_pins_a {
-	u-boot,dm-spl;
-	pins1 {
-		u-boot,dm-spl;
-	};
-	pins2 {
-		u-boot,dm-spl;
-	};
-};
-
-&sdmmc2_d47_pins_b {
-	u-boot,dm-spl;
-	pins {
-		u-boot,dm-spl;
-	};
-};
-
-&uart4 {
-	u-boot,dm-pre-reloc;
-};
-
-&uart4_pins_b {
-	u-boot,dm-pre-reloc;
-	pins1 {
-		u-boot,dm-pre-reloc;
-	};
-	pins2 {
-		u-boot,dm-pre-reloc;
-	};
-};
-
-&usbotg_hs {
-	u-boot,force-b-session-valid;
-	hnp-srp-disable;
-};
-
 &v3v3 {
 	regulator-always-on;
 };
diff --git a/arch/arm/dts/stm32mp15xx-dhcor.dtsi b/arch/arm/dts/stm32mp15xx-dhcor.dtsi
new file mode 100644
index 0000000000..9d4e92ebb1
--- /dev/null
+++ b/arch/arm/dts/stm32mp15xx-dhcor.dtsi
@@ -0,0 +1,231 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
+ * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+ * Copyright (C) 2020 Marek Vasut <marex@denx.de>
+ */
+/dts-v1/;
+
+#include "stm32mp157c.dtsi"
+#include "stm32mp157xac-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+	aliases {
+		spi0 = &qspi;
+	};
+
+	memory at c0000000 {
+		device_type = "memory";
+		reg = <0xc0000000 0x40000000>;
+	};
+
+	/* Enpirion EP3A8LQI U2 on the DHCOR */
+	vdd_io: regulator-buck-io {
+		compatible = "regulator-fixed";
+		regulator-name = "buck-io";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vdd>;
+	};
+};
+
+&i2c4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c4_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	pmic: stpmic at 33 {
+		compatible = "st,stpmic1";
+		reg = <0x33>;
+		interrupts-extended = <&exti 55 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		status = "okay";
+
+		st,main-control-register = <0x04>;
+		st,vin-control-register = <0xc0>;
+		st,usb-control-register = <0x30>;
+
+		regulators {
+			compatible = "st,stpmic1-regulators";
+
+			ldo1-supply = <&v3v3>;
+			ldo2-supply = <&v3v3>;
+			ldo3-supply = <&vdd_ddr>;
+			ldo5-supply = <&v3v3>;
+			ldo6-supply = <&v3v3>;
+			pwr_sw1-supply = <&bst_out>;
+			pwr_sw2-supply = <&bst_out>;
+
+			vddcore: buck1 {
+				regulator-name = "vddcore";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd_ddr: buck2 {
+				regulator-name = "vdd_ddr";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd: buck3 {
+				regulator-name = "vdd";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				regulator-always-on;
+				st,mask_reset;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			v3v3: buck4 {
+				regulator-name = "v3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+				regulator-initial-mode = <0>;
+			};
+
+			vdda: ldo1 {
+				regulator-name = "vdda";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO1 0>;
+				interrupt-parent = <&pmic>;
+			};
+
+			v2v8: ldo2 {
+				regulator-name = "v2v8";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				interrupts = <IT_CURLIM_LDO2 0>;
+				interrupt-parent = <&pmic>;
+			};
+
+			vtt_ddr: ldo3 {
+				regulator-name = "vtt_ddr";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <750000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			vdd_usb: ldo4 {
+				regulator-name = "vdd_usb";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				interrupts = <IT_CURLIM_LDO4 0>;
+				interrupt-parent = <&pmic>;
+			};
+
+			vdd_sd: ldo5 {
+				regulator-name = "vdd_sd";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO5 0>;
+				interrupt-parent = <&pmic>;
+				regulator-boot-on;
+			};
+
+			v1v8: ldo6 {
+				regulator-name = "v1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				interrupts = <IT_CURLIM_LDO6 0>;
+				interrupt-parent = <&pmic>;
+				regulator-enable-ramp-delay = <300000>;
+			};
+
+			vref_ddr: vref_ddr {
+				regulator-name = "vref_ddr";
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			bst_out: boost {
+				regulator-name = "bst_out";
+				interrupts = <IT_OCP_BOOST 0>;
+				interrupt-parent = <&pmic>;
+			};
+
+			vbus_otg: pwr_sw1 {
+				regulator-name = "vbus_otg";
+				interrupts = <IT_OCP_OTG 0>;
+				interrupt-parent = <&pmic>;
+				regulator-active-discharge = <1>;
+			};
+
+			vbus_sw: pwr_sw2 {
+				regulator-name = "vbus_sw";
+				interrupts = <IT_OCP_SWOUT 0>;
+				interrupt-parent = <&pmic>;
+				regulator-active-discharge = <1>;
+			};
+		};
+
+		onkey {
+			compatible = "st,stpmic1-onkey";
+			interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>;
+			interrupt-names = "onkey-falling", "onkey-rising";
+			status = "okay";
+		};
+
+		watchdog {
+			compatible = "st,stpmic1-wdt";
+			status = "disabled";
+		};
+	};
+};
+
+&iwdg2 {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&pwr_regulators {
+	vdd-supply = <&vdd_io>;
+	vdd_3v3_usbfs-supply = <&vdd_usb>;
+};
+
+&qspi {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>;
+	pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>;
+	reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	flash0: spi-flash at 0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
+&rng1 {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
diff --git a/doc/board/st/stm32mp1.rst b/doc/board/st/stm32mp1.rst
index 1640bf910e..73195134f1 100644
--- a/doc/board/st/stm32mp1.rst
+++ b/doc/board/st/stm32mp1.rst
@@ -43,11 +43,11 @@ And the necessary drivers
 
 Currently the following boards are supported:
 
- + stm32mp157a-avenger96.dts
  + stm32mp157a-dk1.dts
  + stm32mp157c-dk2.dts
  + stm32mp157c-ed1.dts
  + stm32mp157c-ev1.dts
+ + stm32mp15xx-dhcor-avenger96.dts
 
 Boot Sequences
 --------------
@@ -145,9 +145,9 @@ the supported device trees for STM32MP15x are:
 
    + stm32mp157c-dk2
 
-+ avenger96: Avenger96 board from Arrow Electronics
++ avenger96: Avenger96 board from Arrow Electronics based on DH Elec. DHCOR SoM
 
-   + stm32mp157a-avenger96
+   + stm32mp15xx-dhcor-avenger96
 
 Build Procedure
 ---------------
@@ -229,7 +229,7 @@ Build Procedure
 
      # export KBUILD_OUTPUT=stm32mp15_basic
      # make stm32mp15_basic_defconfig
-     # make DEVICE_TREE=stm32mp157a-avenger96 all
+     # make DEVICE_TREE=stm32mp15xx-dhcor-avenger96 all
 
 6. Output files
 
-- 
2.25.1