From: Michael Walle <michael@walle.cc>
To: u-boot@lists.denx.de
Subject: U-Boot atheros PHY support and cubox ethernet
Date: Wed, 17 Jun 2020 09:19:11 +0200 [thread overview]
Message-ID: <8dc08cb43e9ff3cfb3ade9d91f8d4d61@walle.cc> (raw)
In-Reply-To: <CA+h21hpBgWWYtc9LdOhd+fDGH9yuzoXKntjxY-e7BCtagC9dSw@mail.gmail.com>
Am 2020-06-16 23:57, schrieb Vladimir Oltean:
> On Wed, 17 Jun 2020 at 00:35, Tom Rini <trini@konsulko.com> wrote:
>>
>> On Tue, Jun 16, 2020 at 11:37:17PM +0300, Vladimir Oltean wrote:
>> > On Tue, 16 Jun 2020 at 23:31, Tom Rini <trini@konsulko.com> wrote:
>> > >
>> > > On Tue, Jun 16, 2020 at 11:21:08PM +0300, Vladimir Oltean wrote:
>> > > > On Tue, 16 Jun 2020 at 23:10, Tom Rini <trini@konsulko.com> wrote:
>> > > > >
>> > > > > On Tue, Jun 16, 2020 at 10:58:26PM +0300, Vladimir Oltean wrote:
>> > > > > > Hi Tom,
>> > > > > >
>> > > > > > On Tue, 16 Jun 2020 at 22:55, Tom Rini <trini@konsulko.com> wrote:
>> > > > > > >
>> > > > > > > Hey all,
>> > > > > > >
>> > > > > > > In commit 4346df3392c0 ("phy: atheros: Make RGMII Tx delays actually
>> > > > > > > configurable for AR8035") we brought in changes to get in to line with
>> > > > > > > upstream linux kernel support for this PHY and in turn deal with more
>> > > > > > > "driver was wrong, DT was wrong too" changes. Now the problem I have is
>> > > > > > > that ethernet on my Hummingboard doesn't work AND as far as I can tell,
>> > > > > > > the DTB is correct and saying phy-mode = "rgmii-id" now not "rgmii". It
>> > > > > > > also looks to match what's in v5.7 for the kernel. What do I need to do
>> > > > > > > here next? Thanks!
>> > > > > > >
>> > > > > > > --
>> > > > > > > Tom
>> > > > > >
>> > > > > > Reverting 4346df3392c0 makes your interface work?
>> > > > >
>> > > > > Yup.
>> > > > >
>> > > > > > What is the DTS path that your hummingboard uses?
>> > > > >
>> > > > > Good question. Per board/solidrun/mx6cuboxi/mx6cuboxi.c:
>> > > > > /*
>> > > > > * This is not a perfect match. Avoid dependency on the DM GPIO driver
>> > > > > * needed
>> > > > > * for accurate board detection. Hummingboard2 DT is good enough for
>> > > > > * U-Boot on
>> > > > > * all Hummingboard/Cubox-i platforms.
>> > > > > */
>> > > > > so arch/arm/dts/imx6dl-hummingboard2-emmc-som-v15.dts is the base. But
>> > > > > the board really is the original hummingboard platform. Thanks!
>> > > > >
>> > > > > --
>> > > > > Tom
>> > > >
>> > > > Does it work if you say PHY_INTERFACE_MODE_RGMII_ID here?
>> > > > https://gitlab.denx.de/u-boot/u-boot/-/blob/master/drivers/net/fec_mxc.c#L1232
>> > >
>> > > No change. And to be clear, I bisect'd the issue down and at that
>> > > commit, reverting it fixes ethernet. It doesn't revert cleanly (nor
>> > > obviously to me) on master.
>> > >
>> > > --
>> > > Tom
>> >
>> > On master, the revert would look like this:
>> >
>> > diff --git a/drivers/net/phy/atheros.c b/drivers/net/phy/atheros.c
>> > index 13f7275d1706..5ba639e8119f 100644
>> > --- a/drivers/net/phy/atheros.c
>> > +++ b/drivers/net/phy/atheros.c
>> > @@ -124,6 +124,7 @@ static int ar8021_config(struct phy_device *phydev)
>> >
>> > static int ar803x_delay_config(struct phy_device *phydev)
>> > {
>> > + int regval;
>> > int ret;
>> >
>> > if (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID ||
>> > @@ -138,6 +139,10 @@ static int ar803x_delay_config(struct phy_device *phydev)
>> > else
>> > ret = ar803x_enable_rx_delay(phydev, false);
>> >
>> > + phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
>> > + regval = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
>> > + phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, (regval|0x0100));
>> > +
>> > return ret;
>> > }
>>
>> This alone is not enough.
>>
>
> So if this is not enough, then I'd go back to bisecting. I'd rebase
> right after 8737c65fe4e3 ("phy: atheros: consolidate
> {ar8031|ar8035}_config()"), create a new patch on
> board/solidrun/mx6cuboxi/mx6cuboxi.c which changes RGMII to RGMII_ID,
> confirm it works (according to what you've said so far, it should),
> then bless it as "git bisect good", and let the fun start :)
If these are the correct schematics, it looks like you also need the
rgmii clock:
https://developer.solid-run.com/download/i-mx6-som-simplified-schematics-rev-1-5/
https://gitlab.denx.de/u-boot/u-boot/-/commit/6333cbb3817ed551cd7d4e92f7359c73ccc567fc
So I guess you'd need both, the clock output and the correct RGMII pad
delay.
-michael
next prev parent reply other threads:[~2020-06-17 7:19 UTC|newest]
Thread overview: 49+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-06-16 19:55 U-Boot atheros PHY support and cubox ethernet Tom Rini
2020-06-16 19:58 ` Vladimir Oltean
2020-06-16 20:10 ` Tom Rini
2020-06-16 20:21 ` Vladimir Oltean
2020-06-16 20:31 ` Tom Rini
2020-06-16 20:37 ` Vladimir Oltean
2020-06-16 21:35 ` Tom Rini
2020-06-16 21:57 ` Vladimir Oltean
2020-06-17 7:19 ` Michael Walle [this message]
2020-06-16 21:30 ` Michael Walle
2020-06-16 21:37 ` Tom Rini
2020-06-16 20:42 ` Fabio Estevam
2020-06-16 20:48 ` Vladimir Oltean
2020-06-16 20:51 ` Tom Rini
2020-06-16 20:55 ` Fabio Estevam
2020-06-16 20:58 ` Tom Rini
2020-06-16 21:01 ` Fabio Estevam
2020-06-16 22:30 ` Tom Rini
2020-06-17 12:04 ` Fabio Estevam
2020-06-17 13:06 ` Fabio Estevam
2020-06-17 13:23 ` Tom Rini
2020-06-17 17:31 ` Fabio Estevam
2020-06-17 19:00 ` Tom Rini
2020-06-17 19:09 ` Fabio Estevam
2020-06-17 19:18 ` Fabio Estevam
2020-06-17 19:24 ` Tom Rini
2020-06-17 19:19 ` Tom Rini
2020-06-17 21:28 ` Fabio Estevam
2020-06-17 21:30 ` Tom Rini
2020-06-18 0:41 ` Fabio Estevam
2020-06-18 13:39 ` Tom Rini
2020-06-20 2:14 ` Fabio Estevam
2020-06-24 19:20 ` Soeren Moch
2020-06-24 19:39 ` Fabio Estevam
2020-06-24 20:13 ` Soeren Moch
2020-06-24 20:29 ` Fabio Estevam
2020-06-24 20:45 ` Sören Moch
2020-06-24 21:35 ` Fabio Estevam
2020-06-24 22:29 ` Soeren Moch
2020-06-24 23:19 ` Fabio Estevam
2020-06-24 23:44 ` Fabio Estevam
2020-06-25 9:56 ` Soeren Moch
2020-06-25 10:26 ` Fabio Estevam
2020-06-18 3:05 ` Fabio Estevam
2020-06-16 21:01 ` Vladimir Oltean
2020-06-16 21:04 ` Vladimir Oltean
2020-06-16 21:57 ` Tom Rini
2020-06-16 21:59 ` Vladimir Oltean
2020-06-16 21:50 ` Tom Rini
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=8dc08cb43e9ff3cfb3ade9d91f8d4d61@walle.cc \
--to=michael@walle.cc \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox