Re: 2.6.17-mm6

["J.A. Magallón" <jamagallon@ono.com>]

On Wed, 5 Jul 2006 15:56:02 -0700, Andrew Morton <akpm@osdl.org> wrote:

> "J.A. Magallón" <jamagallon@ono.com> wrote:
> >
> > On Mon, 3 Jul 2006 03:03:55 -0700, Andrew Morton <akpm@osdl.org> wrote:
> > 
> > > 
> > > ftp://ftp.kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.17/2.6.17-mm6/
> > > 
> > > 
> > > - A major update to the e1000 driver.
> > > 
> > 
> > Doesn't find my root drive :(.
> > 
> > Its a SATA drive, on PIIX.
> > Last -mm I tried ('cause of the raid problems) was -mm1, so I don't know
> > when did this broke. Under -mm1, the disk is this:
> > 
> > libata version 1.30 loaded.
> > ata_piix 0000:00:1f.2: version 1.10tj1ac3
> > ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
> > ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 16
> > PCI: Setting latency timer of device 0000:00:1f.2 to 64
> > ata1: SATA max UDMA/133 cmd 0xC000 ctl 0xC402 bmdma 0xD000 irq 16
> > ata2: SATA max UDMA/133 cmd 0xC800 ctl 0xCC02 bmdma 0xD008 irq 16
> > scsi0 : ata_piix
> > ata1: ENTER, pcs=0x13 base=0
> > ata1: LEAVE, pcs=0x13 present_mask=0x1
> > ata1.00: cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003 88:407f
> > ata1.00: ATA-6, max UDMA/133, 390721968 sectors: LBA48 
> > ata1.00: configured for UDMA/133
> > scsi1 : ata_piix
> > ata2: ENTER, pcs=0x13 base=2
> > ata2: LEAVE, pcs=0x11 present_mask=0x0
> > ata2: SATA port has no device.
> >   Vendor: ATA       Model: ST3200822AS       Rev: 3.01
> >   Type:   Direct-Access                      ANSI SCSI revision: 05
> > SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB)
> > sda: Write Protect is off
> > sda: Mode Sense: 00 3a 00 00
> > SCSI device sda: drive cache: write back
> > SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB)
> > sda: Write Protect is off
> > sda: Mode Sense: 00 3a 00 00
> > SCSI device sda: drive cache: write back
> >  sda: sda1 sda2 sda3
> > sd 0:0:0:0: Attached scsi disk sda
> > 
> > With -mm6, the kernel doesn't find it. I get this on boot:
> > 
> > kinit: try_name sda,1 = dev(8,1)
> > kinit: name_to_dev_t(/dev/sda1) = dev(8.1)
> > kinit: root_dev = dev(8,1)
> > kinit: failed to identify filesystem /dev/root, trying all
> > kinit: trying to mount /dev/root on /root with type ext3
> > kinit: Cannot open root device dev(8,1)
> > 
> > I have tried to get this message from -mm1, but could not get it in any log.
> > But... I remember to see that the boot message is like:
> > 
> > kinit: try_name sda,1 = sda1(8,1)
> >                         ^^^^
> > I have verified I built -mm6 with ext3,sata-piix and so on, all builtin.
> > 
> 
> Are you able to test just 2.6.17 + origin.patch + git-libata-all.patch?
> 
> Also, the full dmesg from 2.6.17-mm6 would help, thanks.
> 

It does not reach a point to save the dmesg....
I can pick my digital camera.
Is there a netconsole version for OSX (to attach my ibook and dump dmesg...) ?

--
J.A. Magallon <jamagallon()ono!com>     \               Software is like sex:
                                         \         It's better when it's free
Mandriva Linux release 2007.0 (Cooker) for i586
Linux 2.6.17-jam01 (gcc 4.1.1 20060518 (prerelease)) #2 SMP PREEMPT Wed