From: Udit Kumar <u-kumar1@ti.com>
To: <linux-arm-kernel@lists.infradead.org>, <afd@ti.com>, <bb@ti.com>,
<vaishnav.a@ti.com>, <j-choudhary@ti.com>,
<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
<nm@ti.com>, <vigneshr@ti.com>, <kristo@kernel.org>,
<robh+dt@kernel.org>, <krzysztof.kozlowski+dt@linaro.org>,
<a-govindraju@ti.com>, <kishon@ti.com>
Cc: Udit Kumar <u-kumar1@ti.com>, J Keerthi <j-keerthy@ti.com>
Subject: [PATCH 1/2] arm64: dts: ti: k3-j7200: Fix physical address of pin
Date: Fri, 14 Apr 2023 23:44:33 +0530 [thread overview]
Message-ID: <20230414181434.2046049-2-u-kumar1@ti.com> (raw)
In-Reply-To: <20230414181434.2046049-1-u-kumar1@ti.com>
Fixes: 9ae21ac445e9 ("arm64: dts: ti: k3-j7200: Fix wakeup pinmux range")
wkup_pmx splits into multiple regions. Like
wkup_pmx0 -> 13 pins (WKUP_PADCONFIG 0 - 12)
wkup_pmx1 -> 2 pins (WKUP_PADCONFIG 14 - 15)
wkup_pmx2 -> 59 pins (WKUP_PADCONFIG 26 - 84)
wkup_pmx3 -> 8 pins (WKUP_PADCONFIG 93 - 100)
With this split, pin offset needs to be adjusted to
match with new pmx for all pins above wkup_pmx0.
Example a pin under wkup_pmx1 should start from 0 instead of
old offset(0x38 WKUP_PADCONFIG 14 offset)
J7200 Datasheet (Table 6-106, Section 6.4 Pin Multiplexing) :
https://www.ti.com/lit/ds/symlink/dra821u.pdf
Signed-off-by: J Keerthi <j-keerthy@ti.com>
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
---
.../dts/ti/k3-j7200-common-proc-board.dts | 28 +++++++++----------
1 file changed, 14 insertions(+), 14 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
index 0d39d6b8cc0c..63633e4f6c59 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
@@ -83,25 +83,25 @@ vdd_sd_dv: gpio-regulator-TLV71033 {
&wkup_pmx2 {
mcu_cpsw_pins_default: mcu-cpsw-pins-default {
pinctrl-single,pins = <
- J721E_WKUP_IOPAD(0x0068, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
- J721E_WKUP_IOPAD(0x006c, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */
- J721E_WKUP_IOPAD(0x0070, PIN_OUTPUT, 0) /* MCU_RGMII1_TD3 */
- J721E_WKUP_IOPAD(0x0074, PIN_OUTPUT, 0) /* MCU_RGMII1_TD2 */
- J721E_WKUP_IOPAD(0x0078, PIN_OUTPUT, 0) /* MCU_RGMII1_TD1 */
- J721E_WKUP_IOPAD(0x007c, PIN_OUTPUT, 0) /* MCU_RGMII1_TD0 */
- J721E_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */
- J721E_WKUP_IOPAD(0x008c, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */
- J721E_WKUP_IOPAD(0x0090, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */
- J721E_WKUP_IOPAD(0x0094, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */
- J721E_WKUP_IOPAD(0x0080, PIN_OUTPUT, 0) /* MCU_RGMII1_TXC */
- J721E_WKUP_IOPAD(0x0084, PIN_INPUT, 0) /* MCU_RGMII1_RXC */
+ J721E_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
+ J721E_WKUP_IOPAD(0x0004, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */
+ J721E_WKUP_IOPAD(0x0008, PIN_OUTPUT, 0) /* MCU_RGMII1_TD3 */
+ J721E_WKUP_IOPAD(0x000c, PIN_OUTPUT, 0) /* MCU_RGMII1_TD2 */
+ J721E_WKUP_IOPAD(0x0010, PIN_OUTPUT, 0) /* MCU_RGMII1_TD1 */
+ J721E_WKUP_IOPAD(0x0014, PIN_OUTPUT, 0) /* MCU_RGMII1_TD0 */
+ J721E_WKUP_IOPAD(0x0020, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */
+ J721E_WKUP_IOPAD(0x0024, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */
+ J721E_WKUP_IOPAD(0x0028, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */
+ J721E_WKUP_IOPAD(0x002c, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */
+ J721E_WKUP_IOPAD(0x0018, PIN_OUTPUT, 0) /* MCU_RGMII1_TXC */
+ J721E_WKUP_IOPAD(0x001c, PIN_INPUT, 0) /* MCU_RGMII1_RXC */
>;
};
mcu_mdio_pins_default: mcu-mdio1-pins-default {
pinctrl-single,pins = <
- J721E_WKUP_IOPAD(0x009c, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */
- J721E_WKUP_IOPAD(0x0098, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
+ J721E_WKUP_IOPAD(0x0034, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */
+ J721E_WKUP_IOPAD(0x0030, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
>;
};
};
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
WARNING: multiple messages have this Message-ID (diff)
From: Udit Kumar <u-kumar1@ti.com>
To: <linux-arm-kernel@lists.infradead.org>, <afd@ti.com>, <bb@ti.com>,
<vaishnav.a@ti.com>, <j-choudhary@ti.com>,
<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
<nm@ti.com>, <vigneshr@ti.com>, <kristo@kernel.org>,
<robh+dt@kernel.org>, <krzysztof.kozlowski+dt@linaro.org>,
<a-govindraju@ti.com>, <kishon@ti.com>
Cc: Udit Kumar <u-kumar1@ti.com>, J Keerthi <j-keerthy@ti.com>
Subject: [PATCH 1/2] arm64: dts: ti: k3-j7200: Fix physical address of pin
Date: Fri, 14 Apr 2023 23:44:33 +0530 [thread overview]
Message-ID: <20230414181434.2046049-2-u-kumar1@ti.com> (raw)
In-Reply-To: <20230414181434.2046049-1-u-kumar1@ti.com>
Fixes: 9ae21ac445e9 ("arm64: dts: ti: k3-j7200: Fix wakeup pinmux range")
wkup_pmx splits into multiple regions. Like
wkup_pmx0 -> 13 pins (WKUP_PADCONFIG 0 - 12)
wkup_pmx1 -> 2 pins (WKUP_PADCONFIG 14 - 15)
wkup_pmx2 -> 59 pins (WKUP_PADCONFIG 26 - 84)
wkup_pmx3 -> 8 pins (WKUP_PADCONFIG 93 - 100)
With this split, pin offset needs to be adjusted to
match with new pmx for all pins above wkup_pmx0.
Example a pin under wkup_pmx1 should start from 0 instead of
old offset(0x38 WKUP_PADCONFIG 14 offset)
J7200 Datasheet (Table 6-106, Section 6.4 Pin Multiplexing) :
https://www.ti.com/lit/ds/symlink/dra821u.pdf
Signed-off-by: J Keerthi <j-keerthy@ti.com>
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
---
.../dts/ti/k3-j7200-common-proc-board.dts | 28 +++++++++----------
1 file changed, 14 insertions(+), 14 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
index 0d39d6b8cc0c..63633e4f6c59 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
@@ -83,25 +83,25 @@ vdd_sd_dv: gpio-regulator-TLV71033 {
&wkup_pmx2 {
mcu_cpsw_pins_default: mcu-cpsw-pins-default {
pinctrl-single,pins = <
- J721E_WKUP_IOPAD(0x0068, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
- J721E_WKUP_IOPAD(0x006c, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */
- J721E_WKUP_IOPAD(0x0070, PIN_OUTPUT, 0) /* MCU_RGMII1_TD3 */
- J721E_WKUP_IOPAD(0x0074, PIN_OUTPUT, 0) /* MCU_RGMII1_TD2 */
- J721E_WKUP_IOPAD(0x0078, PIN_OUTPUT, 0) /* MCU_RGMII1_TD1 */
- J721E_WKUP_IOPAD(0x007c, PIN_OUTPUT, 0) /* MCU_RGMII1_TD0 */
- J721E_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */
- J721E_WKUP_IOPAD(0x008c, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */
- J721E_WKUP_IOPAD(0x0090, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */
- J721E_WKUP_IOPAD(0x0094, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */
- J721E_WKUP_IOPAD(0x0080, PIN_OUTPUT, 0) /* MCU_RGMII1_TXC */
- J721E_WKUP_IOPAD(0x0084, PIN_INPUT, 0) /* MCU_RGMII1_RXC */
+ J721E_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
+ J721E_WKUP_IOPAD(0x0004, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */
+ J721E_WKUP_IOPAD(0x0008, PIN_OUTPUT, 0) /* MCU_RGMII1_TD3 */
+ J721E_WKUP_IOPAD(0x000c, PIN_OUTPUT, 0) /* MCU_RGMII1_TD2 */
+ J721E_WKUP_IOPAD(0x0010, PIN_OUTPUT, 0) /* MCU_RGMII1_TD1 */
+ J721E_WKUP_IOPAD(0x0014, PIN_OUTPUT, 0) /* MCU_RGMII1_TD0 */
+ J721E_WKUP_IOPAD(0x0020, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */
+ J721E_WKUP_IOPAD(0x0024, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */
+ J721E_WKUP_IOPAD(0x0028, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */
+ J721E_WKUP_IOPAD(0x002c, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */
+ J721E_WKUP_IOPAD(0x0018, PIN_OUTPUT, 0) /* MCU_RGMII1_TXC */
+ J721E_WKUP_IOPAD(0x001c, PIN_INPUT, 0) /* MCU_RGMII1_RXC */
>;
};
mcu_mdio_pins_default: mcu-mdio1-pins-default {
pinctrl-single,pins = <
- J721E_WKUP_IOPAD(0x009c, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */
- J721E_WKUP_IOPAD(0x0098, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
+ J721E_WKUP_IOPAD(0x0034, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */
+ J721E_WKUP_IOPAD(0x0030, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
>;
};
};
--
2.34.1
next prev parent reply other threads:[~2023-04-14 18:15 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-04-14 18:14 [PATCH 0/2] arm64: dts: ti: k3-j7200-common-proc-board fixes Udit Kumar
2023-04-14 18:14 ` Udit Kumar
2023-04-14 18:14 ` Udit Kumar [this message]
2023-04-14 18:14 ` [PATCH 1/2] arm64: dts: ti: k3-j7200: Fix physical address of pin Udit Kumar
2023-04-14 18:26 ` Nishanth Menon
2023-04-14 18:26 ` Nishanth Menon
2023-04-15 4:10 ` Kumar, Udit
2023-04-15 4:10 ` Kumar, Udit
2023-04-15 12:47 ` Nishanth Menon
2023-04-15 12:47 ` Nishanth Menon
2023-04-14 18:14 ` [PATCH 2/2] arm64: dts: ti: k3-j7200-common-proc-board: Enable I2C Udit Kumar
2023-04-14 18:14 ` Udit Kumar
2023-04-14 18:24 ` Nishanth Menon
2023-04-14 18:24 ` Nishanth Menon
2023-04-15 4:06 ` Kumar, Udit
2023-04-15 4:06 ` Kumar, Udit
2023-04-15 12:47 ` Nishanth Menon
2023-04-15 12:47 ` Nishanth Menon
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230414181434.2046049-2-u-kumar1@ti.com \
--to=u-kumar1@ti.com \
--cc=a-govindraju@ti.com \
--cc=afd@ti.com \
--cc=bb@ti.com \
--cc=devicetree@vger.kernel.org \
--cc=j-choudhary@ti.com \
--cc=j-keerthy@ti.com \
--cc=kishon@ti.com \
--cc=kristo@kernel.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=nm@ti.com \
--cc=robh+dt@kernel.org \
--cc=vaishnav.a@ti.com \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.