All of lore.kernel.org
 help / color / mirror / Atom feed
From: Nishanth Menon <nm@ti.com>
To: Udit Kumar <u-kumar1@ti.com>
Cc: <linux-arm-kernel@lists.infradead.org>, <afd@ti.com>, <bb@ti.com>,
	<vaishnav.a@ti.com>, <j-choudhary@ti.com>,
	<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
	<vigneshr@ti.com>, <kristo@kernel.org>, <robh+dt@kernel.org>,
	<krzysztof.kozlowski+dt@linaro.org>, <a-govindraju@ti.com>,
	<kishon@ti.com>, J Keerthi <j-keerthy@ti.com>
Subject: Re: [PATCH 1/2] arm64: dts: ti: k3-j7200: Fix  physical address of pin
Date: Fri, 14 Apr 2023 13:26:38 -0500	[thread overview]
Message-ID: <20230414182638.watc555ihi2hgkuv@slinging> (raw)
In-Reply-To: <20230414181434.2046049-2-u-kumar1@ti.com>

On 23:44-20230414, Udit Kumar wrote:
> Fixes: 9ae21ac445e9 ("arm64: dts: ti: k3-j7200: Fix wakeup pinmux range")

In the wrong place.
> 
> wkup_pmx splits into multiple regions. Like
> 
>     wkup_pmx0 -> 13 pins (WKUP_PADCONFIG 0 - 12)
>     wkup_pmx1 -> 2 pins (WKUP_PADCONFIG 14 - 15)
>     wkup_pmx2 -> 59 pins (WKUP_PADCONFIG 26 - 84)
>     wkup_pmx3 -> 8 pins (WKUP_PADCONFIG 93 - 100)
> 
> With this split, pin offset needs to be adjusted to
> match with new pmx for all pins above wkup_pmx0.
> 
> Example a pin under wkup_pmx1 should start from 0 instead of
> old offset(0x38 WKUP_PADCONFIG 14 offset)
> 
> J7200 Datasheet (Table 6-106, Section 6.4 Pin Multiplexing) :
>             https://www.ti.com/lit/ds/symlink/dra821u.pdf

Drop the preceding whitespace.

> 
> Signed-off-by: J Keerthi <j-keerthy@ti.com>

Spell check name please, I think he usually goes with:

Signed-off-by: Keerthy <j-keerthy@ti.com>

If this patch is from Keerthy, the patch should have a "From:"

> Signed-off-by: Udit Kumar <u-kumar1@ti.com>
> ---
>  .../dts/ti/k3-j7200-common-proc-board.dts     | 28 +++++++++----------
>  1 file changed, 14 insertions(+), 14 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> index 0d39d6b8cc0c..63633e4f6c59 100644
> --- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> +++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> @@ -83,25 +83,25 @@ vdd_sd_dv: gpio-regulator-TLV71033 {
>  &wkup_pmx2 {
>  	mcu_cpsw_pins_default: mcu-cpsw-pins-default {
>  		pinctrl-single,pins = <
> -			J721E_WKUP_IOPAD(0x0068, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
> -			J721E_WKUP_IOPAD(0x006c, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */
> -			J721E_WKUP_IOPAD(0x0070, PIN_OUTPUT, 0) /* MCU_RGMII1_TD3 */
> -			J721E_WKUP_IOPAD(0x0074, PIN_OUTPUT, 0) /* MCU_RGMII1_TD2 */
> -			J721E_WKUP_IOPAD(0x0078, PIN_OUTPUT, 0) /* MCU_RGMII1_TD1 */
> -			J721E_WKUP_IOPAD(0x007c, PIN_OUTPUT, 0) /* MCU_RGMII1_TD0 */
> -			J721E_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */
> -			J721E_WKUP_IOPAD(0x008c, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */
> -			J721E_WKUP_IOPAD(0x0090, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */
> -			J721E_WKUP_IOPAD(0x0094, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */
> -			J721E_WKUP_IOPAD(0x0080, PIN_OUTPUT, 0) /* MCU_RGMII1_TXC */
> -			J721E_WKUP_IOPAD(0x0084, PIN_INPUT, 0) /* MCU_RGMII1_RXC */
> +			J721E_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
> +			J721E_WKUP_IOPAD(0x0004, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */
> +			J721E_WKUP_IOPAD(0x0008, PIN_OUTPUT, 0) /* MCU_RGMII1_TD3 */
> +			J721E_WKUP_IOPAD(0x000c, PIN_OUTPUT, 0) /* MCU_RGMII1_TD2 */
> +			J721E_WKUP_IOPAD(0x0010, PIN_OUTPUT, 0) /* MCU_RGMII1_TD1 */
> +			J721E_WKUP_IOPAD(0x0014, PIN_OUTPUT, 0) /* MCU_RGMII1_TD0 */
> +			J721E_WKUP_IOPAD(0x0020, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */
> +			J721E_WKUP_IOPAD(0x0024, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */
> +			J721E_WKUP_IOPAD(0x0028, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */
> +			J721E_WKUP_IOPAD(0x002c, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */
> +			J721E_WKUP_IOPAD(0x0018, PIN_OUTPUT, 0) /* MCU_RGMII1_TXC */
> +			J721E_WKUP_IOPAD(0x001c, PIN_INPUT, 0) /* MCU_RGMII1_RXC */

nice catch.

>  		>;
>  	};
>  
>  	mcu_mdio_pins_default: mcu-mdio1-pins-default {
>  		pinctrl-single,pins = <
> -			J721E_WKUP_IOPAD(0x009c, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */
> -			J721E_WKUP_IOPAD(0x0098, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
> +			J721E_WKUP_IOPAD(0x0034, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */
> +			J721E_WKUP_IOPAD(0x0030, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
>  		>;
>  	};
>  };
> -- 
> 2.34.1
> 

-- 
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

WARNING: multiple messages have this Message-ID (diff)
From: Nishanth Menon <nm@ti.com>
To: Udit Kumar <u-kumar1@ti.com>
Cc: <linux-arm-kernel@lists.infradead.org>, <afd@ti.com>, <bb@ti.com>,
	<vaishnav.a@ti.com>, <j-choudhary@ti.com>,
	<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
	<vigneshr@ti.com>, <kristo@kernel.org>, <robh+dt@kernel.org>,
	<krzysztof.kozlowski+dt@linaro.org>, <a-govindraju@ti.com>,
	<kishon@ti.com>, J Keerthi <j-keerthy@ti.com>
Subject: Re: [PATCH 1/2] arm64: dts: ti: k3-j7200: Fix  physical address of pin
Date: Fri, 14 Apr 2023 13:26:38 -0500	[thread overview]
Message-ID: <20230414182638.watc555ihi2hgkuv@slinging> (raw)
In-Reply-To: <20230414181434.2046049-2-u-kumar1@ti.com>

On 23:44-20230414, Udit Kumar wrote:
> Fixes: 9ae21ac445e9 ("arm64: dts: ti: k3-j7200: Fix wakeup pinmux range")

In the wrong place.
> 
> wkup_pmx splits into multiple regions. Like
> 
>     wkup_pmx0 -> 13 pins (WKUP_PADCONFIG 0 - 12)
>     wkup_pmx1 -> 2 pins (WKUP_PADCONFIG 14 - 15)
>     wkup_pmx2 -> 59 pins (WKUP_PADCONFIG 26 - 84)
>     wkup_pmx3 -> 8 pins (WKUP_PADCONFIG 93 - 100)
> 
> With this split, pin offset needs to be adjusted to
> match with new pmx for all pins above wkup_pmx0.
> 
> Example a pin under wkup_pmx1 should start from 0 instead of
> old offset(0x38 WKUP_PADCONFIG 14 offset)
> 
> J7200 Datasheet (Table 6-106, Section 6.4 Pin Multiplexing) :
>             https://www.ti.com/lit/ds/symlink/dra821u.pdf

Drop the preceding whitespace.

> 
> Signed-off-by: J Keerthi <j-keerthy@ti.com>

Spell check name please, I think he usually goes with:

Signed-off-by: Keerthy <j-keerthy@ti.com>

If this patch is from Keerthy, the patch should have a "From:"

> Signed-off-by: Udit Kumar <u-kumar1@ti.com>
> ---
>  .../dts/ti/k3-j7200-common-proc-board.dts     | 28 +++++++++----------
>  1 file changed, 14 insertions(+), 14 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> index 0d39d6b8cc0c..63633e4f6c59 100644
> --- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> +++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> @@ -83,25 +83,25 @@ vdd_sd_dv: gpio-regulator-TLV71033 {
>  &wkup_pmx2 {
>  	mcu_cpsw_pins_default: mcu-cpsw-pins-default {
>  		pinctrl-single,pins = <
> -			J721E_WKUP_IOPAD(0x0068, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
> -			J721E_WKUP_IOPAD(0x006c, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */
> -			J721E_WKUP_IOPAD(0x0070, PIN_OUTPUT, 0) /* MCU_RGMII1_TD3 */
> -			J721E_WKUP_IOPAD(0x0074, PIN_OUTPUT, 0) /* MCU_RGMII1_TD2 */
> -			J721E_WKUP_IOPAD(0x0078, PIN_OUTPUT, 0) /* MCU_RGMII1_TD1 */
> -			J721E_WKUP_IOPAD(0x007c, PIN_OUTPUT, 0) /* MCU_RGMII1_TD0 */
> -			J721E_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */
> -			J721E_WKUP_IOPAD(0x008c, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */
> -			J721E_WKUP_IOPAD(0x0090, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */
> -			J721E_WKUP_IOPAD(0x0094, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */
> -			J721E_WKUP_IOPAD(0x0080, PIN_OUTPUT, 0) /* MCU_RGMII1_TXC */
> -			J721E_WKUP_IOPAD(0x0084, PIN_INPUT, 0) /* MCU_RGMII1_RXC */
> +			J721E_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
> +			J721E_WKUP_IOPAD(0x0004, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */
> +			J721E_WKUP_IOPAD(0x0008, PIN_OUTPUT, 0) /* MCU_RGMII1_TD3 */
> +			J721E_WKUP_IOPAD(0x000c, PIN_OUTPUT, 0) /* MCU_RGMII1_TD2 */
> +			J721E_WKUP_IOPAD(0x0010, PIN_OUTPUT, 0) /* MCU_RGMII1_TD1 */
> +			J721E_WKUP_IOPAD(0x0014, PIN_OUTPUT, 0) /* MCU_RGMII1_TD0 */
> +			J721E_WKUP_IOPAD(0x0020, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */
> +			J721E_WKUP_IOPAD(0x0024, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */
> +			J721E_WKUP_IOPAD(0x0028, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */
> +			J721E_WKUP_IOPAD(0x002c, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */
> +			J721E_WKUP_IOPAD(0x0018, PIN_OUTPUT, 0) /* MCU_RGMII1_TXC */
> +			J721E_WKUP_IOPAD(0x001c, PIN_INPUT, 0) /* MCU_RGMII1_RXC */

nice catch.

>  		>;
>  	};
>  
>  	mcu_mdio_pins_default: mcu-mdio1-pins-default {
>  		pinctrl-single,pins = <
> -			J721E_WKUP_IOPAD(0x009c, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */
> -			J721E_WKUP_IOPAD(0x0098, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
> +			J721E_WKUP_IOPAD(0x0034, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */
> +			J721E_WKUP_IOPAD(0x0030, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
>  		>;
>  	};
>  };
> -- 
> 2.34.1
> 

-- 
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D

  reply	other threads:[~2023-04-14 18:27 UTC|newest]

Thread overview: 18+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-04-14 18:14 [PATCH 0/2] arm64: dts: ti: k3-j7200-common-proc-board fixes Udit Kumar
2023-04-14 18:14 ` Udit Kumar
2023-04-14 18:14 ` [PATCH 1/2] arm64: dts: ti: k3-j7200: Fix physical address of pin Udit Kumar
2023-04-14 18:14   ` Udit Kumar
2023-04-14 18:26   ` Nishanth Menon [this message]
2023-04-14 18:26     ` Nishanth Menon
2023-04-15  4:10     ` Kumar, Udit
2023-04-15  4:10       ` Kumar, Udit
2023-04-15 12:47       ` Nishanth Menon
2023-04-15 12:47         ` Nishanth Menon
2023-04-14 18:14 ` [PATCH 2/2] arm64: dts: ti: k3-j7200-common-proc-board: Enable I2C Udit Kumar
2023-04-14 18:14   ` Udit Kumar
2023-04-14 18:24   ` Nishanth Menon
2023-04-14 18:24     ` Nishanth Menon
2023-04-15  4:06     ` Kumar, Udit
2023-04-15  4:06       ` Kumar, Udit
2023-04-15 12:47       ` Nishanth Menon
2023-04-15 12:47         ` Nishanth Menon

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20230414182638.watc555ihi2hgkuv@slinging \
    --to=nm@ti.com \
    --cc=a-govindraju@ti.com \
    --cc=afd@ti.com \
    --cc=bb@ti.com \
    --cc=devicetree@vger.kernel.org \
    --cc=j-choudhary@ti.com \
    --cc=j-keerthy@ti.com \
    --cc=kishon@ti.com \
    --cc=kristo@kernel.org \
    --cc=krzysztof.kozlowski+dt@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=robh+dt@kernel.org \
    --cc=u-kumar1@ti.com \
    --cc=vaishnav.a@ti.com \
    --cc=vigneshr@ti.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.