* [PATCH 1/7] sunxi: add support for the Allwinner B288
2026-10-16 9:16 [PATCH 0/7] sunxi: add the Allwinner B288 and the PocketBook Verse Pablo Mazzini
@ 2026-10-16 9:16 ` Pablo Mazzini
2026-10-16 9:16 ` [PATCH 2/7] sunxi: dram: support " Pablo Mazzini
` (6 subsequent siblings)
7 siblings, 0 replies; 10+ messages in thread
From: Pablo Mazzini @ 2026-10-16 9:16 UTC (permalink / raw)
To: Andre Przywara, u-boot; +Cc: Tom Rini, linux-sunxi, Ilias Apalodimas
The B288 is a dual Cortex-A7 SoC of the sun8i family, used in e-readers.
Its memory map follows the H3, but the RTC, CPUCFG and SID sit where the
A20 has them, and there is no SRAM A2.
Signed-off-by: Pablo Mazzini <pmazzini@gmail.com>
---
arch/arm/cpu/armv7/sunxi/psci.c | 9 +++++++--
arch/arm/include/asm/arch-sunxi/cpu.h | 1 +
arch/arm/include/asm/arch-sunxi/cpu_sun4i.h | 16 +++++++++++++---
arch/arm/mach-sunxi/Kconfig | 13 +++++++++++++
arch/arm/mach-sunxi/board.c | 4 ++++
arch/arm/mach-sunxi/clock_sun6i.c | 1 +
arch/arm/mach-sunxi/cpu_info.c | 2 ++
include/sunxi_gpio.h | 1 +
8 files changed, 42 insertions(+), 5 deletions(-)
diff --git a/arch/arm/cpu/armv7/sunxi/psci.c b/arch/arm/cpu/armv7/sunxi/psci.c
index 4c30f3294b7..18a93546f16 100644
--- a/arch/arm/cpu/armv7/sunxi/psci.c
+++ b/arch/arm/cpu/armv7/sunxi/psci.c
@@ -53,6 +53,7 @@
* CPU state, rather than the older CPUCFG system.
*/
#define SUN8I_R528_SOFT_ENTRY (0x1c8)
+#define SUN8I_B288_SOFT_ENTRY (0x1e4)
#define SUN8I_R528_C0_RST_CTRL (0x0000)
#define SUN8I_R528_C0_CTRL_REG0 (0x0010)
#define SUN8I_R528_C0_CPU_STATUS (0x0080)
@@ -126,6 +127,9 @@ static void __secure sunxi_cpu_set_entry(int __always_unused cpu, void *entry)
} else if (IS_ENABLED(CONFIG_MACH_SUN8I_R528)) {
writel((u32)entry,
SUNXI_R_CPUCFG_BASE + SUN8I_R528_SOFT_ENTRY);
+ } else if (IS_ENABLED(CONFIG_MACH_SUN8I_B288)) {
+ /* the B288 BROM takes the secondary entry from the RTC */
+ writel((u32)entry, SUNXI_RTC_BASE + SUN8I_B288_SOFT_ENTRY);
} else {
writel((u32)entry, SUNXI_CPUCFG_BASE + SUNXI_PRIV0);
}
@@ -144,8 +148,9 @@ static void __secure sunxi_cpu_set_power(int cpu, bool on)
} else if (IS_ENABLED(CONFIG_MACH_SUN8I_R40)) {
clamp = (void *)SUNXI_CPUCFG_BASE + SUN8I_R40_PWR_CLAMP(cpu);
pwroff = (void *)SUNXI_CPUCFG_BASE + SUN8I_R40_PWROFF;
- } else if (IS_ENABLED(CONFIG_MACH_SUN8I_R528)) {
- /* R528 leaves both cores powered up, manages them via reset */
+ } else if (IS_ENABLED(CONFIG_MACH_SUN8I_R528) ||
+ IS_ENABLED(CONFIG_MACH_SUN8I_B288)) {
+ /* Both leave the cores powered and manage them via reset */
return;
} else {
if (IS_ENABLED(CONFIG_MACH_SUN6I) ||
diff --git a/arch/arm/include/asm/arch-sunxi/cpu.h b/arch/arm/include/asm/arch-sunxi/cpu.h
index 768c6572d6b..7515d98959d 100644
--- a/arch/arm/include/asm/arch-sunxi/cpu.h
+++ b/arch/arm/include/asm/arch-sunxi/cpu.h
@@ -21,5 +21,6 @@
#define SOCID_V3S 0x1681
#define SOCID_H5 0x1718
#define SOCID_R40 0x1701
+#define SOCID_B288 0x1699
#endif /* _SUNXI_CPU_H */
diff --git a/arch/arm/include/asm/arch-sunxi/cpu_sun4i.h b/arch/arm/include/asm/arch-sunxi/cpu_sun4i.h
index f023a4cfd93..559544daf58 100644
--- a/arch/arm/include/asm/arch-sunxi/cpu_sun4i.h
+++ b/arch/arm/include/asm/arch-sunxi/cpu_sun4i.h
@@ -13,7 +13,8 @@
#if defined(CONFIG_SUNXI_GEN_SUN6I) && \
!defined(CONFIG_MACH_SUN8I_R40) && \
- !defined(CONFIG_MACH_SUN8I_V3S)
+ !defined(CONFIG_MACH_SUN8I_V3S) && \
+ !defined(CONFIG_MACH_SUN8I_B288)
#define SUNXI_SRAM_A2_BASE 0x00040000
#ifdef CONFIG_MACH_SUN8I_H3
#define SUNXI_SRAM_A2_SIZE (48 * 1024) /* 16+32 kiB */
@@ -77,6 +78,9 @@ defined(CONFIG_MACH_SUN50I)
/* SID address space starts at 0x01c1400, but e-fuse is at offset 0x200 */
#define SUNXI_SIDC_BASE 0x01c14000
#define SUNXI_SID_BASE 0x01c14200
+#elif defined(CONFIG_MACH_SUN8I_B288)
+/* The H3's SID address, but with the e-fuse at offset 0, as on the A10 */
+#define SUNXI_SID_BASE 0x01c14000
#else
#define SUNXI_SID_BASE 0x01c23800
#endif
@@ -86,7 +90,8 @@ defined(CONFIG_MACH_SUN50I)
#define SUNXI_TP_BASE 0x01c25000
#define SUNXI_PMU_BASE 0x01c25400
-#if defined CONFIG_MACH_SUN7I || defined CONFIG_MACH_SUN8I_R40
+#if defined CONFIG_MACH_SUN7I || defined CONFIG_MACH_SUN8I_R40 || \
+ defined CONFIG_MACH_SUN8I_B288
#define SUNXI_CPUCFG_BASE 0x01c25c00
#endif
@@ -144,12 +149,17 @@ defined(CONFIG_MACH_SUN50I)
#define SUNXI_HDMI_BASE 0x01ee0000
#endif
+#ifdef CONFIG_MACH_SUN8I_B288
+#define SUNXI_RTC_BASE 0x01c20400
+#else
#define SUNXI_RTC_BASE 0x01f00000
+#endif
#define SUNXI_PRCM_BASE 0x01f01400
#if defined CONFIG_SUNXI_GEN_SUN6I && \
!defined CONFIG_MACH_SUN8I_A83T && \
- !defined CONFIG_MACH_SUN8I_R40
+ !defined CONFIG_MACH_SUN8I_R40 && \
+ !defined CONFIG_MACH_SUN8I_B288
#define SUNXI_CPUCFG_BASE 0x01f01c00
#endif
diff --git a/arch/arm/mach-sunxi/Kconfig b/arch/arm/mach-sunxi/Kconfig
index b0c5d3cd903..ed2402f71f2 100644
--- a/arch/arm/mach-sunxi/Kconfig
+++ b/arch/arm/mach-sunxi/Kconfig
@@ -490,6 +490,18 @@ config MACH_SUN8I_R528
select DRAM_SUN20I_D1
imply OF_UPSTREAM
+config MACH_SUN8I_B288
+ bool "sun8i (Allwinner B288)"
+ select CPU_V7A
+ select CPU_V7_HAS_NONSEC
+ select CPU_V7_HAS_VIRT
+ select ARCH_SUPPORT_PSCI
+ select SUNXI_GEN_SUN6I
+ select SUNXI_DRAM_DW
+ select SUNXI_DRAM_DW_32BIT
+ select SUPPORT_SPL
+ imply OF_UPSTREAM
+
config MACH_SUN8I_V3S
bool "sun8i (Allwinner V3/V3s/S3/S3L)"
select CPU_V7A
@@ -579,6 +591,7 @@ config MACH_SUN8I
default y if MACH_SUNXI_H3_H5
default y if MACH_SUN8I_R40
default y if MACH_SUN8I_V3S
+ default y if MACH_SUN8I_B288
config RESERVE_ALLWINNER_BOOT0_HEADER
bool "reserve space for Allwinner boot0 header"
diff --git a/arch/arm/mach-sunxi/board.c b/arch/arm/mach-sunxi/board.c
index 432b1c10f92..c2b01896da9 100644
--- a/arch/arm/mach-sunxi/board.c
+++ b/arch/arm/mach-sunxi/board.c
@@ -153,6 +153,10 @@ static int gpio_init(void)
sunxi_gpio_set_cfgpin(SUNXI_GPB(8), SUN8I_V3S_GPB_UART0);
sunxi_gpio_set_cfgpin(SUNXI_GPB(9), SUN8I_V3S_GPB_UART0);
sunxi_gpio_set_pull(SUNXI_GPB(9), SUNXI_GPIO_PULL_UP);
+#elif CONFIG_CONS_INDEX == 1 && defined(CONFIG_MACH_SUN8I_B288)
+ sunxi_gpio_set_cfgpin(SUNXI_GPB(4), SUN8I_B288_GPB_UART0);
+ sunxi_gpio_set_cfgpin(SUNXI_GPB(5), SUN8I_B288_GPB_UART0);
+ sunxi_gpio_set_pull(SUNXI_GPB(5), SUNXI_GPIO_PULL_UP);
#elif CONFIG_CONS_INDEX == 1 && defined(CONFIG_MACH_SUN9I)
sunxi_gpio_set_cfgpin(SUNXI_GPH(12), SUN9I_GPH_UART0);
sunxi_gpio_set_cfgpin(SUNXI_GPH(13), SUN9I_GPH_UART0);
diff --git a/arch/arm/mach-sunxi/clock_sun6i.c b/arch/arm/mach-sunxi/clock_sun6i.c
index 657736c7ac2..d8e549a0adb 100644
--- a/arch/arm/mach-sunxi/clock_sun6i.c
+++ b/arch/arm/mach-sunxi/clock_sun6i.c
@@ -305,6 +305,7 @@ void clock_set_pll10(unsigned int clk)
#if defined(CONFIG_MACH_SUN8I_A33) || \
defined(CONFIG_MACH_SUN8I_R40) || \
+ defined(CONFIG_MACH_SUN8I_B288) || \
defined(CONFIG_MACH_SUN50I)
void clock_set_pll11(unsigned int clk, bool sigma_delta_enable)
{
diff --git a/arch/arm/mach-sunxi/cpu_info.c b/arch/arm/mach-sunxi/cpu_info.c
index c3a51d9956e..7c04105ad6d 100644
--- a/arch/arm/mach-sunxi/cpu_info.c
+++ b/arch/arm/mach-sunxi/cpu_info.c
@@ -86,6 +86,8 @@ int print_cpuinfo(void)
printf("CPU: Allwinner A33 (SUN8I %04x)\n", sunxi_get_sram_id());
#elif defined CONFIG_MACH_SUN8I_A83T
printf("CPU: Allwinner A83T (SUN8I %04x)\n", sunxi_get_sram_id());
+#elif defined CONFIG_MACH_SUN8I_B288
+ printf("CPU: Allwinner B288 (SUN8I %04x)\n", sunxi_get_sram_id());
#elif defined CONFIG_MACH_SUN8I_H3
printf("CPU: Allwinner H3 (SUN8I %04x)\n", sunxi_get_sram_id());
#elif defined CONFIG_MACH_SUN8I_R40
diff --git a/include/sunxi_gpio.h b/include/sunxi_gpio.h
index 12b54c8dda4..ad2bd0470f8 100644
--- a/include/sunxi_gpio.h
+++ b/include/sunxi_gpio.h
@@ -116,6 +116,7 @@ enum sunxi_gpio_number {
#define SUN8I_A33_GPB_UART0 3
#define SUN8I_A83T_GPB_UART0 2
#define SUN8I_V3S_GPB_UART0 3
+#define SUN8I_B288_GPB_UART0 2
#define SUN50I_GPB_UART0 4
#define SUNXI_GPC_NAND 2
--
2.52.0
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH 2/7] sunxi: dram: support the Allwinner B288
2026-10-16 9:16 [PATCH 0/7] sunxi: add the Allwinner B288 and the PocketBook Verse Pablo Mazzini
2026-10-16 9:16 ` [PATCH 1/7] sunxi: add support for the Allwinner B288 Pablo Mazzini
@ 2026-10-16 9:16 ` Pablo Mazzini
2026-10-16 9:16 ` [PATCH 3/7] dt-bindings: clock: add the Allwinner B288 CCU Pablo Mazzini
` (5 subsequent siblings)
7 siblings, 0 replies; 10+ messages in thread
From: Pablo Mazzini @ 2026-10-16 9:16 UTC (permalink / raw)
To: Andre Przywara, u-boot; +Cc: Tom Rini, linux-sunxi, Ilias Apalodimas
The B288 has the DW controller and PHY of the H3, set up as on the H5.
Gate training finds its ranks and bus width, as in the vendor code.
Signed-off-by: Pablo Mazzini <pmazzini@gmail.com>
---
arch/arm/mach-sunxi/Kconfig | 1 +
arch/arm/mach-sunxi/dram_sunxi_dw.c | 97 +++++++++++++++++++++++++----
2 files changed, 86 insertions(+), 12 deletions(-)
diff --git a/arch/arm/mach-sunxi/Kconfig b/arch/arm/mach-sunxi/Kconfig
index ed2402f71f2..0326c7a976b 100644
--- a/arch/arm/mach-sunxi/Kconfig
+++ b/arch/arm/mach-sunxi/Kconfig
@@ -788,6 +788,7 @@ config DRAM_ODT_EN
depends on !MACH_SUN50I_H616
depends on !MACH_SUN55I_A523
default y if MACH_SUN8I_A23
+ default y if MACH_SUN8I_B288
default y if MACH_SUNXI_H3_H5
default y if MACH_SUN8I_R40
default y if MACH_SUN50I
diff --git a/arch/arm/mach-sunxi/dram_sunxi_dw.c b/arch/arm/mach-sunxi/dram_sunxi_dw.c
index 4ed295909ce..ee96186abc6 100644
--- a/arch/arm/mach-sunxi/dram_sunxi_dw.c
+++ b/arch/arm/mach-sunxi/dram_sunxi_dw.c
@@ -21,6 +21,10 @@ static void mctl_phy_init(u32 val)
struct sunxi_mctl_ctl_reg * const mctl_ctl =
(struct sunxi_mctl_ctl_reg *)SUNXI_DRAM_CTL0_BASE;
+ /* the B288 latches the configuration before triggering */
+ if (IS_ENABLED(CONFIG_MACH_SUN8I_B288))
+ writel(val, &mctl_ctl->pir);
+
writel(val | PIR_INIT, &mctl_ctl->pir);
mctl_await_completion(&mctl_ctl->pgsr[0], PGSR_INIT_DONE, 0x1);
}
@@ -48,6 +52,11 @@ static void mctl_set_bit_delays(struct dram_para *para)
for (i = 0; i < 4; i++)
writel(0x6 << 24, &mctl_ctl->dx[i].sdlr);
#endif
+ if (IS_ENABLED(CONFIG_MACH_SUN8I_B288)) {
+ /* boot0 uses 8 on DX0/DX1 and 6 on DX2/DX3 */
+ for (i = 0; i < 4; i++)
+ writel((i < 2 ? 0x8 : 0x6) << 24, &mctl_ctl->dx[i].sdlr);
+ }
setbits_le32(&mctl_ctl->pgcr[0], 1 << 26);
}
@@ -248,9 +257,24 @@ static void mctl_set_master_priority_r40(void)
MBUS_CONF(UNKNOWN3, true, HIGH, 0, 1280, 144, 64);
}
+/*
+ * The B288 boot0 only sets the MBUS window timer: it leaves the per-port
+ * table, bwcr and mapr alone, so no master is bandwidth limited.
+ */
+static void mctl_set_master_priority_b288(void)
+{
+ struct sunxi_mctl_com_reg * const mctl_com =
+ (struct sunxi_mctl_com_reg *)SUNXI_DRAM_COM_BASE;
+
+ clrsetbits_le32(&mctl_com->tmr, 0xfff, 399);
+}
+
static void mctl_set_master_priority(uint16_t socid)
{
switch (socid) {
+ case SOCID_B288:
+ mctl_set_master_priority_b288();
+ return;
case SOCID_H3:
mctl_set_master_priority_h3();
return;
@@ -430,14 +454,15 @@ static void mctl_sys_init(uint16_t socid, struct dram_para *para)
clrbits_le32(&ccm->ahb_gate0, 1 << AHB_GATE_OFFSET_MCTL);
clrbits_le32(&ccm->ahb_reset0_cfg, 1 << AHB_RESET_OFFSET_MCTL);
clrbits_le32(&ccm->pll5_cfg, CCM_PLL5_CTRL_EN);
- if (socid == SOCID_A64 || socid == SOCID_R40)
+ if (socid == SOCID_A64 || socid == SOCID_R40 || socid == SOCID_B288)
clrbits_le32(&ccm->pll11_cfg, CCM_PLL11_CTRL_EN);
udelay(10);
clrbits_le32(&ccm->dram_clk_cfg, CCM_DRAMCLK_CFG_RST);
udelay(1000);
- if (socid == SOCID_A64 || socid == SOCID_R40) {
+ if (socid == SOCID_A64 || socid == SOCID_R40 || socid == SOCID_B288) {
+ /* The B288 feeds the controller from PLL_DDR1 (pll11), too */
clock_set_pll11(CONFIG_DRAM_CLK * 2 * 1000000, false);
clrsetbits_le32(&ccm->dram_clk_cfg,
CCM_DRAMCLK_CFG_DIV_MASK |
@@ -464,7 +489,8 @@ static void mctl_sys_init(uint16_t socid, struct dram_para *para)
setbits_le32(&ccm->dram_clk_cfg, CCM_DRAMCLK_CFG_RST);
udelay(10);
- writel(socid == SOCID_H5 ? 0x8000 : 0xc00e, &mctl_ctl->clken);
+ writel((socid == SOCID_H5 || socid == SOCID_B288) ? 0x8000 : 0xc00e,
+ &mctl_ctl->clken);
udelay(500);
}
@@ -473,6 +499,14 @@ static void mctl_sys_init(uint16_t socid, struct dram_para *para)
#define DX_GCR_ODT_ALWAYS_ON (0x1 << 4)
#define DX_GCR_ODT_OFF (0x2 << 4)
+static void mctl_set_odtmap(struct dram_para *para)
+{
+ struct sunxi_mctl_ctl_reg * const mctl_ctl =
+ (struct sunxi_mctl_ctl_reg *)SUNXI_DRAM_CTL0_BASE;
+
+ writel(para->dual_rank ? 0x00000303 : 0x00000201, &mctl_ctl->odtmap);
+}
+
static int mctl_channel_init(uint16_t socid, struct dram_para *para)
{
struct sunxi_mctl_com_reg * const mctl_com =
@@ -488,7 +522,7 @@ static int mctl_channel_init(uint16_t socid, struct dram_para *para)
/* setting VTC, default disable all VT */
clrbits_le32(&mctl_ctl->pgcr[0], (1 << 30) | 0x3f);
- if (socid == SOCID_H5)
+ if (socid == SOCID_H5 || socid == SOCID_B288)
setbits_le32(&mctl_ctl->pgcr[1], (1 << 24) | (1 << 26));
else
clrsetbits_le32(&mctl_ctl->pgcr[1], 1 << 24, 1 << 26);
@@ -515,8 +549,9 @@ static int mctl_channel_init(uint16_t socid, struct dram_para *para)
}
/* AC PDR should always ON */
- clrsetbits_le32(&mctl_ctl->aciocr, socid == SOCID_H5 ? (0x1 << 11) : 0,
- 0x1 << 1);
+ clrsetbits_le32(&mctl_ctl->aciocr,
+ (socid == SOCID_H5 || socid == SOCID_B288) ?
+ (0x1 << 11) : 0, 0x1 << 1);
/* set DQS auto gating PD mode */
setbits_le32(&mctl_ctl->pgcr[2], 0x3 << 6);
@@ -535,7 +570,8 @@ static int mctl_channel_init(uint16_t socid, struct dram_para *para)
/* dphy & aphy phase select 270 degree */
clrsetbits_le32(&mctl_ctl->pgcr[2], (0x3 << 10) | (0x3 << 8),
(0x1 << 10) | (0x1 << 8));
- } else if (socid == SOCID_A64 || socid == SOCID_H5) {
+ } else if (socid == SOCID_A64 || socid == SOCID_H5 ||
+ socid == SOCID_B288) {
/* dphy & aphy phase select ? */
clrsetbits_le32(&mctl_ctl->pgcr[2], (0x3 << 10) | (0x3 << 8),
(0x0 << 10) | (0x3 << 8));
@@ -572,6 +608,19 @@ static int mctl_channel_init(uint16_t socid, struct dram_para *para)
mctl_phy_init(PIR_PLLINIT | PIR_DCAL | PIR_PHYRST |
PIR_DRAMRST | PIR_DRAMINIT | PIR_QSGATE);
+ } else if (socid == SOCID_B288) {
+ /* A 24-bit zqcr value, as on the A64; the H3 quirk hangs */
+ clrsetbits_le32(&mctl_ctl->zqcr, 0xffffff, CONFIG_DRAM_ZQ);
+ mctl_set_odtmap(para);
+
+ /* DQS gating mode 1: gate training finds the ranks and lanes */
+ clrbits_le32(&mctl_ctl->pgcr[2], 0x3 << 6);
+ clrbits_le32(&mctl_ctl->dqsgmr, 0x107);
+ /* the vendor's training configuration */
+ clrsetbits_le32(&mctl_ctl->dtcr, 0xffffff, 0x3087);
+ mctl_phy_init(PIR_ZCAL | PIR_PLLINIT | PIR_PHYRST);
+ mctl_phy_init(PIR_DCAL | PIR_DRAMRST | PIR_DRAMINIT |
+ PIR_QSGATE);
} else if (socid == SOCID_H3) {
mctl_h3_zq_calibration_quirk(para);
@@ -636,7 +685,7 @@ static int mctl_channel_init(uint16_t socid, struct dram_para *para)
udelay(10);
/* set PGCR3, CKE polarity */
- if (socid == SOCID_H3 || socid == SOCID_V3S)
+ if (socid == SOCID_H3 || socid == SOCID_V3S || socid == SOCID_B288)
writel(0x00aa0060, &mctl_ctl->pgcr[3]);
else if (socid == SOCID_A64 || socid == SOCID_H5 || socid == SOCID_R40)
writel(0xc0aa0060, &mctl_ctl->pgcr[3]);
@@ -822,6 +871,23 @@ static void mctl_auto_detect_dram_size(uint16_t socid, struct dram_para *para)
3, 3, 3, 3, 3, 3, 3, 3, \
3, 3, 3, 3, 2, 0, 0 }
+/* As programmed by the B288 boot0 */
+#define SUN8I_B288_DX_READ_DELAYS \
+ {{ 16, 17, 18, 19, 18, 19, 19, 19, 16, 0, 0 }, \
+ { 26, 26, 26, 25, 25, 25, 25, 25, 20, 0, 0 }, \
+ { 20, 22, 24, 22, 26, 25, 25, 25, 20, 0, 0 }, \
+ { 21, 21, 21, 20, 20, 19, 19, 19, 18, 0, 0 }}
+#define SUN8I_B288_DX_WRITE_DELAYS \
+ {{ 0, 1, 3, 3, 3, 3, 3, 4, 3, 11, 0 }, \
+ { 3, 3, 4, 4, 3, 3, 3, 3, 3, 11, 0 }, \
+ { 0, 3, 3, 1, 6, 6, 5, 6, 3, 9, 0 }, \
+ { 5, 5, 6, 6, 4, 5, 3, 3, 3, 9, 0 }}
+#define SUN8I_B288_AC_DELAYS \
+ { 0, 0, 8, 3, 0, 0, 0, 0, \
+ 0, 0, 0, 0, 0, 0, 0, 0, \
+ 0, 0, 0, 0, 0, 0, 0, 0, \
+ 0, 0, 0, 0, 3, 0, 0 }
+
unsigned long sunxi_dram_init(void)
{
struct sunxi_mctl_com_reg * const mctl_com =
@@ -851,6 +917,10 @@ unsigned long sunxi_dram_init(void)
.dx_read_delays = SUN8I_H3_DX_READ_DELAYS,
.dx_write_delays = SUN8I_H3_DX_WRITE_DELAYS,
.ac_delays = SUN8I_H3_AC_DELAYS,
+#elif defined(CONFIG_MACH_SUN8I_B288)
+ .dx_read_delays = SUN8I_B288_DX_READ_DELAYS,
+ .dx_write_delays = SUN8I_B288_DX_WRITE_DELAYS,
+ .ac_delays = SUN8I_B288_AC_DELAYS,
#elif defined(CONFIG_MACH_SUN8I_V3S)
.dx_read_delays = SUN8I_V3S_DX_READ_DELAYS,
.dx_write_delays = SUN8I_V3S_DX_WRITE_DELAYS,
@@ -878,6 +948,8 @@ unsigned long sunxi_dram_init(void)
uint16_t socid = SOCID_H3;
#elif defined(CONFIG_MACH_SUN8I_R40)
uint16_t socid = SOCID_R40;
+#elif defined(CONFIG_MACH_SUN8I_B288)
+ uint16_t socid = SOCID_B288;
#elif defined(CONFIG_MACH_SUN8I_V3S)
uint16_t socid = SOCID_V3S;
#elif defined(CONFIG_MACH_SUN50I)
@@ -890,12 +962,13 @@ unsigned long sunxi_dram_init(void)
if (mctl_channel_init(socid, ¶))
return 0;
- if (para.dual_rank)
- writel(0x00000303, &mctl_ctl->odtmap);
- else
- writel(0x00000201, &mctl_ctl->odtmap);
+ mctl_set_odtmap(¶);
udelay(1);
+ /* the B288 trains with static DX clocks; dynamic from now on */
+ if (socid == SOCID_B288)
+ clrbits_le32(&mctl_ctl->pgcr[0], (0x3 << 14) | (0x3 << 12));
+
/* odt delay */
if (socid == SOCID_H3)
writel(0x0c000400, &mctl_ctl->odtcfg);
--
2.52.0
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH 3/7] dt-bindings: clock: add the Allwinner B288 CCU
2026-10-16 9:16 [PATCH 0/7] sunxi: add the Allwinner B288 and the PocketBook Verse Pablo Mazzini
2026-10-16 9:16 ` [PATCH 1/7] sunxi: add support for the Allwinner B288 Pablo Mazzini
2026-10-16 9:16 ` [PATCH 2/7] sunxi: dram: support " Pablo Mazzini
@ 2026-10-16 9:16 ` Pablo Mazzini
2026-10-16 9:16 ` [PATCH 4/7] clk: sunxi: add the Allwinner B288 gates and resets Pablo Mazzini
` (4 subsequent siblings)
7 siblings, 0 replies; 10+ messages in thread
From: Pablo Mazzini @ 2026-10-16 9:16 UTC (permalink / raw)
To: Andre Przywara, u-boot; +Cc: Tom Rini, linux-sunxi
The clock and reset indices of the B288 CCU, as under review for Linux.
Signed-off-by: Pablo Mazzini <pmazzini@gmail.com>
---
include/dt-bindings/clock/sun8i-b288-ccu.h | 82 ++++++++++++++++++++++
include/dt-bindings/reset/sun8i-b288-ccu.h | 45 ++++++++++++
2 files changed, 127 insertions(+)
create mode 100644 include/dt-bindings/clock/sun8i-b288-ccu.h
create mode 100644 include/dt-bindings/reset/sun8i-b288-ccu.h
diff --git a/include/dt-bindings/clock/sun8i-b288-ccu.h b/include/dt-bindings/clock/sun8i-b288-ccu.h
new file mode 100644
index 00000000000..c9b9eaf979a
--- /dev/null
+++ b/include/dt-bindings/clock/sun8i-b288-ccu.h
@@ -0,0 +1,82 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR MIT) */
+#ifndef _DT_BINDINGS_CLK_SUN8I_B288_H_
+#define _DT_BINDINGS_CLK_SUN8I_B288_H_
+
+#define CLK_PLL_CPUX 0
+#define CLK_PLL_AUDIO_BASE 1
+#define CLK_PLL_VIDEO0 2
+#define CLK_PLL_DDR0 3
+#define CLK_PLL_PERIPH0 4
+#define CLK_PLL_VIDEO1 5
+#define CLK_PLL_24M 6
+#define CLK_PLL_PERIPH1 7
+#define CLK_PLL_DE 8
+#define CLK_PLL_DDR1 9
+
+#define CLK_PLL_PERIPH0_2X 10
+#define CLK_PLL_PERIPH1_2X 11
+#define CLK_CPUX 12
+#define CLK_AXI 13
+#define CLK_CPUAPB 14
+#define CLK_AHB1 15
+#define CLK_APB1 16
+#define CLK_APB2 17
+
+#define CLK_NAND 18
+#define CLK_MMC0 19
+#define CLK_MMC1 20
+#define CLK_MMC2 21
+#define CLK_MMC3 22
+#define CLK_SPI0 23
+#define CLK_SPI1 24
+#define CLK_SPI2 25
+#define CLK_DRAM 26
+#define CLK_DE 27
+#define CLK_EE 28
+#define CLK_EDMA 29
+#define CLK_TCON0 30
+#define CLK_MBUS 31
+
+#define CLK_BUS_THS 32
+#define CLK_BUS_NAND 33
+#define CLK_BUS_SDMMC0_BUS 34
+#define CLK_BUS_SDMMC1_BUS 35
+#define CLK_BUS_SDMMC2_BUS 36
+#define CLK_BUS_SDMMC3_BUS 37
+#define CLK_BUS_SPI0 38
+#define CLK_BUS_SPI1 39
+#define CLK_BUS_SPI2 40
+#define CLK_BUS_I2S0 41
+#define CLK_BUS_I2S1 42
+#define CLK_BUS_SPDIF 43
+#define CLK_BUS_DSD 44
+#define CLK_BUS_DMIC 45
+#define CLK_BUS_USBOHCI0 46
+#define CLK_BUS_USBEHCI0 47
+#define CLK_BUS_USBOTG 48
+#define CLK_BUS_DE 49
+#define CLK_BUS_EE 50
+#define CLK_BUS_TCON0 51
+#define CLK_BUS_CSI 52
+#define CLK_BUS_ADDA 53
+#define CLK_BUS_SDRAM 54
+#define CLK_BUS_PSRAM 55
+#define CLK_BUS_DMA 56
+#define CLK_BUS_UART0 57
+#define CLK_BUS_UART1 58
+#define CLK_BUS_UART2 59
+#define CLK_BUS_UART3 60
+#define CLK_BUS_UART4 61
+#define CLK_BUS_UART5 62
+#define CLK_BUS_TWI0 63
+#define CLK_BUS_TWI1 64
+#define CLK_BUS_TWI2 65
+#define CLK_BUS_PIO 66
+#define CLK_BUS_GPADC 67
+#define CLK_BUS_KEYADC 68
+#define CLK_MMC0_SAMPLE 69
+#define CLK_MMC0_OUTPUT 70
+#define CLK_MMC1_SAMPLE 71
+#define CLK_MMC1_OUTPUT 72
+
+#endif
diff --git a/include/dt-bindings/reset/sun8i-b288-ccu.h b/include/dt-bindings/reset/sun8i-b288-ccu.h
new file mode 100644
index 00000000000..67514565454
--- /dev/null
+++ b/include/dt-bindings/reset/sun8i-b288-ccu.h
@@ -0,0 +1,45 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR MIT) */
+#ifndef _DT_BINDINGS_RST_SUN8I_B288_H_
+#define _DT_BINDINGS_RST_SUN8I_B288_H_
+
+#define RST_BUS_THS 0
+#define RST_BUS_NAND 1
+#define RST_BUS_MMC0 2
+#define RST_BUS_MMC1 3
+#define RST_BUS_MMC2 4
+#define RST_BUS_MMC3 5
+#define RST_BUS_SPI0 6
+#define RST_BUS_SPI1 7
+#define RST_BUS_SPI2 8
+#define RST_BUS_I2S0 9
+#define RST_BUS_I2S1 10
+#define RST_BUS_SPDIF 11
+#define RST_BUS_DSD 12
+#define RST_BUS_DMIC 13
+#define RST_USBPHY0 14
+#define RST_BUS_OHCI0 15
+#define RST_BUS_EHCI0 16
+#define RST_BUS_OTG 17
+#define RST_BUS_DE 18
+#define RST_BUS_EE 19
+#define RST_BUS_TCON0 20
+#define RST_BUS_CSI 21
+#define RST_BUS_ADDA 22
+#define RST_BUS_WLAN 23
+#define RST_MBUS 24
+#define RST_BUS_DRAM 25
+#define RST_BUS_PSRAM 26
+#define RST_BUS_DMA 27
+#define RST_BUS_UART0 28
+#define RST_BUS_UART1 29
+#define RST_BUS_UART2 30
+#define RST_BUS_UART3 31
+#define RST_BUS_UART4 32
+#define RST_BUS_UART5 33
+#define RST_BUS_I2C0 34
+#define RST_BUS_I2C1 35
+#define RST_BUS_I2C2 36
+#define RST_BUS_GPADC 37
+#define RST_BUS_KEYADC 38
+
+#endif
--
2.52.0
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH 4/7] clk: sunxi: add the Allwinner B288 gates and resets
2026-10-16 9:16 [PATCH 0/7] sunxi: add the Allwinner B288 and the PocketBook Verse Pablo Mazzini
` (2 preceding siblings ...)
2026-10-16 9:16 ` [PATCH 3/7] dt-bindings: clock: add the Allwinner B288 CCU Pablo Mazzini
@ 2026-10-16 9:16 ` Pablo Mazzini
2026-10-16 9:16 ` [PATCH 5/7] pinctrl: sunxi: add the Allwinner B288 PIO Pablo Mazzini
` (3 subsequent siblings)
7 siblings, 0 replies; 10+ messages in thread
From: Pablo Mazzini @ 2026-10-16 9:16 UTC (permalink / raw)
To: Andre Przywara, u-boot; +Cc: Tom Rini, linux-sunxi, Lukasz Majewski
The bus clock gates and resets, as in the Linux CCU driver.
Signed-off-by: Pablo Mazzini <pmazzini@gmail.com>
---
drivers/clk/sunxi/Kconfig | 7 +++
drivers/clk/sunxi/Makefile | 1 +
drivers/clk/sunxi/clk_b288.c | 101 ++++++++++++++++++++++++++++++++++
drivers/clk/sunxi/clk_sunxi.c | 5 ++
4 files changed, 114 insertions(+)
create mode 100644 drivers/clk/sunxi/clk_b288.c
diff --git a/drivers/clk/sunxi/Kconfig b/drivers/clk/sunxi/Kconfig
index 1c1cc82719c..e4fe6f63626 100644
--- a/drivers/clk/sunxi/Kconfig
+++ b/drivers/clk/sunxi/Kconfig
@@ -52,6 +52,13 @@ config CLK_SUN8I_A23
This enables common clock driver support for platforms based
on Allwinner A23/A33 SoC.
+config CLK_SUN8I_B288
+ bool "Clock driver for Allwinner B288"
+ default MACH_SUN8I_B288
+ help
+ This enables common clock driver support for platforms based
+ on Allwinner B288 SoC.
+
config CLK_SUN8I_A83T
bool "Clock driver for Allwinner A83T"
default MACH_SUN8I_A83T
diff --git a/drivers/clk/sunxi/Makefile b/drivers/clk/sunxi/Makefile
index 93b542cebcd..4f278ff551a 100644
--- a/drivers/clk/sunxi/Makefile
+++ b/drivers/clk/sunxi/Makefile
@@ -15,6 +15,7 @@ obj-$(CONFIG_CLK_SUN6I_A31) += clk_a31.o
obj-$(CONFIG_CLK_SUN6I_A31_R) += clk_a31_r.o
obj-$(CONFIG_CLK_SUN8I_A23) += clk_a23.o
obj-$(CONFIG_CLK_SUN8I_A83T) += clk_a83t.o
+obj-$(CONFIG_CLK_SUN8I_B288) += clk_b288.o
obj-$(CONFIG_CLK_SUN8I_R40) += clk_r40.o
obj-$(CONFIG_CLK_SUN8I_V3S) += clk_v3s.o
obj-$(CONFIG_CLK_SUN9I_A80) += clk_a80.o
diff --git a/drivers/clk/sunxi/clk_b288.c b/drivers/clk/sunxi/clk_b288.c
new file mode 100644
index 00000000000..505fa27f83a
--- /dev/null
+++ b/drivers/clk/sunxi/clk_b288.c
@@ -0,0 +1,101 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Allwinner B288 (sun8iw10p1) CCU gates and resets
+ */
+
+#include <clk-uclass.h>
+#include <dm.h>
+#include <errno.h>
+#include <clk/sunxi.h>
+#include <dt-bindings/clock/sun8i-b288-ccu.h>
+#include <dt-bindings/reset/sun8i-b288-ccu.h>
+#include <linux/bitops.h>
+
+static const struct ccu_clk_gate b288_gates[] = {
+ [CLK_BUS_DMA] = GATE(0x060, BIT(6)),
+ [CLK_BUS_SDMMC0_BUS] = GATE(0x060, BIT(8)),
+ [CLK_BUS_SDMMC1_BUS] = GATE(0x060, BIT(9)),
+ [CLK_BUS_SDMMC2_BUS] = GATE(0x060, BIT(10)),
+ [CLK_BUS_SDMMC3_BUS] = GATE(0x060, BIT(11)),
+ [CLK_BUS_NAND] = GATE(0x060, BIT(13)),
+ [CLK_BUS_SDRAM] = GATE(0x060, BIT(14)),
+ [CLK_BUS_PSRAM] = GATE(0x060, BIT(15)),
+ [CLK_BUS_SPI0] = GATE(0x060, BIT(20)),
+ [CLK_BUS_SPI1] = GATE(0x060, BIT(21)),
+ [CLK_BUS_SPI2] = GATE(0x060, BIT(22)),
+ [CLK_BUS_USBOTG] = GATE(0x060, BIT(24)),
+ [CLK_BUS_USBEHCI0] = GATE(0x060, BIT(26)),
+ [CLK_BUS_USBOHCI0] = GATE(0x060, BIT(29)),
+ [CLK_BUS_TCON0] = GATE(0x064, BIT(4)),
+ [CLK_BUS_CSI] = GATE(0x064, BIT(8)),
+ [CLK_BUS_DE] = GATE(0x064, BIT(12)),
+ [CLK_BUS_EE] = GATE(0x064, BIT(13)),
+ [CLK_BUS_ADDA] = GATE(0x068, BIT(0)),
+ [CLK_BUS_SPDIF] = GATE(0x068, BIT(1)),
+ [CLK_BUS_DSD] = GATE(0x068, BIT(2)),
+ [CLK_BUS_DMIC] = GATE(0x068, BIT(3)),
+ [CLK_BUS_PIO] = GATE(0x068, BIT(5)),
+ [CLK_BUS_THS] = GATE(0x068, BIT(8)),
+ [CLK_BUS_KEYADC] = GATE(0x068, BIT(9)),
+ [CLK_BUS_GPADC] = GATE(0x068, BIT(10)),
+ [CLK_BUS_I2S0] = GATE(0x068, BIT(12)),
+ [CLK_BUS_I2S1] = GATE(0x068, BIT(13)),
+ [CLK_BUS_TWI0] = GATE(0x06c, BIT(0)),
+ [CLK_BUS_TWI1] = GATE(0x06c, BIT(1)),
+ [CLK_BUS_TWI2] = GATE(0x06c, BIT(2)),
+ [CLK_BUS_UART0] = GATE(0x06c, BIT(16)),
+ [CLK_BUS_UART1] = GATE(0x06c, BIT(17)),
+ [CLK_BUS_UART2] = GATE(0x06c, BIT(18)),
+ [CLK_BUS_UART3] = GATE(0x06c, BIT(19)),
+ [CLK_BUS_UART4] = GATE(0x06c, BIT(20)),
+ [CLK_BUS_UART5] = GATE(0x06c, BIT(21)),
+};
+
+static const struct ccu_reset b288_resets[] = {
+ [RST_USBPHY0] = RESET(0x0cc, BIT(0)),
+ [RST_MBUS] = RESET(0x0fc, BIT(31)),
+ [RST_BUS_DMA] = RESET(0x2c0, BIT(6)),
+ [RST_BUS_MMC0] = RESET(0x2c0, BIT(8)),
+ [RST_BUS_MMC1] = RESET(0x2c0, BIT(9)),
+ [RST_BUS_MMC2] = RESET(0x2c0, BIT(10)),
+ [RST_BUS_MMC3] = RESET(0x2c0, BIT(11)),
+ [RST_BUS_NAND] = RESET(0x2c0, BIT(13)),
+ [RST_BUS_DRAM] = RESET(0x2c0, BIT(14)),
+ [RST_BUS_PSRAM] = RESET(0x2c0, BIT(15)),
+ [RST_BUS_SPI0] = RESET(0x2c0, BIT(20)),
+ [RST_BUS_SPI1] = RESET(0x2c0, BIT(21)),
+ [RST_BUS_SPI2] = RESET(0x2c0, BIT(22)),
+ [RST_BUS_OTG] = RESET(0x2c0, BIT(24)),
+ [RST_BUS_EHCI0] = RESET(0x2c0, BIT(26)),
+ [RST_BUS_OHCI0] = RESET(0x2c0, BIT(29)),
+ [RST_BUS_WLAN] = RESET(0x2c4, BIT(1)),
+ [RST_BUS_TCON0] = RESET(0x2c4, BIT(4)),
+ [RST_BUS_CSI] = RESET(0x2c4, BIT(8)),
+ [RST_BUS_DE] = RESET(0x2c4, BIT(12)),
+ [RST_BUS_EE] = RESET(0x2c4, BIT(13)),
+ [RST_BUS_ADDA] = RESET(0x2d0, BIT(0)),
+ [RST_BUS_SPDIF] = RESET(0x2d0, BIT(1)),
+ [RST_BUS_DSD] = RESET(0x2d0, BIT(2)),
+ [RST_BUS_DMIC] = RESET(0x2d0, BIT(3)),
+ [RST_BUS_THS] = RESET(0x2d0, BIT(8)),
+ [RST_BUS_KEYADC] = RESET(0x2d0, BIT(9)),
+ [RST_BUS_GPADC] = RESET(0x2d0, BIT(10)),
+ [RST_BUS_I2S0] = RESET(0x2d0, BIT(12)),
+ [RST_BUS_I2S1] = RESET(0x2d0, BIT(13)),
+ [RST_BUS_I2C0] = RESET(0x2d8, BIT(0)),
+ [RST_BUS_I2C1] = RESET(0x2d8, BIT(1)),
+ [RST_BUS_I2C2] = RESET(0x2d8, BIT(2)),
+ [RST_BUS_UART0] = RESET(0x2d8, BIT(16)),
+ [RST_BUS_UART1] = RESET(0x2d8, BIT(17)),
+ [RST_BUS_UART2] = RESET(0x2d8, BIT(18)),
+ [RST_BUS_UART3] = RESET(0x2d8, BIT(19)),
+ [RST_BUS_UART4] = RESET(0x2d8, BIT(20)),
+ [RST_BUS_UART5] = RESET(0x2d8, BIT(21)),
+};
+
+const struct ccu_desc b288_ccu_desc = {
+ .gates = b288_gates,
+ .resets = b288_resets,
+ .num_gates = ARRAY_SIZE(b288_gates),
+ .num_resets = ARRAY_SIZE(b288_resets),
+};
diff --git a/drivers/clk/sunxi/clk_sunxi.c b/drivers/clk/sunxi/clk_sunxi.c
index 046d5d1605a..5f40f30fe89 100644
--- a/drivers/clk/sunxi/clk_sunxi.c
+++ b/drivers/clk/sunxi/clk_sunxi.c
@@ -117,6 +117,7 @@ extern const struct ccu_desc a64_ccu_desc;
extern const struct ccu_desc a80_ccu_desc;
extern const struct ccu_desc a80_mmc_clk_desc;
extern const struct ccu_desc a83t_ccu_desc;
+extern const struct ccu_desc b288_ccu_desc;
extern const struct ccu_desc d1_ccu_desc;
extern const struct ccu_desc f1c100s_ccu_desc;
extern const struct ccu_desc h3_ccu_desc;
@@ -154,6 +155,10 @@ static const struct udevice_id sunxi_clk_ids[] = {
{ .compatible = "allwinner,sun8i-a33-ccu",
.data = (ulong)&a23_ccu_desc },
#endif
+#ifdef CONFIG_CLK_SUN8I_B288
+ { .compatible = "allwinner,sun8i-b288-ccu",
+ .data = (ulong)&b288_ccu_desc },
+#endif
#ifdef CONFIG_CLK_SUN8I_A83T
{ .compatible = "allwinner,sun8i-a83t-ccu",
.data = (ulong)&a83t_ccu_desc },
--
2.52.0
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH 5/7] pinctrl: sunxi: add the Allwinner B288 PIO
2026-10-16 9:16 [PATCH 0/7] sunxi: add the Allwinner B288 and the PocketBook Verse Pablo Mazzini
` (3 preceding siblings ...)
2026-10-16 9:16 ` [PATCH 4/7] clk: sunxi: add the Allwinner B288 gates and resets Pablo Mazzini
@ 2026-10-16 9:16 ` Pablo Mazzini
2026-10-16 9:16 ` [PATCH 6/7] mmc: sunxi: B288 mmc0/mmc1 run off PLL_PERIPH0 2x Pablo Mazzini
` (2 subsequent siblings)
7 siblings, 0 replies; 10+ messages in thread
From: Pablo Mazzini @ 2026-10-16 9:16 UTC (permalink / raw)
To: Andre Przywara, u-boot; +Cc: Tom Rini, linux-sunxi
The pin functions used by the PocketBook Verse.
Signed-off-by: Pablo Mazzini <pmazzini@gmail.com>
---
drivers/pinctrl/sunxi/Kconfig | 5 +++++
drivers/pinctrl/sunxi/pinctrl-sunxi.c | 22 ++++++++++++++++++++++
2 files changed, 27 insertions(+)
diff --git a/drivers/pinctrl/sunxi/Kconfig b/drivers/pinctrl/sunxi/Kconfig
index 54314992299..748a4140fbd 100644
--- a/drivers/pinctrl/sunxi/Kconfig
+++ b/drivers/pinctrl/sunxi/Kconfig
@@ -54,6 +54,11 @@ config PINCTRL_SUN8I_A33
default MACH_SUN8I_A33
select PINCTRL_SUNXI
+config PINCTRL_SUN8I_B288
+ bool "Support for the Allwinner B288 PIO"
+ default MACH_SUN8I_B288
+ select PINCTRL_SUNXI
+
config PINCTRL_SUN8I_A83T
bool "Support for the Allwinner A83T PIO"
default MACH_SUN8I_A83T
diff --git a/drivers/pinctrl/sunxi/pinctrl-sunxi.c b/drivers/pinctrl/sunxi/pinctrl-sunxi.c
index ab4e88c9918..29219c11b93 100644
--- a/drivers/pinctrl/sunxi/pinctrl-sunxi.c
+++ b/drivers/pinctrl/sunxi/pinctrl-sunxi.c
@@ -448,6 +448,22 @@ static const struct sunxi_pinctrl_desc __maybe_unused sun8i_a33_pinctrl_desc = {
.num_banks = 8,
};
+static const struct sunxi_pinctrl_function sun8i_b288_pinctrl_functions[] = {
+ { "gpio_in", 0 },
+ { "gpio_out", 1 },
+ { "i2c0", 2 }, /* PB6-PB7 */
+ { "mmc0", 2 }, /* PF0-PF5 */
+ { "mmc3", 5 }, /* PC1, PC4-PC14 */
+ { "uart0", 2 }, /* PB4-PB5 */
+};
+
+static const struct sunxi_pinctrl_desc __maybe_unused sun8i_b288_pinctrl_desc = {
+ .functions = sun8i_b288_pinctrl_functions,
+ .num_functions = ARRAY_SIZE(sun8i_b288_pinctrl_functions),
+ .first_bank = SUNXI_GPIO_A,
+ .num_banks = 7,
+};
+
static const struct sunxi_pinctrl_function sun8i_a83t_pinctrl_functions[] = {
{ "gmac", 4 }, /* PD2-PD23 */
{ "gpio_in", 0 },
@@ -912,6 +928,12 @@ static const struct udevice_id sunxi_pinctrl_ids[] = {
.data = (ulong)&sun8i_a33_pinctrl_desc,
},
#endif
+#ifdef CONFIG_PINCTRL_SUN8I_B288
+ {
+ .compatible = "allwinner,sun8i-b288-pinctrl",
+ .data = (ulong)&sun8i_b288_pinctrl_desc,
+ },
+#endif
#ifdef CONFIG_PINCTRL_SUN8I_A83T
{
.compatible = "allwinner,sun8i-a83t-pinctrl",
--
2.52.0
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH 6/7] mmc: sunxi: B288 mmc0/mmc1 run off PLL_PERIPH0 2x
2026-10-16 9:16 [PATCH 0/7] sunxi: add the Allwinner B288 and the PocketBook Verse Pablo Mazzini
` (4 preceding siblings ...)
2026-10-16 9:16 ` [PATCH 5/7] pinctrl: sunxi: add the Allwinner B288 PIO Pablo Mazzini
@ 2026-10-16 9:16 ` Pablo Mazzini
2026-10-16 9:16 ` [PATCH 7/7] sunxi: add the PocketBook Verse Pablo Mazzini
2026-10-16 17:28 ` [PATCH 0/7] sunxi: add the Allwinner B288 and " Andre Przywara
7 siblings, 0 replies; 10+ messages in thread
From: Pablo Mazzini @ 2026-10-16 9:16 UTC (permalink / raw)
To: Andre Przywara, u-boot
Cc: Tom Rini, linux-sunxi, Peng Fan, Tanmay Kathpalia, Jaehoon Chung
Their mux input 1 is PLL_PERIPH0 2x, and unlike mmc2/mmc3 they do not
halve it.
Signed-off-by: Pablo Mazzini <pmazzini@gmail.com>
---
drivers/mmc/sunxi_mmc.c | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/drivers/mmc/sunxi_mmc.c b/drivers/mmc/sunxi_mmc.c
index 84f4e4c2198..7329ca3e24e 100644
--- a/drivers/mmc/sunxi_mmc.c
+++ b/drivers/mmc/sunxi_mmc.c
@@ -100,6 +100,13 @@ static int mmc_set_mod_clk(struct sunxi_mmc_priv *priv, unsigned int hz)
if (IS_ENABLED(CONFIG_MACH_SUN8I_R528))
pll_hz /= 2;
+ /*
+ * The B288's mux input 1 is PLL_PERIPH0 2x, and only the
+ * mmc2/mmc3 controllers halve it.
+ */
+ if (IS_ENABLED(CONFIG_MACH_SUN8I_B288) && priv->mmc_no < 2)
+ pll_hz *= 2;
+
/*
* The A523/T527 uses PERIPH0_400M as the MMC0/1 input clock,
* and PERIPH0_800M for MMC2. There is also the hidden divider
--
2.52.0
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH 7/7] sunxi: add the PocketBook Verse
2026-10-16 9:16 [PATCH 0/7] sunxi: add the Allwinner B288 and the PocketBook Verse Pablo Mazzini
` (5 preceding siblings ...)
2026-10-16 9:16 ` [PATCH 6/7] mmc: sunxi: B288 mmc0/mmc1 run off PLL_PERIPH0 2x Pablo Mazzini
@ 2026-10-16 9:16 ` Pablo Mazzini
2026-10-16 17:28 ` [PATCH 0/7] sunxi: add the Allwinner B288 and " Andre Przywara
7 siblings, 0 replies; 10+ messages in thread
From: Pablo Mazzini @ 2026-10-16 9:16 UTC (permalink / raw)
To: Andre Przywara, u-boot; +Cc: Tom Rini, linux-sunxi, Ilias Apalodimas
An Allwinner B288 e-reader. The DT is a copy of the one under review for
Linux, until it can come from dts/upstream.
Signed-off-by: Pablo Mazzini <pmazzini@gmail.com>
---
arch/arm/dts/Makefile | 2 +
arch/arm/dts/sun8i-b288-pocketbook-verse.dts | 114 ++++++++
arch/arm/dts/sun8i-b288.dtsi | 292 +++++++++++++++++++
board/sunxi/MAINTAINERS | 6 +
configs/pocketbook_verse_defconfig | 10 +
5 files changed, 424 insertions(+)
create mode 100644 arch/arm/dts/sun8i-b288-pocketbook-verse.dts
create mode 100644 arch/arm/dts/sun8i-b288.dtsi
create mode 100644 configs/pocketbook_verse_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 099e3f082b6..039fbab2a90 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -586,6 +586,8 @@ dtb-$(CONFIG_MACH_SUN8I_A83T) += \
sun8i-a83t-bananapi-m3.dtb \
sun8i-a83t-cubietruck-plus.dtb \
sun8i-a83t-tbs-a711.dtb
+dtb-$(CONFIG_MACH_SUN8I_B288) += \
+ sun8i-b288-pocketbook-verse.dtb
dtb-$(CONFIG_MACH_SUN8I_H3) += \
sun8i-h2-plus-bananapi-m2-zero.dtb \
sun8i-h2-plus-libretech-all-h3-cc.dtb \
diff --git a/arch/arm/dts/sun8i-b288-pocketbook-verse.dts b/arch/arm/dts/sun8i-b288-pocketbook-verse.dts
new file mode 100644
index 00000000000..a60cbb63801
--- /dev/null
+++ b/arch/arm/dts/sun8i-b288-pocketbook-verse.dts
@@ -0,0 +1,114 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * PocketBook Verse (PB629), an Allwinner B288 based e-reader.
+ */
+
+/dts-v1/;
+#include "sun8i-b288.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "PocketBook Verse";
+ compatible = "pocketbook,verse", "allwinner,sun8i-b288";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pb_pins>;
+ status = "okay";
+};
+
+&mmc0 {
+ vmmc-supply = <®_dldo2>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ disable-wp;
+ status = "okay";
+};
+
+&mmc3 {
+ vmmc-supply = <®_dcdc1>;
+ vqmmc-supply = <®_dldo1>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ status = "okay";
+};
+
+&pio {
+ vcc-pc-supply = <®_dldo1>;
+ vcc-pd-supply = <®_dldo1>;
+};
+
+&i2c0 {
+ status = "okay";
+
+ axp22x: pmic@34 {
+ /* labelled AXP227 */
+ compatible = "x-powers,axp221";
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+#include "axp22x.dtsi"
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-io";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1260000>;
+ regulator-max-microvolt = <1260000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc4 {
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-sys";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-name = "vcc-dram";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_dldo1 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-pc";
+};
+
+®_dldo2 {
+ /* microSD slot */
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-sdcv";
+};
diff --git a/arch/arm/dts/sun8i-b288.dtsi b/arch/arm/dts/sun8i-b288.dtsi
new file mode 100644
index 00000000000..53832ea9dc0
--- /dev/null
+++ b/arch/arm/dts/sun8i-b288.dtsi
@@ -0,0 +1,292 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Allwinner B288 (sun8iw10p1) SoC
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/sun6i-rtc.h>
+#include <dt-bindings/clock/sun8i-b288-ccu.h>
+#include <dt-bindings/reset/sun8i-b288-ccu.h>
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ interrupt-parent = <&gic>;
+
+ osc24M: osc24M-clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ clock-output-names = "osc24M";
+ };
+
+ osc32k: osc32k-clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ clock-output-names = "ext-osc32k";
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <0>;
+ clocks = <&ccu CLK_CPUX>;
+ clock-names = "cpu";
+ };
+
+ cpu1: cpu@1 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <1>;
+ clocks = <&ccu CLK_CPUX>;
+ clock-names = "cpu";
+ };
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ nmi_intc: interrupt-controller@1c000d0 {
+ compatible = "allwinner,sun8i-b288-nmi",
+ "allwinner,sun9i-a80-nmi";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x01c000d0 0x0c>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ /*
+ * mmc0 is a v4p1x controller, so it runs in the old timing
+ * mode and needs the sample and output phase clocks.
+ */
+ mmc0: mmc@1c0f000 {
+ compatible = "allwinner,sun8i-b288-mmc",
+ "allwinner,sun7i-a20-mmc";
+ reg = <0x01c0f000 0x1000>;
+ clocks = <&ccu CLK_BUS_SDMMC0_BUS>,
+ <&ccu CLK_MMC0>,
+ <&ccu CLK_MMC0_OUTPUT>,
+ <&ccu CLK_MMC0_SAMPLE>;
+ clock-names = "ahb", "mmc", "output", "sample";
+ resets = <&ccu RST_BUS_MMC0>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc3: mmc@1c12000 {
+ compatible = "allwinner,sun8i-b288-emmc",
+ "allwinner,sun50i-a64-emmc";
+ reg = <0x01c12000 0x1000>;
+ clocks = <&ccu CLK_BUS_SDMMC3_BUS>, <&ccu CLK_MMC3>;
+ clock-names = "ahb", "mmc";
+ resets = <&ccu RST_BUS_MMC3>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc3_pins>;
+ max-frequency = <150000000>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ /* mmc2 @0x01c11000 is an unsupported SDHCI-style controller. */
+
+ ccu: clock-controller@1c20000 {
+ compatible = "allwinner,sun8i-b288-ccu";
+ reg = <0x01c20000 0x400>;
+ clocks = <&osc24M>, <&rtc CLK_OSC32K>;
+ clock-names = "hosc", "losc";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ rtc: rtc@1c20400 {
+ compatible = "allwinner,sun8i-b288-rtc";
+ reg = <0x01c20400 0x400>;
+ interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+ clock-output-names = "osc32k", "osc32k-out";
+ clocks = <&osc32k>;
+ #clock-cells = <1>;
+ };
+
+ pio: pinctrl@1c20800 {
+ compatible = "allwinner,sun8i-b288-pinctrl";
+ reg = <0x01c20800 0x400>;
+ interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&rtc CLK_OSC32K>;
+ clock-names = "apb", "hosc", "losc";
+ gpio-controller;
+ #gpio-cells = <3>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+
+ mmc0_pins: mmc0-pins {
+ pins = "PF0", "PF1", "PF2",
+ "PF3", "PF4", "PF5";
+ function = "mmc0";
+ allwinner,pinmux = <2>;
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ i2c0_pins: i2c0-pins {
+ pins = "PB6", "PB7";
+ function = "i2c0";
+ allwinner,pinmux = <2>;
+ };
+
+ mmc3_pins: mmc3-pins {
+ pins = "PC1", "PC4", "PC5", "PC6",
+ "PC7", "PC8", "PC9", "PC10",
+ "PC11", "PC12", "PC13", "PC14";
+ function = "mmc3";
+ allwinner,pinmux = <5>;
+ drive-strength = <40>;
+ bias-pull-up;
+ };
+
+ uart0_pb_pins: uart0-pb-pins {
+ pins = "PB4", "PB5";
+ function = "uart0";
+ allwinner,pinmux = <2>;
+ };
+ };
+
+ wdt: watchdog@1c20ca0 {
+ compatible = "allwinner,sun8i-b288-wdt",
+ "allwinner,sun6i-a31-wdt";
+ reg = <0x01c20ca0 0x20>;
+ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&osc24M>;
+ };
+
+ uart0: serial@1c28000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28000 0x400>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART0>;
+ resets = <&ccu RST_BUS_UART0>;
+ status = "disabled";
+ };
+
+ uart1: serial@1c28400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28400 0x400>;
+ interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART1>;
+ resets = <&ccu RST_BUS_UART1>;
+ status = "disabled";
+ };
+
+ uart2: serial@1c28800 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28800 0x400>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART2>;
+ resets = <&ccu RST_BUS_UART2>;
+ status = "disabled";
+ };
+
+ uart3: serial@1c28c00 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28c00 0x400>;
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART3>;
+ resets = <&ccu RST_BUS_UART3>;
+ status = "disabled";
+ };
+
+ uart4: serial@1c29000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c29000 0x400>;
+ interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART4>;
+ resets = <&ccu RST_BUS_UART4>;
+ status = "disabled";
+ };
+
+ i2c0: i2c@1c2ac00 {
+ compatible = "allwinner,sun8i-b288-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2ac00 0x400>;
+ interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_TWI0>;
+ resets = <&ccu RST_BUS_I2C0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c1: i2c@1c2b000 {
+ compatible = "allwinner,sun8i-b288-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2b000 0x400>;
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_TWI1>;
+ resets = <&ccu RST_BUS_I2C1>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c2: i2c@1c2b400 {
+ compatible = "allwinner,sun8i-b288-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2b400 0x400>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_TWI2>;
+ resets = <&ccu RST_BUS_I2C2>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ gic: interrupt-controller@1c81000 {
+ compatible = "arm,gic-400";
+ reg = <0x01c81000 0x1000>,
+ <0x01c82000 0x2000>,
+ <0x01c84000 0x2000>,
+ <0x01c86000 0x2000>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ };
+ };
+};
diff --git a/board/sunxi/MAINTAINERS b/board/sunxi/MAINTAINERS
index df745f14649..53fd2666f21 100644
--- a/board/sunxi/MAINTAINERS
+++ b/board/sunxi/MAINTAINERS
@@ -539,6 +539,12 @@ M: Arnaud Ferraris <arnaud.ferraris@collabora.com>
S: Maintained
F: configs/pinetab_defconfig
+POCKETBOOK VERSE BOARD
+M: Pablo Mazzini <pmazzini@gmail.com>
+S: Maintained
+F: arch/arm/dts/sun8i-b288*
+F: configs/pocketbook_verse_defconfig
+
R16 EVB PARROT BOARD
M: Quentin Schulz <quentin.schulz@free-electrons.com>
S: Maintained
diff --git a/configs/pocketbook_verse_defconfig b/configs/pocketbook_verse_defconfig
new file mode 100644
index 00000000000..df86ab4b786
--- /dev/null
+++ b/configs/pocketbook_verse_defconfig
@@ -0,0 +1,10 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_DEFAULT_DEVICE_TREE="sun8i-b288-pocketbook-verse"
+CONFIG_DRAM_CLK=672
+CONFIG_SPL=y
+CONFIG_MACH_SUN8I_B288=y
+CONFIG_DRAM_ZQ=3881977
+# CONFIG_HAS_ARMV7_SECURE_BASE is not set
+# CONFIG_OF_UPSTREAM is not set
+CONFIG_NO_NET=y
--
2.52.0
^ permalink raw reply related [flat|nested] 10+ messages in thread* Re: [PATCH 0/7] sunxi: add the Allwinner B288 and the PocketBook Verse
2026-10-16 9:16 [PATCH 0/7] sunxi: add the Allwinner B288 and the PocketBook Verse Pablo Mazzini
` (6 preceding siblings ...)
2026-10-16 9:16 ` [PATCH 7/7] sunxi: add the PocketBook Verse Pablo Mazzini
@ 2026-10-16 17:28 ` Andre Przywara
2026-10-16 18:38 ` Pablo Mazzini
7 siblings, 1 reply; 10+ messages in thread
From: Andre Przywara @ 2026-10-16 17:28 UTC (permalink / raw)
To: Pablo Mazzini, u-boot; +Cc: Tom Rini, linux-sunxi
Hi Pablo,
On 10/16/26 11:16, Pablo Mazzini wrote:
> The Allwinner B288 (sun8iw10p1) is a dual Cortex-A7 SoC used in e-book
> readers. This series adds SPL and U-Boot support for it, and one board:
> the PocketBook Verse (PB629).
> > The DT is still under review for Linux. Until it reaches
> dts/upstream, the last patch carries a copy in arch/arm/dts.
Thanks for sending this, much appreciated. I had a coarse look over
this, and this looks fine on the first glance.
As you said, this is somewhat blocked on the DT merge on the Linux side,
which will probably not happen this year anymore (v7.5-rc1 would be the
earliest).
But meanwhile, in preparation for that, could you please reorder the
patches, so you enable the devices first (clocks, pinctrl, mmc), then
DRAM, then the general support patch, with the defconfig on top.
For the DT parts: please try to emulate the future situation, so put the
files in the directories where they would end up eventually. You can try
to take the Linux DT binding patch (for clock and reset), and just
change the paths in there to point to the respective dts/upstream
directories. This is what would happen anyway, look for those
cherry-picks and upstream references in the dts/upstream git log.
And the patch(es) wouldn't be taken as such anyway, but they provide a
test base and reference for other people, until the DT lands.
There is no need to send a new version now, just wait until you receive
some review or other comments.
Cheers,
Andre
>
> Tested on a PB629.
>
> Pablo Mazzini (7):
> sunxi: add support for the Allwinner B288
> sunxi: dram: support the Allwinner B288
> dt-bindings: clock: add the Allwinner B288 CCU
> clk: sunxi: add the Allwinner B288 gates and resets
> pinctrl: sunxi: add the Allwinner B288 PIO
> mmc: sunxi: B288 mmc0/mmc1 run off PLL_PERIPH0 2x
> sunxi: add the PocketBook Verse
>
> arch/arm/cpu/armv7/sunxi/psci.c | 9 +-
> arch/arm/dts/Makefile | 2 +
> arch/arm/dts/sun8i-b288-pocketbook-verse.dts | 114 ++++++++
> arch/arm/dts/sun8i-b288.dtsi | 292 +++++++++++++++++++
> arch/arm/include/asm/arch-sunxi/cpu.h | 1 +
> arch/arm/include/asm/arch-sunxi/cpu_sun4i.h | 16 +-
> arch/arm/mach-sunxi/Kconfig | 14 +
> arch/arm/mach-sunxi/board.c | 4 +
> arch/arm/mach-sunxi/clock_sun6i.c | 1 +
> arch/arm/mach-sunxi/cpu_info.c | 2 +
> arch/arm/mach-sunxi/dram_sunxi_dw.c | 97 +++++-
> board/sunxi/MAINTAINERS | 6 +
> configs/pocketbook_verse_defconfig | 10 +
> drivers/clk/sunxi/Kconfig | 7 +
> drivers/clk/sunxi/Makefile | 1 +
> drivers/clk/sunxi/clk_b288.c | 101 +++++++
> drivers/clk/sunxi/clk_sunxi.c | 5 +
> drivers/mmc/sunxi_mmc.c | 7 +
> drivers/pinctrl/sunxi/Kconfig | 5 +
> drivers/pinctrl/sunxi/pinctrl-sunxi.c | 22 ++
> include/dt-bindings/clock/sun8i-b288-ccu.h | 82 ++++++
> include/dt-bindings/reset/sun8i-b288-ccu.h | 45 +++
> include/sunxi_gpio.h | 1 +
> 23 files changed, 827 insertions(+), 17 deletions(-)
> create mode 100644 arch/arm/dts/sun8i-b288-pocketbook-verse.dts
> create mode 100644 arch/arm/dts/sun8i-b288.dtsi
> create mode 100644 configs/pocketbook_verse_defconfig
> create mode 100644 drivers/clk/sunxi/clk_b288.c
> create mode 100644 include/dt-bindings/clock/sun8i-b288-ccu.h
> create mode 100644 include/dt-bindings/reset/sun8i-b288-ccu.h
>
>
> base-commit: 65a7532545336e4b73e049a69436e255da7df961
^ permalink raw reply [flat|nested] 10+ messages in thread* Re: [PATCH 0/7] sunxi: add the Allwinner B288 and the PocketBook Verse
2026-10-16 17:28 ` [PATCH 0/7] sunxi: add the Allwinner B288 and " Andre Przywara
@ 2026-10-16 18:38 ` Pablo Mazzini
0 siblings, 0 replies; 10+ messages in thread
From: Pablo Mazzini @ 2026-10-16 18:38 UTC (permalink / raw)
To: Andre Przywara; +Cc: u-boot, Tom Rini, linux-sunxi
Hi Andre,
Thanks for having a look. I'll reorder the patches and move the DT
bits to dts/upstream for v2, once there's more feedback.
Pablo
On Fri, Oct 16, 2026 at 6:28 PM Andre Przywara <andre.przywara@arm.com> wrote:
>
> Hi Pablo,
>
> On 10/16/26 11:16, Pablo Mazzini wrote:
> > The Allwinner B288 (sun8iw10p1) is a dual Cortex-A7 SoC used in e-book
> > readers. This series adds SPL and U-Boot support for it, and one board:
> > the PocketBook Verse (PB629).
> > > The DT is still under review for Linux. Until it reaches
> > dts/upstream, the last patch carries a copy in arch/arm/dts.
>
> Thanks for sending this, much appreciated. I had a coarse look over
> this, and this looks fine on the first glance.
> As you said, this is somewhat blocked on the DT merge on the Linux side,
> which will probably not happen this year anymore (v7.5-rc1 would be the
> earliest).
> But meanwhile, in preparation for that, could you please reorder the
> patches, so you enable the devices first (clocks, pinctrl, mmc), then
> DRAM, then the general support patch, with the defconfig on top.
>
> For the DT parts: please try to emulate the future situation, so put the
> files in the directories where they would end up eventually. You can try
> to take the Linux DT binding patch (for clock and reset), and just
> change the paths in there to point to the respective dts/upstream
> directories. This is what would happen anyway, look for those
> cherry-picks and upstream references in the dts/upstream git log.
> And the patch(es) wouldn't be taken as such anyway, but they provide a
> test base and reference for other people, until the DT lands.
>
> There is no need to send a new version now, just wait until you receive
> some review or other comments.
>
> Cheers,
> Andre
>
> >
> > Tested on a PB629.
> >
> > Pablo Mazzini (7):
> > sunxi: add support for the Allwinner B288
> > sunxi: dram: support the Allwinner B288
> > dt-bindings: clock: add the Allwinner B288 CCU
> > clk: sunxi: add the Allwinner B288 gates and resets
> > pinctrl: sunxi: add the Allwinner B288 PIO
> > mmc: sunxi: B288 mmc0/mmc1 run off PLL_PERIPH0 2x
> > sunxi: add the PocketBook Verse
> >
> > arch/arm/cpu/armv7/sunxi/psci.c | 9 +-
> > arch/arm/dts/Makefile | 2 +
> > arch/arm/dts/sun8i-b288-pocketbook-verse.dts | 114 ++++++++
> > arch/arm/dts/sun8i-b288.dtsi | 292 +++++++++++++++++++
> > arch/arm/include/asm/arch-sunxi/cpu.h | 1 +
> > arch/arm/include/asm/arch-sunxi/cpu_sun4i.h | 16 +-
> > arch/arm/mach-sunxi/Kconfig | 14 +
> > arch/arm/mach-sunxi/board.c | 4 +
> > arch/arm/mach-sunxi/clock_sun6i.c | 1 +
> > arch/arm/mach-sunxi/cpu_info.c | 2 +
> > arch/arm/mach-sunxi/dram_sunxi_dw.c | 97 +++++-
> > board/sunxi/MAINTAINERS | 6 +
> > configs/pocketbook_verse_defconfig | 10 +
> > drivers/clk/sunxi/Kconfig | 7 +
> > drivers/clk/sunxi/Makefile | 1 +
> > drivers/clk/sunxi/clk_b288.c | 101 +++++++
> > drivers/clk/sunxi/clk_sunxi.c | 5 +
> > drivers/mmc/sunxi_mmc.c | 7 +
> > drivers/pinctrl/sunxi/Kconfig | 5 +
> > drivers/pinctrl/sunxi/pinctrl-sunxi.c | 22 ++
> > include/dt-bindings/clock/sun8i-b288-ccu.h | 82 ++++++
> > include/dt-bindings/reset/sun8i-b288-ccu.h | 45 +++
> > include/sunxi_gpio.h | 1 +
> > 23 files changed, 827 insertions(+), 17 deletions(-)
> > create mode 100644 arch/arm/dts/sun8i-b288-pocketbook-verse.dts
> > create mode 100644 arch/arm/dts/sun8i-b288.dtsi
> > create mode 100644 configs/pocketbook_verse_defconfig
> > create mode 100644 drivers/clk/sunxi/clk_b288.c
> > create mode 100644 include/dt-bindings/clock/sun8i-b288-ccu.h
> > create mode 100644 include/dt-bindings/reset/sun8i-b288-ccu.h
> >
> >
> > base-commit: 65a7532545336e4b73e049a69436e255da7df961
>
^ permalink raw reply [flat|nested] 10+ messages in thread