RE: [PATCH] omap4: Fix ULPI PHY init for ES1.0 SDP (Re: 4430SDP boot failure)

[Anand Gadiyar <gadiyar@ti.com>]

Tony Lindgren wrote:

> Here's one more es1.0 fix after the recent USB changes.
>
> Regards,
>
> Tony
>
>
> Author: Tony Lindgren <tony@atomide.com>
> Date:   Tue Jan 11 15:03:03 2011 -0800
>
>     omap4: Fix ULPI PHY init for ES1.0 SDP
>
>     Commit 6aa85a5ae610106d89e50c7e1f760c56d12f9bc4 (omap4: 4430sdp:
>     enable the ehci port on 4430SDP) added code to enable EHCI
>     support on 4430sdp board.
>
>     Looks like the ULPI pin does not seem to be muxed properly on ES1.0
>     SDP and this causes the system to reboot when the ULPI PHY is
>     enabled.
>
>     Fix this by muxing the pin, this is the same setting for
>     both ES1.0 and ES2.0. Also add checking for gpio_request.
>
>     Cc: Keshava Munegowda <keshava_mgowda@ti.com
>     Signed-off-by: Tony Lindgren <tony@atomide.com>
>
> --- a/arch/arm/mach-omap2/board-4430sdp.c
> +++ b/arch/arm/mach-omap2/board-4430sdp.c
> @@ -554,6 +554,7 @@ static void __init omap_sfh7741prox_init(void)
>
>  #ifdef CONFIG_OMAP_MUX
>  static struct omap_board_mux board_mux[] __initdata = {
> +	OMAP4_MUX(USBB2_ULPITLL_CLK, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
>  	{ .reg_offset = OMAP_MUX_TERMINATOR },
>  };
>  #else

Tony,

I believe this fix is fixing your reboot issue, but it's breaking
EHCI support on the SDP.

The MODE4 above should really be MODE3 - all GPIOs are on MODE3.
By changing

The patch snippet below fixes EHCI on the SDP, but I believe that
making this change will reintroduce the "board reboots" issue
you originally reported. Could you check and tell me if this
is the case?

Just curious - is your board a Blaze, or an SDP?

diff --git a/arch/arm/mach-omap2/board-4430sdp.c
b/arch/arm/mach-omap2/board-4430sdp.c
index 07d1b20..ab9fb4d 100644
--- a/arch/arm/mach-omap2/board-4430sdp.c
+++ b/arch/arm/mach-omap2/board-4430sdp.c
@@ -554,7 +554,7 @@ static void __init omap_sfh7741prox_init(void)

 #ifdef CONFIG_OMAP_MUX
 static struct omap_board_mux board_mux[] __initdata = {
-	OMAP4_MUX(USBB2_ULPITLL_CLK, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
+	OMAP4_MUX(USBB2_ULPITLL_CLK, OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT),
 	{ .reg_offset = OMAP_MUX_TERMINATOR },
 };
 #else