* fsl-image-gui setup eth0 static
@ 2013-08-04 11:38 Joerg Boge
2013-08-04 19:09 ` Otavio Salvador
0 siblings, 1 reply; 7+ messages in thread
From: Joerg Boge @ 2013-08-04 11:38 UTC (permalink / raw)
To: meta-freescale
[-- Attachment #1: Type: text/plain, Size: 1321 bytes --]
I want to have static ip
so i changed /etc/network/interfaces
# /etc/network/interfaces -- configuration file for ifup(8), ifdown(8)
# The loopback interface
auto lo
iface lo inet loopback
# Wireless interfaces
iface wlan0 inet dhcp
wireless_mode managed
wireless_essid any
wpa-driver wext
wpa-conf /etc/wpa_supplicant.conf
iface atml0 inet dhcp
# Wired or wireless interfaces
auto eth0
iface eth0 inet static
address 192.168.2.8
netmask 255.255.255.0
network 192.168.2.254
gateway 192.168.2.1
iface eth1 inet dhcp
# Ethernet/RNDIS gadget (g_ether)
# ... or on host side, usbnet and random hwaddr
iface usb0 inet static
address 192.168.7.2
netmask 255.255.255.0
network 192.168.7.0
gateway 192.168.7.1
# Bluetooth networking
iface bnep0 inet dhcp
do ifdown eth0
ifup eth0
and I can connect to static ip
after reboot there is no connection to the static ip possible and a
_new_ dynamic ip is taken via dhcp.
i do ifdown and ifup again. now i can connect via ssh to static and the
dynamic ip.
that is normal?
Joerg
[-- Attachment #2: Type: text/html, Size: 2385 bytes --]
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: fsl-image-gui setup eth0 static
2013-08-04 11:38 fsl-image-gui setup eth0 static Joerg Boge
@ 2013-08-04 19:09 ` Otavio Salvador
2013-08-04 19:45 ` Joerg Boge
2013-08-04 21:10 ` Joerg Boge
0 siblings, 2 replies; 7+ messages in thread
From: Otavio Salvador @ 2013-08-04 19:09 UTC (permalink / raw)
To: Joerg Boge; +Cc: meta-freescale@yoctoproject.org
On Sun, Aug 4, 2013 at 8:38 AM, Joerg Boge <joerg.boge@gmx.de> wrote:
> I want to have static ip
>
> so i changed /etc/network/interfaces
>
> # /etc/network/interfaces -- configuration file for ifup(8), ifdown(8)
>
> # The loopback interface
> auto lo
> iface lo inet loopback
>
> # Wireless interfaces
> iface wlan0 inet dhcp
> wireless_mode managed
> wireless_essid any
> wpa-driver wext
> wpa-conf /etc/wpa_supplicant.conf
>
> iface atml0 inet dhcp
>
> # Wired or wireless interfaces
> auto eth0
> iface eth0 inet static
> address 192.168.2.8
> netmask 255.255.255.0
> network 192.168.2.254
> gateway 192.168.2.1
> iface eth1 inet dhcp
>
> # Ethernet/RNDIS gadget (g_ether)
> # ... or on host side, usbnet and random hwaddr
> iface usb0 inet static
> address 192.168.7.2
> netmask 255.255.255.0
> network 192.168.7.0
> gateway 192.168.7.1
>
> # Bluetooth networking
> iface bnep0 inet dhcp
>
>
>
> do ifdown eth0
> ifup eth0
>
> and I can connect to static ip
>
> after reboot there is no connection to the static ip possible and a new
> dynamic ip is taken via dhcp.
>
> i do ifdown and ifup again. now i can connect via ssh to static and the
> dynamic ip.
>
> that is normal?
Yes and no.
fsl-image-gui is using connman for network management so you need to
set IP there. Please make your own image for specific needs as this
one is not intended to be used for long time but just as testing/demo.
--
Otavio Salvador O.S. Systems
http://www.ossystems.com.br http://projetos.ossystems.com.br
Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: fsl-image-gui setup eth0 static
2013-08-04 19:09 ` Otavio Salvador
@ 2013-08-04 19:45 ` Joerg Boge
2013-08-05 16:22 ` Daiane Angolini
2013-08-04 21:10 ` Joerg Boge
1 sibling, 1 reply; 7+ messages in thread
From: Joerg Boge @ 2013-08-04 19:45 UTC (permalink / raw)
To: Otavio Salvador; +Cc: meta-freescale@yoctoproject.org
On 08/04/2013 09:09 PM, Otavio Salvador wrote:
> On Sun, Aug 4, 2013 at 8:38 AM, Joerg Boge <joerg.boge@gmx.de> wrote:
>> I want to have static ip
>>
>> so i changed /etc/network/interfaces
>>
>> # /etc/network/interfaces -- configuration file for ifup(8), ifdown(8)
>>
>> # The loopback interface
>> auto lo
>> iface lo inet loopback
>>
>> # Wireless interfaces
>> iface wlan0 inet dhcp
>> wireless_mode managed
>> wireless_essid any
>> wpa-driver wext
>> wpa-conf /etc/wpa_supplicant.conf
>>
>> iface atml0 inet dhcp
>>
>> # Wired or wireless interfaces
>> auto eth0
>> iface eth0 inet static
>> address 192.168.2.8
>> netmask 255.255.255.0
>> network 192.168.2.254
>> gateway 192.168.2.1
>> iface eth1 inet dhcp
>>
>> # Ethernet/RNDIS gadget (g_ether)
>> # ... or on host side, usbnet and random hwaddr
>> iface usb0 inet static
>> address 192.168.7.2
>> netmask 255.255.255.0
>> network 192.168.7.0
>> gateway 192.168.7.1
>>
>> # Bluetooth networking
>> iface bnep0 inet dhcp
>>
>>
>>
>> do ifdown eth0
>> ifup eth0
>>
>> and I can connect to static ip
>>
>> after reboot there is no connection to the static ip possible and a new
>> dynamic ip is taken via dhcp.
>>
>> i do ifdown and ifup again. now i can connect via ssh to static and the
>> dynamic ip.
>>
>> that is normal?
> Yes and no.
>
> fsl-image-gui is using connman for network management so you need to
> set IP there. Please make your own image for specific needs as this
> one is not intended to be used for long time but just as testing/demo.
>
I waiting for Task #10 - How to create a custom layer from Yocto
Training Home ;)
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: fsl-image-gui setup eth0 static
2013-08-04 19:09 ` Otavio Salvador
2013-08-04 19:45 ` Joerg Boge
@ 2013-08-04 21:10 ` Joerg Boge
2013-08-04 21:51 ` Otavio Salvador
1 sibling, 1 reply; 7+ messages in thread
From: Joerg Boge @ 2013-08-04 21:10 UTC (permalink / raw)
To: Otavio Salvador; +Cc: meta-freescale@yoctoproject.org
On 08/04/2013 09:09 PM, Otavio Salvador wrote:
> On Sun, Aug 4, 2013 at 8:38 AM, Joerg Boge <joerg.boge@gmx.de> wrote:
>> I want to have static ip
>>
>> so i changed /etc/network/interfaces
>>
>> # /etc/network/interfaces -- configuration file for ifup(8), ifdown(8)
>>
>> # The loopback interface
>> auto lo
>> iface lo inet loopback
>>
>> # Wireless interfaces
>> iface wlan0 inet dhcp
>> wireless_mode managed
>> wireless_essid any
>> wpa-driver wext
>> wpa-conf /etc/wpa_supplicant.conf
>>
>> iface atml0 inet dhcp
>>
>> # Wired or wireless interfaces
>> auto eth0
>> iface eth0 inet static
>> address 192.168.2.8
>> netmask 255.255.255.0
>> network 192.168.2.254
>> gateway 192.168.2.1
>> iface eth1 inet dhcp
>>
>> # Ethernet/RNDIS gadget (g_ether)
>> # ... or on host side, usbnet and random hwaddr
>> iface usb0 inet static
>> address 192.168.7.2
>> netmask 255.255.255.0
>> network 192.168.7.0
>> gateway 192.168.7.1
>>
>> # Bluetooth networking
>> iface bnep0 inet dhcp
>>
>>
>>
>> do ifdown eth0
>> ifup eth0
>>
>> and I can connect to static ip
>>
>> after reboot there is no connection to the static ip possible and a new
>> dynamic ip is taken via dhcp.
>>
>> i do ifdown and ifup again. now i can connect via ssh to static and the
>> dynamic ip.
>>
>> that is normal?
> Yes and no.
>
> fsl-image-gui is using connman for network management so you need to
> set IP there. Please make your own image for specific needs as this
> one is not intended to be used for long time but just as testing/demo.
>
I goggled something out about connman.
So to set up it with static ip "connman-tests" are needed
so will be nice it will be added in the future
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: fsl-image-gui setup eth0 static
2013-08-04 21:10 ` Joerg Boge
@ 2013-08-04 21:51 ` Otavio Salvador
0 siblings, 0 replies; 7+ messages in thread
From: Otavio Salvador @ 2013-08-04 21:51 UTC (permalink / raw)
To: Joerg Boge; +Cc: meta-freescale@yoctoproject.org
On Sun, Aug 4, 2013 at 6:10 PM, Joerg Boge <joerg.boge@gmx.de> wrote:
> On 08/04/2013 09:09 PM, Otavio Salvador wrote:
>>
>> On Sun, Aug 4, 2013 at 8:38 AM, Joerg Boge <joerg.boge@gmx.de> wrote:
>>>
>>> I want to have static ip
>>>
>>> so i changed /etc/network/interfaces
>>>
>>> # /etc/network/interfaces -- configuration file for ifup(8), ifdown(8)
>>>
>>> # The loopback interface
>>> auto lo
>>> iface lo inet loopback
>>>
>>> # Wireless interfaces
>>> iface wlan0 inet dhcp
>>> wireless_mode managed
>>> wireless_essid any
>>> wpa-driver wext
>>> wpa-conf /etc/wpa_supplicant.conf
>>>
>>> iface atml0 inet dhcp
>>>
>>> # Wired or wireless interfaces
>>> auto eth0
>>> iface eth0 inet static
>>> address 192.168.2.8
>>> netmask 255.255.255.0
>>> network 192.168.2.254
>>> gateway 192.168.2.1
>>> iface eth1 inet dhcp
>>>
>>> # Ethernet/RNDIS gadget (g_ether)
>>> # ... or on host side, usbnet and random hwaddr
>>> iface usb0 inet static
>>> address 192.168.7.2
>>> netmask 255.255.255.0
>>> network 192.168.7.0
>>> gateway 192.168.7.1
>>>
>>> # Bluetooth networking
>>> iface bnep0 inet dhcp
>>>
>>>
>>>
>>> do ifdown eth0
>>> ifup eth0
>>>
>>> and I can connect to static ip
>>>
>>> after reboot there is no connection to the static ip possible and a
>>> new
>>> dynamic ip is taken via dhcp.
>>>
>>> i do ifdown and ifup again. now i can connect via ssh to static and the
>>> dynamic ip.
>>>
>>> that is normal?
>>
>> Yes and no.
>>
>> fsl-image-gui is using connman for network management so you need to
>> set IP there. Please make your own image for specific needs as this
>> one is not intended to be used for long time but just as testing/demo.
>>
>
> I goggled something out about connman.
>
> So to set up it with static ip "connman-tests" are needed
>
> so will be nice it will be added in the future
You can do it in the GUI AFAIK.
--
Otavio Salvador O.S. Systems
http://www.ossystems.com.br http://projetos.ossystems.com.br
Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: fsl-image-gui setup eth0 static
2013-08-04 19:45 ` Joerg Boge
@ 2013-08-05 16:22 ` Daiane Angolini
2013-08-05 16:46 ` Joerg boge
0 siblings, 1 reply; 7+ messages in thread
From: Daiane Angolini @ 2013-08-05 16:22 UTC (permalink / raw)
To: Joerg Boge; +Cc: meta-freescale@yoctoproject.org, Otavio Salvador
On 08/04/2013 04:45 PM, Joerg Boge wrote:
> On 08/04/2013 09:09 PM, Otavio Salvador wrote:
>> On Sun, Aug 4, 2013 at 8:38 AM, Joerg Boge <joerg.boge@gmx.de> wrote:
>>> I want to have static ip
>>>
>>> so i changed /etc/network/interfaces
>>>
>>> # /etc/network/interfaces -- configuration file for ifup(8), ifdown(8)
>>>
>>> # The loopback interface
>>> auto lo
>>> iface lo inet loopback
>>>
>>> # Wireless interfaces
>>> iface wlan0 inet dhcp
>>> wireless_mode managed
>>> wireless_essid any
>>> wpa-driver wext
>>> wpa-conf /etc/wpa_supplicant.conf
>>>
>>> iface atml0 inet dhcp
>>>
>>> # Wired or wireless interfaces
>>> auto eth0
>>> iface eth0 inet static
>>> address 192.168.2.8
>>> netmask 255.255.255.0
>>> network 192.168.2.254
>>> gateway 192.168.2.1
>>> iface eth1 inet dhcp
>>>
>>> # Ethernet/RNDIS gadget (g_ether)
>>> # ... or on host side, usbnet and random hwaddr
>>> iface usb0 inet static
>>> address 192.168.7.2
>>> netmask 255.255.255.0
>>> network 192.168.7.0
>>> gateway 192.168.7.1
>>>
>>> # Bluetooth networking
>>> iface bnep0 inet dhcp
>>>
>>>
>>>
>>> do ifdown eth0
>>> ifup eth0
>>>
>>> and I can connect to static ip
>>>
>>> after reboot there is no connection to the static ip possible and
>>> a new
>>> dynamic ip is taken via dhcp.
>>>
>>> i do ifdown and ifup again. now i can connect via ssh to static and the
>>> dynamic ip.
>>>
>>> that is normal?
>> Yes and no.
>>
>> fsl-image-gui is using connman for network management so you need to
>> set IP there. Please make your own image for specific needs as this
>> one is not intended to be used for long time but just as testing/demo.
>>
> I waiting for Task #10 - How to create a custom layer from Yocto
> Training Home ;)
>
I'm baking it right now :D
If you have other topic idea, please, let me know
--
Daiane
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: fsl-image-gui setup eth0 static
2013-08-05 16:22 ` Daiane Angolini
@ 2013-08-05 16:46 ` Joerg boge
0 siblings, 0 replies; 7+ messages in thread
From: Joerg boge @ 2013-08-05 16:46 UTC (permalink / raw)
To: Daiane Angolini; +Cc: meta-freescale@yoctoproject.org, Otavio Salvador
Am 05.08.2013 18:22, schrieb Daiane Angolini:
> On 08/04/2013 04:45 PM, Joerg Boge wrote:
>> On 08/04/2013 09:09 PM, Otavio Salvador wrote:
>>> On Sun, Aug 4, 2013 at 8:38 AM, Joerg Boge <joerg.boge@gmx.de> wrote:
>>>> I want to have static ip
>>>>
>>>> so i changed /etc/network/interfaces
>>>>
>>>> # /etc/network/interfaces -- configuration file for ifup(8), ifdown(8)
>>>>
>>>> # The loopback interface
>>>> auto lo
>>>> iface lo inet loopback
>>>>
>>>> # Wireless interfaces
>>>> iface wlan0 inet dhcp
>>>> wireless_mode managed
>>>> wireless_essid any
>>>> wpa-driver wext
>>>> wpa-conf /etc/wpa_supplicant.conf
>>>>
>>>> iface atml0 inet dhcp
>>>>
>>>> # Wired or wireless interfaces
>>>> auto eth0
>>>> iface eth0 inet static
>>>> address 192.168.2.8
>>>> netmask 255.255.255.0
>>>> network 192.168.2.254
>>>> gateway 192.168.2.1
>>>> iface eth1 inet dhcp
>>>>
>>>> # Ethernet/RNDIS gadget (g_ether)
>>>> # ... or on host side, usbnet and random hwaddr
>>>> iface usb0 inet static
>>>> address 192.168.7.2
>>>> netmask 255.255.255.0
>>>> network 192.168.7.0
>>>> gateway 192.168.7.1
>>>>
>>>> # Bluetooth networking
>>>> iface bnep0 inet dhcp
>>>>
>>>>
>>>>
>>>> do ifdown eth0
>>>> ifup eth0
>>>>
>>>> and I can connect to static ip
>>>>
>>>> after reboot there is no connection to the static ip possible and
>>>> a new
>>>> dynamic ip is taken via dhcp.
>>>>
>>>> i do ifdown and ifup again. now i can connect via ssh to static and
>>>> the
>>>> dynamic ip.
>>>>
>>>> that is normal?
>>> Yes and no.
>>>
>>> fsl-image-gui is using connman for network management so you need to
>>> set IP there. Please make your own image for specific needs as this
>>> one is not intended to be used for long time but just as testing/demo.
>>>
>> I waiting for Task #10 - How to create a custom layer from Yocto
>> Training Home ;)
>>
>
> I'm baking it right now :D
>
> If you have other topic idea, please, let me know
A How to create machine layer will be useful
Good baking ;)
Joerg
^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2013-08-05 16:46 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2013-08-04 11:38 fsl-image-gui setup eth0 static Joerg Boge
2013-08-04 19:09 ` Otavio Salvador
2013-08-04 19:45 ` Joerg Boge
2013-08-05 16:22 ` Daiane Angolini
2013-08-05 16:46 ` Joerg boge
2013-08-04 21:10 ` Joerg Boge
2013-08-04 21:51 ` Otavio Salvador
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.