* Re: Install options on AXi
1999-09-17 19:43 Install options on AXi Brent Jay Thorpe
@ 1999-09-17 21:21 ` David A. Cooley
1999-09-17 22:32 ` Jakub Jelinek
1999-09-18 1:38 ` David S. Miller
2 siblings, 0 replies; 4+ messages in thread
From: David A. Cooley @ 1999-09-17 21:21 UTC (permalink / raw)
To: ultralinux
At 03:43 PM 9/17/99 -0400, Brent Jay Thorpe wrote:
>All,
>
>I have to make a customer presentation about install options with Linux
>on AXi (CDROM, Floppy, Network.) I have been doing some homework in
>making the "slideware" and found that you could get the initial boot
>loader from a floppy device (as well as tftp.) In following the
>instructions on creating the floppy, I found that my system does not
>recognize the floppy device as a valid block device. In other words, it
>cannot see the floppy device at all. I also found out that it does not
>recognize the printer port (lp0) either. Anyone know what is the
>correct device for both the floppy and printer on an AXi?
Brent,
I believe the AXi is an UltraSparc based board... None of the Linux ports
to sparc support the Floppy for boot, and the lp port is only supported
experimentally.
============================= David Cooley N5XMT Internet: N5XMT@bellsouth.net
Packet: N5XMT@KQ4LO.#INT.NC.USA.NA T.A.P.R. Member #7068
Sponges grow in the ocean... Wonder how deep it would be if they didn't?!
=============================
^ permalink raw reply [flat|nested] 4+ messages in thread* Re: Install options on AXi
1999-09-17 19:43 Install options on AXi Brent Jay Thorpe
1999-09-17 21:21 ` David A. Cooley
@ 1999-09-17 22:32 ` Jakub Jelinek
1999-09-18 1:38 ` David S. Miller
2 siblings, 0 replies; 4+ messages in thread
From: Jakub Jelinek @ 1999-09-17 22:32 UTC (permalink / raw)
To: ultralinux
On Fri, Sep 17, 1999 at 03:43:22PM -0400, Brent Jay Thorpe wrote:
> All,
>
> I have to make a customer presentation about install options with Linux
> on AXi (CDROM, Floppy, Network.) I have been doing some homework in
> making the "slideware" and found that you could get the initial boot
> loader from a floppy device (as well as tftp.) In following the
> instructions on creating the floppy, I found that my system does not
> recognize the floppy device as a valid block device. In other words, it
> cannot see the floppy device at all.
Have you tried /dev/fd0 or /dev/fd1 as the device? Some AX and AXi boxes
have these swapped, so even if you only have one floppy, it might be
/dev/fd1. See bootup dmesg which one do you have. (It is a hardware issue).
> I also found out that it does not
> recognize the printer port (lp0) either. Anyone know what is the
> correct device for both the floppy and printer on an AXi?
Have you loaded all the required modules for the parallel port?
You need probably parport_ax, parport and lp modules.
Cheers,
Jakub
___________________________________________________________________
Jakub Jelinek | jj@sunsite.mff.cuni.cz | http://sunsite.mff.cuni.cz
Administrator of SunSITE Czech Republic, MFF, Charles University
___________________________________________________________________
UltraLinux | http://ultra.linux.cz/ | http://ultra.penguin.cz/
Linux version 2.3.18 on a sparc64 machine (1343.49 BogoMips)
___________________________________________________________________
^ permalink raw reply [flat|nested] 4+ messages in thread* Re: Install options on AXi
1999-09-17 19:43 Install options on AXi Brent Jay Thorpe
1999-09-17 21:21 ` David A. Cooley
1999-09-17 22:32 ` Jakub Jelinek
@ 1999-09-18 1:38 ` David S. Miller
2 siblings, 0 replies; 4+ messages in thread
From: David S. Miller @ 1999-09-18 1:38 UTC (permalink / raw)
To: ultralinux
Date: Fri, 17 Sep 1999 17:21:09 -0400
From: "David A. Cooley" <n5xmt@bellsouth.net>
I believe the AXi is an UltraSparc based board... None of the Linux
ports to sparc support the Floppy for boot, and the lp port is only
supported experimentally.
This is not true at all. The situation in a nutshell is:
1) All 32-bit Sparc systems should work with a floppy boot.
2) Most UltraSparc systems do not, these include all SBUS UltraSparc
systems and Ultra10, Ultra5, Ultra30, Ultra60 PCI systems. This
is due to a bug in the OBP firmware shipped in those machines, and
is not our doing :-)
All system level board UltraSparc/PCI systems shipped by SME
such as the AXi and AXmp should work with floppy boot because they
lack the OBP firmware bug, as far as we've been told.
3) parallel port is fully supported on PCI systems, it is only
experimental and not fully supported on SBUS systems, we are
working to correct this SBUS issue for 2.4.x kernels
Most people having problems with the parallel port on PCI
UltraSparcs turn out to not have loaded the appropriate kernel
modules.
Later,
David S. Miller
davem@redhat.com
^ permalink raw reply [flat|nested] 4+ messages in thread