[PATCH i-g-t v10 46/49] docs/unigraf: Add unigraf documentation

[Louis Chauvet <louis.chauvet@bootlin.com>]

Add unigraf documentation to explain how to compile and use it with IGT.

Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
---
 docs/unigraf.txt | 81 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 81 insertions(+)

diff --git a/docs/unigraf.txt b/docs/unigraf.txt
new file mode 100644
index 000000000000..37996a2ef98b
--- /dev/null
+++ b/docs/unigraf.txt
@@ -0,0 +1,81 @@
+Unigraf Support in IGT
+========================
+
+This document provides information and instructions for Unigraf support in IGT.
+
+Introduction
+------------
+
+Unigraf devices are a set of devices that can be used to test all sort of graphical
+interface and signals. See Unigraf website for more information about all the
+capabilities of each devices: https://unigraf.fi
+
+Unigraf documentation
+---------------------
+
+All the documentation for libTSI, the library used to communicate with the unigraf,
+can be found on unigraf website: https://www.unigraf.fi/downloads/
+
+Setting up Unigraf
+------------------
+
+For most of the unigraf devices, this should be as simple as "plugging the
+unigraf and plug the video cable". If you need to install some license, upgrade
+the firmware... please take a look at the official unigraf documentation.
+
+Compiling IGT with Unigraf support
+----------------------------------
+
+Unfortunately, the communication with the device use a proprietary library and the
+underlying protocol is not open. To use the unigraf you need to install the unigraf
+SDK, grab the libTSI.so and make it available on the build machine and the DUT.
+
+Deploying the Unigraf with IGT
+------------------------------
+
+Unigraf may work out of the box: by default if IGT find a unigraf device, it will
+try to connect and configure it to use USB-C input. This allows running most of
+the existing tests without an actual screens.
+
+Here is a complete example configuration:
+
+        [Unigraf]
+        # Choose a device using his name, you can find it in UCDConsole (installed with the SDK)
+        Device=UCD-500 [2434C620]
+        # Choose a role for the device, you can find it UCDConsole
+        Role=USB-C, DP Alt Mode Source and Sink
+        # Choose active input for the device
+        Input=DP RX
+        # Set the connector name used by the unigraf device. If not set, IGT will try to
+        # autodetect which connector is used.
+        Connector=DP-2
+        # Set the EDID used by Unigraf
+        EDID=DEL_16543_DELL_P2314T_DP
+        # Enable or disable the use of Unigraf's CRCs instead of the CRTC CRCs
+        UseCRC=1
+        # Set the number of emulated MST streams (0 = Single Stream Transport, >=1 = MST)
+        MSTStreams=0
+
+Current Support in IGT
+----------------------
+
+Support for the Unigraf devices in IGT is found in the following places:
+* lib/unigraf/unigraf.[ch] -> IGT API
+* lib/unigraf/TSI.h -> Header for libTSI.so, not provided by Unigraf
+* lib/unigraf/TSI_types.h -> Header containing all the relevant values from unigraf SDK. The unigraf SDK can't be used directly because it is only compatible with windows and c++.
+
+Current unigraf.c features are:
+* Plug, unplug, hotplug pulse
+* EDID management
+* MST/SST stream management
+* CRC calculation
+
+Current testing are:
+* All igt tests that require a display and use a CRC (kms_plane, kms_cursor_crc, ...)
+* Basic EDID and MST tests
+
+Planned tests:
+* Link training scenarios (link rate, lane count, scrambling, ...)
+* Bandwidth constraint management
+* HDCP content protection
+* Display stream compression

-- 
2.52.0