Linux kernel and device drivers for NXP i.MX platforms
 help / color / mirror / Atom feed
From: Frank Li <Frank.li@nxp.com>
To: Vladimir Zapolskiy <vz@mleia.com>
Cc: Piotr Wojtaszczyk <piotr.wojtaszczyk@timesys.com>,
	Rob Herring <robh@kernel.org>,
	Krzysztof Kozlowski <krzk+dt@kernel.org>,
	Conor Dooley <conor+dt@kernel.org>,
	"moderated list:ARM/LPC32XX SOC SUPPORT"
	<linux-arm-kernel@lists.infradead.org>,
	"open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS"
	<devicetree@vger.kernel.org>,
	open list <linux-kernel@vger.kernel.org>,
	imx@lists.linux.dev
Subject: Re: [PATCH 4/5] ARM: dts: lpc3250-phy3250: add at25 required properties
Date: Fri, 14 Nov 2025 11:14:27 -0500	[thread overview]
Message-ID: <aRdVY5aMCjj4fmDB@lizhi-Precision-Tower-5810> (raw)
In-Reply-To: <4bf7223e-1611-4149-a4d6-9a3ac103e264@mleia.com>

On Fri, Nov 14, 2025 at 01:47:48AM +0200, Vladimir Zapolskiy wrote:
> Hi Frank.
>
> On 10/29/25 22:28, Frank Li wrote:
> > Add at25 required properties (size, address-width and pagesize), which
> > duplicate deprecated properties.
> >
> > Change nodename 'at25' to 'eeprom'.
> >
> > Fix below CHECK_DTB warning:
> >    arch/arm/boot/dts/nxp/lpc/lpc3250-phy3250.dtb: at25@0 (atmel,at25): 'pagesize' is a required property
> >    arch/arm/boot/dts/nxp/lpc/lpc3250-phy3250.dtb: at25@0 (atmel,at25): $nodename: 'anyOf' conditional failed, one must be fixed:
> >
> > Signed-off-by: Frank Li <Frank.Li@nxp.com>
> > ---
> >   arch/arm/boot/dts/nxp/lpc/lpc3250-phy3250.dts | 6 +++++-
> >   1 file changed, 5 insertions(+), 1 deletion(-)
> >
> > diff --git a/arch/arm/boot/dts/nxp/lpc/lpc3250-phy3250.dts b/arch/arm/boot/dts/nxp/lpc/lpc3250-phy3250.dts
> > index 21a6d0bca1e8a..15463a96938cc 100644
> > --- a/arch/arm/boot/dts/nxp/lpc/lpc3250-phy3250.dts
> > +++ b/arch/arm/boot/dts/nxp/lpc/lpc3250-phy3250.dts
> > @@ -200,7 +200,7 @@ &ssp0 {
> >   	cs-gpios = <&gpio 3 5 0>;
> >   	status = "okay";
> > -	eeprom: at25@0 {
> > +	eeprom: eeprom@0 {
> >   		compatible = "atmel,at25";
> >   		reg = <0>;
> >   		spi-max-frequency = <5000000>;
> > @@ -216,6 +216,10 @@ eeprom: at25@0 {
> >   		at25,byte-len = <0x8000>;
> >   		at25,addr-mode = <2>;
> >   		at25,page-size = <64>;
> > +
> > +		size = <0x8000>;
> > +		address-width = <16>;
> > +		pagesize = <64>;
>
> Is there any need to have both sets of properties?
>

Generally, keep old one just for back compatible. It is quite common for
this case.

I am NOT sure if it is safe enough to remove deprecated properties now.

> I'd suggest to remove the deprecated set in a separate patch, note
> that your done change is not described in the commit message.

Which part is not described?

Frank
>
> >   	};
> >   };
>
> --
> Best wishes,
> Vladimir

  reply	other threads:[~2025-11-14 16:14 UTC|newest]

Thread overview: 15+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2025-10-29 20:27 [PATCH 1/5] ARM: dts: lpc32xx: add bus surfix for simple-bus Frank Li
2025-10-29 20:27 ` [PATCH 2/5] ARM: dts: lpc32xx: add sspclk clock for SPI[0,1] Frank Li
2025-11-13 23:12   ` Vladimir Zapolskiy
2025-10-29 20:27 ` [PATCH 3/5] ARM: dts: lpc3250-ea3250: add key- prefix for gpio-keys Frank Li
2025-11-14  0:02   ` Vladimir Zapolskiy
2025-10-29 20:28 ` [PATCH 4/5] ARM: dts: lpc3250-phy3250: add at25 required properties Frank Li
2025-11-13 23:47   ` Vladimir Zapolskiy
2025-11-14 16:14     ` Frank Li [this message]
2025-11-14 16:32       ` Vladimir Zapolskiy
2025-10-29 20:28 ` [PATCH 5/5] ARM: dts: lpc32xx: update #address-cells of arm,pl175 to 2 Frank Li
2025-11-13 23:44   ` Vladimir Zapolskiy
2025-11-13 23:55 ` [PATCH 1/5] ARM: dts: lpc32xx: add bus surfix for simple-bus Vladimir Zapolskiy
2025-11-14 16:19   ` Frank Li
2025-11-14 16:44     ` Vladimir Zapolskiy
2025-11-14 16:56       ` Frank Li

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=aRdVY5aMCjj4fmDB@lizhi-Precision-Tower-5810 \
    --to=frank.li@nxp.com \
    --cc=conor+dt@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=imx@lists.linux.dev \
    --cc=krzk+dt@kernel.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=piotr.wojtaszczyk@timesys.com \
    --cc=robh@kernel.org \
    --cc=vz@mleia.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox