Linux kernel and device drivers for NXP i.MX platforms
 help / color / mirror / Atom feed
From: Vladimir Zapolskiy <vz@mleia.com>
To: Frank Li <Frank.Li@nxp.com>,
	Piotr Wojtaszczyk <piotr.wojtaszczyk@timesys.com>,
	Rob Herring <robh@kernel.org>,
	Krzysztof Kozlowski <krzk+dt@kernel.org>,
	Conor Dooley <conor+dt@kernel.org>,
	"moderated list:ARM/LPC32XX SOC SUPPORT"
	<linux-arm-kernel@lists.infradead.org>,
	"open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS"
	<devicetree@vger.kernel.org>,
	open list <linux-kernel@vger.kernel.org>
Cc: imx@lists.linux.dev
Subject: Re: [PATCH 3/5] ARM: dts: lpc3250-ea3250: add key- prefix for gpio-keys
Date: Fri, 14 Nov 2025 02:02:41 +0200	[thread overview]
Message-ID: <b4d8a2e9-46ab-460a-ba56-ff8def8e36d4@mleia.com> (raw)
In-Reply-To: <20251029202801.3963952-3-Frank.Li@nxp.com>

Hi Frank.

On 10/29/25 22:27, Frank Li wrote:
> Add key- prefix to fix below CHECK_DTB warning:
>    arch/arm/boot/dts/nxp/lpc/lpc3250-ea3250.dtb: gpio-keys (gpio-keys): 'joy0', ... do not match any of the regexes: '^(button|...)$', 'pinctrl-[0-9]+
> 
> Signed-off-by: Frank Li <Frank.Li@nxp.com>
> ---
>   arch/arm/boot/dts/nxp/lpc/lpc3250-ea3250.dts | 18 +++++++++---------
>   1 file changed, 9 insertions(+), 9 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/nxp/lpc/lpc3250-ea3250.dts b/arch/arm/boot/dts/nxp/lpc/lpc3250-ea3250.dts
> index 63c6f17bb7c9f..837a3cfa8e7c8 100644
> --- a/arch/arm/boot/dts/nxp/lpc/lpc3250-ea3250.dts
> +++ b/arch/arm/boot/dts/nxp/lpc/lpc3250-ea3250.dts
> @@ -27,55 +27,55 @@ button {
>   			gpios = <&gpio 4 1 0>; /* GPI_P3 1 */
>   		};
>   
> -		key1 {
> +		key-1 {
>   			label = "KEY1";
>   			linux,code = <1>;
>   			gpios = <&pca9532 0 0>;
>   		};
>   
> -		key2 {
> +		key-2 {
>   			label = "KEY2";
>   			linux,code = <2>;
>   			gpios = <&pca9532 1 0>;
>   		};
>   
> -		key3 {
> +		key-3 {
>   			label = "KEY3";
>   			linux,code = <3>;
>   			gpios = <&pca9532 2 0>;
>   		};
>   
> -		key4 {
> +		key-4 {
>   			label = "KEY4";
>   			linux,code = <4>;
>   			gpios = <&pca9532 3 0>;
>   		};
>   
> -		joy0 {
> +		key-joy0 {
>   			label = "Joystick Key 0";
>   			linux,code = <10>;
>   			gpios = <&gpio 2 0 0>; /* P2.0 */
>   		};
>   
> -		joy1 {
> +		key-joy1 {
>   			label = "Joystick Key 1";
>   			linux,code = <11>;
>   			gpios = <&gpio 2 1 0>; /* P2.1 */
>   		};
>   
> -		joy2 {
> +		key-joy2 {
>   			label = "Joystick Key 2";
>   			linux,code = <12>;
>   			gpios = <&gpio 2 2 0>; /* P2.2 */
>   		};
>   
> -		joy3 {
> +		key-joy3 {
>   			label = "Joystick Key 3";
>   			linux,code = <13>;
>   			gpios = <&gpio 2 3 0>; /* P2.3 */
>   		};
>   
> -		joy4 {
> +		key-joy4 {
>   			label = "Joystick Key 4";
>   			linux,code = <14>;
>   			gpios = <&gpio 2 4 0>; /* P2.4 */

Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>

Thank you for the contributions, I hope I'll find time tomorrow
to send a tiny pull request:
* lpc43xx board compatible strings,
* this change,
* any other your changes with my review comments satisfied, if I get them.

-- 
Best wishes,
Vladimir

  reply	other threads:[~2025-11-14  0:02 UTC|newest]

Thread overview: 15+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2025-10-29 20:27 [PATCH 1/5] ARM: dts: lpc32xx: add bus surfix for simple-bus Frank Li
2025-10-29 20:27 ` [PATCH 2/5] ARM: dts: lpc32xx: add sspclk clock for SPI[0,1] Frank Li
2025-11-13 23:12   ` Vladimir Zapolskiy
2025-10-29 20:27 ` [PATCH 3/5] ARM: dts: lpc3250-ea3250: add key- prefix for gpio-keys Frank Li
2025-11-14  0:02   ` Vladimir Zapolskiy [this message]
2025-10-29 20:28 ` [PATCH 4/5] ARM: dts: lpc3250-phy3250: add at25 required properties Frank Li
2025-11-13 23:47   ` Vladimir Zapolskiy
2025-11-14 16:14     ` Frank Li
2025-11-14 16:32       ` Vladimir Zapolskiy
2025-10-29 20:28 ` [PATCH 5/5] ARM: dts: lpc32xx: update #address-cells of arm,pl175 to 2 Frank Li
2025-11-13 23:44   ` Vladimir Zapolskiy
2025-11-13 23:55 ` [PATCH 1/5] ARM: dts: lpc32xx: add bus surfix for simple-bus Vladimir Zapolskiy
2025-11-14 16:19   ` Frank Li
2025-11-14 16:44     ` Vladimir Zapolskiy
2025-11-14 16:56       ` Frank Li

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=b4d8a2e9-46ab-460a-ba56-ff8def8e36d4@mleia.com \
    --to=vz@mleia.com \
    --cc=Frank.Li@nxp.com \
    --cc=conor+dt@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=imx@lists.linux.dev \
    --cc=krzk+dt@kernel.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=piotr.wojtaszczyk@timesys.com \
    --cc=robh@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox