Intel-XE Archive on lore.kernel.org
 help / color / mirror / Atom feed
From: Michal Wajdeczko <michal.wajdeczko@intel.com>
To: Matthew Brost <matthew.brost@intel.com>,
	<intel-xe@lists.freedesktop.org>
Subject: Re: [PATCH v2 12/34] drm/xe/vf: Make VF recovery run on per-GT worker
Date: Wed, 24 Sep 2025 12:49:25 +0200	[thread overview]
Message-ID: <55c5e870-6823-4fb3-80ab-0e6914d054d2@intel.com> (raw)
In-Reply-To: <20250924011601.888293-13-matthew.brost@intel.com>



On 9/24/2025 3:15 AM, Matthew Brost wrote:
> VF recovery is a per-GT operation, so it makes sense to isolate it to a

that was also my suggestion to make it per-GT, good to see it happen now

> per-GT queue. Scheduling this operation on the same worker as the GT
> reset and TDR not only aligns with this design but also helps avoid race
> conditions, as those operations can also modify the queue state.

but while the recovery is per-GT, we should still protect against that
one GT starts the recovery sooner then other GTs notice about it

> 
> v2:
>  - Fix lockdep splat (Adam)
>  - Use xe_sriov_vf_migration_supported helper
> 
> Signed-off-by: Matthew Brost <matthew.brost@intel.com>
> ---
>  drivers/gpu/drm/xe/xe_gt_sriov_vf.c       | 170 ++++++++++++++-
>  drivers/gpu/drm/xe/xe_gt_sriov_vf.h       |   3 +-
>  drivers/gpu/drm/xe/xe_gt_sriov_vf_types.h |   7 +
>  drivers/gpu/drm/xe/xe_sriov_vf.c          | 242 +---------------------
>  drivers/gpu/drm/xe/xe_sriov_vf.h          |   1 -
>  drivers/gpu/drm/xe/xe_sriov_vf_types.h    |   4 -
>  6 files changed, 169 insertions(+), 258 deletions(-)
> 
> diff --git a/drivers/gpu/drm/xe/xe_gt_sriov_vf.c b/drivers/gpu/drm/xe/xe_gt_sriov_vf.c
> index c9d0e32e7a15..cfb71b749e52 100644
> --- a/drivers/gpu/drm/xe/xe_gt_sriov_vf.c
> +++ b/drivers/gpu/drm/xe/xe_gt_sriov_vf.c
> @@ -25,11 +25,15 @@
>  #include "xe_guc.h"
>  #include "xe_guc_hxg_helpers.h"
>  #include "xe_guc_relay.h"
> +#include "xe_guc_submit.h"
> +#include "xe_irq.h"
>  #include "xe_lrc.h"
>  #include "xe_memirq.h"
>  #include "xe_mmio.h"
> +#include "xe_pm.h"
>  #include "xe_sriov.h"
>  #include "xe_sriov_vf.h"
> +#include "xe_tile_sriov_vf.h"
>  #include "xe_uc_fw.h"
>  #include "xe_wopcm.h"
>  
> @@ -314,7 +318,7 @@ static int guc_action_vf_notify_resfix_done(struct xe_guc *guc)
>   * Returns: 0 if the operation completed successfully, or a negative error
>   * code otherwise.
>   */
> -int xe_gt_sriov_vf_notify_resfix_done(struct xe_gt *gt)
> +static int xe_gt_sriov_vf_notify_resfix_done(struct xe_gt *gt)
>  {
>  	struct xe_guc *guc = &gt->uc.guc;
>  	int err;
> @@ -808,7 +812,7 @@ int xe_gt_sriov_vf_connect(struct xe_gt *gt)
>   * xe_gt_sriov_vf_default_lrcs_hwsp_rebase - Update GGTT references in HWSP of default LRCs.
>   * @gt: the &xe_gt struct instance
>   */
> -void xe_gt_sriov_vf_default_lrcs_hwsp_rebase(struct xe_gt *gt)
> +static void xe_gt_sriov_vf_default_lrcs_hwsp_rebase(struct xe_gt *gt)
>  {
>  	struct xe_hw_engine *hwe;
>  	enum xe_hw_engine_id id;
> @@ -817,6 +821,26 @@ void xe_gt_sriov_vf_default_lrcs_hwsp_rebase(struct xe_gt *gt)
>  		xe_default_lrc_update_memirq_regs_with_address(hwe);
>  }
>  
> +static void xe_gt_sriov_vf_start_migration_recovery(struct xe_gt *gt)

nit: if this is static then could be just:

	vf_start_migration_recovery(gt)

> +{
> +	bool started;
> +
> +	xe_gt_assert(gt, IS_SRIOV_VF(gt_to_xe(gt)));
> +
> +	spin_lock(&gt->sriov.vf.migration.lock);
> +
> +	if (!gt->sriov.vf.migration.recovery_queued) {
> +		gt->sriov.vf.migration.recovery_queued = true;
> +		WRITE_ONCE(gt->sriov.vf.migration.recovery_inprogress, true);
> +
> +		started = queue_work(gt->ordered_wq, &gt->sriov.vf.migration.worker);
> +		xe_gt_sriov_info(gt, "VF migration recovery %s\n", started ?
> +				 "scheduled" : "already in progress");

with this .recovery_queued flag, can we hit "already in progress" case?

> +	}
> +
> +	spin_unlock(&gt->sriov.vf.migration.lock);
> +}
> +
>  /**
>   * xe_gt_sriov_vf_migrated_event_handler - Start a VF migration recovery,
>   *   or just mark that a GuC is ready for it.
> @@ -831,15 +855,8 @@ void xe_gt_sriov_vf_migrated_event_handler(struct xe_gt *gt)
>  	xe_gt_assert(gt, IS_SRIOV_VF(xe));
>  	xe_gt_assert(gt, xe_gt_sriov_vf_recovery_inprogress(gt));
>  
> -	set_bit(gt->info.id, &xe->sriov.vf.migration.gt_flags);
> -	/*
> -	 * We need to be certain that if all flags were set, at least one
> -	 * thread will notice that and schedule the recovery.
> -	 */
> -	smp_mb__after_atomic();
> -
>  	xe_gt_sriov_info(gt, "ready for recovery after migration\n");
> -	xe_sriov_vf_start_migration_recovery(xe);
> +	xe_gt_sriov_vf_start_migration_recovery(gt);
>  }
>  
>  static bool vf_is_negotiated(struct xe_gt *gt, u16 major, u16 minor)
> @@ -1175,6 +1192,139 @@ void xe_gt_sriov_vf_print_version(struct xe_gt *gt, struct drm_printer *p)
>  		   pf_version->major, pf_version->minor);
>  }
>  
> +static void vf_post_migration_shutdown(struct xe_gt *gt)
> +{
> +	int ret = 0;
> +
> +	spin_lock_irq(&gt->sriov.vf.migration.lock);
> +	gt->sriov.vf.migration.recovery_queued = false;
> +	spin_unlock_irq(&gt->sriov.vf.migration.lock);
> +
> +	xe_guc_submit_pause(&gt->uc.guc);
> +	ret |= xe_guc_submit_reset_block(&gt->uc.guc);

this |= seem unneeded

> +
> +	if (ret)
> +		xe_gt_sriov_info(gt, "migration recovery encountered ongoing reset\n");

is this the only possible reason? maybe worth to add %pe ?

> +}
> +
> +static size_t post_migration_scratch_size(struct xe_device *xe)
> +{
> +	return max(xe_lrc_reg_size(xe), LRC_WA_BB_SIZE);
> +}
> +
> +static int vf_post_migration_fixups(struct xe_gt *gt)
> +{
> +	s64 shift;
> +	void *buf;
> +	int err;
> +
> +	buf = kmalloc(post_migration_scratch_size(gt_to_xe(gt)), GFP_ATOMIC);
> +	if (!buf)
> +		return -ENOMEM;
> +
> +	err = xe_gt_sriov_vf_query_config(gt);
> +	if (err)
> +		goto out;
> +
> +	shift = xe_gt_sriov_vf_ggtt_shift(gt);
> +	if (shift) {
> +		xe_tile_sriov_vf_fixup_ggtt_nodes(gt_to_tile(gt), shift);
> +		xe_gt_sriov_vf_default_lrcs_hwsp_rebase(gt);
> +		err = xe_guc_contexts_hwsp_rebase(&gt->uc.guc, buf);
> +		if (err)
> +			goto out;
> +	}
> +
> +out:
> +	kfree(buf);
> +	return err;
> +}
> +
> +static void vf_post_migration_kickstart(struct xe_gt *gt)
> +{
> +	/*
> +	 * Make sure interrupts on the new HW are properly set. The GuC IRQ
> +	 * must be working at this point, since the recovery did started,
> +	 * but the rest was not enabled using the procedure from spec.
> +	 */
> +	xe_irq_resume(gt_to_xe(gt));
> +
> +	xe_guc_submit_reset_unblock(&gt->uc.guc);
> +	xe_guc_submit_unpause(&gt->uc.guc);
> +}
> +
> +static int vf_post_migration_notify_resfix_done(struct xe_gt *gt)
> +{
> +	bool skip_resfix = false;
> +
> +	spin_lock_irq(&gt->sriov.vf.migration.lock);
> +	if (gt->sriov.vf.migration.recovery_queued) {
> +		skip_resfix = true;
> +		xe_gt_sriov_dbg(gt, "another recovery imminent, skipped some notifications\n");
> +	} else {
> +		WRITE_ONCE(gt->sriov.vf.migration.recovery_inprogress, false);
> +	}
> +	spin_unlock_irq(&gt->sriov.vf.migration.lock);
> +
> +	return skip_resfix ? -EAGAIN : xe_gt_sriov_vf_notify_resfix_done(gt);

nit: this looks cleaner:

	if (skip_resfix)
		return -EAGAIN;

	return xe_gt_sriov_vf_notify_resfix_done(gt);

> +}
> +
> +static void vf_post_migration_recovery(struct xe_gt *gt)
> +{
> +	struct xe_device *xe = gt_to_xe(gt);
> +	int err;
> +
> +	xe_gt_sriov_dbg(gt, "migration recovery in progress\n");
> +
> +	xe_pm_runtime_get(xe);
> +	vf_post_migration_shutdown(gt);
> +
> +	if (!xe_sriov_vf_migration_supported(xe)) {
> +		xe_gt_sriov_err(gt, "migration is not supported\n");
> +		err = -ENOTRECOVERABLE;
> +		goto fail;
> +	}
> +
> +	err = vf_post_migration_fixups(gt);
> +	if (err)
> +		goto fail;
> +
> +	vf_post_migration_kickstart(gt);
> +	err = vf_post_migration_notify_resfix_done(gt);
> +	if (err && err != -EAGAIN)
> +		goto fail;
> +
> +	xe_pm_runtime_put(xe);
> +	xe_gt_sriov_notice(gt, "migration recovery ended\n");
> +	return;
> +fail:
> +	xe_pm_runtime_put(xe);
> +	xe_gt_sriov_err(gt, "migration recovery failed (%pe)\n", ERR_PTR(err));
> +	xe_device_declare_wedged(xe);
> +}
> +
> +static void migration_worker_func(struct work_struct *w)
> +{
> +	struct xe_gt *gt = container_of(w, struct xe_gt,
> +					sriov.vf.migration.worker);
> +
> +	vf_post_migration_recovery(gt);
> +}
> +
> +/**
> + * xe_gt_sriov_vf_migration_init_early() - VF post migration init early
> + * @gt: the &xe_gt
> + */
> +void xe_gt_sriov_vf_migration_init_early(struct xe_gt *gt)
> +{
> +	init_rwsem(&gt->sriov.vf.self_config.lock);
> +	spin_lock_init(&gt->sriov.vf.migration.lock);
> +	INIT_WORK(&gt->sriov.vf.migration.worker, migration_worker_func);
> +
> +	if (!xe_sriov_vf_migration_supported(gt_to_xe(gt)))
> +		xe_gt_sriov_info(gt, "migration not supported by this module version\n");

we likely don't want to repeat that message on every GT

> +}
> +
>  /**
>   * xe_gt_sriov_vf_recovery_inprogress() - VF post migration recovery in progress
>   * @gt: the &xe_gt
> diff --git a/drivers/gpu/drm/xe/xe_gt_sriov_vf.h b/drivers/gpu/drm/xe/xe_gt_sriov_vf.h
> index bb5f8eace19b..2ac6775b52f0 100644
> --- a/drivers/gpu/drm/xe/xe_gt_sriov_vf.h
> +++ b/drivers/gpu/drm/xe/xe_gt_sriov_vf.h
> @@ -21,10 +21,9 @@ void xe_gt_sriov_vf_guc_versions(struct xe_gt *gt,
>  int xe_gt_sriov_vf_query_config(struct xe_gt *gt);
>  int xe_gt_sriov_vf_connect(struct xe_gt *gt);
>  int xe_gt_sriov_vf_query_runtime(struct xe_gt *gt);
> -void xe_gt_sriov_vf_default_lrcs_hwsp_rebase(struct xe_gt *gt);
> -int xe_gt_sriov_vf_notify_resfix_done(struct xe_gt *gt);
>  void xe_gt_sriov_vf_migrated_event_handler(struct xe_gt *gt);
>  
> +void xe_gt_sriov_vf_migration_init_early(struct xe_gt *gt);
>  bool xe_gt_sriov_vf_recovery_inprogress(struct xe_gt *gt);
>  
>  u32 xe_gt_sriov_vf_gmdid(struct xe_gt *gt);
> diff --git a/drivers/gpu/drm/xe/xe_gt_sriov_vf_types.h b/drivers/gpu/drm/xe/xe_gt_sriov_vf_types.h
> index 7b10b8e1e10e..53680a2f188a 100644
> --- a/drivers/gpu/drm/xe/xe_gt_sriov_vf_types.h
> +++ b/drivers/gpu/drm/xe/xe_gt_sriov_vf_types.h
> @@ -8,6 +8,7 @@
>  
>  #include <linux/rwsem.h>
>  #include <linux/types.h>
> +#include <linux/workqueue.h>
>  #include "xe_uc_fw_types.h"
>  
>  /**
> @@ -53,6 +54,12 @@ struct xe_gt_sriov_vf_runtime {
>   * xe_gt_sriov_vf_migration - VF migration data.
>   */
>  struct xe_gt_sriov_vf_migration {
> +	/** @migration: VF migration recovery worker */
> +	struct work_struct worker;
> +	/** @lock: Protects recovery_queued */
> +	spinlock_t lock;
> +	/** @recovery_queued: VF post migration recovery in queued */
> +	bool recovery_queued;
>  	/** @recovery_inprogress: VF post migration recovery in progress */
>  	bool recovery_inprogress;
>  };
> diff --git a/drivers/gpu/drm/xe/xe_sriov_vf.c b/drivers/gpu/drm/xe/xe_sriov_vf.c
> index da064a1e7419..7d91553c4acc 100644
> --- a/drivers/gpu/drm/xe/xe_sriov_vf.c
> +++ b/drivers/gpu/drm/xe/xe_sriov_vf.c
> @@ -6,21 +6,12 @@
>  #include <drm/drm_debugfs.h>
>  #include <drm/drm_managed.h>
>  
> -#include "xe_assert.h"
> -#include "xe_device.h"
>  #include "xe_gt.h"
> -#include "xe_gt_sriov_printk.h"
>  #include "xe_gt_sriov_vf.h"
>  #include "xe_guc.h"
> -#include "xe_guc_submit.h"
> -#include "xe_irq.h"
> -#include "xe_lrc.h"
> -#include "xe_pm.h"
> -#include "xe_sriov.h"
>  #include "xe_sriov_printk.h"
>  #include "xe_sriov_vf.h"
>  #include "xe_sriov_vf_ccs.h"
> -#include "xe_tile_sriov_vf.h"
>  
>  /**
>   * DOC: VF restore procedure in PF KMD and VF KMD
> @@ -158,8 +149,6 @@ static void vf_disable_migration(struct xe_device *xe, const char *fmt, ...)
>  	xe->sriov.vf.migration.enabled = false;
>  }
>  
> -static void migration_worker_func(struct work_struct *w);
> -
>  static void vf_migration_init_early(struct xe_device *xe)
>  {
>  	/*
> @@ -184,8 +173,6 @@ static void vf_migration_init_early(struct xe_device *xe)
>  						    guc_version.major, guc_version.minor);
>  	}
>  
> -	INIT_WORK(&xe->sriov.vf.migration.worker, migration_worker_func);
> -
>  	xe->sriov.vf.migration.enabled = true;
>  	xe_sriov_dbg(xe, "migration support enabled\n");
>  }
> @@ -200,238 +187,11 @@ void xe_sriov_vf_init_early(struct xe_device *xe)
>  	unsigned int id;
>  
>  	for_each_gt(gt, xe, id)
> -		init_rwsem(&gt->sriov.vf.self_config.lock);
> +		xe_gt_sriov_vf_migration_init_early(gt);

still, this should be called from gt_init_early kind of functions

>  
>  	vf_migration_init_early(xe);
>  }
>  
> -/**
> - * vf_post_migration_shutdown - Stop the driver activities after VF migration.
> - * @xe: the &xe_device struct instance
> - *
> - * After this VM is migrated and assigned to a new VF, it is running on a new
> - * hardware, and therefore many hardware-dependent states and related structures
> - * require fixups. Without fixups, the hardware cannot do any work, and therefore
> - * all GPU pipelines are stalled.
> - * Stop some of kernel activities to make the fixup process faster.
> - */
> -static void vf_post_migration_shutdown(struct xe_device *xe)
> -{
> -	struct xe_gt *gt;
> -	unsigned int id;
> -	int ret = 0;
> -
> -	for_each_gt(gt, xe, id) {
> -		xe_guc_submit_pause(&gt->uc.guc);
> -		ret |= xe_guc_submit_reset_block(&gt->uc.guc);
> -	}
> -
> -	if (ret)
> -		drm_info(&xe->drm, "migration recovery encountered ongoing reset\n");
> -}
> -
> -/**
> - * vf_post_migration_kickstart - Re-start the driver activities under new hardware.
> - * @xe: the &xe_device struct instance
> - *
> - * After we have finished with all post-migration fixups, restart the driver
> - * activities to continue feeding the GPU with workloads.
> - */
> -static void vf_post_migration_kickstart(struct xe_device *xe)
> -{
> -	struct xe_gt *gt;
> -	unsigned int id;
> -
> -	/*
> -	 * Make sure interrupts on the new HW are properly set. The GuC IRQ
> -	 * must be working at this point, since the recovery did started,
> -	 * but the rest was not enabled using the procedure from spec.
> -	 */
> -	xe_irq_resume(xe);
> -
> -	for_each_gt(gt, xe, id) {
> -		xe_guc_submit_reset_unblock(&gt->uc.guc);
> -		xe_guc_submit_unpause(&gt->uc.guc);
> -	}
> -}
> -
> -static bool gt_vf_post_migration_needed(struct xe_gt *gt)
> -{
> -	return test_bit(gt->info.id, &gt_to_xe(gt)->sriov.vf.migration.gt_flags);
> -}
> -
> -/*
> - * Notify GuCs marked in flags about resource fixups apply finished.
> - * @xe: the &xe_device struct instance
> - * @gt_flags: flags marking to which GTs the notification shall be sent
> - */
> -static int vf_post_migration_notify_resfix_done(struct xe_device *xe, unsigned long gt_flags)
> -{
> -	struct xe_gt *gt;
> -	unsigned int id;
> -	int err = 0;
> -
> -	for_each_gt(gt, xe, id) {
> -		if (!test_bit(id, &gt_flags))
> -			continue;
> -		/* skip asking GuC for RESFIX exit if new recovery request arrived */
> -		if (gt_vf_post_migration_needed(gt))
> -			continue;
> -		err = xe_gt_sriov_vf_notify_resfix_done(gt);
> -		if (err)
> -			break;
> -		clear_bit(id, &gt_flags);
> -	}
> -
> -	if (gt_flags && !err)
> -		drm_dbg(&xe->drm, "another recovery imminent, skipped some notifications\n");
> -	return err;
> -}
> -
> -static int vf_get_next_migrated_gt_id(struct xe_device *xe)
> -{
> -	struct xe_gt *gt;
> -	unsigned int id;
> -
> -	for_each_gt(gt, xe, id) {
> -		if (test_and_clear_bit(id, &xe->sriov.vf.migration.gt_flags))
> -			return id;
> -	}
> -	return -1;
> -}
> -
> -static size_t post_migration_scratch_size(struct xe_device *xe)
> -{
> -	return max(xe_lrc_reg_size(xe), LRC_WA_BB_SIZE);
> -}
> -
> -/**
> - * Perform post-migration fixups on a single GT.
> - *
> - * After migration, GuC needs to be re-queried for VF configuration to check
> - * if it matches previous provisioning. Most of VF provisioning shall be the
> - * same, except GGTT range, since GGTT is not virtualized per-VF. If GGTT
> - * range has changed, we have to perform fixups - shift all GGTT references
> - * used anywhere within the driver. After the fixups in this function succeed,
> - * it is allowed to ask the GuC bound to this GT to continue normal operation.
> - *
> - * Returns: 0 if the operation completed successfully, or a negative error
> - * code otherwise.
> - */
> -static int gt_vf_post_migration_fixups(struct xe_gt *gt)
> -{
> -	s64 shift;
> -	void *buf;
> -	int err;
> -
> -	buf = kmalloc(post_migration_scratch_size(gt_to_xe(gt)), GFP_KERNEL);
> -	if (!buf)
> -		return -ENOMEM;
> -
> -	err = xe_gt_sriov_vf_query_config(gt);
> -	if (err)
> -		goto out;
> -
> -	shift = xe_gt_sriov_vf_ggtt_shift(gt);
> -	if (shift) {
> -		xe_tile_sriov_vf_fixup_ggtt_nodes(gt_to_tile(gt), shift);
> -		xe_gt_sriov_vf_default_lrcs_hwsp_rebase(gt);
> -		err = xe_guc_contexts_hwsp_rebase(&gt->uc.guc, buf);
> -		if (err)
> -			goto out;
> -	}
> -
> -out:
> -	kfree(buf);
> -	return err;
> -}
> -
> -static void vf_post_migration_recovery(struct xe_device *xe)
> -{
> -	unsigned long fixed_gts = 0;
> -	int id, err;
> -
> -	drm_dbg(&xe->drm, "migration recovery in progress\n");
> -	xe_pm_runtime_get(xe);
> -	vf_post_migration_shutdown(xe);
> -
> -	if (!xe_sriov_vf_migration_supported(xe)) {
> -		xe_sriov_err(xe, "migration is not supported\n");
> -		err = -ENOTRECOVERABLE;
> -		goto fail;
> -	}
> -
> -	while (id = vf_get_next_migrated_gt_id(xe), id >= 0) {
> -		struct xe_gt *gt = xe_device_get_gt(xe, id);
> -
> -		err = gt_vf_post_migration_fixups(gt);
> -		if (err)
> -			goto fail;
> -
> -		set_bit(id, &fixed_gts);
> -	}
> -
> -	vf_post_migration_kickstart(xe);
> -	err = vf_post_migration_notify_resfix_done(xe, fixed_gts);
> -	if (err)
> -		goto fail;
> -
> -	xe_pm_runtime_put(xe);
> -	drm_notice(&xe->drm, "migration recovery ended\n");
> -	return;
> -fail:
> -	xe_pm_runtime_put(xe);
> -	drm_err(&xe->drm, "migration recovery failed (%pe)\n", ERR_PTR(err));
> -	xe_device_declare_wedged(xe);
> -}
> -
> -static void migration_worker_func(struct work_struct *w)
> -{
> -	struct xe_device *xe = container_of(w, struct xe_device,
> -					    sriov.vf.migration.worker);
> -
> -	vf_post_migration_recovery(xe);
> -}
> -
> -/*
> - * Check if post-restore recovery is coming on any of GTs.
> - * @xe: the &xe_device struct instance
> - *
> - * Return: True if migration recovery worker will soon be running. Any worker currently
> - * executing does not affect the result.
> - */
> -static bool vf_ready_to_recovery_on_any_gts(struct xe_device *xe)
> -{
> -	struct xe_gt *gt;
> -	unsigned int id;
> -
> -	for_each_gt(gt, xe, id) {
> -		if (test_bit(id, &xe->sriov.vf.migration.gt_flags))
> -			return true;
> -	}
> -	return false;
> -}
> -
> -/**
> - * xe_sriov_vf_start_migration_recovery - Start VF migration recovery.
> - * @xe: the &xe_device to start recovery on
> - *
> - * This function shall be called only by VF.
> - */
> -void xe_sriov_vf_start_migration_recovery(struct xe_device *xe)
> -{
> -	bool started;
> -
> -	xe_assert(xe, IS_SRIOV_VF(xe));
> -
> -	if (!vf_ready_to_recovery_on_any_gts(xe))
> -		return;
> -
> -	started = queue_work(xe->sriov.wq, &xe->sriov.vf.migration.worker);
> -	drm_info(&xe->drm, "VF migration recovery %s\n", started ?
> -		 "scheduled" : "already in progress");
> -}
> -
>  /**
>   * xe_sriov_vf_init_late() - SR-IOV VF late initialization functions.
>   * @xe: the &xe_device to initialize
> diff --git a/drivers/gpu/drm/xe/xe_sriov_vf.h b/drivers/gpu/drm/xe/xe_sriov_vf.h
> index 9e752105ec2a..4df95266b261 100644
> --- a/drivers/gpu/drm/xe/xe_sriov_vf.h
> +++ b/drivers/gpu/drm/xe/xe_sriov_vf.h
> @@ -13,7 +13,6 @@ struct xe_device;
>  
>  void xe_sriov_vf_init_early(struct xe_device *xe);
>  int xe_sriov_vf_init_late(struct xe_device *xe);
> -void xe_sriov_vf_start_migration_recovery(struct xe_device *xe);
>  bool xe_sriov_vf_migration_supported(struct xe_device *xe);
>  void xe_sriov_vf_debugfs_register(struct xe_device *xe, struct dentry *root);
>  
> diff --git a/drivers/gpu/drm/xe/xe_sriov_vf_types.h b/drivers/gpu/drm/xe/xe_sriov_vf_types.h
> index 426cc5841958..6a0fd0f5463e 100644
> --- a/drivers/gpu/drm/xe/xe_sriov_vf_types.h
> +++ b/drivers/gpu/drm/xe/xe_sriov_vf_types.h
> @@ -33,10 +33,6 @@ struct xe_device_vf {
>  
>  	/** @migration: VF Migration state data */
>  	struct {
> -		/** @migration.worker: VF migration recovery worker */
> -		struct work_struct worker;
> -		/** @migration.gt_flags: Per-GT request flags for VF migration recovery */
> -		unsigned long gt_flags;
>  		/**
>  		 * @migration.enabled: flag indicating if migration support
>  		 * was enabled or not due to missing prerequisites


  reply	other threads:[~2025-09-24 10:49 UTC|newest]

Thread overview: 90+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2025-09-24  1:15 [PATCH v2 00/34] VF migration redesign Matthew Brost
2025-09-24  1:15 ` [PATCH v2 01/34] drm/xe/vf: Lock querying GGTT config during driver init Matthew Brost
2025-09-24  9:29   ` Michal Wajdeczko
2025-09-24 20:23     ` Matthew Brost
2025-09-30  0:42       ` Lis, Tomasz
2025-09-24  1:15 ` [PATCH v2 02/34] Revert "drm/xe/vf: Rebase exec queue parallel commands during migration recovery" Matthew Brost
2025-09-24  9:32   ` Michal Wajdeczko
2025-09-24 20:17     ` Matthew Brost
2025-09-24  1:15 ` [PATCH v2 03/34] Revert "drm/xe/vf: Post migration, repopulate ring area for pending request" Matthew Brost
2025-09-24  1:15 ` [PATCH v2 04/34] Revert "drm/xe/vf: Fixup CTB send buffer messages after migration" Matthew Brost
2025-09-24  1:15 ` [PATCH v2 05/34] drm/xe: Save off position in ring in which a job was programmed Matthew Brost
2025-09-24  1:15 ` [PATCH v2 06/34] drm/xe/guc: Track pending-enable source in submission state Matthew Brost
2025-09-24  1:15 ` [PATCH v2 07/34] drm/xe: Track LR jobs in DRM scheduler pending list Matthew Brost
2025-09-24  1:15 ` [PATCH v2 08/34] drm/xe: Don't change LRC ring head on job resubmission Matthew Brost
2025-09-24 15:14   ` Lis, Tomasz
2025-09-25 16:12     ` Matthew Brost
2025-09-24  1:15 ` [PATCH v2 09/34] drm/xe: Make LRC W/A scratch buffer usage consistent Matthew Brost
2025-09-24 14:23   ` Lis, Tomasz
2025-09-24 18:01   ` Lucas De Marchi
2025-09-25 20:25     ` Matthew Brost
2025-09-24  1:15 ` [PATCH v2 10/34] drm/xe/guc: Document GuC submission backend Matthew Brost
2025-09-24  9:35   ` Michal Wajdeczko
2025-09-24 20:20     ` Matthew Brost
2025-09-24  1:15 ` [PATCH v2 11/34] drm/xe/vf: Add xe_gt_sriov_vf_recovery_inprogress helper Matthew Brost
2025-09-24 10:14   ` Michal Wajdeczko
2025-09-24 19:39     ` Matthew Brost
2025-09-24 20:12       ` Michal Wajdeczko
2025-09-24 20:30         ` Matthew Brost
2025-09-24  1:15 ` [PATCH v2 12/34] drm/xe/vf: Make VF recovery run on per-GT worker Matthew Brost
2025-09-24 10:49   ` Michal Wajdeczko [this message]
2025-09-24 19:50     ` Matthew Brost
2025-09-24 20:21       ` Michal Wajdeczko
2025-09-24 20:35         ` Matthew Brost
2025-09-25 16:27           ` Lis, Tomasz
2025-09-25 16:56             ` Matthew Brost
2025-09-24  1:15 ` [PATCH v2 13/34] drm/xe/vf: Abort H2G sends during VF post-migration recovery Matthew Brost
2025-09-24 11:00   ` Michal Wajdeczko
2025-09-24 20:01     ` Matthew Brost
2025-09-24  1:15 ` [PATCH v2 14/34] drm/xe/vf: Remove memory allocations from VF post migration recovery Matthew Brost
2025-09-26  1:35   ` Lis, Tomasz
2025-09-26  1:43     ` Matthew Brost
2025-09-24  1:15 ` [PATCH v2 15/34] drm/xe/vf: Close multi-GT GGTT shift race Matthew Brost
2025-09-26  2:33   ` Lis, Tomasz
2025-09-26 19:09     ` Matthew Brost
2025-09-24  1:15 ` [PATCH v2 16/34] drm/xe/vf: Teardown VF post migration worker on driver unload Matthew Brost
2025-09-26 15:40   ` Lis, Tomasz
2025-09-26 19:13     ` Matthew Brost
2025-09-24  1:15 ` [PATCH v2 17/34] drm/xe/vf: Don't allow GT reset to be queued during VF post migration recovery Matthew Brost
2025-09-27  2:59   ` Lis, Tomasz
2025-09-27 22:33     ` Matthew Brost
2025-09-24  1:15 ` [PATCH v2 18/34] drm/xe/vf: Wakeup in GuC backend on " Matthew Brost
2025-09-25 19:06   ` Matthew Brost
2025-09-24  1:15 ` [PATCH v2 19/34] drm/xe/vf: Extra debug on GGTT shift Matthew Brost
2025-09-27  3:16   ` Lis, Tomasz
2025-09-27 11:06   ` Michal Wajdeczko
2025-09-27 22:56     ` Matthew Brost
2025-09-24  1:15 ` [PATCH v2 20/34] drm/xe/vf: Use GUC_HXG_TYPE_EVENT for GuC context register Matthew Brost
2025-09-24 11:15   ` Michal Wajdeczko
2025-09-24 20:16     ` Matthew Brost
2025-09-24  1:15 ` [PATCH v2 21/34] drm/xe/vf: Stop and flush CTs in VF post migration recovery Matthew Brost
2025-09-24 11:21   ` Michal Wajdeczko
2025-09-24 20:12     ` Matthew Brost
2025-09-24  1:15 ` [PATCH v2 22/34] drm/xe/vf: Reset TLB invalidations during " Matthew Brost
2025-09-27  3:43   ` Lis, Tomasz
2025-09-27 22:29     ` Matthew Brost
2025-09-24  1:15 ` [PATCH v2 23/34] drm/xe/vf: Kickstart after resfix in " Matthew Brost
2025-09-27 11:21   ` Lis, Tomasz
2025-09-24  1:15 ` [PATCH v2 24/34] drm/xe/vf: Start CTs before resfix " Matthew Brost
2025-09-24 11:50   ` Michal Wajdeczko
2025-09-24 20:10     ` Matthew Brost
2025-09-24  1:15 ` [PATCH v2 25/34] drm/xe/vf: Abort VF post migration recovery on failure Matthew Brost
2025-09-27 11:54   ` Lis, Tomasz
2025-09-27 22:38     ` Matthew Brost
2025-09-24  1:15 ` [PATCH v2 26/34] drm/xe/vf: Replay GuC submission state on pause / unpause Matthew Brost
2025-09-27 13:33   ` Lis, Tomasz
2025-09-27 23:11     ` Matthew Brost
2025-09-24  1:15 ` [PATCH v2 27/34] drm/xe: Move queue init before LRC creation Matthew Brost
2025-09-24  1:15 ` [PATCH v2 28/34] drm/xe/vf: Add debug prints for GuC replaying state during VF recovery Matthew Brost
2025-09-24  1:15 ` [PATCH v2 29/34] drm/xe/vf: Workaround for race condition in GuC firmware during VF pause Matthew Brost
2025-09-24  1:15 ` [PATCH v2 30/34] drm/xe: Use PPGTT addresses for TLB invalidation to avoid GGTT fixups Matthew Brost
2025-09-24  1:15 ` [PATCH v2 31/34] drm/xe/vf: Use primary GT ordered work queue on media GT on PTL VF Matthew Brost
2025-09-24  1:15 ` [PATCH v2 32/34] drm/xe/vf: Ensure media GT VF recovery runs after primary GT on PTL Matthew Brost
2025-09-24  1:16 ` [PATCH v2 33/34] drm/xe/vf: Rebase CCS save/restore BB GGTT addresses Matthew Brost
2025-09-24  4:04   ` K V P, Satyanarayana
2025-09-24  6:32     ` Matthew Brost
2025-09-24  6:36       ` K V P, Satyanarayana
2025-09-24  1:16 ` [PATCH v2 34/34] drm/xe/guc: Increase wait timeout to 2sec after BUSY reply from GuC Matthew Brost
2025-09-24  1:29 ` ✓ CI.KUnit: success for VF migration redesign (rev2) Patchwork
2025-09-24  2:14 ` ✗ Xe.CI.BAT: failure " Patchwork
2025-09-24  7:37 ` ✗ Xe.CI.Full: " Patchwork

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=55c5e870-6823-4fb3-80ab-0e6914d054d2@intel.com \
    --to=michal.wajdeczko@intel.com \
    --cc=intel-xe@lists.freedesktop.org \
    --cc=matthew.brost@intel.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox