* [PATCH 1/2] arm64: dts: ti: k3-j721e: Add CPSW9G nodes
2023-03-10 9:28 [PATCH 0/2] Add device-tree support for CPSW9G on J721E SoC Siddharth Vadapalli
@ 2023-03-10 9:28 ` Siddharth Vadapalli
2023-03-10 9:28 ` [PATCH 2/2] arm64: dts: ti: k3-j721e: Add overlay to enable CPSW9G ports in QSGMII mode Siddharth Vadapalli
1 sibling, 0 replies; 5+ messages in thread
From: Siddharth Vadapalli @ 2023-03-10 9:28 UTC (permalink / raw)
To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski,
krzysztof.kozlowski+dt
Cc: devicetree, linux-kernel, linux-arm-kernel, srk, s-vadapalli
TI's J721E SoC has a 9 port Ethernet Switch instance with 8 external
ports and 1 host port, referred to as CPSW9G.
Add device-tree nodes for CPSW9G and disable it by default. Device-tree
overlays will be used to enable it.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
---
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi | 107 ++++++++++++++++++++++
arch/arm64/boot/dts/ti/k3-j721e.dtsi | 1 +
2 files changed, 108 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
index c935622f0102..1ac7a47fc437 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
@@ -61,6 +61,13 @@ serdes_ln_ctrl: mux-controller@4080 {
<J721E_SERDES4_LANE2_EDP_LANE2>, <J721E_SERDES4_LANE3_EDP_LANE3>;
};
+ cpsw0_phy_gmii_sel: phy@4044 {
+ compatible = "ti,j721e-cpsw9g-phy-gmii-sel";
+ ti,qsgmii-main-ports = <2>, <2>;
+ reg = <0x4044 0x20>;
+ #phy-cells = <1>;
+ };
+
usb_serdes_mux: mux-controller@4000 {
compatible = "mmio-mux";
#mux-control-cells = <1>;
@@ -404,6 +411,106 @@ cpts@310d0000 {
};
};
+ cpsw0: ethernet@c000000 {
+ compatible = "ti,j721e-cpswxg-nuss";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ reg = <0x0 0xc000000 0x0 0x200000>;
+ reg-names = "cpsw_nuss";
+ ranges = <0x0 0x0 0x0 0x0c000000 0x0 0x200000>;
+ clocks = <&k3_clks 19 89>;
+ clock-names = "fck";
+ power-domains = <&k3_pds 19 TI_SCI_PD_EXCLUSIVE>;
+
+ dmas = <&main_udmap 0xca00>,
+ <&main_udmap 0xca01>,
+ <&main_udmap 0xca02>,
+ <&main_udmap 0xca03>,
+ <&main_udmap 0xca04>,
+ <&main_udmap 0xca05>,
+ <&main_udmap 0xca06>,
+ <&main_udmap 0xca07>,
+ <&main_udmap 0x4a00>;
+ dma-names = "tx0", "tx1", "tx2", "tx3",
+ "tx4", "tx5", "tx6", "tx7",
+ "rx";
+
+ status = "disabled";
+
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cpsw0_port1: port@1 {
+ reg = <1>;
+ ti,mac-only;
+ label = "port1";
+ };
+
+ cpsw0_port2: port@2 {
+ reg = <2>;
+ ti,mac-only;
+ label = "port2";
+ };
+
+ cpsw0_port3: port@3 {
+ reg = <3>;
+ ti,mac-only;
+ label = "port3";
+ };
+
+ cpsw0_port4: port@4 {
+ reg = <4>;
+ ti,mac-only;
+ label = "port4";
+ };
+
+ cpsw0_port5: port@5 {
+ reg = <5>;
+ ti,mac-only;
+ label = "port5";
+ };
+
+ cpsw0_port6: port@6 {
+ reg = <6>;
+ ti,mac-only;
+ label = "port6";
+ };
+
+ cpsw0_port7: port@7 {
+ reg = <7>;
+ ti,mac-only;
+ label = "port7";
+ };
+
+ cpsw0_port8: port@8 {
+ reg = <8>;
+ ti,mac-only;
+ label = "port8";
+ };
+ };
+
+ cpsw9g_mdio: mdio@f00 {
+ compatible = "ti,cpsw-mdio","ti,davinci_mdio";
+ reg = <0x0 0xf00 0x0 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&k3_clks 19 89>;
+ clock-names = "fck";
+ bus_freq = <1000000>;
+ };
+
+ cpts@3d000 {
+ compatible = "ti,j721e-cpts";
+ reg = <0x0 0x3d000 0x0 0x400>;
+ clocks = <&k3_clks 19 16>;
+ clock-names = "cpts";
+ interrupts-extended = <&gic500 GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "cpts";
+ ti,cpts-ext-ts-inputs = <4>;
+ ti,cpts-periodic-outputs = <2>;
+ };
+ };
+
main_crypto: crypto@4e00000 {
compatible = "ti,j721e-sa2ul";
reg = <0x0 0x4e00000 0x0 0x1200>;
diff --git a/arch/arm64/boot/dts/ti/k3-j721e.dtsi b/arch/arm64/boot/dts/ti/k3-j721e.dtsi
index 6975cae644d9..ddbaa06e21bd 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e.dtsi
@@ -135,6 +135,7 @@ cbass_main: bus@100000 {
<0x00 0x06000000 0x00 0x06000000 0x00 0x00400000>, /* USBSS0 */
<0x00 0x06400000 0x00 0x06400000 0x00 0x00400000>, /* USBSS1 */
<0x00 0x01000000 0x00 0x01000000 0x00 0x0af02400>, /* Most peripherals */
+ <0x00 0x0c000000 0x00 0x0c000000 0x00 0x0d000000>, /* CPSW9G */
<0x00 0x30000000 0x00 0x30000000 0x00 0x0c400000>, /* MAIN NAVSS */
<0x00 0x0d000000 0x00 0x0d000000 0x00 0x01800000>, /* PCIe Core*/
<0x00 0x0e000000 0x00 0x0e000000 0x00 0x01800000>, /* PCIe Core*/
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 5+ messages in thread* [PATCH 2/2] arm64: dts: ti: k3-j721e: Add overlay to enable CPSW9G ports in QSGMII mode
2023-03-10 9:28 [PATCH 0/2] Add device-tree support for CPSW9G on J721E SoC Siddharth Vadapalli
2023-03-10 9:28 ` [PATCH 1/2] arm64: dts: ti: k3-j721e: Add CPSW9G nodes Siddharth Vadapalli
@ 2023-03-10 9:28 ` Siddharth Vadapalli
2023-03-10 9:29 ` Krzysztof Kozlowski
1 sibling, 1 reply; 5+ messages in thread
From: Siddharth Vadapalli @ 2023-03-10 9:28 UTC (permalink / raw)
To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski,
krzysztof.kozlowski+dt
Cc: devicetree, linux-kernel, linux-arm-kernel, srk, s-vadapalli
The J7 Quad Port Add-On Ethernet Card for J721E Common-Proc-Board supports
QSGMII mode. Use the overlay to configure CPSW9G ports in QSGMII mode.
Add support to reset the PHY from kernel by using gpio-hog and gpio-reset.
Add aliases for CPSW9G ports to enable kernel to fetch MAC addresses
directly from U-Boot.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
---
arch/arm64/boot/dts/ti/Makefile | 4 +
.../dts/ti/k3-j721e-quad-port-eth-exp.dtso | 148 ++++++++++++++++++
2 files changed, 152 insertions(+)
create mode 100644 arch/arm64/boot/dts/ti/k3-j721e-quad-port-eth-exp.dtso
diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index 6acd12409d59..167bcd9b09b7 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -45,3 +45,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm.dtb
# Enable support for device-tree overlays
DTC_FLAGS_k3-am6548-iot2050-advanced-m2 += -@
+DTC_FLAGS_k3-j721e-common-proc-board += -@
+
+# Device-tree overlays
+dtb-$(CONFIG_ARCH_K3) += k3-j721e-quad-port-eth-exp.dtbo
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-quad-port-eth-exp.dtso b/arch/arm64/boot/dts/ti/k3-j721e-quad-port-eth-exp.dtso
new file mode 100644
index 000000000000..c63e1454614e
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-j721e-quad-port-eth-exp.dtso
@@ -0,0 +1,148 @@
+// SPDX-License-Identifier: GPL-2.0
+/**
+ * DT Overlay for CPSW9G in QSGMII mode using J7 Quad Port ETH EXP Add-On Ethernet Card with
+ * J721E board.
+ *
+ * Copyright (C) 2023 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mux/ti-serdes.h>
+#include <dt-bindings/pinctrl/k3.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/phy/phy-cadence.h>
+
+/ {
+ fragment@102 {
+ target-path = "/";
+ __overlay__ {
+ aliases {
+ ethernet1 = "/bus@100000/ethernet@c000000/ethernet-ports/port@1";
+ ethernet2 = "/bus@100000/ethernet@c000000/ethernet-ports/port@2";
+ ethernet3 = "/bus@100000/ethernet@c000000/ethernet-ports/port@3";
+ ethernet4 = "/bus@100000/ethernet@c000000/ethernet-ports/port@4";
+ };
+ };
+ };
+};
+
+&cpsw0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mdio_pins_default>;
+};
+
+&cpsw0_port1 {
+ phy-handle = <&cpsw9g_phy0>;
+ phy-mode = "qsgmii";
+ mac-address = [00 00 00 00 00 00];
+ phys = <&cpsw0_phy_gmii_sel 1>;
+};
+
+&cpsw0_port2 {
+ phy-handle = <&cpsw9g_phy1>;
+ phy-mode = "qsgmii";
+ mac-address = [00 00 00 00 00 00];
+ phys = <&cpsw0_phy_gmii_sel 2>;
+};
+
+&cpsw0_port3 {
+ phy-handle = <&cpsw9g_phy2>;
+ phy-mode = "qsgmii";
+ mac-address = [00 00 00 00 00 00];
+ phys = <&cpsw0_phy_gmii_sel 3>;
+};
+
+&cpsw0_port4 {
+ phy-handle = <&cpsw9g_phy3>;
+ phy-mode = "qsgmii";
+ mac-address = [00 00 00 00 00 00];
+ phys = <&cpsw0_phy_gmii_sel 4>;
+};
+
+&cpsw0_port5 {
+ status = "disabled";
+};
+
+&cpsw0_port6 {
+ status = "disabled";
+};
+
+&cpsw0_port7 {
+ status = "disabled";
+};
+
+&cpsw0_port8 {
+ status = "disabled";
+};
+
+&cpsw9g_mdio {
+ reset-gpios = <&exp2 17 GPIO_ACTIVE_LOW>;
+ reset-post-delay-us = <120000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpsw9g_phy0: ethernet-phy@17 {
+ reg = <17>;
+ };
+ cpsw9g_phy1: ethernet-phy@16 {
+ reg = <16>;
+ };
+ cpsw9g_phy2: ethernet-phy@18 {
+ reg = <18>;
+ };
+ cpsw9g_phy3: ethernet-phy@19 {
+ reg = <19>;
+ };
+};
+
+&exp2 {
+ qsgmii-line-hog {
+ gpio-hog;
+ gpios = <16 GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "qsgmii-pwrdn-line";
+ };
+};
+
+&main_pmx0 {
+ mdio_pins_default: mdio_pins_default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x1bc, PIN_OUTPUT, 0) /* (V24) MDIO0_MDC */
+ J721E_IOPAD(0x1b8, PIN_INPUT, 0) /* (V26) MDIO0_MDIO */
+ >;
+ };
+};
+
+&serdes_ln_ctrl {
+ idle-states = <J721E_SERDES0_LANE0_PCIE0_LANE0>, <J721E_SERDES0_LANE1_QSGMII_LANE2>,
+ <J721E_SERDES1_LANE0_PCIE1_LANE0>, <J721E_SERDES1_LANE1_PCIE1_LANE1>,
+ <J721E_SERDES2_LANE0_PCIE2_LANE0>, <J721E_SERDES2_LANE1_PCIE2_LANE1>,
+ <J721E_SERDES3_LANE0_USB3_0_SWAP>, <J721E_SERDES3_LANE1_USB3_0>,
+ <J721E_SERDES4_LANE0_EDP_LANE0>, <J721E_SERDES4_LANE1_EDP_LANE1>,
+ <J721E_SERDES4_LANE2_EDP_LANE2>, <J721E_SERDES4_LANE3_EDP_LANE3>;
+};
+
+&serdes_wiz0 {
+ status = "okay";
+};
+
+&serdes0 {
+ status = "okay";
+
+ assigned-clocks = <&serdes0 CDNS_SIERRA_PLL_CMNLC>, <&serdes0 CDNS_SIERRA_PLL_CMNLC1>;
+ assigned-clock-parents = <&wiz0_pll1_refclk>, <&wiz0_pll1_refclk>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ serdes0_qsgmii_link: phy@1 {
+ reg = <1>;
+ cdns,num-lanes = <1>;
+ #phy-cells = <0>;
+ cdns,phy-type = <PHY_TYPE_QSGMII>;
+ resets = <&serdes_wiz0 2>;
+ };
+};
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 5+ messages in thread