From: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
To: linux-aspeed@lists.ozlabs.org
Subject: [PATCH v3 13/14] ARM: dts: aspeed: yosemite4: support mux to cpld
Date: Mon, 11 Dec 2023 13:47:28 +0800 [thread overview]
Message-ID: <20231211054730.208588-14-Delphine_CC_Chiu@wiwynn.com> (raw)
In-Reply-To: <20231211054730.208588-1-Delphine_CC_Chiu@wiwynn.com>
Mux pca9544 to cpld was added on EVT HW schematic design,
so add dts setting for devices behind mux pca9544 to cpld
Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
.../aspeed/aspeed-bmc-facebook-yosemite4.dts | 64 ++++++++++++++-----
1 file changed, 49 insertions(+), 15 deletions(-)
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index c8e3a85b7a11..fdc33bffd467 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -36,6 +36,10 @@ aliases {
i2c31 = &imux31;
i2c32 = &imux32;
i2c33 = &imux33;
+ i2c34 = &imux34;
+ i2c35 = &imux35;
+ i2c36 = &imux36;
+ i2c37 = &imux37;
};
chosen {
@@ -951,24 +955,54 @@ &i2c12 {
status = "okay";
bus-frequency = <400000>;
- temperature-sensor at 48 {
- compatible = "ti,tmp75";
- reg = <0x48>;
- };
+ i2c-mux at 70 {
+ compatible = "nxp,pca9544";
+ i2c-mux-idle-disconnect;
+ reg = <0x70>;
- eeprom at 50 {
- compatible = "atmel,24c128";
- reg = <0x50>;
- };
+ imux34: i2c at 0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
- eeprom at 54 {
- compatible = "atmel,24c64";
- reg = <0x54>;
- };
+ temperature-sensor at 48 {
+ compatible = "ti,tmp75";
+ reg = <0x48>;
+ };
+
+ eeprom at 50 {
+ compatible = "atmel,24c128";
+ reg = <0x50>;
+ };
- rtc at 6f {
- compatible = "nuvoton,nct3018y";
- reg = <0x6f>;
+ eeprom at 54 {
+ compatible = "atmel,24c64";
+ reg = <0x54>;
+ };
+
+ rtc at 6f {
+ compatible = "nuvoton,nct3018y";
+ reg = <0x6f>;
+ };
+ };
+
+ imux35: i2c at 1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ imux36: i2c at 2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ imux37: i2c at 3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
};
};
--
2.25.1
next prev parent reply other threads:[~2023-12-11 5:47 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-12-11 5:47 [PATCH v3 00/14] Add i2c-mux and eeprom devices for Meta Yosemite 4 Delphine CC Chiu
2023-12-11 5:47 ` [PATCH v3 01/14] ARM: dts: aspeed: yosemite4: Revise i2c-mux devices Delphine CC Chiu
2023-12-11 5:47 ` [PATCH v3 02/14] ARM: dts: aspeed: yosemite4: Enable adc15 Delphine CC Chiu
2023-12-11 5:47 ` [PATCH v3 03/14] ARM: dts: aspeed: yosemite4: Enable spi-gpio setting Delphine CC Chiu
2023-12-11 5:47 ` [PATCH v3 04/14] ARM: dts: aspeed: yosemite4: Enable watchdog2 Delphine CC Chiu
2023-12-11 5:47 ` [PATCH v3 05/14] ARM: dts: aspeed: yosemite4: Revise quad mode to dual mode Delphine CC Chiu
2023-12-11 5:47 ` [PATCH v3 06/14] ARM: dts: aspeed: yosemite4: Revise power sensor adm1281 for schematic change Delphine CC Chiu
2023-12-11 5:47 ` [PATCH v3 07/14] ARM: dts: aspeed: yosemite4: Add gpio pca9506 Delphine CC Chiu
2023-12-11 5:47 ` [PATCH v3 08/14] ARM: dts: aspeed: yosemite4: Revise i2c11 and i2c12 schematic change Delphine CC Chiu
2023-12-13 7:20 ` Krzysztof Kozlowski
2023-12-11 5:47 ` [PATCH v3 09/14] ARM: dts: aspeed: yosemite4: Revise i2c14 and i2c15 " Delphine CC Chiu
2023-12-11 5:47 ` [PATCH v3 10/14] ARM: dts: aspeed: yosemite4: Initialize bmc gpio state Delphine CC Chiu
2023-12-11 5:47 ` [PATCH v3 11/14] ARM: dts: aspeed: yosemite4: Revise mx31790 fan tach config Delphine CC Chiu
2023-12-11 5:47 ` [PATCH v3 12/14] ARM: dts: aspeed: yosemite4: add mctp config for NIC Delphine CC Chiu
2023-12-11 5:47 ` Delphine CC Chiu [this message]
2023-12-11 5:47 ` [PATCH v3 14/14] ARM: dts: aspeed: yosemite4: Revise gpio name Delphine CC Chiu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20231211054730.208588-14-Delphine_CC_Chiu@wiwynn.com \
--to=delphine_cc_chiu@wiwynn.com \
--cc=linux-aspeed@lists.ozlabs.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox