[PATCH v9 00/26] Add i2c-mux and eeprom devices for Meta Yosemite 4

[PATCH v9 00/26] Add i2c-mux and eeprom devices for Meta Yosemite 4

[Delphine CC Chiu]

Changelog:
  - v9
    - add XDP710 support
    - add RTQ6056 support
    - add MP5990 support
  - v8
    - add fan led config
  - v7
    - Revise pca9506 i2c address
  - v6
    - Revise i2c duty-cycle for meeting 400khz spec
  - v5
    - Support medusa board adc sensors
    - support NIC eeprom
  - v4
    - Re-format gpio linename
    - Revise i2c device node names
    - Split patches by logic changes
  - v3
    - Correct patch for revising gpio name
  - v2
    - Revise mx31790 fan tach config
    - Add mctp config for NIC
    - Support mux to cpld
    - Revise gpio name
  - v1
    - Add gpio and eeprom behind i2c-mux
    - Remove redundant idle-state setting for i2c-mux
    - Enable adc 15, wdt2,spi gpio for yosemite4 use
    - Revise quad mode to dual mode to avoid WP pin influnece the SPI
    - Revise power sensor adm1281 for yosemite4 schematic change
    - Add gpio pca9506 I/O expander for yosemite4 use
    - remove space for adm1272 compatible
    - enable interrupt setting for pca9555
    - add eeprom for yosemite4 medusa board/BSM use
    - remove temperature sensor for yosemite4 schematic change
    - add power sensor for power module reading
    - Revise adc128d818 adc mode for yosemite4 schematic change
    - Revise ina233 for yosemite4 schematic change
    - Remove idle state setting for yosemite4 NIC connection
    - Initialize bmc gpio state
    - Revise mx31790 fan tach config
    - Add mctp config for NIC
    - Support mux to cpld
    - Revise gpio name

Delphine CC Chiu (26):
  ARM: dts: aspeed: yosemite4: Revise i2c-mux devices
  ARM: dts: aspeed: yosemite4: Enable adc15
  ARM: dts: aspeed: yosemite4: Enable spi-gpio setting
  ARM: dts: aspeed: yosemite4: Enable watchdog2
  ARM: dts: aspeed: yosemite4: Revise quad mode to dual mode
  ARM: dts: aspeed: yosemite4: Revise power sensor adm1281 for schematic
    change
  ARM: dts: aspeed: yosemite4: Add gpio pca9506
  ARM: dts: aspeed: yosemite4: Remove space for adm1272 compatible
  ARM: dts: aspeed: yosemite4: Enable interrupt setting for pca9555
  ARM: dts: aspeed: yosemite4: Add power sensor for power module reading
  ARM: dts: aspeed: yosemite4: Add eeprom for yosemite4 use
  ARM: dts: aspeed: yosemite4: Remove temperature sensor for yosemite4
    schematic change
  ARM: dts: aspeed: yosemite4: Revise adc128d818 adc mode for yosemite4
    schematic change
  ARM: dts: aspeed: yosemite4: Revise ina233 config for yosemite4
    schematic change
  ARM: dts: aspeed: yosemite4: Remove idle state setting for yosemite4
    NIC connection
  ARM: dts: aspeed: yosemite4: Initialize bmc gpio state
  ARM: dts: aspeed: yosemite4: Revise mx31790 fan tach config
  ARM: dts: aspeed: yosemite4: add mctp config for NIC
  ARM: dts: aspeed: yosemite4: support mux to cpld
  ARM: dts: aspeed: yosemite4: support medusa board adc sensors
  ARM: dts: aspeed: yosemite4: support NIC eeprom
  ARM: dts: aspeed: yosemite4: Revise i2c duty-cycle
  ARM: dts: aspeed: yosemite4: add fan led config
  ARM: dts: aspeed: yosemite4: add XDP710
  ARM: dts: aspeed: yosemite4: add RTQ6056 support
  ARM: dts: aspeed: yosemite4: add MP5990 support

 .../aspeed/aspeed-bmc-facebook-yosemite4.dts  | 1410 +++++++++++++++--
 1 file changed, 1306 insertions(+), 104 deletions(-)

-- 
2.25.1

[PATCH v9 01/26] ARM: dts: aspeed: yosemite4: Revise i2c-mux devices

[Delphine CC Chiu]

Revise Yosemite 4 devicetree for devices behind i2c-mux
- Add gpio and eeprom behind i2c-mux
- Remove redundant idle-state setting for i2c-mux

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../aspeed/aspeed-bmc-facebook-yosemite4.dts  | 381 ++++++++++++++++--
 1 file changed, 347 insertions(+), 34 deletions(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index 98477792aa00..66855efa0b4b 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -17,6 +17,25 @@ aliases {
 		serial6 = &uart7;
 		serial7 = &uart8;
 		serial8 = &uart9;
+
+		i2c16 = &imux16;
+		i2c17 = &imux17;
+		i2c18 = &imux18;
+		i2c19 = &imux19;
+		i2c20 = &imux20;
+		i2c21 = &imux21;
+		i2c22 = &imux22;
+		i2c23 = &imux23;
+		i2c24 = &imux24;
+		i2c25 = &imux25;
+		i2c26 = &imux26;
+		i2c27 = &imux27;
+		i2c28 = &imux28;
+		i2c29 = &imux29;
+		i2c30 = &imux30;
+		i2c31 = &imux31;
+		i2c32 = &imux32;
+		i2c33 = &imux33;
 	};
 
 	chosen {
@@ -259,9 +278,109 @@ &i2c8 {
 	bus-frequency = <400000>;
 	i2c-mux at 70 {
 		compatible = "nxp,pca9544";
-		idle-state = <0>;
 		i2c-mux-idle-disconnect;
 		reg = <0x70>;
+
+		imux16: i2c at 0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			gpio at 49 {
+				compatible = "nxp,pca9537";
+				reg = <0x49>;
+			};
+
+			eeprom at 50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+
+			eeprom at 51 {
+				compatible = "atmel,24c128";
+				reg = <0x51>;
+			};
+
+			eeprom at 54 {
+				compatible = "atmel,24c128";
+				reg = <0x54>;
+			};
+		};
+
+		imux17: i2c at 1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			gpio at 49 {
+				compatible = "nxp,pca9537";
+				reg = <0x49>;
+			};
+
+			eeprom at 50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+
+			eeprom at 51 {
+				compatible = "atmel,24c128";
+				reg = <0x51>;
+			};
+
+			eeprom at 54 {
+				compatible = "atmel,24c128";
+				reg = <0x54>;
+			};
+		};
+
+		imux18: i2c at 2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			gpio at 49 {
+				compatible = "nxp,pca9537";
+				reg = <0x49>;
+			};
+
+			eeprom at 50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+
+			eeprom at 51 {
+				compatible = "atmel,24c128";
+				reg = <0x51>;
+			};
+
+			eeprom at 54 {
+				compatible = "atmel,24c128";
+				reg = <0x54>;
+			};
+		};
+
+		imux19: i2c at 3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			gpio at 49 {
+				compatible = "nxp,pca9537";
+				reg = <0x49>;
+			};
+
+			eeprom at 50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+
+			eeprom at 51 {
+				compatible = "atmel,24c128";
+				reg = <0x51>;
+			};
+
+			eeprom at 54 {
+				compatible = "atmel,24c128";
+				reg = <0x54>;
+			};
+		};
 	};
 };
 
@@ -270,15 +389,174 @@ &i2c9 {
 	bus-frequency = <400000>;
 	i2c-mux at 71 {
 		compatible = "nxp,pca9544";
-		idle-state = <0>;
 		i2c-mux-idle-disconnect;
 		reg = <0x71>;
+
+		imux20: i2c at 0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			gpio at 49 {
+				compatible = "nxp,pca9537";
+				reg = <0x49>;
+			};
+
+			eeprom at 50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+
+			eeprom at 51 {
+				compatible = "atmel,24c128";
+				reg = <0x51>;
+			};
+
+			eeprom at 54 {
+				compatible = "atmel,24c128";
+				reg = <0x54>;
+			};
+		};
+
+		imux21: i2c at 1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			gpio at 49 {
+				compatible = "nxp,pca9537";
+				reg = <0x49>;
+			};
+
+			eeprom at 50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+
+			eeprom at 51 {
+				compatible = "atmel,24c128";
+				reg = <0x51>;
+			};
+
+			eeprom at 54 {
+				compatible = "atmel,24c128";
+				reg = <0x54>;
+			};
+		};
+
+		imux22: i2c at 2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			gpio at 49 {
+				compatible = "nxp,pca9537";
+				reg = <0x49>;
+			};
+
+			eeprom at 50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+
+			eeprom at 51 {
+				compatible = "atmel,24c128";
+				reg = <0x51>;
+			};
+
+			eeprom at 54 {
+				compatible = "atmel,24c128";
+				reg = <0x54>;
+			};
+		};
+
+		imux23: i2c at 3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			gpio at 49 {
+				compatible = "nxp,pca9537";
+				reg = <0x49>;
+			};
+
+			eeprom at 50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+
+			eeprom at 51 {
+				compatible = "atmel,24c128";
+				reg = <0x51>;
+			};
+
+			eeprom at 54 {
+				compatible = "atmel,24c128";
+				reg = <0x54>;
+			};
+		};
 	};
 };
 
 &i2c10 {
 	status = "okay";
 	bus-frequency = <400000>;
+	i2c-mux at 74 {
+		compatible = "nxp,pca9544";
+		i2c-mux-idle-disconnect;
+		reg = <0x74>;
+
+		imux28: i2c at 0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			gpio at 20 {
+				compatible = "nxp,pca9506";
+				reg = <0x20>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			gpio at 21 {
+				compatible = "nxp,pca9506";
+				reg = <0x21>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			gpio at 22 {
+				compatible = "nxp,pca9506";
+				reg = <0x22>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			gpio at 23 {
+				compatible = "nxp,pca9506";
+				reg = <0x23>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			gpio at 24 {
+				compatible = "nxp,pca9506";
+				reg = <0x24>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				gpio-line-names =
+				"","","","",
+				"NIC0-MAIN-PWR-EN","NIC1-MAIN-PWR-EN",
+				"NIC2-MAIN-PWR-EN","NIC3-MAIN-PWR-EN",
+				"","","","","","","","",
+				"","","","","","","","",
+				"","","","","","","","";
+			};
+		};
+
+		imux29: i2c at 1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+	};
 };
 
 &i2c11 {
@@ -440,16 +718,14 @@ eeprom at 51 {
 		reg = <0x51>;
 	};
 
-	i2c-mux at 71 {
-		compatible = "nxp,pca9846";
+	i2c-mux at 74 {
+		compatible = "nxp,pca9546";
 		#address-cells = <1>;
 		#size-cells = <0>;
-
-		idle-state = <0>;
 		i2c-mux-idle-disconnect;
-		reg = <0x71>;
+		reg = <0x74>;
 
-		i2c at 0 {
+		imux30: i2c at 0 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0>;
@@ -457,26 +733,26 @@ i2c at 0 {
 			adc at 1f {
 				compatible = "ti,adc128d818";
 				reg = <0x1f>;
-				ti,mode = /bits/ 8 <2>;
+				ti,mode = /bits/ 8 <1>;
 			};
 
 			pwm at 20{
-				compatible = "max31790";
+				compatible = "maxim,max31790";
+				pwm-as-tach = <4 5>;
 				reg = <0x20>;
-				#address-cells = <1>;
-				#size-cells = <0>;
 			};
 
 			gpio at 22{
 				compatible = "ti,tca6424";
 				reg = <0x22>;
+				gpio-controller;
+				#gpio-cells = <2>;
 			};
 
-			pwm at 23{
-				compatible = "max31790";
-				reg = <0x23>;
-				#address-cells = <1>;
-				#size-cells = <0>;
+			pwm at 2f{
+				compatible = "maxim,max31790";
+				pwm-as-tach = <4 5>;
+				reg = <0x2f>;
 			};
 
 			adc at 33 {
@@ -499,34 +775,34 @@ gpio at 61 {
 			};
 		};
 
-		i2c at 1 {
+		imux31: i2c at 1 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			reg = <0>;
+			reg = <1>;
 
 			adc at 1f {
 				compatible = "ti,adc128d818";
 				reg = <0x1f>;
-				ti,mode = /bits/ 8 <2>;
+				ti,mode = /bits/ 8 <1>;
 			};
 
 			pwm at 20{
-				compatible = "max31790";
+				compatible = "maxim,max31790";
+				pwm-as-tach = <4 5>;
 				reg = <0x20>;
-				#address-cells = <1>;
-				#size-cells = <0>;
 			};
 
 			gpio at 22{
 				compatible = "ti,tca6424";
 				reg = <0x22>;
+				gpio-controller;
+				#gpio-cells = <2>;
 			};
 
-			pwm at 23{
-				compatible = "max31790";
-				reg = <0x23>;
-				#address-cells = <1>;
-				#size-cells = <0>;
+			pwm at 2f{
+				compatible = "maxim,max31790";
+				pwm-as-tach = <4 5>;
+				reg = <0x2f>;
 			};
 
 			adc at 33 {
@@ -554,12 +830,10 @@ i2c-mux at 73 {
 		compatible = "nxp,pca9544";
 		#address-cells = <1>;
 		#size-cells = <0>;
-
-		idle-state = <0>;
 		i2c-mux-idle-disconnect;
 		reg = <0x73>;
 
-		i2c at 0 {
+		imux32: i2c at 0 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0>;
@@ -570,10 +844,10 @@ adc at 35 {
 			};
 		};
 
-		i2c at 1 {
+		imux33: i2c at 1 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			reg = <0>;
+			reg = <1>;
 
 			adc at 35 {
 				compatible = "maxim,max11617";
@@ -596,9 +870,48 @@ mctp at 10 {
 
 	i2c-mux at 72 {
 		compatible = "nxp,pca9544";
-		idle-state = <0>;
 		i2c-mux-idle-disconnect;
 		reg = <0x72>;
+
+		imux24: i2c at 0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			temperature-sensor at 1f {
+				compatible = "ti,tmp421";
+				reg = <0x1f>;
+			};
+		};
+
+		imux25: i2c at 1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			temperature-sensor at 1f {
+				compatible = "ti,tmp421";
+				reg = <0x1f>;
+			};
+		};
+
+		imux26: i2c at 2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			temperature-sensor at 1f {
+				compatible = "ti,tmp421";
+				reg = <0x1f>;
+			};
+		};
+
+		imux27: i2c at 3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			temperature-sensor at 1f {
+				compatible = "ti,tmp421";
+				reg = <0x1f>;
+			};
+		};
 	};
 };
 
-- 
2.25.1

[PATCH v9 02/26] ARM: dts: aspeed: yosemite4: Enable adc15

[Delphine CC Chiu]

Enable Yosemite 4 adc15 config

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index 66855efa0b4b..dd88be47d1c8 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -51,7 +51,7 @@ iio-hwmon {
 		compatible = "iio-hwmon";
 		io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
 				<&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
-				<&adc1 0>, <&adc1 1>;
+				<&adc1 0>, <&adc1 1>, <&adc1 7>;
 	};
 };
 
@@ -925,10 +925,10 @@ &pinctrl_adc4_default &pinctrl_adc5_default
 
 &adc1 {
 	status = "okay";
-	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default>;
+	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default>
+			&pinctrl_adc15_default>;
 };
 
-
 &ehci0 {
 	status = "okay";
 };
-- 
2.25.1

[PATCH v9 03/26] ARM: dts: aspeed: yosemite4: Enable spi-gpio setting

[Delphine CC Chiu]

enable spi-gpio setting for spi flash

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../aspeed/aspeed-bmc-facebook-yosemite4.dts   | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index dd88be47d1c8..effc2af636a4 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -53,6 +53,24 @@ iio-hwmon {
 				<&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
 				<&adc1 0>, <&adc1 1>, <&adc1 7>;
 	};
+
+	spi_gpio: spi-gpio {
+		compatible = "spi-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-sck = <&gpio0 ASPEED_GPIO(X, 3) GPIO_ACTIVE_HIGH>;
+		gpio-mosi = <&gpio0 ASPEED_GPIO(X, 4) GPIO_ACTIVE_HIGH>;
+		gpio-miso = <&gpio0 ASPEED_GPIO(X, 5) GPIO_ACTIVE_HIGH>;
+		num-chipselects = <1>;
+		cs-gpios = <&gpio0 ASPEED_GPIO(X, 0) GPIO_ACTIVE_LOW>;
+
+		tpmdev at 0 {
+			compatible = "tcg,tpm_tis-spi";
+			spi-max-frequency = <33000000>;
+			reg = <0>;
+		};
+	};
 };
 
 &uart1 {
-- 
2.25.1

[PATCH v9 04/26] ARM: dts: aspeed: yosemite4: Enable watchdog2

[Delphine CC Chiu]

enable watchdog2 setting

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index effc2af636a4..b0643e8aefee 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -120,6 +120,13 @@ &wdt1 {
 	aspeed,ext-pulse-duration = <256>;
 };
 
+&wdt2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdtrst2_default>;
+	aspeed,reset-type = "system";
+};
+
 &mac2 {
 	status = "okay";
 	pinctrl-names = "default";
-- 
2.25.1

[PATCH v9 05/26] ARM: dts: aspeed: yosemite4: Revise quad mode to dual mode

[Delphine CC Chiu]

Revise quad mode to dual mode to avoid WP pin influnece the SPI

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts | 8 +++++---
 1 file changed, 5 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index b0643e8aefee..a708e56b7ec3 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -149,15 +149,17 @@ flash at 0 {
 		status = "okay";
 		m25p,fast-read;
 		label = "bmc";
-		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <2>;
+		spi-rx-bus-width = <2>;
 		spi-max-frequency = <50000000>;
-#include "openbmc-flash-layout-64.dtsi"
+#include "openbmc-flash-layout-128.dtsi"
 	};
 	flash at 1 {
 		status = "okay";
 		m25p,fast-read;
 		label = "bmc2";
-		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <2>;
+		spi-rx-bus-width = <2>;
 		spi-max-frequency = <50000000>;
 	};
 };
-- 
2.25.1

[PATCH v9 06/26] ARM: dts: aspeed: yosemite4: Revise power sensor adm1281 for schematic change

[Delphine CC Chiu]

Revise power sensor adm1281 for yosemite4 schematic change

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../aspeed/aspeed-bmc-facebook-yosemite4.dts  | 24 ++++++++++++-------
 1 file changed, 16 insertions(+), 8 deletions(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index a708e56b7ec3..f0f714c7bc77 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -176,8 +176,9 @@ mctp at 10 {
 	};
 
 	power-sensor at 40 {
-		compatible = "adi,adm1278";
+		compatible = "adi,adm1281";
 		reg = <0x40>;
+		shunt-resistor-micro-ohms = <500>;
 	};
 };
 
@@ -193,8 +194,9 @@ mctp at 10 {
 	};
 
 	power-sensor at 40 {
-		compatible = "adi,adm1278";
+		compatible = "adi,adm1281";
 		reg = <0x40>;
+		shunt-resistor-micro-ohms = <500>;
 	};
 };
 
@@ -210,8 +212,9 @@ mctp at 10 {
 	};
 
 	power-sensor at 40 {
-		compatible = "adi,adm1278";
+		compatible = "adi,adm1281";
 		reg = <0x40>;
+		shunt-resistor-micro-ohms = <500>;
 	};
 };
 
@@ -227,8 +230,9 @@ mctp at 10 {
 	};
 
 	power-sensor at 40 {
-		compatible = "adi,adm1278";
+		compatible = "adi,adm1281";
 		reg = <0x40>;
+		shunt-resistor-micro-ohms = <500>;
 	};
 };
 
@@ -244,8 +248,9 @@ mctp at 10 {
 	};
 
 	power-sensor at 40 {
-		compatible = "adi,adm1278";
+		compatible = "adi,adm1281";
 		reg = <0x40>;
+		shunt-resistor-micro-ohms = <500>;
 	};
 };
 
@@ -261,8 +266,9 @@ mctp at 10 {
 	};
 
 	power-sensor at 40 {
-		compatible = "adi,adm1278";
+		compatible = "adi,adm1281";
 		reg = <0x40>;
+		shunt-resistor-micro-ohms = <500>;
 	};
 };
 
@@ -278,8 +284,9 @@ mctp at 10 {
 	};
 
 	power-sensor at 40 {
-		compatible = "adi,adm1278";
+		compatible = "adi,adm1281";
 		reg = <0x40>;
+		shunt-resistor-micro-ohms = <500>;
 	};
 };
 
@@ -295,8 +302,9 @@ mctp at 10 {
 	};
 
 	power-sensor at 40 {
-		compatible = "adi,adm1278";
+		compatible = "adi,adm1281";
 		reg = <0x40>;
+		shunt-resistor-micro-ohms = <500>;
 	};
 };
 
-- 
2.25.1

[PATCH v9 07/26] ARM: dts: aspeed: yosemite4: Add gpio pca9506

[Delphine CC Chiu]

Add gpio pca9506 I/O expander for yv4 use

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../aspeed/aspeed-bmc-facebook-yosemite4.dts  | 252 ++++++++++++++++++
 1 file changed, 252 insertions(+)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index f0f714c7bc77..33dcb2451ae3 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -175,6 +175,34 @@ mctp at 10 {
 		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
 	};
 
+	gpio at 21 {
+		compatible = "nxp,pca9506";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 22 {
+		compatible = "nxp,pca9506";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 23 {
+		compatible = "nxp,pca9506";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 24 {
+		compatible = "nxp,pca9506";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
 	power-sensor at 40 {
 		compatible = "adi,adm1281";
 		reg = <0x40>;
@@ -193,6 +221,34 @@ mctp at 10 {
 		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
 	};
 
+	gpio at 21 {
+		compatible = "nxp,pca9506";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 22 {
+		compatible = "nxp,pca9506";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 23 {
+		compatible = "nxp,pca9506";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 24 {
+		compatible = "nxp,pca9506";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
 	power-sensor at 40 {
 		compatible = "adi,adm1281";
 		reg = <0x40>;
@@ -211,6 +267,34 @@ mctp at 10 {
 		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
 	};
 
+	gpio at 21 {
+		compatible = "nxp,pca9506";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 22 {
+		compatible = "nxp,pca9506";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 23 {
+		compatible = "nxp,pca9506";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 24 {
+		compatible = "nxp,pca9506";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
 	power-sensor at 40 {
 		compatible = "adi,adm1281";
 		reg = <0x40>;
@@ -229,6 +313,34 @@ mctp at 10 {
 		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
 	};
 
+	gpio at 21 {
+		compatible = "nxp,pca9506";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 22 {
+		compatible = "nxp,pca9506";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 23 {
+		compatible = "nxp,pca9506";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 24 {
+		compatible = "nxp,pca9506";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
 	power-sensor at 40 {
 		compatible = "adi,adm1281";
 		reg = <0x40>;
@@ -247,6 +359,34 @@ mctp at 10 {
 		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
 	};
 
+	gpio at 21 {
+		compatible = "nxp,pca9506";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 22 {
+		compatible = "nxp,pca9506";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 23 {
+		compatible = "nxp,pca9506";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 24 {
+		compatible = "nxp,pca9506";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
 	power-sensor at 40 {
 		compatible = "adi,adm1281";
 		reg = <0x40>;
@@ -265,6 +405,34 @@ mctp at 10 {
 		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
 	};
 
+	gpio at 21 {
+		compatible = "nxp,pca9506";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 22 {
+		compatible = "nxp,pca9506";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 23 {
+		compatible = "nxp,pca9506";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 24 {
+		compatible = "nxp,pca9506";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
 	power-sensor at 40 {
 		compatible = "adi,adm1281";
 		reg = <0x40>;
@@ -283,6 +451,34 @@ mctp at 10 {
 		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
 	};
 
+	gpio at 21 {
+		compatible = "nxp,pca9506";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 22 {
+		compatible = "nxp,pca9506";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 23 {
+		compatible = "nxp,pca9506";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 24 {
+		compatible = "nxp,pca9506";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
 	power-sensor at 40 {
 		compatible = "adi,adm1281";
 		reg = <0x40>;
@@ -301,6 +497,34 @@ mctp at 10 {
 		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
 	};
 
+	gpio at 21 {
+		compatible = "nxp,pca9506";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 22 {
+		compatible = "nxp,pca9506";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 23 {
+		compatible = "nxp,pca9506";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 24 {
+		compatible = "nxp,pca9506";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
 	power-sensor at 40 {
 		compatible = "adi,adm1281";
 		reg = <0x40>;
@@ -690,6 +914,34 @@ ipmb at 10 {
 		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
 		i2c-protocol;
 	};
+
+	gpio at 20 {
+		compatible = "nxp,pca9506";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 21 {
+		compatible = "nxp,pca9506";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 22 {
+		compatible = "nxp,pca9506";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 23 {
+		compatible = "nxp,pca9506";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
 };
 
 &i2c14 {
-- 
2.25.1

[PATCH v9 08/26] ARM: dts: aspeed: yosemite4: Remove space for adm1272 compatible

[Delphine CC Chiu]

Remove space for adm1272 compatible

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index 33dcb2451ae3..ee11b3b8e81f 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -821,12 +821,12 @@ imux29: i2c at 1 {
 &i2c11 {
 	status = "okay";
 	power-sensor at 10 {
-		compatible = "adi, adm1272";
+		compatible = "adi,adm1272";
 		reg = <0x10>;
 	};
 
 	power-sensor at 12 {
-		compatible = "adi, adm1272";
+		compatible = "adi,adm1272";
 		reg = <0x12>;
 	};
 
-- 
2.25.1

[PATCH v9 09/26] ARM: dts: aspeed: yosemite4: Enable interrupt setting for pca9555

[Delphine CC Chiu]

Enable interrupt setting for pca9555

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../aspeed/aspeed-bmc-facebook-yosemite4.dts  | 56 +++++++++++++++++--
 1 file changed, 52 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index ee11b3b8e81f..92733a8ecf0b 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -832,30 +832,78 @@ power-sensor at 12 {
 
 	gpio at 20 {
 		compatible = "nxp,pca9555";
-		reg = <0x20>;
+		pinctrl-names = "default";
 		gpio-controller;
 		#gpio-cells = <2>;
+		reg = <0x20>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <98 IRQ_TYPE_LEVEL_LOW>;
+		gpio-line-names =
+		"P48V-OCP-GPIO1","P48V-OCP-GPIO2",
+		"P48V-OCP-GPIO3","FAN-BOARD-0-REVISION-0-R",
+		"FAN-BOARD-0-REVISION-1-R","FAN-BOARD-1-REVISION-0-R",
+		"FAN-BOARD-1-REVISION-1-R","RST-MUX-R-N",
+		"RST-LED-CONTROL-FAN-BOARD-0-N","RST-LED-CONTROL-FAN-BOARD-1-N",
+		"RST-IOEXP-FAN-BOARD-0-N","RST-IOEXP-FAN-BOARD-1-N",
+		"PWRGD-LOAD-SWITCH-FAN-BOARD-0-R","PWRGD-LOAD-SWITCH-FAN-BOARD-1-R",
+		"","";
 	};
 
 	gpio at 21 {
 		compatible = "nxp,pca9555";
-		reg = <0x21>;
+		pinctrl-names = "default";
 		gpio-controller;
 		#gpio-cells = <2>;
+		reg = <0x21>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <98 IRQ_TYPE_LEVEL_LOW>;
+		gpio-line-names =
+		"HSC-OCP-SLOT-ODD-GPIO1","HSC-OCP-SLOT-ODD-GPIO2",
+		"HSC-OCP-SLOT-ODD-GPIO3","HSC-OCP-SLOT-EVEN-GPIO1",
+		"HSC-OCP-SLOT-EVEN-GPIO2","HSC-OCP-SLOT-EVEN-GPIO3",
+		"ADC-TYPE-0-R","ADC-TYPE-1-R",
+		"MEDUSA-BOARD-REV-0","MEDUSA-BOARD-REV-1",
+		"MEDUSA-BOARD-REV-2","MEDUSA-BOARD-TYPE",
+		"DELTA-MODULE-TYPE","P12V-HSC-TYPE",
+		"","";
 	};
 
 	gpio at 22 {
 		compatible = "nxp,pca9555";
-		reg = <0x22>;
+		pinctrl-names = "default";
 		gpio-controller;
 		#gpio-cells = <2>;
+		reg = <0x22>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <98 IRQ_TYPE_LEVEL_LOW>;
+		gpio-line-names =
+		"CARD-TYPE-SLOT1","CARD-TYPE-SLOT2",
+		"CARD-TYPE-SLOT3","CARD-TYPE-SLOT4",
+		"CARD-TYPE-SLOT5","CARD-TYPE-SLOT6",
+		"CARD-TYPE-SLOT7","CARD-TYPE-SLOT8",
+		"OC-P48V-HSC-0-N","FLT-P48V-HSC-0-N",
+		"OC-P48V-HSC-1-N","FLT-P48V-HSC-1-N",
+		"EN-P48V-AUX-0","EN-P48V-AUX-1",
+		"PWRGD-P12V-AUX-0","PWRGD-P12V-AUX-1";
 	};
 
 	gpio at 23 {
 		compatible = "nxp,pca9555";
-		reg = <0x23>;
+		pinctrl-names = "default";
 		gpio-controller;
 		#gpio-cells = <2>;
+		reg = <0x23>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <98 IRQ_TYPE_LEVEL_LOW>;
+		gpio-line-names =
+		"HSC1-ALERT1-R-N","HSC2-ALERT1-R-N",
+		"HSC3-ALERT1-R-N","HSC4-ALERT1-R-N",
+		"HSC5-ALERT1-R-N","HSC6-ALERT1-R-N",
+		"HSC7-ALERT1-R-N","HSC8-ALERT1-R-N",
+		"HSC1-ALERT2-R-N","HSC2-ALERT2-R-N",
+		"HSC3-ALERT2-R-N","HSC4-ALERT2-R-N",
+		"HSC5-ALERT2-R-N","HSC6-ALERT2-R-N",
+		"HSC7-ALERT2-R-N","HSC8-ALERT2-R-N";
 	};
 
 	temperature-sensor at 48 {
-- 
2.25.1

[PATCH v9 10/26] ARM: dts: aspeed: yosemite4: Add power sensor for power module reading

[Delphine CC Chiu]

Add power sensor for power module reading

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../aspeed/aspeed-bmc-facebook-yosemite4.dts  | 25 +++++++++++++++++++
 1 file changed, 25 insertions(+)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index 92733a8ecf0b..2ac872878acd 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -906,6 +906,11 @@ gpio at 23 {
 		"HSC7-ALERT2-R-N","HSC8-ALERT2-R-N";
 	};
 
+	power-sensor at 40 {
+		compatible = "mps,mp5023";
+		reg = <0x40>;
+	};
+
 	temperature-sensor at 48 {
 		compatible = "ti,tmp75";
 		reg = <0x48>;
@@ -930,6 +935,26 @@ eeprom at 54 {
 		compatible = "atmel,24c256";
 		reg = <0x54>;
 	};
+
+	power-sensor at 62 {
+		compatible = "pmbus";
+		reg = <0x62>;
+	};
+
+	power-sensor at 64 {
+		compatible = "pmbus";
+		reg = <0x64>;
+	};
+
+	power-sensor at 65 {
+		compatible = "pmbus";
+		reg = <0x65>;
+	};
+
+	power-sensor at 68 {
+		compatible = "pmbus";
+		reg = <0x68>;
+	};
 };
 
 &i2c12 {
-- 
2.25.1

[PATCH v9 11/26] ARM: dts: aspeed: yosemite4: Add eeprom for yosemite4 use

[Delphine CC Chiu]

Add eeprom for yosemite4 use

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts | 7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index 2ac872878acd..9a14f0220cf6 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -932,7 +932,7 @@ temperature-sensor at 4b {
 	};
 
 	eeprom at 54 {
-		compatible = "atmel,24c256";
+		compatible = "atmel,24c128";
 		reg = <0x54>;
 	};
 
@@ -971,6 +971,11 @@ eeprom at 50 {
 		reg = <0x50>;
 	};
 
+	eeprom at 54 {
+		compatible = "atmel,24c64";
+		reg = <0x54>;
+	};
+
 	rtc at 6f {
 		compatible = "nuvoton,nct3018y";
 		reg = <0x6f>;
-- 
2.25.1

[PATCH v9 12/26] ARM: dts: aspeed: yosemite4: Remove temperature sensor for yosemite4 schematic change

[Delphine CC Chiu]

Remove temperature sensor for yosemite4 schematic change

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts  | 10 ----------
 1 file changed, 10 deletions(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index 9a14f0220cf6..8f3bbdd1bbc5 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -921,16 +921,6 @@ temperature-sensor at 49 {
 		reg = <0x49>;
 	};
 
-	temperature-sensor at 4a {
-		compatible = "ti,tmp75";
-		reg = <0x4a>;
-	};
-
-	temperature-sensor at 4b {
-		compatible = "ti,tmp75";
-		reg = <0x4b>;
-	};
-
 	eeprom at 54 {
 		compatible = "atmel,24c128";
 		reg = <0x54>;
-- 
2.25.1

[PATCH v9 13/26] ARM: dts: aspeed: yosemite4: Revise adc128d818 adc mode for yosemite4 schematic change

[Delphine CC Chiu]

Revise adc128d818 adc mode for yosemite4 schematic change

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts  | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index 8f3bbdd1bbc5..0c7d85ff4360 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -1018,19 +1018,19 @@ &i2c14 {
 	adc at 1d {
 		compatible = "ti,adc128d818";
 		reg = <0x1d>;
-		ti,mode = /bits/ 8 <2>;
+		ti,mode = /bits/ 8 <1>;
 	};
 
-	adc at 35 {
+	adc at 36 {
 		compatible = "ti,adc128d818";
-		reg = <0x35>;
-		ti,mode = /bits/ 8 <2>;
+		reg = <0x36>;
+		ti,mode = /bits/ 8 <1>;
 	};
 
 	adc at 37 {
 		compatible = "ti,adc128d818";
 		reg = <0x37>;
-		ti,mode = /bits/ 8 <2>;
+		ti,mode = /bits/ 8 <1>;
 	};
 
 	power-sensor at 40 {
-- 
2.25.1

[PATCH v9 14/26] ARM: dts: aspeed: yosemite4: Revise ina233 config for yosemite4 schematic change

[Delphine CC Chiu]

Revise ina233 config for yosemite4 schematic change

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../aspeed/aspeed-bmc-facebook-yosemite4.dts  | 20 ++++++++++++++-----
 1 file changed, 15 insertions(+), 5 deletions(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index 0c7d85ff4360..67e3c787d675 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -1034,28 +1034,38 @@ adc at 37 {
 	};
 
 	power-sensor at 40 {
-		compatible = "ti,ina230";
+		compatible = "ti,ina233";
 		reg = <0x40>;
+		resistor-calibration = /bits/ 16 <0x0a00>;
+		current-lsb= /bits/ 16 <0x0001>;
 	};
 
 	power-sensor at 41 {
-		compatible = "ti,ina230";
+		compatible = "ti,ina233";
 		reg = <0x41>;
+		resistor-calibration = /bits/ 16 <0x0a00>;
+		current-lsb= /bits/ 16 <0x0001>;
 	};
 
 	power-sensor at 42 {
-		compatible = "ti,ina230";
+		compatible = "ti,ina233";
 		reg = <0x42>;
+		resistor-calibration = /bits/ 16 <0x0a00>;
+		current-lsb= /bits/ 16 <0x0001>;
 	};
 
 	power-sensor at 43 {
-		compatible = "ti,ina230";
+		compatible = "ti,ina233";
 		reg = <0x43>;
+		resistor-calibration = /bits/ 16 <0x0a00>;
+		current-lsb= /bits/ 16 <0x0001>;
 	};
 
 	power-sensor at 44 {
-		compatible = "ti,ina230";
+		compatible = "ti,ina233";
 		reg = <0x44>;
+		resistor-calibration = /bits/ 16 <0x0a00>;
+		current-lsb= /bits/ 16 <0x0001>;
 	};
 
 	temperature-sensor at 4e {
-- 
2.25.1

[PATCH v9 15/26] ARM: dts: aspeed: yosemite4: Remove idle state setting for yosemite4 NIC connection

[Delphine CC Chiu]

Remove idle state setting for yosemite4 NIC connection

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts | 1 -
 1 file changed, 1 deletion(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index 67e3c787d675..8b23b012d6f5 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -1235,7 +1235,6 @@ mctp at 10 {
 
 	i2c-mux at 72 {
 		compatible = "nxp,pca9544";
-		i2c-mux-idle-disconnect;
 		reg = <0x72>;
 
 		imux24: i2c at 0 {
-- 
2.25.1

[PATCH v9 16/26] ARM: dts: aspeed: yosemite4: Initialize bmc gpio state

[Delphine CC Chiu]

Initialize bmc gpio state

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../aspeed/aspeed-bmc-facebook-yosemite4.dts  | 234 ++++++++++++++++++
 1 file changed, 234 insertions(+)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index 8b23b012d6f5..3baf1df11a81 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -1304,3 +1304,237 @@ &ehci1 {
 &uhci {
 	status = "okay";
 };
+
+&sgpiom0 {
+	status = "okay";
+	ngpios = <128>;
+	bus-frequency = <48000>;
+};
+
+&pinctrl {
+	pinctrl_gpio0_unbiased: gpio0_unbiased {
+		/* GPIOB0, GPIOB1 */
+		pins = "J26", "K23";
+		bias-disable;
+	};
+	pinctrl_gpio2_unbiased: gpio2_unbiased {
+		/* GPIOI5, GPIOI6, GPIOI7,
+		   GPIOL6 */
+		pins = "E16", "B16", "A15", "B14";
+		bias-disable;
+	};
+	pinctrl_gpio3_unbiased: gpio3_unbiased {
+		/* GPIOM2, GPIOM3, GPIOM4, GPIOM5,
+		   GPION0, GPION1, GPION2, GPION3, GPION5,
+		   GPIOO0, GPIOO1, GPIOO2, GPIOO3,
+		   GPIOP0, GPIOP1, GPIOP2, GPIOP3, GPIOP4, GPIOP5, GPIOP6 */
+		pins = "A12", "E14", "B12", "C12", "P25", "N23", "N25", "N24", "M23", "AD26", "AD22", "AD23", "AD24", "AB22", "W24", "AA23", "AA24", "W23", "AB23", "AB24";
+		bias-disable;
+	};
+	pinctrl_gpio4_unbiased: gpio4_unbiased {
+		/* GPIOR0, GPIOR1, GPIOR2, GPIOR3, GPIOR4, GPIOR5, GPIOR6, GPIOR7
+		   GPIOS0, GPIOS1, GPIOS2, GPIOS3, GPIOS5, GPIOS6, GPIOS7 */
+		pins = "V25", "U24", "V24", "V26", "U25", "T23", "W26", "U26", "R23", "T25", "T26", "R24", "P24", "P23", "T24";
+		bias-disable;
+	};
+	pinctrl_gpio5_unbiased: gpio5_unbiased {
+		/* GPIOV0, GPIOV1, GPIOV2, GPIOV3, GPIOV4, GPIOV5, GPIOV6, GPIOV7
+		   GPIOX1, GPIOX2 */
+		pins = "AB15", "AF14", "AD14", "AC15", "AE15", "AE14", "AD15", "AF15", "AA9", "AC9";
+		bias-disable;
+	};
+	pinctrl_gpio6_unbiased: gpio6_unbiased {
+		/* GPIOY2, GPIOY5, GPIOY6
+		   GPIOZ0, GPIOZ1, GPIOZ3, GPIOZ4 */
+		pins = "AE11", "AF12", "AC12", "AC10", "AD10", "AB11", "AC11";
+		bias-disable;
+	};
+};
+
+&gpio0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpiu2_default &pinctrl_gpiu3_default
+		     &pinctrl_gpiu4_default &pinctrl_gpiu6_default
+		     &pinctrl_gpio0_unbiased &pinctrl_gpio2_unbiased
+		     &pinctrl_gpio3_unbiased &pinctrl_gpio4_unbiased
+		     &pinctrl_gpio5_unbiased &pinctrl_gpio6_unbiased>;
+	gpio-line-names =
+	/*A0-A7*/       "","","","","","","","",
+	/*B0-B7*/       "FLT-HSC-SERVER-SLOT8-N","AC-ON-OFF-BTN-CPLD-SLOT5-N",
+			"PWRGD-SLOT1-STBY","PWRGD-SLOT2-STBY",
+			"PWRGD-SLOT3-STBY","PWRGD-SLOT4-STBY","","",
+	/*C0-C7*/       "","","","","FM-NIC0-WAKE-N",
+			"FM-NIC1-WAKE-N","","RST-PCIE-SLOT2-N",
+	/*D0-D7*/       "","","","","","","","",
+	/*E0-E7*/       "PRSNT-NIC1-N","PRSNT-NIC2-N","","RST-PCIE-SLOT1-N",
+			"","","","",
+	/*F0-F7*/       "FM-RESBTN-SLOT1-BMC-N","FM-RESBTN-SLOT2-BMC-N",
+			"FM-RESBTN-SLOT3-BMC-N","FM-RESBTN-SLOT4-BMC-N",
+			"PRSNT-SB-SLOT1-N","PRSNT-SB-SLOT2-N",
+			"PRSNT-SB-SLOT3-N","PRSNT-SB-SLOT4-N",
+	/*G0-G7*/       "","","","","","","","",
+	/*H0-H7*/       "","","","","","","","",
+	/*I0-I7*/       "","","","","","ALT-MEDUSA-ADC-N",
+			"ALT-SMB-BMC-CPLD2-N",
+			"INT-SPIDER-ADC-R-N",
+	/*J0-J7*/       "","","","","","","","",
+	/*K0-K7*/       "","","","","","","","",
+	/*L0-L7*/       "","","","","","","ALT-MEDUSA-P12V-EFUSE-N","",
+	/*M0-M7*/       "EN-NIC0-POWER-BMC-R","EN-NIC1-POWER-BMC-R",
+			"INT-MEDUSA-IOEXP-TEMP-N","PRSNT-NIC3-N",
+			"INT-SMB-BMC-SLOT1-4-BMC-N",
+			"AC-ON-OFF-BTN-CPLD-SLOT6-N","","",
+	/*N0-N7*/       "FLT-HSC-SERVER-SLOT1-N","FLT-HSC-SERVER-SLOT2-N",
+			"FLT-HSC-SERVER-SLOT3-N","FLT-HSC-SERVER-SLOT4-N",
+			"FM-BMC-READY-R2","RST-SMB-NIC0-R-N","","",
+	/*O0-O7*/       "AC-ON-OFF-BTN-CPLD-SLOT8-N","RST-SMB-NIC1-R-N",
+			"RST-SMB-NIC2-R-N","RST-SMB-NIC3-R-N",
+			"","","","",
+	/*P0-P7*/       "ALT-SMB-BMC-CPLD1-N","'BTN-BMC-R2-N",
+			"EN-P3V-BAT-SCALED-R","PWRGD-P5V-USB-BMC",
+			"FM-BMC-RTCRST-R","RST-USB-HUB-R-N",
+			"FLAG-P5V-USB-BMC-N","",
+	/*Q0-Q7*/       "AC-ON-OFF-BTN-CPLD-SLOT1-N","AC-ON-OFF-BTN-CPLD-SLOT2-N",
+			"AC-ON-OFF-BTN-CPLD-SLOT3-N","AC-ON-OFF-BTN-CPLD-SLOT4-N",
+			"PRSNT-SB-SLOT5-N","PRSNT-SB-SLOT6-N",
+			"PRSNT-SB-SLOT7-N","PRSNT-SB-SLOT8-N",
+	/*R0-R7*/       "AC-ON-OFF-BTN-CPLD-SLOT7-N","INT-SMB-BMC-SLOT5-8-BMC-N",
+			"FM-PWRBRK-NIC-BMC-R2","RST-PCIE-SLOT4-N",
+			"RST-PCIE-SLOT5-N","RST-PCIE-SLOT6-N",
+			"RST-PCIE-SLOT7-N","RST-PCIE-SLOT8-N",
+	/*S0-S7*/       "FM-NIC2-WAKE-N","FM-NIC3-WAKE-N",
+			"EN-NIC3-POWER-BMC-R","SEL-BMC-JTAG-MUX-R",
+			"","ALT-P12V-AUX-N","FAST-PROCHOT-N",
+			"SPI-WP-DISABLE-STATUS-R-N",
+	/*T0-T7*/       "","","","","","","","",
+	/*U0-U7*/       "","","RST-PCIE-SLOT3-N","",
+			"","PRSNT-NIC0-N","","",
+	/*V0-V7*/       "FM-RESBTN-SLOT5-BMC-N","FM-RESBTN-SLOT6-BMC-N",
+			"FM-RESBTN-SLOT7-BMC-N","FM-RESBTN-SLOT8-BMC-N",
+			"","","","",
+	/*W0-W7*/       "PRSNT-TPM-BMC-N","PRSNT-OCP-DEBUG-BMC-N","ALT-TEMP-BMC-N","ALT-RTC-BMC-N",
+			"","","","",
+	/*X0-X7*/       "","LT-HSC-SERVER-SLOT6-N","FLT-HSC-SERVER-SLOT7-N","","","",
+			"PWRGD-SLOT5-STBY","PWRGD-SLOT6-STBY",
+	/*Y0-Y7*/       "","","SPI-LOCK-REQ-BMC-N","PWRGD-SLOT7-STBY",
+			"","","EN-NIC2-POWER-BMC-R","",
+	/*Z0-Z7*/       "EN-P5V-USB-CPLD-R","'FLT-HSC-SERVER-SLOT5-N",
+			"PWRGD-SLOT8-STBY","","","","","";
+
+	pin_gpio_b4 {
+		gpios = <ASPEED_GPIO(B, 4) GPIO_ACTIVE_HIGH>;
+		input;
+	};
+	pin_gpio_b5 {
+		gpios = <ASPEED_GPIO(B, 5) GPIO_ACTIVE_HIGH>;
+		input;
+	};
+	pin_gpio_f0 {
+		gpios = <ASPEED_GPIO(F, 0) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_f1 {
+		gpios = <ASPEED_GPIO(F, 1) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_f2 {
+		gpios = <ASPEED_GPIO(F, 2) GPIO_ACTIVE_LOW>;
+		input;
+		};
+	pin_gpio_f3 {
+		gpios = <ASPEED_GPIO(F, 3) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_f4 {
+		gpios = <ASPEED_GPIO(F, 4) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_f5 {
+		gpios = <ASPEED_GPIO(F, 5) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_f6 {
+		gpios = <ASPEED_GPIO(F, 6) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_f7 {
+		gpios = <ASPEED_GPIO(F, 7) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_l6 {
+		gpios = <ASPEED_GPIO(L, 6) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_l7 {
+		gpios = <ASPEED_GPIO(L, 7) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_s0 {
+		gpios = <ASPEED_GPIO(S, 0) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_s1 {
+		gpios = <ASPEED_GPIO(S, 1) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_v0 {
+		gpios = <ASPEED_GPIO(V, 0) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_v1 {
+		gpios = <ASPEED_GPIO(V, 1) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_v2 {
+		gpios = <ASPEED_GPIO(V, 2) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_v3 {
+		gpios = <ASPEED_GPIO(V, 3) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_w0 {
+		gpios = <ASPEED_GPIO(W, 0) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_w1 {
+		gpios = <ASPEED_GPIO(W, 1) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_w2 {
+		gpios = <ASPEED_GPIO(W, 2) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_w3 {
+		gpios = <ASPEED_GPIO(W, 3) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_w4 {
+		gpios = <ASPEED_GPIO(W, 4) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_w5 {
+		gpios = <ASPEED_GPIO(W, 5) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_w6 {
+		gpios = <ASPEED_GPIO(W, 6) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_w7 {
+		gpios = <ASPEED_GPIO(W, 7) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_z3 {
+		gpios = <ASPEED_GPIO(Z, 3) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_z4 {
+		gpios = <ASPEED_GPIO(Z, 4) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_z5 {
+		gpios = <ASPEED_GPIO(Z, 5) GPIO_ACTIVE_LOW>;
+		input;
+	};
+};
-- 
2.25.1

[PATCH v9 17/26] ARM: dts: aspeed: yosemite4: Revise mx31790 fan tach config

[Delphine CC Chiu]

Revise fan tach config for max31790 driver change

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../aspeed/aspeed-bmc-facebook-yosemite4.dts  | 48 +++++++++++++++++--
 1 file changed, 44 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index 3baf1df11a81..59615a6958ec 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -1103,8 +1103,18 @@ adc at 1f {
 
 			pwm at 20{
 				compatible = "maxim,max31790";
-				pwm-as-tach = <4 5>;
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <0x20>;
+				channel at 4 {
+					reg = <4>;
+					sensor-type = "TACH";
+				};
+
+				channel at 5 {
+					reg = <5>;
+					sensor-type = "TACH";
+				};
 			};
 
 			gpio at 22{
@@ -1116,8 +1126,18 @@ gpio at 22{
 
 			pwm at 2f{
 				compatible = "maxim,max31790";
-				pwm-as-tach = <4 5>;
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <0x2f>;
+				channel at 4 {
+					reg = <4>;
+					sensor-type = "TACH";
+				};
+
+				channel at 5 {
+					reg = <5>;
+					sensor-type = "TACH";
+				};
 			};
 
 			adc at 33 {
@@ -1153,8 +1173,18 @@ adc at 1f {
 
 			pwm at 20{
 				compatible = "maxim,max31790";
-				pwm-as-tach = <4 5>;
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <0x20>;
+				channel at 4 {
+					reg = <4>;
+					sensor-type = "TACH";
+				};
+
+				channel at 5 {
+					reg = <5>;
+					sensor-type = "TACH";
+				};
 			};
 
 			gpio at 22{
@@ -1166,8 +1196,18 @@ gpio at 22{
 
 			pwm at 2f{
 				compatible = "maxim,max31790";
-				pwm-as-tach = <4 5>;
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <0x2f>;
+				channel at 4 {
+					reg = <4>;
+					sensor-type = "TACH";
+				};
+
+				channel at 5 {
+					reg = <5>;
+					sensor-type = "TACH";
+				};
 			};
 
 			adc at 33 {
-- 
2.25.1

[PATCH v9 18/26] ARM: dts: aspeed: yosemite4: add mctp config for NIC

[Delphine CC Chiu]

add mctp config for NIC

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../aspeed/aspeed-bmc-facebook-yosemite4.dts  | 24 +++++++++++++++++++
 1 file changed, 24 insertions(+)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index 59615a6958ec..83c9d76f5a11 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -1281,40 +1281,64 @@ imux24: i2c at 0 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0>;
+			mctp-controller;
 			temperature-sensor at 1f {
 				compatible = "ti,tmp421";
 				reg = <0x1f>;
 			};
+
+			temperature-sensor at 3c {
+				compatible = "smsc,emc1403";
+				reg = <0x3c>;
+			};
 		};
 
 		imux25: i2c at 1 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <1>;
+			mctp-controller;
 			temperature-sensor at 1f {
 				compatible = "ti,tmp421";
 				reg = <0x1f>;
 			};
+
+			temperature-sensor at 3c {
+				compatible = "smsc,emc1403";
+				reg = <0x3c>;
+			};
 		};
 
 		imux26: i2c at 2 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <2>;
+			mctp-controller;
 			temperature-sensor at 1f {
 				compatible = "ti,tmp421";
 				reg = <0x1f>;
 			};
+
+			temperature-sensor at 3c {
+				compatible = "smsc,emc1403";
+				reg = <0x3c>;
+			};
 		};
 
 		imux27: i2c at 3 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <3>;
+			mctp-controller;
 			temperature-sensor at 1f {
 				compatible = "ti,tmp421";
 				reg = <0x1f>;
 			};
+
+			temperature-sensor at 3c {
+				compatible = "smsc,emc1403";
+				reg = <0x3c>;
+			};
 		};
 	};
 };
-- 
2.25.1

[PATCH v9 19/26] ARM: dts: aspeed: yosemite4: support mux to cpld

[Delphine CC Chiu]

Mux pca9544 to cpld was added on EVT HW schematic design,
so add dts setting for devices behind mux pca9544 to cpld

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../aspeed/aspeed-bmc-facebook-yosemite4.dts  | 64 ++++++++++++++-----
 1 file changed, 49 insertions(+), 15 deletions(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index 83c9d76f5a11..f4e37187bd5b 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -36,6 +36,10 @@ aliases {
 		i2c31 = &imux31;
 		i2c32 = &imux32;
 		i2c33 = &imux33;
+		i2c34 = &imux34;
+		i2c35 = &imux35;
+		i2c36 = &imux36;
+		i2c37 = &imux37;
 	};
 
 	chosen {
@@ -951,24 +955,54 @@ &i2c12 {
 	status = "okay";
 	bus-frequency = <400000>;
 
-	temperature-sensor at 48 {
-		compatible = "ti,tmp75";
-		reg = <0x48>;
-	};
+	i2c-mux at 70 {
+		compatible = "nxp,pca9544";
+		i2c-mux-idle-disconnect;
+		reg = <0x70>;
 
-	eeprom at 50 {
-		compatible = "atmel,24c128";
-		reg = <0x50>;
-	};
+		imux34: i2c at 0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
 
-	eeprom at 54 {
-		compatible = "atmel,24c64";
-		reg = <0x54>;
-	};
+			temperature-sensor at 48 {
+				compatible = "ti,tmp75";
+				reg = <0x48>;
+			};
+
+			eeprom at 50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
 
-	rtc at 6f {
-		compatible = "nuvoton,nct3018y";
-		reg = <0x6f>;
+			eeprom at 54 {
+				compatible = "atmel,24c64";
+				reg = <0x54>;
+			};
+
+			rtc at 6f {
+				compatible = "nuvoton,nct3018y";
+				reg = <0x6f>;
+			};
+		};
+
+		imux35: i2c at 1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		imux36: i2c at 2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		imux37: i2c at 3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
 	};
 };
 
-- 
2.25.1

[PATCH v9 20/26] ARM: dts: aspeed: yosemite4: support medusa board adc sensors

[Delphine CC Chiu]

Add ina233/ina28 support for medusa board adc sensors

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../dts/aspeed/aspeed-bmc-facebook-yosemite4.dts    | 13 +++++++++++++
 1 file changed, 13 insertions(+)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index f4e37187bd5b..bacaa2208734 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -915,6 +915,19 @@ power-sensor at 40 {
 		reg = <0x40>;
 	};
 
+	power-sensor at 41 {
+			compatible = "ti,ina233";
+			resistor-calibration = /bits/ 16 <0x0a00>;
+			current-lsb= /bits/ 16 <0x0001>;
+			reg = <0x41>;
+	};
+
+	power-sensor at 44 {
+			compatible = "ti,ina238";
+			shunt-resistor = <1000>;
+			reg = <0x44>;
+	};
+
 	temperature-sensor at 48 {
 		compatible = "ti,tmp75";
 		reg = <0x48>;
-- 
2.25.1

[PATCH v9 21/26] ARM: dts: aspeed: yosemite4: support NIC eeprom

[Delphine CC Chiu]

Add NIC eeprom devicetree config

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../aspeed/aspeed-bmc-facebook-yosemite4.dts  | 20 +++++++++++++++++++
 1 file changed, 20 insertions(+)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index bacaa2208734..62dfe935cbcd 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -1338,6 +1338,11 @@ temperature-sensor at 3c {
 				compatible = "smsc,emc1403";
 				reg = <0x3c>;
 			};
+
+			eeprom at 50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
 		};
 
 		imux25: i2c at 1 {
@@ -1354,6 +1359,11 @@ temperature-sensor at 3c {
 				compatible = "smsc,emc1403";
 				reg = <0x3c>;
 			};
+
+			eeprom at 50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
 		};
 
 		imux26: i2c at 2 {
@@ -1370,6 +1380,11 @@ temperature-sensor at 3c {
 				compatible = "smsc,emc1403";
 				reg = <0x3c>;
 			};
+
+			eeprom at 50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
 		};
 
 		imux27: i2c at 3 {
@@ -1386,6 +1401,11 @@ temperature-sensor at 3c {
 				compatible = "smsc,emc1403";
 				reg = <0x3c>;
 			};
+
+			eeprom at 50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
 		};
 	};
 };
-- 
2.25.1

[PATCH v9 22/26] ARM: dts: aspeed: yosemite4: Revise i2c duty-cycle

[Delphine CC Chiu]

Revise duty cycle SMB11 and SMB16 to high: 40%, low: 60%,
to meet 400kHz-i2c clock low time spec (> 1.3 us) from EE request

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index 62dfe935cbcd..21ca22281ef8 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -761,6 +761,7 @@ eeprom at 54 {
 &i2c10 {
 	status = "okay";
 	bus-frequency = <400000>;
+	i2c-clk-high-min-percent = <40>;
 	i2c-mux at 74 {
 		compatible = "nxp,pca9544";
 		i2c-mux-idle-disconnect;
@@ -1314,6 +1315,7 @@ &i2c15 {
 	mctp-controller;
 	multi-master;
 	bus-frequency = <400000>;
+	i2c-clk-high-min-percent = <40>;
 
 	mctp at 10 {
 		compatible = "mctp-i2c-controller";
-- 
2.25.1

[PATCH v9 23/26] ARM: dts: aspeed: yosemite4: add fan led config

[Delphine CC Chiu]

Set fan led config in yosemite4 DTS.

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../aspeed/aspeed-bmc-facebook-yosemite4.dts  | 152 +++++++++++++++++-
 1 file changed, 150 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index 21ca22281ef8..2cbb210ed53e 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -75,6 +75,154 @@ tpmdev at 0 {
 			reg = <0>;
 		};
 	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		fan0_blue {
+			retain-state-shutdown;
+			default-state = "on";
+			gpios = <&led_gpio0 4 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan0_amber {
+			retain-state-shutdown;
+			default-state = "off";
+			gpios = <&led_gpio0 5 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan1_blue {
+			retain-state-shutdown;
+			default-state = "on";
+			gpios = <&led_gpio0 10 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan1_amber {
+			retain-state-shutdown;
+			default-state = "off";
+			gpios = <&led_gpio0 11 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan2_blue {
+			retain-state-shutdown;
+			default-state = "on";
+			gpios = <&led_gpio1 4 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan2_amber {
+			retain-state-shutdown;
+			default-state = "off";
+			gpios = <&led_gpio1 5 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan3_blue {
+			retain-state-shutdown;
+			default-state = "on";
+			gpios = <&led_gpio1 10 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan3_amber {
+			retain-state-shutdown;
+			default-state = "off";
+			gpios = <&led_gpio1 11 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan4_blue {
+			retain-state-shutdown;
+			default-state = "on";
+			gpios = <&led_gpio0 2 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan4_amber {
+			retain-state-shutdown;
+			default-state = "off";
+			gpios = <&led_gpio0 3 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan5_blue {
+			retain-state-shutdown;
+			default-state = "on";
+			gpios = <&led_gpio0 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan5_amber {
+			retain-state-shutdown;
+			default-state = "off";
+			gpios = <&led_gpio0 9 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan6_blue {
+			retain-state-shutdown;
+			default-state = "on";
+			gpios = <&led_gpio1 2 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan6_amber {
+			retain-state-shutdown;
+			default-state = "off";
+			gpios = <&led_gpio1 3 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan7_blue {
+			retain-state-shutdown;
+			default-state = "on";
+			gpios = <&led_gpio1 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan7_amber {
+			retain-state-shutdown;
+			default-state = "off";
+			gpios = <&led_gpio1 9 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan8_blue {
+			retain-state-shutdown;
+			default-state = "on";
+			gpios = <&led_gpio0 0 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan8_amber {
+			retain-state-shutdown;
+			default-state = "off";
+			gpios = <&led_gpio0 1 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan9_blue {
+			retain-state-shutdown;
+			default-state = "on";
+			gpios = <&led_gpio0 6 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan9_amber {
+			retain-state-shutdown;
+			default-state = "off";
+			gpios = <&led_gpio0 7 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan10_blue {
+			retain-state-shutdown;
+			default-state = "on";
+			gpios = <&led_gpio1 0 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan10_amber {
+			retain-state-shutdown;
+			default-state = "off";
+			gpios = <&led_gpio1 1 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan11_blue {
+			retain-state-shutdown;
+			default-state = "on";
+			gpios = <&led_gpio1 6 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan11_amber {
+			retain-state-shutdown;
+			default-state = "off";
+			gpios = <&led_gpio1 7 GPIO_ACTIVE_HIGH>;
+		};
+	};
 };
 
 &uart1 {
@@ -1198,7 +1346,7 @@ eeprom at 52 {
 				reg = <0x52>;
 			};
 
-			gpio at 61 {
+			led_gpio0: gpio at 61 {
 				compatible = "nxp,pca9552";
 				reg = <0x61>;
 				#address-cells = <1>;
@@ -1268,7 +1416,7 @@ eeprom at 52 {
 				reg = <0x52>;
 			};
 
-			gpio at 61 {
+			led_gpio1: gpio at 61 {
 				compatible = "nxp,pca9552";
 				reg = <0x61>;
 				#address-cells = <1>;
-- 
2.25.1

[PATCH v9 24/26] ARM: dts: aspeed: yosemite4: add XDP710

[Delphine CC Chiu]

Add XDP710 in yosemite4 DTS.

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts  | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index 2cbb210ed53e..05f109687ee2 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -978,11 +978,21 @@ power-sensor at 10 {
 		reg = <0x10>;
 	};
 
+	power-sensor at 11 {
+		compatible = "infineon,xdp710";
+		reg = <0x11>;
+	};
+
 	power-sensor at 12 {
 		compatible = "adi,adm1272";
 		reg = <0x12>;
 	};
 
+	power-sensor at 13 {
+		compatible = "infineon,xdp710";
+		reg = <0x13>;
+	};
+
 	gpio at 20 {
 		compatible = "nxp,pca9555";
 		pinctrl-names = "default";
-- 
2.25.1

[PATCH v9 25/26] ARM: dts: aspeed: yosemite4: add RTQ6056 support

[Delphine CC Chiu]

Add RTQ6056 (spider board 3rd source) support in yosemite4 DTS.

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts  | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index 05f109687ee2..b0eb38f9aa7e 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -1240,35 +1240,35 @@ adc at 37 {
 	};
 
 	power-sensor at 40 {
-		compatible = "ti,ina233";
+		compatible = "ti,ina233", "richtek,rtq6056";
 		reg = <0x40>;
 		resistor-calibration = /bits/ 16 <0x0a00>;
 		current-lsb= /bits/ 16 <0x0001>;
 	};
 
 	power-sensor at 41 {
-		compatible = "ti,ina233";
+		compatible = "ti,ina233", "richtek,rtq6056";
 		reg = <0x41>;
 		resistor-calibration = /bits/ 16 <0x0a00>;
 		current-lsb= /bits/ 16 <0x0001>;
 	};
 
 	power-sensor at 42 {
-		compatible = "ti,ina233";
+		compatible = "ti,ina233", "richtek,rtq6056";
 		reg = <0x42>;
 		resistor-calibration = /bits/ 16 <0x0a00>;
 		current-lsb= /bits/ 16 <0x0001>;
 	};
 
 	power-sensor at 43 {
-		compatible = "ti,ina233";
+		compatible = "ti,ina233", "richtek,rtq6056";
 		reg = <0x43>;
 		resistor-calibration = /bits/ 16 <0x0a00>;
 		current-lsb= /bits/ 16 <0x0001>;
 	};
 
 	power-sensor at 44 {
-		compatible = "ti,ina233";
+		compatible = "ti,ina233", "richtek,rtq6056";
 		reg = <0x44>;
 		resistor-calibration = /bits/ 16 <0x0a00>;
 		current-lsb= /bits/ 16 <0x0001>;
-- 
2.25.1

[PATCH v9 26/26] ARM: dts: aspeed: yosemite4: add MP5990 support

[Delphine CC Chiu]

Add MP5990 in yosemite4 DTS.

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../dts/aspeed/aspeed-bmc-facebook-yosemite4.dts | 16 ++++++++--------
 1 file changed, 8 insertions(+), 8 deletions(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index b0eb38f9aa7e..7ad080e3f432 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -356,7 +356,7 @@ gpio at 24 {
 	};
 
 	power-sensor at 40 {
-		compatible = "adi,adm1281";
+		compatible = "adi,adm1281", "mps,mp5990";
 		reg = <0x40>;
 		shunt-resistor-micro-ohms = <500>;
 	};
@@ -402,7 +402,7 @@ gpio at 24 {
 	};
 
 	power-sensor at 40 {
-		compatible = "adi,adm1281";
+		compatible = "adi,adm1281", "mps,mp5990";
 		reg = <0x40>;
 		shunt-resistor-micro-ohms = <500>;
 	};
@@ -448,7 +448,7 @@ gpio at 24 {
 	};
 
 	power-sensor at 40 {
-		compatible = "adi,adm1281";
+		compatible = "adi,adm1281", "mps,mp5990";
 		reg = <0x40>;
 		shunt-resistor-micro-ohms = <500>;
 	};
@@ -494,7 +494,7 @@ gpio at 24 {
 	};
 
 	power-sensor at 40 {
-		compatible = "adi,adm1281";
+		compatible = "adi,adm1281", "mps,mp5990";
 		reg = <0x40>;
 		shunt-resistor-micro-ohms = <500>;
 	};
@@ -540,7 +540,7 @@ gpio at 24 {
 	};
 
 	power-sensor at 40 {
-		compatible = "adi,adm1281";
+		compatible = "adi,adm1281", "mps,mp5990";
 		reg = <0x40>;
 		shunt-resistor-micro-ohms = <500>;
 	};
@@ -586,7 +586,7 @@ gpio at 24 {
 	};
 
 	power-sensor at 40 {
-		compatible = "adi,adm1281";
+		compatible = "adi,adm1281", "mps,mp5990";
 		reg = <0x40>;
 		shunt-resistor-micro-ohms = <500>;
 	};
@@ -632,7 +632,7 @@ gpio at 24 {
 	};
 
 	power-sensor at 40 {
-		compatible = "adi,adm1281";
+		compatible = "adi,adm1281", "mps,mp5990";
 		reg = <0x40>;
 		shunt-resistor-micro-ohms = <500>;
 	};
@@ -678,7 +678,7 @@ gpio at 24 {
 	};
 
 	power-sensor at 40 {
-		compatible = "adi,adm1281";
+		compatible = "adi,adm1281", "mps,mp5990";
 		reg = <0x40>;
 		shunt-resistor-micro-ohms = <500>;
 	};
-- 
2.25.1

[PATCH v9 03/26] ARM: dts: aspeed: yosemite4: Enable spi-gpio setting

[Rob Herring]

On Wed, Jun 26, 2024 at 3:08?AM Delphine CC Chiu
<Delphine_CC_Chiu@wiwynn.com> wrote:
>
> enable spi-gpio setting for spi flash

I don't see a flash device added.

>
> Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
> ---
>  .../aspeed/aspeed-bmc-facebook-yosemite4.dts   | 18 ++++++++++++++++++
>  1 file changed, 18 insertions(+)
>
> diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
> index dd88be47d1c8..effc2af636a4 100644
> --- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
> +++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
> @@ -53,6 +53,24 @@ iio-hwmon {
>                                 <&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
>                                 <&adc1 0>, <&adc1 1>, <&adc1 7>;
>         };
> +
> +       spi_gpio: spi-gpio {
> +               compatible = "spi-gpio";
> +               #address-cells = <1>;
> +               #size-cells = <0>;
> +
> +               gpio-sck = <&gpio0 ASPEED_GPIO(X, 3) GPIO_ACTIVE_HIGH>;
> +               gpio-mosi = <&gpio0 ASPEED_GPIO(X, 4) GPIO_ACTIVE_HIGH>;
> +               gpio-miso = <&gpio0 ASPEED_GPIO(X, 5) GPIO_ACTIVE_HIGH>;

Not the right properties for GPIOS. Run 'make dtbs_check' on your DT files.

> +               num-chipselects = <1>;
> +               cs-gpios = <&gpio0 ASPEED_GPIO(X, 0) GPIO_ACTIVE_LOW>;
> +
> +               tpmdev at 0 {

tpm at 0

> +                       compatible = "tcg,tpm_tis-spi";
> +                       spi-max-frequency = <33000000>;
> +                       reg = <0>;
> +               };
> +       };
>  };
>
>  &uart1 {
> --
> 2.25.1
>
>